* 'omap-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap-2.6: (33 commits)
OMAP3: PM: Boot message is not an error, and not helpful, remove it
OMAP3: cpuidle: change the power domains modes determination logic
OMAP3: cpuidle: code rework for improved readability
OMAP3: cpuidle: re-organize the C-states data
OMAP3: clean-up mach specific cpuidle data structures
OMAP3 cpuidle: remove useless SDP specific timings
usb: otg: OMAP4430: Powerdown the internal PHY when USB is disabled
usb: otg: OMAP4430: Fixing the omap4430_phy_init function
usb: musb: am35x: fix compile error when building am35x
usb: musb: OMAP4430: Power down the PHY during board init
omap: drop board-igep0030.c
omap: igep0020: add support for IGEP3
omap: igep0020: minor refactoring
omap: igep0020: name refactoring for future merge with IGEP3
omap: Remove support for omap2evm
arm: omap2plus: GPIO cleanup
omap: musb: introduce default board config
omap: move detection of NAND CS to common-board-devices
omap: use common initialization for PMIC i2c bus
omap: consolidate touch screen initialization among different boards
...
CONFIG_MODULE_SRCVERSION_ALL=y
# CONFIG_BLK_DEV_BSG is not set
CONFIG_ARCH_OMAP=y
-CONFIG_ARCH_OMAP2=y
-CONFIG_ARCH_OMAP3=y
-CONFIG_ARCH_OMAP4=y
CONFIG_OMAP_RESET_CLOCKS=y
CONFIG_OMAP_MUX_DEBUG=y
-CONFIG_OMAP_32K_TIMER=y
-CONFIG_MACH_OMAP_GENERIC=y
-CONFIG_ARCH_OMAP2420=y
-CONFIG_ARCH_OMAP2430=y
-CONFIG_ARCH_OMAP3430=y
-CONFIG_MACH_OMAP_H4=y
-CONFIG_MACH_OMAP_APOLLON=y
-CONFIG_MACH_OMAP_2430SDP=y
-CONFIG_MACH_OMAP3_BEAGLE=y
-CONFIG_MACH_DEVKIT8000=y
-CONFIG_MACH_OMAP_LDP=y
-CONFIG_MACH_OVERO=y
-CONFIG_MACH_OMAP3EVM=y
-CONFIG_MACH_OMAP3517EVM=y
-CONFIG_MACH_OMAP3_PANDORA=y
-CONFIG_MACH_OMAP3_TOUCHBOOK=y
-CONFIG_MACH_OMAP_3430SDP=y
-CONFIG_MACH_NOKIA_N8X0=y
-CONFIG_MACH_NOKIA_RX51=y
-CONFIG_MACH_OMAP_ZOOM2=y
-CONFIG_MACH_OMAP_ZOOM3=y
-CONFIG_MACH_CM_T35=y
-CONFIG_MACH_IGEP0020=y
-CONFIG_MACH_SBC3530=y
-CONFIG_MACH_OMAP_3630SDP=y
-CONFIG_MACH_OMAP_4430SDP=y
CONFIG_ARM_THUMBEE=y
-CONFIG_ARM_L1_CACHE_SHIFT=5
CONFIG_ARM_ERRATA_411920=y
CONFIG_NO_HZ=y
CONFIG_HIGH_RES_TIMERS=y
CONFIG_SMP=y
CONFIG_NR_CPUS=2
-# CONFIG_LOCAL_TIMERS is not set
-CONFIG_AEABI=y
CONFIG_LEDS=y
CONFIG_ZBOOT_ROM_TEXT=0x0
CONFIG_ZBOOT_ROM_BSS=0x0
CONFIG_CMDLINE="root=/dev/mmcblk0p2 rootwait console=ttyO2,115200"
CONFIG_KEXEC=y
CONFIG_FPE_NWFPE=y
-CONFIG_VFP=y
-CONFIG_NEON=y
CONFIG_BINFMT_MISC=y
-CONFIG_PM=y
CONFIG_PM_DEBUG=y
-CONFIG_PM_RUNTIME=y
CONFIG_NET=y
CONFIG_PACKET=y
CONFIG_UNIX=y
# CONFIG_IPV6 is not set
CONFIG_NETFILTER=y
CONFIG_BT=m
-CONFIG_BT_L2CAP=m
-CONFIG_BT_SCO=m
-CONFIG_BT_RFCOMM=y
-CONFIG_BT_RFCOMM_TTY=y
-CONFIG_BT_BNEP=m
-CONFIG_BT_BNEP_MC_FILTER=y
-CONFIG_BT_BNEP_PROTO_FILTER=y
-CONFIG_BT_HIDP=m
CONFIG_BT_HCIUART=m
CONFIG_BT_HCIUART_H4=y
CONFIG_BT_HCIUART_BCSP=y
CONFIG_MAC80211=m
CONFIG_MAC80211_RC_PID=y
CONFIG_MAC80211_RC_DEFAULT_PID=y
-CONFIG_MAC80211_LEDS=y
CONFIG_UEVENT_HELPER_PATH="/sbin/hotplug"
CONFIG_CONNECTOR=y
CONFIG_MTD=y
-CONFIG_MTD_CONCAT=y
CONFIG_MTD_CMDLINE_PARTS=y
CONFIG_MTD_CHAR=y
CONFIG_MTD_BLOCK=y
CONFIG_BLK_DEV_LOOP=y
CONFIG_BLK_DEV_RAM=y
CONFIG_BLK_DEV_RAM_SIZE=16384
-CONFIG_EEPROM_LEGACY=y
CONFIG_SCSI=y
CONFIG_BLK_DEV_SD=y
CONFIG_SCSI_MULTI_LUN=y
CONFIG_INPUT_MISC=y
CONFIG_INPUT_TWL4030_PWRBUTTON=y
CONFIG_VT_HW_CONSOLE_BINDING=y
-CONFIG_SERIAL_8250=y
-CONFIG_SERIAL_8250_CONSOLE=y
+# CONFIG_LEGACY_PTYS is not set
CONFIG_SERIAL_8250_NR_UARTS=32
CONFIG_SERIAL_8250_EXTENDED=y
CONFIG_SERIAL_8250_MANY_PORTS=y
CONFIG_SERIAL_8250_SHARE_IRQ=y
CONFIG_SERIAL_8250_DETECT_IRQ=y
CONFIG_SERIAL_8250_RSA=y
-# CONFIG_LEGACY_PTYS is not set
CONFIG_HW_RANDOM=y
-CONFIG_I2C=y
CONFIG_I2C_CHARDEV=y
-CONFIG_I2C_OMAP=y
CONFIG_SPI=y
CONFIG_SPI_OMAP24XX=y
CONFIG_DEBUG_GPIO=y
CONFIG_WATCHDOG=y
CONFIG_OMAP_WATCHDOG=y
CONFIG_TWL4030_WATCHDOG=y
-CONFIG_MENELAUS=y
-CONFIG_TWL4030_CORE=y
-CONFIG_TWL4030_POWER=y
-CONFIG_REGULATOR=y
CONFIG_REGULATOR_TWL4030=y
CONFIG_REGULATOR_TPS65023=y
CONFIG_REGULATOR_TPS6507X=y
CONFIG_LCD_CLASS_DEVICE=y
CONFIG_LCD_PLATFORM=y
CONFIG_DISPLAY_SUPPORT=y
-# CONFIG_VGA_CONSOLE is not set
CONFIG_FRAMEBUFFER_CONSOLE=y
CONFIG_FRAMEBUFFER_CONSOLE_ROTATION=y
CONFIG_FONTS=y
CONFIG_LOGO=y
CONFIG_SOUND=m
CONFIG_SND=m
-CONFIG_SND_MIXER_OSS=y
-CONFIG_SND_PCM_OSS=y
+CONFIG_SND_MIXER_OSS=m
+CONFIG_SND_PCM_OSS=m
CONFIG_SND_VERBOSE_PRINTK=y
CONFIG_SND_DEBUG=y
-CONFIG_SND_USB_AUDIO=y
-CONFIG_SND_SOC=y
-CONFIG_SND_OMAP_SOC=y
-CONFIG_SND_OMAP_SOC_OMAP3_PANDORA=y
+CONFIG_SND_USB_AUDIO=m
+CONFIG_SND_SOC=m
+CONFIG_SND_OMAP_SOC=m
+CONFIG_SND_OMAP_SOC_OMAP3_PANDORA=m
CONFIG_USB=y
CONFIG_USB_DEBUG=y
CONFIG_USB_ANNOUNCE_NEW_DEVICES=y
CONFIG_USB_DEVICEFS=y
CONFIG_USB_SUSPEND=y
-# CONFIG_USB_OTG_WHITELIST is not set
CONFIG_USB_MON=y
-# CONFIG_USB_MUSB_HDRC is not set
-# CONFIG_USB_MUSB_OTG is not set
-# CONFIG_USB_GADGET_MUSB_HDRC is not set
-CONFIG_USB_MUSB_DEBUG=y
CONFIG_USB_WDM=y
CONFIG_USB_STORAGE=y
CONFIG_USB_LIBUSUAL=y
CONFIG_SDIO_UART=y
CONFIG_MMC_OMAP=y
CONFIG_MMC_OMAP_HS=y
-CONFIG_LEDS_CLASS=y
-CONFIG_LEDS_GPIO=y
-CONFIG_LEDS_TRIGGER_TIMER=y
-CONFIG_LEDS_TRIGGER_HEARTBEAT=y
-CONFIG_LEDS_TRIGGER_DEFAULT_ON=y
CONFIG_RTC_CLASS=y
CONFIG_RTC_DRV_TWL92330=y
CONFIG_RTC_DRV_TWL4030=y
CONFIG_EXT2_FS=y
CONFIG_EXT3_FS=y
# CONFIG_EXT3_FS_XATTR is not set
-CONFIG_INOTIFY=y
CONFIG_QUOTA=y
CONFIG_QFMT_V2=y
CONFIG_MSDOS_FS=y
CONFIG_NLS_ISO8859_1=y
CONFIG_PRINTK_TIME=y
CONFIG_MAGIC_SYSRQ=y
-CONFIG_DEBUG_FS=y
CONFIG_DEBUG_KERNEL=y
CONFIG_SCHEDSTATS=y
CONFIG_TIMER_STATS=y
CONFIG_PROVE_LOCKING=y
-# CONFIG_LOCK_STAT is not set
CONFIG_DEBUG_SPINLOCK_SLEEP=y
# CONFIG_DEBUG_BUGVERBOSE is not set
CONFIG_DEBUG_INFO=y
depends on ARCH_OMAP3
default y
select OMAP_PACKAGE_CBB
+ select MACH_IGEP0020
config MACH_SBC3530
bool "OMAP3 SBC STALKER board"
obj-$(CONFIG_MACH_CM_T3517) += board-cm-t3517.o
obj-$(CONFIG_MACH_IGEP0020) += board-igep0020.o \
hsmmc.o
-obj-$(CONFIG_MACH_IGEP0030) += board-igep0030.o \
- hsmmc.o
obj-$(CONFIG_MACH_OMAP3_TOUCHBOOK) += board-omap3touchbook.o \
hsmmc.o
obj-$(CONFIG_MACH_OMAP_4430SDP) += board-4430sdp.o \
disp-$(CONFIG_OMAP2_DSS) := display.o
obj-y += $(disp-m) $(disp-y)
+
+obj-y += common-board-devices.o
#include "mux.h"
#include "hsmmc.h"
+#include "common-board-devices.h"
#define SDP2430_CS0_BASE 0x04000000
#define SECONDARY_LCD_GPIO 147
.vmmc1 = &sdp2430_vmmc1,
};
-static struct i2c_board_info __initdata sdp2430_i2c_boardinfo[] = {
- {
- I2C_BOARD_INFO("twl4030", 0x48),
- .flags = I2C_CLIENT_WAKE,
- .irq = INT_24XX_SYS_NIRQ,
- .platform_data = &sdp2430_twldata,
- },
-};
-
static struct i2c_board_info __initdata sdp2430_i2c1_boardinfo[] = {
{
I2C_BOARD_INFO("isp1301_omap", 0x2D),
{
omap_register_i2c_bus(1, 100, sdp2430_i2c1_boardinfo,
ARRAY_SIZE(sdp2430_i2c1_boardinfo));
- omap_register_i2c_bus(2, 2600, sdp2430_i2c_boardinfo,
- ARRAY_SIZE(sdp2430_i2c_boardinfo));
+ omap2_pmic_init("twl4030", &sdp2430_twldata);
return 0;
}
{} /* Terminator */
};
-static struct omap_musb_board_data musb_board_data = {
- .interface_type = MUSB_INTERFACE_ULPI,
- .mode = MUSB_OTG,
- .power = 100,
-};
static struct omap_usb_config sdp2430_usb_config __initdata = {
.otg = 1,
#ifdef CONFIG_USB_GADGET_OMAP
static void __init omap_2430sdp_init(void)
{
- int ret;
-
omap2430_mux_init(board_mux, OMAP_PACKAGE_ZAC);
omap_board_config = sdp2430_config;
omap2_usbfs_init(&sdp2430_usb_config);
omap_mux_init_signal("usb0hs_stp", OMAP_PULL_ENA | OMAP_PULL_UP);
- usb_musb_init(&musb_board_data);
+ usb_musb_init(NULL);
board_smc91x_init();
/* Turn off secondary LCD backlight */
- ret = gpio_request(SECONDARY_LCD_GPIO, "Secondary LCD backlight");
- if (ret == 0)
- gpio_direction_output(SECONDARY_LCD_GPIO, 0);
+ gpio_request_one(SECONDARY_LCD_GPIO, GPIOF_OUT_INIT_LOW,
+ "Secondary LCD backlight");
}
static void __init omap_2430sdp_map_io(void)
#include <linux/input.h>
#include <linux/input/matrix_keypad.h>
#include <linux/spi/spi.h>
-#include <linux/spi/ads7846.h>
#include <linux/i2c/twl.h>
#include <linux/regulator/machine.h>
#include <linux/io.h>
#include "hsmmc.h"
#include "pm.h"
#include "control.h"
+#include "common-board-devices.h"
#define CONFIG_DISABLE_HFCLK 1
#define TWL4030_MSECURE_GPIO 22
-/* FIXME: These values need to be updated based on more profiling on 3430sdp*/
-static struct cpuidle_params omap3_cpuidle_params_table[] = {
- /* C1 */
- {1, 2, 2, 5},
- /* C2 */
- {1, 10, 10, 30},
- /* C3 */
- {1, 50, 50, 300},
- /* C4 */
- {1, 1500, 1800, 4000},
- /* C5 */
- {1, 2500, 7500, 12000},
- /* C6 */
- {1, 3000, 8500, 15000},
- /* C7 */
- {1, 10000, 30000, 300000},
-};
-
static uint32_t board_keymap[] = {
KEY(0, 0, KEY_LEFT),
KEY(0, 1, KEY_RIGHT),
.rep = 1,
};
-static int ts_gpio; /* Needed for ads7846_get_pendown_state */
-
-/**
- * @brief ads7846_dev_init : Requests & sets GPIO line for pen-irq
- *
- * @return - void. If request gpio fails then Flag KERN_ERR.
- */
-static void ads7846_dev_init(void)
-{
- if (gpio_request(ts_gpio, "ADS7846 pendown") < 0) {
- printk(KERN_ERR "can't get ads746 pen down GPIO\n");
- return;
- }
-
- gpio_direction_input(ts_gpio);
- gpio_set_debounce(ts_gpio, 310);
-}
-
-static int ads7846_get_pendown_state(void)
-{
- return !gpio_get_value(ts_gpio);
-}
-
-static struct ads7846_platform_data tsc2046_config __initdata = {
- .get_pendown_state = ads7846_get_pendown_state,
- .keep_vref_on = 1,
- .wakeup = true,
-};
-
-
-static struct omap2_mcspi_device_config tsc2046_mcspi_config = {
- .turbo_mode = 0,
- .single_channel = 1, /* 0: slave, 1: master */
-};
-
-static struct spi_board_info sdp3430_spi_board_info[] __initdata = {
- [0] = {
- /*
- * TSC2046 operates at a max freqency of 2MHz, so
- * operate slightly below at 1.5MHz
- */
- .modalias = "ads7846",
- .bus_num = 1,
- .chip_select = 0,
- .max_speed_hz = 1500000,
- .controller_data = &tsc2046_mcspi_config,
- .irq = 0,
- .platform_data = &tsc2046_config,
- },
-};
-
-
#define SDP3430_LCD_PANEL_BACKLIGHT_GPIO 8
#define SDP3430_LCD_PANEL_ENABLE_GPIO 5
-static unsigned backlight_gpio;
-static unsigned enable_gpio;
+static struct gpio sdp3430_dss_gpios[] __initdata = {
+ {SDP3430_LCD_PANEL_ENABLE_GPIO, GPIOF_OUT_INIT_LOW, "LCD reset" },
+ {SDP3430_LCD_PANEL_BACKLIGHT_GPIO, GPIOF_OUT_INIT_LOW, "LCD Backlight"},
+};
+
static int lcd_enabled;
static int dvi_enabled;
{
int r;
- enable_gpio = SDP3430_LCD_PANEL_ENABLE_GPIO;
- backlight_gpio = SDP3430_LCD_PANEL_BACKLIGHT_GPIO;
-
- r = gpio_request(enable_gpio, "LCD reset");
- if (r) {
- printk(KERN_ERR "failed to get LCD reset GPIO\n");
- goto err0;
- }
-
- r = gpio_request(backlight_gpio, "LCD Backlight");
- if (r) {
- printk(KERN_ERR "failed to get LCD backlight GPIO\n");
- goto err1;
- }
-
- gpio_direction_output(enable_gpio, 0);
- gpio_direction_output(backlight_gpio, 0);
+ r = gpio_request_array(sdp3430_dss_gpios,
+ ARRAY_SIZE(sdp3430_dss_gpios));
+ if (r)
+ printk(KERN_ERR "failed to get LCD control GPIOs\n");
- return;
-err1:
- gpio_free(enable_gpio);
-err0:
- return;
}
static int sdp3430_panel_enable_lcd(struct omap_dss_device *dssdev)
return -EINVAL;
}
- gpio_direction_output(enable_gpio, 1);
- gpio_direction_output(backlight_gpio, 1);
+ gpio_direction_output(SDP3430_LCD_PANEL_ENABLE_GPIO, 1);
+ gpio_direction_output(SDP3430_LCD_PANEL_BACKLIGHT_GPIO, 1);
lcd_enabled = 1;
{
lcd_enabled = 0;
- gpio_direction_output(enable_gpio, 0);
- gpio_direction_output(backlight_gpio, 0);
+ gpio_direction_output(SDP3430_LCD_PANEL_ENABLE_GPIO, 0);
+ gpio_direction_output(SDP3430_LCD_PANEL_BACKLIGHT_GPIO, 0);
}
static int sdp3430_panel_enable_dvi(struct omap_dss_device *dssdev)
omap2_hsmmc_init(mmc);
/* gpio + 7 is "sub_lcd_en_bkl" (output/PWM1) */
- gpio_request(gpio + 7, "sub_lcd_en_bkl");
- gpio_direction_output(gpio + 7, 0);
+ gpio_request_one(gpio + 7, GPIOF_OUT_INIT_LOW, "sub_lcd_en_bkl");
/* gpio + 15 is "sub_lcd_nRST" (output) */
- gpio_request(gpio + 15, "sub_lcd_nRST");
- gpio_direction_output(gpio + 15, 0);
+ gpio_request_one(gpio + 15, GPIOF_OUT_INIT_LOW, "sub_lcd_nRST");
return 0;
}
.vpll2 = &sdp3430_vpll2,
};
-static struct i2c_board_info __initdata sdp3430_i2c_boardinfo[] = {
- {
- I2C_BOARD_INFO("twl4030", 0x48),
- .flags = I2C_CLIENT_WAKE,
- .irq = INT_34XX_SYS_NIRQ,
- .platform_data = &sdp3430_twldata,
- },
-};
-
static int __init omap3430_i2c_init(void)
{
/* i2c1 for PMIC only */
- omap_register_i2c_bus(1, 2600, sdp3430_i2c_boardinfo,
- ARRAY_SIZE(sdp3430_i2c_boardinfo));
+ omap3_pmic_init("twl4030", &sdp3430_twldata);
/* i2c2 on camera connector (for sensor control) and optional isp1301 */
omap_register_i2c_bus(2, 400, NULL, 0);
/* i2c3 on display connector (for DVI, tfp410) */
},
};
-static struct omap_musb_board_data musb_board_data = {
- .interface_type = MUSB_INTERFACE_ULPI,
- .mode = MUSB_OTG,
- .power = 100,
-};
-
static void __init omap_3430sdp_init(void)
{
+ int gpio_pendown;
+
omap3_mux_init(board_mux, OMAP_PACKAGE_CBB);
omap_board_config = sdp3430_config;
omap_board_config_size = ARRAY_SIZE(sdp3430_config);
- omap3_pm_init_cpuidle(omap3_cpuidle_params_table);
omap3430_i2c_init();
omap_display_init(&sdp3430_dss_data);
if (omap_rev() > OMAP3430_REV_ES1_0)
- ts_gpio = SDP3430_TS_GPIO_IRQ_SDPV2;
+ gpio_pendown = SDP3430_TS_GPIO_IRQ_SDPV2;
else
- ts_gpio = SDP3430_TS_GPIO_IRQ_SDPV1;
- sdp3430_spi_board_info[0].irq = gpio_to_irq(ts_gpio);
- spi_register_board_info(sdp3430_spi_board_info,
- ARRAY_SIZE(sdp3430_spi_board_info));
- ads7846_dev_init();
+ gpio_pendown = SDP3430_TS_GPIO_IRQ_SDPV1;
+ omap_ads7846_init(1, gpio_pendown, 310, NULL);
board_serial_init();
- usb_musb_init(&musb_board_data);
+ usb_musb_init(NULL);
board_smc91x_init();
board_flash_init(sdp_flash_partitions, chip_sel_3430, 0);
sdp3430_display_init();
#include "hsmmc.h"
#include "timer-gp.h"
#include "control.h"
+#include "common-board-devices.h"
#define ETH_KS8851_IRQ 34
#define ETH_KS8851_POWER_ON 48
},
};
+static struct gpio sdp4430_eth_gpios[] __initdata = {
+ { ETH_KS8851_POWER_ON, GPIOF_OUT_INIT_HIGH, "eth_power" },
+ { ETH_KS8851_QUART, GPIOF_OUT_INIT_HIGH, "quart" },
+ { ETH_KS8851_IRQ, GPIOF_IN, "eth_irq" },
+};
+
static int omap_ethernet_init(void)
{
int status;
/* Request of GPIO lines */
+ status = gpio_request_array(sdp4430_eth_gpios,
+ ARRAY_SIZE(sdp4430_eth_gpios));
+ if (status)
+ pr_err("Cannot request ETH GPIOs\n");
- status = gpio_request(ETH_KS8851_POWER_ON, "eth_power");
- if (status) {
- pr_err("Cannot request GPIO %d\n", ETH_KS8851_POWER_ON);
- return status;
- }
-
- status = gpio_request(ETH_KS8851_QUART, "quart");
- if (status) {
- pr_err("Cannot request GPIO %d\n", ETH_KS8851_QUART);
- goto error1;
- }
-
- status = gpio_request(ETH_KS8851_IRQ, "eth_irq");
- if (status) {
- pr_err("Cannot request GPIO %d\n", ETH_KS8851_IRQ);
- goto error2;
- }
-
- /* Configuration of requested GPIO lines */
-
- status = gpio_direction_output(ETH_KS8851_POWER_ON, 1);
- if (status) {
- pr_err("Cannot set output GPIO %d\n", ETH_KS8851_IRQ);
- goto error3;
- }
-
- status = gpio_direction_output(ETH_KS8851_QUART, 1);
- if (status) {
- pr_err("Cannot set output GPIO %d\n", ETH_KS8851_QUART);
- goto error3;
- }
-
- status = gpio_direction_input(ETH_KS8851_IRQ);
- if (status) {
- pr_err("Cannot set input GPIO %d\n", ETH_KS8851_IRQ);
- goto error3;
- }
-
- return 0;
-
-error3:
- gpio_free(ETH_KS8851_IRQ);
-error2:
- gpio_free(ETH_KS8851_QUART);
-error1:
- gpio_free(ETH_KS8851_POWER_ON);
return status;
}
.usb = &omap4_usbphy_data
};
-static struct i2c_board_info __initdata sdp4430_i2c_boardinfo[] = {
- {
- I2C_BOARD_INFO("twl6030", 0x48),
- .flags = I2C_CLIENT_WAKE,
- .irq = OMAP44XX_IRQ_SYS_1N,
- .platform_data = &sdp4430_twldata,
- },
-};
static struct i2c_board_info __initdata sdp4430_i2c_3_boardinfo[] = {
{
I2C_BOARD_INFO("tmp105", 0x48),
};
static int __init omap4_i2c_init(void)
{
- /*
- * Phoenix Audio IC needs I2C1 to
- * start with 400 KHz or less
- */
- omap_register_i2c_bus(1, 400, sdp4430_i2c_boardinfo,
- ARRAY_SIZE(sdp4430_i2c_boardinfo));
+ omap4_pmic_init("twl6030", &sdp4430_twldata);
omap_register_i2c_bus(2, 400, NULL, 0);
omap_register_i2c_bus(3, 400, sdp4430_i2c_3_boardinfo,
ARRAY_SIZE(sdp4430_i2c_3_boardinfo));
static void __init omap_sfh7741prox_init(void)
{
- int error;
+ int error;
- error = gpio_request(OMAP4_SFH7741_ENABLE_GPIO, "sfh7741");
- if (error < 0) {
+ error = gpio_request_one(OMAP4_SFH7741_ENABLE_GPIO,
+ GPIOF_OUT_INIT_LOW, "sfh7741");
+ if (error < 0)
pr_err("%s:failed to request GPIO %d, error %d\n",
__func__, OMAP4_SFH7741_ENABLE_GPIO, error);
- return;
- }
-
- error = gpio_direction_output(OMAP4_SFH7741_ENABLE_GPIO , 0);
- if (error < 0) {
- pr_err("%s: GPIO configuration failed: GPIO %d,error %d\n",
- __func__, OMAP4_SFH7741_ENABLE_GPIO, error);
- gpio_free(OMAP4_SFH7741_ENABLE_GPIO);
- }
}
static void sdp4430_hdmi_mux_init(void)
OMAP_PIN_INPUT_PULLUP);
}
+static struct gpio sdp4430_hdmi_gpios[] = {
+ { HDMI_GPIO_HPD, GPIOF_OUT_INIT_HIGH, "hdmi_gpio_hpd" },
+ { HDMI_GPIO_LS_OE, GPIOF_OUT_INIT_HIGH, "hdmi_gpio_ls_oe" },
+};
+
static int sdp4430_panel_enable_hdmi(struct omap_dss_device *dssdev)
{
int status;
- status = gpio_request_one(HDMI_GPIO_HPD, GPIOF_OUT_INIT_HIGH,
- "hdmi_gpio_hpd");
- if (status) {
- pr_err("Cannot request GPIO %d\n", HDMI_GPIO_HPD);
- return status;
- }
- status = gpio_request_one(HDMI_GPIO_LS_OE, GPIOF_OUT_INIT_HIGH,
- "hdmi_gpio_ls_oe");
- if (status) {
- pr_err("Cannot request GPIO %d\n", HDMI_GPIO_LS_OE);
- goto error1;
- }
-
- return 0;
-
-error1:
- gpio_free(HDMI_GPIO_HPD);
+ status = gpio_request_array(sdp4430_hdmi_gpios,
+ ARRAY_SIZE(sdp4430_hdmi_gpios));
+ if (status)
+ pr_err("%s: Cannot request HDMI GPIOs\n", __func__);
return status;
}
return;
}
- ret = gpio_request(GPIO_USB_POWER, "usb_ehci_enable");
+ ret = gpio_request_one(GPIO_USB_POWER, GPIOF_OUT_INIT_HIGH,
+ "usb_ehci_enable");
if (ret < 0) {
pr_err("Can not request GPIO %d\n", GPIO_USB_POWER);
return;
}
- ret = gpio_direction_output(GPIO_USB_POWER, 1);
- if (ret < 0) {
- gpio_free(GPIO_USB_POWER);
- pr_err("Unable to initialize EHCI power\n");
- return;
- }
-
usbhs_init(&usbhs_bdata);
}
int r;
omap_mux_init_gpio(GPIO_RTCS35390A_IRQ, OMAP_PIN_INPUT_PULLUP);
- r = gpio_request(GPIO_RTCS35390A_IRQ, "rtcs35390a-irq");
+
+ r = gpio_request_one(GPIO_RTCS35390A_IRQ, GPIOF_IN, "rtcs35390a-irq");
if (r < 0) {
printk(KERN_WARNING "failed to request GPIO#%d\n",
GPIO_RTCS35390A_IRQ);
return;
}
- r = gpio_direction_input(GPIO_RTCS35390A_IRQ);
- if (r < 0) {
- printk(KERN_WARNING "GPIO#%d cannot be configured as input\n",
- GPIO_RTCS35390A_IRQ);
- gpio_free(GPIO_RTCS35390A_IRQ);
- return;
- }
+
am3517evm_i2c1_boardinfo[0].irq = gpio_to_irq(GPIO_RTCS35390A_IRQ);
}
#if defined(CONFIG_PANEL_SHARP_LQ043T1DG01) || \
defined(CONFIG_PANEL_SHARP_LQ043T1DG01_MODULE)
+static struct gpio am3517_evm_dss_gpios[] __initdata = {
+ /* GPIO 182 = LCD Backlight Power */
+ { LCD_PANEL_BKLIGHT_PWR, GPIOF_OUT_INIT_HIGH, "lcd_backlight_pwr" },
+ /* GPIO 181 = LCD Panel PWM */
+ { LCD_PANEL_PWM, GPIOF_OUT_INIT_HIGH, "lcd bl enable" },
+ /* GPIO 176 = LCD Panel Power enable pin */
+ { LCD_PANEL_PWR, GPIOF_OUT_INIT_HIGH, "dvi enable" },
+};
+
static void __init am3517_evm_display_init(void)
{
int r;
omap_mux_init_gpio(LCD_PANEL_PWR, OMAP_PIN_INPUT_PULLUP);
omap_mux_init_gpio(LCD_PANEL_BKLIGHT_PWR, OMAP_PIN_INPUT_PULLDOWN);
omap_mux_init_gpio(LCD_PANEL_PWM, OMAP_PIN_INPUT_PULLDOWN);
- /*
- * Enable GPIO 182 = LCD Backlight Power
- */
- r = gpio_request(LCD_PANEL_BKLIGHT_PWR, "lcd_backlight_pwr");
+
+ r = gpio_request_array(am3517_evm_dss_gpios,
+ ARRAY_SIZE(am3517_evm_dss_gpios));
if (r) {
- printk(KERN_ERR "failed to get lcd_backlight_pwr\n");
+ printk(KERN_ERR "failed to get DSS panel control GPIOs\n");
return;
}
- gpio_direction_output(LCD_PANEL_BKLIGHT_PWR, 1);
- /*
- * Enable GPIO 181 = LCD Panel PWM
- */
- r = gpio_request(LCD_PANEL_PWM, "lcd_pwm");
- if (r) {
- printk(KERN_ERR "failed to get lcd_pwm\n");
- goto err_1;
- }
- gpio_direction_output(LCD_PANEL_PWM, 1);
- /*
- * Enable GPIO 176 = LCD Panel Power enable pin
- */
- r = gpio_request(LCD_PANEL_PWR, "lcd_panel_pwr");
- if (r) {
- printk(KERN_ERR "failed to get lcd_panel_pwr\n");
- goto err_2;
- }
- gpio_direction_output(LCD_PANEL_PWR, 1);
printk(KERN_INFO "Display initialized successfully\n");
- return;
-
-err_2:
- gpio_free(LCD_PANEL_PWM);
-err_1:
- gpio_free(LCD_PANEL_BKLIGHT_PWR);
}
#else
static void __init am3517_evm_display_init(void) {}
.power = 500,
.set_phy_power = am35x_musb_phy_power,
.clear_irq = am35x_musb_clear_irq,
- .set_mode = am35x_musb_set_mode,
+ .set_mode = am35x_set_mode,
.reset = am35x_musb_reset,
};
unsigned int rate;
struct clk *gpmc_fck;
int eth_cs;
+ int err;
gpmc_fck = clk_get(NULL, "gpmc_fck"); /* Always on ENABLE_ON_INIT */
if (IS_ERR(gpmc_fck)) {
apollon_smc91x_resources[0].end = base + 0x30f;
udelay(100);
- omap_mux_init_gpio(74, 0);
- if (gpio_request(APOLLON_ETHR_GPIO_IRQ, "SMC91x irq") < 0) {
+ omap_mux_init_gpio(APOLLON_ETHR_GPIO_IRQ, 0);
+ err = gpio_request_one(APOLLON_ETHR_GPIO_IRQ, GPIOF_IN, "SMC91x irq");
+ if (err) {
printk(KERN_ERR "Failed to request GPIO%d for smc91x IRQ\n",
APOLLON_ETHR_GPIO_IRQ);
gpmc_cs_free(APOLLON_ETH_CS);
- goto out;
}
- gpio_direction_input(APOLLON_ETHR_GPIO_IRQ);
-
out:
clk_disable(gpmc_fck);
clk_put(gpmc_fck);
omap2_init_common_devices(NULL, NULL);
}
+static struct gpio apollon_gpio_leds[] __initdata = {
+ { LED0_GPIO13, GPIOF_OUT_INIT_LOW, "LED0" }, /* LED0 - AA10 */
+ { LED1_GPIO14, GPIOF_OUT_INIT_LOW, "LED1" }, /* LED1 - AA6 */
+ { LED2_GPIO15, GPIOF_OUT_INIT_LOW, "LED2" }, /* LED2 - AA4 */
+};
+
static void __init apollon_led_init(void)
{
- /* LED0 - AA10 */
omap_mux_init_signal("vlynq_clk.gpio_13", 0);
- gpio_request(LED0_GPIO13, "LED0");
- gpio_direction_output(LED0_GPIO13, 0);
- /* LED1 - AA6 */
omap_mux_init_signal("vlynq_rx1.gpio_14", 0);
- gpio_request(LED1_GPIO14, "LED1");
- gpio_direction_output(LED1_GPIO14, 0);
- /* LED2 - AA4 */
omap_mux_init_signal("vlynq_rx0.gpio_15", 0);
- gpio_request(LED2_GPIO15, "LED2");
- gpio_direction_output(LED2_GPIO15, 0);
+
+ gpio_request_array(apollon_gpio_leds, ARRAY_SIZE(apollon_gpio_leds));
}
static void __init apollon_usb_init(void)
/* USB device */
/* DEVICE_SUSPEND */
omap_mux_init_signal("mcbsp2_clkx.gpio_12", 0);
- gpio_request(12, "USB suspend");
- gpio_direction_output(12, 0);
+ gpio_request_one(12, GPIOF_OUT_INIT_LOW, "USB suspend");
omap2_usbfs_init(&apollon_usb_config);
}
#include "mux.h"
#include "sdram-micron-mt46h32m32lf-6.h"
#include "hsmmc.h"
+#include "common-board-devices.h"
#define CM_T35_GPIO_PENDOWN 57
#if defined(CONFIG_SMSC911X) || defined(CONFIG_SMSC911X_MODULE)
#include <linux/smsc911x.h>
+#include <plat/gpmc-smsc911x.h>
-static struct smsc911x_platform_config cm_t35_smsc911x_config = {
- .irq_polarity = SMSC911X_IRQ_POLARITY_ACTIVE_LOW,
- .irq_type = SMSC911X_IRQ_TYPE_OPEN_DRAIN,
- .flags = SMSC911X_USE_32BIT | SMSC911X_SAVE_MAC_ADDRESS,
- .phy_interface = PHY_INTERFACE_MODE_MII,
-};
-
-static struct resource cm_t35_smsc911x_resources[] = {
- {
- .flags = IORESOURCE_MEM,
- },
- {
- .start = OMAP_GPIO_IRQ(CM_T35_SMSC911X_GPIO),
- .end = OMAP_GPIO_IRQ(CM_T35_SMSC911X_GPIO),
- .flags = IORESOURCE_IRQ | IORESOURCE_IRQ_LOWLEVEL,
