/* include all Core registers and bit definitions */
#include "defBF527.h"
-/* include core specific register pointer definitions */
-#include <asm/cdef_LPBlackfin.h>
-
-/* SYSTEM & MMR ADDRESS DEFINITIONS FOR ADSP-BF527 */
-
-/* include cdefBF52x_base.h for the set of #defines that are common to all ADSP-BF52x processors */
-#include "cdefBF52x_base.h"
-
-/* The following are the #defines needed by ADSP-BF527 that are not in the common header */
+/* BF527 is BF525 + EMAC */
+#include "cdefBF525.h"
/* 10/100 Ethernet Controller (0xFFC03000 - 0xFFC031FF) */
#define bfin_read_EMAC_TXC_ABORT() bfin_read32(EMAC_TXC_ABORT)
#define bfin_write_EMAC_TXC_ABORT(val) bfin_write32(EMAC_TXC_ABORT, val)
-/* USB Control Registers */
-
-#define bfin_read_USB_FADDR() bfin_read16(USB_FADDR)
-#define bfin_write_USB_FADDR(val) bfin_write16(USB_FADDR, val)
-#define bfin_read_USB_POWER() bfin_read16(USB_POWER)
-#define bfin_write_USB_POWER(val) bfin_write16(USB_POWER, val)
-#define bfin_read_USB_INTRTX() bfin_read16(USB_INTRTX)
-#define bfin_write_USB_INTRTX(val) bfin_write16(USB_INTRTX, val)
-#define bfin_read_USB_INTRRX() bfin_read16(USB_INTRRX)
-#define bfin_write_USB_INTRRX(val) bfin_write16(USB_INTRRX, val)
-#define bfin_read_USB_INTRTXE() bfin_read16(USB_INTRTXE)
-#define bfin_write_USB_INTRTXE(val) bfin_write16(USB_INTRTXE, val)
-#define bfin_read_USB_INTRRXE() bfin_read16(USB_INTRRXE)
-#define bfin_write_USB_INTRRXE(val) bfin_write16(USB_INTRRXE, val)
-#define bfin_read_USB_INTRUSB() bfin_read16(USB_INTRUSB)
-#define bfin_write_USB_INTRUSB(val) bfin_write16(USB_INTRUSB, val)
-#define bfin_read_USB_INTRUSBE() bfin_read16(USB_INTRUSBE)
-#define bfin_write_USB_INTRUSBE(val) bfin_write16(USB_INTRUSBE, val)
-#define bfin_read_USB_FRAME() bfin_read16(USB_FRAME)
-#define bfin_write_USB_FRAME(val) bfin_write16(USB_FRAME, val)
-#define bfin_read_USB_INDEX() bfin_read16(USB_INDEX)
-#define bfin_write_USB_INDEX(val) bfin_write16(USB_INDEX, val)
-#define bfin_read_USB_TESTMODE() bfin_read16(USB_TESTMODE)
-#define bfin_write_USB_TESTMODE(val) bfin_write16(USB_TESTMODE, val)
-#define bfin_read_USB_GLOBINTR() bfin_read16(USB_GLOBINTR)
-#define bfin_write_USB_GLOBINTR(val) bfin_write16(USB_GLOBINTR, val)
-#define bfin_read_USB_GLOBAL_CTL() bfin_read16(USB_GLOBAL_CTL)
-#define bfin_write_USB_GLOBAL_CTL(val) bfin_write16(USB_GLOBAL_CTL, val)
-
-/* USB Packet Control Registers */
-
-#define bfin_read_USB_TX_MAX_PACKET() bfin_read16(USB_TX_MAX_PACKET)
-#define bfin_write_USB_TX_MAX_PACKET(val) bfin_write16(USB_TX_MAX_PACKET, val)
-#define bfin_read_USB_CSR0() bfin_read16(USB_CSR0)
-#define bfin_write_USB_CSR0(val) bfin_write16(USB_CSR0, val)
-#define bfin_read_USB_TXCSR() bfin_read16(USB_TXCSR)
-#define bfin_write_USB_TXCSR(val) bfin_write16(USB_TXCSR, val)
-#define bfin_read_USB_RX_MAX_PACKET() bfin_read16(USB_RX_MAX_PACKET)
-#define bfin_write_USB_RX_MAX_PACKET(val) bfin_write16(USB_RX_MAX_PACKET, val)
-#define bfin_read_USB_RXCSR() bfin_read16(USB_RXCSR)
-#define bfin_write_USB_RXCSR(val) bfin_write16(USB_RXCSR, val)
-#define bfin_read_USB_COUNT0() bfin_read16(USB_COUNT0)
-#define bfin_write_USB_COUNT0(val) bfin_write16(USB_COUNT0, val)
-#define bfin_read_USB_RXCOUNT() bfin_read16(USB_RXCOUNT)
-#define bfin_write_USB_RXCOUNT(val) bfin_write16(USB_RXCOUNT, val)
-#define bfin_read_USB_TXTYPE() bfin_read16(USB_TXTYPE)
-#define bfin_write_USB_TXTYPE(val) bfin_write16(USB_TXTYPE, val)
-#define bfin_read_USB_NAKLIMIT0() bfin_read16(USB_NAKLIMIT0)
-#define bfin_write_USB_NAKLIMIT0(val) bfin_write16(USB_NAKLIMIT0, val)
-#define bfin_read_USB_TXINTERVAL() bfin_read16(USB_TXINTERVAL)
-#define bfin_write_USB_TXINTERVAL(val) bfin_write16(USB_TXINTERVAL, val)
-#define bfin_read_USB_RXTYPE() bfin_read16(USB_RXTYPE)
-#define bfin_write_USB_RXTYPE(val) bfin_write16(USB_RXTYPE, val)
-#define bfin_read_USB_RXINTERVAL() bfin_read16(USB_RXINTERVAL)
-#define bfin_write_USB_RXINTERVAL(val) bfin_write16(USB_RXINTERVAL, val)
-#define bfin_read_USB_TXCOUNT() bfin_read16(USB_TXCOUNT)
-#define bfin_write_USB_TXCOUNT(val) bfin_write16(USB_TXCOUNT, val)
-
-/* USB Endpoint FIFO Registers */
-
-#define bfin_read_USB_EP0_FIFO() bfin_read16(USB_EP0_FIFO)
-#define bfin_write_USB_EP0_FIFO(val) bfin_write16(USB_EP0_FIFO, val)
-#define bfin_read_USB_EP1_FIFO() bfin_read16(USB_EP1_FIFO)
-#define bfin_write_USB_EP1_FIFO(val) bfin_write16(USB_EP1_FIFO, val)
-#define bfin_read_USB_EP2_FIFO() bfin_read16(USB_EP2_FIFO)
-#define bfin_write_USB_EP2_FIFO(val) bfin_write16(USB_EP2_FIFO, val)
-#define bfin_read_USB_EP3_FIFO() bfin_read16(USB_EP3_FIFO)
-#define bfin_write_USB_EP3_FIFO(val) bfin_write16(USB_EP3_FIFO, val)
-#define bfin_read_USB_EP4_FIFO() bfin_read16(USB_EP4_FIFO)
-#define bfin_write_USB_EP4_FIFO(val) bfin_write16(USB_EP4_FIFO, val)
-#define bfin_read_USB_EP5_FIFO() bfin_read16(USB_EP5_FIFO)
-#define bfin_write_USB_EP5_FIFO(val) bfin_write16(USB_EP5_FIFO, val)
-#define bfin_read_USB_EP6_FIFO() bfin_read16(USB_EP6_FIFO)
-#define bfin_write_USB_EP6_FIFO(val) bfin_write16(USB_EP6_FIFO, val)
-#define bfin_read_USB_EP7_FIFO() bfin_read16(USB_EP7_FIFO)
-#define bfin_write_USB_EP7_FIFO(val) bfin_write16(USB_EP7_FIFO, val)
-
-/* USB OTG Control Registers */
-
-#define bfin_read_USB_OTG_DEV_CTL() bfin_read16(USB_OTG_DEV_CTL)
-#define bfin_write_USB_OTG_DEV_CTL(val) bfin_write16(USB_OTG_DEV_CTL, val)
-#define bfin_read_USB_OTG_VBUS_IRQ() bfin_read16(USB_OTG_VBUS_IRQ)
-#define bfin_write_USB_OTG_VBUS_IRQ(val) bfin_write16(USB_OTG_VBUS_IRQ, val)
-#define bfin_read_USB_OTG_VBUS_MASK() bfin_read16(USB_OTG_VBUS_MASK)
-#define bfin_write_USB_OTG_VBUS_MASK(val) bfin_write16(USB_OTG_VBUS_MASK, val)
-
-/* USB Phy Control Registers */
-
-#define bfin_read_USB_LINKINFO() bfin_read16(USB_LINKINFO)
-#define bfin_write_USB_LINKINFO(val) bfin_write16(USB_LINKINFO, val)
-#define bfin_read_USB_VPLEN() bfin_read16(USB_VPLEN)
-#define bfin_write_USB_VPLEN(val) bfin_write16(USB_VPLEN, val)
-#define bfin_read_USB_HS_EOF1() bfin_read16(USB_HS_EOF1)
-#define bfin_write_USB_HS_EOF1(val) bfin_write16(USB_HS_EOF1, val)
-#define bfin_read_USB_FS_EOF1() bfin_read16(USB_FS_EOF1)
-#define bfin_write_USB_FS_EOF1(val) bfin_write16(USB_FS_EOF1, val)
-#define bfin_read_USB_LS_EOF1() bfin_read16(USB_LS_EOF1)
-#define bfin_write_USB_LS_EOF1(val) bfin_write16(USB_LS_EOF1, val)
-
-/* (APHY_CNTRL is for ADI usage only) */
-
-#define bfin_read_USB_APHY_CNTRL() bfin_read16(USB_APHY_CNTRL)
-#define bfin_write_USB_APHY_CNTRL(val) bfin_write16(USB_APHY_CNTRL, val)
-
-/* (APHY_CALIB is for ADI usage only) */
-
-#define bfin_read_USB_APHY_CALIB() bfin_read16(USB_APHY_CALIB)
-#define bfin_write_USB_APHY_CALIB(val) bfin_write16(USB_APHY_CALIB, val)
-
-#define bfin_read_USB_APHY_CNTRL2() bfin_read16(USB_APHY_CNTRL2)
-#define bfin_write_USB_APHY_CNTRL2(val) bfin_write16(USB_APHY_CNTRL2, val)
-
-/* (PHY_TEST is for ADI usage only) */
-
-#define bfin_read_USB_PHY_TEST() bfin_read16(USB_PHY_TEST)
-#define bfin_write_USB_PHY_TEST(val) bfin_write16(USB_PHY_TEST, val)
-
-#define bfin_read_USB_PLLOSC_CTRL() bfin_read16(USB_PLLOSC_CTRL)
-#define bfin_write_USB_PLLOSC_CTRL(val) bfin_write16(USB_PLLOSC_CTRL, val)
-#define bfin_read_USB_SRP_CLKDIV() bfin_read16(USB_SRP_CLKDIV)
-#define bfin_write_USB_SRP_CLKDIV(val) bfin_write16(USB_SRP_CLKDIV, val)
-
-/* USB Endpoint 0 Control Registers */
-
-#define bfin_read_USB_EP_NI0_TXMAXP() bfin_read16(USB_EP_NI0_TXMAXP)
-#define bfin_write_USB_EP_NI0_TXMAXP(val) bfin_write16(USB_EP_NI0_TXMAXP, val)
-#define bfin_read_USB_EP_NI0_TXCSR() bfin_read16(USB_EP_NI0_TXCSR)
-#define bfin_write_USB_EP_NI0_TXCSR(val) bfin_write16(USB_EP_NI0_TXCSR, val)
