* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input: (75 commits)
Input: wacom - specify Cinitq supported tools
Input: ab8500-ponkey - fix IRQ freeing in error path
Input: adp5588-keys - use more obvious i2c_device_id name string
Input: ad7877 - switch to using threaded IRQ
Input: ad7877 - use attribute group to control visibility of attributes
Input: serio - add support for PS2Mult multiplexer protocol
Input: wacom - properly enable runtime PM
Input: ad7877 - filter events where pressure is beyond the maximum
Input: ad7877 - implement EV_KEY:BTN_TOUCH reporting
Input: ad7877 - implement specified chip select behavior
Input: hp680_ts_input - use cancel_delayed_work_sync()
Input: mousedev - correct lockdep annotation
Input: ads7846 - switch to using threaded IRQ
Input: serio - support multiple child devices per single parent
Input: synaptics - simplify pass-through port handling
Input: add ROHM BU21013 touch panel controller support
Input: omap4-keypad - wake-up on events & long presses
Input: omap4-keypad - fix interrupt line configuration
Input: omap4-keypad - SYSCONFIG register configuration
Input: omap4-keypad - use platform device helpers
...
#include <linux/amba/pl022.h>
#include <linux/spi/spi.h>
#include <linux/mfd/ab8500.h>
+#include <linux/input/matrix_keypad.h>
#include <asm/mach-types.h>
#include <asm/mach/arch.h>
#include <plat/pincfg.h>
#include <plat/i2c.h>
+#include <plat/ske.h>
#include <mach/hardware.h>
#include <mach/setup.h>
GPIO11_I2C2_SCL,
GPIO229_I2C3_SDA,
GPIO230_I2C3_SCL,
+
+ /* SKE keypad */
+ GPIO153_KP_I7,
+ GPIO154_KP_I6,
+ GPIO155_KP_I5,
+ GPIO156_KP_I4,
+ GPIO157_KP_O7,
+ GPIO158_KP_O6,
+ GPIO159_KP_O5,
+ GPIO160_KP_O4,
+ GPIO161_KP_I3,
+ GPIO162_KP_I2,
+ GPIO163_KP_I1,
+ GPIO164_KP_I0,
+ GPIO165_KP_O3,
+ GPIO166_KP_O2,
+ GPIO167_KP_O1,
+ GPIO168_KP_O0,
};
static void ab4500_spi_cs_control(u32 command)
&u8500_ssp0_device,
};
+static const unsigned int ux500_keymap[] = {
+ KEY(2, 5, KEY_END),
+ KEY(4, 1, KEY_POWER),
+ KEY(3, 5, KEY_VOLUMEDOWN),
+ KEY(1, 3, KEY_3),
+ KEY(5, 2, KEY_RIGHT),
+ KEY(5, 0, KEY_9),
+
+ KEY(0, 5, KEY_MENU),
+ KEY(7, 6, KEY_ENTER),
+ KEY(4, 5, KEY_0),
+ KEY(6, 7, KEY_2),
+ KEY(3, 4, KEY_UP),
+ KEY(3, 3, KEY_DOWN),
+
+ KEY(6, 4, KEY_SEND),
+ KEY(6, 2, KEY_BACK),
+ KEY(4, 2, KEY_VOLUMEUP),
+ KEY(5, 5, KEY_1),
+ KEY(4, 3, KEY_LEFT),
+ KEY(3, 2, KEY_7),
+};
+
+static const struct matrix_keymap_data ux500_keymap_data = {
+ .keymap = ux500_keymap,
+ .keymap_size = ARRAY_SIZE(ux500_keymap),
+};
+
+/*
+ * Nomadik SKE keypad
+ */
+#define ROW_PIN_I0 164
+#define ROW_PIN_I1 163
+#define ROW_PIN_I2 162
+#define ROW_PIN_I3 161
+#define ROW_PIN_I4 156
+#define ROW_PIN_I5 155
+#define ROW_PIN_I6 154
+#define ROW_PIN_I7 153
+#define COL_PIN_O0 168
+#define COL_PIN_O1 167
+#define COL_PIN_O2 166
+#define COL_PIN_O3 165
+#define COL_PIN_O4 160
+#define COL_PIN_O5 159
+#define COL_PIN_O6 158
+#define COL_PIN_O7 157
+
+#define SKE_KPD_MAX_ROWS 8
+#define SKE_KPD_MAX_COLS 8
+
+static int ske_kp_rows[] = {
+ ROW_PIN_I0, ROW_PIN_I1, ROW_PIN_I2, ROW_PIN_I3,
+ ROW_PIN_I4, ROW_PIN_I5, ROW_PIN_I6, ROW_PIN_I7,
+};
+
+/*
+ * ske_set_gpio_row: request and set gpio rows
+ */
+static int ske_set_gpio_row(int gpio)
+{
+ int ret;
+
+ ret = gpio_request(gpio, "ske-kp");
+ if (ret < 0) {
+ pr_err("ske_set_gpio_row: gpio request failed\n");
+ return ret;
+ }
+
+ ret = gpio_direction_output(gpio, 1);
+ if (ret < 0) {
+ pr_err("ske_set_gpio_row: gpio direction failed\n");
+ gpio_free(gpio);
+ }
+
+ return ret;
+}
+
+/*
+ * ske_kp_init - enable the gpio configuration
+ */
+static int ske_kp_init(void)
+{
+ int ret, i;
+
+ for (i = 0; i < SKE_KPD_MAX_ROWS; i++) {
+ ret = ske_set_gpio_row(ske_kp_rows[i]);
+ if (ret < 0) {
+ pr_err("ske_kp_init: failed init\n");
+ return ret;
+ }
+ }
+
+ return 0;
+}
+
+static struct ske_keypad_platform_data ske_keypad_board = {
+ .init = ske_kp_init,
+ .keymap_data = &ux500_keymap_data,
+ .no_autorepeat = true,
+ .krow = SKE_KPD_MAX_ROWS, /* 8x8 matrix */
+ .kcol = SKE_KPD_MAX_COLS,
+ .debounce_ms = 40, /* in millsecs */
+};
+
+
+
/* add any platform devices here - TODO */
static struct platform_device *platform_devs[] __initdata = {
&u8500_i2c0_device,
&ux500_i2c1_device,
&ux500_i2c2_device,
&ux500_i2c3_device,
+ &ux500_ske_keypad_device,
};
static void __init u8500_init_machine(void)
ux500_i2c1_device.dev.platform_data = &u8500_i2c1_data;
ux500_i2c2_device.dev.platform_data = &u8500_i2c2_data;
ux500_i2c3_device.dev.platform_data = &u8500_i2c3_data;
+ ux500_ske_keypad_device.dev.platform_data = &ske_keypad_board;
u8500_ssp0_device.dev.platform_data = &ssp0_platform_data;
CLK(sdi5, "sdi5", NULL),
CLK(uart2, "uart2", NULL),
CLK(ske, "ske", NULL),
+ CLK(ske, "nmk-ske-keypad", NULL),
CLK(sdi2, "sdi2", NULL),
CLK(i2c0, "nmk-i2c.0", NULL),
CLK(fsmc, "fsmc", NULL),
dma40_resources[1].start = U8500_DMA_LCPA_BASE_ED;
dma40_resources[1].end = U8500_DMA_LCPA_BASE_ED + 2 * SZ_1K - 1;
}
+
+struct resource keypad_resources[] = {
+ [0] = {
+ .start = U8500_SKE_BASE,
+ .end = U8500_SKE_BASE + SZ_4K - 1,
+ .flags = IORESOURCE_MEM,
+ },
+ [1] = {
+ .start = IRQ_DB8500_KB,
+ .end = IRQ_DB8500_KB,
+ .flags = IORESOURCE_IRQ,
+ },
+};
+
+struct platform_device ux500_ske_keypad_device = {
+ .name = "nmk-ske-keypad",
+ .id = -1,
+ .num_resources = ARRAY_SIZE(keypad_resources),
+ .resource = keypad_resources,
+};
extern struct platform_device u8500_i2c0_device;
extern struct platform_device u8500_i2c4_device;
extern struct platform_device u8500_dma40_device;
+extern struct platform_device ux500_ske_keypad_device;
extern struct amba_device u8500_sdi0_device;
extern struct amba_device u8500_sdi1_device;
#define GPIO152_KP_O9 PIN_CFG(152, ALT_C)
#define GPIO153_GPIO PIN_CFG(153, GPIO)
-#define GPIO153_KP_I7 PIN_CFG(153, ALT_A)
+#define GPIO153_KP_I7 PIN_CFG_PULL(153, ALT_A, DOWN)
#define GPIO153_LCD_D24 PIN_CFG(153, ALT_B)
#define GPIO153_U2_RXD PIN_CFG(153, ALT_C)
#define GPIO154_GPIO PIN_CFG(154, GPIO)
-#define GPIO154_KP_I6 PIN_CFG(154, ALT_A)
+#define GPIO154_KP_I6 PIN_CFG_PULL(154, ALT_A, DOWN)
#define GPIO154_LCD_D25 PIN_CFG(154, ALT_B)
#define GPIO154_U2_TXD PIN_CFG(154, ALT_C)
#define GPIO155_GPIO PIN_CFG(155, GPIO)
-#define GPIO155_KP_I5 PIN_CFG(155, ALT_A)
+#define GPIO155_KP_I5 PIN_CFG_PULL(155, ALT_A, DOWN)
#define GPIO155_LCD_D26 PIN_CFG(155, ALT_B)
#define GPIO155_STMAPE_CLK PIN_CFG(155, ALT_C)
#define GPIO156_GPIO PIN_CFG(156, GPIO)
-#define GPIO156_KP_I4 PIN_CFG(156, ALT_A)
+#define GPIO156_KP_I4 PIN_CFG_PULL(156, ALT_A, DOWN)
#define GPIO156_LCD_D27 PIN_CFG(156, ALT_B)
#define GPIO156_STMAPE_DAT3 PIN_CFG(156, ALT_C)
#define GPIO157_GPIO PIN_CFG(157, GPIO)
-#define GPIO157_KP_O7 PIN_CFG(157, ALT_A)
+#define GPIO157_KP_O7 PIN_CFG_PULL(157, ALT_A, UP)
#define GPIO157_LCD_D28 PIN_CFG(157, ALT_B)
#define GPIO157_STMAPE_DAT2 PIN_CFG(157, ALT_C)
#define GPIO158_GPIO PIN_CFG(158, GPIO)
-#define GPIO158_KP_O6 PIN_CFG(158, ALT_A)
+#define GPIO158_KP_O6 PIN_CFG_PULL(158, ALT_A, UP)
#define GPIO158_LCD_D29 PIN_CFG(158, ALT_B)
#define GPIO158_STMAPE_DAT1 PIN_CFG(158, ALT_C)
#define GPIO159_GPIO PIN_CFG(159, GPIO)
-#define GPIO159_KP_O5 PIN_CFG(159, ALT_A)
+#define GPIO159_KP_O5 PIN_CFG_PULL(159, ALT_A, UP)
#define GPIO159_LCD_D30 PIN_CFG(159, ALT_B)
#define GPIO159_STMAPE_DAT0 PIN_CFG(159, ALT_C)
#define GPIO160_GPIO PIN_CFG(160, GPIO)
-#define GPIO160_KP_O4 PIN_CFG(160, ALT_A)
+#define GPIO160_KP_O4 PIN_CFG_PULL(160, ALT_A, UP)
#define GPIO160_LCD_D31 PIN_CFG(160, ALT_B)
#define GPIO160_NONE PIN_CFG(160, ALT_C)
#define GPIO161_GPIO PIN_CFG(161, GPIO)
-#define GPIO161_KP_I3 PIN_CFG(161, ALT_A)
+#define GPIO161_KP_I3 PIN_CFG_PULL(161, ALT_A, DOWN)
#define GPIO161_LCD_D32 PIN_CFG(161, ALT_B)
#define GPIO161_UARTMOD_RXD PIN_CFG(161, ALT_C)
#define GPIO162_GPIO PIN_CFG(162, GPIO)
-#define GPIO162_KP_I2 PIN_CFG(162, ALT_A)
+#define GPIO162_KP_I2 PIN_CFG_PULL(162, ALT_A, DOWN)
#define GPIO162_LCD_D33 PIN_CFG(162, ALT_B)
#define GPIO162_UARTMOD_TXD PIN_CFG(162, ALT_C)
#define GPIO163_GPIO PIN_CFG(163, GPIO)
-#define GPIO163_KP_I1 PIN_CFG(163, ALT_A)
+#define GPIO163_KP_I1 PIN_CFG_PULL(163, ALT_A, DOWN)
#define GPIO163_LCD_D34 PIN_CFG(163, ALT_B)
#define GPIO163_STMMOD_CLK PIN_CFG(163, ALT_C)
#define GPIO164_GPIO PIN_CFG(164, GPIO)
-#define GPIO164_KP_I0 PIN_CFG(164, ALT_A)
+#define GPIO164_KP_I0 PIN_CFG_PULL(164, ALT_A, UP)
#define GPIO164_LCD_D35 PIN_CFG(164, ALT_B)
#define GPIO164_STMMOD_DAT3 PIN_CFG(164, ALT_C)
#define GPIO165_GPIO PIN_CFG(165, GPIO)
-#define GPIO165_KP_O3 PIN_CFG(165, ALT_A)
+#define GPIO165_KP_O3 PIN_CFG_PULL(165, ALT_A, UP)
#define GPIO165_LCD_D36 PIN_CFG(165, ALT_B)
#define GPIO165_STMMOD_DAT2 PIN_CFG(165, ALT_C)
#define GPIO166_GPIO PIN_CFG(166, GPIO)
-#define GPIO166_KP_O2 PIN_CFG(166, ALT_A)
+#define GPIO166_KP_O2 PIN_CFG_PULL(166, ALT_A, UP)
#define GPIO166_LCD_D37 PIN_CFG(166, ALT_B)
#define GPIO166_STMMOD_DAT1 PIN_CFG(166, ALT_C)
#define GPIO167_GPIO PIN_CFG(167, GPIO)
-#define GPIO167_KP_O1 PIN_CFG(167, ALT_A)
+#define GPIO167_KP_O1 PIN_CFG_PULL(167, ALT_A, UP)
#define GPIO167_LCD_D38 PIN_CFG(167, ALT_B)
#define GPIO167_STMMOD_DAT0 PIN_CFG(167, ALT_C)
#define GPIO168_GPIO PIN_CFG(168, GPIO)
-#define GPIO168_KP_O0 PIN_CFG(168, ALT_A)
+#define GPIO168_KP_O0 PIN_CFG_PULL(168, ALT_A, UP)
#define GPIO168_LCD_D39 PIN_CFG(168, ALT_B)
#define GPIO168_NONE PIN_CFG(168, ALT_C)
--- /dev/null
+/*
+ * Copyright (C) ST-Ericsson SA 2010
+ *
+ * License Terms: GNU General Public License v2
+ * Author: Naveen Kumar Gaddipati <naveen.gaddipati@stericsson.com>
+ *
+ * ux500 Scroll key and Keypad Encoder (SKE) header
+ */
+
+#ifndef __SKE_H
+#define __SKE_H
+
+#include <linux/input/matrix_keypad.h>
+
+/* register definitions for SKE peripheral */
+#define SKE_CR 0x00
+#define SKE_VAL0 0x04
+#define SKE_VAL1 0x08
+#define SKE_DBCR 0x0C
+#define SKE_IMSC 0x10
+#define SKE_RIS 0x14
+#define SKE_MIS 0x18
+#define SKE_ICR 0x1C
+
+/*
+ * Keypad module
+ */
+
+/**
+ * struct keypad_platform_data - structure for platform specific data
+ * @init: pointer to keypad init function
+ * @exit: pointer to keypad deinitialisation function
+ * @keymap_data: matrix scan code table for keycodes
+ * @krow: maximum number of rows
+ * @kcol: maximum number of columns
+ * @debounce_ms: platform specific debounce time
+ * @no_autorepeat: flag for auto repetition
+ * @wakeup_enable: allow waking up the system
+ */
+struct ske_keypad_platform_data {
+ int (*init)(void);
+ int (*exit)(void);
+ const struct matrix_keymap_data *keymap_data;
+ u8 krow;
+ u8 kcol;
+ u8 debounce_ms;
+ bool no_autorepeat;
+ bool wakeup_enable;
+};
+#endif /*__SKE_KPD_H*/
--- /dev/null
+#ifndef ARCH_ARM_PLAT_OMAP4_KEYPAD_H
+#define ARCH_ARM_PLAT_OMAP4_KEYPAD_H
+
+#include <linux/input/matrix_keypad.h>
+
+struct omap4_keypad_platform_data {
+ const struct matrix_keymap_data *keymap_data;
+
+ u8 rows;
+ u8 cols;
+};
+
+extern int omap4_keyboard_init(struct omap4_keypad_platform_data *);
+#endif
*/
struct getset_keycode_data {
- unsigned int scancode;
- unsigned int keycode;
+ struct input_keymap_entry ke;
int error;
};
{
struct getset_keycode_data *d = data;
- d->error = input_get_keycode(handle->dev, d->scancode, &d->keycode);
+ d->error = input_get_keycode(handle->dev, &d->ke);
return d->error == 0; /* stop as soon as we successfully get one */
}
int getkeycode(unsigned int scancode)
{
- struct getset_keycode_data d = { scancode, 0, -ENODEV };
+ struct getset_keycode_data d = {
+ .ke = {
+ .flags = 0,
+ .len = sizeof(scancode),
+ .keycode = 0,
+ },
+ .error = -ENODEV,
+ };
+
+ memcpy(d.ke.scancode, &scancode, sizeof(scancode));
input_handler_for_each_handle(&kbd_handler, &d, getkeycode_helper);
- return d.error ?: d.keycode;
+ return d.error ?: d.ke.keycode;
}
static int setkeycode_helper(struct input_handle *handle, void *data)
{
struct getset_keycode_data *d = data;
- d->error = input_set_keycode(handle->dev, d->scancode, d->keycode);
+ d->error = input_set_keycode(handle->dev, &d->ke);
return d->error == 0; /* stop as soon as we successfully set one */
}
int setkeycode(unsigned int scancode, unsigned int keycode)
{
- struct getset_keycode_data d = { scancode, keycode, -ENODEV };
+ struct getset_keycode_data d = {
+ .ke = {
+ .flags = 0,
+ .len = sizeof(scancode),
+ .keycode = keycode,
+ },
+ .error = -ENODEV,
+ };
+
+ memcpy(d.ke.scancode, &scancode, sizeof(scancode));
input_handler_for_each_handle(&kbd_handler, &d, setkeycode_helper);
static bool sysrq_down;
static int sysrq_alt_use;
static int sysrq_alt;
+static DEFINE_SPINLOCK(sysrq_event_lock);
static bool sysrq_filter(struct input_handle *handle, unsigned int type,
unsigned int code, int value)
{
+ bool suppress;
+
+ /* We are called with interrupts disabled, just take the lock */
+ spin_lock(&sysrq_event_lock);
+
if (type != EV_KEY)
goto out;
}
out:
- return sysrq_down;
+ suppress = sysrq_down;
+ spin_unlock(&sysrq_event_lock);
+
+ return suppress;
}
static int sysrq_connect(struct input_handler *handler,
}
/*
- * We are matching on KEY_LEFTALT insteard of KEY_SYSRQ because not all
- * keyboards have SysRq ikey predefined and so user may add it to keymap
+ * We are matching on KEY_LEFTALT instead of KEY_SYSRQ because not all
+ * keyboards have SysRq key predefined and so user may add it to keymap
* later, but we expect all such keyboards to have left alt.
*/
static const struct input_device_id sysrq_ids[] = {
hdev->product <= USB_DEVICE_ID_SOUNDGRAPH_IMON_LAST)
return true;
break;
+ case USB_VENDOR_ID_HANWANG:
+ if (hdev->product >= USB_DEVICE_ID_HANWANG_TABLET_FIRST &&
+ hdev->product <= USB_DEVICE_ID_HANWANG_TABLET_LAST)
+ return true;
+ break;
}
if (hdev->type == HID_TYPE_USBMOUSE &&
#define USB_DEVICE_ID_GYRATION_REMOTE_2 0x0003
#define USB_DEVICE_ID_GYRATION_REMOTE_3 0x0008
+#define USB_VENDOR_ID_HANWANG 0x0b57
+#define USB_DEVICE_ID_HANWANG_TABLET_FIRST 0x5000
+#define USB_DEVICE_ID_HANWANG_TABLET_LAST 0x8fff
+
#define USB_VENDOR_ID_HAPP 0x078b
#define USB_DEVICE_ID_UGCI_DRIVING 0x0010
#define USB_DEVICE_ID_UGCI_FLYING 0x0020
#define map_key_clear(c) hid_map_usage_clear(hidinput, usage, &bit, \
&max, EV_KEY, (c))
-static inline int match_scancode(unsigned int code, unsigned int scancode)
+static bool match_scancode(struct hid_usage *usage,
+ unsigned int cur_idx, unsigned int scancode)
{
- if (scancode == 0)
- return 1;
-
- return (code & (HID_USAGE_PAGE | HID_USAGE)) == scancode;
+ return (usage->hid & (HID_USAGE_PAGE | HID_USAGE)) == scancode;
}
-static inline int match_keycode(unsigned int code, unsigned int keycode)
+static bool match_keycode(struct hid_usage *usage,
+ unsigned int cur_idx, unsigned int keycode)
{
- if (keycode == 0)
- return 1;
+ /*
+ * We should exclude unmapped usages when doing lookup by keycode.
+ */
+ return (usage->type == EV_KEY && usage->code == keycode);
+}
- return code == keycode;
+static bool match_index(struct hid_usage *usage,
+ unsigned int cur_idx, unsigned int idx)
+{
+ return cur_idx == idx;
}
+typedef bool (*hid_usage_cmp_t)(struct hid_usage *usage,
+ unsigned int cur_idx, unsigned int val);
+
static struct hid_usage *hidinput_find_key(struct hid_device *hid,
- unsigned int scancode,
- unsigned int keycode)
+ hid_usage_cmp_t match,
+ unsigned int value,
+ unsigned int *usage_idx)
{
- int i, j, k;
+ unsigned int i, j, k, cur_idx = 0;
struct hid_report *report;
struct hid_usage *usage;
for (k = HID_INPUT_REPORT; k <= HID_OUTPUT_REPORT; k++) {
list_for_each_entry(report, &hid->report_enum[k].report_list, list) {
for (i = 0; i < report->maxfield; i++) {
- for ( j = 0; j < report->field[i]->maxusage; j++) {
+ for (j = 0; j < report->field[i]->maxusage; j++) {
usage = report->field[i]->usage + j;
- if (usage->type == EV_KEY &&
- match_scancode(usage->hid, scancode) &&
- match_keycode(usage->code, keycode))
- return usage;
+ if (usage->type == EV_KEY || usage->type == 0) {
+ if (match(usage, cur_idx, value)) {
+ if (usage_idx)
+ *usage_idx = cur_idx;
+ return usage;
+ }
+ cur_idx++;
+ }
}
}
}
return NULL;
}
+static struct hid_usage *hidinput_locate_usage(struct hid_device *hid,
+ const struct input_keymap_entry *ke,
+ unsigned int *index)
+{
+ struct hid_usage *usage;
+ unsigned int scancode;
+
+ if (ke->flags & INPUT_KEYMAP_BY_INDEX)
+ usage = hidinput_find_key(hid, match_index, ke->index, index);
+ else if (input_scancode_to_scalar(ke, &scancode) == 0)
+ usage = hidinput_find_key(hid, match_scancode, scancode, index);
+ else
+ usage = NULL;
+
+ return usage;
+}
+
static int hidinput_getkeycode(struct input_dev *dev,
- unsigned int scancode, unsigned int *keycode)
+ struct input_keymap_entry *ke)
{
struct hid_device *hid = input_get_drvdata(dev);
struct hid_usage *usage;
+ unsigned int scancode, index;
- usage = hidinput_find_key(hid, scancode, 0);
+ usage = hidinput_locate_usage(hid, ke, &index);
if (usage) {
- *keycode = usage->code;
+ ke->keycode = usage->type == EV_KEY ?
+ usage->code : KEY_RESERVED;
+ ke->index = index;
+ scancode = usage->hid & (HID_USAGE_PAGE | HID_USAGE);
+ ke->len = sizeof(scancode);
+ memcpy(ke->scancode, &scancode, sizeof(scancode));
return 0;
}
+
return -EINVAL;
}
static int hidinput_setkeycode(struct input_dev *dev,
- unsigned int scancode, unsigned int keycode)
+ const struct input_keymap_entry *ke,
+ unsigned int *old_keycode)
{
struct hid_device *hid = input_get_drvdata(dev);
struct hid_usage *usage;
- int old_keycode;
- usage = hidinput_find_key(hid, scancode, 0);
+ usage = hidinput_locate_usage(hid, ke, NULL);
if (usage) {
- old_keycode = usage->code;
- usage->code = keycode;
+ *old_keycode = usage->type == EV_KEY ?