- },
-};
-
-static struct platform_device cm_t35_smsc911x_device = {
- .name = "smsc911x",
+static struct omap_smsc911x_platform_data cm_t35_smsc911x_cfg = {
.id = 0,
- .num_resources = ARRAY_SIZE(cm_t35_smsc911x_resources),
- .resource = cm_t35_smsc911x_resources,
- .dev = {
- .platform_data = &cm_t35_smsc911x_config,
- },
-};
-
-static struct resource sb_t35_smsc911x_resources[] = {
- {
- .flags = IORESOURCE_MEM,
- },
- {
- .start = OMAP_GPIO_IRQ(SB_T35_SMSC911X_GPIO),
- .end = OMAP_GPIO_IRQ(SB_T35_SMSC911X_GPIO),
- .flags = IORESOURCE_IRQ | IORESOURCE_IRQ_LOWLEVEL,
- },
+ .cs = CM_T35_SMSC911X_CS,
+ .gpio_irq = CM_T35_SMSC911X_GPIO,
+ .gpio_reset = -EINVAL,
+ .flags = SMSC911X_USE_32BIT | SMSC911X_SAVE_MAC_ADDRESS,
};
-static struct platform_device sb_t35_smsc911x_device = {
- .name = "smsc911x",
+static struct omap_smsc911x_platform_data sb_t35_smsc911x_cfg = {
.id = 1,
- .num_resources = ARRAY_SIZE(sb_t35_smsc911x_resources),
- .resource = sb_t35_smsc911x_resources,
- .dev = {
- .platform_data = &cm_t35_smsc911x_config,
- },
+ .cs = SB_T35_SMSC911X_CS,
+ .gpio_irq = SB_T35_SMSC911X_GPIO,
+ .gpio_reset = -EINVAL,
+ .flags = SMSC911X_USE_32BIT | SMSC911X_SAVE_MAC_ADDRESS,
};
-static void __init cm_t35_init_smsc911x(struct platform_device *dev,
- int cs, int irq_gpio)
-{
- unsigned long cs_mem_base;
-
- if (gpmc_cs_request(cs, SZ_16M, &cs_mem_base) < 0) {
- pr_err("CM-T35: Failed request for GPMC mem for smsc911x\n");
- return;
- }
-
- dev->resource[0].start = cs_mem_base + 0x0;
- dev->resource[0].end = cs_mem_base + 0xff;
-
- if ((gpio_request(irq_gpio, "ETH IRQ") == 0) &&
- (gpio_direction_input(irq_gpio) == 0)) {
- gpio_export(irq_gpio, 0);
- } else {
- pr_err("CM-T35: could not obtain gpio for SMSC911X IRQ\n");
- return;
- }
-
- platform_device_register(dev);
-}
-
static void __init cm_t35_init_ethernet(void)
{
- cm_t35_init_smsc911x(&cm_t35_smsc911x_device,
- CM_T35_SMSC911X_CS, CM_T35_SMSC911X_GPIO);
- cm_t35_init_smsc911x(&sb_t35_smsc911x_device,
- SB_T35_SMSC911X_CS, SB_T35_SMSC911X_GPIO);
+ gpmc_smsc911x_init(&cm_t35_smsc911x_cfg);
+ gpmc_smsc911x_init(&sb_t35_smsc911x_cfg);
}
#else
static inline void __init cm_t35_init_ethernet(void) { return; }
static inline void cm_t35_init_nand(void) {}
#endif
-#if defined(CONFIG_TOUCHSCREEN_ADS7846) || \
- defined(CONFIG_TOUCHSCREEN_ADS7846_MODULE)
-#include <linux/spi/ads7846.h>
-
-static struct omap2_mcspi_device_config ads7846_mcspi_config = {
- .turbo_mode = 0,
- .single_channel = 1, /* 0: slave, 1: master */
-};
-
-static int ads7846_get_pendown_state(void)
-{
- return !gpio_get_value(CM_T35_GPIO_PENDOWN);
-}
-
-static struct ads7846_platform_data ads7846_config = {
- .x_max = 0x0fff,
- .y_max = 0x0fff,
- .x_plate_ohms = 180,
- .pressure_max = 255,
- .debounce_max = 10,
- .debounce_tol = 3,
- .debounce_rep = 1,
- .get_pendown_state = ads7846_get_pendown_state,
- .keep_vref_on = 1,
-};
-
-static struct spi_board_info cm_t35_spi_board_info[] __initdata = {
- {
- .modalias = "ads7846",
- .bus_num = 1,
- .chip_select = 0,
- .max_speed_hz = 1500000,
- .controller_data = &ads7846_mcspi_config,
- .irq = OMAP_GPIO_IRQ(CM_T35_GPIO_PENDOWN),
- .platform_data = &ads7846_config,
- },
-};
-
-static void __init cm_t35_init_ads7846(void)
-{
- if ((gpio_request(CM_T35_GPIO_PENDOWN, "ADS7846_PENDOWN") == 0) &&
- (gpio_direction_input(CM_T35_GPIO_PENDOWN) == 0)) {
- gpio_export(CM_T35_GPIO_PENDOWN, 0);
- } else {
- pr_err("CM-T35: could not obtain gpio for ADS7846_PENDOWN\n");
- return;
- }
-
- spi_register_board_info(cm_t35_spi_board_info,
- ARRAY_SIZE(cm_t35_spi_board_info));
-}
-#else
-static inline void cm_t35_init_ads7846(void) {}
-#endif
-
#define CM_T35_LCD_EN_GPIO 157
#define CM_T35_LCD_BL_GPIO 58
#define CM_T35_DVI_EN_GPIO 54
-static int lcd_bl_gpio;
-static int lcd_en_gpio;
-static int dvi_en_gpio;
-
static int lcd_enabled;
static int dvi_enabled;
return -EINVAL;
}
- gpio_set_value(lcd_en_gpio, 1);
- gpio_set_value(lcd_bl_gpio, 1);
+ gpio_set_value(CM_T35_LCD_EN_GPIO, 1);
+ gpio_set_value(CM_T35_LCD_BL_GPIO, 1);
lcd_enabled = 1;
{
lcd_enabled = 0;
- gpio_set_value(lcd_bl_gpio, 0);
- gpio_set_value(lcd_en_gpio, 0);
+ gpio_set_value(CM_T35_LCD_BL_GPIO, 0);
+ gpio_set_value(CM_T35_LCD_EN_GPIO, 0);
}
static int cm_t35_panel_enable_dvi(struct omap_dss_device *dssdev)
return -EINVAL;
}
- gpio_set_value(dvi_en_gpio, 0);
+ gpio_set_value(CM_T35_DVI_EN_GPIO, 0);
dvi_enabled = 1;
return 0;
static void cm_t35_panel_disable_dvi(struct omap_dss_device *dssdev)
{
- gpio_set_value(dvi_en_gpio, 1);
+ gpio_set_value(CM_T35_DVI_EN_GPIO, 1);
dvi_enabled = 0;
}
},
};
+static struct gpio cm_t35_dss_gpios[] __initdata = {
+ { CM_T35_LCD_EN_GPIO, GPIOF_OUT_INIT_LOW, "lcd enable" },
+ { CM_T35_LCD_BL_GPIO, GPIOF_OUT_INIT_LOW, "lcd bl enable" },
+ { CM_T35_DVI_EN_GPIO, GPIOF_OUT_INIT_HIGH, "dvi enable" },
+};
+
static void __init cm_t35_init_display(void)
{
int err;
- lcd_en_gpio = CM_T35_LCD_EN_GPIO;
- lcd_bl_gpio = CM_T35_LCD_BL_GPIO;
- dvi_en_gpio = CM_T35_DVI_EN_GPIO;
-
spi_register_board_info(cm_t35_lcd_spi_board_info,
ARRAY_SIZE(cm_t35_lcd_spi_board_info));
- err = gpio_request(lcd_en_gpio, "LCD RST");
- if (err) {
- pr_err("CM-T35: failed to get LCD reset GPIO\n");
- goto out;
- }
-
- err = gpio_request(lcd_bl_gpio, "LCD BL");
+ err = gpio_request_array(cm_t35_dss_gpios,
+ ARRAY_SIZE(cm_t35_dss_gpios));
if (err) {
- pr_err("CM-T35: failed to get LCD backlight control GPIO\n");
- goto err_lcd_bl;
- }
-
- err = gpio_request(dvi_en_gpio, "DVI EN");
- if (err) {
- pr_err("CM-T35: failed to get DVI reset GPIO\n");
- goto err_dvi_en;
+ pr_err("CM-T35: failed to request DSS control GPIOs\n");
+ return;
}
- gpio_export(lcd_en_gpio, 0);
- gpio_export(lcd_bl_gpio, 0);
- gpio_export(dvi_en_gpio, 0);
- gpio_direction_output(lcd_en_gpio, 0);
- gpio_direction_output(lcd_bl_gpio, 0);
- gpio_direction_output(dvi_en_gpio, 1);
+ gpio_export(CM_T35_LCD_EN_GPIO, 0);
+ gpio_export(CM_T35_LCD_BL_GPIO, 0);
+ gpio_export(CM_T35_DVI_EN_GPIO, 0);
msleep(50);
- gpio_set_value(lcd_en_gpio, 1);
+ gpio_set_value(CM_T35_LCD_EN_GPIO, 1);
err = omap_display_init(&cm_t35_dss_data);
if (err) {
pr_err("CM-T35: failed to register DSS device\n");
- goto err_dev_reg;
+ gpio_free_array(cm_t35_dss_gpios, ARRAY_SIZE(cm_t35_dss_gpios));
}
-
- return;
-
-err_dev_reg:
- gpio_free(dvi_en_gpio);
-err_dvi_en:
- gpio_free(lcd_bl_gpio);
-err_lcd_bl:
- gpio_free(lcd_en_gpio);
-out:
-
- return;
}
static struct regulator_consumer_supply cm_t35_vmmc1_supply = {
{
int wlan_rst = gpio + 2;
- if ((gpio_request(wlan_rst, "WLAN RST") == 0) &&
- (gpio_direction_output(wlan_rst, 1) == 0)) {
+ if (gpio_request_one(wlan_rst, GPIOF_OUT_INIT_HIGH, "WLAN RST") == 0) {
gpio_export(wlan_rst, 0);
-
udelay(10);
gpio_set_value(wlan_rst, 0);
udelay(10);
.vpll2 = &cm_t35_vpll2,
};
-static struct i2c_board_info __initdata cm_t35_i2c_boardinfo[] = {
- {
- I2C_BOARD_INFO("tps65930", 0x48),
- .flags = I2C_CLIENT_WAKE,
- .irq = INT_34XX_SYS_NIRQ,
- .platform_data = &cm_t35_twldata,
- },
-};
-
static void __init cm_t35_init_i2c(void)
{
- omap_register_i2c_bus(1, 2600, cm_t35_i2c_boardinfo,
- ARRAY_SIZE(cm_t35_i2c_boardinfo));
+ omap3_pmic_init("tps65930", &cm_t35_twldata);
}
static void __init cm_t35_init_early(void)
};
#endif
-static struct omap_musb_board_data musb_board_data = {
- .interface_type = MUSB_INTERFACE_ULPI,
- .mode = MUSB_OTG,
- .power = 100,
-};
-
static struct omap_board_config_kernel cm_t35_config[] __initdata = {
};
omap_serial_init();
cm_t35_init_i2c();
cm_t35_init_nand();
- cm_t35_init_ads7846();
+ omap_ads7846_init(1, CM_T35_GPIO_PENDOWN, 0, NULL);
cm_t35_init_ethernet();
cm_t35_init_led();
cm_t35_init_display();
- usb_musb_init(&musb_board_data);
+ usb_musb_init(NULL);
usbhs_init(&usbhs_bdata);
}
{
int err;
- err = gpio_request(RTC_CS_EN_GPIO, "rtc cs en");
+ err = gpio_request_one(RTC_CS_EN_GPIO, GPIOF_OUT_INIT_HIGH,
+ "rtc cs en");
if (err) {
pr_err("CM-T3517: rtc cs en gpio request failed: %d\n", err);
return;
}
- gpio_direction_output(RTC_CS_EN_GPIO, 1);
-
platform_device_register(&cm_t3517_rtc_device);
}
#else
{
int err;
- err = gpio_request(USB_HUB_RESET_GPIO, "usb hub rst");
+ err = gpio_request_one(USB_HUB_RESET_GPIO, GPIOF_OUT_INIT_LOW,
+ "usb hub rst");
if (err) {
pr_err("CM-T3517: usb hub rst gpio request failed: %d\n", err);
} else {
- gpio_direction_output(USB_HUB_RESET_GPIO, 0);
udelay(10);
gpio_set_value(USB_HUB_RESET_GPIO, 1);
msleep(1);
#include <plat/mcspi.h>
#include <linux/input/matrix_keypad.h>
#include <linux/spi/spi.h>
-#include <linux/spi/ads7846.h>
#include <linux/dm9000.h>
#include <linux/interrupt.h>
#include "mux.h"
#include "hsmmc.h"
#include "timer-gp.h"
+#include "common-board-devices.h"
#define NAND_BLOCK_SIZE SZ_128K
},
};
-static struct omap_nand_platform_data devkit8000_nand_data = {
- .options = NAND_BUSWIDTH_16,
- .parts = devkit8000_nand_partitions,
- .nr_parts = ARRAY_SIZE(devkit8000_nand_partitions),
- .dma_channel = -1, /* disable DMA in OMAP NAND driver */
-};
-
static struct omap2_hsmmc_info mmc[] = {
{
.mmc = 1,
/* TWL4030_GPIO_MAX + 0 is "LCD_PWREN" (out, active high) */
devkit8000_lcd_device.reset_gpio = gpio + TWL4030_GPIO_MAX + 0;
ret = gpio_request_one(devkit8000_lcd_device.reset_gpio,
- GPIOF_DIR_OUT | GPIOF_INIT_LOW, "LCD_PWREN");
+ GPIOF_OUT_INIT_LOW, "LCD_PWREN");
if (ret < 0) {
devkit8000_lcd_device.reset_gpio = -EINVAL;
printk(KERN_ERR "Failed to request GPIO for LCD_PWRN\n");
/* gpio + 7 is "DVI_PD" (out, active low) */
devkit8000_dvi_device.reset_gpio = gpio + 7;
ret = gpio_request_one(devkit8000_dvi_device.reset_gpio,
- GPIOF_DIR_OUT | GPIOF_INIT_LOW, "DVI PowerDown");
+ GPIOF_OUT_INIT_LOW, "DVI PowerDown");
if (ret < 0) {
devkit8000_dvi_device.reset_gpio = -EINVAL;
printk(KERN_ERR "Failed to request GPIO for DVI PowerDown\n");
.keypad = &devkit8000_kp_data,
};
-static struct i2c_board_info __initdata devkit8000_i2c_boardinfo[] = {
- {
- I2C_BOARD_INFO("tps65930", 0x48),
- .flags = I2C_CLIENT_WAKE,
- .irq = INT_34XX_SYS_NIRQ,
- .platform_data = &devkit8000_twldata,
- },
-};
-
static int __init devkit8000_i2c_init(void)
{
- omap_register_i2c_bus(1, 2600, devkit8000_i2c_boardinfo,
- ARRAY_SIZE(devkit8000_i2c_boardinfo));
+ omap3_pmic_init("tps65930", &devkit8000_twldata);
/* Bus 3 is attached to the DVI port where devices like the pico DLP
* projector don't work reliably with 400kHz */
omap_register_i2c_bus(3, 400, NULL, 0);
#endif
}
-static void __init devkit8000_ads7846_init(void)
-{
- int gpio = OMAP3_DEVKIT_TS_GPIO;
- int ret;
-
- ret = gpio_request(gpio, "ads7846_pen_down");
- if (ret < 0) {
- printk(KERN_ERR "Failed to request GPIO %d for "
- "ads7846 pen down IRQ\n", gpio);
- return;
- }
-
- gpio_direction_input(gpio);
-}
-
-static int ads7846_get_pendown_state(void)
-{
- return !gpio_get_value(OMAP3_DEVKIT_TS_GPIO);
-}
-
-static struct ads7846_platform_data ads7846_config = {
- .x_max = 0x0fff,
- .y_max = 0x0fff,
- .x_plate_ohms = 180,
- .pressure_max = 255,
- .debounce_max = 10,
- .debounce_tol = 5,
- .debounce_rep = 1,
- .get_pendown_state = ads7846_get_pendown_state,
- .keep_vref_on = 1,
- .settle_delay_usecs = 150,
-};
-
-static struct omap2_mcspi_device_config ads7846_mcspi_config = {
- .turbo_mode = 0,
- .single_channel = 1, /* 0: slave, 1: master */
-};
-
-static struct spi_board_info devkit8000_spi_board_info[] __initdata = {
- {
- .modalias = "ads7846",
- .bus_num = 2,
- .chip_select = 0,
- .max_speed_hz = 1500000,
- .controller_data = &ads7846_mcspi_config,
- .irq = OMAP_GPIO_IRQ(OMAP3_DEVKIT_TS_GPIO),
- .platform_data = &ads7846_config,
- }
-};
-
#define OMAP_DM9000_BASE 0x2c000000
static struct resource omap_dm9000_resources[] = {
{
unsigned char *eth_addr = omap_dm9000_platdata.dev_addr;
struct omap_die_id odi;
+ int ret;
- if (gpio_request(OMAP_DM9000_GPIO_IRQ, "dm9000 irq") < 0) {
+ ret = gpio_request_one(OMAP_DM9000_GPIO_IRQ, GPIOF_IN, "dm9000 irq");
+ if (ret < 0) {
printk(KERN_ERR "Failed to request GPIO%d for dm9000 IRQ\n",
OMAP_DM9000_GPIO_IRQ);
return;
- }
-
- gpio_direction_input(OMAP_DM9000_GPIO_IRQ);
+ }
/* init the mac address using DIE id */
omap_get_die_id(&odi);
&omap_dm9000_dev,
};
-static void __init devkit8000_flash_init(void)
-{
- u8 cs = 0;
- u8 nandcs = GPMC_CS_NUM + 1;
-
- /* find out the chip-select on which NAND exists */
- while (cs < GPMC_CS_NUM) {
- u32 ret = 0;
- ret = gpmc_cs_read_reg(cs, GPMC_CS_CONFIG1);
-
- if ((ret & 0xC00) == 0x800) {
- printk(KERN_INFO "Found NAND on CS%d\n", cs);
- if (nandcs > GPMC_CS_NUM)
- nandcs = cs;
- }
- cs++;
- }
-
- if (nandcs > GPMC_CS_NUM) {
- printk(KERN_INFO "NAND: Unable to find configuration "
- "in GPMC\n ");
- return;
- }
-
- if (nandcs < GPMC_CS_NUM) {
- devkit8000_nand_data.cs = nandcs;
-
- printk(KERN_INFO "Registering NAND on CS%d\n", nandcs);
- if (gpmc_nand_init(&devkit8000_nand_data) < 0)
- printk(KERN_ERR "Unable to register NAND device\n");
- }
-}
-
-static struct omap_musb_board_data musb_board_data = {
- .interface_type = MUSB_INTERFACE_ULPI,
- .mode = MUSB_OTG,
- .power = 100,
-};
-
static const struct usbhs_omap_board_data usbhs_bdata __initconst = {
.port_mode[0] = OMAP_EHCI_PORT_MODE_PHY,
ARRAY_SIZE(devkit8000_devices));
omap_display_init(&devkit8000_dss_data);
- spi_register_board_info(devkit8000_spi_board_info,
- ARRAY_SIZE(devkit8000_spi_board_info));
- devkit8000_ads7846_init();
+ omap_ads7846_init(2, OMAP3_DEVKIT_TS_GPIO, 0, NULL);
- usb_musb_init(&musb_board_data);
+ usb_musb_init(NULL);
usbhs_init(&usbhs_bdata);
- devkit8000_flash_init();
+ omap_nand_flash_init(NAND_BUSWIDTH_16, devkit8000_nand_partitions,
+ ARRAY_SIZE(devkit8000_nand_partitions));
/* Ensure SDRC pins are mux'd for self-refresh */
omap_mux_init_signal("sdrc_cke0", OMAP_PIN_OUTPUT);
#include "mux.h"
#include "hsmmc.h"
#include "sdram-numonyx-m65kxxxxam.h"
+#include "common-board-devices.h"
#define IGEP2_SMSC911X_CS 5
#define IGEP2_SMSC911X_GPIO 176
#define IGEP2_RC_GPIO_WIFI_NRESET 139
#define IGEP2_RC_GPIO_BT_NRESET 137
+#define IGEP3_GPIO_LED0_GREEN 54
+#define IGEP3_GPIO_LED0_RED 53
+#define IGEP3_GPIO_LED1_RED 16
+#define IGEP3_GPIO_USBH_NRESET 183
+
/*
* IGEP2 Hardware Revision Table
*
#define IGEP2_BOARD_HWREV_B 0
#define IGEP2_BOARD_HWREV_C 1
+#define IGEP3_BOARD_HWREV 2
static u8 hwrev;
{
u8 ret;
+ if (machine_is_igep0030()) {
+ hwrev = IGEP3_BOARD_HWREV;
+ return;
+ }
+
omap_mux_init_gpio(IGEP2_GPIO_LED1_RED, OMAP_PIN_INPUT);
- if ((gpio_request(IGEP2_GPIO_LED1_RED, "GPIO_HW0_REV") == 0) &&
- (gpio_direction_input(IGEP2_GPIO_LED1_RED) == 0)) {
- ret = gpio_get_value(IGEP2_GPIO_LED1_RED);
- if (ret == 0) {
- pr_info("IGEP2: Hardware Revision C (B-NON compatible)\n");
- hwrev = IGEP2_BOARD_HWREV_C;
- } else if (ret == 1) {
- pr_info("IGEP2: Hardware Revision B/C (B compatible)\n");
- hwrev = IGEP2_BOARD_HWREV_B;
- } else {
- pr_err("IGEP2: Unknown Hardware Revision\n");
- hwrev = -1;
- }
- } else {
+ if (gpio_request_one(IGEP2_GPIO_LED1_RED, GPIOF_IN, "GPIO_HW0_REV")) {
pr_warning("IGEP2: Could not obtain gpio GPIO_HW0_REV\n");
pr_err("IGEP2: Unknown Hardware Revision\n");
+ return;
+ }
+
+ ret = gpio_get_value(IGEP2_GPIO_LED1_RED);
+ if (ret == 0) {
+ pr_info("IGEP2: Hardware Revision C (B-NON compatible)\n");
+ hwrev = IGEP2_BOARD_HWREV_C;
+ } else if (ret == 1) {
+ pr_info("IGEP2: Hardware Revision B/C (B compatible)\n");
+ hwrev = IGEP2_BOARD_HWREV_B;
+ } else {
+ pr_err("IGEP2: Unknown Hardware Revision\n");
+ hwrev = -1;
}
gpio_free(IGEP2_GPIO_LED1_RED);
* So MTD regards it as 4KiB page size and 256KiB block size 64*(2*2048)
*/
-static struct mtd_partition igep2_onenand_partitions[] = {
+static struct mtd_partition igep_onenand_partitions[] = {
{
.name = "X-Loader",
.offset = 0,
},
};
-static struct omap_onenand_platform_data igep2_onenand_data = {
- .parts = igep2_onenand_partitions,
- .nr_parts = ARRAY_SIZE(igep2_onenand_partitions),
+static struct omap_onenand_platform_data igep_onenand_data = {
+ .parts = igep_onenand_partitions,
+ .nr_parts = ARRAY_SIZE(igep_onenand_partitions),
.dma_channel = -1, /* disable DMA in OMAP OneNAND driver */
};
-static struct platform_device igep2_onenand_device = {
+static struct platform_device igep_onenand_device = {
.name = "omap2-onenand",
.id = -1,
.dev = {
- .platform_data = &igep2_onenand_data,
+ .platform_data = &igep_onenand_data,
},
};
-static void __init igep2_flash_init(void)
+static void __init igep_flash_init(void)
{
u8 cs = 0;
u8 onenandcs = GPMC_CS_NUM + 1;
/* Check if NAND/oneNAND is configured */
if ((ret & 0xC00) == 0x800)
/* NAND found */
- pr_err("IGEP2: Unsupported NAND found\n");
+ pr_err("IGEP: Unsupported NAND found\n");
else {
ret = gpmc_cs_read_reg(cs, GPMC_CS_CONFIG7);
if ((ret & 0x3F) == (ONENAND_MAP >> 24))
}
if (onenandcs > GPMC_CS_NUM) {
- pr_err("IGEP2: Unable to find configuration in GPMC\n");
+ pr_err("IGEP: Unable to find configuration in GPMC\n");
return;
}
- igep2_onenand_data.cs = onenandcs;
+ igep_onenand_data.cs = onenandcs;
- if (platform_device_register(&igep2_onenand_device) < 0)
- pr_err("IGEP2: Unable to register OneNAND device\n");
+ if (platform_device_register(&igep_onenand_device) < 0)
+ pr_err("IGEP: Unable to register OneNAND device\n");
}
#else
-static void __init igep2_flash_init(void) {}
+static void __init igep_flash_init(void) {}
#endif
#if defined(CONFIG_SMSC911X) || defined(CONFIG_SMSC911X_MODULE)
#include <linux/smsc911x.h>
+#include <plat/gpmc-smsc911x.h>
-static struct smsc911x_platform_config igep2_smsc911x_config = {
- .irq_polarity = SMSC911X_IRQ_POLARITY_ACTIVE_LOW,
- .irq_type = SMSC911X_IRQ_TYPE_OPEN_DRAIN,
- .flags = SMSC911X_USE_32BIT | SMSC911X_SAVE_MAC_ADDRESS ,
- .phy_interface = PHY_INTERFACE_MODE_MII,
-};
-
-static struct resource igep2_smsc911x_resources[] = {
- {
- .flags = IORESOURCE_MEM,
- },
- {
- .start = OMAP_GPIO_IRQ(IGEP2_SMSC911X_GPIO),
- .end = OMAP_GPIO_IRQ(IGEP2_SMSC911X_GPIO),
- .flags = IORESOURCE_IRQ | IORESOURCE_IRQ_LOWLEVEL,
- },
-};
-
-static struct platform_device igep2_smsc911x_device = {
- .name = "smsc911x",
- .id = 0,
- .num_resources = ARRAY_SIZE(igep2_smsc911x_resources),
- .resource = igep2_smsc911x_resources,
- .dev = {
- .platform_data = &igep2_smsc911x_config,
- },
+static struct omap_smsc911x_platform_data smsc911x_cfg = {
+ .cs = IGEP2_SMSC911X_CS,
+ .gpio_irq = IGEP2_SMSC911X_GPIO,
+ .gpio_reset = -EINVAL,
+ .flags = SMSC911X_USE_32BIT | SMSC911X_SAVE_MAC_ADDRESS,
};
static inline void __init igep2_init_smsc911x(void)
{
- unsigned long cs_mem_base;
-
- if (gpmc_cs_request(IGEP2_SMSC911X_CS, SZ_16M, &cs_mem_base) < 0) {
- pr_err("IGEP v2: Failed request for GPMC mem for smsc911x\n");
- gpmc_cs_free(IGEP2_SMSC911X_CS);
- return;
- }
-
- igep2_smsc911x_resources[0].start = cs_mem_base + 0x0;
- igep2_smsc911x_resources[0].end = cs_mem_base + 0xff;
-
- if ((gpio_request(IGEP2_SMSC911X_GPIO, "SMSC911X IRQ") == 0) &&
- (gpio_direction_input(IGEP2_SMSC911X_GPIO) == 0)) {
- gpio_export(IGEP2_SMSC911X_GPIO, 0);
- } else {
- pr_err("IGEP v2: Could not obtain gpio for for SMSC911X IRQ\n");
- return;
- }
-
- platform_device_register(&igep2_smsc911x_device);
+ gpmc_smsc911x_init(&smsc911x_cfg);
}
#else
static inline void __init igep2_init_smsc911x(void) { }
#endif
-static struct regulator_consumer_supply igep2_vmmc1_supply =
+static struct regulator_consumer_supply igep_vmmc1_supply =
REGULATOR_SUPPLY("vmmc", "omap_hsmmc.0");
/* VMMC1 for OMAP VDD_MMC1 (i/o) and MMC1 card */
-static struct regulator_init_data igep2_vmmc1 = {
+static struct regulator_init_data igep_vmmc1 = {
.constraints = {
.min_uV = 1850000,
.max_uV = 3150000,
| REGULATOR_CHANGE_STATUS,
},
.num_consumer_supplies = 1,
- .consumer_supplies = &igep2_vmmc1_supply,
+ .consumer_supplies = &igep_vmmc1_supply,
};
-static struct regulator_consumer_supply igep2_vio_supply =
+static struct regulator_consumer_supply igep_vio_supply =
REGULATOR_SUPPLY("vmmc_aux", "omap_hsmmc.1");
-static struct regulator_init_data igep2_vio = {
+static struct regulator_init_data igep_vio = {
.constraints = {
.min_uV = 1800000,
.max_uV = 1800000,
| REGULATOR_CHANGE_STATUS,
},
.num_consumer_supplies = 1,
- .consumer_supplies = &igep2_vio_supply,
+ .consumer_supplies = &igep_vio_supply,
};
-static struct regulator_consumer_supply igep2_vmmc2_supply =
+static struct regulator_consumer_supply igep_vmmc2_supply =
REGULATOR_SUPPLY("vmmc", "omap_hsmmc.1");
-static struct regulator_init_data igep2_vmmc2 = {
+static struct regulator_init_data igep_vmmc2 = {
.constraints = {
.valid_modes_mask = REGULATOR_MODE_NORMAL,
.always_on = 1,
},
.num_consumer_supplies = 1,
- .consumer_supplies = &igep2_vmmc2_supply,
+ .consumer_supplies = &igep_vmmc2_supply,
};
-static struct fixed_voltage_config igep2_vwlan = {
+static struct fixed_voltage_config igep_vwlan = {
.supply_name = "vwlan",
.microvolts = 3300000,
.gpio = -EINVAL,
.enabled_at_boot = 1,
- .init_data = &igep2_vmmc2,
+ .init_data = &igep_vmmc2,
};
-static struct platform_device igep2_vwlan_device = {
+static struct platform_device igep_vwlan_device = {
.name = "reg-fixed-voltage",
.id = 0,
.dev = {
- .platform_data = &igep2_vwlan,
+ .platform_data = &igep_vwlan,
},
};
#if defined(CONFIG_LEDS_GPIO) || defined(CONFIG_LEDS_GPIO_MODULE)
#include <linux/leds.h>
-static struct gpio_led igep2_gpio_leds[] = {
+static struct gpio_led igep_gpio_leds[] = {
[0] = {
.name = "gpio-led:red:d0",
- .gpio = IGEP2_GPIO_LED0_RED,
.default_trigger = "default-off"
},
[1] = {
.name = "gpio-led:green:d0",
- .gpio = IGEP2_GPIO_LED0_GREEN,
.default_trigger = "default-off",
},
[2] = {
.name = "gpio-led:red:d1",
- .gpio = IGEP2_GPIO_LED1_RED,
.default_trigger = "default-off",
},
[3] = {
},
};
-static struct gpio_led_platform_data igep2_led_pdata = {
- .leds = igep2_gpio_leds,
- .num_leds = ARRAY_SIZE(igep2_gpio_leds),
+static struct gpio_led_platform_data igep_led_pdata = {
+ .leds = igep_gpio_leds,
+ .num_leds = ARRAY_SIZE(igep_gpio_leds),
};
-static struct platform_device igep2_led_device = {
+static struct platform_device igep_led_device = {
.name = "leds-gpio",
.id = -1,
.dev = {
- .platform_data = &igep2_led_pdata,
+ .platform_data = &igep_led_pdata,
},
};
-static void __init igep2_leds_init(void)
+static void __init igep_leds_init(void)
{
- platform_device_register(&igep2_led_device);
+ if (machine_is_igep0020()) {
+ igep_gpio_leds[0].gpio = IGEP2_GPIO_LED0_RED;
+ igep_gpio_leds[1].gpio = IGEP2_GPIO_LED0_GREEN;
+ igep_gpio_leds[2].gpio = IGEP2_GPIO_LED1_RED;
+ } else {
+ igep_gpio_leds[0].gpio = IGEP3_GPIO_LED0_RED;
+ igep_gpio_leds[1].gpio = IGEP3_GPIO_LED0_GREEN;
+ igep_gpio_leds[2].gpio = IGEP3_GPIO_LED1_RED;
+ }
+
+ platform_device_register(&igep_led_device);
}
#else
-static inline void igep2_leds_init(void)
+static struct gpio igep_gpio_leds[] __initdata = {
+ { -EINVAL, GPIOF_OUT_INIT_LOW, "gpio-led:red:d0" },
+ { -EINVAL, GPIOF_OUT_INIT_LOW, "gpio-led:green:d0" },
+ { -EINVAL, GPIOF_OUT_INIT_LOW, "gpio-led:red:d1" },
+};
+
+static inline void igep_leds_init(void)
{
- if ((gpio_request(IGEP2_GPIO_LED0_RED, "gpio-led:red:d0") == 0) &&
- (gpio_direction_output(IGEP2_GPIO_LED0_RED, 0) == 0))
- gpio_export(IGEP2_GPIO_LED0_RED, 0);