-#define bfin_read_USB_EP_NI0_RXMAXP() bfin_read16(USB_EP_NI0_RXMAXP)
-#define bfin_write_USB_EP_NI0_RXMAXP(val) bfin_write16(USB_EP_NI0_RXMAXP, val)
-#define bfin_read_USB_EP_NI0_RXCSR() bfin_read16(USB_EP_NI0_RXCSR)
-#define bfin_write_USB_EP_NI0_RXCSR(val) bfin_write16(USB_EP_NI0_RXCSR, val)
-#define bfin_read_USB_EP_NI0_RXCOUNT() bfin_read16(USB_EP_NI0_RXCOUNT)
-#define bfin_write_USB_EP_NI0_RXCOUNT(val) bfin_write16(USB_EP_NI0_RXCOUNT, val)
-#define bfin_read_USB_EP_NI0_TXTYPE() bfin_read16(USB_EP_NI0_TXTYPE)
-#define bfin_write_USB_EP_NI0_TXTYPE(val) bfin_write16(USB_EP_NI0_TXTYPE, val)
-#define bfin_read_USB_EP_NI0_TXINTERVAL() bfin_read16(USB_EP_NI0_TXINTERVAL)
-#define bfin_write_USB_EP_NI0_TXINTERVAL(val) bfin_write16(USB_EP_NI0_TXINTERVAL, val)
-#define bfin_read_USB_EP_NI0_RXTYPE() bfin_read16(USB_EP_NI0_RXTYPE)
-#define bfin_write_USB_EP_NI0_RXTYPE(val) bfin_write16(USB_EP_NI0_RXTYPE, val)
-#define bfin_read_USB_EP_NI0_RXINTERVAL() bfin_read16(USB_EP_NI0_RXINTERVAL)
-#define bfin_write_USB_EP_NI0_RXINTERVAL(val) bfin_write16(USB_EP_NI0_RXINTERVAL, val)
-#define bfin_read_USB_EP_NI0_TXCOUNT() bfin_read16(USB_EP_NI0_TXCOUNT)
-#define bfin_write_USB_EP_NI0_TXCOUNT(val) bfin_write16(USB_EP_NI0_TXCOUNT, val)
-
-/* USB Endpoint 1 Control Registers */
-
-#define bfin_read_USB_EP_NI1_TXMAXP() bfin_read16(USB_EP_NI1_TXMAXP)
-#define bfin_write_USB_EP_NI1_TXMAXP(val) bfin_write16(USB_EP_NI1_TXMAXP, val)
-#define bfin_read_USB_EP_NI1_TXCSR() bfin_read16(USB_EP_NI1_TXCSR)
-#define bfin_write_USB_EP_NI1_TXCSR(val) bfin_write16(USB_EP_NI1_TXCSR, val)
-#define bfin_read_USB_EP_NI1_RXMAXP() bfin_read16(USB_EP_NI1_RXMAXP)
-#define bfin_write_USB_EP_NI1_RXMAXP(val) bfin_write16(USB_EP_NI1_RXMAXP, val)
-#define bfin_read_USB_EP_NI1_RXCSR() bfin_read16(USB_EP_NI1_RXCSR)
-#define bfin_write_USB_EP_NI1_RXCSR(val) bfin_write16(USB_EP_NI1_RXCSR, val)
-#define bfin_read_USB_EP_NI1_RXCOUNT() bfin_read16(USB_EP_NI1_RXCOUNT)
-#define bfin_write_USB_EP_NI1_RXCOUNT(val) bfin_write16(USB_EP_NI1_RXCOUNT, val)
-#define bfin_read_USB_EP_NI1_TXTYPE() bfin_read16(USB_EP_NI1_TXTYPE)
-#define bfin_write_USB_EP_NI1_TXTYPE(val) bfin_write16(USB_EP_NI1_TXTYPE, val)
-#define bfin_read_USB_EP_NI1_TXINTERVAL() bfin_read16(USB_EP_NI1_TXINTERVAL)
-#define bfin_write_USB_EP_NI1_TXINTERVAL(val) bfin_write16(USB_EP_NI1_TXINTERVAL, val)
-#define bfin_read_USB_EP_NI1_RXTYPE() bfin_read16(USB_EP_NI1_RXTYPE)
-#define bfin_write_USB_EP_NI1_RXTYPE(val) bfin_write16(USB_EP_NI1_RXTYPE, val)
-#define bfin_read_USB_EP_NI1_RXINTERVAL() bfin_read16(USB_EP_NI1_RXINTERVAL)
-#define bfin_write_USB_EP_NI1_RXINTERVAL(val) bfin_write16(USB_EP_NI1_RXINTERVAL, val)
-#define bfin_read_USB_EP_NI1_TXCOUNT() bfin_read16(USB_EP_NI1_TXCOUNT)
-#define bfin_write_USB_EP_NI1_TXCOUNT(val) bfin_write16(USB_EP_NI1_TXCOUNT, val)
-
-/* USB Endpoint 2 Control Registers */
-
-#define bfin_read_USB_EP_NI2_TXMAXP() bfin_read16(USB_EP_NI2_TXMAXP)
-#define bfin_write_USB_EP_NI2_TXMAXP(val) bfin_write16(USB_EP_NI2_TXMAXP, val)
-#define bfin_read_USB_EP_NI2_TXCSR() bfin_read16(USB_EP_NI2_TXCSR)
-#define bfin_write_USB_EP_NI2_TXCSR(val) bfin_write16(USB_EP_NI2_TXCSR, val)
-#define bfin_read_USB_EP_NI2_RXMAXP() bfin_read16(USB_EP_NI2_RXMAXP)
-#define bfin_write_USB_EP_NI2_RXMAXP(val) bfin_write16(USB_EP_NI2_RXMAXP, val)
-#define bfin_read_USB_EP_NI2_RXCSR() bfin_read16(USB_EP_NI2_RXCSR)
-#define bfin_write_USB_EP_NI2_RXCSR(val) bfin_write16(USB_EP_NI2_RXCSR, val)
-#define bfin_read_USB_EP_NI2_RXCOUNT() bfin_read16(USB_EP_NI2_RXCOUNT)
-#define bfin_write_USB_EP_NI2_RXCOUNT(val) bfin_write16(USB_EP_NI2_RXCOUNT, val)
-#define bfin_read_USB_EP_NI2_TXTYPE() bfin_read16(USB_EP_NI2_TXTYPE)
-#define bfin_write_USB_EP_NI2_TXTYPE(val) bfin_write16(USB_EP_NI2_TXTYPE, val)
-#define bfin_read_USB_EP_NI2_TXINTERVAL() bfin_read16(USB_EP_NI2_TXINTERVAL)
-#define bfin_write_USB_EP_NI2_TXINTERVAL(val) bfin_write16(USB_EP_NI2_TXINTERVAL, val)
-#define bfin_read_USB_EP_NI2_RXTYPE() bfin_read16(USB_EP_NI2_RXTYPE)
-#define bfin_write_USB_EP_NI2_RXTYPE(val) bfin_write16(USB_EP_NI2_RXTYPE, val)
-#define bfin_read_USB_EP_NI2_RXINTERVAL() bfin_read16(USB_EP_NI2_RXINTERVAL)
-#define bfin_write_USB_EP_NI2_RXINTERVAL(val) bfin_write16(USB_EP_NI2_RXINTERVAL, val)
-#define bfin_read_USB_EP_NI2_TXCOUNT() bfin_read16(USB_EP_NI2_TXCOUNT)
-#define bfin_write_USB_EP_NI2_TXCOUNT(val) bfin_write16(USB_EP_NI2_TXCOUNT, val)
-
-/* USB Endpoint 3 Control Registers */
-
-#define bfin_read_USB_EP_NI3_TXMAXP() bfin_read16(USB_EP_NI3_TXMAXP)
-#define bfin_write_USB_EP_NI3_TXMAXP(val) bfin_write16(USB_EP_NI3_TXMAXP, val)
-#define bfin_read_USB_EP_NI3_TXCSR() bfin_read16(USB_EP_NI3_TXCSR)
-#define bfin_write_USB_EP_NI3_TXCSR(val) bfin_write16(USB_EP_NI3_TXCSR, val)
-#define bfin_read_USB_EP_NI3_RXMAXP() bfin_read16(USB_EP_NI3_RXMAXP)
-#define bfin_write_USB_EP_NI3_RXMAXP(val) bfin_write16(USB_EP_NI3_RXMAXP, val)
-#define bfin_read_USB_EP_NI3_RXCSR() bfin_read16(USB_EP_NI3_RXCSR)
-#define bfin_write_USB_EP_NI3_RXCSR(val) bfin_write16(USB_EP_NI3_RXCSR, val)
-#define bfin_read_USB_EP_NI3_RXCOUNT() bfin_read16(USB_EP_NI3_RXCOUNT)
-#define bfin_write_USB_EP_NI3_RXCOUNT(val) bfin_write16(USB_EP_NI3_RXCOUNT, val)
-#define bfin_read_USB_EP_NI3_TXTYPE() bfin_read16(USB_EP_NI3_TXTYPE)
-#define bfin_write_USB_EP_NI3_TXTYPE(val) bfin_write16(USB_EP_NI3_TXTYPE, val)
-#define bfin_read_USB_EP_NI3_TXINTERVAL() bfin_read16(USB_EP_NI3_TXINTERVAL)
-#define bfin_write_USB_EP_NI3_TXINTERVAL(val) bfin_write16(USB_EP_NI3_TXINTERVAL, val)
-#define bfin_read_USB_EP_NI3_RXTYPE() bfin_read16(USB_EP_NI3_RXTYPE)
-#define bfin_write_USB_EP_NI3_RXTYPE(val) bfin_write16(USB_EP_NI3_RXTYPE, val)
-#define bfin_read_USB_EP_NI3_RXINTERVAL() bfin_read16(USB_EP_NI3_RXINTERVAL)
-#define bfin_write_USB_EP_NI3_RXINTERVAL(val) bfin_write16(USB_EP_NI3_RXINTERVAL, val)
-#define bfin_read_USB_EP_NI3_TXCOUNT() bfin_read16(USB_EP_NI3_TXCOUNT)
-#define bfin_write_USB_EP_NI3_TXCOUNT(val) bfin_write16(USB_EP_NI3_TXCOUNT, val)
-
-/* USB Endpoint 4 Control Registers */
-
-#define bfin_read_USB_EP_NI4_TXMAXP() bfin_read16(USB_EP_NI4_TXMAXP)
-#define bfin_write_USB_EP_NI4_TXMAXP(val) bfin_write16(USB_EP_NI4_TXMAXP, val)
-#define bfin_read_USB_EP_NI4_TXCSR() bfin_read16(USB_EP_NI4_TXCSR)
-#define bfin_write_USB_EP_NI4_TXCSR(val) bfin_write16(USB_EP_NI4_TXCSR, val)
-#define bfin_read_USB_EP_NI4_RXMAXP() bfin_read16(USB_EP_NI4_RXMAXP)
-#define bfin_write_USB_EP_NI4_RXMAXP(val) bfin_write16(USB_EP_NI4_RXMAXP, val)
-#define bfin_read_USB_EP_NI4_RXCSR() bfin_read16(USB_EP_NI4_RXCSR)
-#define bfin_write_USB_EP_NI4_RXCSR(val) bfin_write16(USB_EP_NI4_RXCSR, val)
-#define bfin_read_USB_EP_NI4_RXCOUNT() bfin_read16(USB_EP_NI4_RXCOUNT)
-#define bfin_write_USB_EP_NI4_RXCOUNT(val) bfin_write16(USB_EP_NI4_RXCOUNT, val)
-#define bfin_read_USB_EP_NI4_TXTYPE() bfin_read16(USB_EP_NI4_TXTYPE)
-#define bfin_write_USB_EP_NI4_TXTYPE(val) bfin_write16(USB_EP_NI4_TXTYPE, val)
-#define bfin_read_USB_EP_NI4_TXINTERVAL() bfin_read16(USB_EP_NI4_TXINTERVAL)
-#define bfin_write_USB_EP_NI4_TXINTERVAL(val) bfin_write16(USB_EP_NI4_TXINTERVAL, val)
-#define bfin_read_USB_EP_NI4_RXTYPE() bfin_read16(USB_EP_NI4_RXTYPE)
-#define bfin_write_USB_EP_NI4_RXTYPE(val) bfin_write16(USB_EP_NI4_RXTYPE, val)
-#define bfin_read_USB_EP_NI4_RXINTERVAL() bfin_read16(USB_EP_NI4_RXINTERVAL)
-#define bfin_write_USB_EP_NI4_RXINTERVAL(val) bfin_write16(USB_EP_NI4_RXINTERVAL, val)
-#define bfin_read_USB_EP_NI4_TXCOUNT() bfin_read16(USB_EP_NI4_TXCOUNT)
-#define bfin_write_USB_EP_NI4_TXCOUNT(val) bfin_write16(USB_EP_NI4_TXCOUNT, val)