+ usage->code : KEY_RESERVED;
+ usage->code = ke->keycode;
- clear_bit(old_keycode, dev->keybit);
+ clear_bit(*old_keycode, dev->keybit);
set_bit(usage->code, dev->keybit);
- dbg_hid(KERN_DEBUG "Assigned keycode %d to HID usage code %x\n", keycode, scancode);
- /* Set the keybit for the old keycode if the old keycode is used
- * by another key */
- if (hidinput_find_key (hid, 0, old_keycode))
- set_bit(old_keycode, dev->keybit);
+ dbg_hid(KERN_DEBUG "Assigned keycode %d to HID usage code %x\n",
+ usage->code, usage->hid);
+
+ /*
+ * Set the keybit for the old keycode if the old keycode is used
+ * by another key
+ */
+ if (hidinput_find_key(hid, match_keycode, *old_keycode, NULL))
+ set_bit(*old_keycode, dev->keybit);
return 0;
}
hid->ll_driver->hidinput_input_event;
input_dev->open = hidinput_open;
input_dev->close = hidinput_close;
- input_dev->setkeycode = hidinput_setkeycode;
- input_dev->getkeycode = hidinput_getkeycode;
+ input_dev->setkeycode_new = hidinput_setkeycode;
+ input_dev->getkeycode_new = hidinput_getkeycode;
input_dev->name = hid->name;
input_dev->phys = hid->phys;
}
#undef OLD_KEY_MAX
+static int evdev_handle_get_keycode(struct input_dev *dev,
+ void __user *p, size_t size)
+{
+ struct input_keymap_entry ke;
+ int error;
+
+ memset(&ke, 0, sizeof(ke));
+
+ if (size == sizeof(unsigned int[2])) {
+ /* legacy case */
+ int __user *ip = (int __user *)p;
+
+ if (copy_from_user(ke.scancode, p, sizeof(unsigned int)))
+ return -EFAULT;
+
+ ke.len = sizeof(unsigned int);
+ ke.flags = 0;
+
+ error = input_get_keycode(dev, &ke);
+ if (error)
+ return error;
+
+ if (put_user(ke.keycode, ip + 1))
+ return -EFAULT;
+
+ } else {
+ size = min(size, sizeof(ke));
+
+ if (copy_from_user(&ke, p, size))
+ return -EFAULT;
+
+ error = input_get_keycode(dev, &ke);
+ if (error)
+ return error;
+
+ if (copy_to_user(p, &ke, size))
+ return -EFAULT;
+ }
+ return 0;
+}
+
+static int evdev_handle_set_keycode(struct input_dev *dev,
+ void __user *p, size_t size)
+{
+ struct input_keymap_entry ke;
+
+ memset(&ke, 0, sizeof(ke));
+
+ if (size == sizeof(unsigned int[2])) {
+ /* legacy case */
+ int __user *ip = (int __user *)p;
+
+ if (copy_from_user(ke.scancode, p, sizeof(unsigned int)))
+ return -EFAULT;
+
+ if (get_user(ke.keycode, ip + 1))
+ return -EFAULT;
+
+ ke.len = sizeof(unsigned int);
+ ke.flags = 0;
+
+ } else {
+ size = min(size, sizeof(ke));
+
+ if (copy_from_user(&ke, p, size))
+ return -EFAULT;
+
+ if (ke.len > sizeof(ke.scancode))
+ return -EINVAL;
+ }
+
+ return input_set_keycode(dev, &ke);
+}
+
static long evdev_do_ioctl(struct file *file, unsigned int cmd,
void __user *p, int compat_mode)
{
return 0;
- case EVIOCGKEYCODE:
- if (get_user(t, ip))
- return -EFAULT;
-
- error = input_get_keycode(dev, t, &v);
- if (error)
- return error;
-
- if (put_user(v, ip + 1))
- return -EFAULT;
-
- return 0;
-
- case EVIOCSKEYCODE:
- if (get_user(t, ip) || get_user(v, ip + 1))
- return -EFAULT;
-
- return input_set_keycode(dev, t, v);
-
case EVIOCRMFF:
return input_ff_erase(dev, (int)(unsigned long) p, file);
/* Now check variable-length commands */
#define EVIOC_MASK_SIZE(nr) ((nr) & ~(_IOC_SIZEMASK << _IOC_SIZESHIFT))
-
switch (EVIOC_MASK_SIZE(cmd)) {
case EVIOCGKEY(0):
return -EFAULT;
return error;
+
+ case EVIOC_MASK_SIZE(EVIOCGKEYCODE):
+ return evdev_handle_get_keycode(dev, p, size);
+
+ case EVIOC_MASK_SIZE(EVIOCSKEYCODE):
+ return evdev_handle_set_keycode(dev, p, size);
}
/* Multi-number variable-length handlers */
static int __devinit emu_probe(struct pci_dev *pdev, const struct pci_device_id *ent)
{
- int ioport, iolen;
struct emu *emu;
struct gameport *port;
-
- if (pci_enable_device(pdev))
- return -EBUSY;
-
- ioport = pci_resource_start(pdev, 0);
- iolen = pci_resource_len(pdev, 0);
-
- if (!request_region(ioport, iolen, "emu10k1-gp"))
- return -EBUSY;
+ int error;
emu = kzalloc(sizeof(struct emu), GFP_KERNEL);
port = gameport_allocate_port();
if (!emu || !port) {
printk(KERN_ERR "emu10k1-gp: Memory allocation failed\n");
- release_region(ioport, iolen);
- kfree(emu);
- gameport_free_port(port);
- return -ENOMEM;
+ error = -ENOMEM;
+ goto err_out_free;
}
- emu->io = ioport;
- emu->size = iolen;
+ error = pci_enable_device(pdev);
+ if (error)
+ goto err_out_free;
+
+ emu->io = pci_resource_start(pdev, 0);
+ emu->size = pci_resource_len(pdev, 0);
+
emu->dev = pdev;
emu->gameport = port;
gameport_set_name(port, "EMU10K1");
gameport_set_phys(port, "pci%s/gameport0", pci_name(pdev));
port->dev.parent = &pdev->dev;
- port->io = ioport;
+ port->io = emu->io;
+
+ if (!request_region(emu->io, emu->size, "emu10k1-gp")) {
+ printk(KERN_ERR "emu10k1-gp: unable to grab region 0x%x-0x%x\n",
+ emu->io, emu->io + emu->size - 1);
+ error = -EBUSY;
+ goto err_out_disable_dev;
+ }
pci_set_drvdata(pdev, emu);
gameport_register_port(port);
return 0;
+
+ err_out_disable_dev:
+ pci_disable_device(pdev);
+ err_out_free:
+ gameport_free_port(port);
+ kfree(emu);
+ return error;
}
static void __devexit emu_remove(struct pci_dev *pdev)
gameport_unregister_port(emu->gameport);
release_region(emu->io, emu->size);
kfree(emu);
+
+ pci_disable_device(pdev);
}
static struct pci_driver emu_driver = {
{
struct fm801_gp *gp = pci_get_drvdata(pci);
- if (gp) {
- gameport_unregister_port(gp->gameport);
- release_resource(gp->res_port);
- kfree(gp);
- }
+ gameport_unregister_port(gp->gameport);
+ release_resource(gp->res_port);
+ kfree(gp);
+
+ pci_disable_device(pci);
}
static const struct pci_device_id fm801_gp_id_table[] = {
if (code == ABS_MT_SLOT) {
/*
* "Stage" the event; we'll flush it later, when we
- * get actiual touch data.
+ * get actual touch data.
*/
if (*pval >= 0 && *pval < dev->mtsize)
dev->slot = *pval;
pold = &mtslot->abs[code - ABS_MT_FIRST];
} else {
/*
- * Bypass filtering for multitouch events when
+ * Bypass filtering for multi-touch events when
* not employing slots.
*/
pold = NULL;
spin_unlock_irq(&dev->event_lock);
}
-static int input_fetch_keycode(struct input_dev *dev, int scancode)
+/**
+ * input_scancode_to_scalar() - converts scancode in &struct input_keymap_entry
+ * @ke: keymap entry containing scancode to be converted.
+ * @scancode: pointer to the location where converted scancode should
+ * be stored.
+ *
+ * This function is used to convert scancode stored in &struct keymap_entry
+ * into scalar form understood by legacy keymap handling methods. These
+ * methods expect scancodes to be represented as 'unsigned int'.
+ */
+int input_scancode_to_scalar(const struct input_keymap_entry *ke,
+ unsigned int *scancode)
+{
+ switch (ke->len) {
+ case 1:
+ *scancode = *((u8 *)ke->scancode);
+ break;
+
+ case 2:
+ *scancode = *((u16 *)ke->scancode);
+ break;
+
+ case 4:
+ *scancode = *((u32 *)ke->scancode);
+ break;
+
+ default:
+ return -EINVAL;
+ }
+
+ return 0;
+}
+EXPORT_SYMBOL(input_scancode_to_scalar);
+
+/*
+ * Those routines handle the default case where no [gs]etkeycode() is
+ * defined. In this case, an array indexed by the scancode is used.
+ */
+
+static unsigned int input_fetch_keycode(struct input_dev *dev,
+ unsigned int index)
{
switch (dev->keycodesize) {
- case 1:
- return ((u8 *)dev->keycode)[scancode];
+ case 1:
+ return ((u8 *)dev->keycode)[index];
- case 2:
- return ((u16 *)dev->keycode)[scancode];
+ case 2:
+ return ((u16 *)dev->keycode)[index];
- default:
- return ((u32 *)dev->keycode)[scancode];
+ default:
+ return ((u32 *)dev->keycode)[index];
}
}
static int input_default_getkeycode(struct input_dev *dev,
- unsigned int scancode,
- unsigned int *keycode)
+ struct input_keymap_entry *ke)
{
+ unsigned int index;
+ int error;
+
if (!dev->keycodesize)
return -EINVAL;
- if (scancode >= dev->keycodemax)
+ if (ke->flags & INPUT_KEYMAP_BY_INDEX)
+ index = ke->index;
+ else {
+ error = input_scancode_to_scalar(ke, &index);
+ if (error)
+ return error;
+ }
+
+ if (index >= dev->keycodemax)
return -EINVAL;
- *keycode = input_fetch_keycode(dev, scancode);
+ ke->keycode = input_fetch_keycode(dev, index);
+ ke->index = index;
+ ke->len = sizeof(index);
+ memcpy(ke->scancode, &index, sizeof(index));
return 0;
}
static int input_default_setkeycode(struct input_dev *dev,
- unsigned int scancode,
- unsigned int keycode)
+ const struct input_keymap_entry *ke,
+ unsigned int *old_keycode)
{
- int old_keycode;
+ unsigned int index;
+ int error;
int i;
- if (scancode >= dev->keycodemax)
+ if (!dev->keycodesize)
return -EINVAL;
- if (!dev->keycodesize)
+ if (ke->flags & INPUT_KEYMAP_BY_INDEX) {
+ index = ke->index;
+ } else {
+ error = input_scancode_to_scalar(ke, &index);
+ if (error)
+ return error;
+ }
+
+ if (index >= dev->keycodemax)
return -EINVAL;
- if (dev->keycodesize < sizeof(keycode) && (keycode >> (dev->keycodesize * 8)))
+ if (dev->keycodesize < sizeof(dev->keycode) &&
+ (ke->keycode >> (dev->keycodesize * 8)))
return -EINVAL;
switch (dev->keycodesize) {
case 1: {
u8 *k = (u8 *)dev->keycode;
- old_keycode = k[scancode];
- k[scancode] = keycode;
+ *old_keycode = k[index];
+ k[index] = ke->keycode;
break;
}
case 2: {
u16 *k = (u16 *)dev->keycode;
- old_keycode = k[scancode];
- k[scancode] = keycode;
+ *old_keycode = k[index];
+ k[index] = ke->keycode;
break;
}
default: {
u32 *k = (u32 *)dev->keycode;
- old_keycode = k[scancode];
- k[scancode] = keycode;
+ *old_keycode = k[index];
+ k[index] = ke->keycode;
break;
}
}
- __clear_bit(old_keycode, dev->keybit);
- __set_bit(keycode, dev->keybit);
+ __clear_bit(*old_keycode, dev->keybit);
+ __set_bit(ke->keycode, dev->keybit);
for (i = 0; i < dev->keycodemax; i++) {
- if (input_fetch_keycode(dev, i) == old_keycode) {
- __set_bit(old_keycode, dev->keybit);
+ if (input_fetch_keycode(dev, i) == *old_keycode) {
+ __set_bit(*old_keycode, dev->keybit);
break; /* Setting the bit twice is useless, so break */
}
}
/**
* input_get_keycode - retrieve keycode currently mapped to a given scancode
* @dev: input device which keymap is being queried
- * @scancode: scancode (or its equivalent for device in question) for which
- * keycode is needed
- * @keycode: result
+ * @ke: keymap entry
*
* This function should be called by anyone interested in retrieving current
- * keymap. Presently keyboard and evdev handlers use it.
+ * keymap. Presently evdev handlers use it.
*/
-int input_get_keycode(struct input_dev *dev,
- unsigned int scancode, unsigned int *keycode)
+int input_get_keycode(struct input_dev *dev, struct input_keymap_entry *ke)
{
unsigned long flags;
int retval;
spin_lock_irqsave(&dev->event_lock, flags);
- retval = dev->getkeycode(dev, scancode, keycode);
- spin_unlock_irqrestore(&dev->event_lock, flags);
+ if (dev->getkeycode) {
+ /*
+ * Support for legacy drivers, that don't implement the new
+ * ioctls
+ */
+ u32 scancode = ke->index;
+
+ memcpy(ke->scancode, &scancode, sizeof(scancode));
+ ke->len = sizeof(scancode);
+ retval = dev->getkeycode(dev, scancode, &ke->keycode);
+ } else {
+ retval = dev->getkeycode_new(dev, ke);
+ }
+
+ spin_unlock_irqrestore(&dev->event_lock, flags);
return retval;
}
EXPORT_SYMBOL(input_get_keycode);
/**
- * input_get_keycode - assign new keycode to a given scancode
+ * input_set_keycode - attribute a keycode to a given scancode
* @dev: input device which keymap is being updated
- * @scancode: scancode (or its equivalent for device in question)
- * @keycode: new keycode to be assigned to the scancode
+ * @ke: new keymap entry
*
* This function should be called by anyone needing to update current
* keymap. Presently keyboard and evdev handlers use it.
*/
int input_set_keycode(struct input_dev *dev,
- unsigned int scancode, unsigned int keycode)
+ const struct input_keymap_entry *ke)
{
unsigned long flags;
unsigned int old_keycode;
int retval;
- if (keycode > KEY_MAX)
+ if (ke->keycode > KEY_MAX)
return -EINVAL;
spin_lock_irqsave(&dev->event_lock, flags);
- retval = dev->getkeycode(dev, scancode, &old_keycode);
- if (retval)
- goto out;
+ if (dev->setkeycode) {
+ /*
+ * Support for legacy drivers, that don't implement the new
+ * ioctls
+ */
+ unsigned int scancode;
+
+ retval = input_scancode_to_scalar(ke, &scancode);
+ if (retval)
+ goto out;
+
+ /*
+ * We need to know the old scancode, in order to generate a
+ * keyup effect, if the set operation happens successfully
+ */
+ if (!dev->getkeycode) {
+ retval = -EINVAL;
+ goto out;
+ }
+
+ retval = dev->getkeycode(dev, scancode, &old_keycode);
+ if (retval)
+ goto out;
+
+ retval = dev->setkeycode(dev, scancode, ke->keycode);
+ } else {
+ retval = dev->setkeycode_new(dev, ke, &old_keycode);
+ }
- retval = dev->setkeycode(dev, scancode, keycode);
if (retval)
goto out;
*
* This function allocates all necessary memory for MT slot handling in the
* input device, and adds ABS_MT_SLOT to the device capabilities. All slots
- * are initially marked as unused iby setting ABS_MT_TRACKING_ID to -1.
+ * are initially marked as unused by setting ABS_MT_TRACKING_ID to -1.
*/
int input_mt_create_slots(struct input_dev *dev, unsigned int num_slots)
{
dev->rep[REP_PERIOD] = 33;
}
- if (!dev->getkeycode)
- dev->getkeycode = input_default_getkeycode;
+ if (!dev->getkeycode && !dev->getkeycode_new)
+ dev->getkeycode_new = input_default_getkeycode;
- if (!dev->setkeycode)
- dev->setkeycode = input_default_setkeycode;
+ if (!dev->setkeycode && !dev->setkeycode_new)
+ dev->setkeycode_new = input_default_setkeycode;
dev_set_name(&dev->dev, "input%ld",
(unsigned long) atomic_inc_return(&input_no) - 1);
To compile this driver as a module, choose M here: the
module will be called newtonkbd.
+config KEYBOARD_NOMADIK
+ tristate "ST-Ericsson Nomadik SKE keyboard"
+ depends on PLAT_NOMADIK
+ help
+ Say Y here if you want to use a keypad provided on the SKE controller
+ used on the Ux500 and Nomadik platforms
+
+ To compile this driver as a module, choose M here: the
+ module will be called nmk-ske-keypad.
+
config KEYBOARD_OPENCORES
tristate "OpenCores Keyboard Controller"
help
To compile this driver as a module, choose M here: the
module will be called omap-keypad.
+config KEYBOARD_OMAP4
+ tristate "TI OMAP4 keypad support"
+ depends on ARCH_OMAP4
+ help
+ Say Y here if you want to use the OMAP4 keypad.
+
+ To compile this driver as a module, choose M here: the
+ module will be called omap4-keypad.
+
config KEYBOARD_TWL4030
tristate "TI TWL4030/TWL5030/TPS659x0 keypad support"
depends on TWL4030_CORE
obj-$(CONFIG_KEYBOARD_MAX7359) += max7359_keypad.o
obj-$(CONFIG_KEYBOARD_MCS) += mcs_touchkey.o
obj-$(CONFIG_KEYBOARD_NEWTON) += newtonkbd.o
+obj-$(CONFIG_KEYBOARD_NOMADIK) += nomadik-ske-keypad.o
obj-$(CONFIG_KEYBOARD_OMAP) += omap-keypad.o
+obj-$(CONFIG_KEYBOARD_OMAP4) += omap4-keypad.o
obj-$(CONFIG_KEYBOARD_OPENCORES) += opencores-kbd.o
obj-$(CONFIG_KEYBOARD_PXA27x) += pxa27x_keypad.o
obj-$(CONFIG_KEYBOARD_PXA930_ROTARY) += pxa930_rotary.o
#endif
static const struct i2c_device_id adp5588_id[] = {
- { KBUILD_MODNAME, 0 },
+ { "adp5588-keys", 0 },
{ "adp5587-keys", 0 },
{ }
};
{ 0 }
};
+MODULE_DEVICE_TABLE(serio, hil_dev_ids);
+
static struct serio_driver hil_serio_drv = {
.driver = {
.name = "hil_dev",
--- /dev/null
+/*
+ * Copyright (C) ST-Ericsson SA 2010
+ *
+ * Author: Naveen Kumar G <naveen.gaddipati@stericsson.com> for ST-Ericsson
+ * Author: Sundar Iyer <sundar.iyer@stericsson.com> for ST-Ericsson
+ *
+ * License terms:GNU General Public License (GPL) version 2
+ *
+ * Keypad controller driver for the SKE (Scroll Key Encoder) module used in
+ * the Nomadik 8815 and Ux500 platforms.
+ */
+
+#include <linux/platform_device.h>
+#include <linux/interrupt.h>
+#include <linux/spinlock.h>
+#include <linux/io.h>
+#include <linux/delay.h>
+#include <linux/input.h>
+#include <linux/slab.h>
+#include <linux/clk.h>
+
+#include <plat/ske.h>
+
+/* SKE_CR bits */
+#define SKE_KPMLT (0x1 << 6)
+#define SKE_KPCN (0x7 << 3)
+#define SKE_KPASEN (0x1 << 2)
+#define SKE_KPASON (0x1 << 7)
+
+/* SKE_IMSC bits */
+#define SKE_KPIMA (0x1 << 2)
+
+/* SKE_ICR bits */
+#define SKE_KPICS (0x1 << 3)
+#define SKE_KPICA (0x1 << 2)
+
+/* SKE_RIS bits */
+#define SKE_KPRISA (0x1 << 2)
+
+#define SKE_KEYPAD_ROW_SHIFT 3
+#define SKE_KPD_KEYMAP_SIZE (8 * 8)
+
+/* keypad auto scan registers */
+#define SKE_ASR0 0x20
+#define SKE_ASR1 0x24
+#define SKE_ASR2 0x28
+#define SKE_ASR3 0x2C
+
+#define SKE_NUM_ASRX_REGISTERS (4)
+
+/**
+ * struct ske_keypad - data structure used by keypad driver
+ * @irq: irq no
+ * @reg_base: ske regsiters base address
+ * @input: pointer to input device object
+ * @board: keypad platform device
+ * @keymap: matrix scan code table for keycodes
+ * @clk: clock structure pointer
+ */
+struct ske_keypad {
+ int irq;
+ void __iomem *reg_base;
+ struct input_dev *input;
+ const struct ske_keypad_platform_data *board;
+ unsigned short keymap[SKE_KPD_KEYMAP_SIZE];
+ struct clk *clk;
+ spinlock_t ske_keypad_lock;
+};
+
+static void ske_keypad_set_bits(struct ske_keypad *keypad, u16 addr,
+ u8 mask, u8 data)
+{
+ u32 ret;
+
+ spin_lock(&keypad->ske_keypad_lock);
+
+ ret = readl(keypad->reg_base + addr);
+ ret &= ~mask;
+ ret |= data;
+ writel(ret, keypad->reg_base + addr);
+
+ spin_unlock(&keypad->ske_keypad_lock);
+}
+
+/*
+ * ske_keypad_chip_init: init keypad controller configuration
+ *
+ * Enable Multi key press detection, auto scan mode
+ */
+static int __devinit ske_keypad_chip_init(struct ske_keypad *keypad)
+{
+ u32 value;
+ int timeout = 50;
+
+ /* check SKE_RIS to be 0 */
+ while ((readl(keypad->reg_base + SKE_RIS) != 0x00000000) && timeout--)
+ cpu_relax();
+
+ if (!timeout)
+ return -EINVAL;
+
+ /*
+ * set debounce value
+ * keypad dbounce is configured in DBCR[15:8]
+ * dbounce value in steps of 32/32.768 ms
+ */
+ spin_lock(&keypad->ske_keypad_lock);
+ value = readl(keypad->reg_base + SKE_DBCR);
+ value = value & 0xff;
+ value |= ((keypad->board->debounce_ms * 32000)/32768) << 8;
+ writel(value, keypad->reg_base + SKE_DBCR);
+ spin_unlock(&keypad->ske_keypad_lock);
+
+ /* enable multi key detection */
+ ske_keypad_set_bits(keypad, SKE_CR, 0x0, SKE_KPMLT);
+
+ /*
+ * set up the number of columns
+ * KPCN[5:3] defines no. of keypad columns to be auto scanned
+ */
+ value = (keypad->board->kcol - 1) << 3;
+ ske_keypad_set_bits(keypad, SKE_CR, SKE_KPCN, value);
+
+ /* clear keypad interrupt for auto(and pending SW) scans */
+ ske_keypad_set_bits(keypad, SKE_ICR, 0x0, SKE_KPICA | SKE_KPICS);
+
+ /* un-mask keypad interrupts */
+ ske_keypad_set_bits(keypad, SKE_IMSC, 0x0, SKE_KPIMA);
+
+ /* enable automatic scan */
+ ske_keypad_set_bits(keypad, SKE_CR, 0x0, SKE_KPASEN);
+
+ return 0;
+}
+
+static void ske_keypad_read_data(struct ske_keypad *keypad)
+{
+ struct input_dev *input = keypad->input;
+ u16 status;
+ int col = 0, row = 0, code;
+ int ske_asr, ske_ris, key_pressed, i;
+
+ /*
+ * Read the auto scan registers
+ *
+ * Each SKE_ASRx (x=0 to x=3) contains two row values.