- else
- pr_warning("IGEP v2: Could not obtain gpio GPIO_LED0_RED\n");
+ int i;
- if ((gpio_request(IGEP2_GPIO_LED0_GREEN, "gpio-led:green:d0") == 0) &&
- (gpio_direction_output(IGEP2_GPIO_LED0_GREEN, 0) == 0))
- gpio_export(IGEP2_GPIO_LED0_GREEN, 0);
- else
- pr_warning("IGEP v2: Could not obtain gpio GPIO_LED0_GREEN\n");
+ if (machine_is_igep0020()) {
+ igep_gpio_leds[0].gpio = IGEP2_GPIO_LED0_RED;
+ igep_gpio_leds[1].gpio = IGEP2_GPIO_LED0_GREEN;
+ igep_gpio_leds[2].gpio = IGEP2_GPIO_LED1_RED;
+ } else {
+ igep_gpio_leds[0].gpio = IGEP3_GPIO_LED0_RED;
+ igep_gpio_leds[1].gpio = IGEP3_GPIO_LED0_GREEN;
+ igep_gpio_leds[2].gpio = IGEP3_GPIO_LED1_RED;
+ }
- if ((gpio_request(IGEP2_GPIO_LED1_RED, "gpio-led:red:d1") == 0) &&
- (gpio_direction_output(IGEP2_GPIO_LED1_RED, 0) == 0))
- gpio_export(IGEP2_GPIO_LED1_RED, 0);
- else
- pr_warning("IGEP v2: Could not obtain gpio GPIO_LED1_RED\n");
+ if (gpio_request_array(igep_gpio_leds, ARRAY_SIZE(igep_gpio_leds))) {
+ pr_warning("IGEP v2: Could not obtain leds gpios\n");
+ return;
+ }
+ for (i = 0; i < ARRAY_SIZE(igep_gpio_leds); i++)
+ gpio_export(igep_gpio_leds[i].gpio, 0);
}
#endif
-static int igep2_twl_gpio_setup(struct device *dev,
+static struct gpio igep2_twl_gpios[] = {
+ { -EINVAL, GPIOF_IN, "GPIO_EHCI_NOC" },
+ { -EINVAL, GPIOF_OUT_INIT_LOW, "GPIO_USBH_CPEN" },
+};
+
+static int igep_twl_gpio_setup(struct device *dev,
unsigned gpio, unsigned ngpio)
{
+ int ret;
+
/* gpio + 0 is "mmc0_cd" (input/IRQ) */
mmc[0].gpio_cd = gpio + 0;
omap2_hsmmc_init(mmc);
- /*
- * REVISIT: need ehci-omap hooks for external VBUS
- * power switch and overcurrent detect
- */
- if ((gpio_request(gpio + 1, "GPIO_EHCI_NOC") < 0) ||
- (gpio_direction_input(gpio + 1) < 0))
- pr_err("IGEP2: Could not obtain gpio for EHCI NOC");
-
- /*
- * TWL4030_GPIO_MAX + 0 == ledA, GPIO_USBH_CPEN
- * (out, active low)
- */
- if ((gpio_request(gpio + TWL4030_GPIO_MAX, "GPIO_USBH_CPEN") < 0) ||
- (gpio_direction_output(gpio + TWL4030_GPIO_MAX, 0) < 0))
- pr_err("IGEP2: Could not obtain gpio for USBH_CPEN");
-
/* TWL4030_GPIO_MAX + 1 == ledB (out, active low LED) */
#if !defined(CONFIG_LEDS_GPIO) && !defined(CONFIG_LEDS_GPIO_MODULE)
- if ((gpio_request(gpio+TWL4030_GPIO_MAX+1, "gpio-led:green:d1") == 0)
- && (gpio_direction_output(gpio + TWL4030_GPIO_MAX + 1, 1) == 0))
+ ret = gpio_request_one(gpio + TWL4030_GPIO_MAX + 1, GPIOF_OUT_INIT_HIGH,
+ "gpio-led:green:d1");
+ if (ret == 0)
gpio_export(gpio + TWL4030_GPIO_MAX + 1, 0);
else
- pr_warning("IGEP v2: Could not obtain gpio GPIO_LED1_GREEN\n");
+ pr_warning("IGEP: Could not obtain gpio GPIO_LED1_GREEN\n");
#else
- igep2_gpio_leds[3].gpio = gpio + TWL4030_GPIO_MAX + 1;
+ igep_gpio_leds[3].gpio = gpio + TWL4030_GPIO_MAX + 1;
#endif
+ if (machine_is_igep0030())
+ return 0;
+
+ /*
+ * REVISIT: need ehci-omap hooks for external VBUS
+ * power switch and overcurrent detect
+ */
+ igep2_twl_gpios[0].gpio = gpio + 1;
+
+ /* TWL4030_GPIO_MAX + 0 == ledA, GPIO_USBH_CPEN (out, active low) */
+ igep2_twl_gpios[1].gpio = gpio + TWL4030_GPIO_MAX;
+
+ ret = gpio_request_array(igep2_twl_gpios, ARRAY_SIZE(igep2_twl_gpios));
+ if (ret < 0)
+ pr_err("IGEP2: Could not obtain gpio for USBH_CPEN");
+
return 0;
};
-static struct twl4030_gpio_platform_data igep2_twl4030_gpio_pdata = {
+static struct twl4030_gpio_platform_data igep_twl4030_gpio_pdata = {
.gpio_base = OMAP_MAX_GPIO_LINES,
.irq_base = TWL4030_GPIO_IRQ_BASE,
.irq_end = TWL4030_GPIO_IRQ_END,
.use_leds = true,
- .setup = igep2_twl_gpio_setup,
+ .setup = igep_twl_gpio_setup,
};
-static struct twl4030_usb_data igep2_usb_data = {
+static struct twl4030_usb_data igep_usb_data = {
.usb_mode = T2_USB_MODE_ULPI,
};
static void __init igep2_display_init(void)
{
- if (gpio_request(IGEP2_GPIO_DVI_PUP, "GPIO_DVI_PUP") &&
- gpio_direction_output(IGEP2_GPIO_DVI_PUP, 1))
+ int err = gpio_request_one(IGEP2_GPIO_DVI_PUP, GPIOF_OUT_INIT_HIGH,
+ "GPIO_DVI_PUP");
+ if (err)
pr_err("IGEP v2: Could not obtain gpio GPIO_DVI_PUP\n");
}
-static struct platform_device *igep2_devices[] __initdata = {
- &igep2_vwlan_device,
+static struct platform_device *igep_devices[] __initdata = {
+ &igep_vwlan_device,
};
-static void __init igep2_init_early(void)
+static void __init igep_init_early(void)
{
omap2_init_common_infrastructure();
omap2_init_common_devices(m65kxxxxam_sdrc_params,
.rep = 1,
};
-static struct twl4030_platform_data igep2_twldata = {
+static struct twl4030_platform_data igep_twldata = {
.irq_base = TWL4030_IRQ_BASE,
.irq_end = TWL4030_IRQ_END,
/* platform_data for children goes here */
- .usb = &igep2_usb_data,
- .codec = &igep2_codec_data,
- .gpio = &igep2_twl4030_gpio_pdata,
- .keypad = &igep2_keypad_pdata,
- .vmmc1 = &igep2_vmmc1,
- .vpll2 = &igep2_vpll2,
- .vio = &igep2_vio,
-};
-
-static struct i2c_board_info __initdata igep2_i2c1_boardinfo[] = {
- {
- I2C_BOARD_INFO("twl4030", 0x48),
- .flags = I2C_CLIENT_WAKE,
- .irq = INT_34XX_SYS_NIRQ,
- .platform_data = &igep2_twldata,
- },
+ .usb = &igep_usb_data,
+ .gpio = &igep_twl4030_gpio_pdata,
+ .vmmc1 = &igep_vmmc1,
+ .vio = &igep_vio,
};
static struct i2c_board_info __initdata igep2_i2c3_boardinfo[] = {
},
};
-static void __init igep2_i2c_init(void)
+static void __init igep_i2c_init(void)
{
int ret;
- ret = omap_register_i2c_bus(1, 2600, igep2_i2c1_boardinfo,
- ARRAY_SIZE(igep2_i2c1_boardinfo));
- if (ret)
- pr_warning("IGEP2: Could not register I2C1 bus (%d)\n", ret);
+ if (machine_is_igep0020()) {
+ /*
+ * Bus 3 is attached to the DVI port where devices like the
+ * pico DLP projector don't work reliably with 400kHz
+ */
+ ret = omap_register_i2c_bus(3, 100, igep2_i2c3_boardinfo,
+ ARRAY_SIZE(igep2_i2c3_boardinfo));
+ if (ret)
+ pr_warning("IGEP2: Could not register I2C3 bus (%d)\n", ret);
+
+ igep_twldata.codec = &igep2_codec_data;
+ igep_twldata.keypad = &igep2_keypad_pdata;
+ igep_twldata.vpll2 = &igep2_vpll2;
+ }
- /*
- * Bus 3 is attached to the DVI port where devices like the pico DLP
- * projector don't work reliably with 400kHz
- */
- ret = omap_register_i2c_bus(3, 100, igep2_i2c3_boardinfo,
- ARRAY_SIZE(igep2_i2c3_boardinfo));
- if (ret)
- pr_warning("IGEP2: Could not register I2C3 bus (%d)\n", ret);
+ omap3_pmic_init("twl4030", &igep_twldata);
}
-static struct omap_musb_board_data musb_board_data = {
- .interface_type = MUSB_INTERFACE_ULPI,
- .mode = MUSB_OTG,
- .power = 100,
-};
-
-static const struct usbhs_omap_board_data usbhs_bdata __initconst = {
+static const struct usbhs_omap_board_data igep2_usbhs_bdata __initconst = {
.port_mode[0] = OMAP_EHCI_PORT_MODE_PHY,
.port_mode[1] = OMAP_USBHS_PORT_MODE_UNUSED,
.port_mode[2] = OMAP_USBHS_PORT_MODE_UNUSED,
.reset_gpio_port[2] = -EINVAL,
};
+static const struct usbhs_omap_board_data igep3_usbhs_bdata __initconst = {
+ .port_mode[0] = OMAP_USBHS_PORT_MODE_UNUSED,
+ .port_mode[1] = OMAP_EHCI_PORT_MODE_PHY,
+ .port_mode[2] = OMAP_USBHS_PORT_MODE_UNUSED,
+
+ .phy_reset = true,
+ .reset_gpio_port[0] = -EINVAL,
+ .reset_gpio_port[1] = IGEP3_GPIO_USBH_NRESET,
+ .reset_gpio_port[2] = -EINVAL,
+};
+
#ifdef CONFIG_OMAP_MUX
static struct omap_board_mux board_mux[] __initdata = {
{ .reg_offset = OMAP_MUX_TERMINATOR },
#endif
#if defined(CONFIG_LIBERTAS_SDIO) || defined(CONFIG_LIBERTAS_SDIO_MODULE)
+static struct gpio igep_wlan_bt_gpios[] __initdata = {
+ { -EINVAL, GPIOF_OUT_INIT_HIGH, "GPIO_WIFI_NPD" },
+ { -EINVAL, GPIOF_OUT_INIT_HIGH, "GPIO_WIFI_NRESET" },
+ { -EINVAL, GPIOF_OUT_INIT_HIGH, "GPIO_BT_NRESET" },
+};
-static void __init igep2_wlan_bt_init(void)
+static void __init igep_wlan_bt_init(void)
{
- unsigned npd, wreset, btreset;
+ int err;
/* GPIO's for WLAN-BT combo depends on hardware revision */
if (hwrev == IGEP2_BOARD_HWREV_B) {
- npd = IGEP2_RB_GPIO_WIFI_NPD;
- wreset = IGEP2_RB_GPIO_WIFI_NRESET;
- btreset = IGEP2_RB_GPIO_BT_NRESET;
- } else if (hwrev == IGEP2_BOARD_HWREV_C) {
- npd = IGEP2_RC_GPIO_WIFI_NPD;
- wreset = IGEP2_RC_GPIO_WIFI_NRESET;
- btreset = IGEP2_RC_GPIO_BT_NRESET;
+ igep_wlan_bt_gpios[0].gpio = IGEP2_RB_GPIO_WIFI_NPD;
+ igep_wlan_bt_gpios[1].gpio = IGEP2_RB_GPIO_WIFI_NRESET;
+ igep_wlan_bt_gpios[2].gpio = IGEP2_RB_GPIO_BT_NRESET;
+ } else if (hwrev == IGEP2_BOARD_HWREV_C || machine_is_igep0030()) {
+ igep_wlan_bt_gpios[0].gpio = IGEP2_RC_GPIO_WIFI_NPD;
+ igep_wlan_bt_gpios[1].gpio = IGEP2_RC_GPIO_WIFI_NRESET;
+ igep_wlan_bt_gpios[2].gpio = IGEP2_RC_GPIO_BT_NRESET;
} else
return;
- /* Set GPIO's for WLAN-BT combo module */
- if ((gpio_request(npd, "GPIO_WIFI_NPD") == 0) &&
- (gpio_direction_output(npd, 1) == 0)) {
- gpio_export(npd, 0);
- } else
- pr_warning("IGEP2: Could not obtain gpio GPIO_WIFI_NPD\n");
-
- if ((gpio_request(wreset, "GPIO_WIFI_NRESET") == 0) &&
- (gpio_direction_output(wreset, 1) == 0)) {
- gpio_export(wreset, 0);
- gpio_set_value(wreset, 0);
- udelay(10);
- gpio_set_value(wreset, 1);
- } else
- pr_warning("IGEP2: Could not obtain gpio GPIO_WIFI_NRESET\n");
+ err = gpio_request_array(igep_wlan_bt_gpios,
+ ARRAY_SIZE(igep_wlan_bt_gpios));
+ if (err) {
+ pr_warning("IGEP2: Could not obtain WIFI/BT gpios\n");
+ return;
+ }
+
+ gpio_export(igep_wlan_bt_gpios[0].gpio, 0);
+ gpio_export(igep_wlan_bt_gpios[1].gpio, 0);
+ gpio_export(igep_wlan_bt_gpios[2].gpio, 0);
+
+ gpio_set_value(igep_wlan_bt_gpios[1].gpio, 0);
+ udelay(10);
+ gpio_set_value(igep_wlan_bt_gpios[1].gpio, 1);
- if ((gpio_request(btreset, "GPIO_BT_NRESET") == 0) &&
- (gpio_direction_output(btreset, 1) == 0)) {
- gpio_export(btreset, 0);
- } else
- pr_warning("IGEP2: Could not obtain gpio GPIO_BT_NRESET\n");
}
#else
-static inline void __init igep2_wlan_bt_init(void) { }
+static inline void __init igep_wlan_bt_init(void) { }
#endif
-static void __init igep2_init(void)
+static void __init igep_init(void)
{
omap3_mux_init(board_mux, OMAP_PACKAGE_CBB);
/* Get IGEP2 hardware revision */
igep2_get_revision();
/* Register I2C busses and drivers */
- igep2_i2c_init();
- platform_add_devices(igep2_devices, ARRAY_SIZE(igep2_devices));
- omap_display_init(&igep2_dss_data);
+ igep_i2c_init();
+ platform_add_devices(igep_devices, ARRAY_SIZE(igep_devices));
omap_serial_init();
- usb_musb_init(&musb_board_data);
- usbhs_init(&usbhs_bdata);
+ usb_musb_init(NULL);
- igep2_flash_init();
- igep2_leds_init();
- igep2_display_init();
- igep2_init_smsc911x();
+ igep_flash_init();
+ igep_leds_init();
/*
* WLAN-BT combo module from MuRata which has a Marvell WLAN
* (88W8686) + CSR Bluetooth chipset. Uses SDIO interface.
*/
- igep2_wlan_bt_init();
+ igep_wlan_bt_init();
+ if (machine_is_igep0020()) {
+ omap_display_init(&igep2_dss_data);
+ igep2_display_init();
+ igep2_init_smsc911x();
+ usbhs_init(&igep2_usbhs_bdata);
+ } else {
+ usbhs_init(&igep3_usbhs_bdata);
+ }
}
MACHINE_START(IGEP0020, "IGEP v2 board")
.boot_params = 0x80000100,
.reserve = omap_reserve,
.map_io = omap3_map_io,
- .init_early = igep2_init_early,
+ .init_early = igep_init_early,
+ .init_irq = omap_init_irq,
+ .init_machine = igep_init,
+ .timer = &omap_timer,
+MACHINE_END
+
+MACHINE_START(IGEP0030, "IGEP OMAP3 module")
+ .boot_params = 0x80000100,
+ .reserve = omap_reserve,
+ .map_io = omap3_map_io,
+ .init_early = igep_init_early,
.init_irq = omap_init_irq,
- .init_machine = igep2_init,
+ .init_machine = igep_init,
.timer = &omap_timer,
MACHINE_END
+++ /dev/null
-/*
- * Copyright (C) 2010 - ISEE 2007 SL
- *
- * Modified from mach-omap2/board-generic.c
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License version 2 as
- * published by the Free Software Foundation.
- */
-
-#include <linux/kernel.h>
-#include <linux/init.h>
-#include <linux/platform_device.h>
-#include <linux/delay.h>
-#include <linux/err.h>
-#include <linux/clk.h>
-#include <linux/io.h>
-#include <linux/gpio.h>
-#include <linux/interrupt.h>
-
-#include <linux/regulator/machine.h>
-#include <linux/regulator/fixed.h>
-#include <linux/i2c/twl.h>
-#include <linux/mmc/host.h>
-
-#include <asm/mach-types.h>
-#include <asm/mach/arch.h>
-
-#include <plat/board.h>
-#include <plat/common.h>
-#include <plat/gpmc.h>
-#include <plat/usb.h>
-#include <plat/onenand.h>
-
-#include "mux.h"
-#include "hsmmc.h"
-#include "sdram-numonyx-m65kxxxxam.h"
-
-#define IGEP3_GPIO_LED0_GREEN 54
-#define IGEP3_GPIO_LED0_RED 53
-#define IGEP3_GPIO_LED1_RED 16
-
-#define IGEP3_GPIO_WIFI_NPD 138
-#define IGEP3_GPIO_WIFI_NRESET 139
-#define IGEP3_GPIO_BT_NRESET 137
-
-#define IGEP3_GPIO_USBH_NRESET 183
-
-
-#if defined(CONFIG_MTD_ONENAND_OMAP2) || \
- defined(CONFIG_MTD_ONENAND_OMAP2_MODULE)
-
-#define ONENAND_MAP 0x20000000
-
-/*
- * x2 Flash built-in COMBO POP MEMORY
- * Since the device is equipped with two DataRAMs, and two-plane NAND
- * Flash memory array, these two component enables simultaneous program
- * of 4KiB. Plane1 has only even blocks such as block0, block2, block4
- * while Plane2 has only odd blocks such as block1, block3, block5.
- * So MTD regards it as 4KiB page size and 256KiB block size 64*(2*2048)
- */
-
-static struct mtd_partition igep3_onenand_partitions[] = {
- {
- .name = "X-Loader",
- .offset = 0,
- .size = 2 * (64*(2*2048))
- },
- {
- .name = "U-Boot",
- .offset = MTDPART_OFS_APPEND,
- .size = 6 * (64*(2*2048)),
- },
- {
- .name = "Environment",
- .offset = MTDPART_OFS_APPEND,
- .size = 2 * (64*(2*2048)),
- },
- {
- .name = "Kernel",
- .offset = MTDPART_OFS_APPEND,
- .size = 12 * (64*(2*2048)),
- },
- {
- .name = "File System",
- .offset = MTDPART_OFS_APPEND,
- .size = MTDPART_SIZ_FULL,
- },
-};
-
-static struct omap_onenand_platform_data igep3_onenand_pdata = {
- .parts = igep3_onenand_partitions,
- .nr_parts = ARRAY_SIZE(igep3_onenand_partitions),
- .onenand_setup = NULL,
- .dma_channel = -1, /* disable DMA in OMAP OneNAND driver */
-};
-
-static struct platform_device igep3_onenand_device = {
- .name = "omap2-onenand",
- .id = -1,
- .dev = {
- .platform_data = &igep3_onenand_pdata,
- },
-};
-
-static void __init igep3_flash_init(void)
-{
- u8 cs = 0;
- u8 onenandcs = GPMC_CS_NUM + 1;
-
- for (cs = 0; cs < GPMC_CS_NUM; cs++) {
- u32 ret;
- ret = gpmc_cs_read_reg(cs, GPMC_CS_CONFIG1);
-
- /* Check if NAND/oneNAND is configured */
- if ((ret & 0xC00) == 0x800)
- /* NAND found */
- pr_err("IGEP3: Unsupported NAND found\n");
- else {
- ret = gpmc_cs_read_reg(cs, GPMC_CS_CONFIG7);
-
- if ((ret & 0x3F) == (ONENAND_MAP >> 24))
- /* OneNAND found */
- onenandcs = cs;
- }
- }
-
- if (onenandcs > GPMC_CS_NUM) {
- pr_err("IGEP3: Unable to find configuration in GPMC\n");
- return;
- }
-
- igep3_onenand_pdata.cs = onenandcs;
-
- if (platform_device_register(&igep3_onenand_device) < 0)
- pr_err("IGEP3: Unable to register OneNAND device\n");
-}
-
-#else
-static void __init igep3_flash_init(void) {}
-#endif
-
-static struct regulator_consumer_supply igep3_vmmc1_supply =
- REGULATOR_SUPPLY("vmmc", "omap_hsmmc.0");
-
-/* VMMC1 for OMAP VDD_MMC1 (i/o) and MMC1 card */
-static struct regulator_init_data igep3_vmmc1 = {
- .constraints = {
- .min_uV = 1850000,
- .max_uV = 3150000,
- .valid_modes_mask = REGULATOR_MODE_NORMAL
- | REGULATOR_MODE_STANDBY,
- .valid_ops_mask = REGULATOR_CHANGE_VOLTAGE
- | REGULATOR_CHANGE_MODE
- | REGULATOR_CHANGE_STATUS,
- },
- .num_consumer_supplies = 1,
- .consumer_supplies = &igep3_vmmc1_supply,
-};
-
-static struct regulator_consumer_supply igep3_vio_supply =
- REGULATOR_SUPPLY("vmmc_aux", "omap_hsmmc.1");
-
-static struct regulator_init_data igep3_vio = {
- .constraints = {
- .min_uV = 1800000,
- .max_uV = 1800000,
- .apply_uV = 1,
- .valid_modes_mask = REGULATOR_MODE_NORMAL
- | REGULATOR_MODE_STANDBY,
- .valid_ops_mask = REGULATOR_CHANGE_VOLTAGE
- | REGULATOR_CHANGE_MODE
- | REGULATOR_CHANGE_STATUS,
- },
- .num_consumer_supplies = 1,
- .consumer_supplies = &igep3_vio_supply,
-};
-
-static struct regulator_consumer_supply igep3_vmmc2_supply =
- REGULATOR_SUPPLY("vmmc", "omap_hsmmc.1");
-
-static struct regulator_init_data igep3_vmmc2 = {
- .constraints = {
- .valid_modes_mask = REGULATOR_MODE_NORMAL,
- .always_on = 1,
- },
- .num_consumer_supplies = 1,
- .consumer_supplies = &igep3_vmmc2_supply,
-};
-
-static struct fixed_voltage_config igep3_vwlan = {
- .supply_name = "vwlan",
- .microvolts = 3300000,
- .gpio = -EINVAL,
- .enabled_at_boot = 1,
- .init_data = &igep3_vmmc2,
-};
-
-static struct platform_device igep3_vwlan_device = {
- .name = "reg-fixed-voltage",
- .id = 0,
- .dev = {
- .platform_data = &igep3_vwlan,
- },
-};
-
-static struct omap2_hsmmc_info mmc[] = {
- [0] = {
- .mmc = 1,
- .caps = MMC_CAP_4_BIT_DATA,
- .gpio_cd = -EINVAL,
- .gpio_wp = -EINVAL,
- },
-#if defined(CONFIG_LIBERTAS_SDIO) || defined(CONFIG_LIBERTAS_SDIO_MODULE)
- [1] = {
- .mmc = 2,
- .caps = MMC_CAP_4_BIT_DATA,
- .gpio_cd = -EINVAL,
- .gpio_wp = -EINVAL,
- },
-#endif
- {} /* Terminator */
-};
-
-#if defined(CONFIG_LEDS_GPIO) || defined(CONFIG_LEDS_GPIO_MODULE)
-#include <linux/leds.h>
-
-static struct gpio_led igep3_gpio_leds[] = {
- [0] = {
- .name = "gpio-led:red:d0",
- .gpio = IGEP3_GPIO_LED0_RED,
- .default_trigger = "default-off"
- },
- [1] = {
- .name = "gpio-led:green:d0",
- .gpio = IGEP3_GPIO_LED0_GREEN,
- .default_trigger = "default-off",
- },
- [2] = {
- .name = "gpio-led:red:d1",
- .gpio = IGEP3_GPIO_LED1_RED,
- .default_trigger = "default-off",
- },
- [3] = {
- .name = "gpio-led:green:d1",
- .default_trigger = "heartbeat",
- .gpio = -EINVAL, /* gets replaced */
- },
-};
-
-static struct gpio_led_platform_data igep3_led_pdata = {
- .leds = igep3_gpio_leds,
- .num_leds = ARRAY_SIZE(igep3_gpio_leds),
-};
-
-static struct platform_device igep3_led_device = {
- .name = "leds-gpio",
- .id = -1,
- .dev = {
- .platform_data = &igep3_led_pdata,
- },
-};
-
-static void __init igep3_leds_init(void)
-{
- platform_device_register(&igep3_led_device);
-}
-
-#else
-static inline void igep3_leds_init(void)
-{
- if ((gpio_request(IGEP3_GPIO_LED0_RED, "gpio-led:red:d0") == 0) &&
- (gpio_direction_output(IGEP3_GPIO_LED0_RED, 1) == 0)) {
- gpio_export(IGEP3_GPIO_LED0_RED, 0);
- gpio_set_value(IGEP3_GPIO_LED0_RED, 1);
- } else
- pr_warning("IGEP3: Could not obtain gpio GPIO_LED0_RED\n");
-
- if ((gpio_request(IGEP3_GPIO_LED0_GREEN, "gpio-led:green:d0") == 0) &&
- (gpio_direction_output(IGEP3_GPIO_LED0_GREEN, 1) == 0)) {
- gpio_export(IGEP3_GPIO_LED0_GREEN, 0);
- gpio_set_value(IGEP3_GPIO_LED0_GREEN, 1);
- } else
- pr_warning("IGEP3: Could not obtain gpio GPIO_LED0_GREEN\n");
-
- if ((gpio_request(IGEP3_GPIO_LED1_RED, "gpio-led:red:d1") == 0) &&
- (gpio_direction_output(IGEP3_GPIO_LED1_RED, 1) == 0)) {
- gpio_export(IGEP3_GPIO_LED1_RED, 0);
- gpio_set_value(IGEP3_GPIO_LED1_RED, 1);
- } else
- pr_warning("IGEP3: Could not obtain gpio GPIO_LED1_RED\n");
-}
-#endif
-
-static int igep3_twl4030_gpio_setup(struct device *dev,
- unsigned gpio, unsigned ngpio)
-{
- /* gpio + 0 is "mmc0_cd" (input/IRQ) */
- mmc[0].gpio_cd = gpio + 0;
- omap2_hsmmc_init(mmc);
-
- /* TWL4030_GPIO_MAX + 1 == ledB (out, active low LED) */
-#if !defined(CONFIG_LEDS_GPIO) && !defined(CONFIG_LEDS_GPIO_MODULE)
- if ((gpio_request(gpio+TWL4030_GPIO_MAX+1, "gpio-led:green:d1") == 0)
- && (gpio_direction_output(gpio + TWL4030_GPIO_MAX + 1, 1) == 0)) {
- gpio_export(gpio + TWL4030_GPIO_MAX + 1, 0);
- gpio_set_value(gpio + TWL4030_GPIO_MAX + 1, 0);
- } else
- pr_warning("IGEP3: Could not obtain gpio GPIO_LED1_GREEN\n");
-#else
- igep3_gpio_leds[3].gpio = gpio + TWL4030_GPIO_MAX + 1;
-#endif
-
- return 0;
-};
-
-static struct twl4030_gpio_platform_data igep3_twl4030_gpio_pdata = {
- .gpio_base = OMAP_MAX_GPIO_LINES,
- .irq_base = TWL4030_GPIO_IRQ_BASE,
- .irq_end = TWL4030_GPIO_IRQ_END,
- .use_leds = true,
- .setup = igep3_twl4030_gpio_setup,
-};
-
-static struct twl4030_usb_data igep3_twl4030_usb_data = {
- .usb_mode = T2_USB_MODE_ULPI,
-};
-
-static struct platform_device *igep3_devices[] __initdata = {
- &igep3_vwlan_device,
-};
-
-static void __init igep3_init_early(void)
-{
- omap2_init_common_infrastructure();
- omap2_init_common_devices(m65kxxxxam_sdrc_params,
- m65kxxxxam_sdrc_params);
-}
-
-static struct twl4030_platform_data igep3_twl4030_pdata = {
- .irq_base = TWL4030_IRQ_BASE,
- .irq_end = TWL4030_IRQ_END,
-
- /* platform_data for children goes here */
- .usb = &igep3_twl4030_usb_data,
- .gpio = &igep3_twl4030_gpio_pdata,
- .vmmc1 = &igep3_vmmc1,
- .vio = &igep3_vio,
-};
-
-static struct i2c_board_info __initdata igep3_i2c_boardinfo[] = {
- {
- I2C_BOARD_INFO("twl4030", 0x48),
- .flags = I2C_CLIENT_WAKE,
- .irq = INT_34XX_SYS_NIRQ,
- .platform_data = &igep3_twl4030_pdata,
- },
-};
-
-static int __init igep3_i2c_init(void)
-{
- omap_register_i2c_bus(1, 2600, igep3_i2c_boardinfo,
- ARRAY_SIZE(igep3_i2c_boardinfo));
-
- return 0;
-}
-
-static struct omap_musb_board_data musb_board_data = {
- .interface_type = MUSB_INTERFACE_ULPI,
- .mode = MUSB_OTG,
- .power = 100,
-};
-
-#if defined(CONFIG_LIBERTAS_SDIO) || defined(CONFIG_LIBERTAS_SDIO_MODULE)
-
-static void __init igep3_wifi_bt_init(void)
-{
- /* Configure MUX values for W-LAN + Bluetooth GPIO's */
- omap_mux_init_gpio(IGEP3_GPIO_WIFI_NPD, OMAP_PIN_OUTPUT);
- omap_mux_init_gpio(IGEP3_GPIO_WIFI_NRESET, OMAP_PIN_OUTPUT);
- omap_mux_init_gpio(IGEP3_GPIO_BT_NRESET, OMAP_PIN_OUTPUT);
-
- /* Set GPIO's for W-LAN + Bluetooth combo module */
- if ((gpio_request(IGEP3_GPIO_WIFI_NPD, "GPIO_WIFI_NPD") == 0) &&
- (gpio_direction_output(IGEP3_GPIO_WIFI_NPD, 1) == 0)) {
- gpio_export(IGEP3_GPIO_WIFI_NPD, 0);
- } else
- pr_warning("IGEP3: Could not obtain gpio GPIO_WIFI_NPD\n");
-
- if ((gpio_request(IGEP3_GPIO_WIFI_NRESET, "GPIO_WIFI_NRESET") == 0) &&
- (gpio_direction_output(IGEP3_GPIO_WIFI_NRESET, 1) == 0)) {
- gpio_export(IGEP3_GPIO_WIFI_NRESET, 0);
- gpio_set_value(IGEP3_GPIO_WIFI_NRESET, 0);
- udelay(10);
- gpio_set_value(IGEP3_GPIO_WIFI_NRESET, 1);
- } else
- pr_warning("IGEP3: Could not obtain gpio GPIO_WIFI_NRESET\n");
-
- if ((gpio_request(IGEP3_GPIO_BT_NRESET, "GPIO_BT_NRESET") == 0) &&
- (gpio_direction_output(IGEP3_GPIO_BT_NRESET, 1) == 0)) {
- gpio_export(IGEP3_GPIO_BT_NRESET, 0);
- } else
- pr_warning("IGEP3: Could not obtain gpio GPIO_BT_NRESET\n");
-}
-#else
-void __init igep3_wifi_bt_init(void) {}
-#endif
-
-static const struct usbhs_omap_board_data usbhs_bdata __initconst = {
- .port_mode[0] = OMAP_USBHS_PORT_MODE_UNUSED,
- .port_mode[1] = OMAP_EHCI_PORT_MODE_PHY,
- .port_mode[2] = OMAP_USBHS_PORT_MODE_UNUSED,
-
- .phy_reset = true,
- .reset_gpio_port[0] = -EINVAL,
- .reset_gpio_port[1] = IGEP3_GPIO_USBH_NRESET,
- .reset_gpio_port[2] = -EINVAL,
-};
-
-#ifdef CONFIG_OMAP_MUX
-static struct omap_board_mux board_mux[] __initdata = {
- OMAP3_MUX(I2C2_SDA, OMAP_MUX_MODE4 | OMAP_PIN_OUTPUT),
- { .reg_offset = OMAP_MUX_TERMINATOR },
-};
-#endif
-
-static void __init igep3_init(void)
-{
- omap3_mux_init(board_mux, OMAP_PACKAGE_CBB);
-
- /* Register I2C busses and drivers */
- igep3_i2c_init();
- platform_add_devices(igep3_devices, ARRAY_SIZE(igep3_devices));
- omap_serial_init();
- usb_musb_init(&musb_board_data);
- usbhs_init(&usbhs_bdata);
-
- igep3_flash_init();
- igep3_leds_init();
-
- /*
- * WLAN-BT combo module from MuRata which has a Marvell WLAN
- * (88W8686) + CSR Bluetooth chipset. Uses SDIO interface.