-
-/* USB Endpoint 5 Control Registers */
-
-#define bfin_read_USB_EP_NI5_TXMAXP() bfin_read16(USB_EP_NI5_TXMAXP)
-#define bfin_write_USB_EP_NI5_TXMAXP(val) bfin_write16(USB_EP_NI5_TXMAXP, val)
-#define bfin_read_USB_EP_NI5_TXCSR() bfin_read16(USB_EP_NI5_TXCSR)
-#define bfin_write_USB_EP_NI5_TXCSR(val) bfin_write16(USB_EP_NI5_TXCSR, val)
-#define bfin_read_USB_EP_NI5_RXMAXP() bfin_read16(USB_EP_NI5_RXMAXP)
-#define bfin_write_USB_EP_NI5_RXMAXP(val) bfin_write16(USB_EP_NI5_RXMAXP, val)
-#define bfin_read_USB_EP_NI5_RXCSR() bfin_read16(USB_EP_NI5_RXCSR)
-#define bfin_write_USB_EP_NI5_RXCSR(val) bfin_write16(USB_EP_NI5_RXCSR, val)
-#define bfin_read_USB_EP_NI5_RXCOUNT() bfin_read16(USB_EP_NI5_RXCOUNT)
-#define bfin_write_USB_EP_NI5_RXCOUNT(val) bfin_write16(USB_EP_NI5_RXCOUNT, val)
-#define bfin_read_USB_EP_NI5_TXTYPE() bfin_read16(USB_EP_NI5_TXTYPE)
-#define bfin_write_USB_EP_NI5_TXTYPE(val) bfin_write16(USB_EP_NI5_TXTYPE, val)
-#define bfin_read_USB_EP_NI5_TXINTERVAL() bfin_read16(USB_EP_NI5_TXINTERVAL)
-#define bfin_write_USB_EP_NI5_TXINTERVAL(val) bfin_write16(USB_EP_NI5_TXINTERVAL, val)
-#define bfin_read_USB_EP_NI5_RXTYPE() bfin_read16(USB_EP_NI5_RXTYPE)
-#define bfin_write_USB_EP_NI5_RXTYPE(val) bfin_write16(USB_EP_NI5_RXTYPE, val)
-#define bfin_read_USB_EP_NI5_RXINTERVAL() bfin_read16(USB_EP_NI5_RXINTERVAL)
-#define bfin_write_USB_EP_NI5_RXINTERVAL(val) bfin_write16(USB_EP_NI5_RXINTERVAL, val)
-#define bfin_read_USB_EP_NI5_TXCOUNT() bfin_read16(USB_EP_NI5_TXCOUNT)
-#define bfin_write_USB_EP_NI5_TXCOUNT(val) bfin_write16(USB_EP_NI5_TXCOUNT, val)
-
-/* USB Endpoint 6 Control Registers */
-
-#define bfin_read_USB_EP_NI6_TXMAXP() bfin_read16(USB_EP_NI6_TXMAXP)
-#define bfin_write_USB_EP_NI6_TXMAXP(val) bfin_write16(USB_EP_NI6_TXMAXP, val)
-#define bfin_read_USB_EP_NI6_TXCSR() bfin_read16(USB_EP_NI6_TXCSR)
-#define bfin_write_USB_EP_NI6_TXCSR(val) bfin_write16(USB_EP_NI6_TXCSR, val)
-#define bfin_read_USB_EP_NI6_RXMAXP() bfin_read16(USB_EP_NI6_RXMAXP)
-#define bfin_write_USB_EP_NI6_RXMAXP(val) bfin_write16(USB_EP_NI6_RXMAXP, val)
-#define bfin_read_USB_EP_NI6_RXCSR() bfin_read16(USB_EP_NI6_RXCSR)
-#define bfin_write_USB_EP_NI6_RXCSR(val) bfin_write16(USB_EP_NI6_RXCSR, val)
-#define bfin_read_USB_EP_NI6_RXCOUNT() bfin_read16(USB_EP_NI6_RXCOUNT)
-#define bfin_write_USB_EP_NI6_RXCOUNT(val) bfin_write16(USB_EP_NI6_RXCOUNT, val)
-#define bfin_read_USB_EP_NI6_TXTYPE() bfin_read16(USB_EP_NI6_TXTYPE)
-#define bfin_write_USB_EP_NI6_TXTYPE(val) bfin_write16(USB_EP_NI6_TXTYPE, val)
-#define bfin_read_USB_EP_NI6_TXINTERVAL() bfin_read16(USB_EP_NI6_TXINTERVAL)
-#define bfin_write_USB_EP_NI6_TXINTERVAL(val) bfin_write16(USB_EP_NI6_TXINTERVAL, val)
-#define bfin_read_USB_EP_NI6_RXTYPE() bfin_read16(USB_EP_NI6_RXTYPE)
-#define bfin_write_USB_EP_NI6_RXTYPE(val) bfin_write16(USB_EP_NI6_RXTYPE, val)
-#define bfin_read_USB_EP_NI6_RXINTERVAL() bfin_read16(USB_EP_NI6_RXINTERVAL)
-#define bfin_write_USB_EP_NI6_RXINTERVAL(val) bfin_write16(USB_EP_NI6_RXINTERVAL, val)
-#define bfin_read_USB_EP_NI6_TXCOUNT() bfin_read16(USB_EP_NI6_TXCOUNT)
-#define bfin_write_USB_EP_NI6_TXCOUNT(val) bfin_write16(USB_EP_NI6_TXCOUNT, val)
-
-/* USB Endpoint 7 Control Registers */
-
-#define bfin_read_USB_EP_NI7_TXMAXP() bfin_read16(USB_EP_NI7_TXMAXP)
-#define bfin_write_USB_EP_NI7_TXMAXP(val) bfin_write16(USB_EP_NI7_TXMAXP, val)
-#define bfin_read_USB_EP_NI7_TXCSR() bfin_read16(USB_EP_NI7_TXCSR)
-#define bfin_write_USB_EP_NI7_TXCSR(val) bfin_write16(USB_EP_NI7_TXCSR, val)
-#define bfin_read_USB_EP_NI7_RXMAXP() bfin_read16(USB_EP_NI7_RXMAXP)
-#define bfin_write_USB_EP_NI7_RXMAXP(val) bfin_write16(USB_EP_NI7_RXMAXP, val)
-#define bfin_read_USB_EP_NI7_RXCSR() bfin_read16(USB_EP_NI7_RXCSR)
-#define bfin_write_USB_EP_NI7_RXCSR(val) bfin_write16(USB_EP_NI7_RXCSR, val)
-#define bfin_read_USB_EP_NI7_RXCOUNT() bfin_read16(USB_EP_NI7_RXCOUNT)
-#define bfin_write_USB_EP_NI7_RXCOUNT(val) bfin_write16(USB_EP_NI7_RXCOUNT, val)
-#define bfin_read_USB_EP_NI7_TXTYPE() bfin_read16(USB_EP_NI7_TXTYPE)
-#define bfin_write_USB_EP_NI7_TXTYPE(val) bfin_write16(USB_EP_NI7_TXTYPE, val)
-#define bfin_read_USB_EP_NI7_TXINTERVAL() bfin_read16(USB_EP_NI7_TXINTERVAL)
-#define bfin_write_USB_EP_NI7_TXINTERVAL(val) bfin_write16(USB_EP_NI7_TXINTERVAL, val)
-#define bfin_read_USB_EP_NI7_RXTYPE() bfin_read16(USB_EP_NI7_RXTYPE)
-#define bfin_write_USB_EP_NI7_RXTYPE(val) bfin_write16(USB_EP_NI7_RXTYPE, val)
-#define bfin_read_USB_EP_NI7_RXINTERVAL() bfin_read16(USB_EP_NI7_RXINTERVAL)
-#define bfin_write_USB_EP_NI7_RXINTERVAL(val) bfin_write16(USB_EP_NI7_RXINTERVAL, val)
-#define bfin_read_USB_EP_NI7_TXCOUNT() bfin_read16(USB_EP_NI7_TXCOUNT)
-#define bfin_write_USB_EP_NI7_TXCOUNT(val) bfin_write16(USB_EP_NI7_TXCOUNT, val)
-
-#define bfin_read_USB_DMA_INTERRUPT() bfin_read16(USB_DMA_INTERRUPT)
-#define bfin_write_USB_DMA_INTERRUPT(val) bfin_write16(USB_DMA_INTERRUPT, val)
-
-/* USB Channel 0 Config Registers */
-
-#define bfin_read_USB_DMA0CONTROL() bfin_read16(USB_DMA0CONTROL)
-#define bfin_write_USB_DMA0CONTROL(val) bfin_write16(USB_DMA0CONTROL, val)
-#define bfin_read_USB_DMA0ADDRLOW() bfin_read16(USB_DMA0ADDRLOW)
-#define bfin_write_USB_DMA0ADDRLOW(val) bfin_write16(USB_DMA0ADDRLOW, val)
-#define bfin_read_USB_DMA0ADDRHIGH() bfin_read16(USB_DMA0ADDRHIGH)
-#define bfin_write_USB_DMA0ADDRHIGH(val) bfin_write16(USB_DMA0ADDRHIGH, val)
-#define bfin_read_USB_DMA0COUNTLOW() bfin_read16(USB_DMA0COUNTLOW)
-#define bfin_write_USB_DMA0COUNTLOW(val) bfin_write16(USB_DMA0COUNTLOW, val)
-#define bfin_read_USB_DMA0COUNTHIGH() bfin_read16(USB_DMA0COUNTHIGH)
-#define bfin_write_USB_DMA0COUNTHIGH(val) bfin_write16(USB_DMA0COUNTHIGH, val)
-
-/* USB Channel 1 Config Registers */
-
-#define bfin_read_USB_DMA1CONTROL() bfin_read16(USB_DMA1CONTROL)
-#define bfin_write_USB_DMA1CONTROL(val) bfin_write16(USB_DMA1CONTROL, val)
-#define bfin_read_USB_DMA1ADDRLOW() bfin_read16(USB_DMA1ADDRLOW)
-#define bfin_write_USB_DMA1ADDRLOW(val) bfin_write16(USB_DMA1ADDRLOW, val)
-#define bfin_read_USB_DMA1ADDRHIGH() bfin_read16(USB_DMA1ADDRHIGH)
-#define bfin_write_USB_DMA1ADDRHIGH(val) bfin_write16(USB_DMA1ADDRHIGH, val)
-#define bfin_read_USB_DMA1COUNTLOW() bfin_read16(USB_DMA1COUNTLOW)
-#define bfin_write_USB_DMA1COUNTLOW(val) bfin_write16(USB_DMA1COUNTLOW, val)
-#define bfin_read_USB_DMA1COUNTHIGH() bfin_read16(USB_DMA1COUNTHIGH)
-#define bfin_write_USB_DMA1COUNTHIGH(val) bfin_write16(USB_DMA1COUNTHIGH, val)
-
-/* USB Channel 2 Config Registers */
-
-#define bfin_read_USB_DMA2CONTROL() bfin_read16(USB_DMA2CONTROL)
-#define bfin_write_USB_DMA2CONTROL(val) bfin_write16(USB_DMA2CONTROL, val)
-#define bfin_read_USB_DMA2ADDRLOW() bfin_read16(USB_DMA2ADDRLOW)
-#define bfin_write_USB_DMA2ADDRLOW(val) bfin_write16(USB_DMA2ADDRLOW, val)
-#define bfin_read_USB_DMA2ADDRHIGH() bfin_read16(USB_DMA2ADDRHIGH)
-#define bfin_write_USB_DMA2ADDRHIGH(val) bfin_write16(USB_DMA2ADDRHIGH, val)
-#define bfin_read_USB_DMA2COUNTLOW() bfin_read16(USB_DMA2COUNTLOW)
-#define bfin_write_USB_DMA2COUNTLOW(val) bfin_write16(USB_DMA2COUNTLOW, val)
-#define bfin_read_USB_DMA2COUNTHIGH() bfin_read16(USB_DMA2COUNTHIGH)
-#define bfin_write_USB_DMA2COUNTHIGH(val) bfin_write16(USB_DMA2COUNTHIGH, val)
-
-/* USB Channel 3 Config Registers */
-
-#define bfin_read_USB_DMA3CONTROL() bfin_read16(USB_DMA3CONTROL)
-#define bfin_write_USB_DMA3CONTROL(val) bfin_write16(USB_DMA3CONTROL, val)
-#define bfin_read_USB_DMA3ADDRLOW() bfin_read16(USB_DMA3ADDRLOW)
-#define bfin_write_USB_DMA3ADDRLOW(val) bfin_write16(USB_DMA3ADDRLOW, val)
-#define bfin_read_USB_DMA3ADDRHIGH() bfin_read16(USB_DMA3ADDRHIGH)