+ * lower byte contains row value for column 2*x,
+ * upper byte contains row value for column 2*x + 1
+ */
+ for (i = 0; i < SKE_NUM_ASRX_REGISTERS; i++) {
+ ske_asr = readl(keypad->reg_base + SKE_ASR0 + (4 * i));
+ if (!ske_asr)
+ continue;
+
+ /* now that ASRx is zero, find out the column x and row y*/
+ if (ske_asr & 0xff) {
+ col = i * 2;
+ status = ske_asr & 0xff;
+ } else {
+ col = (i * 2) + 1;
+ status = (ske_asr & 0xff00) >> 8;
+ }
+
+ /* find out the row */
+ row = __ffs(status);
+
+ code = MATRIX_SCAN_CODE(row, col, SKE_KEYPAD_ROW_SHIFT);
+ ske_ris = readl(keypad->reg_base + SKE_RIS);
+ key_pressed = ske_ris & SKE_KPRISA;
+
+ input_event(input, EV_MSC, MSC_SCAN, code);
+ input_report_key(input, keypad->keymap[code], key_pressed);
+ input_sync(input);
+ }
+}
+
+static irqreturn_t ske_keypad_irq(int irq, void *dev_id)
+{
+ struct ske_keypad *keypad = dev_id;
+ int retries = 20;
+
+ /* disable auto scan interrupt; mask the interrupt generated */
+ ske_keypad_set_bits(keypad, SKE_IMSC, ~SKE_KPIMA, 0x0);
+ ske_keypad_set_bits(keypad, SKE_ICR, 0x0, SKE_KPICA);
+
+ while ((readl(keypad->reg_base + SKE_CR) & SKE_KPASON) && --retries)
+ msleep(5);
+
+ if (retries) {
+ /* SKEx registers are stable and can be read */
+ ske_keypad_read_data(keypad);
+ }
+
+ /* enable auto scan interrupts */
+ ske_keypad_set_bits(keypad, SKE_IMSC, 0x0, SKE_KPIMA);
+
+ return IRQ_HANDLED;
+}
+
+static int __devinit ske_keypad_probe(struct platform_device *pdev)
+{
+ const struct ske_keypad_platform_data *plat = pdev->dev.platform_data;
+ struct ske_keypad *keypad;
+ struct input_dev *input;
+ struct resource *res;
+ int irq;
+ int error;
+
+ if (!plat) {
+ dev_err(&pdev->dev, "invalid keypad platform data\n");
+ return -EINVAL;
+ }
+
+ irq = platform_get_irq(pdev, 0);
+ if (irq < 0) {
+ dev_err(&pdev->dev, "failed to get keypad irq\n");
+ return -EINVAL;
+ }
+
+ res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+ if (!res) {
+ dev_err(&pdev->dev, "missing platform resources\n");
+ return -EINVAL;
+ }
+
+ keypad = kzalloc(sizeof(struct ske_keypad), GFP_KERNEL);
+ input = input_allocate_device();
+ if (!keypad || !input) {
+ dev_err(&pdev->dev, "failed to allocate keypad memory\n");
+ error = -ENOMEM;
+ goto err_free_mem;
+ }
+
+ keypad->irq = irq;
+ keypad->board = plat;
+ keypad->input = input;
+ spin_lock_init(&keypad->ske_keypad_lock);
+
+ if (!request_mem_region(res->start, resource_size(res), pdev->name)) {
+ dev_err(&pdev->dev, "failed to request I/O memory\n");
+ error = -EBUSY;
+ goto err_free_mem;
+ }
+
+ keypad->reg_base = ioremap(res->start, resource_size(res));
+ if (!keypad->reg_base) {
+ dev_err(&pdev->dev, "failed to remap I/O memory\n");
+ error = -ENXIO;
+ goto err_free_mem_region;
+ }
+
+ keypad->clk = clk_get(&pdev->dev, NULL);
+ if (IS_ERR(keypad->clk)) {
+ dev_err(&pdev->dev, "failed to get clk\n");
+ error = PTR_ERR(keypad->clk);
+ goto err_iounmap;
+ }
+
+ input->id.bustype = BUS_HOST;
+ input->name = "ux500-ske-keypad";
+ input->dev.parent = &pdev->dev;
+
+ input->keycode = keypad->keymap;
+ input->keycodesize = sizeof(keypad->keymap[0]);
+ input->keycodemax = ARRAY_SIZE(keypad->keymap);
+
+ input_set_capability(input, EV_MSC, MSC_SCAN);
+
+ __set_bit(EV_KEY, input->evbit);
+ if (!plat->no_autorepeat)
+ __set_bit(EV_REP, input->evbit);
+
+ matrix_keypad_build_keymap(plat->keymap_data, SKE_KEYPAD_ROW_SHIFT,
+ input->keycode, input->keybit);
+
+ clk_enable(keypad->clk);
+
+ /* go through board initialization helpers */
+ if (keypad->board->init)
+ keypad->board->init();
+
+ error = ske_keypad_chip_init(keypad);
+ if (error) {
+ dev_err(&pdev->dev, "unable to init keypad hardware\n");
+ goto err_clk_disable;
+ }
+
+ error = request_threaded_irq(keypad->irq, NULL, ske_keypad_irq,
+ IRQF_ONESHOT, "ske-keypad", keypad);
+ if (error) {
+ dev_err(&pdev->dev, "allocate irq %d failed\n", keypad->irq);
+ goto err_clk_disable;
+ }
+
+ error = input_register_device(input);
+ if (error) {
+ dev_err(&pdev->dev,
+ "unable to register input device: %d\n", error);
+ goto err_free_irq;
+ }
+
+ if (plat->wakeup_enable)
+ device_init_wakeup(&pdev->dev, true);
+
+ platform_set_drvdata(pdev, keypad);
+
+ return 0;
+
+err_free_irq:
+ free_irq(keypad->irq, keypad);
+err_clk_disable:
+ clk_disable(keypad->clk);
+ clk_put(keypad->clk);
+err_iounmap:
+ iounmap(keypad->reg_base);
+err_free_mem_region:
+ release_mem_region(res->start, resource_size(res));
+err_free_mem:
+ input_free_device(input);
+ kfree(keypad);
+ return error;
+}
+
+static int __devexit ske_keypad_remove(struct platform_device *pdev)
+{
+ struct ske_keypad *keypad = platform_get_drvdata(pdev);
+ struct resource *res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+
+ free_irq(keypad->irq, keypad);
+
+ input_unregister_device(keypad->input);
+
+ clk_disable(keypad->clk);
+ clk_put(keypad->clk);
+
+ if (keypad->board->exit)
+ keypad->board->exit();
+
+ iounmap(keypad->reg_base);
+ release_mem_region(res->start, resource_size(res));
+ kfree(keypad);
+
+ return 0;
+}
+
+#ifdef CONFIG_PM
+static int ske_keypad_suspend(struct device *dev)
+{
+ struct platform_device *pdev = to_platform_device(dev);
+ struct ske_keypad *keypad = platform_get_drvdata(pdev);
+ int irq = platform_get_irq(pdev, 0);
+
+ if (device_may_wakeup(dev))
+ enable_irq_wake(irq);
+ else
+ ske_keypad_set_bits(keypad, SKE_IMSC, ~SKE_KPIMA, 0x0);
+
+ return 0;
+}
+
+static int ske_keypad_resume(struct device *dev)
+{
+ struct platform_device *pdev = to_platform_device(dev);
+ struct ske_keypad *keypad = platform_get_drvdata(pdev);
+ int irq = platform_get_irq(pdev, 0);
+
+ if (device_may_wakeup(dev))
+ disable_irq_wake(irq);
+ else
+ ske_keypad_set_bits(keypad, SKE_IMSC, 0x0, SKE_KPIMA);
+
+ return 0;
+}
+
+static const struct dev_pm_ops ske_keypad_dev_pm_ops = {
+ .suspend = ske_keypad_suspend,
+ .resume = ske_keypad_resume,
+};
+#endif
+
+struct platform_driver ske_keypad_driver = {
+ .driver = {
+ .name = "nmk-ske-keypad",
+ .owner = THIS_MODULE,
+#ifdef CONFIG_PM
+ .pm = &ske_keypad_dev_pm_ops,
+#endif
+ },
+ .probe = ske_keypad_probe,
+ .remove = __devexit_p(ske_keypad_remove),
+};
+
+static int __init ske_keypad_init(void)
+{
+ return platform_driver_probe(&ske_keypad_driver, ske_keypad_probe);
+}
+module_init(ske_keypad_init);
+
+static void __exit ske_keypad_exit(void)
+{
+ platform_driver_unregister(&ske_keypad_driver);
+}
+module_exit(ske_keypad_exit);
+
+MODULE_LICENSE("GPL v2");
+MODULE_AUTHOR("Naveen Kumar <naveen.gaddipati@stericsson.com> / Sundar Iyer <sundar.iyer@stericsson.com>");
+MODULE_DESCRIPTION("Nomadik Scroll-Key-Encoder Keypad Driver");
+MODULE_ALIAS("platform:nomadik-ske-keypad");
--- /dev/null
+/*
+ * OMAP4 Keypad Driver
+ *
+ * Copyright (C) 2010 Texas Instruments
+ *
+ * Author: Abraham Arce <x0066660@ti.com>
+ * Initial Code: Syed Rafiuddin <rafiuddin.syed@ti.com>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA
+ */
+
+#include <linux/module.h>
+#include <linux/init.h>
+#include <linux/interrupt.h>
+#include <linux/platform_device.h>
+#include <linux/errno.h>
+#include <linux/io.h>
+#include <linux/input.h>
+#include <linux/slab.h>
+
+#include <plat/omap4-keypad.h>
+
+/* OMAP4 registers */
+#define OMAP4_KBD_REVISION 0x00
+#define OMAP4_KBD_SYSCONFIG 0x10
+#define OMAP4_KBD_SYSSTATUS 0x14
+#define OMAP4_KBD_IRQSTATUS 0x18
+#define OMAP4_KBD_IRQENABLE 0x1C
+#define OMAP4_KBD_WAKEUPENABLE 0x20
+#define OMAP4_KBD_PENDING 0x24
+#define OMAP4_KBD_CTRL 0x28
+#define OMAP4_KBD_DEBOUNCINGTIME 0x2C
+#define OMAP4_KBD_LONGKEYTIME 0x30
+#define OMAP4_KBD_TIMEOUT 0x34
+#define OMAP4_KBD_STATEMACHINE 0x38
+#define OMAP4_KBD_ROWINPUTS 0x3C
+#define OMAP4_KBD_COLUMNOUTPUTS 0x40
+#define OMAP4_KBD_FULLCODE31_0 0x44
+#define OMAP4_KBD_FULLCODE63_32 0x48
+
+/* OMAP4 bit definitions */
+#define OMAP4_DEF_IRQENABLE_EVENTEN (1 << 0)
+#define OMAP4_DEF_IRQENABLE_LONGKEY (1 << 1)
+#define OMAP4_DEF_IRQENABLE_TIMEOUTEN (1 << 2)
+#define OMAP4_DEF_WUP_EVENT_ENA (1 << 0)
+#define OMAP4_DEF_WUP_LONG_KEY_ENA (1 << 1)
+#define OMAP4_DEF_CTRL_NOSOFTMODE (1 << 1)
+#define OMAP4_DEF_CTRLPTVVALUE (1 << 2)
+#define OMAP4_DEF_CTRLPTV (1 << 1)
+
+/* OMAP4 values */
+#define OMAP4_VAL_IRQDISABLE 0x00
+#define OMAP4_VAL_DEBOUNCINGTIME 0x07
+#define OMAP4_VAL_FUNCTIONALCFG 0x1E
+
+#define OMAP4_MASK_IRQSTATUSDISABLE 0xFFFF
+
+struct omap4_keypad {
+ struct input_dev *input;
+
+ void __iomem *base;
+ int irq;
+
+ unsigned int rows;
+ unsigned int cols;
+ unsigned int row_shift;
+ unsigned char key_state[8];
+ unsigned short keymap[];
+};
+
+static void __devinit omap4_keypad_config(struct omap4_keypad *keypad_data)
+{
+ __raw_writel(OMAP4_VAL_FUNCTIONALCFG,
+ keypad_data->base + OMAP4_KBD_CTRL);
+ __raw_writel(OMAP4_VAL_DEBOUNCINGTIME,
+ keypad_data->base + OMAP4_KBD_DEBOUNCINGTIME);
+ __raw_writel(OMAP4_VAL_IRQDISABLE,
+ keypad_data->base + OMAP4_KBD_IRQSTATUS);
+ __raw_writel(OMAP4_DEF_IRQENABLE_EVENTEN | OMAP4_DEF_IRQENABLE_LONGKEY,
+ keypad_data->base + OMAP4_KBD_IRQENABLE);
+ __raw_writel(OMAP4_DEF_WUP_EVENT_ENA | OMAP4_DEF_WUP_LONG_KEY_ENA,
+ keypad_data->base + OMAP4_KBD_WAKEUPENABLE);
+}
+
+/* Interrupt handler */
+static irqreturn_t omap4_keypad_interrupt(int irq, void *dev_id)
+{
+ struct omap4_keypad *keypad_data = dev_id;
+ struct input_dev *input_dev = keypad_data->input;
+ unsigned char key_state[ARRAY_SIZE(keypad_data->key_state)];
+ unsigned int col, row, code, changed;
+ u32 *new_state = (u32 *) key_state;
+
+ /* Disable interrupts */
+ __raw_writel(OMAP4_VAL_IRQDISABLE,
+ keypad_data->base + OMAP4_KBD_IRQENABLE);
+
+ *new_state = __raw_readl(keypad_data->base + OMAP4_KBD_FULLCODE31_0);
+ *(new_state + 1) = __raw_readl(keypad_data->base
+ + OMAP4_KBD_FULLCODE63_32);
+
+ for (row = 0; row < keypad_data->rows; row++) {
+ changed = key_state[row] ^ keypad_data->key_state[row];
+ if (!changed)
+ continue;
+
+ for (col = 0; col < keypad_data->cols; col++) {
+ if (changed & (1 << col)) {
+ code = MATRIX_SCAN_CODE(row, col,
+ keypad_data->row_shift);
+ input_event(input_dev, EV_MSC, MSC_SCAN, code);
+ input_report_key(input_dev,
+ keypad_data->keymap[code],
+ key_state[row] & (1 << col));
+ }
+ }
+ }
+
+ input_sync(input_dev);
+
+ memcpy(keypad_data->key_state, key_state,
+ sizeof(keypad_data->key_state));
+
+ /* clear pending interrupts */
+ __raw_writel(__raw_readl(keypad_data->base + OMAP4_KBD_IRQSTATUS),
+ keypad_data->base + OMAP4_KBD_IRQSTATUS);
+
+ /* enable interrupts */
+ __raw_writel(OMAP4_DEF_IRQENABLE_EVENTEN | OMAP4_DEF_IRQENABLE_LONGKEY,
+ keypad_data->base + OMAP4_KBD_IRQENABLE);
+
+ return IRQ_HANDLED;
+}
+
+static int __devinit omap4_keypad_probe(struct platform_device *pdev)
+{
+ const struct omap4_keypad_platform_data *pdata;
+ struct omap4_keypad *keypad_data;
+ struct input_dev *input_dev;
+ struct resource *res;
+ resource_size_t size;
+ unsigned int row_shift, max_keys;
+ int irq;
+ int error;
+
+ /* platform data */
+ pdata = pdev->dev.platform_data;
+ if (!pdata) {
+ dev_err(&pdev->dev, "no platform data defined\n");
+ return -EINVAL;
+ }
+
+ res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+ if (!res) {
+ dev_err(&pdev->dev, "no base address specified\n");
+ return -EINVAL;
+ }
+
+ irq = platform_get_irq(pdev, 0);
+ if (!irq) {
+ dev_err(&pdev->dev, "no keyboard irq assigned\n");
+ return -EINVAL;
+ }
+
+ if (!pdata->keymap_data) {
+ dev_err(&pdev->dev, "no keymap data defined\n");
+ return -EINVAL;
+ }
+
+ row_shift = get_count_order(pdata->cols);
+ max_keys = pdata->rows << row_shift;
+
+ keypad_data = kzalloc(sizeof(struct omap4_keypad) +
+ max_keys * sizeof(keypad_data->keymap[0]),
+ GFP_KERNEL);
+ if (!keypad_data) {
+ dev_err(&pdev->dev, "keypad_data memory allocation failed\n");
+ return -ENOMEM;
+ }
+
+ size = resource_size(res);
+
+ res = request_mem_region(res->start, size, pdev->name);
+ if (!res) {
+ dev_err(&pdev->dev, "can't request mem region\n");
+ error = -EBUSY;
+ goto err_free_keypad;
+ }
+
+ keypad_data->base = ioremap(res->start, resource_size(res));
+ if (!keypad_data->base) {
+ dev_err(&pdev->dev, "can't ioremap mem resource\n");
+ error = -ENOMEM;
+ goto err_release_mem;
+ }
+
+ keypad_data->irq = irq;
+ keypad_data->row_shift = row_shift;
+ keypad_data->rows = pdata->rows;
+ keypad_data->cols = pdata->cols;
+
+ /* input device allocation */
+ keypad_data->input = input_dev = input_allocate_device();
+ if (!input_dev) {
+ error = -ENOMEM;
+ goto err_unmap;
+ }
+
+ input_dev->name = pdev->name;
+ input_dev->dev.parent = &pdev->dev;
+ input_dev->id.bustype = BUS_HOST;
+ input_dev->id.vendor = 0x0001;
+ input_dev->id.product = 0x0001;
+ input_dev->id.version = 0x0001;
+
+ input_dev->keycode = keypad_data->keymap;
+ input_dev->keycodesize = sizeof(keypad_data->keymap[0]);
+ input_dev->keycodemax = max_keys;
+
+ __set_bit(EV_KEY, input_dev->evbit);
+ __set_bit(EV_REP, input_dev->evbit);
+
+ input_set_capability(input_dev, EV_MSC, MSC_SCAN);
+
+ input_set_drvdata(input_dev, keypad_data);
+
+ matrix_keypad_build_keymap(pdata->keymap_data, row_shift,
+ input_dev->keycode, input_dev->keybit);
+
+ omap4_keypad_config(keypad_data);
+
+ error = request_irq(keypad_data->irq, omap4_keypad_interrupt,
+ IRQF_TRIGGER_RISING,
+ "omap4-keypad", keypad_data);
+ if (error) {
+ dev_err(&pdev->dev, "failed to register interrupt\n");
+ goto err_free_input;
+ }
+
+ error = input_register_device(keypad_data->input);
+ if (error < 0) {
+ dev_err(&pdev->dev, "failed to register input device\n");
+ goto err_free_irq;
+ }
+
+
+ platform_set_drvdata(pdev, keypad_data);
+ return 0;
+
+err_free_irq:
+ free_irq(keypad_data->irq, keypad_data);
+err_free_input:
+ input_free_device(input_dev);
+err_unmap:
+ iounmap(keypad_data->base);
+err_release_mem:
+ release_mem_region(res->start, size);
+err_free_keypad:
+ kfree(keypad_data);
+ return error;
+}
+
+static int __devexit omap4_keypad_remove(struct platform_device *pdev)
+{
+ struct omap4_keypad *keypad_data = platform_get_drvdata(pdev);
+ struct resource *res;
+
+ free_irq(keypad_data->irq, keypad_data);
+ input_unregister_device(keypad_data->input);
+
+ iounmap(keypad_data->base);
+
+ res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+ release_mem_region(res->start, resource_size(res));
+
+ kfree(keypad_data);
+ platform_set_drvdata(pdev, NULL);
+
+ return 0;
+}
+
+static struct platform_driver omap4_keypad_driver = {
+ .probe = omap4_keypad_probe,
+ .remove = __devexit_p(omap4_keypad_remove),
+ .driver = {
+ .name = "omap4-keypad",
+ .owner = THIS_MODULE,
+ },
+};
+
+static int __init omap4_keypad_init(void)
+{
+ return platform_driver_register(&omap4_keypad_driver);
+}
+module_init(omap4_keypad_init);
+
+static void __exit omap4_keypad_exit(void)
+{
+ platform_driver_unregister(&omap4_keypad_driver);
+}
+module_exit(omap4_keypad_exit);
+
+MODULE_AUTHOR("Texas Instruments");
+MODULE_DESCRIPTION("OMAP4 Keypad Driver");
+MODULE_LICENSE("GPL");
+MODULE_ALIAS("platform:omap4-keypad");
if (error) {
dev_info(kp->dbg_dev, "request_irq failed for irq no=%d\n",
kp->irq);
- goto err3;
+ goto err2;
}
/* Enable KP and TO interrupts now. */
reg = (u8) ~(KEYP_IMR1_KP | KEYP_IMR1_TO);
if (twl4030_kpwrite_u8(kp, reg, KEYP_IMR1)) {
error = -EIO;
- goto err4;
+ goto err3;
}
platform_set_drvdata(pdev, kp);
return 0;
-err4:
+err3:
/* mask all events - we don't care about the result */
(void) twl4030_kpwrite_u8(kp, 0xff, KEYP_IMR1);
-err3:
free_irq(kp->irq, NULL);
err2:
input_unregister_device(input);
To compile this driver as a module, choose M here: the module
will be called 88pm860x_onkey.
+config INPUT_AB8500_PONKEY
+ tristate "AB8500 Pon (PowerOn) Key"
+ depends on AB8500_CORE
+ help
+ Say Y here to use the PowerOn Key for ST-Ericsson's AB8500
+ Mix-Sig PMIC.
+
+ To compile this driver as a module, choose M here: the module
+ will be called ab8500-ponkey.
+
config INPUT_AD714X
tristate "Analog Devices AD714x Capacitance Touch Sensor"
help
# Each configuration option enables a list of files.
obj-$(CONFIG_INPUT_88PM860X_ONKEY) += 88pm860x_onkey.o
+obj-$(CONFIG_INPUT_AB8500_PONKEY) += ab8500-ponkey.o
obj-$(CONFIG_INPUT_AD714X) += ad714x.o
obj-$(CONFIG_INPUT_AD714X_I2C) += ad714x-i2c.o
obj-$(CONFIG_INPUT_AD714X_SPI) += ad714x-spi.o
--- /dev/null
+/*
+ * Copyright (C) ST-Ericsson SA 2010
+ *
+ * License Terms: GNU General Public License v2
+ * Author: Sundar Iyer <sundar.iyer@stericsson.com> for ST-Ericsson
+ *
+ * AB8500 Power-On Key handler
+ */
+
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/platform_device.h>
+#include <linux/input.h>
+#include <linux/interrupt.h>
+#include <linux/mfd/ab8500.h>
+#include <linux/slab.h>
+
+/**
+ * struct ab8500_ponkey - ab8500 ponkey information
+ * @input_dev: pointer to input device
+ * @ab8500: ab8500 parent
+ * @irq_dbf: irq number for falling transition
+ * @irq_dbr: irq number for rising transition
+ */
+struct ab8500_ponkey {
+ struct input_dev *idev;
+ struct ab8500 *ab8500;
+ int irq_dbf;
+ int irq_dbr;
+};
+
+/* AB8500 gives us an interrupt when ONKEY is held */
+static irqreturn_t ab8500_ponkey_handler(int irq, void *data)
+{
+ struct ab8500_ponkey *ponkey = data;
+
+ if (irq == ponkey->irq_dbf)
+ input_report_key(ponkey->idev, KEY_POWER, true);
+ else if (irq == ponkey->irq_dbr)
+ input_report_key(ponkey->idev, KEY_POWER, false);
+
+ input_sync(ponkey->idev);
+
+ return IRQ_HANDLED;
+}
+
+static int __devinit ab8500_ponkey_probe(struct platform_device *pdev)
+{
+ struct ab8500 *ab8500 = dev_get_drvdata(pdev->dev.parent);
+ struct ab8500_ponkey *ponkey;
+ struct input_dev *input;
+ int irq_dbf, irq_dbr;
+ int error;
+
+ irq_dbf = platform_get_irq_byname(pdev, "ONKEY_DBF");
+ if (irq_dbf < 0) {
+ dev_err(&pdev->dev, "No IRQ for ONKEY_DBF, error=%d\n", irq_dbf);
+ return irq_dbf;
+ }
+
+ irq_dbr = platform_get_irq_byname(pdev, "ONKEY_DBR");
+ if (irq_dbr < 0) {
+ dev_err(&pdev->dev, "No IRQ for ONKEY_DBR, error=%d\n", irq_dbr);
+ return irq_dbr;
+ }
+
+ ponkey = kzalloc(sizeof(struct ab8500_ponkey), GFP_KERNEL);
+ input = input_allocate_device();
+ if (!ponkey || !input) {
+ error = -ENOMEM;
+ goto err_free_mem;
+ }
+
+ ponkey->idev = input;
+ ponkey->ab8500 = ab8500;
+ ponkey->irq_dbf = irq_dbf;
+ ponkey->irq_dbr = irq_dbr;
+
+ input->name = "AB8500 POn(PowerOn) Key";
+ input->dev.parent = &pdev->dev;
+
+ input_set_capability(input, EV_KEY, KEY_POWER);
+
+ error = request_any_context_irq(ponkey->irq_dbf, ab8500_ponkey_handler,
+ 0, "ab8500-ponkey-dbf", ponkey);
+ if (error < 0) {
+ dev_err(ab8500->dev, "Failed to request dbf IRQ#%d: %d\n",
+ ponkey->irq_dbf, error);
+ goto err_free_mem;
+ }
+
+ error = request_any_context_irq(ponkey->irq_dbr, ab8500_ponkey_handler,
+ 0, "ab8500-ponkey-dbr", ponkey);
+ if (error < 0) {
+ dev_err(ab8500->dev, "Failed to request dbr IRQ#%d: %d\n",
+ ponkey->irq_dbr, error);
+ goto err_free_dbf_irq;
+ }
+
+ error = input_register_device(ponkey->idev);
+ if (error) {
+ dev_err(ab8500->dev, "Can't register input device: %d\n", error);
+ goto err_free_dbr_irq;
+ }
+
+ platform_set_drvdata(pdev, ponkey);
+ return 0;
+
+err_free_dbr_irq:
+ free_irq(ponkey->irq_dbr, ponkey);
+err_free_dbf_irq:
+ free_irq(ponkey->irq_dbf, ponkey);
+err_free_mem:
+ input_free_device(input);
+ kfree(ponkey);
+
+ return error;
+}
+
+static int __devexit ab8500_ponkey_remove(struct platform_device *pdev)
+{
+ struct ab8500_ponkey *ponkey = platform_get_drvdata(pdev);
+
+ free_irq(ponkey->irq_dbf, ponkey);
+ free_irq(ponkey->irq_dbr, ponkey);
+ input_unregister_device(ponkey->idev);
+ kfree(ponkey);
+
+ platform_set_drvdata(pdev, NULL);
+
+ return 0;
+}
+
+static struct platform_driver ab8500_ponkey_driver = {
+ .driver = {
+ .name = "ab8500-poweron-key",
+ .owner = THIS_MODULE,
+ },
+ .probe = ab8500_ponkey_probe,
+ .remove = __devexit_p(ab8500_ponkey_remove),
+};
+
+static int __init ab8500_ponkey_init(void)
+{
+ return platform_driver_register(&ab8500_ponkey_driver);
+}
+module_init(ab8500_ponkey_init);
+
+static void __exit ab8500_ponkey_exit(void)
+{
+ platform_driver_unregister(&ab8500_ponkey_driver);
+}
+module_exit(ab8500_ponkey_exit);
+
+MODULE_LICENSE("GPL v2");
+MODULE_AUTHOR("Sundar Iyer <sundar.iyer@stericsson.com>");
+MODULE_DESCRIPTION("ST-Ericsson AB8500 Power-ON(Pon) Key driver");
}
static int ati_remote2_getkeycode(struct input_dev *idev,
- unsigned int scancode, unsigned int *keycode)
+ struct input_keymap_entry *ke)
{
struct ati_remote2 *ar2 = input_get_drvdata(idev);
unsigned int mode;
- int index;
+ int offset;
+ unsigned int index;
+ unsigned int scancode;
+
+ if (ke->flags & INPUT_KEYMAP_BY_INDEX) {
+ index = ke->index;
+ if (index >= ATI_REMOTE2_MODES *
+ ARRAY_SIZE(ati_remote2_key_table))
+ return -EINVAL;
+
+ mode = ke->index / ARRAY_SIZE(ati_remote2_key_table);
+ offset = ke->index % ARRAY_SIZE(ati_remote2_key_table);
+ scancode = (mode << 8) + ati_remote2_key_table[offset].hw_code;
+ } else {
+ if (input_scancode_to_scalar(ke, &scancode))
+ return -EINVAL;
+
+ mode = scancode >> 8;
+ if (mode > ATI_REMOTE2_PC)
+ return -EINVAL;
+
+ offset = ati_remote2_lookup(scancode & 0xff);
+ if (offset < 0)
+ return -EINVAL;
+
+ index = mode * ARRAY_SIZE(ati_remote2_key_table) + offset;
+ }
- mode = scancode >> 8;
- if (mode > ATI_REMOTE2_PC || !((1 << mode) & ar2->mode_mask))
- return -EINVAL;
+ ke->keycode = ar2->keycode[mode][offset];
+ ke->len = sizeof(scancode);
+ memcpy(&ke->scancode, &scancode, sizeof(scancode));
+ ke->index = index;
- index = ati_remote2_lookup(scancode & 0xFF);
- if (index < 0)
- return -EINVAL;
-
- *keycode = ar2->keycode[mode][index];
return 0;
}
static int ati_remote2_setkeycode(struct input_dev *idev,
- unsigned int scancode, unsigned int keycode)
+ const struct input_keymap_entry *ke,
+ unsigned int *old_keycode)
{
struct ati_remote2 *ar2 = input_get_drvdata(idev);
- unsigned int mode, old_keycode;
- int index;
-
- mode = scancode >> 8;
- if (mode > ATI_REMOTE2_PC || !((1 << mode) & ar2->mode_mask))
- return -EINVAL;
-
- index = ati_remote2_lookup(scancode & 0xFF);
- if (index < 0)
- return -EINVAL;
+ unsigned int mode;
+ int offset;
+ unsigned int index;
+ unsigned int scancode;
+
+ if (ke->flags & INPUT_KEYMAP_BY_INDEX) {
+ if (ke->index >= ATI_REMOTE2_MODES *
+ ARRAY_SIZE(ati_remote2_key_table))
+ return -EINVAL;
+
+ mode = ke->index / ARRAY_SIZE(ati_remote2_key_table);
+ offset = ke->index % ARRAY_SIZE(ati_remote2_key_table);
+ } else {
+ if (input_scancode_to_scalar(ke, &scancode))
+ return -EINVAL;
+
+ mode = scancode >> 8;
+ if (mode > ATI_REMOTE2_PC)
+ return -EINVAL;
+
+ offset = ati_remote2_lookup(scancode & 0xff);
+ if (offset < 0)
+ return -EINVAL;
+ }
- old_keycode = ar2->keycode[mode][index];
- ar2->keycode[mode][index] = keycode;
- __set_bit(keycode, idev->keybit);
+ *old_keycode = ar2->keycode[mode][offset];
+ ar2->keycode[mode][offset] = ke->keycode;
+ __set_bit(ke->keycode, idev->keybit);
for (mode = 0; mode < ATI_REMOTE2_MODES; mode++) {
for (index = 0; index < ARRAY_SIZE(ati_remote2_key_table); index++) {
- if (ar2->keycode[mode][index] == old_keycode)
+ if (ar2->keycode[mode][index] == *old_keycode)
return 0;
}
}
- __clear_bit(old_keycode, idev->keybit);
+ __clear_bit(*old_keycode, idev->keybit);
return 0;
}
idev->open = ati_remote2_open;
idev->close = ati_remote2_close;
- idev->getkeycode = ati_remote2_getkeycode;
- idev->setkeycode = ati_remote2_setkeycode;
+ idev->getkeycode_new = ati_remote2_getkeycode;
+ idev->setkeycode_new = ati_remote2_setkeycode;
idev->name = ar2->name;
idev->phys = ar2->phys;
pm->configcr = kmalloc(sizeof(*(pm->configcr)), GFP_KERNEL);
if (!pm->configcr)
- return -1;
+ return -ENOMEM;
return 0;
}
psmouse->private = etd = kzalloc(sizeof(struct elantech_data), GFP_KERNEL);
if (!etd)
- return -1;
+ return -ENOMEM;
etd->parity[0] = 1;
for (i = 1; i < 256; i++)
if (!new_dev)
return -ENOMEM;
- while (serio->child) {
+ while (!list_empty(&serio->children)) {
if (++retry > 3) {
printk(KERN_WARNING
- "psmouse: failed to destroy child port, "
+ "psmouse: failed to destroy children ports, "
"protocol change aborted.\n");
input_free_device(new_dev);
return -EIO;
return 0;
}
-static inline int synaptics_is_pt_packet(unsigned char *buf)
+static int synaptics_pt_start(struct serio *serio)
+{
+ struct psmouse *parent = serio_get_drvdata(serio->parent);
+ struct synaptics_data *priv = parent->private;
+
+ serio_pause_rx(parent->ps2dev.serio);
+ priv->pt_port = serio;
+ serio_continue_rx(parent->ps2dev.serio);
+
+ return 0;
+}
+
+static void synaptics_pt_stop(struct serio *serio)
+{
+ struct psmouse *parent = serio_get_drvdata(serio->parent);
+ struct synaptics_data *priv = parent->private;
+
+ serio_pause_rx(parent->ps2dev.serio);
+ priv->pt_port = NULL;
+ serio_continue_rx(parent->ps2dev.serio);
+}
+
+static int synaptics_is_pt_packet(unsigned char *buf)
{
return (buf[0] & 0xFC) == 0x84 && (buf[3] & 0xCC) == 0xC4;
}
static void synaptics_pt_activate(struct psmouse *psmouse)
{
- struct serio *ptport = psmouse->ps2dev.serio->child;
- struct psmouse *child = serio_get_drvdata(ptport);
struct synaptics_data *priv = psmouse->private;
+ struct psmouse *child = serio_get_drvdata(priv->pt_port);
/* adjust the touchpad to child's choice of protocol */
if (child) {
strlcpy(serio->name, "Synaptics pass-through", sizeof(serio->name));
strlcpy(serio->phys, "synaptics-pt/serio0", sizeof(serio->name));
serio->write = synaptics_pt_write;
+ serio->start = synaptics_pt_start;
+ serio->stop = synaptics_pt_stop;
serio->parent = psmouse->ps2dev.serio;
psmouse->pt_activate = synaptics_pt_activate;
if (unlikely(priv->pkt_type == SYN_NEWABS))
priv->pkt_type = synaptics_detect_pkt_type(psmouse);
- if (SYN_CAP_PASS_THROUGH(priv->capabilities) && synaptics_is_pt_packet(psmouse->packet)) {
- if (psmouse->ps2dev.serio->child)
- synaptics_pass_pt_packet(psmouse->ps2dev.serio->child, psmouse->packet);
+ if (SYN_CAP_PASS_THROUGH(priv->capabilities) &&
+ synaptics_is_pt_packet(psmouse->packet)) {
+ if (priv->pt_port)
+ synaptics_pass_pt_packet(priv->pt_port, psmouse->packet);
} else
synaptics_process_packet(psmouse);
psmouse->private = priv = kzalloc(sizeof(struct synaptics_data), GFP_KERNEL);
if (!priv)
- return -1;
+ return -ENOMEM;
psmouse_reset(psmouse);
unsigned char pkt_type; /* packet type - old, new, etc */
unsigned char mode; /* current mode byte */
int scroll;
+
+ struct serio *pt_port; /* Pass-through serio port */
};
void synaptics_module_init(void);
psmouse->private = kzalloc(sizeof(struct trackpoint_data), GFP_KERNEL);
if (!psmouse->private)
- return -1;
+ return -ENOMEM;
psmouse->vendor = "IBM";
psmouse->name = "TrackPoint";
spin_lock_init(&mousedev->client_lock);
mutex_init(&mousedev->mutex);
lockdep_set_subclass(&mousedev->mutex,
- minor == MOUSEDEV_MIX ? MOUSEDEV_MIX : 0);
+ minor == MOUSEDEV_MIX ? SINGLE_DEPTH_NESTING : 0);
init_waitqueue_head(&mousedev->wait);
if (minor == MOUSEDEV_MIX)
To compile this driver as a module, choose M here;
the module will be called ams_delta_serio.