- */
- igep3_wifi_bt_init();
-
-}
-
-MACHINE_START(IGEP0030, "IGEP OMAP3 module")
- .boot_params = 0x80000100,
- .reserve = omap_reserve,
- .map_io = omap3_map_io,
- .init_early = igep3_init_early,
- .init_irq = omap_init_irq,
- .init_machine = igep3_init,
- .timer = &omap_timer,
-MACHINE_END
#include <linux/err.h>
#include <linux/clk.h>
#include <linux/spi/spi.h>
-#include <linux/spi/ads7846.h>
#include <linux/regulator/machine.h>
#include <linux/i2c/twl.h>
#include <linux/io.h>
#include <asm/delay.h>
#include <plat/usb.h>
+#include <plat/gpmc-smsc911x.h>
#include "board-flash.h"
#include "mux.h"
#include "hsmmc.h"
#include "control.h"
+#include "common-board-devices.h"
#define LDP_SMSC911X_CS 1
#define LDP_SMSC911X_GPIO 152
#define DEBUG_BASE 0x08000000
#define LDP_ETHR_START DEBUG_BASE
-static struct resource ldp_smsc911x_resources[] = {
- [0] = {
- .start = LDP_ETHR_START,
- .end = LDP_ETHR_START + SZ_4K,
- .flags = IORESOURCE_MEM,
- },
- [1] = {
- .start = 0,
- .end = 0,
- .flags = IORESOURCE_IRQ | IORESOURCE_IRQ_LOWLEVEL,
- },
-};
-
-static struct smsc911x_platform_config ldp_smsc911x_config = {
- .irq_polarity = SMSC911X_IRQ_POLARITY_ACTIVE_LOW,
- .irq_type = SMSC911X_IRQ_TYPE_OPEN_DRAIN,
- .flags = SMSC911X_USE_32BIT,
- .phy_interface = PHY_INTERFACE_MODE_MII,
-};
-
-static struct platform_device ldp_smsc911x_device = {
- .name = "smsc911x",
- .id = -1,
- .num_resources = ARRAY_SIZE(ldp_smsc911x_resources),
- .resource = ldp_smsc911x_resources,
- .dev = {
- .platform_data = &ldp_smsc911x_config,
- },
-};
-
static uint32_t board_keymap[] = {
KEY(0, 0, KEY_1),
KEY(1, 0, KEY_2),
},
};
-static int ts_gpio;
-
-/**
- * @brief ads7846_dev_init : Requests & sets GPIO line for pen-irq
- *
- * @return - void. If request gpio fails then Flag KERN_ERR.
- */
-static void ads7846_dev_init(void)
-{
- if (gpio_request(ts_gpio, "ads7846 irq") < 0) {
- printk(KERN_ERR "can't get ads746 pen down GPIO\n");
- return;
- }
-
- gpio_direction_input(ts_gpio);
- gpio_set_debounce(ts_gpio, 310);
-}
-
-static int ads7846_get_pendown_state(void)
-{
- return !gpio_get_value(ts_gpio);
-}
-
-static struct ads7846_platform_data tsc2046_config __initdata = {
- .get_pendown_state = ads7846_get_pendown_state,
- .keep_vref_on = 1,
-};
-
-static struct omap2_mcspi_device_config tsc2046_mcspi_config = {
- .turbo_mode = 0,
- .single_channel = 1, /* 0: slave, 1: master */
-};
-
-static struct spi_board_info ldp_spi_board_info[] __initdata = {
- [0] = {
- /*
- * TSC2046 operates at a max freqency of 2MHz, so
- * operate slightly below at 1.5MHz
- */
- .modalias = "ads7846",
- .bus_num = 1,
- .chip_select = 0,
- .max_speed_hz = 1500000,
- .controller_data = &tsc2046_mcspi_config,
- .irq = 0,
- .platform_data = &tsc2046_config,
- },
+static struct omap_smsc911x_platform_data smsc911x_cfg = {
+ .cs = LDP_SMSC911X_CS,
+ .gpio_irq = LDP_SMSC911X_GPIO,
+ .gpio_reset = -EINVAL,
+ .flags = SMSC911X_USE_32BIT,
};
static inline void __init ldp_init_smsc911x(void)
{
- int eth_cs;
- unsigned long cs_mem_base;
- int eth_gpio = 0;
-
- eth_cs = LDP_SMSC911X_CS;
-
- if (gpmc_cs_request(eth_cs, SZ_16M, &cs_mem_base) < 0) {
- printk(KERN_ERR "Failed to request GPMC mem for smsc911x\n");
- return;
- }
-
- ldp_smsc911x_resources[0].start = cs_mem_base + 0x0;
- ldp_smsc911x_resources[0].end = cs_mem_base + 0xff;
- udelay(100);
-
- eth_gpio = LDP_SMSC911X_GPIO;
-
- ldp_smsc911x_resources[1].start = OMAP_GPIO_IRQ(eth_gpio);
-
- if (gpio_request(eth_gpio, "smsc911x irq") < 0) {
- printk(KERN_ERR "Failed to request GPIO%d for smsc911x IRQ\n",
- eth_gpio);
- return;
- }
- gpio_direction_input(eth_gpio);
+ gpmc_smsc911x_init(&smsc911x_cfg);
}
static struct platform_device ldp_lcd_device = {
.keypad = &ldp_kp_twl4030_data,
};
-static struct i2c_board_info __initdata ldp_i2c_boardinfo[] = {
- {
- I2C_BOARD_INFO("twl4030", 0x48),
- .flags = I2C_CLIENT_WAKE,
- .irq = INT_34XX_SYS_NIRQ,
- .platform_data = &ldp_twldata,
- },
-};
-
static int __init omap_i2c_init(void)
{
- omap_register_i2c_bus(1, 2600, ldp_i2c_boardinfo,
- ARRAY_SIZE(ldp_i2c_boardinfo));
+ omap3_pmic_init("twl4030", &ldp_twldata);
omap_register_i2c_bus(2, 400, NULL, 0);
omap_register_i2c_bus(3, 400, NULL, 0);
return 0;
};
static struct platform_device *ldp_devices[] __initdata = {
- &ldp_smsc911x_device,
&ldp_lcd_device,
&ldp_gpio_keys_device,
};
};
#endif
-static struct omap_musb_board_data musb_board_data = {
- .interface_type = MUSB_INTERFACE_ULPI,
- .mode = MUSB_OTG,
- .power = 100,
-};
-
static struct mtd_partition ldp_nand_partitions[] = {
/* All the partition sizes are listed in terms of NAND block size */
{
ldp_init_smsc911x();
omap_i2c_init();
platform_add_devices(ldp_devices, ARRAY_SIZE(ldp_devices));
- ts_gpio = 54;
- ldp_spi_board_info[0].irq = gpio_to_irq(ts_gpio);
- spi_register_board_info(ldp_spi_board_info,
- ARRAY_SIZE(ldp_spi_board_info));
- ads7846_dev_init();
+ omap_ads7846_init(1, 54, 310, NULL);
omap_serial_init();
- usb_musb_init(&musb_board_data);
+ usb_musb_init(NULL);
board_nand_init(ldp_nand_partitions,
ARRAY_SIZE(ldp_nand_partitions), ZOOM_NAND_CS, 0);
static char announce[] __initdata = KERN_INFO "TUSB 6010\n";
/* PM companion chip power control pin */
- ret = gpio_request(TUSB6010_GPIO_ENABLE, "TUSB6010 enable");
+ ret = gpio_request_one(TUSB6010_GPIO_ENABLE, GPIOF_OUT_INIT_LOW,
+ "TUSB6010 enable");
if (ret != 0) {
printk(KERN_ERR "Could not get TUSB power GPIO%i\n",
TUSB6010_GPIO_ENABLE);
return;
}
- gpio_direction_output(TUSB6010_GPIO_ENABLE, 0);
-
tusb_set_power(0);
ret = tusb6010_setup_interface(&tusb_data, TUSB6010_REFCLK_19, 2,
static struct omap_mmc_platform_data *mmc_data[OMAP24XX_NR_MMC];
-static void __init n8x0_mmc_init(void)
+static struct gpio n810_emmc_gpios[] __initdata = {
+ { N810_EMMC_VSD_GPIO, GPIOF_OUT_INIT_LOW, "MMC slot 2 Vddf" },
+ { N810_EMMC_VIO_GPIO, GPIOF_OUT_INIT_LOW, "MMC slot 2 Vdd" },
+};
+static void __init n8x0_mmc_init(void)
{
int err;
mmc1_data.slots[1].ban_openended = 1;
}
- err = gpio_request(N8X0_SLOT_SWITCH_GPIO, "MMC slot switch");
+ err = gpio_request_one(N8X0_SLOT_SWITCH_GPIO, GPIOF_OUT_INIT_LOW,
+ "MMC slot switch");
if (err)
return;
- gpio_direction_output(N8X0_SLOT_SWITCH_GPIO, 0);
-
if (machine_is_nokia_n810()) {
- err = gpio_request(N810_EMMC_VSD_GPIO, "MMC slot 2 Vddf");
- if (err) {
- gpio_free(N8X0_SLOT_SWITCH_GPIO);
- return;
- }
- gpio_direction_output(N810_EMMC_VSD_GPIO, 0);
-
- err = gpio_request(N810_EMMC_VIO_GPIO, "MMC slot 2 Vdd");
+ err = gpio_request_array(n810_emmc_gpios,
+ ARRAY_SIZE(n810_emmc_gpios));
if (err) {
gpio_free(N8X0_SLOT_SWITCH_GPIO);
- gpio_free(N810_EMMC_VSD_GPIO);
return;
}
- gpio_direction_output(N810_EMMC_VIO_GPIO, 0);
}
mmc_data[0] = &mmc1_data;
#include "hsmmc.h"
#include "timer-gp.h"
#include "pm.h"
+#include "common-board-devices.h"
#define NAND_BLOCK_SIZE SZ_128K
return omap3_beagle_version;
}
+static struct gpio omap3_beagle_rev_gpios[] __initdata = {
+ { 171, GPIOF_IN, "rev_id_0" },
+ { 172, GPIOF_IN, "rev_id_1" },
+ { 173, GPIOF_IN, "rev_id_2" },
+};
+
static void __init omap3_beagle_init_rev(void)
{
int ret;
omap_mux_init_gpio(172, OMAP_PIN_INPUT_PULLUP);
omap_mux_init_gpio(173, OMAP_PIN_INPUT_PULLUP);
- ret = gpio_request(171, "rev_id_0");
- if (ret < 0)
- goto fail0;
-
- ret = gpio_request(172, "rev_id_1");
- if (ret < 0)
- goto fail1;
-
- ret = gpio_request(173, "rev_id_2");
- if (ret < 0)
- goto fail2;
-
- gpio_direction_input(171);
- gpio_direction_input(172);
- gpio_direction_input(173);
+ ret = gpio_request_array(omap3_beagle_rev_gpios,
+ ARRAY_SIZE(omap3_beagle_rev_gpios));
+ if (ret < 0) {
+ printk(KERN_ERR "Unable to get revision detection GPIO pins\n");
+ omap3_beagle_version = OMAP3BEAGLE_BOARD_UNKN;
+ return;
+ }
beagle_rev = gpio_get_value(171) | (gpio_get_value(172) << 1)
| (gpio_get_value(173) << 2);
printk(KERN_INFO "OMAP3 Beagle Rev: unknown %hd\n", beagle_rev);
omap3_beagle_version = OMAP3BEAGLE_BOARD_UNKN;
}
-
- return;
-
-fail2:
- gpio_free(172);
-fail1:
- gpio_free(171);
-fail0:
- printk(KERN_ERR "Unable to get revision detection GPIO pins\n");
- omap3_beagle_version = OMAP3BEAGLE_BOARD_UNKN;
-
- return;
}
static struct mtd_partition omap3beagle_nand_partitions[] = {
},
};
-static struct omap_nand_platform_data omap3beagle_nand_data = {
- .options = NAND_BUSWIDTH_16,
- .parts = omap3beagle_nand_partitions,
- .nr_parts = ARRAY_SIZE(omap3beagle_nand_partitions),
- .dma_channel = -1, /* disable DMA in OMAP NAND driver */
- .nand_setup = NULL,
- .dev_ready = NULL,
-};
-
/* DSS */
static int beagle_enable_dvi(struct omap_dss_device *dssdev)
{
int r;
- r = gpio_request(beagle_dvi_device.reset_gpio, "DVI reset");
- if (r < 0) {
+ r = gpio_request_one(beagle_dvi_device.reset_gpio, GPIOF_OUT_INIT_LOW,
+ "DVI reset");
+ if (r < 0)
printk(KERN_ERR "Unable to get DVI reset GPIO\n");
- return;
- }
-
- gpio_direction_output(beagle_dvi_device.reset_gpio, 0);
}
#include "sdram-micron-mt46h32m32lf-6.h"
static int beagle_twl_gpio_setup(struct device *dev,
unsigned gpio, unsigned ngpio)
{
- int r;
+ int r, usb_pwr_level;
if (omap3_beagle_get_rev() == OMAP3BEAGLE_BOARD_XM) {
mmc[0].gpio_wp = -EINVAL;
beagle_vmmc1_supply.dev = mmc[0].dev;
beagle_vsim_supply.dev = mmc[0].dev;
- /* REVISIT: need ehci-omap hooks for external VBUS
- * power switch and overcurrent detect
- */
- if (omap3_beagle_get_rev() != OMAP3BEAGLE_BOARD_XM) {
- r = gpio_request(gpio + 1, "EHCI_nOC");
- if (!r) {
- r = gpio_direction_input(gpio + 1);
- if (r)
- gpio_free(gpio + 1);
- }
- if (r)
- pr_err("%s: unable to configure EHCI_nOC\n", __func__);
- }
-
/*
* TWL4030_GPIO_MAX + 0 == ledA, EHCI nEN_USB_PWR (out, XM active
* high / others active low)
- */
- gpio_request(gpio + TWL4030_GPIO_MAX, "nEN_USB_PWR");
- if (omap3_beagle_get_rev() == OMAP3BEAGLE_BOARD_XM)
- gpio_direction_output(gpio + TWL4030_GPIO_MAX, 1);
- else
- gpio_direction_output(gpio + TWL4030_GPIO_MAX, 0);
-
- /* DVI reset GPIO is different between beagle revisions */
- if (omap3_beagle_get_rev() == OMAP3BEAGLE_BOARD_XM)
- beagle_dvi_device.reset_gpio = 129;
- else
- beagle_dvi_device.reset_gpio = 170;
-
- /* TWL4030_GPIO_MAX + 1 == ledB, PMU_STAT (out, active low LED) */
- gpio_leds[2].gpio = gpio + TWL4030_GPIO_MAX + 1;
-
- /*
- * gpio + 1 on Xm controls the TFP410's enable line (active low)
- * gpio + 2 control varies depending on the board rev as follows:
- * P7/P8 revisions(prototype): Camera EN
- * A2+ revisions (production): LDO (supplies DVI, serial, led blocks)
+ * DVI reset GPIO is different between beagle revisions
*/
if (omap3_beagle_get_rev() == OMAP3BEAGLE_BOARD_XM) {
- r = gpio_request(gpio + 1, "nDVI_PWR_EN");
- if (!r) {
- r = gpio_direction_output(gpio + 1, 0);
- if (r)
- gpio_free(gpio + 1);
- }
+ usb_pwr_level = GPIOF_OUT_INIT_HIGH;
+ beagle_dvi_device.reset_gpio = 129;
+ /*
+ * gpio + 1 on Xm controls the TFP410's enable line (active low)
+ * gpio + 2 control varies depending on the board rev as below:
+ * P7/P8 revisions(prototype): Camera EN
+ * A2+ revisions (production): LDO (DVI, serial, led blocks)
+ */
+ r = gpio_request_one(gpio + 1, GPIOF_OUT_INIT_LOW,
+ "nDVI_PWR_EN");
if (r)
pr_err("%s: unable to configure nDVI_PWR_EN\n",
__func__);
- r = gpio_request(gpio + 2, "DVI_LDO_EN");
- if (!r) {
- r = gpio_direction_output(gpio + 2, 1);
- if (r)
- gpio_free(gpio + 2);
- }
+ r = gpio_request_one(gpio + 2, GPIOF_OUT_INIT_HIGH,
+ "DVI_LDO_EN");
if (r)
pr_err("%s: unable to configure DVI_LDO_EN\n",
__func__);
+ } else {
+ usb_pwr_level = GPIOF_OUT_INIT_LOW;
+ beagle_dvi_device.reset_gpio = 170;
+ /*
+ * REVISIT: need ehci-omap hooks for external VBUS
+ * power switch and overcurrent detect
+ */
+ if (gpio_request_one(gpio + 1, GPIOF_IN, "EHCI_nOC"))
+ pr_err("%s: unable to configure EHCI_nOC\n", __func__);
}
+ gpio_request_one(gpio + TWL4030_GPIO_MAX, usb_pwr_level, "nEN_USB_PWR");
+
+ /* TWL4030_GPIO_MAX + 1 == ledB, PMU_STAT (out, active low LED) */
+ gpio_leds[2].gpio = gpio + TWL4030_GPIO_MAX + 1;
+
return 0;
}
.vpll2 = &beagle_vpll2,
};
-static struct i2c_board_info __initdata beagle_i2c_boardinfo[] = {
- {
- I2C_BOARD_INFO("twl4030", 0x48),
- .flags = I2C_CLIENT_WAKE,
- .irq = INT_34XX_SYS_NIRQ,
- .platform_data = &beagle_twldata,
- },
-};
-
static struct i2c_board_info __initdata beagle_i2c_eeprom[] = {
{
I2C_BOARD_INFO("eeprom", 0x50),
static int __init omap3_beagle_i2c_init(void)
{
- omap_register_i2c_bus(1, 2600, beagle_i2c_boardinfo,
- ARRAY_SIZE(beagle_i2c_boardinfo));
+ omap3_pmic_init("twl4030", &beagle_twldata);
/* Bus 3 is attached to the DVI port where devices like the pico DLP
* projector don't work reliably with 400kHz */
omap_register_i2c_bus(3, 100, beagle_i2c_eeprom, ARRAY_SIZE(beagle_i2c_eeprom));
&keys_gpio,
};
-static void __init omap3beagle_flash_init(void)
-{
- u8 cs = 0;
- u8 nandcs = GPMC_CS_NUM + 1;
-
- /* find out the chip-select on which NAND exists */
- while (cs < GPMC_CS_NUM) {
- u32 ret = 0;
- ret = gpmc_cs_read_reg(cs, GPMC_CS_CONFIG1);
-
- if ((ret & 0xC00) == 0x800) {
- printk(KERN_INFO "Found NAND on CS%d\n", cs);
- if (nandcs > GPMC_CS_NUM)
- nandcs = cs;
- }
- cs++;
- }
-
- if (nandcs > GPMC_CS_NUM) {
- printk(KERN_INFO "NAND: Unable to find configuration "
- "in GPMC\n ");
- return;
- }
-
- if (nandcs < GPMC_CS_NUM) {
- omap3beagle_nand_data.cs = nandcs;
-
- printk(KERN_INFO "Registering NAND on CS%d\n", nandcs);
- if (gpmc_nand_init(&omap3beagle_nand_data) < 0)
- printk(KERN_ERR "Unable to register NAND device\n");
- }
-}
-
static const struct usbhs_omap_board_data usbhs_bdata __initconst = {
.port_mode[0] = OMAP_EHCI_PORT_MODE_PHY,
};
#endif
-static struct omap_musb_board_data musb_board_data = {
- .interface_type = MUSB_INTERFACE_ULPI,
- .mode = MUSB_OTG,
- .power = 100,
-};
-
static void __init beagle_opp_init(void)
{
int r = 0;
omap_serial_init();
omap_mux_init_gpio(170, OMAP_PIN_INPUT);
- gpio_request(170, "DVI_nPD");
/* REVISIT leave DVI powered down until it's needed ... */
- gpio_direction_output(170, true);
+ gpio_request_one(170, GPIOF_OUT_INIT_HIGH, "DVI_nPD");
- usb_musb_init(&musb_board_data);
+ usb_musb_init(NULL);
usbhs_init(&usbhs_bdata);
- omap3beagle_flash_init();
+ omap_nand_flash_init(NAND_BUSWIDTH_16, omap3beagle_nand_partitions,
+ ARRAY_SIZE(omap3beagle_nand_partitions));
/* Ensure SDRC pins are mux'd for self-refresh */
omap_mux_init_signal("sdrc_cke0", OMAP_PIN_OUTPUT);
#include "mux.h"
#include "sdram-micron-mt46h32m32lf-6.h"
#include "hsmmc.h"
+#include "common-board-devices.h"
#define OMAP3_EVM_TS_GPIO 175
#define OMAP3_EVM_EHCI_VBUS 22
}
#if defined(CONFIG_SMSC911X) || defined(CONFIG_SMSC911X_MODULE)
-static struct resource omap3evm_smsc911x_resources[] = {
- [0] = {
- .start = OMAP3EVM_ETHR_START,
- .end = (OMAP3EVM_ETHR_START + OMAP3EVM_ETHR_SIZE - 1),
- .flags = IORESOURCE_MEM,
- },
- [1] = {
- .start = OMAP_GPIO_IRQ(OMAP3EVM_ETHR_GPIO_IRQ),
- .end = OMAP_GPIO_IRQ(OMAP3EVM_ETHR_GPIO_IRQ),
- .flags = (IORESOURCE_IRQ | IRQF_TRIGGER_LOW),
- },
-};
+#include <plat/gpmc-smsc911x.h>
-static struct smsc911x_platform_config smsc911x_config = {
- .phy_interface = PHY_INTERFACE_MODE_MII,
- .irq_polarity = SMSC911X_IRQ_POLARITY_ACTIVE_LOW,
- .irq_type = SMSC911X_IRQ_TYPE_OPEN_DRAIN,
- .flags = (SMSC911X_USE_32BIT | SMSC911X_SAVE_MAC_ADDRESS),
-};
-
-static struct platform_device omap3evm_smsc911x_device = {
- .name = "smsc911x",
- .id = -1,
- .num_resources = ARRAY_SIZE(omap3evm_smsc911x_resources),
- .resource = &omap3evm_smsc911x_resources[0],
- .dev = {
- .platform_data = &smsc911x_config,
- },
+static struct omap_smsc911x_platform_data smsc911x_cfg = {
+ .cs = OMAP3EVM_SMSC911X_CS,
+ .gpio_irq = OMAP3EVM_ETHR_GPIO_IRQ,
+ .gpio_reset = -EINVAL,
+ .flags = SMSC911X_USE_32BIT | SMSC911X_SAVE_MAC_ADDRESS,
};
static inline void __init omap3evm_init_smsc911x(void)
{
- int eth_cs, eth_rst;
struct clk *l3ck;
unsigned int rate;
- if (get_omap3_evm_rev() == OMAP3EVM_BOARD_GEN_1)
- eth_rst = OMAP3EVM_GEN1_ETHR_GPIO_RST;
- else
- eth_rst = OMAP3EVM_GEN2_ETHR_GPIO_RST;
-
- eth_cs = OMAP3EVM_SMSC911X_CS;
-
l3ck = clk_get(NULL, "l3_ck");
if (IS_ERR(l3ck))
rate = 100000000;
/* Configure ethernet controller reset gpio */
if (cpu_is_omap3430()) {
- if (gpio_request(eth_rst, "SMSC911x gpio") < 0) {
- pr_err(KERN_ERR "Failed to request %d for smsc911x\n",
- eth_rst);
- return;
- }
-
- if (gpio_direction_output(eth_rst, 1) < 0) {
- pr_err(KERN_ERR "Failed to set direction of %d for" \
- " smsc911x\n", eth_rst);
- return;
- }
- /* reset pulse to ethernet controller*/
- usleep_range(150, 220);
- gpio_set_value(eth_rst, 0);
- usleep_range(150, 220);
- gpio_set_value(eth_rst, 1);
- usleep_range(1, 2);
- }
-
- if (gpio_request(OMAP3EVM_ETHR_GPIO_IRQ, "SMSC911x irq") < 0) {
- printk(KERN_ERR "Failed to request GPIO%d for smsc911x IRQ\n",
- OMAP3EVM_ETHR_GPIO_IRQ);
- return;
+ if (get_omap3_evm_rev() == OMAP3EVM_BOARD_GEN_1)
+ smsc911x_cfg.gpio_reset = OMAP3EVM_GEN1_ETHR_GPIO_RST;
+ else
+ smsc911x_cfg.gpio_reset = OMAP3EVM_GEN2_ETHR_GPIO_RST;
}
- gpio_direction_input(OMAP3EVM_ETHR_GPIO_IRQ);
- platform_device_register(&omap3evm_smsc911x_device);
+ gpmc_smsc911x_init(&smsc911x_cfg);
}
#else
#define OMAP3EVM_LCD_PANEL_BKLIGHT_GPIO 210
#define OMAP3EVM_DVI_PANEL_EN_GPIO 199
+static struct gpio omap3_evm_dss_gpios[] __initdata = {
+ { OMAP3EVM_LCD_PANEL_RESB, GPIOF_OUT_INIT_HIGH, "lcd_panel_resb" },
+ { OMAP3EVM_LCD_PANEL_INI, GPIOF_OUT_INIT_HIGH, "lcd_panel_ini" },
+ { OMAP3EVM_LCD_PANEL_QVGA, GPIOF_OUT_INIT_LOW, "lcd_panel_qvga" },
+ { OMAP3EVM_LCD_PANEL_LR, GPIOF_OUT_INIT_HIGH, "lcd_panel_lr" },
+ { OMAP3EVM_LCD_PANEL_UD, GPIOF_OUT_INIT_HIGH, "lcd_panel_ud" },
+ { OMAP3EVM_LCD_PANEL_ENVDD, GPIOF_OUT_INIT_LOW, "lcd_panel_envdd" },
+};
+
static int lcd_enabled;
static int dvi_enabled;
{
int r;
- r = gpio_request(OMAP3EVM_LCD_PANEL_RESB, "lcd_panel_resb");
- if (r) {
- printk(KERN_ERR "failed to get lcd_panel_resb\n");
- return;
- }
- gpio_direction_output(OMAP3EVM_LCD_PANEL_RESB, 1);
-
- r = gpio_request(OMAP3EVM_LCD_PANEL_INI, "lcd_panel_ini");
- if (r) {
- printk(KERN_ERR "failed to get lcd_panel_ini\n");
- goto err_1;
- }
- gpio_direction_output(OMAP3EVM_LCD_PANEL_INI, 1);
-
- r = gpio_request(OMAP3EVM_LCD_PANEL_QVGA, "lcd_panel_qvga");
- if (r) {
- printk(KERN_ERR "failed to get lcd_panel_qvga\n");
- goto err_2;
- }
- gpio_direction_output(OMAP3EVM_LCD_PANEL_QVGA, 0);
-
- r = gpio_request(OMAP3EVM_LCD_PANEL_LR, "lcd_panel_lr");
- if (r) {
- printk(KERN_ERR "failed to get lcd_panel_lr\n");
- goto err_3;
- }
- gpio_direction_output(OMAP3EVM_LCD_PANEL_LR, 1);
-
- r = gpio_request(OMAP3EVM_LCD_PANEL_UD, "lcd_panel_ud");
- if (r) {
- printk(KERN_ERR "failed to get lcd_panel_ud\n");
- goto err_4;
- }
- gpio_direction_output(OMAP3EVM_LCD_PANEL_UD, 1);
-
- r = gpio_request(OMAP3EVM_LCD_PANEL_ENVDD, "lcd_panel_envdd");
- if (r) {
- printk(KERN_ERR "failed to get lcd_panel_envdd\n");
- goto err_5;
- }
- gpio_direction_output(OMAP3EVM_LCD_PANEL_ENVDD, 0);
-
- return;
-
-err_5:
- gpio_free(OMAP3EVM_LCD_PANEL_UD);
-err_4:
- gpio_free(OMAP3EVM_LCD_PANEL_LR);
-err_3:
- gpio_free(OMAP3EVM_LCD_PANEL_QVGA);
-err_2:
- gpio_free(OMAP3EVM_LCD_PANEL_INI);
-err_1:
- gpio_free(OMAP3EVM_LCD_PANEL_RESB);
-
+ r = gpio_request_array(omap3_evm_dss_gpios,
+ ARRAY_SIZE(omap3_evm_dss_gpios));
+ if (r)
+ printk(KERN_ERR "failed to get lcd_panel_* gpios\n");
}
static int omap3_evm_enable_lcd(struct omap_dss_device *dssdev)
static int omap3evm_twl_gpio_setup(struct device *dev,
unsigned gpio, unsigned ngpio)
{
- int r;
+ int r, lcd_bl_en;
/* gpio + 0 is "mmc0_cd" (input/IRQ) */
omap_mux_init_gpio(63, OMAP_PIN_INPUT);
*/
/* TWL4030_GPIO_MAX + 0 == ledA, LCD Backlight control */
- r = gpio_request(gpio + TWL4030_GPIO_MAX, "EN_LCD_BKL");
- if (!r)
- r = gpio_direction_output(gpio + TWL4030_GPIO_MAX,
- (get_omap3_evm_rev() >= OMAP3EVM_BOARD_GEN_2) ? 1 : 0);
+ lcd_bl_en = get_omap3_evm_rev() >= OMAP3EVM_BOARD_GEN_2 ?