-#define bfin_write_USB_DMA3ADDRHIGH(val) bfin_write16(USB_DMA3ADDRHIGH, val)
-#define bfin_read_USB_DMA3COUNTLOW() bfin_read16(USB_DMA3COUNTLOW)
-#define bfin_write_USB_DMA3COUNTLOW(val) bfin_write16(USB_DMA3COUNTLOW, val)
-#define bfin_read_USB_DMA3COUNTHIGH() bfin_read16(USB_DMA3COUNTHIGH)
-#define bfin_write_USB_DMA3COUNTHIGH(val) bfin_write16(USB_DMA3COUNTHIGH, val)
-
-/* USB Channel 4 Config Registers */
-
-#define bfin_read_USB_DMA4CONTROL() bfin_read16(USB_DMA4CONTROL)
-#define bfin_write_USB_DMA4CONTROL(val) bfin_write16(USB_DMA4CONTROL, val)
-#define bfin_read_USB_DMA4ADDRLOW() bfin_read16(USB_DMA4ADDRLOW)
-#define bfin_write_USB_DMA4ADDRLOW(val) bfin_write16(USB_DMA4ADDRLOW, val)
-#define bfin_read_USB_DMA4ADDRHIGH() bfin_read16(USB_DMA4ADDRHIGH)
-#define bfin_write_USB_DMA4ADDRHIGH(val) bfin_write16(USB_DMA4ADDRHIGH, val)
-#define bfin_read_USB_DMA4COUNTLOW() bfin_read16(USB_DMA4COUNTLOW)
-#define bfin_write_USB_DMA4COUNTLOW(val) bfin_write16(USB_DMA4COUNTLOW, val)
-#define bfin_read_USB_DMA4COUNTHIGH() bfin_read16(USB_DMA4COUNTHIGH)
-#define bfin_write_USB_DMA4COUNTHIGH(val) bfin_write16(USB_DMA4COUNTHIGH, val)
-
-/* USB Channel 5 Config Registers */
-
-#define bfin_read_USB_DMA5CONTROL() bfin_read16(USB_DMA5CONTROL)
-#define bfin_write_USB_DMA5CONTROL(val) bfin_write16(USB_DMA5CONTROL, val)
-#define bfin_read_USB_DMA5ADDRLOW() bfin_read16(USB_DMA5ADDRLOW)
-#define bfin_write_USB_DMA5ADDRLOW(val) bfin_write16(USB_DMA5ADDRLOW, val)
-#define bfin_read_USB_DMA5ADDRHIGH() bfin_read16(USB_DMA5ADDRHIGH)
-#define bfin_write_USB_DMA5ADDRHIGH(val) bfin_write16(USB_DMA5ADDRHIGH, val)
-#define bfin_read_USB_DMA5COUNTLOW() bfin_read16(USB_DMA5COUNTLOW)
-#define bfin_write_USB_DMA5COUNTLOW(val) bfin_write16(USB_DMA5COUNTLOW, val)
-#define bfin_read_USB_DMA5COUNTHIGH() bfin_read16(USB_DMA5COUNTHIGH)
-#define bfin_write_USB_DMA5COUNTHIGH(val) bfin_write16(USB_DMA5COUNTHIGH, val)
-
-/* USB Channel 6 Config Registers */
-
-#define bfin_read_USB_DMA6CONTROL() bfin_read16(USB_DMA6CONTROL)
-#define bfin_write_USB_DMA6CONTROL(val) bfin_write16(USB_DMA6CONTROL, val)
-#define bfin_read_USB_DMA6ADDRLOW() bfin_read16(USB_DMA6ADDRLOW)
-#define bfin_write_USB_DMA6ADDRLOW(val) bfin_write16(USB_DMA6ADDRLOW, val)
-#define bfin_read_USB_DMA6ADDRHIGH() bfin_read16(USB_DMA6ADDRHIGH)
-#define bfin_write_USB_DMA6ADDRHIGH(val) bfin_write16(USB_DMA6ADDRHIGH, val)
-#define bfin_read_USB_DMA6COUNTLOW() bfin_read16(USB_DMA6COUNTLOW)
-#define bfin_write_USB_DMA6COUNTLOW(val) bfin_write16(USB_DMA6COUNTLOW, val)
-#define bfin_read_USB_DMA6COUNTHIGH() bfin_read16(USB_DMA6COUNTHIGH)
-#define bfin_write_USB_DMA6COUNTHIGH(val) bfin_write16(USB_DMA6COUNTHIGH, val)
-
-/* USB Channel 7 Config Registers */
-
-#define bfin_read_USB_DMA7CONTROL() bfin_read16(USB_DMA7CONTROL)
-#define bfin_write_USB_DMA7CONTROL(val) bfin_write16(USB_DMA7CONTROL, val)
-#define bfin_read_USB_DMA7ADDRLOW() bfin_read16(USB_DMA7ADDRLOW)
-#define bfin_write_USB_DMA7ADDRLOW(val) bfin_write16(USB_DMA7ADDRLOW, val)
-#define bfin_read_USB_DMA7ADDRHIGH() bfin_read16(USB_DMA7ADDRHIGH)
-#define bfin_write_USB_DMA7ADDRHIGH(val) bfin_write16(USB_DMA7ADDRHIGH, val)
-#define bfin_read_USB_DMA7COUNTLOW() bfin_read16(USB_DMA7COUNTLOW)
-#define bfin_write_USB_DMA7COUNTLOW(val) bfin_write16(USB_DMA7COUNTLOW, val)
-#define bfin_read_USB_DMA7COUNTHIGH() bfin_read16(USB_DMA7COUNTHIGH)
-#define bfin_write_USB_DMA7COUNTHIGH(val) bfin_write16(USB_DMA7COUNTHIGH, val)
-
#endif /* _CDEF_BF527_H */
#ifndef _DEF_BF527_H
#define _DEF_BF527_H
-/* Include all Core registers and bit definitions */
-#include <asm/def_LPBlackfin.h>
+/* BF527 is BF525 + EMAC */
+#include "defBF525.h"
-/* SYSTEM & MMR ADDRESS DEFINITIONS FOR ADSP-BF527 */
-
-/* Include defBF52x_base.h for the set of #defines that are common to all ADSP-BF52x processors */
-#include "defBF52x_base.h"
-
-/* The following are the #defines needed by ADSP-BF527 that are not in the common header */
/* 10/100 Ethernet Controller (0xFFC03000 - 0xFFC031FF) */
#define EMAC_OPMODE 0xFFC03000 /* Operating Mode Register */
#define TX_GE1024_CNT 0x00200000 /* 1024-Max-Byte TX Frames Sent */
#define TX_ABORT_CNT 0x00400000 /* TX Frames Aborted */
-/* USB Control Registers */
-
-#define USB_FADDR 0xffc03800 /* Function address register */
-#define USB_POWER 0xffc03804 /* Power management register */
-#define USB_INTRTX 0xffc03808 /* Interrupt register for endpoint 0 and Tx endpoint 1 to 7 */
-#define USB_INTRRX 0xffc0380c /* Interrupt register for Rx endpoints 1 to 7 */
-#define USB_INTRTXE 0xffc03810 /* Interrupt enable register for IntrTx */
-#define USB_INTRRXE 0xffc03814 /* Interrupt enable register for IntrRx */
-#define USB_INTRUSB 0xffc03818 /* Interrupt register for common USB interrupts */
-#define USB_INTRUSBE 0xffc0381c /* Interrupt enable register for IntrUSB */
-#define USB_FRAME 0xffc03820 /* USB frame number */
-#define USB_INDEX 0xffc03824 /* Index register for selecting the indexed endpoint registers */
-#define USB_TESTMODE 0xffc03828 /* Enabled USB 20 test modes */
-#define USB_GLOBINTR 0xffc0382c /* Global Interrupt Mask register and Wakeup Exception Interrupt */
-#define USB_GLOBAL_CTL 0xffc03830 /* Global Clock Control for the core */
-
-/* USB Packet Control Registers */
-
-#define USB_TX_MAX_PACKET 0xffc03840 /* Maximum packet size for Host Tx endpoint */
-#define USB_CSR0 0xffc03844 /* Control Status register for endpoint 0 and Control Status register for Host Tx endpoint */
-#define USB_TXCSR 0xffc03844 /* Control Status register for endpoint 0 and Control Status register for Host Tx endpoint */
-#define USB_RX_MAX_PACKET 0xffc03848 /* Maximum packet size for Host Rx endpoint */
-#define USB_RXCSR 0xffc0384c /* Control Status register for Host Rx endpoint */
-#define USB_COUNT0 0xffc03850 /* Number of bytes received in endpoint 0 FIFO and Number of bytes received in Host Tx endpoint */
-#define USB_RXCOUNT 0xffc03850 /* Number of bytes received in endpoint 0 FIFO and Number of bytes received in Host Tx endpoint */
-#define USB_TXTYPE 0xffc03854 /* Sets the transaction protocol and peripheral endpoint number for the Host Tx endpoint */
-#define USB_NAKLIMIT0 0xffc03858 /* Sets the NAK response timeout on Endpoint 0 and on Bulk transfers for Host Tx endpoint */
-#define USB_TXINTERVAL 0xffc03858 /* Sets the NAK response timeout on Endpoint 0 and on Bulk transfers for Host Tx endpoint */
-#define USB_RXTYPE 0xffc0385c /* Sets the transaction protocol and peripheral endpoint number for the Host Rx endpoint */
-#define USB_RXINTERVAL 0xffc03860 /* Sets the polling interval for Interrupt and Isochronous transfers or the NAK response timeout on Bulk transfers */
-#define USB_TXCOUNT 0xffc03868 /* Number of bytes to be written to the selected endpoint Tx FIFO */
-
-/* USB Endpoint FIFO Registers */
-
-#define USB_EP0_FIFO 0xffc03880 /* Endpoint 0 FIFO */
-#define USB_EP1_FIFO 0xffc03888 /* Endpoint 1 FIFO */
-#define USB_EP2_FIFO 0xffc03890 /* Endpoint 2 FIFO */
-#define USB_EP3_FIFO 0xffc03898 /* Endpoint 3 FIFO */
-#define USB_EP4_FIFO 0xffc038a0 /* Endpoint 4 FIFO */
-#define USB_EP5_FIFO 0xffc038a8 /* Endpoint 5 FIFO */
-#define USB_EP6_FIFO 0xffc038b0 /* Endpoint 6 FIFO */
-#define USB_EP7_FIFO 0xffc038b8 /* Endpoint 7 FIFO */
-
-/* USB OTG Control Registers */
-
-#define USB_OTG_DEV_CTL 0xffc03900 /* OTG Device Control Register */
-#define USB_OTG_VBUS_IRQ 0xffc03904 /* OTG VBUS Control Interrupts */
-#define USB_OTG_VBUS_MASK 0xffc03908 /* VBUS Control Interrupt Enable */
-
-/* USB Phy Control Registers */
