rt2x00: fix some typos and punctuation in comments

fix some typos and punctuation in comments

Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@holoscopio.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

diff --git a/drivers/net/wireless/rt2x00/rt61pci.c b/drivers/net/wireless/rt2x00/rt61pci.c
index ea8a86f..6e46135 100644 (file)
--- a/drivers/net/wireless/rt2x00/rt61pci.c
+++ b/drivers/net/wireless/rt2x00/rt61pci.c
@@ -51,7 +51,7 @@ MODULE_PARM_DESC(nohwcrypt, "Disable hardware encryption.");
  * These indirect registers work with busy bits,
  * and we will try maximal REGISTER_BUSY_COUNT times to access
  * the register while taking a REGISTER_BUSY_DELAY us delay
- * between each attampt. When the busy bit is still set at that time,
+ * between each attempt. When the busy bit is still set at that time,
  * the access attempt is considered to have failed,
  * and we will print an error.
  */
@@ -386,7 +386,7 @@ static int rt61pci_config_shared_key(struct rt2x00_dev *rt2x00dev,
                 * The driver does not support the IV/EIV generation
                 * in hardware. However it doesn't support the IV/EIV
                 * inside the ieee80211 frame either, but requires it
-                * to be provided seperately for the descriptor.
+                * to be provided separately for the descriptor.
                 * rt2x00lib will cut the IV/EIV data out of all frames
                 * given to us by mac80211, but we must tell mac80211
                 * to generate the IV/EIV data.
@@ -397,7 +397,7 @@ static int rt61pci_config_shared_key(struct rt2x00_dev *rt2x00dev,
        /*
         * SEC_CSR0 contains only single-bit fields to indicate
         * a particular key is valid. Because using the FIELD32()
-        * defines directly will cause a lot of overhead we use
+        * defines directly will cause a lot of overhead, we use
         * a calculation to determine the correct bit directly.
         */
        mask = 1 << key->hw_key_idx;
@@ -425,11 +425,11 @@ static int rt61pci_config_pairwise_key(struct rt2x00_dev *rt2x00dev,
                /*
                 * rt2x00lib can't determine the correct free
                 * key_idx for pairwise keys. We have 2 registers
-                * with key valid bits. The goal is simple, read
-                * the first register, if that is full move to
+                * with key valid bits. The goal is simple: read
+                * the first register. If that is full, move to
                 * the next register.
-                * When both registers are full, we drop the key,
-                * otherwise we use the first invalid entry.
+                * When both registers are full, we drop the key.
+                * Otherwise, we use the first invalid entry.
                 */
                rt2x00pci_register_read(rt2x00dev, SEC_CSR2, &reg);
                if (reg && reg == ~0) {
@@ -464,8 +464,8 @@ static int rt61pci_config_pairwise_key(struct rt2x00_dev *rt2x00dev,
                                              &addr_entry, sizeof(addr_entry));
 
                /*
-                * Enable pairwise lookup table for given BSS idx,
-                * without this received frames will not be decrypted
+                * Enable pairwise lookup table for given BSS idx.
+                * Without this, received frames will not be decrypted
                 * by the hardware.
                 */
                rt2x00pci_register_read(rt2x00dev, SEC_CSR4, &reg);
@@ -487,7 +487,7 @@ static int rt61pci_config_pairwise_key(struct rt2x00_dev *rt2x00dev,
        /*
         * SEC_CSR2 and SEC_CSR3 contain only single-bit fields to indicate
         * a particular key is valid. Because using the FIELD32()
-        * defines directly will cause a lot of overhead we use
+        * defines directly will cause a lot of overhead, we use
         * a calculation to determine the correct bit directly.
         */
        if (key->hw_key_idx < 32) {
@@ -556,7 +556,7 @@ static void rt61pci_config_intf(struct rt2x00_dev *rt2x00dev,
        if (flags & CONFIG_UPDATE_TYPE) {
                /*
                 * Clear current synchronisation setup.
-                * For the Beacon base registers we only need to clear
+                * For the Beacon base registers, we only need to clear
                 * the first byte since that byte contains the VALID and OWNER
                 * bits which (when set to 0) will invalidate the entire beacon.
                 */
@@ -1168,8 +1168,8 @@ static int rt61pci_check_firmware(struct rt2x00_dev *rt2x00dev,
                return FW_BAD_LENGTH;
 
        /*
-        * The last 2 bytes in the firmware array are the crc checksum itself,
-        * this means that we should never pass those 2 bytes to the crc
+        * The last 2 bytes in the firmware array are the crc checksum itself.
+        * This means that we should never pass those 2 bytes to the crc
         * algorithm.
         */
        fw_crc = (data[len - 2] << 8 | data[len - 1]);
@@ -1986,7 +1986,7 @@ static void rt61pci_fill_rxdone(struct queue_entry *entry,
 
                /*
                 * Hardware has stripped IV/EIV data from 802.11 frame during
-                * decryption. It has provided the data seperately but rt2x00lib
+                * decryption. It has provided the data separately but rt2x00lib
                 * should decide if it should be reinserted.
                 */
                rxdesc->flags |= RX_FLAG_IV_STRIPPED;
@@ -2042,7 +2042,7 @@ static void rt61pci_txdone(struct rt2x00_dev *rt2x00dev)
         * During each loop we will compare the freshly read
         * STA_CSR4 register value with the value read from
         * the previous loop. If the 2 values are equal then
-        * we should stop processing because the chance it
+        * we should stop processing because the chance is
         * quite big that the device has been unplugged and
         * we risk going into an endless loop.
         */
@@ -2330,7 +2330,7 @@ static int rt61pci_init_eeprom(struct rt2x00_dev *rt2x00dev)
                __set_bit(CONFIG_FRAME_TYPE, &rt2x00dev->flags);
 
        /*
-        * Detect if this device has an hardware controlled radio.
+        * Detect if this device has a hardware controlled radio.
         */
        if (rt2x00_get_field16(eeprom, EEPROM_ANTENNA_HARDWARE_RADIO))
                __set_bit(CONFIG_SUPPORT_HW_BUTTON, &rt2x00dev->flags);
@@ -2355,7 +2355,7 @@ static int rt61pci_init_eeprom(struct rt2x00_dev *rt2x00dev)
                __set_bit(CONFIG_EXTERNAL_LNA_BG, &rt2x00dev->flags);
 
        /*
-        * When working with a RF2529 chip without double antenna
+        * When working with a RF2529 chip without double antenna,
         * the antenna settings should be gathered from the NIC
         * eeprom word.
         */
@@ -2668,7 +2668,7 @@ static int rt61pci_conf_tx(struct ieee80211_hw *hw, u16 queue_idx,
 
        /*
         * We only need to perform additional register initialization
-        * for WMM queues/
+        * for WMM queues.
         */
        if (queue_idx >= 4)
                return 0;