+ GPIOF_OUT_INIT_HIGH : GPIOF_OUT_INIT_LOW;
+ r = gpio_request_one(gpio + TWL4030_GPIO_MAX, lcd_bl_en, "EN_LCD_BKL");
if (r)
printk(KERN_ERR "failed to get/set lcd_bkl gpio\n");
/* gpio + 7 == DVI Enable */
- gpio_request(gpio + 7, "EN_DVI");
- gpio_direction_output(gpio + 7, 0);
+ gpio_request_one(gpio + 7, GPIOF_OUT_INIT_LOW, "EN_DVI");
/* TWL4030_GPIO_MAX + 1 == ledB (out, active low LED) */
gpio_leds[2].gpio = gpio + TWL4030_GPIO_MAX + 1;
.vdac = &omap3_evm_vdac,
.vpll2 = &omap3_evm_vpll2,
.vio = &omap3evm_vio,
-};
-
-static struct i2c_board_info __initdata omap3evm_i2c_boardinfo[] = {
- {
- I2C_BOARD_INFO("twl4030", 0x48),
- .flags = I2C_CLIENT_WAKE,
- .irq = INT_34XX_SYS_NIRQ,
- .platform_data = &omap3evm_twldata,
- },
+ .vmmc1 = &omap3evm_vmmc1,
+ .vsim = &omap3evm_vsim,
};
static int __init omap3_evm_i2c_init(void)
{
- /*
- * REVISIT: These entries can be set in omap3evm_twl_data
- * after a merge with MFD tree
- */
- omap3evm_twldata.vmmc1 = &omap3evm_vmmc1;
- omap3evm_twldata.vsim = &omap3evm_vsim;
-
- omap_register_i2c_bus(1, 2600, omap3evm_i2c_boardinfo,
- ARRAY_SIZE(omap3evm_i2c_boardinfo));
+ omap3_pmic_init("twl4030", &omap3evm_twldata);
omap_register_i2c_bus(2, 400, NULL, 0);
omap_register_i2c_bus(3, 400, NULL, 0);
return 0;
}
-static void ads7846_dev_init(void)
-{
- if (gpio_request(OMAP3_EVM_TS_GPIO, "ADS7846 pendown") < 0)
- printk(KERN_ERR "can't get ads7846 pen down GPIO\n");
-
- gpio_direction_input(OMAP3_EVM_TS_GPIO);
- gpio_set_debounce(OMAP3_EVM_TS_GPIO, 310);
-}
-
-static int ads7846_get_pendown_state(void)
-{
- return !gpio_get_value(OMAP3_EVM_TS_GPIO);
-}
-
-static struct ads7846_platform_data ads7846_config = {
- .x_max = 0x0fff,
- .y_max = 0x0fff,
- .x_plate_ohms = 180,
- .pressure_max = 255,
- .debounce_max = 10,
- .debounce_tol = 3,
- .debounce_rep = 1,
- .get_pendown_state = ads7846_get_pendown_state,
- .keep_vref_on = 1,
- .settle_delay_usecs = 150,
- .wakeup = true,
-};
-
-static struct omap2_mcspi_device_config ads7846_mcspi_config = {
- .turbo_mode = 0,
- .single_channel = 1, /* 0: slave, 1: master */
-};
-
-static struct spi_board_info omap3evm_spi_board_info[] = {
- [0] = {
- .modalias = "ads7846",
- .bus_num = 1,
- .chip_select = 0,
- .max_speed_hz = 1500000,
- .controller_data = &ads7846_mcspi_config,
- .irq = OMAP_GPIO_IRQ(OMAP3_EVM_TS_GPIO),
- .platform_data = &ads7846_config,
- },
-};
-
static struct omap_board_config_kernel omap3_evm_config[] __initdata = {
};
.power = 100,
};
+static struct gpio omap3_evm_ehci_gpios[] __initdata = {
+ { OMAP3_EVM_EHCI_VBUS, GPIOF_OUT_INIT_HIGH, "enable EHCI VBUS" },
+ { OMAP3_EVM_EHCI_SELECT, GPIOF_OUT_INIT_LOW, "select EHCI port" },
+};
+
static void __init omap3_evm_init(void)
{
omap3_evm_get_revision();
omap_display_init(&omap3_evm_dss_data);
- spi_register_board_info(omap3evm_spi_board_info,
- ARRAY_SIZE(omap3evm_spi_board_info));
-
omap_serial_init();
/* OMAP3EVM uses ISP1504 phy and so register nop transceiver */
if (get_omap3_evm_rev() >= OMAP3EVM_BOARD_GEN_2) {
/* enable EHCI VBUS using GPIO22 */
- omap_mux_init_gpio(22, OMAP_PIN_INPUT_PULLUP);
- gpio_request(OMAP3_EVM_EHCI_VBUS, "enable EHCI VBUS");
- gpio_direction_output(OMAP3_EVM_EHCI_VBUS, 0);
- gpio_set_value(OMAP3_EVM_EHCI_VBUS, 1);
-
+ omap_mux_init_gpio(OMAP3_EVM_EHCI_VBUS, OMAP_PIN_INPUT_PULLUP);
/* Select EHCI port on main board */
- omap_mux_init_gpio(61, OMAP_PIN_INPUT_PULLUP);
- gpio_request(OMAP3_EVM_EHCI_SELECT, "select EHCI port");
- gpio_direction_output(OMAP3_EVM_EHCI_SELECT, 0);
- gpio_set_value(OMAP3_EVM_EHCI_SELECT, 0);
+ omap_mux_init_gpio(OMAP3_EVM_EHCI_SELECT,
+ OMAP_PIN_INPUT_PULLUP);
+ gpio_request_array(omap3_evm_ehci_gpios,
+ ARRAY_SIZE(omap3_evm_ehci_gpios));
/* setup EHCI phy reset config */
omap_mux_init_gpio(21, OMAP_PIN_INPUT_PULLUP);
}
usb_musb_init(&musb_board_data);
usbhs_init(&usbhs_bdata);
- ads7846_dev_init();
+ omap_ads7846_init(1, OMAP3_EVM_TS_GPIO, 310, NULL);
omap3evm_init_smsc911x();
omap3_evm_display_init();
#include "hsmmc.h"
#include "timer-gp.h"
#include "control.h"
+#include "common-board-devices.h"
#include <plat/mux.h>
#include <plat/board.h>
.vmmc1 = &omap3logic_vmmc1,
};
-static struct i2c_board_info __initdata omap3logic_i2c_boardinfo[] = {
- {
- I2C_BOARD_INFO("twl4030", 0x48),
- .flags = I2C_CLIENT_WAKE,
- .irq = INT_34XX_SYS_NIRQ,
- .platform_data = &omap3logic_twldata,
- },
-};
-
static int __init omap3logic_i2c_init(void)
{
- omap_register_i2c_bus(1, 2600, omap3logic_i2c_boardinfo,
- ARRAY_SIZE(omap3logic_i2c_boardinfo));
+ omap3_pmic_init("twl4030", &omap3logic_twldata);
return 0;
}
.cs = OMAP3LOGIC_SMSC911X_CS,
.gpio_irq = -EINVAL,
.gpio_reset = -EINVAL,
- .flags = IORESOURCE_IRQ_LOWLEVEL,
};
/* TODO/FIXME (comment by Peter Barada, LogicPD):
#include <linux/platform_device.h>
#include <linux/spi/spi.h>
-#include <linux/spi/ads7846.h>
#include <linux/regulator/machine.h>
#include <linux/i2c/twl.h>
#include <linux/wl12xx.h>
#include "mux.h"
#include "sdram-micron-mt46h32m32lf-6.h"
#include "hsmmc.h"
+#include "common-board-devices.h"
#define PANDORA_WIFI_IRQ_GPIO 21
#define PANDORA_WIFI_NRESET_GPIO 23
/* gpio + 13 drives 32kHz buffer for wifi module */
gpio_32khz = gpio + 13;
- ret = gpio_request(gpio_32khz, "wifi 32kHz");
+ ret = gpio_request_one(gpio_32khz, GPIOF_OUT_INIT_HIGH, "wifi 32kHz");
if (ret < 0) {
pr_err("Cannot get GPIO line %d, ret=%d\n", gpio_32khz, ret);
- goto fail;
- }
-
- ret = gpio_direction_output(gpio_32khz, 1);
- if (ret < 0) {
- pr_err("Cannot set GPIO line %d, ret=%d\n", gpio_32khz, ret);
- goto fail_direction;
+ return -ENODEV;
}
return 0;
-
-fail_direction:
- gpio_free(gpio_32khz);
-fail:
- return -ENODEV;
}
static struct twl4030_gpio_platform_data omap3pandora_gpio_data = {
.bci = &pandora_bci_data,
};
-static struct i2c_board_info __initdata omap3pandora_i2c_boardinfo[] = {
- {
- I2C_BOARD_INFO("tps65950", 0x48),
- .flags = I2C_CLIENT_WAKE,
- .irq = INT_34XX_SYS_NIRQ,
- .platform_data = &omap3pandora_twldata,
- },
-};
-
static struct i2c_board_info __initdata omap3pandora_i2c3_boardinfo[] = {
{
I2C_BOARD_INFO("bq27500", 0x55),
static int __init omap3pandora_i2c_init(void)
{
- omap_register_i2c_bus(1, 2600, omap3pandora_i2c_boardinfo,
- ARRAY_SIZE(omap3pandora_i2c_boardinfo));
+ omap3_pmic_init("tps65950", &omap3pandora_twldata);
/* i2c2 pins are not connected */
omap_register_i2c_bus(3, 100, omap3pandora_i2c3_boardinfo,
ARRAY_SIZE(omap3pandora_i2c3_boardinfo));
return 0;
}
-static void __init omap3pandora_ads7846_init(void)
-{
- int gpio = OMAP3_PANDORA_TS_GPIO;
- int ret;
-
- ret = gpio_request(gpio, "ads7846_pen_down");
- if (ret < 0) {
- printk(KERN_ERR "Failed to request GPIO %d for "
- "ads7846 pen down IRQ\n", gpio);
- return;
- }
-
- gpio_direction_input(gpio);
-}
-
-static int ads7846_get_pendown_state(void)
-{
- return !gpio_get_value(OMAP3_PANDORA_TS_GPIO);
-}
-
-static struct ads7846_platform_data ads7846_config = {
- .x_max = 0x0fff,
- .y_max = 0x0fff,
- .x_plate_ohms = 180,
- .pressure_max = 255,
- .debounce_max = 10,
- .debounce_tol = 3,
- .debounce_rep = 1,
- .get_pendown_state = ads7846_get_pendown_state,
- .keep_vref_on = 1,
-};
-
-static struct omap2_mcspi_device_config ads7846_mcspi_config = {
- .turbo_mode = 0,
- .single_channel = 1, /* 0: slave, 1: master */
-};
-
static struct spi_board_info omap3pandora_spi_board_info[] __initdata = {
{
- .modalias = "ads7846",
- .bus_num = 1,
- .chip_select = 0,
- .max_speed_hz = 1500000,
- .controller_data = &ads7846_mcspi_config,
- .irq = OMAP_GPIO_IRQ(OMAP3_PANDORA_TS_GPIO),
- .platform_data = &ads7846_config,
- }, {
.modalias = "tpo_td043mtea1_panel_spi",
.bus_num = 1,
.chip_select = 1,
memset(&pandora_wl1251_pdata, 0, sizeof(pandora_wl1251_pdata));
- ret = gpio_request(PANDORA_WIFI_IRQ_GPIO, "wl1251 irq");
+ ret = gpio_request_one(PANDORA_WIFI_IRQ_GPIO, GPIOF_IN, "wl1251 irq");
if (ret < 0)
goto fail;
- ret = gpio_direction_input(PANDORA_WIFI_IRQ_GPIO);
- if (ret < 0)
- goto fail_irq;
-
pandora_wl1251_pdata.irq = gpio_to_irq(PANDORA_WIFI_IRQ_GPIO);
if (pandora_wl1251_pdata.irq < 0)
goto fail_irq;
};
#endif
-static struct omap_musb_board_data musb_board_data = {
- .interface_type = MUSB_INTERFACE_ULPI,
- .mode = MUSB_OTG,
- .power = 100,
-};
-
static void __init omap3pandora_init(void)
{
omap3_mux_init(board_mux, OMAP_PACKAGE_CBB);
omap_serial_init();
spi_register_board_info(omap3pandora_spi_board_info,
ARRAY_SIZE(omap3pandora_spi_board_info));
- omap3pandora_ads7846_init();
+ omap_ads7846_init(1, OMAP3_PANDORA_TS_GPIO, 0, NULL);
usbhs_init(&usbhs_bdata);
- usb_musb_init(&musb_board_data);
+ usb_musb_init(NULL);
gpmc_nand_init(&pandora_nand_data);
/* Ensure SDRC pins are mux'd for self-refresh */
#include <plat/mcspi.h>
#include <linux/input/matrix_keypad.h>
#include <linux/spi/spi.h>
-#include <linux/spi/ads7846.h>
#include <linux/interrupt.h>
#include <linux/smsc911x.h>
#include <linux/i2c/at24.h>
#include "mux.h"
#include "hsmmc.h"
#include "timer-gp.h"
+#include "common-board-devices.h"
#if defined(CONFIG_SMSC911X) || defined(CONFIG_SMSC911X_MODULE)
+#include <plat/gpmc-smsc911x.h>
+
#define OMAP3STALKER_ETHR_START 0x2c000000
#define OMAP3STALKER_ETHR_SIZE 1024
#define OMAP3STALKER_ETHR_GPIO_IRQ 19
#define OMAP3STALKER_SMC911X_CS 5
-static struct resource omap3stalker_smsc911x_resources[] = {
- [0] = {
- .start = OMAP3STALKER_ETHR_START,
- .end =
- (OMAP3STALKER_ETHR_START + OMAP3STALKER_ETHR_SIZE - 1),
- .flags = IORESOURCE_MEM,
- },
- [1] = {
- .start = OMAP_GPIO_IRQ(OMAP3STALKER_ETHR_GPIO_IRQ),
- .end = OMAP_GPIO_IRQ(OMAP3STALKER_ETHR_GPIO_IRQ),
- .flags = (IORESOURCE_IRQ | IRQF_TRIGGER_LOW),
- },
-};
-
-static struct smsc911x_platform_config smsc911x_config = {
- .phy_interface = PHY_INTERFACE_MODE_MII,
- .irq_polarity = SMSC911X_IRQ_POLARITY_ACTIVE_LOW,
- .irq_type = SMSC911X_IRQ_TYPE_OPEN_DRAIN,
+static struct omap_smsc911x_platform_data smsc911x_cfg = {
+ .cs = OMAP3STALKER_SMC911X_CS,
+ .gpio_irq = OMAP3STALKER_ETHR_GPIO_IRQ,
+ .gpio_reset = -EINVAL,
.flags = (SMSC911X_USE_32BIT | SMSC911X_SAVE_MAC_ADDRESS),
};
-static struct platform_device omap3stalker_smsc911x_device = {
- .name = "smsc911x",
- .id = -1,
- .num_resources = ARRAY_SIZE(omap3stalker_smsc911x_resources),
- .resource = &omap3stalker_smsc911x_resources[0],
- .dev = {
- .platform_data = &smsc911x_config,
- },
-};
-
static inline void __init omap3stalker_init_eth(void)
{
- int eth_cs;
struct clk *l3ck;
unsigned int rate;
- eth_cs = OMAP3STALKER_SMC911X_CS;
-
l3ck = clk_get(NULL, "l3_ck");
if (IS_ERR(l3ck))
rate = 100000000;
rate = clk_get_rate(l3ck);
omap_mux_init_gpio(19, OMAP_PIN_INPUT_PULLUP);
- if (gpio_request(OMAP3STALKER_ETHR_GPIO_IRQ, "SMC911x irq") < 0) {
- printk(KERN_ERR
- "Failed to request GPIO%d for smc911x IRQ\n",
- OMAP3STALKER_ETHR_GPIO_IRQ);
- return;
- }
-
- gpio_direction_input(OMAP3STALKER_ETHR_GPIO_IRQ);
-
- platform_device_register(&omap3stalker_smsc911x_device);
+ gpmc_smsc911x_init(&smsc911x_cfg);
}
#else
*/
/* TWL4030_GPIO_MAX + 0 == ledA, LCD Backlight control */
- gpio_request(gpio + TWL4030_GPIO_MAX, "EN_LCD_BKL");
- gpio_direction_output(gpio + TWL4030_GPIO_MAX, 0);
+ gpio_request_one(gpio + TWL4030_GPIO_MAX, GPIOF_OUT_INIT_LOW,
+ "EN_LCD_BKL");
/* gpio + 7 == DVI Enable */
- gpio_request(gpio + 7, "EN_DVI");
- gpio_direction_output(gpio + 7, 0);
+ gpio_request_one(gpio + 7, GPIOF_OUT_INIT_LOW, "EN_DVI");
/* TWL4030_GPIO_MAX + 1 == ledB (out, mmc0) */
gpio_leds[2].gpio = gpio + TWL4030_GPIO_MAX + 1;
.codec = &omap3stalker_codec_data,
.vdac = &omap3_stalker_vdac,
.vpll2 = &omap3_stalker_vpll2,
-};
-
-static struct i2c_board_info __initdata omap3stalker_i2c_boardinfo[] = {
- {
- I2C_BOARD_INFO("twl4030", 0x48),
- .flags = I2C_CLIENT_WAKE,
- .irq = INT_34XX_SYS_NIRQ,
- .platform_data = &omap3stalker_twldata,
- },
+ .vmmc1 = &omap3stalker_vmmc1,
+ .vsim = &omap3stalker_vsim,
};
static struct at24_platform_data fram_info = {
static int __init omap3_stalker_i2c_init(void)
{
- /*
- * REVISIT: These entries can be set in omap3evm_twl_data
- * after a merge with MFD tree
- */
- omap3stalker_twldata.vmmc1 = &omap3stalker_vmmc1;
- omap3stalker_twldata.vsim = &omap3stalker_vsim;
-
- omap_register_i2c_bus(1, 2600, omap3stalker_i2c_boardinfo,
- ARRAY_SIZE(omap3stalker_i2c_boardinfo));
+ omap3_pmic_init("twl4030", &omap3stalker_twldata);
omap_register_i2c_bus(2, 400, NULL, 0);
omap_register_i2c_bus(3, 400, omap3stalker_i2c_boardinfo3,
ARRAY_SIZE(omap3stalker_i2c_boardinfo3));
}
#define OMAP3_STALKER_TS_GPIO 175
-static void ads7846_dev_init(void)
-{
- if (gpio_request(OMAP3_STALKER_TS_GPIO, "ADS7846 pendown") < 0)
- printk(KERN_ERR "can't get ads7846 pen down GPIO\n");
-
- gpio_direction_input(OMAP3_STALKER_TS_GPIO);
- gpio_set_debounce(OMAP3_STALKER_TS_GPIO, 310);
-}
-
-static int ads7846_get_pendown_state(void)
-{
- return !gpio_get_value(OMAP3_STALKER_TS_GPIO);
-}
-
-static struct ads7846_platform_data ads7846_config = {
- .x_max = 0x0fff,
- .y_max = 0x0fff,
- .x_plate_ohms = 180,
- .pressure_max = 255,
- .debounce_max = 10,
- .debounce_tol = 3,
- .debounce_rep = 1,
- .get_pendown_state = ads7846_get_pendown_state,
- .keep_vref_on = 1,
- .settle_delay_usecs = 150,
-};
-
-static struct omap2_mcspi_device_config ads7846_mcspi_config = {
- .turbo_mode = 0,
- .single_channel = 1, /* 0: slave, 1: master */
-};
-
-static struct spi_board_info omap3stalker_spi_board_info[] = {
- [0] = {
- .modalias = "ads7846",
- .bus_num = 1,
- .chip_select = 0,
- .max_speed_hz = 1500000,
- .controller_data = &ads7846_mcspi_config,
- .irq = OMAP_GPIO_IRQ(OMAP3_STALKER_TS_GPIO),
- .platform_data = &ads7846_config,
- },
-};
static struct omap_board_config_kernel omap3_stalker_config[] __initdata = {
};
};
#endif
-static struct omap_musb_board_data musb_board_data = {
- .interface_type = MUSB_INTERFACE_ULPI,
- .mode = MUSB_OTG,
- .power = 100,
-};
-
static void __init omap3_stalker_init(void)
{
omap3_mux_init(board_mux, OMAP_PACKAGE_CUS);
ARRAY_SIZE(omap3_stalker_devices));
omap_display_init(&omap3_stalker_dss_data);
- spi_register_board_info(omap3stalker_spi_board_info,
- ARRAY_SIZE(omap3stalker_spi_board_info));
omap_serial_init();
- usb_musb_init(&musb_board_data);
+ usb_musb_init(NULL);
usbhs_init(&usbhs_bdata);
- ads7846_dev_init();
+ omap_ads7846_init(1, OMAP3_STALKER_TS_GPIO, 310, NULL);
omap_mux_init_gpio(21, OMAP_PIN_OUTPUT);
omap_mux_init_gpio(18, OMAP_PIN_INPUT_PULLUP);
#include "mux.h"
#include "hsmmc.h"
#include "timer-gp.h"
+#include "common-board-devices.h"
#include <asm/setup.h>
},
};
-static struct omap_nand_platform_data omap3touchbook_nand_data = {
- .options = NAND_BUSWIDTH_16,
- .parts = omap3touchbook_nand_partitions,
- .nr_parts = ARRAY_SIZE(omap3touchbook_nand_partitions),
- .dma_channel = -1, /* disable DMA in OMAP NAND driver */
- .nand_setup = NULL,
- .dev_ready = NULL,
-};
-
#include "sdram-micron-mt46h32m32lf-6.h"
static struct omap2_hsmmc_info mmc[] = {
/* REVISIT: need ehci-omap hooks for external VBUS
* power switch and overcurrent detect
*/
-
- gpio_request(gpio + 1, "EHCI_nOC");
- gpio_direction_input(gpio + 1);
+ gpio_request_one(gpio + 1, GPIOF_IN, "EHCI_nOC");
/* TWL4030_GPIO_MAX + 0 == ledA, EHCI nEN_USB_PWR (out, active low) */
- gpio_request(gpio + TWL4030_GPIO_MAX, "nEN_USB_PWR");
- gpio_direction_output(gpio + TWL4030_GPIO_MAX, 0);
+ gpio_request_one(gpio + TWL4030_GPIO_MAX, GPIOF_OUT_INIT_LOW,
+ "nEN_USB_PWR");
/* TWL4030_GPIO_MAX + 1 == ledB, PMU_STAT (out, active low LED) */
gpio_leds[2].gpio = gpio + TWL4030_GPIO_MAX + 1;
.vpll2 = &touchbook_vpll2,
};
-static struct i2c_board_info __initdata touchbook_i2c_boardinfo[] = {
- {
- I2C_BOARD_INFO("twl4030", 0x48),
- .flags = I2C_CLIENT_WAKE,
- .irq = INT_34XX_SYS_NIRQ,
- .platform_data = &touchbook_twldata,
- },
-};
-
static struct i2c_board_info __initdata touchBook_i2c_boardinfo[] = {
{
I2C_BOARD_INFO("bq27200", 0x55),
static int __init omap3_touchbook_i2c_init(void)
{
/* Standard TouchBook bus */
- omap_register_i2c_bus(1, 2600, touchbook_i2c_boardinfo,
- ARRAY_SIZE(touchbook_i2c_boardinfo));
+ omap3_pmic_init("twl4030", &touchbook_twldata);
/* Additional TouchBook bus */
omap_register_i2c_bus(3, 100, touchBook_i2c_boardinfo,
return 0;
}
-static void __init omap3_ads7846_init(void)
-{
- if (gpio_request(OMAP3_TS_GPIO, "ads7846_pen_down")) {
- printk(KERN_ERR "Failed to request GPIO %d for "
- "ads7846 pen down IRQ\n", OMAP3_TS_GPIO);
- return;
- }
-
- gpio_direction_input(OMAP3_TS_GPIO);
- gpio_set_debounce(OMAP3_TS_GPIO, 310);
-}
-
-static struct ads7846_platform_data ads7846_config = {
+static struct ads7846_platform_data ads7846_pdata = {
.x_min = 100,
.y_min = 265,
.x_max = 3950,
.keep_vref_on = 1,
};
-static struct omap2_mcspi_device_config ads7846_mcspi_config = {
- .turbo_mode = 0,
- .single_channel = 1, /* 0: slave, 1: master */
-};
-
-static struct spi_board_info omap3_ads7846_spi_board_info[] __initdata = {
- {
- .modalias = "ads7846",
- .bus_num = 4,
- .chip_select = 0,
- .max_speed_hz = 1500000,
- .controller_data = &ads7846_mcspi_config,
- .irq = OMAP_GPIO_IRQ(OMAP3_TS_GPIO),
- .platform_data = &ads7846_config,
- }
-};
-
static struct gpio_led gpio_leds[] = {
{
.name = "touchbook::usr0",
&keys_gpio,
};
-static void __init omap3touchbook_flash_init(void)
-{
- u8 cs = 0;
- u8 nandcs = GPMC_CS_NUM + 1;
-
- /* find out the chip-select on which NAND exists */
- while (cs < GPMC_CS_NUM) {
- u32 ret = 0;
- ret = gpmc_cs_read_reg(cs, GPMC_CS_CONFIG1);
-
- if ((ret & 0xC00) == 0x800) {
- printk(KERN_INFO "Found NAND on CS%d\n", cs);
- if (nandcs > GPMC_CS_NUM)
- nandcs = cs;
- }
- cs++;
- }
-
- if (nandcs > GPMC_CS_NUM) {
- printk(KERN_INFO "NAND: Unable to find configuration "
- "in GPMC\n ");
- return;
- }
-
- if (nandcs < GPMC_CS_NUM) {
- omap3touchbook_nand_data.cs = nandcs;
-
- printk(KERN_INFO "Registering NAND on CS%d\n", nandcs);
- if (gpmc_nand_init(&omap3touchbook_nand_data) < 0)
- printk(KERN_ERR "Unable to register NAND device\n");
- }
-}
-
static const struct usbhs_omap_board_data usbhs_bdata __initconst = {
.port_mode[0] = OMAP_EHCI_PORT_MODE_PHY,
static void omap3_touchbook_poweroff(void)
{
- int r;
+ int pwr_off = TB_KILL_POWER_GPIO;
- r = gpio_request(TB_KILL_POWER_GPIO, "DVI reset");
- if (r < 0) {
+ if (gpio_request_one(pwr_off, GPIOF_OUT_INIT_LOW, "DVI reset") < 0)
printk(KERN_ERR "Unable to get kill power GPIO\n");
- return;
- }
-
- gpio_direction_output(TB_KILL_POWER_GPIO, 0);
}
static int __init early_touchbook_revision(char *p)
}
early_param("tbr", early_touchbook_revision);
-static struct omap_musb_board_data musb_board_data = {
- .interface_type = MUSB_INTERFACE_ULPI,
- .mode = MUSB_OTG,
- .power = 100,
-};
-
static void __init omap3_touchbook_init(void)
{
omap3_mux_init(board_mux, OMAP_PACKAGE_CBB);
omap_serial_init();
omap_mux_init_gpio(170, OMAP_PIN_INPUT);
- gpio_request(176, "DVI_nPD");
/* REVISIT leave DVI powered down until it's needed ... */
- gpio_direction_output(176, true);
+ gpio_request_one(176, GPIOF_OUT_INIT_HIGH, "DVI_nPD");
/* Touchscreen and accelerometer */
- spi_register_board_info(omap3_ads7846_spi_board_info,
- ARRAY_SIZE(omap3_ads7846_spi_board_info));
- omap3_ads7846_init();
- usb_musb_init(&musb_board_data);
+ omap_ads7846_init(4, OMAP3_TS_GPIO, 310, &ads7846_pdata);
+ usb_musb_init(NULL);
usbhs_init(&usbhs_bdata);
- omap3touchbook_flash_init();
+ omap_nand_flash_init(NAND_BUSWIDTH_16, omap3touchbook_nand_partitions,
+ ARRAY_SIZE(omap3touchbook_nand_partitions));
/* Ensure SDRC pins are mux'd for self-refresh */
omap_mux_init_signal("sdrc_cke0", OMAP_PIN_OUTPUT);
#include "hsmmc.h"
#include "control.h"
#include "mux.h"
+#include "common-board-devices.h"
#define GPIO_HUB_POWER 1
#define GPIO_HUB_NRESET 62
.reset_gpio_port[2] = -EINVAL
};
+static struct gpio panda_ehci_gpios[] __initdata = {
+ { GPIO_HUB_POWER, GPIOF_OUT_INIT_LOW, "hub_power" },
+ { GPIO_HUB_NRESET, GPIOF_OUT_INIT_LOW, "hub_nreset" },
+};
+
static void __init omap4_ehci_init(void)
{
int ret;
phy_ref_clk = clk_get(NULL, "auxclk3_ck");
if (IS_ERR(phy_ref_clk)) {
pr_err("Cannot request auxclk3\n");
- goto error1;
+ return;
}
clk_set_rate(phy_ref_clk, 19200000);
clk_enable(phy_ref_clk);
- /* disable the power to the usb hub prior to init */
- ret = gpio_request(GPIO_HUB_POWER, "hub_power");
+ /* disable the power to the usb hub prior to init and reset phy+hub */
+ ret = gpio_request_array(panda_ehci_gpios,
+ ARRAY_SIZE(panda_ehci_gpios));
if (ret) {
- pr_err("Cannot request GPIO %d\n", GPIO_HUB_POWER);
- goto error1;
+ pr_err("Unable to initialize EHCI power/reset\n");
+ return;
}
- gpio_export(GPIO_HUB_POWER, 0);
- gpio_direction_output(GPIO_HUB_POWER, 0);
- gpio_set_value(GPIO_HUB_POWER, 0);
- /* reset phy+hub */
- ret = gpio_request(GPIO_HUB_NRESET, "hub_nreset");
- if (ret) {
- pr_err("Cannot request GPIO %d\n", GPIO_HUB_NRESET);
- goto error2;
- }
+ gpio_export(GPIO_HUB_POWER, 0);
gpio_export(GPIO_HUB_NRESET, 0);
- gpio_direction_output(GPIO_HUB_NRESET, 0);
- gpio_set_value(GPIO_HUB_NRESET, 0);
gpio_set_value(GPIO_HUB_NRESET, 1);
usbhs_init(&usbhs_bdata);
/* enable power to hub */
gpio_set_value(GPIO_HUB_POWER, 1);
- return;
-
-error2:
- gpio_free(GPIO_HUB_POWER);
-error1:
- pr_err("Unable to initialize EHCI power/reset\n");
- return;
-
}
static struct omap_musb_board_data musb_board_data = {
.usb = &omap4_usbphy_data,
};
-static struct i2c_board_info __initdata omap4_panda_i2c_boardinfo[] = {
- {
- I2C_BOARD_INFO("twl6030", 0x48),
- .flags = I2C_CLIENT_WAKE,
- .irq = OMAP44XX_IRQ_SYS_1N,
- .platform_data = &omap4_panda_twldata,
- },
-};
-
/*
* Display monitor features are burnt in their EEPROM as EDID data. The EEPROM