+config SERIO_PS2MULT
+ tristate "TQC PS/2 multiplexer"
+ help
+ Say Y here if you have the PS/2 line multiplexer like the one
+ present on TQC boads.
+
+ To compile this driver as a module, choose M here: the
+ module will be called ps2mult.
+
endif
obj-$(CONFIG_HP_SDC) += hp_sdc.o
obj-$(CONFIG_HIL_MLC) += hp_sdc_mlc.o hil_mlc.o
obj-$(CONFIG_SERIO_PCIPS2) += pcips2.o
+obj-$(CONFIG_SERIO_PS2MULT) += ps2mult.o
obj-$(CONFIG_SERIO_MACEPS2) += maceps2.o
obj-$(CONFIG_SERIO_LIBPS2) += libps2.o
obj-$(CONFIG_SERIO_RAW) += serio_raw.o
#ifdef CONFIG_X86
static void i8042_dritek_enable(void)
{
- char param = 0x90;
+ unsigned char param = 0x90;
int error;
error = i8042_command(¶m, 0x1059);
--- /dev/null
+/*
+ * TQC PS/2 Multiplexer driver
+ *
+ * Copyright (C) 2010 Dmitry Eremin-Solenikov
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms of the GNU General Public License version 2 as published by
+ * the Free Software Foundation.
+ */
+
+
+#include <linux/kernel.h>
+#include <linux/slab.h>
+#include <linux/module.h>
+#include <linux/serio.h>
+
+MODULE_AUTHOR("Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>");
+MODULE_DESCRIPTION("TQC PS/2 Multiplexer driver");
+MODULE_LICENSE("GPL");
+
+#define PS2MULT_KB_SELECTOR 0xA0
+#define PS2MULT_MS_SELECTOR 0xA1
+#define PS2MULT_ESCAPE 0x7D
+#define PS2MULT_BSYNC 0x7E
+#define PS2MULT_SESSION_START 0x55
+#define PS2MULT_SESSION_END 0x56
+
+struct ps2mult_port {
+ struct serio *serio;
+ unsigned char sel;
+ bool registered;
+};
+
+#define PS2MULT_NUM_PORTS 2
+#define PS2MULT_KBD_PORT 0
+#define PS2MULT_MOUSE_PORT 1
+
+struct ps2mult {
+ struct serio *mx_serio;
+ struct ps2mult_port ports[PS2MULT_NUM_PORTS];
+
+ spinlock_t lock;
+ struct ps2mult_port *in_port;
+ struct ps2mult_port *out_port;
+ bool escape;
+};
+
+/* First MUST come PS2MULT_NUM_PORTS selectors */
+static const unsigned char ps2mult_controls[] = {
+ PS2MULT_KB_SELECTOR, PS2MULT_MS_SELECTOR,
+ PS2MULT_ESCAPE, PS2MULT_BSYNC,
+ PS2MULT_SESSION_START, PS2MULT_SESSION_END,
+};
+
+static const struct serio_device_id ps2mult_serio_ids[] = {
+ {
+ .type = SERIO_RS232,
+ .proto = SERIO_PS2MULT,
+ .id = SERIO_ANY,
+ .extra = SERIO_ANY,
+ },
+ { 0 }
+};
+
+MODULE_DEVICE_TABLE(serio, ps2mult_serio_ids);
+
+static void ps2mult_select_port(struct ps2mult *psm, struct ps2mult_port *port)
+{
+ struct serio *mx_serio = psm->mx_serio;
+
+ serio_write(mx_serio, port->sel);
+ psm->out_port = port;
+ dev_dbg(&mx_serio->dev, "switched to sel %02x\n", port->sel);
+}
+
+static int ps2mult_serio_write(struct serio *serio, unsigned char data)
+{
+ struct serio *mx_port = serio->parent;
+ struct ps2mult *psm = serio_get_drvdata(mx_port);
+ struct ps2mult_port *port = serio->port_data;
+ bool need_escape;
+ unsigned long flags;
+
+ spin_lock_irqsave(&psm->lock, flags);
+
+ if (psm->out_port != port)
+ ps2mult_select_port(psm, port);
+
+ need_escape = memchr(ps2mult_controls, data, sizeof(ps2mult_controls));
+
+ dev_dbg(&serio->dev,
+ "write: %s%02x\n", need_escape ? "ESC " : "", data);
+
+ if (need_escape)
+ serio_write(mx_port, PS2MULT_ESCAPE);
+
+ serio_write(mx_port, data);
+
+ spin_unlock_irqrestore(&psm->lock, flags);
+
+ return 0;
+}
+
+static int ps2mult_serio_start(struct serio *serio)
+{
+ struct ps2mult *psm = serio_get_drvdata(serio->parent);
+ struct ps2mult_port *port = serio->port_data;
+ unsigned long flags;
+
+ spin_lock_irqsave(&psm->lock, flags);
+ port->registered = true;
+ spin_unlock_irqrestore(&psm->lock, flags);
+
+ return 0;
+}
+
+static void ps2mult_serio_stop(struct serio *serio)
+{
+ struct ps2mult *psm = serio_get_drvdata(serio->parent);
+ struct ps2mult_port *port = serio->port_data;
+ unsigned long flags;
+
+ spin_lock_irqsave(&psm->lock, flags);
+ port->registered = false;
+ spin_unlock_irqrestore(&psm->lock, flags);
+}
+
+static int ps2mult_create_port(struct ps2mult *psm, int i)
+{
+ struct serio *mx_serio = psm->mx_serio;
+ struct serio *serio;
+
+ serio = kzalloc(sizeof(struct serio), GFP_KERNEL);
+ if (!serio)
+ return -ENOMEM;
+
+ strlcpy(serio->name, "TQC PS/2 Multiplexer", sizeof(serio->name));
+ snprintf(serio->phys, sizeof(serio->phys),
+ "%s/port%d", mx_serio->phys, i);
+ serio->id.type = SERIO_8042;
+ serio->write = ps2mult_serio_write;
+ serio->start = ps2mult_serio_start;
+ serio->stop = ps2mult_serio_stop;
+ serio->parent = psm->mx_serio;
+ serio->port_data = &psm->ports[i];
+
+ psm->ports[i].serio = serio;
+
+ return 0;
+}
+
+static void ps2mult_reset(struct ps2mult *psm)
+{
+ unsigned long flags;
+
+ spin_lock_irqsave(&psm->lock, flags);
+
+ serio_write(psm->mx_serio, PS2MULT_SESSION_END);
+ serio_write(psm->mx_serio, PS2MULT_SESSION_START);
+
+ ps2mult_select_port(psm, &psm->ports[PS2MULT_KBD_PORT]);
+
+ spin_unlock_irqrestore(&psm->lock, flags);
+}
+
+static int ps2mult_connect(struct serio *serio, struct serio_driver *drv)
+{
+ struct ps2mult *psm;
+ int i;
+ int error;
+
+ if (!serio->write)
+ return -EINVAL;
+
+ psm = kzalloc(sizeof(*psm), GFP_KERNEL);
+ if (!psm)
+ return -ENOMEM;
+
+ spin_lock_init(&psm->lock);
+ psm->mx_serio = serio;
+
+ for (i = 0; i < PS2MULT_NUM_PORTS; i++) {
+ psm->ports[i].sel = ps2mult_controls[i];
+ error = ps2mult_create_port(psm, i);
+ if (error)
+ goto err_out;
+ }
+
+ psm->in_port = psm->out_port = &psm->ports[PS2MULT_KBD_PORT];
+
+ serio_set_drvdata(serio, psm);
+ error = serio_open(serio, drv);
+ if (error)
+ goto err_out;
+
+ ps2mult_reset(psm);
+
+ for (i = 0; i < PS2MULT_NUM_PORTS; i++) {
+ struct serio *s = psm->ports[i].serio;
+
+ dev_info(&serio->dev, "%s port at %s\n", s->name, serio->phys);
+ serio_register_port(s);
+ }
+
+ return 0;
+
+err_out:
+ while (--i >= 0)
+ kfree(psm->ports[i].serio);
+ kfree(serio);
+ return error;
+}
+
+static void ps2mult_disconnect(struct serio *serio)
+{
+ struct ps2mult *psm = serio_get_drvdata(serio);
+
+ /* Note that serio core already take care of children ports */
+ serio_write(serio, PS2MULT_SESSION_END);
+ serio_close(serio);
+ kfree(psm);
+
+ serio_set_drvdata(serio, NULL);
+}
+
+static int ps2mult_reconnect(struct serio *serio)
+{
+ struct ps2mult *psm = serio_get_drvdata(serio);
+
+ ps2mult_reset(psm);
+
+ return 0;
+}
+
+static irqreturn_t ps2mult_interrupt(struct serio *serio,
+ unsigned char data, unsigned int dfl)
+{
+ struct ps2mult *psm = serio_get_drvdata(serio);
+ struct ps2mult_port *in_port;
+ unsigned long flags;
+
+ dev_dbg(&serio->dev, "Received %02x flags %02x\n", data, dfl);
+
+ spin_lock_irqsave(&psm->lock, flags);
+
+ if (psm->escape) {
+ psm->escape = false;
+ in_port = psm->in_port;
+ if (in_port->registered)
+ serio_interrupt(in_port->serio, data, dfl);
+ goto out;
+ }
+
+ switch (data) {
+ case PS2MULT_ESCAPE:
+ dev_dbg(&serio->dev, "ESCAPE\n");
+ psm->escape = true;
+ break;
+
+ case PS2MULT_BSYNC:
+ dev_dbg(&serio->dev, "BSYNC\n");
+ psm->in_port = psm->out_port;
+ break;
+
+ case PS2MULT_SESSION_START:
+ dev_dbg(&serio->dev, "SS\n");
+ break;
+
+ case PS2MULT_SESSION_END:
+ dev_dbg(&serio->dev, "SE\n");
+ break;
+
+ case PS2MULT_KB_SELECTOR:
+ dev_dbg(&serio->dev, "KB\n");
+ psm->in_port = &psm->ports[PS2MULT_KBD_PORT];
+ break;
+
+ case PS2MULT_MS_SELECTOR:
+ dev_dbg(&serio->dev, "MS\n");
+ psm->in_port = &psm->ports[PS2MULT_MOUSE_PORT];
+ break;
+
+ default:
+ in_port = psm->in_port;
+ if (in_port->registered)
+ serio_interrupt(in_port->serio, data, dfl);
+ break;
+ }
+
+ out:
+ spin_unlock_irqrestore(&psm->lock, flags);
+ return IRQ_HANDLED;
+}
+
+static struct serio_driver ps2mult_drv = {
+ .driver = {
+ .name = "ps2mult",
+ },
+ .description = "TQC PS/2 Multiplexer driver",
+ .id_table = ps2mult_serio_ids,
+ .interrupt = ps2mult_interrupt,
+ .connect = ps2mult_connect,
+ .disconnect = ps2mult_disconnect,
+ .reconnect = ps2mult_reconnect,
+};
+
+static int __init ps2mult_init(void)
+{
+ return serio_register_driver(&ps2mult_drv);
+}
+
+static void __exit ps2mult_exit(void)
+{
+ serio_unregister_driver(&ps2mult_drv);
+}
+
+module_init(ps2mult_init);
+module_exit(ps2mult_exit);
#include <linux/slab.h>
#include <linux/kthread.h>
#include <linux/mutex.h>
-#include <linux/freezer.h>
MODULE_AUTHOR("Vojtech Pavlik <vojtech@ucw.cz>");
MODULE_DESCRIPTION("Serio abstraction core");
static void serio_add_port(struct serio *serio);
static int serio_reconnect_port(struct serio *serio);
static void serio_disconnect_port(struct serio *serio);
-static void serio_reconnect_chain(struct serio *serio);
+static void serio_reconnect_subtree(struct serio *serio);
static void serio_attach_driver(struct serio_driver *drv);
static int serio_connect_driver(struct serio *serio, struct serio_driver *drv)
enum serio_event_type {
SERIO_RESCAN_PORT,
SERIO_RECONNECT_PORT,
- SERIO_RECONNECT_CHAIN,
+ SERIO_RECONNECT_SUBTREE,
SERIO_REGISTER_PORT,
SERIO_ATTACH_DRIVER,
};
serio_find_driver(event->object);
break;
- case SERIO_RECONNECT_CHAIN:
- serio_reconnect_chain(event->object);
+ case SERIO_RECONNECT_SUBTREE:
+ serio_reconnect_subtree(event->object);
break;
case SERIO_ATTACH_DRIVER:
}
/*
- * Destroy child serio port (if any) that has not been fully registered yet.
+ * Locate child serio port (if any) that has not been fully registered yet.
*
- * Note that we rely on the fact that port can have only one child and therefore
- * only one child registration request can be pending. Additionally, children
- * are registered by driver's connect() handler so there can't be a grandchild
- * pending registration together with a child.
+ * Children are registered by driver's connect() handler so there can't be a
+ * grandchild pending registration together with a child.
*/
static struct serio *serio_get_pending_child(struct serio *parent)
{
if (!strncmp(buf, "none", count)) {
serio_disconnect_port(serio);
} else if (!strncmp(buf, "reconnect", count)) {
- serio_reconnect_chain(serio);
+ serio_reconnect_subtree(serio);
} else if (!strncmp(buf, "rescan", count)) {
serio_disconnect_port(serio);
serio_find_driver(serio);
__module_get(THIS_MODULE);
INIT_LIST_HEAD(&serio->node);
+ INIT_LIST_HEAD(&serio->child_node);
+ INIT_LIST_HEAD(&serio->children);
spin_lock_init(&serio->lock);
mutex_init(&serio->drv_mutex);
device_initialize(&serio->dev);
*/
static void serio_add_port(struct serio *serio)
{
+ struct serio *parent = serio->parent;
int error;
- if (serio->parent) {
- serio_pause_rx(serio->parent);
- serio->parent->child = serio;
- serio_continue_rx(serio->parent);
+ if (parent) {
+ serio_pause_rx(parent);
+ list_add_tail(&serio->child_node, &parent->children);
+ serio_continue_rx(parent);
}
list_add_tail(&serio->node, &serio_list);
}
/*
- * serio_destroy_port() completes deregistration process and removes
+ * serio_destroy_port() completes unregistration process and removes
* port from the system
*/
static void serio_destroy_port(struct serio *serio)
{
struct serio *child;
- child = serio_get_pending_child(serio);
- if (child) {
+ while ((child = serio_get_pending_child(serio)) != NULL) {
serio_remove_pending_events(child);
put_device(&child->dev);
}
if (serio->parent) {
serio_pause_rx(serio->parent);
- serio->parent->child = NULL;
+ list_del_init(&serio->child_node);
serio_continue_rx(serio->parent);
serio->parent = NULL;
}
}
/*
- * Reconnect serio port and all its children (re-initialize attached devices)
+ * Reconnect serio port and all its children (re-initialize attached
+ * devices).
*/
-static void serio_reconnect_chain(struct serio *serio)
+static void serio_reconnect_subtree(struct serio *root)
{
+ struct serio *s = root;
+ int error;
+
do {
- if (serio_reconnect_port(serio)) {
- /* Ok, old children are now gone, we are done */
- break;
+ error = serio_reconnect_port(s);
+ if (!error) {
+ /*
+ * Reconnect was successful, move on to do the
+ * first child.
+ */
+ if (!list_empty(&s->children)) {
+ s = list_first_entry(&s->children,
+ struct serio, child_node);
+ continue;
+ }
}
- serio = serio->child;
- } while (serio);
+
+ /*
+ * Either it was a leaf node or reconnect failed and it
+ * became a leaf node. Continue reconnecting starting with
+ * the next sibling of the parent node.
+ */
+ while (s != root) {
+ struct serio *parent = s->parent;
+
+ if (!list_is_last(&s->child_node, &parent->children)) {
+ s = list_entry(s->child_node.next,
+ struct serio, child_node);
+ break;
+ }
+
+ s = parent;
+ }
+ } while (s != root);
}
/*
* serio_disconnect_port() unbinds a port from its driver. As a side effect
- * all child ports are unbound and destroyed.
+ * all children ports are unbound and destroyed.
*/
static void serio_disconnect_port(struct serio *serio)
{
- struct serio *s, *parent;
+ struct serio *s = serio;
+
+ /*
+ * Children ports should be disconnected and destroyed
+ * first; we travel the tree in depth-first order.
+ */
+ while (!list_empty(&serio->children)) {
+
+ /* Locate a leaf */
+ while (!list_empty(&s->children))
+ s = list_first_entry(&s->children,
+ struct serio, child_node);
- if (serio->child) {
/*
- * Children ports should be disconnected and destroyed
- * first, staring with the leaf one, since we don't want
- * to do recursion
+ * Prune this leaf node unless it is the one we
+ * started with.
*/
- for (s = serio; s->child; s = s->child)
- /* empty */;
-
- do {
- parent = s->parent;
+ if (s != serio) {
+ struct serio *parent = s->parent;
device_release_driver(&s->dev);
serio_destroy_port(s);
- } while ((s = parent) != serio);
+
+ s = parent;
+ }
}
/*
- * Ok, no children left, now disconnect this port
+ * OK, no children left, now disconnect this port.
*/
device_release_driver(&serio->dev);
}
void serio_reconnect(struct serio *serio)
{
- serio_queue_event(serio, NULL, SERIO_RECONNECT_CHAIN);
+ serio_queue_event(serio, NULL, SERIO_RECONNECT_SUBTREE);
}
EXPORT_SYMBOL(serio_reconnect);
EXPORT_SYMBOL(serio_unregister_port);
/*
- * Safely unregisters child port if one is present.
+ * Safely unregisters children ports if they are present.
*/
void serio_unregister_child_port(struct serio *serio)
{
+ struct serio *s, *next;
+
mutex_lock(&serio_mutex);
- if (serio->child) {
- serio_disconnect_port(serio->child);
- serio_destroy_port(serio->child);
+ list_for_each_entry_safe(s, next, &serio->children, child_node) {
+ serio_disconnect_port(s);
+ serio_destroy_port(s);
}
mutex_unlock(&serio_mutex);
}
MODULE_LICENSE("GPL v2");
MODULE_VERSION("0.1");
+static unsigned int sparse_keymap_get_key_index(struct input_dev *dev,
+ const struct key_entry *k)
+{
+ struct key_entry *key;
+ unsigned int idx = 0;
+
+ for (key = dev->keycode; key->type != KE_END; key++) {
+ if (key->type == KE_KEY) {
+ if (key == k)
+ break;
+ idx++;
+ }
+ }
+
+ return idx;
+}
+
+static struct key_entry *sparse_keymap_entry_by_index(struct input_dev *dev,
+ unsigned int index)
+{
+ struct key_entry *key;
+ unsigned int key_cnt = 0;
+
+ for (key = dev->keycode; key->type != KE_END; key++)
+ if (key->type == KE_KEY)
+ if (key_cnt++ == index)
+ return key;
+
+ return NULL;
+}
+
/**
* sparse_keymap_entry_from_scancode - perform sparse keymap lookup
* @dev: Input device using sparse keymap
}
EXPORT_SYMBOL(sparse_keymap_entry_from_keycode);
+static struct key_entry *sparse_keymap_locate(struct input_dev *dev,
+ const struct input_keymap_entry *ke)
+{
+ struct key_entry *key;
+ unsigned int scancode;
+
+ if (ke->flags & INPUT_KEYMAP_BY_INDEX)
+ key = sparse_keymap_entry_by_index(dev, ke->index);
+ else if (input_scancode_to_scalar(ke, &scancode) == 0)
+ key = sparse_keymap_entry_from_scancode(dev, scancode);
+ else
+ key = NULL;
+
+ return key;
+}
+
static int sparse_keymap_getkeycode(struct input_dev *dev,
- unsigned int scancode,
- unsigned int *keycode)
+ struct input_keymap_entry *ke)
{
const struct key_entry *key;
if (dev->keycode) {
- key = sparse_keymap_entry_from_scancode(dev, scancode);
+ key = sparse_keymap_locate(dev, ke);
if (key && key->type == KE_KEY) {
- *keycode = key->keycode;
+ ke->keycode = key->keycode;
+ if (!(ke->flags & INPUT_KEYMAP_BY_INDEX))
+ ke->index =
+ sparse_keymap_get_key_index(dev, key);
+ ke->len = sizeof(key->code);
+ memcpy(ke->scancode, &key->code, sizeof(key->code));
return 0;
}
}
}
static int sparse_keymap_setkeycode(struct input_dev *dev,
- unsigned int scancode,
- unsigned int keycode)
+ const struct input_keymap_entry *ke,
+ unsigned int *old_keycode)
{
struct key_entry *key;
- int old_keycode;
if (dev->keycode) {
- key = sparse_keymap_entry_from_scancode(dev, scancode);
+ key = sparse_keymap_locate(dev, ke);
if (key && key->type == KE_KEY) {
- old_keycode = key->keycode;
- key->keycode = keycode;
- set_bit(keycode, dev->keybit);
- if (!sparse_keymap_entry_from_keycode(dev, old_keycode))
- clear_bit(old_keycode, dev->keybit);
+ *old_keycode = key->keycode;
+ key->keycode = ke->keycode;
+ set_bit(ke->keycode, dev->keybit);
+ if (!sparse_keymap_entry_from_keycode(dev, *old_keycode))
+ clear_bit(*old_keycode, dev->keybit);
return 0;
}
}
dev->keycode = map;
dev->keycodemax = map_size;
- dev->getkeycode = sparse_keymap_getkeycode;
- dev->setkeycode = sparse_keymap_setkeycode;
+ dev->getkeycode_new = sparse_keymap_getkeycode;
+ dev->setkeycode_new = sparse_keymap_setkeycode;
return 0;
err_out:
kfree(map);
return error;
-
}
EXPORT_SYMBOL(sparse_keymap_setup);
To compile this driver as a module, choose M here: the
module will be called gtco.