-
-#define USB_LINKINFO 0xffc03948 /* Enables programming of some PHY-side delays */
-#define USB_VPLEN 0xffc0394c /* Determines duration of VBUS pulse for VBUS charging */
-#define USB_HS_EOF1 0xffc03950 /* Time buffer for High-Speed transactions */
-#define USB_FS_EOF1 0xffc03954 /* Time buffer for Full-Speed transactions */
-#define USB_LS_EOF1 0xffc03958 /* Time buffer for Low-Speed transactions */
-
-/* (APHY_CNTRL is for ADI usage only) */
-
-#define USB_APHY_CNTRL 0xffc039e0 /* Register that increases visibility of Analog PHY */
-
-/* (APHY_CALIB is for ADI usage only) */
-
-#define USB_APHY_CALIB 0xffc039e4 /* Register used to set some calibration values */
-
-#define USB_APHY_CNTRL2 0xffc039e8 /* Register used to prevent re-enumeration once Moab goes into hibernate mode */
-
-/* (PHY_TEST is for ADI usage only) */
-
-#define USB_PHY_TEST 0xffc039ec /* Used for reducing simulation time and simplifies FIFO testability */
-
-#define USB_PLLOSC_CTRL 0xffc039f0 /* Used to program different parameters for USB PLL and Oscillator */
-#define USB_SRP_CLKDIV 0xffc039f4 /* Used to program clock divide value for the clock fed to the SRP detection logic */
-
-/* USB Endpoint 0 Control Registers */
-
-#define USB_EP_NI0_TXMAXP 0xffc03a00 /* Maximum packet size for Host Tx endpoint0 */
-#define USB_EP_NI0_TXCSR 0xffc03a04 /* Control Status register for endpoint 0 */
-#define USB_EP_NI0_RXMAXP 0xffc03a08 /* Maximum packet size for Host Rx endpoint0 */
-#define USB_EP_NI0_RXCSR 0xffc03a0c /* Control Status register for Host Rx endpoint0 */
-#define USB_EP_NI0_RXCOUNT 0xffc03a10 /* Number of bytes received in endpoint 0 FIFO */
-#define USB_EP_NI0_TXTYPE 0xffc03a14 /* Sets the transaction protocol and peripheral endpoint number for the Host Tx endpoint0 */
-#define USB_EP_NI0_TXINTERVAL 0xffc03a18 /* Sets the NAK response timeout on Endpoint 0 */
-#define USB_EP_NI0_RXTYPE 0xffc03a1c /* Sets the transaction protocol and peripheral endpoint number for the Host Rx endpoint0 */
-#define USB_EP_NI0_RXINTERVAL 0xffc03a20 /* Sets the polling interval for Interrupt/Isochronous transfers or the NAK response timeout on Bulk transfers for Host Rx endpoint0 */
-#define USB_EP_NI0_TXCOUNT 0xffc03a28 /* Number of bytes to be written to the endpoint0 Tx FIFO */
-
-/* USB Endpoint 1 Control Registers */
-
-#define USB_EP_NI1_TXMAXP 0xffc03a40 /* Maximum packet size for Host Tx endpoint1 */
-#define USB_EP_NI1_TXCSR 0xffc03a44 /* Control Status register for endpoint1 */
-#define USB_EP_NI1_RXMAXP 0xffc03a48 /* Maximum packet size for Host Rx endpoint1 */
-#define USB_EP_NI1_RXCSR 0xffc03a4c /* Control Status register for Host Rx endpoint1 */
-#define USB_EP_NI1_RXCOUNT 0xffc03a50 /* Number of bytes received in endpoint1 FIFO */
-#define USB_EP_NI1_TXTYPE 0xffc03a54 /* Sets the transaction protocol and peripheral endpoint number for the Host Tx endpoint1 */
-#define USB_EP_NI1_TXINTERVAL 0xffc03a58 /* Sets the NAK response timeout on Endpoint1 */
-#define USB_EP_NI1_RXTYPE 0xffc03a5c /* Sets the transaction protocol and peripheral endpoint number for the Host Rx endpoint1 */
-#define USB_EP_NI1_RXINTERVAL 0xffc03a60 /* Sets the polling interval for Interrupt/Isochronous transfers or the NAK response timeout on Bulk transfers for Host Rx endpoint1 */
-#define USB_EP_NI1_TXCOUNT 0xffc03a68 /* Number of bytes to be written to the+H102 endpoint1 Tx FIFO */
-
-/* USB Endpoint 2 Control Registers */
-
-#define USB_EP_NI2_TXMAXP 0xffc03a80 /* Maximum packet size for Host Tx endpoint2 */
-#define USB_EP_NI2_TXCSR 0xffc03a84 /* Control Status register for endpoint2 */
-#define USB_EP_NI2_RXMAXP 0xffc03a88 /* Maximum packet size for Host Rx endpoint2 */
-#define USB_EP_NI2_RXCSR 0xffc03a8c /* Control Status register for Host Rx endpoint2 */
-#define USB_EP_NI2_RXCOUNT 0xffc03a90 /* Number of bytes received in endpoint2 FIFO */
-#define USB_EP_NI2_TXTYPE 0xffc03a94 /* Sets the transaction protocol and peripheral endpoint number for the Host Tx endpoint2 */
-#define USB_EP_NI2_TXINTERVAL 0xffc03a98 /* Sets the NAK response timeout on Endpoint2 */
-#define USB_EP_NI2_RXTYPE 0xffc03a9c /* Sets the transaction protocol and peripheral endpoint number for the Host Rx endpoint2 */
-#define USB_EP_NI2_RXINTERVAL 0xffc03aa0 /* Sets the polling interval for Interrupt/Isochronous transfers or the NAK response timeout on Bulk transfers for Host Rx endpoint2 */
-#define USB_EP_NI2_TXCOUNT 0xffc03aa8 /* Number of bytes to be written to the endpoint2 Tx FIFO */
-
-/* USB Endpoint 3 Control Registers */
-
-#define USB_EP_NI3_TXMAXP 0xffc03ac0 /* Maximum packet size for Host Tx endpoint3 */
-#define USB_EP_NI3_TXCSR 0xffc03ac4 /* Control Status register for endpoint3 */
-#define USB_EP_NI3_RXMAXP 0xffc03ac8 /* Maximum packet size for Host Rx endpoint3 */
-#define USB_EP_NI3_RXCSR 0xffc03acc /* Control Status register for Host Rx endpoint3 */
-#define USB_EP_NI3_RXCOUNT 0xffc03ad0 /* Number of bytes received in endpoint3 FIFO */
-#define USB_EP_NI3_TXTYPE 0xffc03ad4 /* Sets the transaction protocol and peripheral endpoint number for the Host Tx endpoint3 */
-#define USB_EP_NI3_TXINTERVAL 0xffc03ad8 /* Sets the NAK response timeout on Endpoint3 */
-#define USB_EP_NI3_RXTYPE 0xffc03adc /* Sets the transaction protocol and peripheral endpoint number for the Host Rx endpoint3 */
-#define USB_EP_NI3_RXINTERVAL 0xffc03ae0 /* Sets the polling interval for Interrupt/Isochronous transfers or the NAK response timeout on Bulk transfers for Host Rx endpoint3 */
-#define USB_EP_NI3_TXCOUNT 0xffc03ae8 /* Number of bytes to be written to the H124endpoint3 Tx FIFO */
-
-/* USB Endpoint 4 Control Registers */
-
-#define USB_EP_NI4_TXMAXP 0xffc03b00 /* Maximum packet size for Host Tx endpoint4 */
-#define USB_EP_NI4_TXCSR 0xffc03b04 /* Control Status register for endpoint4 */
-#define USB_EP_NI4_RXMAXP 0xffc03b08 /* Maximum packet size for Host Rx endpoint4 */
-#define USB_EP_NI4_RXCSR 0xffc03b0c /* Control Status register for Host Rx endpoint4 */
-#define USB_EP_NI4_RXCOUNT 0xffc03b10 /* Number of bytes received in endpoint4 FIFO */
-#define USB_EP_NI4_TXTYPE 0xffc03b14 /* Sets the transaction protocol and peripheral endpoint number for the Host Tx endpoint4 */
-#define USB_EP_NI4_TXINTERVAL 0xffc03b18 /* Sets the NAK response timeout on Endpoint4 */
-#define USB_EP_NI4_RXTYPE 0xffc03b1c /* Sets the transaction protocol and peripheral endpoint number for the Host Rx endpoint4 */
-#define USB_EP_NI4_RXINTERVAL 0xffc03b20 /* Sets the polling interval for Interrupt/Isochronous transfers or the NAK response timeout on Bulk transfers for Host Rx endpoint4 */
-#define USB_EP_NI4_TXCOUNT 0xffc03b28 /* Number of bytes to be written to the endpoint4 Tx FIFO */
-
-/* USB Endpoint 5 Control Registers */
-
-#define USB_EP_NI5_TXMAXP 0xffc03b40 /* Maximum packet size for Host Tx endpoint5 */
-#define USB_EP_NI5_TXCSR 0xffc03b44 /* Control Status register for endpoint5 */
-#define USB_EP_NI5_RXMAXP 0xffc03b48 /* Maximum packet size for Host Rx endpoint5 */
-#define USB_EP_NI5_RXCSR 0xffc03b4c /* Control Status register for Host Rx endpoint5 */
-#define USB_EP_NI5_RXCOUNT 0xffc03b50 /* Number of bytes received in endpoint5 FIFO */
-#define USB_EP_NI5_TXTYPE 0xffc03b54 /* Sets the transaction protocol and peripheral endpoint number for the Host Tx endpoint5 */
-#define USB_EP_NI5_TXINTERVAL 0xffc03b58 /* Sets the NAK response timeout on Endpoint5 */
-#define USB_EP_NI5_RXTYPE 0xffc03b5c /* Sets the transaction protocol and peripheral endpoint number for the Host Rx endpoint5 */