* is connected as I2C slave device, and can be accessed at address 0x50
static int __init omap4_panda_i2c_init(void)
{
- /*
- * Phoenix Audio IC needs I2C1 to
- * start with 400 KHz or less
- */
- omap_register_i2c_bus(1, 400, omap4_panda_i2c_boardinfo,
- ARRAY_SIZE(omap4_panda_i2c_boardinfo));
+ omap4_pmic_init("twl6030", &omap4_panda_twldata);
omap_register_i2c_bus(2, 400, NULL, 0);
/*
* Bus 3 is attached to the DVI port where devices like the pico DLP
OMAP_PIN_INPUT_PULLUP);
}
+static struct gpio panda_hdmi_gpios[] = {
+ { HDMI_GPIO_HPD, GPIOF_OUT_INIT_HIGH, "hdmi_gpio_hpd" },
+ { HDMI_GPIO_LS_OE, GPIOF_OUT_INIT_HIGH, "hdmi_gpio_ls_oe" },
+};
+
static int omap4_panda_panel_enable_hdmi(struct omap_dss_device *dssdev)
{
int status;
- status = gpio_request_one(HDMI_GPIO_HPD, GPIOF_OUT_INIT_HIGH,
- "hdmi_gpio_hpd");
- if (status) {
- pr_err("Cannot request GPIO %d\n", HDMI_GPIO_HPD);
- return status;
- }
- status = gpio_request_one(HDMI_GPIO_LS_OE, GPIOF_OUT_INIT_HIGH,
- "hdmi_gpio_ls_oe");
- if (status) {
- pr_err("Cannot request GPIO %d\n", HDMI_GPIO_LS_OE);
- goto error1;
- }
-
- return 0;
-
-error1:
- gpio_free(HDMI_GPIO_HPD);
+ status = gpio_request_array(panda_hdmi_gpios,
+ ARRAY_SIZE(panda_hdmi_gpios));
+ if (status)
+ pr_err("Cannot request HDMI GPIOs\n");
return status;
}
#include "mux.h"
#include "sdram-micron-mt46h32m32lf-6.h"
#include "hsmmc.h"
+#include "common-board-devices.h"
#define OVERO_GPIO_BT_XGATE 15
#define OVERO_GPIO_W2W_NRESET 16
#if defined(CONFIG_TOUCHSCREEN_ADS7846) || \
defined(CONFIG_TOUCHSCREEN_ADS7846_MODULE)
-#include <linux/spi/ads7846.h>
-
-static struct omap2_mcspi_device_config ads7846_mcspi_config = {
- .turbo_mode = 0,
- .single_channel = 1, /* 0: slave, 1: master */
-};
-
-static int ads7846_get_pendown_state(void)
-{
- return !gpio_get_value(OVERO_GPIO_PENDOWN);
-}
-
-static struct ads7846_platform_data ads7846_config = {
- .x_max = 0x0fff,
- .y_max = 0x0fff,
- .x_plate_ohms = 180,
- .pressure_max = 255,
- .debounce_max = 10,
- .debounce_tol = 3,
- .debounce_rep = 1,
- .get_pendown_state = ads7846_get_pendown_state,
- .keep_vref_on = 1,
-};
-
/* fixed regulator for ads7846 */
static struct regulator_consumer_supply ads7846_supply =
REGULATOR_SUPPLY("vcc", "spi1.0");
static void __init overo_ads7846_init(void)
{
- if ((gpio_request(OVERO_GPIO_PENDOWN, "ADS7846_PENDOWN") == 0) &&
- (gpio_direction_input(OVERO_GPIO_PENDOWN) == 0)) {
- gpio_export(OVERO_GPIO_PENDOWN, 0);
- } else {
- printk(KERN_ERR "could not obtain gpio for ADS7846_PENDOWN\n");
- return;
- }
-
+ omap_ads7846_init(1, OVERO_GPIO_PENDOWN, 0, NULL);
platform_device_register(&vads7846_device);
}
#if defined(CONFIG_SMSC911X) || defined(CONFIG_SMSC911X_MODULE)
#include <linux/smsc911x.h>
+#include <plat/gpmc-smsc911x.h>
-static struct resource overo_smsc911x_resources[] = {
- {
- .name = "smsc911x-memory",
- .flags = IORESOURCE_MEM,
- },
- {
- .flags = IORESOURCE_IRQ | IORESOURCE_IRQ_LOWLEVEL,
- },
-};
-
-static struct resource overo_smsc911x2_resources[] = {
- {
- .name = "smsc911x2-memory",
- .flags = IORESOURCE_MEM,
- },
- {
- .flags = IORESOURCE_IRQ | IORESOURCE_IRQ_LOWLEVEL,
- },
-};
-
-static struct smsc911x_platform_config overo_smsc911x_config = {
- .irq_polarity = SMSC911X_IRQ_POLARITY_ACTIVE_LOW,
- .irq_type = SMSC911X_IRQ_TYPE_OPEN_DRAIN,
- .flags = SMSC911X_USE_32BIT ,
- .phy_interface = PHY_INTERFACE_MODE_MII,
-};
-
-static struct platform_device overo_smsc911x_device = {
- .name = "smsc911x",
+static struct omap_smsc911x_platform_data smsc911x_cfg = {
.id = 0,
- .num_resources = ARRAY_SIZE(overo_smsc911x_resources),
- .resource = overo_smsc911x_resources,
- .dev = {
- .platform_data = &overo_smsc911x_config,
- },
+ .cs = OVERO_SMSC911X_CS,
+ .gpio_irq = OVERO_SMSC911X_GPIO,
+ .gpio_reset = -EINVAL,
+ .flags = SMSC911X_USE_32BIT,
};
-static struct platform_device overo_smsc911x2_device = {
- .name = "smsc911x",
+static struct omap_smsc911x_platform_data smsc911x2_cfg = {
.id = 1,
- .num_resources = ARRAY_SIZE(overo_smsc911x2_resources),
- .resource = overo_smsc911x2_resources,
- .dev = {
- .platform_data = &overo_smsc911x_config,
- },
+ .cs = OVERO_SMSC911X2_CS,
+ .gpio_irq = OVERO_SMSC911X2_GPIO,
+ .gpio_reset = -EINVAL,
+ .flags = SMSC911X_USE_32BIT,
};
-static struct platform_device *smsc911x_devices[] = {
- &overo_smsc911x_device,
- &overo_smsc911x2_device,
-};
-
-static inline void __init overo_init_smsc911x(void)
+static void __init overo_init_smsc911x(void)
{
- unsigned long cs_mem_base, cs_mem_base2;
-
- /* set up first smsc911x chip */
-
- if (gpmc_cs_request(OVERO_SMSC911X_CS, SZ_16M, &cs_mem_base) < 0) {
- printk(KERN_ERR "Failed request for GPMC mem for smsc911x\n");
- return;
- }
-
- overo_smsc911x_resources[0].start = cs_mem_base + 0x0;
- overo_smsc911x_resources[0].end = cs_mem_base + 0xff;
-
- if ((gpio_request(OVERO_SMSC911X_GPIO, "SMSC911X IRQ") == 0) &&
- (gpio_direction_input(OVERO_SMSC911X_GPIO) == 0)) {
- gpio_export(OVERO_SMSC911X_GPIO, 0);
- } else {
- printk(KERN_ERR "could not obtain gpio for SMSC911X IRQ\n");
- return;
- }
-
- overo_smsc911x_resources[1].start = OMAP_GPIO_IRQ(OVERO_SMSC911X_GPIO);
- overo_smsc911x_resources[1].end = 0;
-
- /* set up second smsc911x chip */
-
- if (gpmc_cs_request(OVERO_SMSC911X2_CS, SZ_16M, &cs_mem_base2) < 0) {
- printk(KERN_ERR "Failed request for GPMC mem for smsc911x2\n");
- return;
- }
-
- overo_smsc911x2_resources[0].start = cs_mem_base2 + 0x0;
- overo_smsc911x2_resources[0].end = cs_mem_base2 + 0xff;
-
- if ((gpio_request(OVERO_SMSC911X2_GPIO, "SMSC911X2 IRQ") == 0) &&
- (gpio_direction_input(OVERO_SMSC911X2_GPIO) == 0)) {
- gpio_export(OVERO_SMSC911X2_GPIO, 0);
- } else {
- printk(KERN_ERR "could not obtain gpio for SMSC911X2 IRQ\n");
- return;
- }
-
- overo_smsc911x2_resources[1].start = OMAP_GPIO_IRQ(OVERO_SMSC911X2_GPIO);
- overo_smsc911x2_resources[1].end = 0;
-
- platform_add_devices(smsc911x_devices, ARRAY_SIZE(smsc911x_devices));
+ gpmc_smsc911x_init(&smsc911x_cfg);
+ gpmc_smsc911x_init(&smsc911x2_cfg);
}
#else
#define OVERO_GPIO_LCD_EN 144
#define OVERO_GPIO_LCD_BL 145
+static struct gpio overo_dss_gpios[] __initdata = {
+ { OVERO_GPIO_LCD_EN, GPIOF_OUT_INIT_HIGH, "OVERO_GPIO_LCD_EN" },
+ { OVERO_GPIO_LCD_BL, GPIOF_OUT_INIT_HIGH, "OVERO_GPIO_LCD_BL" },
+};
+
static void __init overo_display_init(void)
{
- if ((gpio_request(OVERO_GPIO_LCD_EN, "OVERO_GPIO_LCD_EN") == 0) &&
- (gpio_direction_output(OVERO_GPIO_LCD_EN, 1) == 0))
- gpio_export(OVERO_GPIO_LCD_EN, 0);
- else
- printk(KERN_ERR "could not obtain gpio for "
- "OVERO_GPIO_LCD_EN\n");
+ if (gpio_request_array(overo_dss_gpios, ARRAY_SIZE(overo_dss_gpios))) {
+ printk(KERN_ERR "could not obtain DSS control GPIOs\n");
+ return;
+ }
- if ((gpio_request(OVERO_GPIO_LCD_BL, "OVERO_GPIO_LCD_BL") == 0) &&
- (gpio_direction_output(OVERO_GPIO_LCD_BL, 1) == 0))
- gpio_export(OVERO_GPIO_LCD_BL, 0);
- else
- printk(KERN_ERR "could not obtain gpio for "
- "OVERO_GPIO_LCD_BL\n");
+ gpio_export(OVERO_GPIO_LCD_EN, 0);
+ gpio_export(OVERO_GPIO_LCD_BL, 0);
}
static int overo_panel_enable_dvi(struct omap_dss_device *dssdev)
},
};
-static struct omap_nand_platform_data overo_nand_data = {
- .parts = overo_nand_partitions,
- .nr_parts = ARRAY_SIZE(overo_nand_partitions),
- .dma_channel = -1, /* disable DMA in OMAP NAND driver */
-};
-
-static void __init overo_flash_init(void)
-{
- u8 cs = 0;
- u8 nandcs = GPMC_CS_NUM + 1;
-
- /* find out the chip-select on which NAND exists */
- while (cs < GPMC_CS_NUM) {
- u32 ret = 0;
- ret = gpmc_cs_read_reg(cs, GPMC_CS_CONFIG1);
-
- if ((ret & 0xC00) == 0x800) {
- printk(KERN_INFO "Found NAND on CS%d\n", cs);
- if (nandcs > GPMC_CS_NUM)
- nandcs = cs;
- }
- cs++;
- }
-
- if (nandcs > GPMC_CS_NUM) {
- printk(KERN_INFO "NAND: Unable to find configuration "
- "in GPMC\n ");
- return;
- }
-
- if (nandcs < GPMC_CS_NUM) {
- overo_nand_data.cs = nandcs;
-
- printk(KERN_INFO "Registering NAND on CS%d\n", nandcs);
- if (gpmc_nand_init(&overo_nand_data) < 0)
- printk(KERN_ERR "Unable to register NAND device\n");
- }
-}
-
static struct omap2_hsmmc_info mmc[] = {
{
.mmc = 1,
.vpll2 = &overo_vpll2,
};
-static struct i2c_board_info __initdata overo_i2c_boardinfo[] = {
- {
- I2C_BOARD_INFO("tps65950", 0x48),
- .flags = I2C_CLIENT_WAKE,
- .irq = INT_34XX_SYS_NIRQ,
- .platform_data = &overo_twldata,
- },
-};
-
static int __init overo_i2c_init(void)
{
- omap_register_i2c_bus(1, 2600, overo_i2c_boardinfo,
- ARRAY_SIZE(overo_i2c_boardinfo));
+ omap3_pmic_init("tps65950", &overo_twldata);
/* i2c2 pins are used for gpio */
omap_register_i2c_bus(3, 400, NULL, 0);
return 0;
}
static struct spi_board_info overo_spi_board_info[] __initdata = {
-#if defined(CONFIG_TOUCHSCREEN_ADS7846) || \
- defined(CONFIG_TOUCHSCREEN_ADS7846_MODULE)
- {
- .modalias = "ads7846",
- .bus_num = 1,
- .chip_select = 0,
- .max_speed_hz = 1500000,
- .controller_data = &ads7846_mcspi_config,
- .irq = OMAP_GPIO_IRQ(OVERO_GPIO_PENDOWN),
- .platform_data = &ads7846_config,
- },
-#endif
#if defined(CONFIG_PANEL_LGPHILIPS_LB035Q02) || \
defined(CONFIG_PANEL_LGPHILIPS_LB035Q02_MODULE)
{
};
#endif
-static struct omap_musb_board_data musb_board_data = {
- .interface_type = MUSB_INTERFACE_ULPI,
- .mode = MUSB_OTG,
- .power = 100,
+static struct gpio overo_bt_gpios[] __initdata = {
+ { OVERO_GPIO_BT_XGATE, GPIOF_OUT_INIT_LOW, "lcd enable" },
+ { OVERO_GPIO_BT_NRESET, GPIOF_OUT_INIT_HIGH, "lcd bl enable" },
};
static void __init overo_init(void)
{
+ int ret;
+
omap3_mux_init(board_mux, OMAP_PACKAGE_CBB);
overo_i2c_init();
omap_display_init(&overo_dss_data);
omap_serial_init();
- overo_flash_init();
- usb_musb_init(&musb_board_data);
+ omap_nand_flash_init(0, overo_nand_partitions,
+ ARRAY_SIZE(overo_nand_partitions));
+ usb_musb_init(NULL);
usbhs_init(&usbhs_bdata);
overo_spi_init();
overo_ads7846_init();
omap_mux_init_signal("sdrc_cke0", OMAP_PIN_OUTPUT);
omap_mux_init_signal("sdrc_cke1", OMAP_PIN_OUTPUT);
- if ((gpio_request(OVERO_GPIO_W2W_NRESET,
- "OVERO_GPIO_W2W_NRESET") == 0) &&
- (gpio_direction_output(OVERO_GPIO_W2W_NRESET, 1) == 0)) {
+ ret = gpio_request_one(OVERO_GPIO_W2W_NRESET, GPIOF_OUT_INIT_HIGH,
+ "OVERO_GPIO_W2W_NRESET");
+ if (ret == 0) {
gpio_export(OVERO_GPIO_W2W_NRESET, 0);
gpio_set_value(OVERO_GPIO_W2W_NRESET, 0);
udelay(10);
"OVERO_GPIO_W2W_NRESET\n");
}
- if ((gpio_request(OVERO_GPIO_BT_XGATE, "OVERO_GPIO_BT_XGATE") == 0) &&
- (gpio_direction_output(OVERO_GPIO_BT_XGATE, 0) == 0))
+ ret = gpio_request_array(overo_bt_gpios, ARRAY_SIZE(overo_bt_gpios));
+ if (ret) {
+ pr_err("%s: could not obtain BT gpios\n", __func__);
+ } else {
gpio_export(OVERO_GPIO_BT_XGATE, 0);
- else
- printk(KERN_ERR "could not obtain gpio for OVERO_GPIO_BT_XGATE\n");
-
- if ((gpio_request(OVERO_GPIO_BT_NRESET, "OVERO_GPIO_BT_NRESET") == 0) &&
- (gpio_direction_output(OVERO_GPIO_BT_NRESET, 1) == 0)) {
gpio_export(OVERO_GPIO_BT_NRESET, 0);
gpio_set_value(OVERO_GPIO_BT_NRESET, 0);
mdelay(6);
gpio_set_value(OVERO_GPIO_BT_NRESET, 1);
- } else {
- printk(KERN_ERR "could not obtain gpio for "
- "OVERO_GPIO_BT_NRESET\n");
}
- if ((gpio_request(OVERO_GPIO_USBH_CPEN, "OVERO_GPIO_USBH_CPEN") == 0) &&
- (gpio_direction_output(OVERO_GPIO_USBH_CPEN, 1) == 0))
+ ret = gpio_request_one(OVERO_GPIO_USBH_CPEN, GPIOF_OUT_INIT_HIGH,
+ "OVERO_GPIO_USBH_CPEN");
+ if (ret == 0)
gpio_export(OVERO_GPIO_USBH_CPEN, 0);
else
printk(KERN_ERR "could not obtain gpio for "
#include "mux.h"
#include "hsmmc.h"
#include "sdram-nokia.h"
+#include "common-board-devices.h"
static struct regulator_consumer_supply rm680_vemmc_consumers[] = {
REGULATOR_SUPPLY("vmmc", "omap_hsmmc.1"),
/* add rest of the children here */
};
-static struct i2c_board_info __initdata rm680_twl_i2c_board_info[] = {
- {
- I2C_BOARD_INFO("twl5031", 0x48),
- .flags = I2C_CLIENT_WAKE,
- .irq = INT_34XX_SYS_NIRQ,
- .platform_data = &rm680_twl_data,
- },
-};
-
static void __init rm680_i2c_init(void)
{
- omap_register_i2c_bus(1, 2900, rm680_twl_i2c_board_info,
- ARRAY_SIZE(rm680_twl_i2c_board_info));
+ omap_pmic_init(1, 2900, "twl5031", INT_34XX_SYS_NIRQ, &rm680_twl_data);
omap_register_i2c_bus(2, 400, NULL, 0);
omap_register_i2c_bus(3, 400, NULL, 0);
}
};
#endif
-static struct omap_musb_board_data rm680_musb_data = {
- .interface_type = MUSB_INTERFACE_ULPI,
- .mode = MUSB_PERIPHERAL,
- .power = 100,
-};
-
static void __init rm680_init(void)
{
omap3_mux_init(board_mux, OMAP_PACKAGE_CBB);
omap_serial_init();
- usb_musb_init(&rm680_musb_data);
+ usb_musb_init(NULL);
rm680_peripherals_init();
}
#include "mux.h"
#include "hsmmc.h"
+#include "common-board-devices.h"
#define SYSTEM_REV_B_USES_VAUX3 0x1699
#define SYSTEM_REV_S_USES_VAUX3 0x8
static int rx51_twlgpio_setup(struct device *dev, unsigned gpio, unsigned n)
{
/* FIXME this gpio setup is just a placeholder for now */
- gpio_request(gpio + 6, "backlight_pwm");
- gpio_direction_output(gpio + 6, 0);
- gpio_request(gpio + 7, "speaker_en");
- gpio_direction_output(gpio + 7, 1);
+ gpio_request_one(gpio + 6, GPIOF_OUT_INIT_LOW, "backlight_pwm");
+ gpio_request_one(gpio + 7, GPIOF_OUT_INIT_HIGH, "speaker_en");
return 0;
}
.power_gpio = 98,
};
-static struct i2c_board_info __initdata rx51_peripherals_i2c_board_info_1[] = {
- {
- I2C_BOARD_INFO("twl5030", 0x48),
- .flags = I2C_CLIENT_WAKE,
- .irq = INT_34XX_SYS_NIRQ,
- .platform_data = &rx51_twldata,
- },
-};
-
/* Audio setup data */
static struct aic3x_setup_data rx51_aic34_setup = {
.gpio_func[0] = AIC3X_GPIO1_FUNC_DISABLED,
rx51_twldata.vaux3 = &rx51_vaux3_cam;
}
rx51_twldata.vmmc2 = &rx51_vmmc2;
- omap_register_i2c_bus(1, 2200, rx51_peripherals_i2c_board_info_1,
- ARRAY_SIZE(rx51_peripherals_i2c_board_info_1));
+ omap_pmic_init(1, 2200, "twl5030", INT_34XX_SYS_NIRQ, &rx51_twldata);
omap_register_i2c_bus(2, 100, rx51_peripherals_i2c_board_info_2,
ARRAY_SIZE(rx51_peripherals_i2c_board_info_2));
omap_register_i2c_bus(3, 400, NULL, 0);
gpio_set_value(RX51_WL1251_POWER_GPIO, enable);
}
+static struct gpio rx51_wl1251_gpios[] __initdata = {
+ { RX51_WL1251_POWER_GPIO, GPIOF_OUT_INIT_LOW, "wl1251 power" },
+ { RX51_WL1251_IRQ_GPIO, GPIOF_IN, "wl1251 irq" },
+};
+
static void __init rx51_init_wl1251(void)
{
int irq, ret;
- ret = gpio_request(RX51_WL1251_POWER_GPIO, "wl1251 power");
+ ret = gpio_request_array(rx51_wl1251_gpios,
+ ARRAY_SIZE(rx51_wl1251_gpios));
if (ret < 0)
goto error;
- ret = gpio_direction_output(RX51_WL1251_POWER_GPIO, 0);
- if (ret < 0)
- goto err_power;
-
- ret = gpio_request(RX51_WL1251_IRQ_GPIO, "wl1251 irq");
- if (ret < 0)
- goto err_power;
-
- ret = gpio_direction_input(RX51_WL1251_IRQ_GPIO);
- if (ret < 0)
- goto err_irq;
-
irq = gpio_to_irq(RX51_WL1251_IRQ_GPIO);
if (irq < 0)
goto err_irq;
err_irq:
gpio_free(RX51_WL1251_IRQ_GPIO);
-
-err_power:
gpio_free(RX51_WL1251_POWER_GPIO);
-
error:
printk(KERN_ERR "wl1251 board initialisation failed\n");
wl1251_pdata.set_power = NULL;
return 0;
}
- if (gpio_request(RX51_LCD_RESET_GPIO, "LCD ACX565AKM reset")) {
+ if (gpio_request_one(RX51_LCD_RESET_GPIO, GPIOF_OUT_INIT_HIGH,
+ "LCD ACX565AKM reset")) {
pr_err("%s failed to get LCD Reset GPIO\n", __func__);
return 0;
}
- gpio_direction_output(RX51_LCD_RESET_GPIO, 1);
-
omap_display_init(&rx51_dss_board_info);
return 0;
}
},
};
+/*
+ * cpuidle C-states definition override from the default values.
+ * The 'exit_latency' field is the sum of sleep and wake-up latencies.
+ */
static struct cpuidle_params rx51_cpuidle_params[] = {
/* C1 */
- {1, 110, 162, 5},
+ {110 + 162, 5 , 1},
/* C2 */
- {1, 106, 180, 309},
+ {106 + 180, 309, 1},
/* C3 */
- {0, 107, 410, 46057},
+ {107 + 410, 46057, 0},
/* C4 */
- {0, 121, 3374, 46057},
+ {121 + 3374, 46057, 0},
/* C5 */
- {1, 855, 1146, 46057},
+ {855 + 1146, 46057, 1},
/* C6 */
- {0, 7580, 4134, 484329},
+ {7580 + 4134, 484329, 0},
/* C7 */
- {1, 7505, 15274, 484329},
+ {7505 + 15274, 484329, 1},
};
static struct omap_lcd_config rx51_lcd_config = {
#include <linux/interrupt.h>
#include <plat/gpmc.h>
+#include <plat/gpmc-smsc911x.h>
#include <mach/board-zoom.h>
#define DEBUG_BASE 0x08000000
#define ZOOM_ETHR_START DEBUG_BASE
-static struct resource zoom_smsc911x_resources[] = {
- [0] = {
- .start = ZOOM_ETHR_START,
- .end = ZOOM_ETHR_START + SZ_4K,
- .flags = IORESOURCE_MEM,
- },
- [1] = {
- .flags = IORESOURCE_IRQ | IORESOURCE_IRQ_LOWLEVEL,
- },
-};
-
-static struct smsc911x_platform_config zoom_smsc911x_config = {
- .irq_polarity = SMSC911X_IRQ_POLARITY_ACTIVE_LOW,
- .irq_type = SMSC911X_IRQ_TYPE_OPEN_DRAIN,
+static struct omap_smsc911x_platform_data zoom_smsc911x_cfg = {
+ .cs = ZOOM_SMSC911X_CS,
+ .gpio_irq = ZOOM_SMSC911X_GPIO,
+ .gpio_reset = -EINVAL,
.flags = SMSC911X_USE_32BIT,
- .phy_interface = PHY_INTERFACE_MODE_MII,
-};
-
-static struct platform_device zoom_smsc911x_device = {
- .name = "smsc911x",
- .id = -1,
- .num_resources = ARRAY_SIZE(zoom_smsc911x_resources),
- .resource = zoom_smsc911x_resources,
- .dev = {
- .platform_data = &zoom_smsc911x_config,
- },
};
static inline void __init zoom_init_smsc911x(void)
{
- int eth_cs;
- unsigned long cs_mem_base;
- int eth_gpio = 0;
-
- eth_cs = ZOOM_SMSC911X_CS;
-
- if (gpmc_cs_request(eth_cs, SZ_16M, &cs_mem_base) < 0) {
- printk(KERN_ERR "Failed to request GPMC mem for smsc911x\n");
- return;
- }
-
- zoom_smsc911x_resources[0].start = cs_mem_base + 0x0;
- zoom_smsc911x_resources[0].end = cs_mem_base + 0xff;
-
- eth_gpio = ZOOM_SMSC911X_GPIO;
-
- zoom_smsc911x_resources[1].start = OMAP_GPIO_IRQ(eth_gpio);
-
- if (gpio_request(eth_gpio, "smsc911x irq") < 0) {
- printk(KERN_ERR "Failed to request GPIO%d for smsc911x IRQ\n",
- eth_gpio);
- return;
- }
- gpio_direction_input(eth_gpio);
+ gpmc_smsc911x_init(&zoom_smsc911x_cfg);
}
static struct plat_serial8250_port serial_platform_data[] = {
quart_gpio = ZOOM_QUADUART_GPIO;
- if (gpio_request(quart_gpio, "TL16CP754C GPIO") < 0) {
+ if (gpio_request_one(quart_gpio, GPIOF_IN, "TL16CP754C GPIO") < 0)
printk(KERN_ERR "Failed to request GPIO%d for TL16CP754C\n",
quart_gpio);
- return;
- }
- gpio_direction_input(quart_gpio);
}
static inline int omap_zoom_debugboard_detect(void)
debug_board_detect = ZOOM_SMSC911X_GPIO;
- if (gpio_request(debug_board_detect, "Zoom debug board detect") < 0) {
+ if (gpio_request_one(debug_board_detect, GPIOF_IN,
+ "Zoom debug board detect") < 0) {
printk(KERN_ERR "Failed to request GPIO%d for Zoom debug"
"board detect\n", debug_board_detect);
return 0;
}
- gpio_direction_input(debug_board_detect);
if (!gpio_get_value(debug_board_detect)) {
ret = 0;
}
static struct platform_device *zoom_devices[] __initdata = {
- &zoom_smsc911x_device,
&zoom_debugboard_serial_device,
};
#define LCD_PANEL_RESET_GPIO_PILOT 55
#define LCD_PANEL_QVGA_GPIO 56
+static struct gpio zoom_lcd_gpios[] __initdata = {
+ { -EINVAL, GPIOF_OUT_INIT_HIGH, "lcd reset" },
+ { LCD_PANEL_QVGA_GPIO, GPIOF_OUT_INIT_HIGH, "lcd qvga" },
+};
+
static void zoom_lcd_panel_init(void)
{
- int ret;
- unsigned char lcd_panel_reset_gpio;
-
- lcd_panel_reset_gpio = (omap_rev() > OMAP3430_REV_ES3_0) ?
+ zoom_lcd_gpios[0].gpio = (omap_rev() > OMAP3430_REV_ES3_0) ?
LCD_PANEL_RESET_GPIO_PROD :
LCD_PANEL_RESET_GPIO_PILOT;
- ret = gpio_request(lcd_panel_reset_gpio, "lcd reset");
- if (ret) {
- pr_err("Failed to get LCD reset GPIO (gpio%d).\n",
- lcd_panel_reset_gpio);
- return;
- }
- gpio_direction_output(lcd_panel_reset_gpio, 1);
-
- ret = gpio_request(LCD_PANEL_QVGA_GPIO, "lcd qvga");
- if (ret) {
- pr_err("Failed to get LCD_PANEL_QVGA_GPIO (gpio%d).\n",
- LCD_PANEL_QVGA_GPIO);
- goto err0;
- }
- gpio_direction_output(LCD_PANEL_QVGA_GPIO, 1);
-
- return;
-err0:
- gpio_free(lcd_panel_reset_gpio);
+ if (gpio_request_array(zoom_lcd_gpios, ARRAY_SIZE(zoom_lcd_gpios)))
+ pr_err("%s: Failed to get LCD GPIOs.\n", __func__);
}
static int zoom_panel_enable_lcd(struct omap_dss_device *dssdev)
#include "mux.h"
#include "hsmmc.h"
+#include "common-board-devices.h"
#define OMAP_ZOOM_WLAN_PMENA_GPIO (101)
#define OMAP_ZOOM_WLAN_IRQ_GPIO (162)
zoom_vsim_supply.dev = mmc[0].dev;
zoom_vmmc2_supply.dev = mmc[1].dev;
- ret = gpio_request(LCD_PANEL_ENABLE_GPIO, "lcd enable");
- if (ret) {
+ ret = gpio_request_one(LCD_PANEL_ENABLE_GPIO, GPIOF_OUT_INIT_LOW,
+ "lcd enable");
+ if (ret)
pr_err("Failed to get LCD_PANEL_ENABLE_GPIO (gpio%d).\n",
LCD_PANEL_ENABLE_GPIO);
- return ret;
- }
- gpio_direction_output(LCD_PANEL_ENABLE_GPIO, 0);
return ret;
}
.vdac = &zoom_vdac,
};
-static struct i2c_board_info __initdata zoom_i2c_boardinfo[] = {
- {
- I2C_BOARD_INFO("twl5030", 0x48),
- .flags = I2C_CLIENT_WAKE,
- .irq = INT_34XX_SYS_NIRQ,
- .platform_data = &zoom_twldata,
- },
-};
-
static int __init omap_i2c_init(void)
{
if (machine_is_omap_zoom2()) {
zoom_audio_data.hs_extmute = 1;
zoom_audio_data.set_hs_extmute = zoom2_set_hs_extmute;
}
- omap_register_i2c_bus(1, 2400, zoom_i2c_boardinfo,
- ARRAY_SIZE(zoom_i2c_boardinfo));
+ omap_pmic_init(1, 2400, "twl5030", INT_34XX_SYS_NIRQ, &zoom_twldata);
omap_register_i2c_bus(2, 400, NULL, 0);
omap_register_i2c_bus(3, 400, NULL, 0);
return 0;
}
-static struct omap_musb_board_data musb_board_data = {
- .interface_type = MUSB_INTERFACE_ULPI,
- .mode = MUSB_OTG,
- .power = 100,
-};
-
static void enable_board_wakeup_source(void)
{
/* T2 interrupt line (keypad) */
omap_i2c_init();
platform_device_register(&omap_vwlan_device);
- usb_musb_init(&musb_board_data);
+ usb_musb_init(NULL);
enable_board_wakeup_source();
omap_serial_init();
}
--- /dev/null
+/*
+ * common-board-devices.c
+ *
+ * Copyright (C) 2011 CompuLab, Ltd.
+ * Author: Mike Rapoport <mike@compulab.co.il>
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License
+ * version 2 as published by the Free Software Foundation.