+config TABLET_USB_HANWANG
+ tristate "Hanwang Art Master III tablet support (USB)"
+ depends on USB_ARCH_HAS_HCD
+ select USB
+ help
+ Say Y here if you want to use the USB version of the Hanwang Art
+ Master III tablet.
+
+ To compile this driver as a module, choose M here: the
+ module will be called hanwang.
+
config TABLET_USB_KBTAB
tristate "KB Gear JamStudio tablet support (USB)"
depends on USB_ARCH_HAS_HCD
obj-$(CONFIG_TABLET_USB_ACECAD) += acecad.o
obj-$(CONFIG_TABLET_USB_AIPTEK) += aiptek.o
obj-$(CONFIG_TABLET_USB_GTCO) += gtco.o
+obj-$(CONFIG_TABLET_USB_HANWANG) += hanwang.o
obj-$(CONFIG_TABLET_USB_KBTAB) += kbtab.o
obj-$(CONFIG_TABLET_USB_WACOM) += wacom.o
--- /dev/null
+/*
+ * USB Hanwang tablet support
+ *
+ * Copyright (c) 2010 Xing Wei <weixing@hanwang.com.cn>
+ *
+ */
+
+/*
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA
+ *
+ */
+
+#include <linux/types.h>
+#include <linux/kernel.h>
+#include <linux/slab.h>
+#include <linux/module.h>
+#include <linux/init.h>
+#include <linux/usb/input.h>
+
+#define DRIVER_AUTHOR "Xing Wei <weixing@hanwang.com.cn>"
+#define DRIVER_DESC "USB Hanwang tablet driver"
+#define DRIVER_LICENSE "GPL"
+
+MODULE_AUTHOR(DRIVER_AUTHOR);
+MODULE_DESCRIPTION(DRIVER_DESC);
+MODULE_LICENSE(DRIVER_LICENSE);
+
+#define USB_VENDOR_ID_HANWANG 0x0b57
+#define HANWANG_TABLET_INT_CLASS 0x0003
+#define HANWANG_TABLET_INT_SUB_CLASS 0x0001
+#define HANWANG_TABLET_INT_PROTOCOL 0x0002
+
+#define ART_MASTER_PKGLEN_MAX 10
+
+/* device IDs */
+#define STYLUS_DEVICE_ID 0x02
+#define TOUCH_DEVICE_ID 0x03
+#define CURSOR_DEVICE_ID 0x06
+#define ERASER_DEVICE_ID 0x0A
+#define PAD_DEVICE_ID 0x0F
+
+/* match vendor and interface info */
+#define HANWANG_TABLET_DEVICE(vend, cl, sc, pr) \
+ .match_flags = USB_DEVICE_ID_MATCH_VENDOR \
+ | USB_DEVICE_ID_MATCH_INT_INFO, \
+ .idVendor = (vend), \
+ .bInterfaceClass = (cl), \
+ .bInterfaceSubClass = (sc), \
+ .bInterfaceProtocol = (pr)
+
+enum hanwang_tablet_type {
+ HANWANG_ART_MASTER_III,
+ HANWANG_ART_MASTER_HD,
+};
+
+struct hanwang {
+ unsigned char *data;
+ dma_addr_t data_dma;
+ struct input_dev *dev;
+ struct usb_device *usbdev;
+ struct urb *irq;
+ const struct hanwang_features *features;
+ unsigned int current_tool;
+ unsigned int current_id;
+ char name[64];
+ char phys[32];
+};
+
+struct hanwang_features {
+ unsigned short pid;
+ char *name;
+ enum hanwang_tablet_type type;
+ int pkg_len;
+ int max_x;
+ int max_y;
+ int max_tilt_x;
+ int max_tilt_y;
+ int max_pressure;
+};
+
+static const struct hanwang_features features_array[] = {
+ { 0x8528, "Hanwang Art Master III 0906", HANWANG_ART_MASTER_III,
+ ART_MASTER_PKGLEN_MAX, 0x5757, 0x3692, 0x3f, 0x7f, 2048 },
+ { 0x8529, "Hanwang Art Master III 0604", HANWANG_ART_MASTER_III,
+ ART_MASTER_PKGLEN_MAX, 0x3d84, 0x2672, 0x3f, 0x7f, 2048 },
+ { 0x852a, "Hanwang Art Master III 1308", HANWANG_ART_MASTER_III,
+ ART_MASTER_PKGLEN_MAX, 0x7f00, 0x4f60, 0x3f, 0x7f, 2048 },
+ { 0x8401, "Hanwang Art Master HD 5012", HANWANG_ART_MASTER_HD,
+ ART_MASTER_PKGLEN_MAX, 0x678e, 0x4150, 0x3f, 0x7f, 1024 },
+};
+
+static const int hw_eventtypes[] = {
+ EV_KEY, EV_ABS, EV_MSC,
+};
+
+static const int hw_absevents[] = {
+ ABS_X, ABS_Y, ABS_TILT_X, ABS_TILT_Y, ABS_WHEEL,
+ ABS_RX, ABS_RY, ABS_PRESSURE, ABS_MISC,
+};
+
+static const int hw_btnevents[] = {
+ BTN_STYLUS, BTN_STYLUS2, BTN_TOOL_PEN, BTN_TOOL_RUBBER,
+ BTN_TOOL_MOUSE, BTN_TOOL_FINGER,
+ BTN_0, BTN_1, BTN_2, BTN_3, BTN_4, BTN_5, BTN_6, BTN_7, BTN_8,
+};
+
+static const int hw_mscevents[] = {
+ MSC_SERIAL,
+};
+
+static void hanwang_parse_packet(struct hanwang *hanwang)
+{
+ unsigned char *data = hanwang->data;
+ struct input_dev *input_dev = hanwang->dev;
+ struct usb_device *dev = hanwang->usbdev;
+ enum hanwang_tablet_type type = hanwang->features->type;
+ int i;
+ u16 x, y, p;
+
+ switch (data[0]) {
+ case 0x02: /* data packet */
+ switch (data[1]) {
+ case 0x80: /* tool prox out */
+ hanwang->current_id = 0;
+ input_report_key(input_dev, hanwang->current_tool, 0);
+ break;
+
+ case 0xc2: /* first time tool prox in */
+ switch (data[3] & 0xf0) {
+ case 0x20: /* art_master III */
+ case 0x30: /* art_master_HD */
+ hanwang->current_id = STYLUS_DEVICE_ID;
+ hanwang->current_tool = BTN_TOOL_PEN;
+ input_report_key(input_dev, BTN_TOOL_PEN, 1);
+ break;
+ case 0xa0: /* art_master III */
+ case 0xb0: /* art_master_HD */
+ hanwang->current_id = ERASER_DEVICE_ID;
+ hanwang->current_tool = BTN_TOOL_RUBBER;
+ input_report_key(input_dev, BTN_TOOL_RUBBER, 1);
+ break;
+ default:
+ hanwang->current_id = 0;
+ dev_dbg(&dev->dev,
+ "unknown tablet tool %02x ", data[0]);
+ break;
+ }
+ break;
+
+ default: /* tool data packet */
+ x = (data[2] << 8) | data[3];
+ y = (data[4] << 8) | data[5];
+
+ switch (type) {
+ case HANWANG_ART_MASTER_III:
+ p = (data[6] << 3) |
+ ((data[7] & 0xc0) >> 5) |
+ (data[1] & 0x01);
+ break;
+
+ case HANWANG_ART_MASTER_HD:
+ p = (data[7] >> 6) | (data[6] << 2);
+ break;
+
+ default:
+ p = 0;
+ break;
+ }
+
+ input_report_abs(input_dev, ABS_X,
+ le16_to_cpup((__le16 *)&x));
+ input_report_abs(input_dev, ABS_Y,
+ le16_to_cpup((__le16 *)&y));
+ input_report_abs(input_dev, ABS_PRESSURE,
+ le16_to_cpup((__le16 *)&p));
+ input_report_abs(input_dev, ABS_TILT_X, data[7] & 0x3f);
+ input_report_abs(input_dev, ABS_TILT_Y, data[8] & 0x7f);
+ input_report_key(input_dev, BTN_STYLUS, data[1] & 0x02);
+ input_report_key(input_dev, BTN_STYLUS2, data[1] & 0x04);
+ break;
+ }
+ input_report_abs(input_dev, ABS_MISC, hanwang->current_id);
+ input_event(input_dev, EV_MSC, MSC_SERIAL,
+ hanwang->features->pid);
+ break;
+
+ case 0x0c:
+ /* roll wheel */
+ hanwang->current_id = PAD_DEVICE_ID;
+
+ switch (type) {
+ case HANWANG_ART_MASTER_III:
+ input_report_key(input_dev, BTN_TOOL_FINGER, data[1] ||
+ data[2] || data[3]);
+ input_report_abs(input_dev, ABS_WHEEL, data[1]);
+ input_report_key(input_dev, BTN_0, data[2]);
+ for (i = 0; i < 8; i++)
+ input_report_key(input_dev,
+ BTN_1 + i, data[3] & (1 << i));
+ break;
+
+ case HANWANG_ART_MASTER_HD:
+ input_report_key(input_dev, BTN_TOOL_FINGER, data[1] ||
+ data[2] || data[3] || data[4] ||
+ data[5] || data[6]);
+ input_report_abs(input_dev, ABS_RX,
+ ((data[1] & 0x1f) << 8) | data[2]);
+ input_report_abs(input_dev, ABS_RY,
+ ((data[3] & 0x1f) << 8) | data[4]);
+ input_report_key(input_dev, BTN_0, data[5] & 0x01);
+ for (i = 0; i < 4; i++) {
+ input_report_key(input_dev,
+ BTN_1 + i, data[5] & (1 << i));
+ input_report_key(input_dev,
+ BTN_5 + i, data[6] & (1 << i));
+ }
+ break;
+ }
+
+ input_report_abs(input_dev, ABS_MISC, hanwang->current_id);
+ input_event(input_dev, EV_MSC, MSC_SERIAL, 0xffffffff);
+ break;
+
+ default:
+ dev_dbg(&dev->dev, "error packet %02x ", data[0]);
+ break;
+ }
+
+ input_sync(input_dev);
+}
+
+static void hanwang_irq(struct urb *urb)
+{
+ struct hanwang *hanwang = urb->context;
+ struct usb_device *dev = hanwang->usbdev;
+ int retval;
+
+ switch (urb->status) {
+ case 0:
+ /* success */;
+ hanwang_parse_packet(hanwang);
+ break;
+ case -ECONNRESET:
+ case -ENOENT:
+ case -ESHUTDOWN:
+ /* this urb is terminated, clean up */
+ dev_err(&dev->dev, "%s - urb shutting down with status: %d",
+ __func__, urb->status);
+ return;
+ default:
+ dev_err(&dev->dev, "%s - nonzero urb status received: %d",
+ __func__, urb->status);
+ break;
+ }
+
+ retval = usb_submit_urb(urb, GFP_ATOMIC);
+ if (retval)
+ dev_err(&dev->dev, "%s - usb_submit_urb failed with result %d",
+ __func__, retval);
+}
+
+static int hanwang_open(struct input_dev *dev)
+{
+ struct hanwang *hanwang = input_get_drvdata(dev);
+
+ hanwang->irq->dev = hanwang->usbdev;
+ if (usb_submit_urb(hanwang->irq, GFP_KERNEL))
+ return -EIO;
+
+ return 0;
+}
+
+static void hanwang_close(struct input_dev *dev)
+{
+ struct hanwang *hanwang = input_get_drvdata(dev);
+
+ usb_kill_urb(hanwang->irq);
+}
+
+static bool get_features(struct usb_device *dev, struct hanwang *hanwang)
+{
+ int i;
+
+ for (i = 0; i < ARRAY_SIZE(features_array); i++) {
+ if (le16_to_cpu(dev->descriptor.idProduct) ==
+ features_array[i].pid) {
+ hanwang->features = &features_array[i];
+ return true;
+ }
+ }
+
+ return false;
+}
+
+
+static int hanwang_probe(struct usb_interface *intf, const struct usb_device_id *id)
+{
+ struct usb_device *dev = interface_to_usbdev(intf);
+ struct usb_endpoint_descriptor *endpoint;
+ struct hanwang *hanwang;
+ struct input_dev *input_dev;
+ int error;
+ int i;
+
+ hanwang = kzalloc(sizeof(struct hanwang), GFP_KERNEL);
+ input_dev = input_allocate_device();
+ if (!hanwang || !input_dev) {
+ error = -ENOMEM;
+ goto fail1;
+ }
+
+ if (!get_features(dev, hanwang)) {
+ error = -ENXIO;
+ goto fail1;
+ }
+
+ hanwang->data = usb_alloc_coherent(dev, hanwang->features->pkg_len,
+ GFP_KERNEL, &hanwang->data_dma);
+ if (!hanwang->data) {
+ error = -ENOMEM;
+ goto fail1;
+ }
+
+ hanwang->irq = usb_alloc_urb(0, GFP_KERNEL);
+ if (!hanwang->irq) {
+ error = -ENOMEM;
+ goto fail2;
+ }
+
+ hanwang->usbdev = dev;
+ hanwang->dev = input_dev;
+
+ usb_make_path(dev, hanwang->phys, sizeof(hanwang->phys));
+ strlcat(hanwang->phys, "/input0", sizeof(hanwang->phys));
+
+ strlcpy(hanwang->name, hanwang->features->name, sizeof(hanwang->name));
+ input_dev->name = hanwang->name;
+ input_dev->phys = hanwang->phys;
+ usb_to_input_id(dev, &input_dev->id);
+ input_dev->dev.parent = &intf->dev;
+
+ input_set_drvdata(input_dev, hanwang);
+
+ input_dev->open = hanwang_open;
+ input_dev->close = hanwang_close;
+
+ for (i = 0; i < ARRAY_SIZE(hw_eventtypes); ++i)
+ __set_bit(hw_eventtypes[i], input_dev->evbit);
+
+ for (i = 0; i < ARRAY_SIZE(hw_absevents); ++i)
+ __set_bit(hw_absevents[i], input_dev->absbit);
+
+ for (i = 0; i < ARRAY_SIZE(hw_btnevents); ++i)
+ __set_bit(hw_btnevents[i], input_dev->keybit);
+
+ for (i = 0; i < ARRAY_SIZE(hw_mscevents); ++i)
+ __set_bit(hw_mscevents[i], input_dev->mscbit);
+
+ input_set_abs_params(input_dev, ABS_X,
+ 0, hanwang->features->max_x, 4, 0);
+ input_set_abs_params(input_dev, ABS_Y,
+ 0, hanwang->features->max_y, 4, 0);
+ input_set_abs_params(input_dev, ABS_TILT_X,
+ 0, hanwang->features->max_tilt_x, 0, 0);
+ input_set_abs_params(input_dev, ABS_TILT_Y,
+ 0, hanwang->features->max_tilt_y, 0, 0);
+ input_set_abs_params(input_dev, ABS_PRESSURE,
+ 0, hanwang->features->max_pressure, 0, 0);
+
+ endpoint = &intf->cur_altsetting->endpoint[0].desc;
+ usb_fill_int_urb(hanwang->irq, dev,
+ usb_rcvintpipe(dev, endpoint->bEndpointAddress),
+ hanwang->data, hanwang->features->pkg_len,
+ hanwang_irq, hanwang, endpoint->bInterval);
+ hanwang->irq->transfer_dma = hanwang->data_dma;
+ hanwang->irq->transfer_flags |= URB_NO_TRANSFER_DMA_MAP;
+
+ error = input_register_device(hanwang->dev);
+ if (error)
+ goto fail3;
+
+ usb_set_intfdata(intf, hanwang);
+
+ return 0;
+
+ fail3: usb_free_urb(hanwang->irq);
+ fail2: usb_free_coherent(dev, hanwang->features->pkg_len,
+ hanwang->data, hanwang->data_dma);
+ fail1: input_free_device(input_dev);
+ kfree(hanwang);
+ return error;
+
+}
+
+static void hanwang_disconnect(struct usb_interface *intf)
+{
+ struct hanwang *hanwang = usb_get_intfdata(intf);
+
+ input_unregister_device(hanwang->dev);
+ usb_free_urb(hanwang->irq);
+ usb_free_coherent(interface_to_usbdev(intf),
+ hanwang->features->pkg_len, hanwang->data,
+ hanwang->data_dma);
+ kfree(hanwang);
+ usb_set_intfdata(intf, NULL);
+}
+
+static const struct usb_device_id hanwang_ids[] = {
+ { HANWANG_TABLET_DEVICE(USB_VENDOR_ID_HANWANG, HANWANG_TABLET_INT_CLASS,
+ HANWANG_TABLET_INT_SUB_CLASS, HANWANG_TABLET_INT_PROTOCOL) },
+ {}
+};
+
+MODULE_DEVICE_TABLE(usb, hanwang_ids);
+
+static struct usb_driver hanwang_driver = {
+ .name = "hanwang",
+ .probe = hanwang_probe,
+ .disconnect = hanwang_disconnect,
+ .id_table = hanwang_ids,
+};
+
+static int __init hanwang_init(void)
+{
+ return usb_register(&hanwang_driver);
+}
+
+static void __exit hanwang_exit(void)
+{
+ usb_deregister(&hanwang_driver);
+}
+
+module_init(hanwang_init);
+module_exit(hanwang_exit);
extern const struct usb_device_id wacom_ids[];
void wacom_wac_irq(struct wacom_wac *wacom_wac, size_t len);
+void wacom_setup_device_quirks(struct wacom_features *features);
void wacom_setup_input_capabilities(struct input_dev *input_dev,
struct wacom_wac *wacom_wac);
#endif
out:
mutex_unlock(&wacom->lock);
- if (retval)
- usb_autopm_put_interface(wacom->intf);
+ usb_autopm_put_interface(wacom->intf);
return retval;
}
static void wacom_close(struct input_dev *dev)
{
struct wacom *wacom = input_get_drvdata(dev);
+ int autopm_error;
+
+ autopm_error = usb_autopm_get_interface(wacom->intf);
mutex_lock(&wacom->lock);
usb_kill_urb(wacom->irq);
wacom->intf->needs_remote_wakeup = 0;
mutex_unlock(&wacom->lock);
- usb_autopm_put_interface(wacom->intf);
+ if (!autopm_error)
+ usb_autopm_put_interface(wacom->intf);
}
static int wacom_parse_hid(struct usb_interface *intf, struct hid_descriptor *hid_desc,
features->pktlen = WACOM_PKGLEN_TPC2FG;
features->device_type = BTN_TOOL_TRIPLETAP;
}
- features->x_max =
- get_unaligned_le16(&report[i + 3]);
- features->x_phy =
- get_unaligned_le16(&report[i + 6]);
- features->unit = report[i + 9];
- features->unitExpo = report[i + 11];
- i += 12;
+ if (features->type == BAMBOO_PT) {
+ /* need to reset back */
+ features->pktlen = WACOM_PKGLEN_BBTOUCH;
+ features->device_type = BTN_TOOL_TRIPLETAP;
+ features->x_phy =
+ get_unaligned_le16(&report[i + 5]);
+ features->x_max =
+ get_unaligned_le16(&report[i + 8]);
+ i += 15;
+ } else {
+ features->x_max =
+ get_unaligned_le16(&report[i + 3]);
+ features->x_phy =
+ get_unaligned_le16(&report[i + 6]);
+ features->unit = report[i + 9];
+ features->unitExpo = report[i + 11];
+ i += 12;
+ }
} else if (pen) {
/* penabled only accepts exact bytes of data */
if (features->type == TABLETPC2FG)
features->pktlen = WACOM_PKGLEN_GRAPHIRE;
+ if (features->type == BAMBOO_PT)
+ features->pktlen = WACOM_PKGLEN_BBFUN;
features->device_type = BTN_TOOL_PEN;
features->x_max =
get_unaligned_le16(&report[i + 3]);
features->y_phy =
get_unaligned_le16(&report[i + 6]);
i += 7;
+ } else if (features->type == BAMBOO_PT) {
+ /* need to reset back */
+ features->pktlen = WACOM_PKGLEN_BBTOUCH;
+ features->device_type = BTN_TOOL_TRIPLETAP;
+ features->y_phy =
+ get_unaligned_le16(&report[i + 3]);
+ features->y_max =
+ get_unaligned_le16(&report[i + 6]);
+ i += 12;
} else {
features->y_max =
features->x_max;
/* penabled only accepts exact bytes of data */
if (features->type == TABLETPC2FG)
features->pktlen = WACOM_PKGLEN_GRAPHIRE;
+ if (features->type == BAMBOO_PT)
+ features->pktlen = WACOM_PKGLEN_BBFUN;
features->device_type = BTN_TOOL_PEN;
features->y_max =
get_unaligned_le16(&report[i + 3]);
if (!rep_data)
return error;
- /* ask to report tablet data if it is 2FGT or not a Tablet PC */
- if (features->device_type == BTN_TOOL_TRIPLETAP) {
+ /* ask to report tablet data if it is 2FGT Tablet PC or
+ * not a Tablet PC */
+ if (features->type == TABLETPC2FG) {
do {
rep_data[0] = 3;
rep_data[1] = 4;
WAC_HID_FEATURE_REPORT, report_id,
rep_data, 3);
} while ((error < 0 || rep_data[1] != 4) && limit++ < 5);
- } else if (features->type != TABLETPC && features->type != TABLETPC2FG) {
+ } else if (features->type != TABLETPC) {
do {
rep_data[0] = 2;
rep_data[1] = 2;
struct usb_host_interface *interface = intf->cur_altsetting;
struct hid_descriptor *hid_desc;
- /* default device to penabled */
+ /* default features */
features->device_type = BTN_TOOL_PEN;
-
- /* only Tablet PCs need to retrieve the info */
- if ((features->type != TABLETPC) && (features->type != TABLETPC2FG))
+ features->x_fuzz = 4;
+ features->y_fuzz = 4;
+ features->pressure_fuzz = 0;
+ features->distance_fuzz = 0;
+
+ /* only Tablet PCs and Bamboo P&T need to retrieve the info */
+ if ((features->type != TABLETPC) && (features->type != TABLETPC2FG) &&
+ (features->type != BAMBOO_PT))
goto out;
if (usb_get_extra_descriptor(interface, HID_DEVICET_HID, &hid_desc)) {
if (error)
goto out;
- /* touch device found but size is not defined. use default */
- if (features->device_type == BTN_TOOL_DOUBLETAP && !features->x_max) {
- features->x_max = 1023;
- features->y_max = 1023;
- }
-
out:
return error;
}
if (error)
goto fail2;
+ wacom_setup_device_quirks(features);
+
strlcpy(wacom_wac->name, features->name, sizeof(wacom_wac->name));
- if (features->type == TABLETPC || features->type == TABLETPC2FG) {
+ if (features->quirks & WACOM_QUIRK_MULTI_INPUT) {
/* Append the device type to the name */
strlcat(wacom_wac->name,
features->device_type == BTN_TOOL_PEN ?
return retval;
}
+static int wacom_bpt_touch(struct wacom_wac *wacom)
+{
+ struct wacom_features *features = &wacom->features;
+ struct input_dev *input = wacom->input;
+ unsigned char *data = wacom->data;
+ int sp = 0, sx = 0, sy = 0, count = 0;
+ int i;
+
+ for (i = 0; i < 2; i++) {
+ int p = data[9 * i + 2];
+ input_mt_slot(input, i);
+ /*
+ * Touch events need to be disabled while stylus is
+ * in proximity because user's hand is resting on touchpad
+ * and sending unwanted events. User expects tablet buttons
+ * to continue working though.
+ */
+ if (p && !wacom->shared->stylus_in_proximity) {
+ int x = get_unaligned_be16(&data[9 * i + 3]) & 0x7ff;
+ int y = get_unaligned_be16(&data[9 * i + 5]) & 0x7ff;
+ if (features->quirks & WACOM_QUIRK_BBTOUCH_LOWRES) {
+ x <<= 5;
+ y <<= 5;
+ }
+ input_report_abs(input, ABS_MT_PRESSURE, p);
+ input_report_abs(input, ABS_MT_POSITION_X, x);
+ input_report_abs(input, ABS_MT_POSITION_Y, y);
+ if (wacom->id[i] < 0)
+ wacom->id[i] = wacom->trk_id++ & MAX_TRACKING_ID;
+ if (!count++)
+ sp = p, sx = x, sy = y;
+ } else {
+ wacom->id[i] = -1;
+ }
+ input_report_abs(input, ABS_MT_TRACKING_ID, wacom->id[i]);
+ }
+
+ input_report_key(input, BTN_TOUCH, count > 0);
+ input_report_key(input, BTN_TOOL_FINGER, count == 1);
+ input_report_key(input, BTN_TOOL_DOUBLETAP, count == 2);
+
+ input_report_abs(input, ABS_PRESSURE, sp);
+ input_report_abs(input, ABS_X, sx);
+ input_report_abs(input, ABS_Y, sy);
+
+ input_report_key(input, BTN_LEFT, (data[1] & 0x08) != 0);
+ input_report_key(input, BTN_FORWARD, (data[1] & 0x04) != 0);
+ input_report_key(input, BTN_BACK, (data[1] & 0x02) != 0);
+ input_report_key(input, BTN_RIGHT, (data[1] & 0x01) != 0);
+
+ input_sync(input);
+
+ return 0;
+}
+
+static int wacom_bpt_pen(struct wacom_wac *wacom)
+{
+ struct input_dev *input = wacom->input;
+ unsigned char *data = wacom->data;
+ int prox = 0, x = 0, y = 0, p = 0, d = 0, pen = 0, btn1 = 0, btn2 = 0;
+
+ /*
+ * Similar to Graphire protocol, data[1] & 0x20 is proximity and
+ * data[1] & 0x18 is tool ID. 0x30 is safety check to ignore
+ * 2 unused tool ID's.