-#define USB_EP_NI5_RXINTERVAL 0xffc03b60 /* Sets the polling interval for Interrupt/Isochronous transfers or the NAK response timeout on Bulk transfers for Host Rx endpoint5 */
-#define USB_EP_NI5_TXCOUNT 0xffc03b68 /* Number of bytes to be written to the endpoint5 Tx FIFO */
-
-/* USB Endpoint 6 Control Registers */
-
-#define USB_EP_NI6_TXMAXP 0xffc03b80 /* Maximum packet size for Host Tx endpoint6 */
-#define USB_EP_NI6_TXCSR 0xffc03b84 /* Control Status register for endpoint6 */
-#define USB_EP_NI6_RXMAXP 0xffc03b88 /* Maximum packet size for Host Rx endpoint6 */
-#define USB_EP_NI6_RXCSR 0xffc03b8c /* Control Status register for Host Rx endpoint6 */
-#define USB_EP_NI6_RXCOUNT 0xffc03b90 /* Number of bytes received in endpoint6 FIFO */
-#define USB_EP_NI6_TXTYPE 0xffc03b94 /* Sets the transaction protocol and peripheral endpoint number for the Host Tx endpoint6 */
-#define USB_EP_NI6_TXINTERVAL 0xffc03b98 /* Sets the NAK response timeout on Endpoint6 */
-#define USB_EP_NI6_RXTYPE 0xffc03b9c /* Sets the transaction protocol and peripheral endpoint number for the Host Rx endpoint6 */
-#define USB_EP_NI6_RXINTERVAL 0xffc03ba0 /* Sets the polling interval for Interrupt/Isochronous transfers or the NAK response timeout on Bulk transfers for Host Rx endpoint6 */
-#define USB_EP_NI6_TXCOUNT 0xffc03ba8 /* Number of bytes to be written to the endpoint6 Tx FIFO */
-
-/* USB Endpoint 7 Control Registers */
-
-#define USB_EP_NI7_TXMAXP 0xffc03bc0 /* Maximum packet size for Host Tx endpoint7 */
-#define USB_EP_NI7_TXCSR 0xffc03bc4 /* Control Status register for endpoint7 */
-#define USB_EP_NI7_RXMAXP 0xffc03bc8 /* Maximum packet size for Host Rx endpoint7 */
-#define USB_EP_NI7_RXCSR 0xffc03bcc /* Control Status register for Host Rx endpoint7 */
-#define USB_EP_NI7_RXCOUNT 0xffc03bd0 /* Number of bytes received in endpoint7 FIFO */
-#define USB_EP_NI7_TXTYPE 0xffc03bd4 /* Sets the transaction protocol and peripheral endpoint number for the Host Tx endpoint7 */
-#define USB_EP_NI7_TXINTERVAL 0xffc03bd8 /* Sets the NAK response timeout on Endpoint7 */
-#define USB_EP_NI7_RXTYPE 0xffc03bdc /* Sets the transaction protocol and peripheral endpoint number for the Host Rx endpoint7 */
-#define USB_EP_NI7_RXINTERVAL 0xffc03bf0 /* Sets the polling interval for Interrupt/Isochronous transfers or the NAK response timeout on Bulk transfers for Host Rx endpoint7 */
-#define USB_EP_NI7_TXCOUNT 0xffc03bf8 /* Number of bytes to be written to the endpoint7 Tx FIFO */
-
-#define USB_DMA_INTERRUPT 0xffc03c00 /* Indicates pending interrupts for the DMA channels */
-
-/* USB Channel 0 Config Registers */
-
-#define USB_DMA0CONTROL 0xffc03c04 /* DMA master channel 0 configuration */
-#define USB_DMA0ADDRLOW 0xffc03c08 /* Lower 16-bits of memory source/destination address for DMA master channel 0 */
-#define USB_DMA0ADDRHIGH 0xffc03c0c /* Upper 16-bits of memory source/destination address for DMA master channel 0 */
-#define USB_DMA0COUNTLOW 0xffc03c10 /* Lower 16-bits of byte count of DMA transfer for DMA master channel 0 */
-#define USB_DMA0COUNTHIGH 0xffc03c14 /* Upper 16-bits of byte count of DMA transfer for DMA master channel 0 */
-
-/* USB Channel 1 Config Registers */
-
-#define USB_DMA1CONTROL 0xffc03c24 /* DMA master channel 1 configuration */
-#define USB_DMA1ADDRLOW 0xffc03c28 /* Lower 16-bits of memory source/destination address for DMA master channel 1 */
-#define USB_DMA1ADDRHIGH 0xffc03c2c /* Upper 16-bits of memory source/destination address for DMA master channel 1 */
-#define USB_DMA1COUNTLOW 0xffc03c30 /* Lower 16-bits of byte count of DMA transfer for DMA master channel 1 */
-#define USB_DMA1COUNTHIGH 0xffc03c34 /* Upper 16-bits of byte count of DMA transfer for DMA master channel 1 */
-
-/* USB Channel 2 Config Registers */
-
-#define USB_DMA2CONTROL 0xffc03c44 /* DMA master channel 2 configuration */
-#define USB_DMA2ADDRLOW 0xffc03c48 /* Lower 16-bits of memory source/destination address for DMA master channel 2 */
-#define USB_DMA2ADDRHIGH 0xffc03c4c /* Upper 16-bits of memory source/destination address for DMA master channel 2 */
-#define USB_DMA2COUNTLOW 0xffc03c50 /* Lower 16-bits of byte count of DMA transfer for DMA master channel 2 */
-#define USB_DMA2COUNTHIGH 0xffc03c54 /* Upper 16-bits of byte count of DMA transfer for DMA master channel 2 */
-
-/* USB Channel 3 Config Registers */
-
-#define USB_DMA3CONTROL 0xffc03c64 /* DMA master channel 3 configuration */
-#define USB_DMA3ADDRLOW 0xffc03c68 /* Lower 16-bits of memory source/destination address for DMA master channel 3 */
-#define USB_DMA3ADDRHIGH 0xffc03c6c /* Upper 16-bits of memory source/destination address for DMA master channel 3 */
-#define USB_DMA3COUNTLOW 0xffc03c70 /* Lower 16-bits of byte count of DMA transfer for DMA master channel 3 */
-#define USB_DMA3COUNTHIGH 0xffc03c74 /* Upper 16-bits of byte count of DMA transfer for DMA master channel 3 */
-
-/* USB Channel 4 Config Registers */
-
-#define USB_DMA4CONTROL 0xffc03c84 /* DMA master channel 4 configuration */
-#define USB_DMA4ADDRLOW 0xffc03c88 /* Lower 16-bits of memory source/destination address for DMA master channel 4 */
-#define USB_DMA4ADDRHIGH 0xffc03c8c /* Upper 16-bits of memory source/destination address for DMA master channel 4 */
-#define USB_DMA4COUNTLOW 0xffc03c90 /* Lower 16-bits of byte count of DMA transfer for DMA master channel 4 */
-#define USB_DMA4COUNTHIGH 0xffc03c94 /* Upper 16-bits of byte count of DMA transfer for DMA master channel 4 */
-
-/* USB Channel 5 Config Registers */
-
-#define USB_DMA5CONTROL 0xffc03ca4 /* DMA master channel 5 configuration */
-#define USB_DMA5ADDRLOW 0xffc03ca8 /* Lower 16-bits of memory source/destination address for DMA master channel 5 */
-#define USB_DMA5ADDRHIGH 0xffc03cac /* Upper 16-bits of memory source/destination address for DMA master channel 5 */
-#define USB_DMA5COUNTLOW 0xffc03cb0 /* Lower 16-bits of byte count of DMA transfer for DMA master channel 5 */
-#define USB_DMA5COUNTHIGH 0xffc03cb4 /* Upper 16-bits of byte count of DMA transfer for DMA master channel 5 */
-
-/* USB Channel 6 Config Registers */
-
-#define USB_DMA6CONTROL 0xffc03cc4 /* DMA master channel 6 configuration */
-#define USB_DMA6ADDRLOW 0xffc03cc8 /* Lower 16-bits of memory source/destination address for DMA master channel 6 */
-#define USB_DMA6ADDRHIGH 0xffc03ccc /* Upper 16-bits of memory source/destination address for DMA master channel 6 */
-#define USB_DMA6COUNTLOW 0xffc03cd0 /* Lower 16-bits of byte count of DMA transfer for DMA master channel 6 */
-#define USB_DMA6COUNTHIGH 0xffc03cd4 /* Upper 16-bits of byte count of DMA transfer for DMA master channel 6 */
-
-/* USB Channel 7 Config Registers */
-
-#define USB_DMA7CONTROL 0xffc03ce4 /* DMA master channel 7 configuration */
-#define USB_DMA7ADDRLOW 0xffc03ce8 /* Lower 16-bits of memory source/destination address for DMA master channel 7 */
-#define USB_DMA7ADDRHIGH 0xffc03cec /* Upper 16-bits of memory source/destination address for DMA master channel 7 */
-#define USB_DMA7COUNTLOW 0xffc03cf0 /* Lower 16-bits of byte count of DMA transfer for DMA master channel 7 */
-#define USB_DMA7COUNTHIGH 0xffc03cf4 /* Upper 16-bits of byte count of DMA transfer for DMA master channel 7 */
-
-/* Bit masks for USB_FADDR */
-
-#define FUNCTION_ADDRESS 0x7f /* Function address */
-
-/* Bit masks for USB_POWER */
-
-#define ENABLE_SUSPENDM 0x1 /* enable SuspendM output */
-#define nENABLE_SUSPENDM 0x0
-#define SUSPEND_MODE 0x2 /* Suspend Mode indicator */
-#define nSUSPEND_MODE 0x0
-#define RESUME_MODE 0x4 /* DMA Mode */
-#define nRESUME_MODE 0x0