+ *
+ * This program is distributed in the hope that it will be useful, but
+ * WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU
+ * General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA
+ * 02110-1301 USA
+ *
+ */
+
+#include <linux/i2c.h>
+#include <linux/i2c/twl.h>
+
+#include <linux/gpio.h>
+#include <linux/spi/spi.h>
+#include <linux/spi/ads7846.h>
+
+#include <plat/i2c.h>
+#include <plat/mcspi.h>
+#include <plat/nand.h>
+
+#include "common-board-devices.h"
+
+static struct i2c_board_info __initdata pmic_i2c_board_info = {
+ .addr = 0x48,
+ .flags = I2C_CLIENT_WAKE,
+};
+
+void __init omap_pmic_init(int bus, u32 clkrate,
+ const char *pmic_type, int pmic_irq,
+ struct twl4030_platform_data *pmic_data)
+{
+ strncpy(pmic_i2c_board_info.type, pmic_type,
+ sizeof(pmic_i2c_board_info.type));
+ pmic_i2c_board_info.irq = pmic_irq;
+ pmic_i2c_board_info.platform_data = pmic_data;
+
+ omap_register_i2c_bus(bus, clkrate, &pmic_i2c_board_info, 1);
+}
+
+#if defined(CONFIG_TOUCHSCREEN_ADS7846) || \
+ defined(CONFIG_TOUCHSCREEN_ADS7846_MODULE)
+static struct omap2_mcspi_device_config ads7846_mcspi_config = {
+ .turbo_mode = 0,
+ .single_channel = 1, /* 0: slave, 1: master */
+};
+
+static struct ads7846_platform_data ads7846_config = {
+ .x_max = 0x0fff,
+ .y_max = 0x0fff,
+ .x_plate_ohms = 180,
+ .pressure_max = 255,
+ .debounce_max = 10,
+ .debounce_tol = 3,
+ .debounce_rep = 1,
+ .gpio_pendown = -EINVAL,
+ .keep_vref_on = 1,
+};
+
+static struct spi_board_info ads7846_spi_board_info __initdata = {
+ .modalias = "ads7846",
+ .bus_num = -EINVAL,
+ .chip_select = 0,
+ .max_speed_hz = 1500000,
+ .controller_data = &ads7846_mcspi_config,
+ .irq = -EINVAL,
+ .platform_data = &ads7846_config,
+};
+
+void __init omap_ads7846_init(int bus_num, int gpio_pendown, int gpio_debounce,
+ struct ads7846_platform_data *board_pdata)
+{
+ struct spi_board_info *spi_bi = &ads7846_spi_board_info;
+ int err;
+
+ err = gpio_request(gpio_pendown, "TS PenDown");
+ if (err) {
+ pr_err("Could not obtain gpio for TS PenDown: %d\n", err);
+ return;
+ }
+
+ gpio_direction_input(gpio_pendown);
+ gpio_export(gpio_pendown, 0);
+
+ if (gpio_debounce)
+ gpio_set_debounce(gpio_pendown, gpio_debounce);
+
+ ads7846_config.gpio_pendown = gpio_pendown;
+
+ spi_bi->bus_num = bus_num;
+ spi_bi->irq = OMAP_GPIO_IRQ(gpio_pendown);
+
+ if (board_pdata)
+ spi_bi->platform_data = board_pdata;
+
+ spi_register_board_info(&ads7846_spi_board_info, 1);
+}
+#else
+void __init omap_ads7846_init(int bus_num, int gpio_pendown, int gpio_debounce,
+ struct ads7846_platform_data *board_pdata)
+{
+}
+#endif
+
+#if defined(CONFIG_MTD_NAND_OMAP2) || defined(CONFIG_MTD_NAND_OMAP2_MODULE)
+static struct omap_nand_platform_data nand_data = {
+ .dma_channel = -1, /* disable DMA in OMAP NAND driver */
+};
+
+void __init omap_nand_flash_init(int options, struct mtd_partition *parts,
+ int nr_parts)
+{
+ u8 cs = 0;
+ u8 nandcs = GPMC_CS_NUM + 1;
+
+ /* find out the chip-select on which NAND exists */
+ while (cs < GPMC_CS_NUM) {
+ u32 ret = 0;
+ ret = gpmc_cs_read_reg(cs, GPMC_CS_CONFIG1);
+
+ if ((ret & 0xC00) == 0x800) {
+ printk(KERN_INFO "Found NAND on CS%d\n", cs);
+ if (nandcs > GPMC_CS_NUM)
+ nandcs = cs;
+ }
+ cs++;
+ }
+
+ if (nandcs > GPMC_CS_NUM) {
+ printk(KERN_INFO "NAND: Unable to find configuration "
+ "in GPMC\n ");
+ return;
+ }
+
+ if (nandcs < GPMC_CS_NUM) {
+ nand_data.cs = nandcs;
+ nand_data.parts = parts;
+ nand_data.nr_parts = nr_parts;
+ nand_data.options = options;
+
+ printk(KERN_INFO "Registering NAND on CS%d\n", nandcs);
+ if (gpmc_nand_init(&nand_data) < 0)
+ printk(KERN_ERR "Unable to register NAND device\n");
+ }
+}
+#else
+void __init omap_nand_flash_init(int options, struct mtd_partition *parts,
+ int nr_parts)
+{
+}
+#endif
--- /dev/null
+#ifndef __OMAP_COMMON_BOARD_DEVICES__
+#define __OMAP_COMMON_BOARD_DEVICES__
+
+struct twl4030_platform_data;
+struct mtd_partition;
+
+void omap_pmic_init(int bus, u32 clkrate, const char *pmic_type, int pmic_irq,
+ struct twl4030_platform_data *pmic_data);
+
+static inline void omap2_pmic_init(const char *pmic_type,
+ struct twl4030_platform_data *pmic_data)
+{
+ omap_pmic_init(2, 2600, pmic_type, INT_24XX_SYS_NIRQ, pmic_data);
+}
+
+static inline void omap3_pmic_init(const char *pmic_type,
+ struct twl4030_platform_data *pmic_data)
+{
+ omap_pmic_init(1, 2600, pmic_type, INT_34XX_SYS_NIRQ, pmic_data);
+}
+
+static inline void omap4_pmic_init(const char *pmic_type,
+ struct twl4030_platform_data *pmic_data)
+{
+ /* Phoenix Audio IC needs I2C1 to start with 400 KHz or less */
+ omap_pmic_init(1, 400, pmic_type, OMAP44XX_IRQ_SYS_1N, pmic_data);
+}
+
+struct ads7846_platform_data;
+
+void omap_ads7846_init(int bus_num, int gpio_pendown, int gpio_debounce,
+ struct ads7846_platform_data *board_pdata);
+void omap_nand_flash_init(int opts, struct mtd_partition *parts, int n_parts);
+
+#endif /* __OMAP_COMMON_BOARD_DEVICES__ */
#ifdef CONFIG_CPU_IDLE
-#define OMAP3_MAX_STATES 7
-#define OMAP3_STATE_C1 0 /* C1 - MPU WFI + Core active */
-#define OMAP3_STATE_C2 1 /* C2 - MPU WFI + Core inactive */
-#define OMAP3_STATE_C3 2 /* C3 - MPU CSWR + Core inactive */
-#define OMAP3_STATE_C4 3 /* C4 - MPU OFF + Core iactive */
-#define OMAP3_STATE_C5 4 /* C5 - MPU RET + Core RET */
-#define OMAP3_STATE_C6 5 /* C6 - MPU OFF + Core RET */
-#define OMAP3_STATE_C7 6 /* C7 - MPU OFF + Core OFF */
-
-#define OMAP3_STATE_MAX OMAP3_STATE_C7
-
-#define CPUIDLE_FLAG_CHECK_BM 0x10000 /* use omap3_enter_idle_bm() */
-
-struct omap3_processor_cx {
- u8 valid;
- u8 type;
- u32 sleep_latency;
- u32 wakeup_latency;
- u32 mpu_state;
- u32 core_state;
- u32 threshold;
- u32 flags;
- const char *desc;
-};
-
-struct omap3_processor_cx omap3_power_states[OMAP3_MAX_STATES];
-struct omap3_processor_cx current_cx_state;
-struct powerdomain *mpu_pd, *core_pd, *per_pd;
-struct powerdomain *cam_pd;
-
/*
* The latencies/thresholds for various C states have
* to be configured from the respective board files.
*/
static struct cpuidle_params cpuidle_params_table[] = {
/* C1 */
- {1, 2, 2, 5},
+ {2 + 2, 5, 1},
/* C2 */
- {1, 10, 10, 30},
+ {10 + 10, 30, 1},
/* C3 */
- {1, 50, 50, 300},
+ {50 + 50, 300, 1},
/* C4 */
- {1, 1500, 1800, 4000},
+ {1500 + 1800, 4000, 1},
/* C5 */
- {1, 2500, 7500, 12000},
+ {2500 + 7500, 12000, 1},
/* C6 */
- {1, 3000, 8500, 15000},
+ {3000 + 8500, 15000, 1},
/* C7 */
- {1, 10000, 30000, 300000},
+ {10000 + 30000, 300000, 1},
};
+#define OMAP3_NUM_STATES ARRAY_SIZE(cpuidle_params_table)
-static int omap3_idle_bm_check(void)
-{
- if (!omap3_can_sleep())
- return 1;
- return 0;
-}
+/* Mach specific information to be recorded in the C-state driver_data */
+struct omap3_idle_statedata {
+ u32 mpu_state;
+ u32 core_state;
+ u8 valid;
+};
+struct omap3_idle_statedata omap3_idle_data[OMAP3_NUM_STATES];
+
+struct powerdomain *mpu_pd, *core_pd, *per_pd, *cam_pd;
static int _cpuidle_allow_idle(struct powerdomain *pwrdm,
struct clockdomain *clkdm)
static int omap3_enter_idle(struct cpuidle_device *dev,
struct cpuidle_state *state)
{
- struct omap3_processor_cx *cx = cpuidle_get_statedata(state);
+ struct omap3_idle_statedata *cx = cpuidle_get_statedata(state);
struct timespec ts_preidle, ts_postidle, ts_idle;
u32 mpu_state = cx->mpu_state, core_state = cx->core_state;
- current_cx_state = *cx;
-
/* Used to keep track of the total time in idle */
getnstimeofday(&ts_preidle);
if (omap_irq_pending() || need_resched())
goto return_sleep_time;
- if (cx->type == OMAP3_STATE_C1) {
+ /* Deny idle for C1 */
+ if (state == &dev->states[0]) {
pwrdm_for_each_clkdm(mpu_pd, _cpuidle_deny_idle);
pwrdm_for_each_clkdm(core_pd, _cpuidle_deny_idle);
}
/* Execute ARM wfi */
omap_sram_idle();
- if (cx->type == OMAP3_STATE_C1) {
+ /* Re-allow idle for C1 */
+ if (state == &dev->states[0]) {
pwrdm_for_each_clkdm(mpu_pd, _cpuidle_allow_idle);
pwrdm_for_each_clkdm(core_pd, _cpuidle_allow_idle);
}
}
/**
- * next_valid_state - Find next valid c-state
+ * next_valid_state - Find next valid C-state
* @dev: cpuidle device
- * @state: Currently selected c-state
+ * @state: Currently selected C-state
*
* If the current state is valid, it is returned back to the caller.
* Else, this function searches for a lower c-state which is still
- * valid (as defined in omap3_power_states[]).
+ * valid.
+ *
+ * A state is valid if the 'valid' field is enabled and
+ * if it satisfies the enable_off_mode condition.
*/
static struct cpuidle_state *next_valid_state(struct cpuidle_device *dev,
- struct cpuidle_state *curr)
+ struct cpuidle_state *curr)
{
struct cpuidle_state *next = NULL;
- struct omap3_processor_cx *cx;
+ struct omap3_idle_statedata *cx = cpuidle_get_statedata(curr);
+ u32 mpu_deepest_state = PWRDM_POWER_RET;
+ u32 core_deepest_state = PWRDM_POWER_RET;
- cx = (struct omap3_processor_cx *)cpuidle_get_statedata(curr);
+ if (enable_off_mode) {
+ mpu_deepest_state = PWRDM_POWER_OFF;
+ /*
+ * Erratum i583: valable for ES rev < Es1.2 on 3630.
+ * CORE OFF mode is not supported in a stable form, restrict
+ * instead the CORE state to RET.
+ */
+ if (!IS_PM34XX_ERRATUM(PM_SDRC_WAKEUP_ERRATUM_i583))
+ core_deepest_state = PWRDM_POWER_OFF;
+ }
/* Check if current state is valid */
- if (cx->valid) {
+ if ((cx->valid) &&
+ (cx->mpu_state >= mpu_deepest_state) &&
+ (cx->core_state >= core_deepest_state)) {
return curr;
} else {
- u8 idx = OMAP3_STATE_MAX;
+ int idx = OMAP3_NUM_STATES - 1;
- /*
- * Reach the current state starting at highest C-state
- */
- for (; idx >= OMAP3_STATE_C1; idx--) {
+ /* Reach the current state starting at highest C-state */
+ for (; idx >= 0; idx--) {
if (&dev->states[idx] == curr) {
next = &dev->states[idx];
break;
}
}
- /*
- * Should never hit this condition.
- */
+ /* Should never hit this condition */
WARN_ON(next == NULL);
/*
* Start search from the next (lower) state.
*/
idx--;
- for (; idx >= OMAP3_STATE_C1; idx--) {
- struct omap3_processor_cx *cx;
-
+ for (; idx >= 0; idx--) {
cx = cpuidle_get_statedata(&dev->states[idx]);
- if (cx->valid) {
+ if ((cx->valid) &&
+ (cx->mpu_state >= mpu_deepest_state) &&
+ (cx->core_state >= core_deepest_state)) {
next = &dev->states[idx];
break;
}
}
/*
- * C1 and C2 are always valid.
+ * C1 is always valid.
* So, no need to check for 'next==NULL' outside this loop.
*/
}
* @dev: cpuidle device
* @state: The target state to be programmed
*
- * Used for C states with CPUIDLE_FLAG_CHECK_BM flag set. This
- * function checks for any pending activity and then programs the
- * device to the specified or a safer state.
+ * This function checks for any pending activity and then programs
+ * the device to the specified or a safer state.
*/
static int omap3_enter_idle_bm(struct cpuidle_device *dev,
struct cpuidle_state *state)
{
- struct cpuidle_state *new_state = next_valid_state(dev, state);
- u32 core_next_state, per_next_state = 0, per_saved_state = 0;
- u32 cam_state;
- struct omap3_processor_cx *cx;
+ struct cpuidle_state *new_state;
+ u32 core_next_state, per_next_state = 0, per_saved_state = 0, cam_state;
+ struct omap3_idle_statedata *cx;
int ret;
- if ((state->flags & CPUIDLE_FLAG_CHECK_BM) && omap3_idle_bm_check()) {
- BUG_ON(!dev->safe_state);
+ if (!omap3_can_sleep()) {
new_state = dev->safe_state;
goto select_state;
}
- cx = cpuidle_get_statedata(state);
- core_next_state = cx->core_state;
-
- /*
- * FIXME: we currently manage device-specific idle states
- * for PER and CORE in combination with CPU-specific
- * idle states. This is wrong, and device-specific
- * idle management needs to be separated out into
- * its own code.
- */
-
/*
* Prevent idle completely if CAM is active.
* CAM does not have wakeup capability in OMAP3.
goto select_state;
}
+ /*
+ * FIXME: we currently manage device-specific idle states
+ * for PER and CORE in combination with CPU-specific
+ * idle states. This is wrong, and device-specific
+ * idle management needs to be separated out into
+ * its own code.
+ */
+
/*
* Prevent PER off if CORE is not in retention or off as this
* would disable PER wakeups completely.
*/
+ cx = cpuidle_get_statedata(state);
+ core_next_state = cx->core_state;
per_next_state = per_saved_state = pwrdm_read_next_pwrst(per_pd);
if ((per_next_state == PWRDM_POWER_OFF) &&
(core_next_state > PWRDM_POWER_RET))
if (per_next_state != per_saved_state)
pwrdm_set_next_pwrst(per_pd, per_next_state);
+ new_state = next_valid_state(dev, state);
+
select_state:
dev->last_state = new_state;
ret = omap3_enter_idle(dev, new_state);
DEFINE_PER_CPU(struct cpuidle_device, omap3_idle_dev);
-/**
- * omap3_cpuidle_update_states() - Update the cpuidle states
- * @mpu_deepest_state: Enable states up to and including this for mpu domain
- * @core_deepest_state: Enable states up to and including this for core domain
- *
- * This goes through the list of states available and enables and disables the
- * validity of C states based on deepest state that can be achieved for the
- * variable domain
- */
-void omap3_cpuidle_update_states(u32 mpu_deepest_state, u32 core_deepest_state)
-{
- int i;
-
- for (i = OMAP3_STATE_C1; i < OMAP3_MAX_STATES; i++) {
- struct omap3_processor_cx *cx = &omap3_power_states[i];
-
- if ((cx->mpu_state >= mpu_deepest_state) &&
- (cx->core_state >= core_deepest_state)) {
- cx->valid = 1;
- } else {
- cx->valid = 0;
- }
- }
-}
-
void omap3_pm_init_cpuidle(struct cpuidle_params *cpuidle_board_params)
{
int i;
if (!cpuidle_board_params)
return;
- for (i = OMAP3_STATE_C1; i < OMAP3_MAX_STATES; i++) {
- cpuidle_params_table[i].valid =
- cpuidle_board_params[i].valid;
- cpuidle_params_table[i].sleep_latency =
- cpuidle_board_params[i].sleep_latency;
- cpuidle_params_table[i].wake_latency =
- cpuidle_board_params[i].wake_latency;
- cpuidle_params_table[i].threshold =
- cpuidle_board_params[i].threshold;
+ for (i = 0; i < OMAP3_NUM_STATES; i++) {
+ cpuidle_params_table[i].valid = cpuidle_board_params[i].valid;
+ cpuidle_params_table[i].exit_latency =
+ cpuidle_board_params[i].exit_latency;
+ cpuidle_params_table[i].target_residency =
+ cpuidle_board_params[i].target_residency;
}
return;
}
-/* omap3_init_power_states - Initialises the OMAP3 specific C states.
- *
- * Below is the desciption of each C state.
- * C1 . MPU WFI + Core active
- * C2 . MPU WFI + Core inactive
- * C3 . MPU CSWR + Core inactive
- * C4 . MPU OFF + Core inactive
- * C5 . MPU CSWR + Core CSWR
- * C6 . MPU OFF + Core CSWR
- * C7 . MPU OFF + Core OFF
- */
-void omap_init_power_states(void)
-{
- /* C1 . MPU WFI + Core active */
- omap3_power_states[OMAP3_STATE_C1].valid =
- cpuidle_params_table[OMAP3_STATE_C1].valid;
- omap3_power_states[OMAP3_STATE_C1].type = OMAP3_STATE_C1;
- omap3_power_states[OMAP3_STATE_C1].sleep_latency =
- cpuidle_params_table[OMAP3_STATE_C1].sleep_latency;
- omap3_power_states[OMAP3_STATE_C1].wakeup_latency =
- cpuidle_params_table[OMAP3_STATE_C1].wake_latency;
- omap3_power_states[OMAP3_STATE_C1].threshold =
- cpuidle_params_table[OMAP3_STATE_C1].threshold;
- omap3_power_states[OMAP3_STATE_C1].mpu_state = PWRDM_POWER_ON;
- omap3_power_states[OMAP3_STATE_C1].core_state = PWRDM_POWER_ON;
- omap3_power_states[OMAP3_STATE_C1].flags = CPUIDLE_FLAG_TIME_VALID;
- omap3_power_states[OMAP3_STATE_C1].desc = "MPU ON + CORE ON";
-
- /* C2 . MPU WFI + Core inactive */
- omap3_power_states[OMAP3_STATE_C2].valid =
- cpuidle_params_table[OMAP3_STATE_C2].valid;
- omap3_power_states[OMAP3_STATE_C2].type = OMAP3_STATE_C2;
- omap3_power_states[OMAP3_STATE_C2].sleep_latency =
- cpuidle_params_table[OMAP3_STATE_C2].sleep_latency;
- omap3_power_states[OMAP3_STATE_C2].wakeup_latency =
- cpuidle_params_table[OMAP3_STATE_C2].wake_latency;
- omap3_power_states[OMAP3_STATE_C2].threshold =
- cpuidle_params_table[OMAP3_STATE_C2].threshold;
- omap3_power_states[OMAP3_STATE_C2].mpu_state = PWRDM_POWER_ON;
- omap3_power_states[OMAP3_STATE_C2].core_state = PWRDM_POWER_ON;
- omap3_power_states[OMAP3_STATE_C2].flags = CPUIDLE_FLAG_TIME_VALID |
- CPUIDLE_FLAG_CHECK_BM;
- omap3_power_states[OMAP3_STATE_C2].desc = "MPU ON + CORE ON";
-
- /* C3 . MPU CSWR + Core inactive */
- omap3_power_states[OMAP3_STATE_C3].valid =
- cpuidle_params_table[OMAP3_STATE_C3].valid;
- omap3_power_states[OMAP3_STATE_C3].type = OMAP3_STATE_C3;
- omap3_power_states[OMAP3_STATE_C3].sleep_latency =
- cpuidle_params_table[OMAP3_STATE_C3].sleep_latency;
- omap3_power_states[OMAP3_STATE_C3].wakeup_latency =
- cpuidle_params_table[OMAP3_STATE_C3].wake_latency;
- omap3_power_states[OMAP3_STATE_C3].threshold =
- cpuidle_params_table[OMAP3_STATE_C3].threshold;
- omap3_power_states[OMAP3_STATE_C3].mpu_state = PWRDM_POWER_RET;
- omap3_power_states[OMAP3_STATE_C3].core_state = PWRDM_POWER_ON;
- omap3_power_states[OMAP3_STATE_C3].flags = CPUIDLE_FLAG_TIME_VALID |
- CPUIDLE_FLAG_CHECK_BM;
- omap3_power_states[OMAP3_STATE_C3].desc = "MPU RET + CORE ON";
-
- /* C4 . MPU OFF + Core inactive */
- omap3_power_states[OMAP3_STATE_C4].valid =
- cpuidle_params_table[OMAP3_STATE_C4].valid;
- omap3_power_states[OMAP3_STATE_C4].type = OMAP3_STATE_C4;
- omap3_power_states[OMAP3_STATE_C4].sleep_latency =
- cpuidle_params_table[OMAP3_STATE_C4].sleep_latency;
- omap3_power_states[OMAP3_STATE_C4].wakeup_latency =
- cpuidle_params_table[OMAP3_STATE_C4].wake_latency;
- omap3_power_states[OMAP3_STATE_C4].threshold =
- cpuidle_params_table[OMAP3_STATE_C4].threshold;
- omap3_power_states[OMAP3_STATE_C4].mpu_state = PWRDM_POWER_OFF;
- omap3_power_states[OMAP3_STATE_C4].core_state = PWRDM_POWER_ON;
- omap3_power_states[OMAP3_STATE_C4].flags = CPUIDLE_FLAG_TIME_VALID |
- CPUIDLE_FLAG_CHECK_BM;
- omap3_power_states[OMAP3_STATE_C4].desc = "MPU OFF + CORE ON";
-
- /* C5 . MPU CSWR + Core CSWR*/
- omap3_power_states[OMAP3_STATE_C5].valid =
- cpuidle_params_table[OMAP3_STATE_C5].valid;
- omap3_power_states[OMAP3_STATE_C5].type = OMAP3_STATE_C5;
- omap3_power_states[OMAP3_STATE_C5].sleep_latency =
- cpuidle_params_table[OMAP3_STATE_C5].sleep_latency;
- omap3_power_states[OMAP3_STATE_C5].wakeup_latency =
- cpuidle_params_table[OMAP3_STATE_C5].wake_latency;
- omap3_power_states[OMAP3_STATE_C5].threshold =
- cpuidle_params_table[OMAP3_STATE_C5].threshold;
- omap3_power_states[OMAP3_STATE_C5].mpu_state = PWRDM_POWER_RET;
- omap3_power_states[OMAP3_STATE_C5].core_state = PWRDM_POWER_RET;
- omap3_power_states[OMAP3_STATE_C5].flags = CPUIDLE_FLAG_TIME_VALID |
- CPUIDLE_FLAG_CHECK_BM;
- omap3_power_states[OMAP3_STATE_C5].desc = "MPU RET + CORE RET";
-
- /* C6 . MPU OFF + Core CSWR */
- omap3_power_states[OMAP3_STATE_C6].valid =
- cpuidle_params_table[OMAP3_STATE_C6].valid;
- omap3_power_states[OMAP3_STATE_C6].type = OMAP3_STATE_C6;
- omap3_power_states[OMAP3_STATE_C6].sleep_latency =
- cpuidle_params_table[OMAP3_STATE_C6].sleep_latency;
- omap3_power_states[OMAP3_STATE_C6].wakeup_latency =
- cpuidle_params_table[OMAP3_STATE_C6].wake_latency;
- omap3_power_states[OMAP3_STATE_C6].threshold =
- cpuidle_params_table[OMAP3_STATE_C6].threshold;
- omap3_power_states[OMAP3_STATE_C6].mpu_state = PWRDM_POWER_OFF;
- omap3_power_states[OMAP3_STATE_C6].core_state = PWRDM_POWER_RET;
- omap3_power_states[OMAP3_STATE_C6].flags = CPUIDLE_FLAG_TIME_VALID |
- CPUIDLE_FLAG_CHECK_BM;
- omap3_power_states[OMAP3_STATE_C6].desc = "MPU OFF + CORE RET";
-
- /* C7 . MPU OFF + Core OFF */
- omap3_power_states[OMAP3_STATE_C7].valid =
- cpuidle_params_table[OMAP3_STATE_C7].valid;
- omap3_power_states[OMAP3_STATE_C7].type = OMAP3_STATE_C7;
- omap3_power_states[OMAP3_STATE_C7].sleep_latency =
- cpuidle_params_table[OMAP3_STATE_C7].sleep_latency;
- omap3_power_states[OMAP3_STATE_C7].wakeup_latency =
- cpuidle_params_table[OMAP3_STATE_C7].wake_latency;
- omap3_power_states[OMAP3_STATE_C7].threshold =
- cpuidle_params_table[OMAP3_STATE_C7].threshold;
- omap3_power_states[OMAP3_STATE_C7].mpu_state = PWRDM_POWER_OFF;
- omap3_power_states[OMAP3_STATE_C7].core_state = PWRDM_POWER_OFF;
- omap3_power_states[OMAP3_STATE_C7].flags = CPUIDLE_FLAG_TIME_VALID |
- CPUIDLE_FLAG_CHECK_BM;
- omap3_power_states[OMAP3_STATE_C7].desc = "MPU OFF + CORE OFF";
-
- /*
- * Erratum i583: implementation for ES rev < Es1.2 on 3630. We cannot
- * enable OFF mode in a stable form for previous revisions.
- * we disable C7 state as a result.
- */
- if (IS_PM34XX_ERRATUM(PM_SDRC_WAKEUP_ERRATUM_i583)) {
- omap3_power_states[OMAP3_STATE_C7].valid = 0;
- cpuidle_params_table[OMAP3_STATE_C7].valid = 0;
- pr_warn("%s: core off state C7 disabled due to i583\n",
- __func__);
- }
-}
-
struct cpuidle_driver omap3_idle_driver = {
.name = "omap3_idle",
.owner = THIS_MODULE,
};
+/* Helper to fill the C-state common data and register the driver_data */
+static inline struct omap3_idle_statedata *_fill_cstate(
+ struct cpuidle_device *dev,
+ int idx, const char *descr)
+{
+ struct omap3_idle_statedata *cx = &omap3_idle_data[idx];
+ struct cpuidle_state *state = &dev->states[idx];
+
+ state->exit_latency = cpuidle_params_table[idx].exit_latency;
+ state->target_residency = cpuidle_params_table[idx].target_residency;
+ state->flags = CPUIDLE_FLAG_TIME_VALID;
+ state->enter = omap3_enter_idle_bm;
+ cx->valid = cpuidle_params_table[idx].valid;
+ sprintf(state->name, "C%d", idx + 1);
+ strncpy(state->desc, descr, CPUIDLE_DESC_LEN);
+ cpuidle_set_statedata(state, cx);
+
+ return cx;
+}
+
/**
* omap3_idle_init - Init routine for OMAP3 idle
*
- * Registers the OMAP3 specific cpuidle driver with the cpuidle
+ * Registers the OMAP3 specific cpuidle driver to the cpuidle
* framework with the valid set of states.
*/
int __init omap3_idle_init(void)
{
- int i, count = 0;
- struct omap3_processor_cx *cx;
- struct cpuidle_state *state;
struct cpuidle_device *dev;
+ struct omap3_idle_statedata *cx;
mpu_pd = pwrdm_lookup("mpu_pwrdm");
core_pd = pwrdm_lookup("core_pwrdm");
per_pd = pwrdm_lookup("per_pwrdm");
cam_pd = pwrdm_lookup("cam_pwrdm");
- omap_init_power_states();
cpuidle_register_driver(&omap3_idle_driver);
-
dev = &per_cpu(omap3_idle_dev, smp_processor_id());
- for (i = OMAP3_STATE_C1; i < OMAP3_MAX_STATES; i++) {
- cx = &omap3_power_states[i];
- state = &dev->states[count];
-
- if (!cx->valid)
- continue;
- cpuidle_set_statedata(state, cx);
- state->exit_latency = cx->sleep_latency + cx->wakeup_latency;
- state->target_residency = cx->threshold;
- state->flags = cx->flags;
- state->enter = (state->flags & CPUIDLE_FLAG_CHECK_BM) ?
- omap3_enter_idle_bm : omap3_enter_idle;
- if (cx->type == OMAP3_STATE_C1)
- dev->safe_state = state;
- sprintf(state->name, "C%d", count+1);
- strncpy(state->desc, cx->desc, CPUIDLE_DESC_LEN);
- count++;
- }
+ /* C1 . MPU WFI + Core active */
+ cx = _fill_cstate(dev, 0, "MPU ON + CORE ON");
+ (&dev->states[0])->enter = omap3_enter_idle;
+ dev->safe_state = &dev->states[0];
+ cx->valid = 1; /* C1 is always valid */
+ cx->mpu_state = PWRDM_POWER_ON;
+ cx->core_state = PWRDM_POWER_ON;
- if (!count)
- return -EINVAL;
- dev->state_count = count;
+ /* C2 . MPU WFI + Core inactive */
+ cx = _fill_cstate(dev, 1, "MPU ON + CORE ON");
+ cx->mpu_state = PWRDM_POWER_ON;
+ cx->core_state = PWRDM_POWER_ON;
+
+ /* C3 . MPU CSWR + Core inactive */
+ cx = _fill_cstate(dev, 2, "MPU RET + CORE ON");
+ cx->mpu_state = PWRDM_POWER_RET;
+ cx->core_state = PWRDM_POWER_ON;
- if (enable_off_mode)
- omap3_cpuidle_update_states(PWRDM_POWER_OFF, PWRDM_POWER_OFF);
- else
- omap3_cpuidle_update_states(PWRDM_POWER_RET, PWRDM_POWER_RET);
+ /* C4 . MPU OFF + Core inactive */
+ cx = _fill_cstate(dev, 3, "MPU OFF + CORE ON");
+ cx->mpu_state = PWRDM_POWER_OFF;
+ cx->core_state = PWRDM_POWER_ON;
+
+ /* C5 . MPU RET + Core RET */
+ cx = _fill_cstate(dev, 4, "MPU RET + CORE RET");
+ cx->mpu_state = PWRDM_POWER_RET;
+ cx->core_state = PWRDM_POWER_RET;
+
+ /* C6 . MPU OFF + Core RET */
+ cx = _fill_cstate(dev, 5, "MPU OFF + CORE RET");
+ cx->mpu_state = PWRDM_POWER_OFF;
+ cx->core_state = PWRDM_POWER_RET;
+
+ /* C7 . MPU OFF + Core OFF */
+ cx = _fill_cstate(dev, 6, "MPU OFF + CORE OFF");
+ /*
+ * Erratum i583: implementation for ES rev < Es1.2 on 3630. We cannot
+ * enable OFF mode in a stable form for previous revisions.
+ * We disable C7 state as a result.