+ */
+ prox = (data[1] & 0x30) == 0x30;
+
+ /*
+ * All reports shared between PEN and RUBBER tool must be
+ * forced to a known starting value (zero) when transitioning to
+ * out-of-prox.
+ *
+ * If not reset then, to userspace, it will look like lost events
+ * if new tool comes in-prox with same values as previous tool sent.
+ *
+ * Hardware does report zero in most out-of-prox cases but not all.
+ */
+ if (prox) {
+ if (!wacom->shared->stylus_in_proximity) {
+ if (data[1] & 0x08) {
+ wacom->tool[0] = BTN_TOOL_RUBBER;
+ wacom->id[0] = ERASER_DEVICE_ID;
+ } else {
+ wacom->tool[0] = BTN_TOOL_PEN;
+ wacom->id[0] = STYLUS_DEVICE_ID;
+ }
+ wacom->shared->stylus_in_proximity = true;
+ }
+ x = le16_to_cpup((__le16 *)&data[2]);
+ y = le16_to_cpup((__le16 *)&data[4]);
+ p = le16_to_cpup((__le16 *)&data[6]);
+ d = data[8];
+ pen = data[1] & 0x01;
+ btn1 = data[1] & 0x02;
+ btn2 = data[1] & 0x04;
+ }
+
+ input_report_key(input, BTN_TOUCH, pen);
+ input_report_key(input, BTN_STYLUS, btn1);
+ input_report_key(input, BTN_STYLUS2, btn2);
+
+ input_report_abs(input, ABS_X, x);
+ input_report_abs(input, ABS_Y, y);
+ input_report_abs(input, ABS_PRESSURE, p);
+ input_report_abs(input, ABS_DISTANCE, d);
+
+ if (!prox) {
+ wacom->id[0] = 0;
+ wacom->shared->stylus_in_proximity = false;
+ }
+
+ input_report_key(input, wacom->tool[0], prox); /* PEN or RUBBER */
+ input_report_abs(input, ABS_MISC, wacom->id[0]); /* TOOL ID */
+
+ return 1;
+}
+
+static int wacom_bpt_irq(struct wacom_wac *wacom, size_t len)
+{
+ if (len == WACOM_PKGLEN_BBTOUCH)
+ return wacom_bpt_touch(wacom);
+ else if (len == WACOM_PKGLEN_BBFUN)
+ return wacom_bpt_pen(wacom);
+
+ return 0;
+}
+
void wacom_wac_irq(struct wacom_wac *wacom_wac, size_t len)
{
bool sync;
sync = wacom_tpc_irq(wacom_wac, len);
break;
+ case BAMBOO_PT:
+ sync = wacom_bpt_irq(wacom_wac, len);
+ break;
+
default:
sync = false;
break;
input_sync(wacom_wac->input);
}
-static void wacom_setup_intuos(struct wacom_wac *wacom_wac)
+static void wacom_setup_cintiq(struct wacom_wac *wacom_wac)
{
struct input_dev *input_dev = wacom_wac->input;
input_set_capability(input_dev, EV_MSC, MSC_SERIAL);
- input_set_capability(input_dev, EV_REL, REL_WHEEL);
-
- __set_bit(BTN_LEFT, input_dev->keybit);
- __set_bit(BTN_RIGHT, input_dev->keybit);
- __set_bit(BTN_MIDDLE, input_dev->keybit);
- __set_bit(BTN_SIDE, input_dev->keybit);
- __set_bit(BTN_EXTRA, input_dev->keybit);
__set_bit(BTN_TOOL_RUBBER, input_dev->keybit);
__set_bit(BTN_TOOL_PEN, input_dev->keybit);
- __set_bit(BTN_TOOL_MOUSE, input_dev->keybit);
__set_bit(BTN_TOOL_BRUSH, input_dev->keybit);
__set_bit(BTN_TOOL_PENCIL, input_dev->keybit);
__set_bit(BTN_TOOL_AIRBRUSH, input_dev->keybit);
- __set_bit(BTN_TOOL_LENS, input_dev->keybit);
__set_bit(BTN_STYLUS, input_dev->keybit);
__set_bit(BTN_STYLUS2, input_dev->keybit);
input_set_abs_params(input_dev, ABS_WHEEL, 0, 1023, 0, 0);
input_set_abs_params(input_dev, ABS_TILT_X, 0, 127, 0, 0);
input_set_abs_params(input_dev, ABS_TILT_Y, 0, 127, 0, 0);
+}
+
+static void wacom_setup_intuos(struct wacom_wac *wacom_wac)
+{
+ struct input_dev *input_dev = wacom_wac->input;
+
+ input_set_capability(input_dev, EV_REL, REL_WHEEL);
+
+ wacom_setup_cintiq(wacom_wac);
+
+ __set_bit(BTN_LEFT, input_dev->keybit);
+ __set_bit(BTN_RIGHT, input_dev->keybit);
+ __set_bit(BTN_MIDDLE, input_dev->keybit);
+ __set_bit(BTN_SIDE, input_dev->keybit);
+ __set_bit(BTN_EXTRA, input_dev->keybit);
+ __set_bit(BTN_TOOL_MOUSE, input_dev->keybit);
+ __set_bit(BTN_TOOL_LENS, input_dev->keybit);
+
input_set_abs_params(input_dev, ABS_RZ, -900, 899, 0, 0);
input_set_abs_params(input_dev, ABS_THROTTLE, -1023, 1023, 0, 0);
}
+void wacom_setup_device_quirks(struct wacom_features *features)
+{
+
+ /* touch device found but size is not defined. use default */
+ if (features->device_type == BTN_TOOL_DOUBLETAP && !features->x_max) {
+ features->x_max = 1023;
+ features->y_max = 1023;
+ }
+
+ /* these device have multiple inputs */
+ if (features->type == TABLETPC || features->type == TABLETPC2FG ||
+ features->type == BAMBOO_PT)
+ features->quirks |= WACOM_QUIRK_MULTI_INPUT;
+
+ /* quirks for bamboo touch */
+ if (features->type == BAMBOO_PT &&
+ features->device_type == BTN_TOOL_TRIPLETAP) {
+ features->x_max <<= 5;
+ features->y_max <<= 5;
+ features->x_fuzz <<= 5;
+ features->y_fuzz <<= 5;
+ features->pressure_max = 256;
+ features->pressure_fuzz = 16;
+ features->quirks |= WACOM_QUIRK_BBTOUCH_LOWRES;
+ }
+}
+
void wacom_setup_input_capabilities(struct input_dev *input_dev,
struct wacom_wac *wacom_wac)
{
__set_bit(BTN_TOUCH, input_dev->keybit);
- input_set_abs_params(input_dev, ABS_X, 0, features->x_max, 4, 0);
- input_set_abs_params(input_dev, ABS_Y, 0, features->y_max, 4, 0);
- input_set_abs_params(input_dev, ABS_PRESSURE, 0, features->pressure_max, 0, 0);
+ input_set_abs_params(input_dev, ABS_X, 0, features->x_max,
+ features->x_fuzz, 0);
+ input_set_abs_params(input_dev, ABS_Y, 0, features->y_max,
+ features->y_fuzz, 0);
+ input_set_abs_params(input_dev, ABS_PRESSURE, 0, features->pressure_max,
+ features->pressure_fuzz, 0);
__set_bit(ABS_MISC, input_dev->absbit);
__set_bit(BTN_9, input_dev->keybit);
/* fall through */
+ case CINTIQ:
+ for (i = 0; i < 8; i++)
+ __set_bit(BTN_0 + i, input_dev->keybit);
+ __set_bit(BTN_TOOL_FINGER, input_dev->keybit);
+
+ input_set_abs_params(input_dev, ABS_RX, 0, 4096, 0, 0);
+ input_set_abs_params(input_dev, ABS_RY, 0, 4096, 0, 0);
+ input_set_abs_params(input_dev, ABS_Z, -900, 899, 0, 0);
+ wacom_setup_cintiq(wacom_wac);
+ break;
+
case INTUOS3:
case INTUOS3L:
- case CINTIQ:
__set_bit(BTN_4, input_dev->keybit);
__set_bit(BTN_5, input_dev->keybit);
__set_bit(BTN_6, input_dev->keybit);
case PENPARTNER:
__set_bit(BTN_TOOL_RUBBER, input_dev->keybit);
break;
+
+ case BAMBOO_PT:
+ __clear_bit(ABS_MISC, input_dev->absbit);
+
+ if (features->device_type == BTN_TOOL_TRIPLETAP) {
+ __set_bit(BTN_LEFT, input_dev->keybit);
+ __set_bit(BTN_FORWARD, input_dev->keybit);
+ __set_bit(BTN_BACK, input_dev->keybit);
+ __set_bit(BTN_RIGHT, input_dev->keybit);
+
+ __set_bit(BTN_TOOL_FINGER, input_dev->keybit);
+ __set_bit(BTN_TOOL_DOUBLETAP, input_dev->keybit);
+
+ input_mt_create_slots(input_dev, 2);
+ input_set_abs_params(input_dev, ABS_MT_POSITION_X,
+ 0, features->x_max,
+ features->x_fuzz, 0);
+ input_set_abs_params(input_dev, ABS_MT_POSITION_Y,
+ 0, features->y_max,
+ features->y_fuzz, 0);
+ input_set_abs_params(input_dev, ABS_MT_PRESSURE,
+ 0, features->pressure_max,
+ features->pressure_fuzz, 0);
+ input_set_abs_params(input_dev, ABS_MT_TRACKING_ID, 0,
+ MAX_TRACKING_ID, 0, 0);
+ } else if (features->device_type == BTN_TOOL_PEN) {
+ __set_bit(BTN_TOOL_RUBBER, input_dev->keybit);
+ __set_bit(BTN_TOOL_PEN, input_dev->keybit);
+ __set_bit(BTN_STYLUS, input_dev->keybit);
+ __set_bit(BTN_STYLUS2, input_dev->keybit);
+ }
+ break;
}
}
{ "Wacom ISDv4 E3", WACOM_PKGLEN_TPC2FG, 26202, 16325, 255, 0, TABLETPC2FG };
static const struct wacom_features wacom_features_0x47 =
{ "Wacom Intuos2 6x8", WACOM_PKGLEN_INTUOS, 20320, 16240, 1023, 31, INTUOS };
+static struct wacom_features wacom_features_0xD0 =
+ { "Wacom Bamboo 2FG", WACOM_PKGLEN_BBFUN, 14720, 9200, 1023, 63, BAMBOO_PT };
+static struct wacom_features wacom_features_0xD1 =
+ { "Wacom Bamboo 2FG 4x5", WACOM_PKGLEN_BBFUN, 14720, 9200, 1023, 63, BAMBOO_PT };
+static struct wacom_features wacom_features_0xD2 =
+ { "Wacom Bamboo Craft", WACOM_PKGLEN_BBFUN, 14720, 9200, 1023, 63, BAMBOO_PT };
+static struct wacom_features wacom_features_0xD3 =
+ { "Wacom Bamboo 2FG 6x8", WACOM_PKGLEN_BBFUN, 21648, 13530, 1023, 63, BAMBOO_PT };
#define USB_DEVICE_WACOM(prod) \
USB_DEVICE(USB_VENDOR_ID_WACOM, prod), \
{ USB_DEVICE_WACOM(0xC6) },
{ USB_DEVICE_WACOM(0xC7) },
{ USB_DEVICE_WACOM(0xCE) },
+ { USB_DEVICE_WACOM(0xD0) },
+ { USB_DEVICE_WACOM(0xD1) },
+ { USB_DEVICE_WACOM(0xD2) },
+ { USB_DEVICE_WACOM(0xD3) },
{ USB_DEVICE_WACOM(0xF0) },
{ USB_DEVICE_WACOM(0xCC) },
{ USB_DEVICE_WACOM(0x90) },
#define WACOM_PKGLEN_INTUOS 10
#define WACOM_PKGLEN_TPC1FG 5
#define WACOM_PKGLEN_TPC2FG 14
+#define WACOM_PKGLEN_BBTOUCH 20
/* device IDs */
#define STYLUS_DEVICE_ID 0x02
#define WACOM_REPORT_TPC1FG 6
#define WACOM_REPORT_TPC2FG 13
+/* device quirks */
+#define WACOM_QUIRK_MULTI_INPUT 0x0001
+#define WACOM_QUIRK_BBTOUCH_LOWRES 0x0002
+
+/* largest reported tracking id */
+#define MAX_TRACKING_ID 0xfff
+
enum {
PENPARTNER = 0,
GRAPHIRE,
PTU,
PL,
DTU,
+ BAMBOO_PT,
INTUOS,
INTUOS3S,
INTUOS3,
int y_phy;
unsigned char unit;
unsigned char unitExpo;
+ int x_fuzz;
+ int y_fuzz;
+ int pressure_fuzz;
+ int distance_fuzz;
+ unsigned quirks;
};
struct wacom_shared {
int id[3];
__u32 serial[2];
int last_finger;
+ int trk_id;
struct wacom_features features;
struct wacom_shared *shared;
struct input_dev *input;
To compile this driver as a module, choose M here: the
module will be called h3600_ts_input.
+config TOUCHSCREEN_BU21013
+ tristate "BU21013 based touch panel controllers"
+ depends on I2C
+ help
+ Say Y here if you have a bu21013 touchscreen connected to
+ your system.
+
+ If unsure, say N.
+
+ To compile this driver as a module, choose M here: the
+ module will be called bu21013_ts.
+
config TOUCHSCREEN_CY8CTMG110
tristate "cy8ctmg110 touchscreen"
depends on I2C
To compile this driver as a module, choose M here: the
module will be called wacom_w8001.
+config TOUCHSCREEN_LPC32XX
+ tristate "LPC32XX touchscreen controller"
+ depends on ARCH_LPC32XX
+ help
+ Say Y here if you have a LPC32XX device and want
+ to support the built-in touchscreen.
+
+ To compile this driver as a module, choose M here: the
+ module will be called lpc32xx_ts.
+
config TOUCHSCREEN_MCS5000
tristate "MELFAS MCS-5000 touchscreen"
depends on I2C
To compile this driver as a module, choose M here: the
module will be called inexio.
+config TOUCHSCREEN_INTEL_MID
+ tristate "Intel MID platform resistive touchscreen"
+ depends on INTEL_SCU_IPC
+ help
+ Say Y here if you have a Intel MID based touchscreen in
+ your system.
+
+ If unsure, say N.
+
+ To compile this driver as a module, choose M here: the
+ module will be called intel_mid_touch.
+
config TOUCHSCREEN_MK712
tristate "ICS MicroClock MK712 touchscreen"
help
obj-$(CONFIG_TOUCHSCREEN_ADS7846) += ads7846.o
obj-$(CONFIG_TOUCHSCREEN_ATMEL_TSADCC) += atmel_tsadcc.o
obj-$(CONFIG_TOUCHSCREEN_BITSY) += h3600_ts_input.o
+obj-$(CONFIG_TOUCHSCREEN_BU21013) += bu21013_ts.o
obj-$(CONFIG_TOUCHSCREEN_CY8CTMG110) += cy8ctmg110_ts.o
obj-$(CONFIG_TOUCHSCREEN_DA9034) += da9034-ts.o
obj-$(CONFIG_TOUCHSCREEN_DYNAPRO) += dynapro.o
obj-$(CONFIG_TOUCHSCREEN_ELO) += elo.o
obj-$(CONFIG_TOUCHSCREEN_FUJITSU) += fujitsu_ts.o
obj-$(CONFIG_TOUCHSCREEN_INEXIO) += inexio.o
+obj-$(CONFIG_TOUCHSCREEN_INTEL_MID) += intel-mid-touch.o
+obj-$(CONFIG_TOUCHSCREEN_LPC32XX) += lpc32xx_ts.o
obj-$(CONFIG_TOUCHSCREEN_MC13783) += mc13783_ts.o
obj-$(CONFIG_TOUCHSCREEN_MCS5000) += mcs5000_ts.o
obj-$(CONFIG_TOUCHSCREEN_MIGOR) += migor_ts.o
struct spi_message msg;
struct mutex mutex;
- unsigned disabled:1; /* P: mutex */
- unsigned gpio3:1; /* P: mutex */
- unsigned gpio4:1; /* P: mutex */
+ bool disabled; /* P: mutex */
+ bool gpio3; /* P: mutex */
+ bool gpio4; /* P: mutex */
spinlock_t lock;
struct timer_list timer; /* P: lock */
- unsigned pending:1; /* P: lock */
/*
* DMA (thus cache coherency maintenance) requires the
u16 conversion_data[AD7877_NR_SENSE] ____cacheline_aligned;
};
-static int gpio3;
-module_param(gpio3, int, 0);
+static bool gpio3;
+module_param(gpio3, bool, 0);
MODULE_PARM_DESC(gpio3, "If gpio3 is set to 1 AUX3 acts as GPIO3");
/*
AD7877_READADD(reg));
req->xfer[0].tx_buf = &req->command;
req->xfer[0].len = 2;
+ req->xfer[0].cs_change = 1;
req->xfer[1].rx_buf = &req->sample;
req->xfer[1].len = 2;
req->xfer[0].tx_buf = &req->reset;
req->xfer[0].len = 2;
+ req->xfer[0].cs_change = 1;
req->xfer[1].tx_buf = &req->ref_on;
req->xfer[1].len = 2;
req->xfer[1].delay_usecs = ts->vref_delay_usecs;
+ req->xfer[1].cs_change = 1;
req->xfer[2].tx_buf = &req->command;
req->xfer[2].len = 2;
req->xfer[2].delay_usecs = ts->vref_delay_usecs;
+ req->xfer[2].cs_change = 1;
req->xfer[3].rx_buf = &req->sample;
req->xfer[3].len = 2;
+ req->xfer[3].cs_change = 1;
req->xfer[4].tx_buf = &ts->cmd_crtl2; /*REF OFF*/
req->xfer[4].len = 2;
+ req->xfer[4].cs_change = 1;
req->xfer[5].tx_buf = &ts->cmd_crtl1; /*DEFAULT*/
req->xfer[5].len = 2;
return status ? : sample;
}
-static void ad7877_rx(struct ad7877 *ts)
+static int ad7877_process_data(struct ad7877 *ts)
{
struct input_dev *input_dev = ts->input;
unsigned Rt;
Rt /= z1;
Rt = (Rt + 2047) >> 12;
+ /*
+ * Sample found inconsistent, pressure is beyond
+ * the maximum. Don't report it to user space.
+ */
+ if (Rt > ts->pressure_max)
+ return -EINVAL;
+
+ if (!timer_pending(&ts->timer))
+ input_report_key(input_dev, BTN_TOUCH, 1);
+
input_report_abs(input_dev, ABS_X, x);
input_report_abs(input_dev, ABS_Y, y);
input_report_abs(input_dev, ABS_PRESSURE, Rt);
input_sync(input_dev);
+
+ return 0;
}
+
+ return -EINVAL;
}
static inline void ad7877_ts_event_release(struct ad7877 *ts)
struct input_dev *input_dev = ts->input;
input_report_abs(input_dev, ABS_PRESSURE, 0);
+ input_report_key(input_dev, BTN_TOUCH, 0);
input_sync(input_dev);
}
static void ad7877_timer(unsigned long handle)
{
struct ad7877 *ts = (void *)handle;
+ unsigned long flags;
+ spin_lock_irqsave(&ts->lock, flags);
ad7877_ts_event_release(ts);
+ spin_unlock_irqrestore(&ts->lock, flags);
}
static irqreturn_t ad7877_irq(int irq, void *handle)
{
struct ad7877 *ts = handle;
unsigned long flags;
- int status;
+ int error;
- /*
- * The repeated conversion sequencer controlled by TMR kicked off
- * too fast. We ignore the last and process the sample sequence
- * currently in the queue. It can't be older than 9.4ms, and we
- * need to avoid that ts->msg doesn't get issued twice while in work.
- */
+ error = spi_sync(ts->spi, &ts->msg);
+ if (error) {
+ dev_err(&ts->spi->dev, "spi_sync --> %d\n", error);
+ goto out;
+ }
spin_lock_irqsave(&ts->lock, flags);
- if (!ts->pending) {
- ts->pending = 1;
-
- status = spi_async(ts->spi, &ts->msg);
- if (status)
- dev_err(&ts->spi->dev, "spi_sync --> %d\n", status);
- }
+ error = ad7877_process_data(ts);
+ if (!error)
+ mod_timer(&ts->timer, jiffies + TS_PEN_UP_TIMEOUT);
spin_unlock_irqrestore(&ts->lock, flags);
+out:
return IRQ_HANDLED;
}
-static void ad7877_callback(void *_ts)
-{
- struct ad7877 *ts = _ts;
-
- spin_lock_irq(&ts->lock);
-
- ad7877_rx(ts);
- ts->pending = 0;
- mod_timer(&ts->timer, jiffies + TS_PEN_UP_TIMEOUT);
-
- spin_unlock_irq(&ts->lock);
-}
-
static void ad7877_disable(struct ad7877 *ts)
{
mutex_lock(&ts->mutex);
if (!ts->disabled) {
- ts->disabled = 1;
+ ts->disabled = true;
disable_irq(ts->spi->irq);
- /* Wait for spi_async callback */
- while (ts->pending)
- msleep(1);
-
if (del_timer_sync(&ts->timer))
ad7877_ts_event_release(ts);
}
- /* we know the chip's in lowpower mode since we always
+ /*
+ * We know the chip's in lowpower mode since we always
* leave it that way after every request
*/
mutex_lock(&ts->mutex);
if (ts->disabled) {
- ts->disabled = 0;
+ ts->disabled = false;
enable_irq(ts->spi->irq);
}
#define SHOW(name) static ssize_t \
name ## _show(struct device *dev, struct device_attribute *attr, char *buf) \
{ \
- struct ad7877 *ts = dev_get_drvdata(dev); \
+ struct ad7877 *ts = dev_get_drvdata(dev); \
ssize_t v = ad7877_read_adc(ts->spi, \
AD7877_READ_CHAN(name)); \
if (v < 0) \
static ssize_t ad7877_disable_show(struct device *dev,
struct device_attribute *attr, char *buf)
{
- struct ad7877 *ts = dev_get_drvdata(dev);
+ struct ad7877 *ts = dev_get_drvdata(dev);
return sprintf(buf, "%u\n", ts->disabled);
}
static ssize_t ad7877_dac_show(struct device *dev,
struct device_attribute *attr, char *buf)
{
- struct ad7877 *ts = dev_get_drvdata(dev);
+ struct ad7877 *ts = dev_get_drvdata(dev);
return sprintf(buf, "%u\n", ts->dac);
}
static ssize_t ad7877_gpio3_show(struct device *dev,
struct device_attribute *attr, char *buf)
{
- struct ad7877 *ts = dev_get_drvdata(dev);
+ struct ad7877 *ts = dev_get_drvdata(dev);
return sprintf(buf, "%u\n", ts->gpio3);
}
static ssize_t ad7877_gpio4_show(struct device *dev,
struct device_attribute *attr, char *buf)
{
- struct ad7877 *ts = dev_get_drvdata(dev);
+ struct ad7877 *ts = dev_get_drvdata(dev);
return sprintf(buf, "%u\n", ts->gpio4);
}
&dev_attr_temp2.attr,
&dev_attr_aux1.attr,
&dev_attr_aux2.attr,
+ &dev_attr_aux3.attr,
&dev_attr_bat1.attr,
&dev_attr_bat2.attr,
&dev_attr_disable.attr,
&dev_attr_dac.attr,
+ &dev_attr_gpio3.attr,
&dev_attr_gpio4.attr,
NULL
};
+static mode_t ad7877_attr_is_visible(struct kobject *kobj,
+ struct attribute *attr, int n)
+{
+ mode_t mode = attr->mode;
+
+ if (attr == &dev_attr_aux3.attr) {
+ if (gpio3)
+ mode = 0;
+ } else if (attr == &dev_attr_gpio3.attr) {
+ if (!gpio3)
+ mode = 0;
+ }
+
+ return mode;
+}
+
static const struct attribute_group ad7877_attr_group = {
- .attrs = ad7877_attributes,
+ .is_visible = ad7877_attr_is_visible,
+ .attrs = ad7877_attributes,
};
static void ad7877_setup_ts_def_msg(struct spi_device *spi, struct ad7877 *ts)
spi_message_init(m);
- m->complete = ad7877_callback;
m->context = ts;
ts->xfer[0].tx_buf = &ts->cmd_crtl1;
ts->xfer[0].len = 2;
+ ts->xfer[0].cs_change = 1;
spi_message_add_tail(&ts->xfer[0], m);
ts->xfer[1].tx_buf = &ts->cmd_dummy; /* Send ZERO */
ts->xfer[1].len = 2;
+ ts->xfer[1].cs_change = 1;
spi_message_add_tail(&ts->xfer[1], m);
- for (i = 0; i < 11; i++) {
+ for (i = 0; i < AD7877_NR_SENSE; i++) {
ts->xfer[i + 2].rx_buf = &ts->conversion_data[AD7877_SEQ_YPOS + i];
ts->xfer[i + 2].len = 2;
+ if (i < (AD7877_NR_SENSE - 1))
+ ts->xfer[i + 2].cs_change = 1;
spi_message_add_tail(&ts->xfer[i + 2], m);
}
}
input_dev->phys = ts->phys;
input_dev->dev.parent = &spi->dev;
+ __set_bit(EV_KEY, input_dev->evbit);
+ __set_bit(BTN_TOUCH, input_dev->keybit);
__set_bit(EV_ABS, input_dev->evbit);
__set_bit(ABS_X, input_dev->absbit);
__set_bit(ABS_Y, input_dev->absbit);
/* Request AD7877 /DAV GPIO interrupt */
- err = request_irq(spi->irq, ad7877_irq, IRQF_TRIGGER_FALLING,
- spi->dev.driver->name, ts);
+ err = request_threaded_irq(spi->irq, NULL, ad7877_irq,
+ IRQF_TRIGGER_FALLING | IRQF_ONESHOT,
+ spi->dev.driver->name, ts);
if (err) {
dev_dbg(&spi->dev, "irq %d busy?\n", spi->irq);
goto err_free_mem;
if (err)
goto err_free_irq;
- err = device_create_file(&spi->dev,
- gpio3 ? &dev_attr_gpio3 : &dev_attr_aux3);
- if (err)
- goto err_remove_attr_group;
-
err = input_register_device(input_dev);
if (err)
- goto err_remove_attr;
+ goto err_remove_attr_group;
return 0;
-err_remove_attr:
- device_remove_file(&spi->dev,
- gpio3 ? &dev_attr_gpio3 : &dev_attr_aux3);
err_remove_attr_group:
sysfs_remove_group(&spi->dev.kobj, &ad7877_attr_group);
err_free_irq:
static int __devexit ad7877_remove(struct spi_device *spi)
{
- struct ad7877 *ts = dev_get_drvdata(&spi->dev);
+ struct ad7877 *ts = dev_get_drvdata(&spi->dev);
sysfs_remove_group(&spi->dev.kobj, &ad7877_attr_group);
- device_remove_file(&spi->dev,
- gpio3 ? &dev_attr_gpio3 : &dev_attr_aux3);
ad7877_disable(ts);
free_irq(ts->spi->irq, ts);
* it under the terms of the GNU General Public License version 2 as
* published by the Free Software Foundation.