-#define RESET 0x8 /* Reset indicator */
-#define nRESET 0x0
-#define HS_MODE 0x10 /* High Speed mode indicator */
-#define nHS_MODE 0x0
-#define HS_ENABLE 0x20 /* high Speed Enable */
-#define nHS_ENABLE 0x0
-#define SOFT_CONN 0x40 /* Soft connect */
-#define nSOFT_CONN 0x0
-#define ISO_UPDATE 0x80 /* Isochronous update */
-#define nISO_UPDATE 0x0
-
-/* Bit masks for USB_INTRTX */
-
-#define EP0_TX 0x1 /* Tx Endpoint 0 interrupt */
-#define nEP0_TX 0x0
-#define EP1_TX 0x2 /* Tx Endpoint 1 interrupt */
-#define nEP1_TX 0x0
-#define EP2_TX 0x4 /* Tx Endpoint 2 interrupt */
-#define nEP2_TX 0x0
-#define EP3_TX 0x8 /* Tx Endpoint 3 interrupt */
-#define nEP3_TX 0x0
-#define EP4_TX 0x10 /* Tx Endpoint 4 interrupt */
-#define nEP4_TX 0x0
-#define EP5_TX 0x20 /* Tx Endpoint 5 interrupt */
-#define nEP5_TX 0x0
-#define EP6_TX 0x40 /* Tx Endpoint 6 interrupt */
-#define nEP6_TX 0x0
-#define EP7_TX 0x80 /* Tx Endpoint 7 interrupt */
-#define nEP7_TX 0x0
-
-/* Bit masks for USB_INTRRX */
-
-#define EP1_RX 0x2 /* Rx Endpoint 1 interrupt */
-#define nEP1_RX 0x0
-#define EP2_RX 0x4 /* Rx Endpoint 2 interrupt */
-#define nEP2_RX 0x0
-#define EP3_RX 0x8 /* Rx Endpoint 3 interrupt */
-#define nEP3_RX 0x0
-#define EP4_RX 0x10 /* Rx Endpoint 4 interrupt */
-#define nEP4_RX 0x0
-#define EP5_RX 0x20 /* Rx Endpoint 5 interrupt */
-#define nEP5_RX 0x0
-#define EP6_RX 0x40 /* Rx Endpoint 6 interrupt */
-#define nEP6_RX 0x0
-#define EP7_RX 0x80 /* Rx Endpoint 7 interrupt */
-#define nEP7_RX 0x0
-
-/* Bit masks for USB_INTRTXE */
-
-#define EP0_TX_E 0x1 /* Endpoint 0 interrupt Enable */
-#define nEP0_TX_E 0x0
-#define EP1_TX_E 0x2 /* Tx Endpoint 1 interrupt Enable */
-#define nEP1_TX_E 0x0
-#define EP2_TX_E 0x4 /* Tx Endpoint 2 interrupt Enable */
-#define nEP2_TX_E 0x0
-#define EP3_TX_E 0x8 /* Tx Endpoint 3 interrupt Enable */
-#define nEP3_TX_E 0x0
-#define EP4_TX_E 0x10 /* Tx Endpoint 4 interrupt Enable */
-#define nEP4_TX_E 0x0
-#define EP5_TX_E 0x20 /* Tx Endpoint 5 interrupt Enable */
-#define nEP5_TX_E 0x0
-#define EP6_TX_E 0x40 /* Tx Endpoint 6 interrupt Enable */
-#define nEP6_TX_E 0x0
-#define EP7_TX_E 0x80 /* Tx Endpoint 7 interrupt Enable */
-#define nEP7_TX_E 0x0
-
-/* Bit masks for USB_INTRRXE */
-
-#define EP1_RX_E 0x2 /* Rx Endpoint 1 interrupt Enable */
-#define nEP1_RX_E 0x0
-#define EP2_RX_E 0x4 /* Rx Endpoint 2 interrupt Enable */
-#define nEP2_RX_E 0x0
-#define EP3_RX_E 0x8 /* Rx Endpoint 3 interrupt Enable */
-#define nEP3_RX_E 0x0
-#define EP4_RX_E 0x10 /* Rx Endpoint 4 interrupt Enable */
-#define nEP4_RX_E 0x0
-#define EP5_RX_E 0x20 /* Rx Endpoint 5 interrupt Enable */
-#define nEP5_RX_E 0x0
-#define EP6_RX_E 0x40 /* Rx Endpoint 6 interrupt Enable */
-#define nEP6_RX_E 0x0
-#define EP7_RX_E 0x80 /* Rx Endpoint 7 interrupt Enable */
-#define nEP7_RX_E 0x0
-
-/* Bit masks for USB_INTRUSB */
-
-#define SUSPEND_B 0x1 /* Suspend indicator */
-#define nSUSPEND_B 0x0
-#define RESUME_B 0x2 /* Resume indicator */
-#define nRESUME_B 0x0
-#define RESET_OR_BABLE_B 0x4 /* Reset/babble indicator */
-#define nRESET_OR_BABLE_B 0x0
-#define SOF_B 0x8 /* Start of frame */
-#define nSOF_B 0x0
-#define CONN_B 0x10 /* Connection indicator */
-#define nCONN_B 0x0
-#define DISCON_B 0x20 /* Disconnect indicator */
-#define nDISCON_B 0x0
-#define SESSION_REQ_B 0x40 /* Session Request */
-#define nSESSION_REQ_B 0x0
-#define VBUS_ERROR_B 0x80 /* Vbus threshold indicator */
-#define nVBUS_ERROR_B 0x0
-
-/* Bit masks for USB_INTRUSBE */
-
-#define SUSPEND_BE 0x1 /* Suspend indicator int enable */
-#define nSUSPEND_BE 0x0
-#define RESUME_BE 0x2 /* Resume indicator int enable */
-#define nRESUME_BE 0x0
-#define RESET_OR_BABLE_BE 0x4 /* Reset/babble indicator int enable */
-#define nRESET_OR_BABLE_BE 0x0
-#define SOF_BE 0x8 /* Start of frame int enable */
-#define nSOF_BE 0x0
-#define CONN_BE 0x10 /* Connection indicator int enable */
-#define nCONN_BE 0x0
-#define DISCON_BE 0x20 /* Disconnect indicator int enable */
-#define nDISCON_BE 0x0
-#define SESSION_REQ_BE 0x40 /* Session Request int enable */
-#define nSESSION_REQ_BE 0x0
-#define VBUS_ERROR_BE 0x80 /* Vbus threshold indicator int enable */
-#define nVBUS_ERROR_BE 0x0
-
-/* Bit masks for USB_FRAME */
-
-#define FRAME_NUMBER 0x7ff /* Frame number */
-
-/* Bit masks for USB_INDEX */
-
-#define SELECTED_ENDPOINT 0xf /* selected endpoint */
-
-/* Bit masks for USB_GLOBAL_CTL */
-
-#define GLOBAL_ENA 0x1 /* enables USB module */
-#define nGLOBAL_ENA 0x0
-#define EP1_TX_ENA 0x2 /* Transmit endpoint 1 enable */
-#define nEP1_TX_ENA 0x0
-#define EP2_TX_ENA 0x4 /* Transmit endpoint 2 enable */
-#define nEP2_TX_ENA 0x0
-#define EP3_TX_ENA 0x8 /* Transmit endpoint 3 enable */
-#define nEP3_TX_ENA 0x0
-#define EP4_TX_ENA 0x10 /* Transmit endpoint 4 enable */
-#define nEP4_TX_ENA 0x0
-#define EP5_TX_ENA 0x20 /* Transmit endpoint 5 enable */
-#define nEP5_TX_ENA 0x0
-#define EP6_TX_ENA 0x40 /* Transmit endpoint 6 enable */
-#define nEP6_TX_ENA 0x0
-#define EP7_TX_ENA 0x80 /* Transmit endpoint 7 enable */
-#define nEP7_TX_ENA 0x0
-#define EP1_RX_ENA 0x100 /* Receive endpoint 1 enable */
-#define nEP1_RX_ENA 0x0
-#define EP2_RX_ENA 0x200 /* Receive endpoint 2 enable */
-#define nEP2_RX_ENA 0x0
-#define EP3_RX_ENA 0x400 /* Receive endpoint 3 enable */
-#define nEP3_RX_ENA 0x0
-#define EP4_RX_ENA 0x800 /* Receive endpoint 4 enable */
-#define nEP4_RX_ENA 0x0
-#define EP5_RX_ENA 0x1000 /* Receive endpoint 5 enable */
-#define nEP5_RX_ENA 0x0
-#define EP6_RX_ENA 0x2000 /* Receive endpoint 6 enable */
-#define nEP6_RX_ENA 0x0
-#define EP7_RX_ENA 0x4000 /* Receive endpoint 7 enable */
-#define nEP7_RX_ENA 0x0
-
-/* Bit masks for USB_OTG_DEV_CTL */
-
-#define SESSION 0x1 /* session indicator */
-#define nSESSION 0x0
-#define HOST_REQ 0x2 /* Host negotiation request */
-#define nHOST_REQ 0x0
-#define HOST_MODE 0x4 /* indicates USBDRC is a host */
-#define nHOST_MODE 0x0
-#define VBUS0 0x8 /* Vbus level indicator[0] */
-#define nVBUS0 0x0
-#define VBUS1 0x10 /* Vbus level indicator[1] */
-#define nVBUS1 0x0
-#define LSDEV 0x20 /* Low-speed indicator */
-#define nLSDEV 0x0
-#define FSDEV 0x40 /* Full or High-speed indicator */
-#define nFSDEV 0x0
-#define B_DEVICE 0x80 /* A' or 'B' device indicator */
-#define nB_DEVICE 0x0
-
-/* Bit masks for USB_OTG_VBUS_IRQ */
-
-#define DRIVE_VBUS_ON 0x1 /* indicator to drive VBUS control circuit */
-#define nDRIVE_VBUS_ON 0x0
-#define DRIVE_VBUS_OFF 0x2 /* indicator to shut off charge pump */
-#define nDRIVE_VBUS_OFF 0x0
-#define CHRG_VBUS_START 0x4 /* indicator for external circuit to start charging VBUS */
-#define nCHRG_VBUS_START 0x0
-#define CHRG_VBUS_END 0x8 /* indicator for external circuit to end charging VBUS */
-#define nCHRG_VBUS_END 0x0
-#define DISCHRG_VBUS_START 0x10 /* indicator to start discharging VBUS */
-#define nDISCHRG_VBUS_START 0x0
-#define DISCHRG_VBUS_END 0x20 /* indicator to stop discharging VBUS */
-#define nDISCHRG_VBUS_END 0x0
-
-/* Bit masks for USB_OTG_VBUS_MASK */
-
-#define DRIVE_VBUS_ON_ENA 0x1 /* enable DRIVE_VBUS_ON interrupt */
-#define nDRIVE_VBUS_ON_ENA 0x0
-#define DRIVE_VBUS_OFF_ENA 0x2 /* enable DRIVE_VBUS_OFF interrupt */
-#define nDRIVE_VBUS_OFF_ENA 0x0
-#define CHRG_VBUS_START_ENA 0x4 /* enable CHRG_VBUS_START interrupt */
-#define nCHRG_VBUS_START_ENA 0x0
-#define CHRG_VBUS_END_ENA 0x8 /* enable CHRG_VBUS_END interrupt */
-#define nCHRG_VBUS_END_ENA 0x0
-#define DISCHRG_VBUS_START_ENA 0x10 /* enable DISCHRG_VBUS_START interrupt */
-#define nDISCHRG_VBUS_START_ENA 0x0
-#define DISCHRG_VBUS_END_ENA 0x20 /* enable DISCHRG_VBUS_END interrupt */