+ */
+ if (IS_PM34XX_ERRATUM(PM_SDRC_WAKEUP_ERRATUM_i583)) {
+ cx->valid = 0;
+ pr_warn("%s: core off state C7 disabled due to i583\n",
+ __func__);
+ }
+ cx->mpu_state = PWRDM_POWER_OFF;
+ cx->core_state = PWRDM_POWER_OFF;
+ dev->state_count = OMAP3_NUM_STATES;
if (cpuidle_register_device(dev)) {
printk(KERN_ERR "%s: CPUidle register device failed\n",
__func__);
goto free1;
}
- if (gpio_request(gpmc_cfg->gpio_irq, "SMC91X irq") < 0)
+ if (gpio_request_one(gpmc_cfg->gpio_irq, GPIOF_IN, "SMC91X irq") < 0)
goto free1;
- gpio_direction_input(gpmc_cfg->gpio_irq);
gpmc_smc91x_resources[1].start = gpio_to_irq(gpmc_cfg->gpio_irq);
if (gpmc_cfg->gpio_pwrdwn) {
- ret = gpio_request(gpmc_cfg->gpio_pwrdwn, "SMC91X powerdown");
+ ret = gpio_request_one(gpmc_cfg->gpio_pwrdwn,
+ GPIOF_OUT_INIT_LOW, "SMC91X powerdown");
if (ret)
goto free2;
- gpio_direction_output(gpmc_cfg->gpio_pwrdwn, 0);
}
if (gpmc_cfg->gpio_reset) {
- ret = gpio_request(gpmc_cfg->gpio_reset, "SMC91X reset");
+ ret = gpio_request_one(gpmc_cfg->gpio_reset,
+ GPIOF_OUT_INIT_LOW, "SMC91X reset");
if (ret)
goto free3;
- gpio_direction_output(gpmc_cfg->gpio_reset, 0);
gpio_set_value(gpmc_cfg->gpio_reset, 1);
msleep(100);
gpio_set_value(gpmc_cfg->gpio_reset, 0);
* it under the terms of the GNU General Public License version 2 as
* published by the Free Software Foundation.
*/
+#define pr_fmt(fmt) "%s: " fmt, __func__
#include <linux/kernel.h>
#include <linux/platform_device.h>
.flags = IORESOURCE_MEM,
},
[1] = {
- .flags = IORESOURCE_IRQ,
+ .flags = IORESOURCE_IRQ | IORESOURCE_IRQ_LOWLEVEL,
},
};
.flags = SMSC911X_USE_16BIT,
};
-static struct platform_device gpmc_smsc911x_device = {
- .name = "smsc911x",
- .id = -1,
- .num_resources = ARRAY_SIZE(gpmc_smsc911x_resources),
- .resource = gpmc_smsc911x_resources,
- .dev = {
- .platform_data = &gpmc_smsc911x_config,
- },
-};
-
/*
* Initialize smsc911x device connected to the GPMC. Note that we
* assume that pin multiplexing is done in the board-*.c file,
*/
void __init gpmc_smsc911x_init(struct omap_smsc911x_platform_data *board_data)
{
+ struct platform_device *pdev;
unsigned long cs_mem_base;
int ret;
gpmc_cfg = board_data;
if (gpmc_cs_request(gpmc_cfg->cs, SZ_16M, &cs_mem_base) < 0) {
- printk(KERN_ERR "Failed to request GPMC mem for smsc911x\n");
+ pr_err("Failed to request GPMC mem region\n");
return;
}
gpmc_smsc911x_resources[0].start = cs_mem_base + 0x0;
gpmc_smsc911x_resources[0].end = cs_mem_base + 0xff;
- if (gpio_request(gpmc_cfg->gpio_irq, "smsc911x irq") < 0) {
- printk(KERN_ERR "Failed to request GPIO%d for smsc911x IRQ\n",
- gpmc_cfg->gpio_irq);
+ if (gpio_request_one(gpmc_cfg->gpio_irq, GPIOF_IN, "smsc911x irq")) {
+ pr_err("Failed to request IRQ GPIO%d\n", gpmc_cfg->gpio_irq);
goto free1;
}
- gpio_direction_input(gpmc_cfg->gpio_irq);
gpmc_smsc911x_resources[1].start = gpio_to_irq(gpmc_cfg->gpio_irq);
- gpmc_smsc911x_resources[1].flags |=
- (gpmc_cfg->flags & IRQF_TRIGGER_MASK);
if (gpio_is_valid(gpmc_cfg->gpio_reset)) {
- ret = gpio_request(gpmc_cfg->gpio_reset, "smsc911x reset");
+ ret = gpio_request_one(gpmc_cfg->gpio_reset,
+ GPIOF_OUT_INIT_HIGH, "smsc911x reset");
if (ret) {
- printk(KERN_ERR "Failed to request GPIO%d for smsc911x reset\n",
- gpmc_cfg->gpio_reset);
+ pr_err("Failed to request reset GPIO%d\n",
+ gpmc_cfg->gpio_reset);
goto free2;
}
- gpio_direction_output(gpmc_cfg->gpio_reset, 1);
gpio_set_value(gpmc_cfg->gpio_reset, 0);
msleep(100);
gpio_set_value(gpmc_cfg->gpio_reset, 1);
}
- if (platform_device_register(&gpmc_smsc911x_device) < 0) {
- printk(KERN_ERR "Unable to register smsc911x device\n");
+ if (gpmc_cfg->flags)
+ gpmc_smsc911x_config.flags = gpmc_cfg->flags;
+
+ pdev = platform_device_register_resndata(NULL, "smsc911x", gpmc_cfg->id,
+ gpmc_smsc911x_resources, ARRAY_SIZE(gpmc_smsc911x_resources),
+ &gpmc_smsc911x_config, sizeof(gpmc_smsc911x_config));
+ if (!pdev) {
+ pr_err("Unable to register platform device\n");
gpio_free(gpmc_cfg->gpio_reset);
goto free2;
}
free1:
gpmc_cs_free(gpmc_cfg->cs);
- printk(KERN_ERR "Could not initialize smsc911x\n");
+ pr_err("Could not initialize smsc911x device\n");
}
char *source_name;
/* Get the Type of interrupt */
- if (irq == l3->app_irq)
- inttype = L3_APPLICATION_ERROR;
- else
- inttype = L3_DEBUG_ERROR;
+ inttype = irq == l3->app_irq ? L3_APPLICATION_ERROR : L3_DEBUG_ERROR;
for (i = 0; i < L3_MODULES; i++) {
/*
err_src = j;
/* Read the stderrlog_main_source from clk domain */
- std_err_main_addr = base + (*(l3_targ[i] + err_src));
- std_err_main = readl(std_err_main_addr);
+ std_err_main_addr = base + *(l3_targ[i] + err_src);
+ std_err_main = readl(std_err_main_addr);
- switch ((std_err_main & CUSTOM_ERROR)) {
+ switch (std_err_main & CUSTOM_ERROR) {
case STANDARD_ERROR:
source_name =
l3_targ_stderrlog_main_name[i][err_src];
l3 = kzalloc(sizeof(*l3), GFP_KERNEL);
if (!l3)
- ret = -ENOMEM;
+ return -ENOMEM;
platform_set_drvdata(pdev, l3);
res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
if (!res) {
dev_err(&pdev->dev, "couldn't find resource 0\n");
ret = -ENODEV;
- goto err1;
+ goto err0;
}
l3->l3_base[0] = ioremap(res->start, resource_size(res));
- if (!(l3->l3_base[0])) {
+ if (!l3->l3_base[0]) {
dev_err(&pdev->dev, "ioremap failed\n");
ret = -ENOMEM;
- goto err2;
+ goto err0;
}
res = platform_get_resource(pdev, IORESOURCE_MEM, 1);
if (!res) {
dev_err(&pdev->dev, "couldn't find resource 1\n");
ret = -ENODEV;
- goto err3;
+ goto err1;
}
l3->l3_base[1] = ioremap(res->start, resource_size(res));
- if (!(l3->l3_base[1])) {
+ if (!l3->l3_base[1]) {
dev_err(&pdev->dev, "ioremap failed\n");
ret = -ENOMEM;
- goto err4;
+ goto err1;
}
res = platform_get_resource(pdev, IORESOURCE_MEM, 2);
if (!res) {
dev_err(&pdev->dev, "couldn't find resource 2\n");
ret = -ENODEV;
- goto err5;
+ goto err2;
}
l3->l3_base[2] = ioremap(res->start, resource_size(res));
- if (!(l3->l3_base[2])) {
+ if (!l3->l3_base[2]) {
dev_err(&pdev->dev, "ioremap failed\n");
ret = -ENOMEM;
- goto err6;
+ goto err2;
}
/*
if (ret) {
pr_crit("L3: request_irq failed to register for 0x%x\n",
OMAP44XX_IRQ_L3_DBG);
- goto err7;
+ goto err3;
}
l3->debug_irq = irq;
if (ret) {
pr_crit("L3: request_irq failed to register for 0x%x\n",
OMAP44XX_IRQ_L3_APP);
- goto err8;
+ goto err4;
}
l3->app_irq = irq;
- goto err0;
-err8:
-err7:
- iounmap(l3->l3_base[2]);
-err6:
-err5:
- iounmap(l3->l3_base[1]);
+ return 0;
+
err4:
+ free_irq(l3->debug_irq, l3);
err3:
- iounmap(l3->l3_base[0]);
+ iounmap(l3->l3_base[2]);
err2:
+ iounmap(l3->l3_base[1]);
err1:
- kfree(l3);
+ iounmap(l3->l3_base[0]);
err0:
+ kfree(l3);
return ret;
}
u8 multi = error & L3_ERROR_LOG_MULTI;
u32 address = omap3_l3_decode_addr(error_addr);
- WARN(true, "%s Error seen by %s %s at address %x\n",
+ WARN(true, "%s seen by %s %s at address %x\n",
omap3_l3_code_string(code),
omap3_l3_initiator_string(initid),
multi ? "Multiple Errors" : "",
static irqreturn_t omap3_l3_app_irq(int irq, void *_l3)
{
struct omap3_l3 *l3 = _l3;
-
u64 status, clear;
u64 error;
u64 error_addr;
u64 err_source = 0;
void __iomem *base;
int int_type;
-
irqreturn_t ret = IRQ_NONE;
- if (irq == l3->app_irq)
- int_type = L3_APPLICATION_ERROR;
- else
- int_type = L3_DEBUG_ERROR;
-
+ int_type = irq == l3->app_irq ? L3_APPLICATION_ERROR : L3_DEBUG_ERROR;
if (!int_type) {
status = omap3_l3_readll(l3->rt, L3_SI_FLAG_STATUS_0);
/*
base = l3->rt + *(omap3_l3_bases[int_type] + err_source);
error = omap3_l3_readll(base, L3_ERROR_LOG);
-
if (error) {
error_addr = omap3_l3_readll(base, L3_ERROR_LOG_ADDR);
}
/* Clear the status register */
- clear = ((L3_AGENT_STATUS_CLEAR_IA << int_type) |
- (L3_AGENT_STATUS_CLEAR_TA));
-
+ clear = (L3_AGENT_STATUS_CLEAR_IA << int_type) |
+ L3_AGENT_STATUS_CLEAR_TA;
omap3_l3_writell(base, L3_AGENT_STATUS, clear);
/* clear the error log register */
int ret;
l3 = kzalloc(sizeof(*l3), GFP_KERNEL);
- if (!l3) {
- ret = -ENOMEM;
- goto err0;
- }
+ if (!l3)
+ return -ENOMEM;
platform_set_drvdata(pdev, l3);
if (!res) {
dev_err(&pdev->dev, "couldn't find resource\n");
ret = -ENODEV;
- goto err1;
+ goto err0;
}
l3->rt = ioremap(res->start, resource_size(res));
- if (!(l3->rt)) {
+ if (!l3->rt) {
dev_err(&pdev->dev, "ioremap failed\n");
ret = -ENOMEM;
- goto err2;
+ goto err0;
}
l3->debug_irq = platform_get_irq(pdev, 0);
"l3-debug-irq", l3);
if (ret) {
dev_err(&pdev->dev, "couldn't request debug irq\n");
- goto err3;
+ goto err1;
}
l3->app_irq = platform_get_irq(pdev, 1);
ret = request_irq(l3->app_irq, omap3_l3_app_irq,
IRQF_DISABLED | IRQF_TRIGGER_RISING,
"l3-app-irq", l3);
-
if (ret) {
dev_err(&pdev->dev, "couldn't request app irq\n");
- goto err4;
+ goto err2;
}
- goto err0;
+ return 0;
-err4:
-err3:
- iounmap(l3->rt);
err2:
+ free_irq(l3->debug_irq, l3);
err1:
- kfree(l3);
+ iounmap(l3->rt);
err0:
+ kfree(l3);
return ret;
}
{
ctrl_base = ioremap(OMAP443X_SCM_BASE, SZ_1K);
if (!ctrl_base) {
- dev_err(dev, "control module ioremap failed\n");
+ pr_err("control module ioremap failed\n");
return -ENOMEM;
}
/* Power down the phy */
__raw_writel(PHY_PD, ctrl_base + CONTROL_DEV_CONF);
- phyclk = clk_get(dev, "ocp2scp_usb_phy_ick");
+ if (!dev)
+ return 0;
+
+ phyclk = clk_get(dev, "ocp2scp_usb_phy_ick");
if (IS_ERR(phyclk)) {
dev_err(dev, "cannot clk_get ocp2scp_usb_phy_ick\n");
iounmap(ctrl_base);
regval = omap_ctrl_readl(AM35XX_CONTROL_LVL_INTR_CLEAR);
}
-void am35x_musb_set_mode(u8 musb_mode)
+void am35x_set_mode(u8 musb_mode)
{
u32 devconf2 = omap_ctrl_readl(AM35XX_CONTROL_DEVCONF2);
}
#endif
+/*
+ * cpuidle mach specific parameters
+ *
+ * The board code can override the default C-states definition using
+ * omap3_pm_init_cpuidle
+ */
struct cpuidle_params {
- u8 valid;
- u32 sleep_latency;
- u32 wake_latency;
- u32 threshold;
+ u32 exit_latency; /* exit_latency = sleep + wake-up latencies */
+ u32 target_residency;
+ u8 valid; /* validates the C-state */
};
#if defined(CONFIG_PM) && defined(CONFIG_CPU_IDLE)
#define sleep_while_idle 0
#endif
-#if defined(CONFIG_CPU_IDLE)
-extern void omap3_cpuidle_update_states(u32, u32);
-#endif
-
#if defined(CONFIG_PM_DEBUG) && defined(CONFIG_DEBUG_FS)
extern void pm_dbg_update_time(struct powerdomain *pwrdm, int prev);
extern int pm_dbg_regset_save(int reg_set);
else
state = PWRDM_POWER_RET;
-#ifdef CONFIG_CPU_IDLE
- /*
- * Erratum i583: implementation for ES rev < Es1.2 on 3630. We cannot
- * enable OFF mode in a stable form for previous revisions, restrict
- * instead to RET
- */
- if (IS_PM34XX_ERRATUM(PM_SDRC_WAKEUP_ERRATUM_i583))
- omap3_cpuidle_update_states(state, PWRDM_POWER_RET);
- else
- omap3_cpuidle_update_states(state, state);
-#endif
-
list_for_each_entry(pwrst, &pwrst_list, node) {
if (IS_PM34XX_ERRATUM(PM_SDRC_WAKEUP_ERRATUM_i583) &&
pwrst->pwrdm == core_pwrdm &&
pm_errata_configure();
- printk(KERN_ERR "Power Management for TI OMAP3.\n");
-
/* XXX prcm_setup_regs needs to be before enabling hw
* supervised mode for powerdomains */
prcm_setup_regs();
pr_err("Power Management for TI OMAP4.\n");
-#ifdef CONFIG_PM
ret = pwrdm_for_each(pwrdms_setup, NULL);
if (ret) {
pr_err("Failed to setup powerdomains\n");
goto err2;
}
-#endif
#ifdef CONFIG_SUSPEND
suspend_set_ops(&omap_pm_ops);
goto err_free_devinfo;
}
+ mem = request_mem_region(mem->start, resource_size(mem),
+ dev_name(&pdev->dev));
+ if (!mem) {
+ dev_err(&pdev->dev, "%s: no mem region\n", __func__);
+ ret = -EBUSY;
+ goto err_free_devinfo;
+ }
+
irq = platform_get_resource(pdev, IORESOURCE_IRQ, 0);
pm_runtime_enable(&pdev->dev);
ret = sr_late_init(sr_info);
if (ret) {
pr_warning("%s: Error in SR late init\n", __func__);
- goto err_release_region;
+ return ret;
}
}
vdd_dbg_dir = omap_voltage_get_dbgdir(sr_info->voltdm);
if (!vdd_dbg_dir) {
ret = -EINVAL;
- goto err_release_region;
+ goto err_iounmap;
}
sr_info->dbg_dir = debugfs_create_dir("smartreflex", vdd_dbg_dir);
dev_err(&pdev->dev, "%s: Unable to create debugfs directory\n",
__func__);
ret = PTR_ERR(sr_info->dbg_dir);
- goto err_release_region;
+ goto err_iounmap;
}
(void) debugfs_create_file("autocomp", S_IRUGO | S_IWUSR,
dev_err(&pdev->dev, "%s: Unable to create debugfs directory"
"for n-values\n", __func__);
ret = PTR_ERR(nvalue_dir);
- goto err_release_region;
+ goto err_debugfs;
}
omap_voltage_get_volttable(sr_info->voltdm, &volt_data);
"entries for n-values\n",
__func__, sr_info->voltdm->name);
ret = -ENODATA;
- goto err_release_region;
+ goto err_debugfs;
}
for (i = 0; i < sr_info->nvalue_count; i++) {
return ret;
+err_debugfs:
+ debugfs_remove_recursive(sr_info->dbg_dir);
+err_iounmap:
+ list_del(&sr_info->node);
+ iounmap(sr_info->base);
err_release_region:
release_mem_region(mem->start, resource_size(mem));
err_free_devinfo:
}
}
-void __init usb_musb_init(struct omap_musb_board_data *board_data)
+static struct omap_musb_board_data musb_default_board_data = {
+ .interface_type = MUSB_INTERFACE_ULPI,
+ .mode = MUSB_OTG,
+ .power = 100,
+};
+
+void __init usb_musb_init(struct omap_musb_board_data *musb_board_data)
{
struct omap_hwmod *oh;
struct omap_device *od;
struct device *dev;
int bus_id = -1;
const char *oh_name, *name;
+ struct omap_musb_board_data *board_data;
- if (cpu_is_omap3517() || cpu_is_omap3505()) {
- } else if (cpu_is_omap44xx()) {
- usb_musb_mux_init(board_data);
- }
+ if (musb_board_data)
+ board_data = musb_board_data;
+ else
+ board_data = &musb_default_board_data;
/*
* REVISIT: This line can be removed once all the platforms using
dev->dma_mask = &musb_dmamask;
dev->coherent_dma_mask = musb_dmamask;
put_device(dev);
+
+ if (cpu_is_omap44xx())
+ omap4430_phy_init(dev);
}
#else
void __init usb_musb_init(struct omap_musb_board_data *board_data)
{
+ if (cpu_is_omap44xx())
+ omap4430_phy_init(NULL);
}
#endif /* CONFIG_USB_MUSB_SOC */
);
/* IRQ */
- status = gpio_request(irq, "TUSB6010 irq");
+ status = gpio_request_one(irq, GPIOF_IN, "TUSB6010 irq");
if (status < 0) {
printk(error, 3, status);
return status;
}
- gpio_direction_input(irq);
tusb_resources[2].start = irq + IH_GPIO_BASE;
/* set up memory timings ... can speed them up later */
}
vsel = vdd->read_reg(prm_mod_offs, vdd->vp_data->voltage);
- pr_notice("curr_vsel = %x\n", vsel);
if (!vdd->pmic_info->vsel_to_uv) {
pr_warning("PMIC function to convert vsel to voltage"
#ifndef __ASM_ARCH_OMAP_GPMC_SMSC911X_H__
struct omap_smsc911x_platform_data {
+ int id;
int cs;
int gpio_irq;
int gpio_reset;
u32 flags;
};
-#if defined(CONFIG_SMSC911X) || \
- defined(CONFIG_SMSC911X_MODULE)
+#if defined(CONFIG_SMSC911X) || defined(CONFIG_SMSC911X_MODULE)
extern void gpmc_smsc911x_init(struct omap_smsc911x_platform_data *d);
DEBUG_LL_OMAP1(3, sx1);
/* omap2 based boards using UART1 */
- DEBUG_LL_OMAP2(1, omap2evm);
DEBUG_LL_OMAP2(1, omap_2430sdp);
DEBUG_LL_OMAP2(1, omap_apollon);
DEBUG_LL_OMAP2(1, omap_h4);
extern void am35x_musb_reset(void);
extern void am35x_musb_phy_power(u8 on);
extern void am35x_musb_clear_irq(void);
-extern void am35x_musb_set_mode(u8 musb_mode);
+extern void am35x_set_mode(u8 musb_mode);
/*
* FIXME correct answer depends on hmc_mode,
objs-y$(CONFIG_MACH_OMAP_2430SDP) += lcd_2430sdp.o
objs-y$(CONFIG_MACH_OMAP_3430SDP) += lcd_2430sdp.o
objs-y$(CONFIG_MACH_OMAP_LDP) += lcd_ldp.o
-objs-y$(CONFIG_MACH_OMAP2EVM) += lcd_omap2evm.o
objs-y$(CONFIG_MACH_OMAP3EVM) += lcd_omap3evm.o
objs-y$(CONFIG_MACH_OMAP3_BEAGLE) += lcd_omap3beagle.o
objs-y$(CONFIG_FB_OMAP_LCD_MIPID) += lcd_mipid.o
+++ /dev/null
-/*
- * LCD panel support for the MISTRAL OMAP2EVM board
- *
- * Author: Arun C <arunedarath@mistralsolutions.com>
- *
- * Derived from drivers/video/omap/lcd_omap3evm.c
- * Derived from drivers/video/omap/lcd-apollon.c
- *
- * This program is free software; you can redistribute it and/or modify it
- * under the terms of the GNU General Public License as published by the
- * Free Software Foundation; either version 2 of the License, or (at your
- * option) any later version.
- *
- * This program is distributed in the hope that it will be useful, but
- * WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU
- * General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License along
- * with this program; if not, write to the Free Software Foundation, Inc.,
- * 59 Temple Place - Suite 330, Boston, MA 02111-1307, USA.
- */
-
-#include <linux/module.h>
-#include <linux/platform_device.h>
-#include <linux/gpio.h>
-#include <linux/i2c/twl.h>
-
-#include <plat/mux.h>
-#include <asm/mach-types.h>
-
-#include "omapfb.h"
-
-#define LCD_PANEL_ENABLE_GPIO 154
-#define LCD_PANEL_LR 128
-#define LCD_PANEL_UD 129
-#define LCD_PANEL_INI 152
-#define LCD_PANEL_QVGA 148
-#define LCD_PANEL_RESB 153
-
-#define TWL_LED_LEDEN 0x00
-#define TWL_PWMA_PWMAON 0x00
-#define TWL_PWMA_PWMAOFF 0x01
-
-static unsigned int bklight_level;
-
-static int omap2evm_panel_init(struct lcd_panel *panel,
- struct omapfb_device *fbdev)
-{
- gpio_request(LCD_PANEL_ENABLE_GPIO, "LCD enable");
- gpio_request(LCD_PANEL_LR, "LCD lr");
- gpio_request(LCD_PANEL_UD, "LCD ud");
- gpio_request(LCD_PANEL_INI, "LCD ini");
- gpio_request(LCD_PANEL_QVGA, "LCD qvga");
- gpio_request(LCD_PANEL_RESB, "LCD resb");
-
- gpio_direction_output(LCD_PANEL_ENABLE_GPIO, 1);
- gpio_direction_output(LCD_PANEL_RESB, 1);
- gpio_direction_output(LCD_PANEL_INI, 1);
- gpio_direction_output(LCD_PANEL_QVGA, 0);
- gpio_direction_output(LCD_PANEL_LR, 1);
- gpio_direction_output(LCD_PANEL_UD, 1);
-
- twl_i2c_write_u8(TWL4030_MODULE_LED, 0x11, TWL_LED_LEDEN);
- twl_i2c_write_u8(TWL4030_MODULE_PWMA, 0x01, TWL_PWMA_PWMAON);
- twl_i2c_write_u8(TWL4030_MODULE_PWMA, 0x02, TWL_PWMA_PWMAOFF);
- bklight_level = 100;
-
- return 0;
-}
-
-static void omap2evm_panel_cleanup(struct lcd_panel *panel)
-{
- gpio_free(LCD_PANEL_RESB);
- gpio_free(LCD_PANEL_QVGA);
- gpio_free(LCD_PANEL_INI);
- gpio_free(LCD_PANEL_UD);
- gpio_free(LCD_PANEL_LR);
- gpio_free(LCD_PANEL_ENABLE_GPIO);
-}
-
-static int omap2evm_panel_enable(struct lcd_panel *panel)
-{
- gpio_set_value(LCD_PANEL_ENABLE_GPIO, 0);
- return 0;
-}
-
-static void omap2evm_panel_disable(struct lcd_panel *panel)
-{
- gpio_set_value(LCD_PANEL_ENABLE_GPIO, 1);
-}
-
-static unsigned long omap2evm_panel_get_caps(struct lcd_panel *panel)
-{
- return 0;
-}
-
-static int omap2evm_bklight_setlevel(struct lcd_panel *panel,
- unsigned int level)
-{
- u8 c;
- if ((level >= 0) && (level <= 100)) {
- c = (125 * (100 - level)) / 100 + 2;
- twl_i2c_write_u8(TWL4030_MODULE_PWMA, c, TWL_PWMA_PWMAOFF);
- bklight_level = level;
- }
- return 0;
-}
-
-static unsigned int omap2evm_bklight_getlevel(struct lcd_panel *panel)
-{
- return bklight_level;
-}
-
-static unsigned int omap2evm_bklight_getmaxlevel(struct lcd_panel *panel)
-{
- return 100;
-}
-
-struct lcd_panel omap2evm_panel = {
- .name = "omap2evm",
- .config = OMAP_LCDC_PANEL_TFT | OMAP_LCDC_INV_VSYNC |
- OMAP_LCDC_INV_HSYNC,
-
- .bpp = 16,
- .data_lines = 18,
- .x_res = 480,
- .y_res = 640,
- .hsw = 3,
- .hfp = 0,
- .hbp = 28,
- .vsw = 2,
- .vfp = 1,
- .vbp = 0,
-
- .pixel_clock = 20000,
-
- .init = omap2evm_panel_init,
- .cleanup = omap2evm_panel_cleanup,
- .enable = omap2evm_panel_enable,
- .disable = omap2evm_panel_disable,
- .get_caps = omap2evm_panel_get_caps,
- .set_bklight_level = omap2evm_bklight_setlevel,
- .get_bklight_level = omap2evm_bklight_getlevel,
- .get_bklight_max = omap2evm_bklight_getmaxlevel,
-};
-
-static int omap2evm_panel_probe(struct platform_device *pdev)
-{
- omapfb_register_panel(&omap2evm_panel);
- return 0;
-}
-
-static int omap2evm_panel_remove(struct platform_device *pdev)
-{
- return 0;
-}
-
-static int omap2evm_panel_suspend(struct platform_device *pdev,
- pm_message_t mesg)
-{
- return 0;
-}
-
-static int omap2evm_panel_resume(struct platform_device *pdev)
-{
- return 0;
-}
-
-struct platform_driver omap2evm_panel_driver = {
- .probe = omap2evm_panel_probe,
- .remove = omap2evm_panel_remove,
- .suspend = omap2evm_panel_suspend,
- .resume = omap2evm_panel_resume,
- .driver = {
- .name = "omap2evm_lcd",
- .owner = THIS_MODULE,
- },
-};
-
-static int __init omap2evm_panel_drv_init(void)
-{
- return platform_driver_register(&omap2evm_panel_driver);
-}
-
-static void __exit omap2evm_panel_drv_exit(void)
-{
- platform_driver_unregister(&omap2evm_panel_driver);
-}
-
-module_init(omap2evm_panel_drv_init);
-module_exit(omap2evm_panel_drv_exit);
Say Y if you want to add support for SoC audio on the
Gumstix Overo or CompuLab CM-T35
-config SND_OMAP_SOC_OMAP2EVM
- tristate "SoC Audio support for OMAP2EVM board"
- depends on TWL4030_CORE && SND_OMAP_SOC && MACH_OMAP2EVM
- select SND_OMAP_SOC_MCBSP
- select SND_SOC_TWL4030
- help
- Say Y if you want to add support for SoC audio on the omap2evm board.
-
config SND_OMAP_SOC_OMAP3EVM
tristate "SoC Audio support for OMAP3EVM board"
depends on TWL4030_CORE && SND_OMAP_SOC && MACH_OMAP3EVM
snd-soc-ams-delta-objs := ams-delta.o
snd-soc-osk5912-objs := osk5912.o
snd-soc-overo-objs := overo.o
-snd-soc-omap2evm-objs := omap2evm.o
snd-soc-omap3evm-objs := omap3evm.o
snd-soc-am3517evm-objs := am3517evm.o
snd-soc-sdp3430-objs := sdp3430.o
+++ /dev/null
-/*
- * omap2evm.c -- SoC audio machine driver for omap2evm board
- *
- * Author: Arun KS <arunks@mistralsolutions.com>
- *
- * Based on sound/soc/omap/overo.c by Steve Sakoman
- *
- * This program is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License
- * version 2 as published by the Free Software Foundation.
- *
- * This program is distributed in the hope that it will be useful, but
- * WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU
- * General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA
- * 02110-1301 USA
- *
- */
-
-#include <linux/clk.h>
-#include <linux/platform_device.h>
-#include <sound/core.h>
-#include <sound/pcm.h>
-#include <sound/soc.h>
-
-#include <asm/mach-types.h>
-#include <mach/hardware.h>
-#include <mach/gpio.h>
-#include <plat/mcbsp.h>
-
-#include "omap-mcbsp.h"
-#include "omap-pcm.h"
-
-static int omap2evm_hw_params(struct snd_pcm_substream *substream,
- struct snd_pcm_hw_params *params)
-{
- struct snd_soc_pcm_runtime *rtd = substream->private_data;
- struct snd_soc_dai *codec_dai = rtd->codec_dai;
- struct snd_soc_dai *cpu_dai = rtd->cpu_dai;
- int ret;
-
- /* Set codec DAI configuration */
- ret = snd_soc_dai_set_fmt(codec_dai,
- SND_SOC_DAIFMT_I2S |
- SND_SOC_DAIFMT_NB_NF |
- SND_SOC_DAIFMT_CBM_CFM);
- if (ret < 0) {
- printk(KERN_ERR "can't set codec DAI configuration\n");
- return ret;
- }
-
- /* Set cpu DAI configuration */
- ret = snd_soc_dai_set_fmt(cpu_dai,
- SND_SOC_DAIFMT_I2S |
- SND_SOC_DAIFMT_NB_NF |
- SND_SOC_DAIFMT_CBM_CFM);
- if (ret < 0) {
- printk(KERN_ERR "can't set cpu DAI configuration\n");
- return ret;
- }
-
- /* Set the codec system clock for DAC and ADC */
- ret = snd_soc_dai_set_sysclk(codec_dai, 0, 26000000,
- SND_SOC_CLOCK_IN);
- if (ret < 0) {
- printk(KERN_ERR "can't set codec system clock\n");
- return ret;
- }
-
- return 0;
-}
-
-static struct snd_soc_ops omap2evm_ops = {
- .hw_params = omap2evm_hw_params,
-};
-
-/* Digital audio interface glue - connects codec <--> CPU */
-static struct snd_soc_dai_link omap2evm_dai = {
- .name = "TWL4030",
- .stream_name = "TWL4030",
- .cpu_dai_name = "omap-mcbsp-dai.1",
- .codec_dai_name = "twl4030-hifi",
- .platform_name = "omap-pcm-audio",
- .codec_name = "twl4030-codec",
- .ops = &omap2evm_ops,
-};
-
-/* Audio machine driver */
-static struct snd_soc_card snd_soc_omap2evm = {
- .name = "omap2evm",
- .dai_link = &omap2evm_dai,
- .num_links = 1,
-};
-
-static struct platform_device *omap2evm_snd_device;
-
-static int __init omap2evm_soc_init(void)
-{
- int ret;
-
- if (!machine_is_omap2evm())
- return -ENODEV;
- printk(KERN_INFO "omap2evm SoC init\n");
-
- omap2evm_snd_device = platform_device_alloc("soc-audio", -1);
- if (!omap2evm_snd_device) {
- printk(KERN_ERR "Platform device allocation failed\n");
- return -ENOMEM;
- }
-
- platform_set_drvdata(omap2evm_snd_device, &snd_soc_omap2evm);
-
- ret = platform_device_add(omap2evm_snd_device);
- if (ret)
- goto err1;
-
- return 0;
-
-err1:
- printk(KERN_ERR "Unable to add platform device\n");
- platform_device_put(omap2evm_snd_device);
-
- return ret;
-}
-module_init(omap2evm_soc_init);
-
-static void __exit omap2evm_soc_exit(void)
-{
- platform_device_unregister(omap2evm_snd_device);
-}
-module_exit(omap2evm_soc_exit);
-
-MODULE_AUTHOR("Arun KS <arunks@mistralsolutions.com>");
-MODULE_DESCRIPTION("ALSA SoC omap2evm");
-MODULE_LICENSE("GPL");
git.openpandora.org / pandora-kernel.git / commitdiff