*/
+#include <linux/types.h>
#include <linux/hwmon.h>
#include <linux/init.h>
#include <linux/err.h>
+#include <linux/sched.h>
#include <linux/delay.h>
#include <linux/input.h>
#include <linux/interrupt.h>
* files.
*/
-#define TS_POLL_DELAY (1 * 1000000) /* ns delay before the first sample */
-#define TS_POLL_PERIOD (5 * 1000000) /* ns delay between samples */
+#define TS_POLL_DELAY 1 /* ms delay before the first sample */
+#define TS_POLL_PERIOD 5 /* ms delay between samples */
/* this driver doesn't aim at the peak continuous sample rate */
#define SAMPLE_BITS (8 /*cmd*/ + 16 /*sample*/ + 2 /* before, after */)
struct ts_event {
- /* For portability, we can't read 12 bit values using SPI (which
- * would make the controller deliver them as native byteorder u16
+ /*
+ * For portability, we can't read 12 bit values using SPI (which
+ * would make the controller deliver them as native byte order u16
* with msbs zeroed). Instead, we read them as two 8-bit values,
* *** WHICH NEED BYTESWAPPING *** and range adjustment.
*/
u16 x;
u16 y;
u16 z1, z2;
- int ignore;
+ bool ignore;
u8 x_buf[3];
u8 y_buf[3];
};
struct spi_transfer xfer[18];
struct spi_message msg[5];
- struct spi_message *last_msg;
- int msg_idx;
+ int msg_count;
+ wait_queue_head_t wait;
+
+ bool pendown;
+
int read_cnt;
int read_rep;
int last_read;
u16 penirq_recheck_delay_usecs;
- spinlock_t lock;
- struct hrtimer timer;
- unsigned pendown:1; /* P: lock */
- unsigned pending:1; /* P: lock */
-// FIXME remove "irq_disabled"
- unsigned irq_disabled:1; /* P: lock */
- unsigned disabled:1;
- unsigned is_suspended:1;
+ struct mutex lock;
+ bool stopped; /* P: lock */
+ bool disabled; /* P: lock */
+ bool suspended; /* P: lock */
int (*filter)(void *data, int data_idx, int *val);
void *filter_data;
#define ADS_12_BIT (0 << 3)
#define ADS_SER (1 << 2) /* non-differential */
#define ADS_DFR (0 << 2) /* differential */
-#define ADS_PD10_PDOWN (0 << 0) /* lowpower mode + penirq */
+#define ADS_PD10_PDOWN (0 << 0) /* low power mode + penirq */
#define ADS_PD10_ADC_ON (1 << 0) /* ADC on */
#define ADS_PD10_REF_ON (2 << 0) /* vREF on + penirq */
#define ADS_PD10_ALL_ON (3 << 0) /* ADC + vREF on */
#define REF_ON (READ_12BIT_DFR(x, 1, 1))
#define REF_OFF (READ_12BIT_DFR(y, 0, 0))
+/* Must be called with ts->lock held */
+static void ads7846_stop(struct ads7846 *ts)
+{
+ if (!ts->disabled && !ts->suspended) {
+ /* Signal IRQ thread to stop polling and disable the handler. */
+ ts->stopped = true;
+ mb();
+ wake_up(&ts->wait);
+ disable_irq(ts->spi->irq);
+ }
+}
+
+/* Must be called with ts->lock held */
+static void ads7846_restart(struct ads7846 *ts)
+{
+ if (!ts->disabled && !ts->suspended) {
+ /* Tell IRQ thread that it may poll the device. */
+ ts->stopped = false;
+ mb();
+ enable_irq(ts->spi->irq);
+ }
+}
+
+/* Must be called with ts->lock held */
+static void __ads7846_disable(struct ads7846 *ts)
+{
+ ads7846_stop(ts);
+ regulator_disable(ts->reg);
+
+ /*
+ * We know the chip's in low power mode since we always
+ * leave it that way after every request
+ */
+}
+
+/* Must be called with ts->lock held */
+static void __ads7846_enable(struct ads7846 *ts)
+{
+ regulator_enable(ts->reg);
+ ads7846_restart(ts);
+}
+
+static void ads7846_disable(struct ads7846 *ts)
+{
+ mutex_lock(&ts->lock);
+
+ if (!ts->disabled) {
+
+ if (!ts->suspended)
+ __ads7846_disable(ts);
+
+ ts->disabled = true;
+ }
+
+ mutex_unlock(&ts->lock);
+}
+
+static void ads7846_enable(struct ads7846 *ts)
+{
+ mutex_lock(&ts->lock);
+
+ if (ts->disabled) {
+
+ ts->disabled = false;
+
+ if (!ts->suspended)
+ __ads7846_enable(ts);
+ }
+
+ mutex_unlock(&ts->lock);
+}
+
/*--------------------------------------------------------------------------*/
/*
struct spi_transfer xfer[2];
};
-static void ads7846_enable(struct ads7846 *ts);
-static void ads7846_disable(struct ads7846 *ts);
-
-static int device_suspended(struct device *dev)
-{
- struct ads7846 *ts = dev_get_drvdata(dev);
- return ts->is_suspended || ts->disabled;
-}
-
static int ads7846_read12_ser(struct device *dev, unsigned command)
{
- struct spi_device *spi = to_spi_device(dev);
- struct ads7846 *ts = dev_get_drvdata(dev);
- struct ser_req *req = kzalloc(sizeof *req, GFP_KERNEL);
- int status;
- int use_internal;
+ struct spi_device *spi = to_spi_device(dev);
+ struct ads7846 *ts = dev_get_drvdata(dev);
+ struct ser_req *req;
+ int status;
+ int use_internal;
+ req = kzalloc(sizeof *req, GFP_KERNEL);
if (!req)
return -ENOMEM;
CS_CHANGE(req->xfer[5]);
spi_message_add_tail(&req->xfer[5], &req->msg);
- ts->irq_disabled = 1;
- disable_irq(spi->irq);
+ mutex_lock(&ts->lock);
+ ads7846_stop(ts);
status = spi_sync(spi, &req->msg);
- ts->irq_disabled = 0;
- enable_irq(spi->irq);
+ ads7846_restart(ts);
+ mutex_unlock(&ts->lock);
if (status == 0) {
/* on-wire is a must-ignore bit, a BE12 value, then padding */
static int ads7845_read12_ser(struct device *dev, unsigned command)
{
- struct spi_device *spi = to_spi_device(dev);
- struct ads7846 *ts = dev_get_drvdata(dev);
- struct ads7845_ser_req *req = kzalloc(sizeof *req, GFP_KERNEL);
- int status;
+ struct spi_device *spi = to_spi_device(dev);
+ struct ads7846 *ts = dev_get_drvdata(dev);
+ struct ads7845_ser_req *req;
+ int status;
+ req = kzalloc(sizeof *req, GFP_KERNEL);
if (!req)
return -ENOMEM;
req->xfer[0].len = 3;
spi_message_add_tail(&req->xfer[0], &req->msg);
- ts->irq_disabled = 1;
- disable_irq(spi->irq);
+ mutex_lock(&ts->lock);
+ ads7846_stop(ts);
status = spi_sync(spi, &req->msg);
- ts->irq_disabled = 0;
- enable_irq(spi->irq);
+ ads7846_restart(ts);
+ mutex_unlock(&ts->lock);
if (status == 0) {
/* BE12 value, then padding */
/* external resistors may scale vAUX into 0..vREF */
retval *= ts->vref_mv;
retval = retval >> 12;
+
return retval;
}
/* ads7846 has a resistor ladder to scale this signal down */
if (ts->model == 7846)
retval *= 4;
+
return retval;
}
SHOW(in0_input, vaux, vaux_adjust)
SHOW(in1_input, vbatt, vbatt_adjust)
-
static struct attribute *ads7846_attributes[] = {
&dev_attr_temp0.attr,
&dev_attr_temp1.attr,
}
#endif
-static int is_pen_down(struct device *dev)
-{
- struct ads7846 *ts = dev_get_drvdata(dev);
-
- return ts->pendown;
-}
-
static ssize_t ads7846_pen_down_show(struct device *dev,
struct device_attribute *attr, char *buf)
{
- return sprintf(buf, "%u\n", is_pen_down(dev));
+ struct ads7846 *ts = dev_get_drvdata(dev);
+
+ return sprintf(buf, "%u\n", ts->pendown);
}
static DEVICE_ATTR(pen_down, S_IRUGO, ads7846_pen_down_show, NULL);
static ssize_t ads7846_disable_show(struct device *dev,
struct device_attribute *attr, char *buf)
{
- struct ads7846 *ts = dev_get_drvdata(dev);
+ struct ads7846 *ts = dev_get_drvdata(dev);
return sprintf(buf, "%u\n", ts->disabled);
}
if (strict_strtoul(buf, 10, &i))
return -EINVAL;
- spin_lock_irq(&ts->lock);
-
if (i)
ads7846_disable(ts);
else
ads7846_enable(ts);
- spin_unlock_irq(&ts->lock);
-
return count;
}
{
}
-/*
- * PENIRQ only kicks the timer. The timer only reissues the SPI transfer,
- * to retrieve touchscreen status.
- *
- * The SPI transfer completion callback does the real work. It reports
- * touchscreen events and reactivates the timer (or IRQ) as appropriate.
- */
+static int ads7846_debounce_filter(void *ads, int data_idx, int *val)
+{
+ struct ads7846 *ts = ads;
+
+ if (!ts->read_cnt || (abs(ts->last_read - *val) > ts->debounce_tol)) {
+ /* Start over collecting consistent readings. */
+ ts->read_rep = 0;
+ /*
+ * Repeat it, if this was the first read or the read
+ * wasn't consistent enough.
+ */
+ if (ts->read_cnt < ts->debounce_max) {
+ ts->last_read = *val;
+ ts->read_cnt++;
+ return ADS7846_FILTER_REPEAT;
+ } else {
+ /*
+ * Maximum number of debouncing reached and still
+ * not enough number of consistent readings. Abort
+ * the whole sample, repeat it in the next sampling
+ * period.
+ */
+ ts->read_cnt = 0;
+ return ADS7846_FILTER_IGNORE;
+ }
+ } else {
+ if (++ts->read_rep > ts->debounce_rep) {
+ /*
+ * Got a good reading for this coordinate,
+ * go for the next one.
+ */
+ ts->read_cnt = 0;
+ ts->read_rep = 0;
+ return ADS7846_FILTER_OK;
+ } else {
+ /* Read more values that are consistent. */
+ ts->read_cnt++;
+ return ADS7846_FILTER_REPEAT;
+ }
+ }
+}
+
+static int ads7846_no_filter(void *ads, int data_idx, int *val)
+{
+ return ADS7846_FILTER_OK;
+}
+
+static int ads7846_get_value(struct ads7846 *ts, struct spi_message *m)
+{
+ struct spi_transfer *t =
+ list_entry(m->transfers.prev, struct spi_transfer, transfer_list);
+
+ if (ts->model == 7845) {
+ return be16_to_cpup((__be16 *)&(((char*)t->rx_buf)[1])) >> 3;
+ } else {
+ /*
+ * adjust: on-wire is a must-ignore bit, a BE12 value, then
+ * padding; built from two 8 bit values written msb-first.
+ */
+ return be16_to_cpup((__be16 *)t->rx_buf) >> 3;
+ }
+}
+
+static void ads7846_update_value(struct spi_message *m, int val)
+{
+ struct spi_transfer *t =
+ list_entry(m->transfers.prev, struct spi_transfer, transfer_list);
+
+ *(u16 *)t->rx_buf = val;
+}
+
+static void ads7846_read_state(struct ads7846 *ts)
+{
+ struct ads7846_packet *packet = ts->packet;
+ struct spi_message *m;
+ int msg_idx = 0;
+ int val;
+ int action;
+ int error;
+
+ while (msg_idx < ts->msg_count) {
+
+ ts->wait_for_sync();
+
+ m = &ts->msg[msg_idx];
+ error = spi_sync(ts->spi, m);
+ if (error) {
+ dev_err(&ts->spi->dev, "spi_async --> %d\n", error);
+ packet->tc.ignore = true;
+ return;
+ }
+
+ /*
+ * Last message is power down request, no need to convert
+ * or filter the value.
+ */
+ if (msg_idx < ts->msg_count - 1) {
-static void ads7846_rx(void *ads)
+ val = ads7846_get_value(ts, m);
+
+ action = ts->filter(ts->filter_data, msg_idx, &val);
+ switch (action) {
+ case ADS7846_FILTER_REPEAT:
+ continue;
+
+ case ADS7846_FILTER_IGNORE:
+ packet->tc.ignore = true;
+ msg_idx = ts->msg_count - 1;
+ continue;
+
+ case ADS7846_FILTER_OK:
+ ads7846_update_value(m, val);
+ packet->tc.ignore = false;
+ msg_idx++;
+ break;
+
+ default:
+ BUG();
+ }
+ } else {
+ msg_idx++;
+ }
+ }
+}
+
+static void ads7846_report_state(struct ads7846 *ts)
{
- struct ads7846 *ts = ads;
- struct ads7846_packet *packet = ts->packet;
- unsigned Rt;
- u16 x, y, z1, z2;
+ struct ads7846_packet *packet = ts->packet;
+ unsigned int Rt;
+ u16 x, y, z1, z2;
- /* ads7846_rx_val() did in-place conversion (including byteswap) from
- * on-the-wire format as part of debouncing to get stable readings.
+ /*
+ * ads7846_get_value() does in-place conversion (including byte swap)
+ * from on-the-wire format as part of debouncing to get stable
+ * readings.
*/
if (ts->model == 7845) {
x = *(u16 *)packet->tc.x_buf;
Rt = 0;
}
- /* Sample found inconsistent by debouncing or pressure is beyond
+ /*
+ * Sample found inconsistent by debouncing or pressure is beyond
* the maximum. Don't report it to user space, repeat at least
* once more the measurement
*/
if (packet->tc.ignore || Rt > ts->pressure_max) {
dev_vdbg(&ts->spi->dev, "ignored %d pressure %d\n",
packet->tc.ignore, Rt);
- hrtimer_start(&ts->timer, ktime_set(0, TS_POLL_PERIOD),
- HRTIMER_MODE_REL);
return;
}
- /* Maybe check the pendown state before reporting. This discards
+ /*
+ * Maybe check the pendown state before reporting. This discards
* false readings when the pen is lifted.
*/
if (ts->penirq_recheck_delay_usecs) {
Rt = 0;
}
- /* NOTE: We can't rely on the pressure to determine the pen down
- * state, even this controller has a pressure sensor. The pressure
+ /*
+ * NOTE: We can't rely on the pressure to determine the pen down
+ * state, even this controller has a pressure sensor. The pressure
* value can fluctuate for quite a while after lifting the pen and
* in some cases may not even settle at the expected value.
*
if (Rt) {
struct input_dev *input = ts->input;
+ if (ts->swap_xy)
+ swap(x, y);
+
if (!ts->pendown) {
input_report_key(input, BTN_TOUCH, 1);
- ts->pendown = 1;
+ ts->pendown = true;
dev_vdbg(&ts->spi->dev, "DOWN\n");
}
- if (ts->swap_xy)
- swap(x, y);
-
input_report_abs(input, ABS_X, x);
input_report_abs(input, ABS_Y, y);
input_report_abs(input, ABS_PRESSURE, ts->pressure_max - Rt);
input_sync(input);
dev_vdbg(&ts->spi->dev, "%4d/%4d/%4d\n", x, y, Rt);
}
-
- hrtimer_start(&ts->timer, ktime_set(0, TS_POLL_PERIOD),
- HRTIMER_MODE_REL);
-}
-
-static int ads7846_debounce(void *ads, int data_idx, int *val)
-{
- struct ads7846 *ts = ads;
-
- if (!ts->read_cnt || (abs(ts->last_read - *val) > ts->debounce_tol)) {
- /* Start over collecting consistent readings. */
- ts->read_rep = 0;
- /* Repeat it, if this was the first read or the read
- * wasn't consistent enough. */
- if (ts->read_cnt < ts->debounce_max) {
- ts->last_read = *val;
- ts->read_cnt++;
- return ADS7846_FILTER_REPEAT;
- } else {
- /* Maximum number of debouncing reached and still
- * not enough number of consistent readings. Abort
- * the whole sample, repeat it in the next sampling
- * period.
- */
- ts->read_cnt = 0;
- return ADS7846_FILTER_IGNORE;
- }
- } else {
- if (++ts->read_rep > ts->debounce_rep) {
- /* Got a good reading for this coordinate,
- * go for the next one. */
- ts->read_cnt = 0;
- ts->read_rep = 0;
- return ADS7846_FILTER_OK;
- } else {
- /* Read more values that are consistent. */
- ts->read_cnt++;
- return ADS7846_FILTER_REPEAT;
- }
- }
}
-static int ads7846_no_filter(void *ads, int data_idx, int *val)
+static irqreturn_t ads7846_hard_irq(int irq, void *handle)
{
- return ADS7846_FILTER_OK;
-}
-
-static void ads7846_rx_val(void *ads)
-{
- struct ads7846 *ts = ads;
- struct ads7846_packet *packet = ts->packet;
- struct spi_message *m;
- struct spi_transfer *t;
- int val;
- int action;
- int status;
-
- m = &ts->msg[ts->msg_idx];
- t = list_entry(m->transfers.prev, struct spi_transfer, transfer_list);
-
- if (ts->model == 7845) {
- val = be16_to_cpup((__be16 *)&(((char*)t->rx_buf)[1])) >> 3;
- } else {
- /* adjust: on-wire is a must-ignore bit, a BE12 value, then
- * padding; built from two 8 bit values written msb-first.
- */
- val = be16_to_cpup((__be16 *)t->rx_buf) >> 3;
- }
+ struct ads7846 *ts = handle;
- action = ts->filter(ts->filter_data, ts->msg_idx, &val);
- switch (action) {
- case ADS7846_FILTER_REPEAT:
- break;
- case ADS7846_FILTER_IGNORE:
- packet->tc.ignore = 1;
- /* Last message will contain ads7846_rx() as the
- * completion function.
- */
- m = ts->last_msg;
- break;
- case ADS7846_FILTER_OK:
- *(u16 *)t->rx_buf = val;
- packet->tc.ignore = 0;
- m = &ts->msg[++ts->msg_idx];
- break;
- default:
- BUG();
- }
- ts->wait_for_sync();
- status = spi_async(ts->spi, m);
- if (status)
- dev_err(&ts->spi->dev, "spi_async --> %d\n",
- status);
+ return get_pendown_state(ts) ? IRQ_WAKE_THREAD : IRQ_HANDLED;
}
-static enum hrtimer_restart ads7846_timer(struct hrtimer *handle)
-{
- struct ads7846 *ts = container_of(handle, struct ads7846, timer);
- int status = 0;
-
- spin_lock(&ts->lock);
-
- if (unlikely(!get_pendown_state(ts) ||
- device_suspended(&ts->spi->dev))) {
- if (ts->pendown) {
- struct input_dev *input = ts->input;
-
- input_report_key(input, BTN_TOUCH, 0);
- input_report_abs(input, ABS_PRESSURE, 0);
- input_sync(input);
-
- ts->pendown = 0;
- dev_vdbg(&ts->spi->dev, "UP\n");
- }
-
- /* measurement cycle ended */
- if (!device_suspended(&ts->spi->dev)) {
- ts->irq_disabled = 0;
- enable_irq(ts->spi->irq);
- }
- ts->pending = 0;
- } else {
- /* pen is still down, continue with the measurement */
- ts->msg_idx = 0;
- ts->wait_for_sync();
- status = spi_async(ts->spi, &ts->msg[0]);
- if (status)
- dev_err(&ts->spi->dev, "spi_async --> %d\n", status);
- }
-
- spin_unlock(&ts->lock);
- return HRTIMER_NORESTART;
-}
static irqreturn_t ads7846_irq(int irq, void *handle)
{
struct ads7846 *ts = handle;
- unsigned long flags;
-
- spin_lock_irqsave(&ts->lock, flags);
- if (likely(get_pendown_state(ts))) {
- if (!ts->irq_disabled) {
- /* The ARM do_simple_IRQ() dispatcher doesn't act
- * like the other dispatchers: it will report IRQs
- * even after they've been disabled. We work around
- * that here. (The "generic irq" framework may help...)
- */
- ts->irq_disabled = 1;
- disable_irq_nosync(ts->spi->irq);
- ts->pending = 1;
- hrtimer_start(&ts->timer, ktime_set(0, TS_POLL_DELAY),
- HRTIMER_MODE_REL);
- }
- }
- spin_unlock_irqrestore(&ts->lock, flags);
- return IRQ_HANDLED;
-}
+ /* Start with a small delay before checking pendown state */
+ msleep(TS_POLL_DELAY);
-/*--------------------------------------------------------------------------*/
+ while (!ts->stopped && get_pendown_state(ts)) {
-/* Must be called with ts->lock held */
-static void ads7846_disable(struct ads7846 *ts)
-{
- if (ts->disabled)
- return;
+ /* pen is down, continue with the measurement */
+ ads7846_read_state(ts);
- ts->disabled = 1;
+ if (!ts->stopped)
+ ads7846_report_state(ts);
- /* are we waiting for IRQ, or polling? */
- if (!ts->pending) {
- ts->irq_disabled = 1;
- disable_irq(ts->spi->irq);
- } else {
- /* the timer will run at least once more, and
- * leave everything in a clean state, IRQ disabled
- */
- while (ts->pending) {
- spin_unlock_irq(&ts->lock);
- msleep(1);
- spin_lock_irq(&ts->lock);
- }
+ wait_event_timeout(ts->wait, ts->stopped,
+ msecs_to_jiffies(TS_POLL_PERIOD));
}
- regulator_disable(ts->reg);
-
- /* we know the chip's in lowpower mode since we always
- * leave it that way after every request
- */
-}
+ if (ts->pendown) {
+ struct input_dev *input = ts->input;
-/* Must be called with ts->lock held */
-static void ads7846_enable(struct ads7846 *ts)
-{
- if (!ts->disabled)
- return;
+ input_report_key(input, BTN_TOUCH, 0);
+ input_report_abs(input, ABS_PRESSURE, 0);
+ input_sync(input);
- regulator_enable(ts->reg);
+ ts->pendown = false;
+ dev_vdbg(&ts->spi->dev, "UP\n");
+ }
- ts->disabled = 0;
- ts->irq_disabled = 0;
- enable_irq(ts->spi->irq);
+ return IRQ_HANDLED;
}
static int ads7846_suspend(struct spi_device *spi, pm_message_t message)
{
struct ads7846 *ts = dev_get_drvdata(&spi->dev);
- spin_lock_irq(&ts->lock);
+ mutex_lock(&ts->lock);
- ts->is_suspended = 1;
- ads7846_disable(ts);
+ if (!ts->suspended) {
- spin_unlock_irq(&ts->lock);
+ if (!ts->disabled)
+ __ads7846_disable(ts);
- if (device_may_wakeup(&ts->spi->dev))
- enable_irq_wake(ts->spi->irq);
+ if (device_may_wakeup(&ts->spi->dev))
+ enable_irq_wake(ts->spi->irq);
- return 0;
+ ts->suspended = true;
+ }
+
+ mutex_unlock(&ts->lock);
+ return 0;
}
static int ads7846_resume(struct spi_device *spi)
{
struct ads7846 *ts = dev_get_drvdata(&spi->dev);
- if (device_may_wakeup(&ts->spi->dev))
- disable_irq_wake(ts->spi->irq);
+ mutex_lock(&ts->lock);
+
+ if (ts->suspended) {
- spin_lock_irq(&ts->lock);
+ ts->suspended = false;
- ts->is_suspended = 0;
- ads7846_enable(ts);
+ if (device_may_wakeup(&ts->spi->dev))
+ disable_irq_wake(ts->spi->irq);
- spin_unlock_irq(&ts->lock);
+ if (!ts->disabled)
+ __ads7846_enable(ts);
+ }
+
+ mutex_unlock(&ts->lock);
return 0;
}
-static int __devinit setup_pendown(struct spi_device *spi, struct ads7846 *ts)
+static int __devinit ads7846_setup_pendown(struct spi_device *spi, struct ads7846 *ts)
{
struct ads7846_platform_data *pdata = spi->dev.platform_data;
int err;
err = gpio_request(pdata->gpio_pendown, "ads7846_pendown");
if (err) {
dev_err(&spi->dev, "failed to request pendown GPIO%d\n",
- pdata->gpio_pendown);
+ pdata->gpio_pendown);
return err;
}
ts->gpio_pendown = pdata->gpio_pendown;
+
return 0;
}
-static int __devinit ads7846_probe(struct spi_device *spi)
+/*
+ * Set up the transfers to read touchscreen state; this assumes we
+ * use formula #2 for pressure, not #3.