-#define nDISCHRG_VBUS_END_ENA 0x0
-
-/* Bit masks for USB_CSR0 */
-
-#define RXPKTRDY 0x1 /* data packet receive indicator */
-#define nRXPKTRDY 0x0
-#define TXPKTRDY 0x2 /* data packet in FIFO indicator */
-#define nTXPKTRDY 0x0
-#define STALL_SENT 0x4 /* STALL handshake sent */
-#define nSTALL_SENT 0x0
-#define DATAEND 0x8 /* Data end indicator */
-#define nDATAEND 0x0
-#define SETUPEND 0x10 /* Setup end */
-#define nSETUPEND 0x0
-#define SENDSTALL 0x20 /* Send STALL handshake */
-#define nSENDSTALL 0x0
-#define SERVICED_RXPKTRDY 0x40 /* used to clear the RxPktRdy bit */
-#define nSERVICED_RXPKTRDY 0x0
-#define SERVICED_SETUPEND 0x80 /* used to clear the SetupEnd bit */
-#define nSERVICED_SETUPEND 0x0
-#define FLUSHFIFO 0x100 /* flush endpoint FIFO */
-#define nFLUSHFIFO 0x0
-#define STALL_RECEIVED_H 0x4 /* STALL handshake received host mode */
-#define nSTALL_RECEIVED_H 0x0
-#define SETUPPKT_H 0x8 /* send Setup token host mode */
-#define nSETUPPKT_H 0x0
-#define ERROR_H 0x10 /* timeout error indicator host mode */
-#define nERROR_H 0x0
-#define REQPKT_H 0x20 /* Request an IN transaction host mode */
-#define nREQPKT_H 0x0
-#define STATUSPKT_H 0x40 /* Status stage transaction host mode */
-#define nSTATUSPKT_H 0x0
-#define NAK_TIMEOUT_H 0x80 /* EP0 halted after a NAK host mode */
-#define nNAK_TIMEOUT_H 0x0
-
-/* Bit masks for USB_COUNT0 */
-
-#define EP0_RX_COUNT 0x7f /* number of received bytes in EP0 FIFO */
-
-/* Bit masks for USB_NAKLIMIT0 */
-
-#define EP0_NAK_LIMIT 0x1f /* number of frames/micro frames after which EP0 timeouts */
-
-/* Bit masks for USB_TX_MAX_PACKET */
-
-#define MAX_PACKET_SIZE_T 0x7ff /* maximum data pay load in a frame */
-
-/* Bit masks for USB_RX_MAX_PACKET */
-
-#define MAX_PACKET_SIZE_R 0x7ff /* maximum data pay load in a frame */
-
-/* Bit masks for USB_TXCSR */
-
-#define TXPKTRDY_T 0x1 /* data packet in FIFO indicator */
-#define nTXPKTRDY_T 0x0
-#define FIFO_NOT_EMPTY_T 0x2 /* FIFO not empty */
-#define nFIFO_NOT_EMPTY_T 0x0
-#define UNDERRUN_T 0x4 /* TxPktRdy not set for an IN token */
-#define nUNDERRUN_T 0x0
-#define FLUSHFIFO_T 0x8 /* flush endpoint FIFO */
-#define nFLUSHFIFO_T 0x0
-#define STALL_SEND_T 0x10 /* issue a Stall handshake */
-#define nSTALL_SEND_T 0x0
-#define STALL_SENT_T 0x20 /* Stall handshake transmitted */
-#define nSTALL_SENT_T 0x0
-#define CLEAR_DATATOGGLE_T 0x40 /* clear endpoint data toggle */
-#define nCLEAR_DATATOGGLE_T 0x0
-#define INCOMPTX_T 0x80 /* indicates that a large packet is split */
-#define nINCOMPTX_T 0x0
-#define DMAREQMODE_T 0x400 /* DMA mode (0 or 1) selection */
-#define nDMAREQMODE_T 0x0
-#define FORCE_DATATOGGLE_T 0x800 /* Force data toggle */
-#define nFORCE_DATATOGGLE_T 0x0
-#define DMAREQ_ENA_T 0x1000 /* Enable DMA request for Tx EP */
-#define nDMAREQ_ENA_T 0x0
-#define ISO_T 0x4000 /* enable Isochronous transfers */
-#define nISO_T 0x0
-#define AUTOSET_T 0x8000 /* allows TxPktRdy to be set automatically */
-#define nAUTOSET_T 0x0
-#define ERROR_TH 0x4 /* error condition host mode */
-#define nERROR_TH 0x0
-#define STALL_RECEIVED_TH 0x20 /* Stall handshake received host mode */
-#define nSTALL_RECEIVED_TH 0x0
-#define NAK_TIMEOUT_TH 0x80 /* NAK timeout host mode */
-#define nNAK_TIMEOUT_TH 0x0
-
-/* Bit masks for USB_TXCOUNT */
-
-#define TX_COUNT 0x1fff /* Number of bytes to be written to the selected endpoint Tx FIFO */
-
-/* Bit masks for USB_RXCSR */
-
-#define RXPKTRDY_R 0x1 /* data packet in FIFO indicator */
-#define nRXPKTRDY_R 0x0
-#define FIFO_FULL_R 0x2 /* FIFO not empty */
-#define nFIFO_FULL_R 0x0
-#define OVERRUN_R 0x4 /* TxPktRdy not set for an IN token */
-#define nOVERRUN_R 0x0
-#define DATAERROR_R 0x8 /* Out packet cannot be loaded into Rx FIFO */
-#define nDATAERROR_R 0x0
-#define FLUSHFIFO_R 0x10 /* flush endpoint FIFO */
-#define nFLUSHFIFO_R 0x0
-#define STALL_SEND_R 0x20 /* issue a Stall handshake */
-#define nSTALL_SEND_R 0x0
-#define STALL_SENT_R 0x40 /* Stall handshake transmitted */
-#define nSTALL_SENT_R 0x0
-#define CLEAR_DATATOGGLE_R 0x80 /* clear endpoint data toggle */
-#define nCLEAR_DATATOGGLE_R 0x0
-#define INCOMPRX_R 0x100 /* indicates that a large packet is split */
-#define nINCOMPRX_R 0x0
-#define DMAREQMODE_R 0x800 /* DMA mode (0 or 1) selection */
-#define nDMAREQMODE_R 0x0
-#define DISNYET_R 0x1000 /* disable Nyet handshakes */
-#define nDISNYET_R 0x0
-#define DMAREQ_ENA_R 0x2000 /* Enable DMA request for Tx EP */
-#define nDMAREQ_ENA_R 0x0
-#define ISO_R 0x4000 /* enable Isochronous transfers */
-#define nISO_R 0x0
-#define AUTOCLEAR_R 0x8000 /* allows TxPktRdy to be set automatically */
-#define nAUTOCLEAR_R 0x0
-#define ERROR_RH 0x4 /* TxPktRdy not set for an IN token host mode */
-#define nERROR_RH 0x0
-#define REQPKT_RH 0x20 /* request an IN transaction host mode */
-#define nREQPKT_RH 0x0
-#define STALL_RECEIVED_RH 0x40 /* Stall handshake received host mode */
-#define nSTALL_RECEIVED_RH 0x0
-#define INCOMPRX_RH 0x100 /* indicates that a large packet is split host mode */
-#define nINCOMPRX_RH 0x0
-#define DMAREQMODE_RH 0x800 /* DMA mode (0 or 1) selection host mode */
-#define nDMAREQMODE_RH 0x0
-#define AUTOREQ_RH 0x4000 /* sets ReqPkt automatically host mode */
-#define nAUTOREQ_RH 0x0
-
-/* Bit masks for USB_RXCOUNT */
-
-#define RX_COUNT 0x1fff /* Number of received bytes in the packet in the Rx FIFO */
-
-/* Bit masks for USB_TXTYPE */
-
-#define TARGET_EP_NO_T 0xf /* EP number */
-#define PROTOCOL_T 0xc /* transfer type */
-
-/* Bit masks for USB_TXINTERVAL */
-
-#define TX_POLL_INTERVAL 0xff /* polling interval for selected Tx EP */
-
-/* Bit masks for USB_RXTYPE */
-
-#define TARGET_EP_NO_R 0xf /* EP number */
-#define PROTOCOL_R 0xc /* transfer type */
-
-/* Bit masks for USB_RXINTERVAL */
-
-#define RX_POLL_INTERVAL 0xff /* polling interval for selected Rx EP */
-
-/* Bit masks for USB_DMA_INTERRUPT */
-
-#define DMA0_INT 0x1 /* DMA0 pending interrupt */
-#define nDMA0_INT 0x0
-#define DMA1_INT 0x2 /* DMA1 pending interrupt */
-#define nDMA1_INT 0x0
-#define DMA2_INT 0x4 /* DMA2 pending interrupt */
-#define nDMA2_INT 0x0
-#define DMA3_INT 0x8 /* DMA3 pending interrupt */
-#define nDMA3_INT 0x0
-#define DMA4_INT 0x10 /* DMA4 pending interrupt */
-#define nDMA4_INT 0x0
-#define DMA5_INT 0x20 /* DMA5 pending interrupt */
-#define nDMA5_INT 0x0
-#define DMA6_INT 0x40 /* DMA6 pending interrupt */
-#define nDMA6_INT 0x0
-#define DMA7_INT 0x80 /* DMA7 pending interrupt */
-#define nDMA7_INT 0x0
-
-/* Bit masks for USB_DMAxCONTROL */
-
-#define DMA_ENA 0x1 /* DMA enable */
-#define nDMA_ENA 0x0
-#define DIRECTION 0x2 /* direction of DMA transfer */
-#define nDIRECTION 0x0
-#define MODE 0x4 /* DMA Bus error */
-#define nMODE 0x0
-#define INT_ENA 0x8 /* Interrupt enable */
-#define nINT_ENA 0x0
-#define EPNUM 0xf0 /* EP number */
-#define BUSERROR 0x100 /* DMA Bus error */
-#define nBUSERROR 0x0
-
-/* Bit masks for USB_DMAxADDRHIGH */
-
-#define DMA_ADDR_HIGH 0xffff /* Upper 16-bits of memory source/destination address for the DMA master channel */
-
-/* Bit masks for USB_DMAxADDRLOW */
-
-#define DMA_ADDR_LOW 0xffff /* Lower 16-bits of memory source/destination address for the DMA master channel */
-
-/* Bit masks for USB_DMAxCOUNTHIGH */
-
-#define DMA_COUNT_HIGH 0xffff /* Upper 16-bits of byte count of DMA transfer for DMA master channel */
-
-/* Bit masks for USB_DMAxCOUNTLOW */
-
-#define DMA_COUNT_LOW 0xffff /* Lower 16-bits of byte count of DMA transfer for DMA master channel */
-
#endif /* _DEF_BF527_H */
git.openpandora.org / pandora-kernel.git / commitdiff