+ */
+static void __devinit ads7846_setup_spi_msg(struct ads7846 *ts,
+ const struct ads7846_platform_data *pdata)
{
- struct ads7846 *ts;
- struct ads7846_packet *packet;
- struct input_dev *input_dev;
- const struct ads7846_platform_data *pdata = spi->dev.platform_data;
- struct spi_message *m;
- struct spi_transfer *x;
- unsigned long irq_flags;
- int vref;
- int err;
-
- if (!spi->irq) {
- dev_dbg(&spi->dev, "no IRQ?\n");
- return -ENODEV;
- }
-
- if (!pdata) {
- dev_dbg(&spi->dev, "no platform data?\n");
- return -ENODEV;
- }
-
- /* don't exceed max specified sample rate */
- if (spi->max_speed_hz > (125000 * SAMPLE_BITS)) {
- dev_dbg(&spi->dev, "f(sample) %d KHz?\n",
- (spi->max_speed_hz/SAMPLE_BITS)/1000);
- return -EINVAL;
- }
-
- /* We'd set TX wordsize 8 bits and RX wordsize to 13 bits ... except
- * that even if the hardware can do that, the SPI controller driver
- * may not. So we stick to very-portable 8 bit words, both RX and TX.
- */
- spi->bits_per_word = 8;
- spi->mode = SPI_MODE_0;
- err = spi_setup(spi);
- if (err < 0)
- return err;
-
- ts = kzalloc(sizeof(struct ads7846), GFP_KERNEL);
- packet = kzalloc(sizeof(struct ads7846_packet), GFP_KERNEL);
- input_dev = input_allocate_device();
- if (!ts || !packet || !input_dev) {
- err = -ENOMEM;
- goto err_free_mem;
- }
-
- dev_set_drvdata(&spi->dev, ts);
-
- ts->packet = packet;
- ts->spi = spi;
- ts->input = input_dev;
- ts->vref_mv = pdata->vref_mv;
- ts->swap_xy = pdata->swap_xy;
-
- hrtimer_init(&ts->timer, CLOCK_MONOTONIC, HRTIMER_MODE_REL);
- ts->timer.function = ads7846_timer;
-
- spin_lock_init(&ts->lock);
-
- ts->model = pdata->model ? : 7846;
- ts->vref_delay_usecs = pdata->vref_delay_usecs ? : 100;
- ts->x_plate_ohms = pdata->x_plate_ohms ? : 400;
- ts->pressure_max = pdata->pressure_max ? : ~0;
-
- if (pdata->filter != NULL) {
- if (pdata->filter_init != NULL) {
- err = pdata->filter_init(pdata, &ts->filter_data);
- if (err < 0)
- goto err_free_mem;
- }
- ts->filter = pdata->filter;
- ts->filter_cleanup = pdata->filter_cleanup;
- } else if (pdata->debounce_max) {
- ts->debounce_max = pdata->debounce_max;
- if (ts->debounce_max < 2)
- ts->debounce_max = 2;
- ts->debounce_tol = pdata->debounce_tol;
- ts->debounce_rep = pdata->debounce_rep;
- ts->filter = ads7846_debounce;
- ts->filter_data = ts;
- } else
- ts->filter = ads7846_no_filter;
-
- err = setup_pendown(spi, ts);
- if (err)
- goto err_cleanup_filter;
-
- if (pdata->penirq_recheck_delay_usecs)
- ts->penirq_recheck_delay_usecs =
- pdata->penirq_recheck_delay_usecs;
-
- ts->wait_for_sync = pdata->wait_for_sync ? : null_wait_for_sync;
-
- snprintf(ts->phys, sizeof(ts->phys), "%s/input0", dev_name(&spi->dev));
- snprintf(ts->name, sizeof(ts->name), "ADS%d Touchscreen", ts->model);
-
- input_dev->name = ts->name;
- input_dev->phys = ts->phys;
- input_dev->dev.parent = &spi->dev;
-
- input_dev->evbit[0] = BIT_MASK(EV_KEY) | BIT_MASK(EV_ABS);
- input_dev->keybit[BIT_WORD(BTN_TOUCH)] = BIT_MASK(BTN_TOUCH);
- input_set_abs_params(input_dev, ABS_X,
- pdata->x_min ? : 0,
- pdata->x_max ? : MAX_12BIT,
- 0, 0);
- input_set_abs_params(input_dev, ABS_Y,
- pdata->y_min ? : 0,
- pdata->y_max ? : MAX_12BIT,
- 0, 0);
- input_set_abs_params(input_dev, ABS_PRESSURE,
- pdata->pressure_min, pdata->pressure_max, 0, 0);
-
- vref = pdata->keep_vref_on;
+ struct spi_message *m = &ts->msg[0];
+ struct spi_transfer *x = ts->xfer;
+ struct ads7846_packet *packet = ts->packet;
+ int vref = pdata->keep_vref_on;
if (ts->model == 7873) {
- /* The AD7873 is almost identical to the ADS7846
+ /*
+ * The AD7873 is almost identical to the ADS7846
* keep VREF off during differential/ratiometric
- * conversion modes
+ * conversion modes.
*/
ts->model = 7846;
vref = 0;
}
- /* set up the transfers to read touchscreen state; this assumes we
- * use formula #2 for pressure, not #3.
- */
- m = &ts->msg[0];
- x = ts->xfer;
-
+ ts->msg_count = 1;
spi_message_init(m);
+ m->context = ts;
if (ts->model == 7845) {
packet->read_y_cmd[0] = READ_Y(vref);
spi_message_add_tail(x, m);
}
- /* the first sample after switching drivers can be low quality;
+ /*
+ * The first sample after switching drivers can be low quality;
* optionally discard it, using a second one after the signals
* have had enough time to stabilize.
*/
spi_message_add_tail(x, m);
}
- m->complete = ads7846_rx_val;
- m->context = ts;
-
+ ts->msg_count++;
m++;
spi_message_init(m);
+ m->context = ts;
if (ts->model == 7845) {
x++;
spi_message_add_tail(x, m);
}
- m->complete = ads7846_rx_val;
- m->context = ts;
-
/* turn y+ off, x- on; we'll use formula #2 */
if (ts->model == 7846) {
+ ts->msg_count++;
m++;
spi_message_init(m);
+ m->context = ts;
x++;
packet->read_z1 = READ_Z1(vref);
spi_message_add_tail(x, m);
}
- m->complete = ads7846_rx_val;
- m->context = ts;
-
+ ts->msg_count++;
m++;
spi_message_init(m);
+ m->context = ts;
x++;
packet->read_z2 = READ_Z2(vref);
x->len = 2;
spi_message_add_tail(x, m);
}
-
- m->complete = ads7846_rx_val;
- m->context = ts;
}
/* power down */
+ ts->msg_count++;
m++;
spi_message_init(m);
+ m->context = ts;
if (ts->model == 7845) {
x++;
CS_CHANGE(*x);
spi_message_add_tail(x, m);
+}
- m->complete = ads7846_rx;
- m->context = ts;
+static int __devinit ads7846_probe(struct spi_device *spi)
+{
+ struct ads7846 *ts;
+ struct ads7846_packet *packet;
+ struct input_dev *input_dev;
+ struct ads7846_platform_data *pdata = spi->dev.platform_data;
+ unsigned long irq_flags;
+ int err;
+
+ if (!spi->irq) {
+ dev_dbg(&spi->dev, "no IRQ?\n");
+ return -ENODEV;
+ }
+
+ if (!pdata) {
+ dev_dbg(&spi->dev, "no platform data?\n");
+ return -ENODEV;
+ }
+
+ /* don't exceed max specified sample rate */
+ if (spi->max_speed_hz > (125000 * SAMPLE_BITS)) {
+ dev_dbg(&spi->dev, "f(sample) %d KHz?\n",
+ (spi->max_speed_hz/SAMPLE_BITS)/1000);
+ return -EINVAL;
+ }
+
+ /* We'd set TX word size 8 bits and RX word size to 13 bits ... except
+ * that even if the hardware can do that, the SPI controller driver
+ * may not. So we stick to very-portable 8 bit words, both RX and TX.
+ */
+ spi->bits_per_word = 8;
+ spi->mode = SPI_MODE_0;
+ err = spi_setup(spi);
+ if (err < 0)
+ return err;
- ts->last_msg = m;
+ ts = kzalloc(sizeof(struct ads7846), GFP_KERNEL);
+ packet = kzalloc(sizeof(struct ads7846_packet), GFP_KERNEL);
+ input_dev = input_allocate_device();
+ if (!ts || !packet || !input_dev) {
+ err = -ENOMEM;
+ goto err_free_mem;
+ }
+
+ dev_set_drvdata(&spi->dev, ts);
+
+ ts->packet = packet;
+ ts->spi = spi;
+ ts->input = input_dev;
+ ts->vref_mv = pdata->vref_mv;
+ ts->swap_xy = pdata->swap_xy;
+
+ mutex_init(&ts->lock);
+ init_waitqueue_head(&ts->wait);
+
+ ts->model = pdata->model ? : 7846;
+ ts->vref_delay_usecs = pdata->vref_delay_usecs ? : 100;
+ ts->x_plate_ohms = pdata->x_plate_ohms ? : 400;
+ ts->pressure_max = pdata->pressure_max ? : ~0;
+
+ if (pdata->filter != NULL) {
+ if (pdata->filter_init != NULL) {
+ err = pdata->filter_init(pdata, &ts->filter_data);
+ if (err < 0)
+ goto err_free_mem;
+ }
+ ts->filter = pdata->filter;
+ ts->filter_cleanup = pdata->filter_cleanup;
+ } else if (pdata->debounce_max) {
+ ts->debounce_max = pdata->debounce_max;
+ if (ts->debounce_max < 2)
+ ts->debounce_max = 2;
+ ts->debounce_tol = pdata->debounce_tol;
+ ts->debounce_rep = pdata->debounce_rep;
+ ts->filter = ads7846_debounce_filter;
+ ts->filter_data = ts;
+ } else {
+ ts->filter = ads7846_no_filter;
+ }
+
+ err = ads7846_setup_pendown(spi, ts);
+ if (err)
+ goto err_cleanup_filter;
+
+ if (pdata->penirq_recheck_delay_usecs)
+ ts->penirq_recheck_delay_usecs =
+ pdata->penirq_recheck_delay_usecs;
+
+ ts->wait_for_sync = pdata->wait_for_sync ? : null_wait_for_sync;
+
+ snprintf(ts->phys, sizeof(ts->phys), "%s/input0", dev_name(&spi->dev));
+ snprintf(ts->name, sizeof(ts->name), "ADS%d Touchscreen", ts->model);
+
+ input_dev->name = ts->name;
+ input_dev->phys = ts->phys;
+ input_dev->dev.parent = &spi->dev;
+
+ input_dev->evbit[0] = BIT_MASK(EV_KEY) | BIT_MASK(EV_ABS);
+ input_dev->keybit[BIT_WORD(BTN_TOUCH)] = BIT_MASK(BTN_TOUCH);
+ input_set_abs_params(input_dev, ABS_X,
+ pdata->x_min ? : 0,
+ pdata->x_max ? : MAX_12BIT,
+ 0, 0);
+ input_set_abs_params(input_dev, ABS_Y,
+ pdata->y_min ? : 0,
+ pdata->y_max ? : MAX_12BIT,
+ 0, 0);
+ input_set_abs_params(input_dev, ABS_PRESSURE,
+ pdata->pressure_min, pdata->pressure_max, 0, 0);
+
+ ads7846_setup_spi_msg(ts, pdata);
ts->reg = regulator_get(&spi->dev, "vcc");
if (IS_ERR(ts->reg)) {
}
irq_flags = pdata->irq_flags ? : IRQF_TRIGGER_FALLING;
+ irq_flags |= IRQF_ONESHOT;
- err = request_irq(spi->irq, ads7846_irq, irq_flags,
- spi->dev.driver->name, ts);
-
+ err = request_threaded_irq(spi->irq, ads7846_hard_irq, ads7846_irq,
+ irq_flags, spi->dev.driver->name, ts);
if (err && !pdata->irq_flags) {
dev_info(&spi->dev,
"trying pin change workaround on irq %d\n", spi->irq);
- err = request_irq(spi->irq, ads7846_irq,
- IRQF_TRIGGER_FALLING | IRQF_TRIGGER_RISING,
- spi->dev.driver->name, ts);
+ irq_flags |= IRQF_TRIGGER_RISING;
+ err = request_threaded_irq(spi->irq,
+ ads7846_hard_irq, ads7846_irq,
+ irq_flags, spi->dev.driver->name, ts);
}
if (err) {
dev_info(&spi->dev, "touchscreen, irq %d\n", spi->irq);
- /* take a first sample, leaving nPENIRQ active and vREF off; avoid
+ /*
+ * Take a first sample, leaving nPENIRQ active and vREF off; avoid
* the touchscreen, in case it's not connected.
*/
if (ts->model == 7845)
static int __devexit ads7846_remove(struct spi_device *spi)
{
- struct ads7846 *ts = dev_get_drvdata(&spi->dev);
+ struct ads7846 *ts = dev_get_drvdata(&spi->dev);
device_init_wakeup(&spi->dev, false);
- ads784x_hwmon_unregister(spi, ts);
- input_unregister_device(ts->input);
-
- ads7846_suspend(spi, PMSG_SUSPEND);
-
sysfs_remove_group(&spi->dev.kobj, &ads784x_attr_group);
+ ads7846_disable(ts);
free_irq(ts->spi->irq, ts);
- /* suspend left the IRQ disabled */
- enable_irq(ts->spi->irq);
+
+ input_unregister_device(ts->input);
+
+ ads784x_hwmon_unregister(spi, ts);
regulator_disable(ts->reg);
regulator_put(ts->reg);
kfree(ts);
dev_dbg(&spi->dev, "unregistered touchscreen\n");
+
return 0;
}
--- /dev/null
+/*
+ * Copyright (C) ST-Ericsson SA 2010
+ * Author: Naveen Kumar G <naveen.gaddipati@stericsson.com> for ST-Ericsson
+ * License terms:GNU General Public License (GPL) version 2
+ */
+
+#include <linux/kernel.h>
+#include <linux/delay.h>
+#include <linux/interrupt.h>
+#include <linux/i2c.h>
+#include <linux/workqueue.h>
+#include <linux/input.h>
+#include <linux/input/bu21013.h>
+#include <linux/slab.h>
+
+#define PEN_DOWN_INTR 0
+#define MAX_FINGERS 2
+#define RESET_DELAY 30
+#define PENUP_TIMEOUT (10)
+#define DELTA_MIN 16
+#define MASK_BITS 0x03
+#define SHIFT_8 8
+#define SHIFT_2 2
+#define LENGTH_OF_BUFFER 11
+#define I2C_RETRY_COUNT 5
+
+#define BU21013_SENSORS_BTN_0_7_REG 0x70
+#define BU21013_SENSORS_BTN_8_15_REG 0x71
+#define BU21013_SENSORS_BTN_16_23_REG 0x72
+#define BU21013_X1_POS_MSB_REG 0x73
+#define BU21013_X1_POS_LSB_REG 0x74
+#define BU21013_Y1_POS_MSB_REG 0x75
+#define BU21013_Y1_POS_LSB_REG 0x76
+#define BU21013_X2_POS_MSB_REG 0x77
+#define BU21013_X2_POS_LSB_REG 0x78
+#define BU21013_Y2_POS_MSB_REG 0x79
+#define BU21013_Y2_POS_LSB_REG 0x7A
+#define BU21013_INT_CLR_REG 0xE8
+#define BU21013_INT_MODE_REG 0xE9
+#define BU21013_GAIN_REG 0xEA
+#define BU21013_OFFSET_MODE_REG 0xEB
+#define BU21013_XY_EDGE_REG 0xEC
+#define BU21013_RESET_REG 0xED
+#define BU21013_CALIB_REG 0xEE
+#define BU21013_DONE_REG 0xEF
+#define BU21013_SENSOR_0_7_REG 0xF0
+#define BU21013_SENSOR_8_15_REG 0xF1
+#define BU21013_SENSOR_16_23_REG 0xF2
+#define BU21013_POS_MODE1_REG 0xF3
+#define BU21013_POS_MODE2_REG 0xF4
+#define BU21013_CLK_MODE_REG 0xF5
+#define BU21013_IDLE_REG 0xFA
+#define BU21013_FILTER_REG 0xFB
+#define BU21013_TH_ON_REG 0xFC
+#define BU21013_TH_OFF_REG 0xFD
+
+
+#define BU21013_RESET_ENABLE 0x01
+
+#define BU21013_SENSORS_EN_0_7 0x3F
+#define BU21013_SENSORS_EN_8_15 0xFC
+#define BU21013_SENSORS_EN_16_23 0x1F
+
+#define BU21013_POS_MODE1_0 0x02
+#define BU21013_POS_MODE1_1 0x04
+#define BU21013_POS_MODE1_2 0x08
+
+#define BU21013_POS_MODE2_ZERO 0x01
+#define BU21013_POS_MODE2_AVG1 0x02
+#define BU21013_POS_MODE2_AVG2 0x04
+#define BU21013_POS_MODE2_EN_XY 0x08
+#define BU21013_POS_MODE2_EN_RAW 0x10
+#define BU21013_POS_MODE2_MULTI 0x80
+
+#define BU21013_CLK_MODE_DIV 0x01
+#define BU21013_CLK_MODE_EXT 0x02
+#define BU21013_CLK_MODE_CALIB 0x80
+
+#define BU21013_IDLET_0 0x01
+#define BU21013_IDLET_1 0x02
+#define BU21013_IDLET_2 0x04
+#define BU21013_IDLET_3 0x08
+#define BU21013_IDLE_INTERMIT_EN 0x10
+
+#define BU21013_DELTA_0_6 0x7F
+#define BU21013_FILTER_EN 0x80
+
+#define BU21013_INT_MODE_LEVEL 0x00
+#define BU21013_INT_MODE_EDGE 0x01
+
+#define BU21013_GAIN_0 0x01
+#define BU21013_GAIN_1 0x02
+#define BU21013_GAIN_2 0x04
+
+#define BU21013_OFFSET_MODE_DEFAULT 0x00
+#define BU21013_OFFSET_MODE_MOVE 0x01
+#define BU21013_OFFSET_MODE_DISABLE 0x02
+
+#define BU21013_TH_ON_0 0x01
+#define BU21013_TH_ON_1 0x02
+#define BU21013_TH_ON_2 0x04
+#define BU21013_TH_ON_3 0x08
+#define BU21013_TH_ON_4 0x10
+#define BU21013_TH_ON_5 0x20
+#define BU21013_TH_ON_6 0x40
+#define BU21013_TH_ON_7 0x80
+#define BU21013_TH_ON_MAX 0xFF
+
+#define BU21013_TH_OFF_0 0x01
+#define BU21013_TH_OFF_1 0x02
+#define BU21013_TH_OFF_2 0x04
+#define BU21013_TH_OFF_3 0x08
+#define BU21013_TH_OFF_4 0x10
+#define BU21013_TH_OFF_5 0x20
+#define BU21013_TH_OFF_6 0x40
+#define BU21013_TH_OFF_7 0x80
+#define BU21013_TH_OFF_MAX 0xFF
+
+#define BU21013_X_EDGE_0 0x01
+#define BU21013_X_EDGE_1 0x02
+#define BU21013_X_EDGE_2 0x04
+#define BU21013_X_EDGE_3 0x08
+#define BU21013_Y_EDGE_0 0x10
+#define BU21013_Y_EDGE_1 0x20
+#define BU21013_Y_EDGE_2 0x40
+#define BU21013_Y_EDGE_3 0x80
+
+#define BU21013_DONE 0x01
+#define BU21013_NUMBER_OF_X_SENSORS (6)
+#define BU21013_NUMBER_OF_Y_SENSORS (11)
+
+#define DRIVER_TP "bu21013_tp"
+
+/**
+ * struct bu21013_ts_data - touch panel data structure
+ * @client: pointer to the i2c client
+ * @wait: variable to wait_queue_head_t structure
+ * @touch_stopped: touch stop flag
+ * @chip: pointer to the touch panel controller
+ * @in_dev: pointer to the input device structure
+ * @intr_pin: interrupt pin value
+ *
+ * Touch panel device data structure
+ */
+struct bu21013_ts_data {
+ struct i2c_client *client;
+ wait_queue_head_t wait;
+ bool touch_stopped;
+ const struct bu21013_platform_device *chip;
+ struct input_dev *in_dev;
+ unsigned int intr_pin;
+};
+
+/**
+ * bu21013_read_block_data(): read the touch co-ordinates
+ * @data: bu21013_ts_data structure pointer
+ * @buf: byte pointer
+ *
+ * Read the touch co-ordinates using i2c read block into buffer
+ * and returns integer.
+ */
+static int bu21013_read_block_data(struct bu21013_ts_data *data, u8 *buf)
+{
+ int ret, i;
+
+ for (i = 0; i < I2C_RETRY_COUNT; i++) {
+ ret = i2c_smbus_read_i2c_block_data
+ (data->client, BU21013_SENSORS_BTN_0_7_REG,
+ LENGTH_OF_BUFFER, buf);
+ if (ret == LENGTH_OF_BUFFER)
+ return 0;
+ }
+ return -EINVAL;
+}
+
+/**
+ * bu21013_do_touch_report(): Get the touch co-ordinates
+ * @data: bu21013_ts_data structure pointer
+ *
+ * Get the touch co-ordinates from touch sensor registers and writes
+ * into device structure and returns integer.
+ */
+static int bu21013_do_touch_report(struct bu21013_ts_data *data)
+{
+ u8 buf[LENGTH_OF_BUFFER];
+ unsigned int pos_x[2], pos_y[2];
+ bool has_x_sensors, has_y_sensors;
+ int finger_down_count = 0;
+ int i;
+
+ if (data == NULL)
+ return -EINVAL;
+
+ if (bu21013_read_block_data(data, buf) < 0)
+ return -EINVAL;
+
+ has_x_sensors = hweight32(buf[0] & BU21013_SENSORS_EN_0_7);
+ has_y_sensors = hweight32(((buf[1] & BU21013_SENSORS_EN_8_15) |
+ ((buf[2] & BU21013_SENSORS_EN_16_23) << SHIFT_8)) >> SHIFT_2);
+ if (!has_x_sensors || !has_y_sensors)
+ return 0;
+
+ for (i = 0; i < MAX_FINGERS; i++) {
+ const u8 *p = &buf[4 * i + 3];
+ unsigned int x = p[0] << SHIFT_2 | (p[1] & MASK_BITS);
+ unsigned int y = p[2] << SHIFT_2 | (p[3] & MASK_BITS);
+ if (x == 0 || y == 0)
+ continue;
+ pos_x[finger_down_count] = x;
+ pos_y[finger_down_count] = y;
+ finger_down_count++;
+ }
+
+ if (finger_down_count) {
+ if (finger_down_count == 2 &&
+ (abs(pos_x[0] - pos_x[1]) < DELTA_MIN ||
+ abs(pos_y[0] - pos_y[1]) < DELTA_MIN)) {
+ return 0;
+ }
+
+ for (i = 0; i < finger_down_count; i++) {
+ if (data->chip->x_flip)
+ pos_x[i] = data->chip->touch_x_max - pos_x[i];
+ if (data->chip->y_flip)
+ pos_y[i] = data->chip->touch_y_max - pos_y[i];
+
+ input_report_abs(data->in_dev,
+ ABS_MT_POSITION_X, pos_x[i]);
+ input_report_abs(data->in_dev,
+ ABS_MT_POSITION_Y, pos_y[i]);
+ input_mt_sync(data->in_dev);
+ }
+ } else
+ input_mt_sync(data->in_dev);
+
+ input_sync(data->in_dev);
+
+ return 0;
+}
+/**
+ * bu21013_gpio_irq() - gpio thread function for touch interrupt
+ * @irq: irq value
+ * @device_data: void pointer
+ *
+ * This gpio thread function for touch interrupt
+ * and returns irqreturn_t.
+ */
+static irqreturn_t bu21013_gpio_irq(int irq, void *device_data)
+{
+ struct bu21013_ts_data *data = device_data;
+ struct i2c_client *i2c = data->client;
+ int retval;
+
+ do {
+ retval = bu21013_do_touch_report(data);
+ if (retval < 0) {
+ dev_err(&i2c->dev, "bu21013_do_touch_report failed\n");
+ return IRQ_NONE;
+ }
+
+ data->intr_pin = data->chip->irq_read_val();
+ if (data->intr_pin == PEN_DOWN_INTR)
+ wait_event_timeout(data->wait, data->touch_stopped,
+ msecs_to_jiffies(2));
+ } while (!data->intr_pin && !data->touch_stopped);
+
+ return IRQ_HANDLED;
+}
+
+/**
+ * bu21013_init_chip() - power on sequence for the bu21013 controller
+ * @data: device structure pointer
+ *
+ * This function is used to power on
+ * the bu21013 controller and returns integer.
+ */
+static int bu21013_init_chip(struct bu21013_ts_data *data)
+{
+ int retval;
+ struct i2c_client *i2c = data->client;
+
+ retval = i2c_smbus_write_byte_data(i2c, BU21013_RESET_REG,
+ BU21013_RESET_ENABLE);
+ if (retval < 0) {
+ dev_err(&i2c->dev, "BU21013_RESET reg write failed\n");
+ return retval;
+ }
+ msleep(RESET_DELAY);
+
+ retval = i2c_smbus_write_byte_data(i2c, BU21013_SENSOR_0_7_REG,
+ BU21013_SENSORS_EN_0_7);
+ if (retval < 0) {
+ dev_err(&i2c->dev, "BU21013_SENSOR_0_7 reg write failed\n");
+ return retval;
+ }
+
+ retval = i2c_smbus_write_byte_data(i2c, BU21013_SENSOR_8_15_REG,
+ BU21013_SENSORS_EN_8_15);
+ if (retval < 0) {
+ dev_err(&i2c->dev, "BU21013_SENSOR_8_15 reg write failed\n");
+ return retval;
+ }
+
+ retval = i2c_smbus_write_byte_data(i2c, BU21013_SENSOR_16_23_REG,
+ BU21013_SENSORS_EN_16_23);
+ if (retval < 0) {
+ dev_err(&i2c->dev, "BU21013_SENSOR_16_23 reg write failed\n");
+ return retval;
+ }
+
+ retval = i2c_smbus_write_byte_data(i2c, BU21013_POS_MODE1_REG,
+ (BU21013_POS_MODE1_0 | BU21013_POS_MODE1_1));
+ if (retval < 0) {
+ dev_err(&i2c->dev, "BU21013_POS_MODE1 reg write failed\n");
+ return retval;
+ }
+
+ retval = i2c_smbus_write_byte_data(i2c, BU21013_POS_MODE2_REG,
+ (BU21013_POS_MODE2_ZERO | BU21013_POS_MODE2_AVG1 |
+ BU21013_POS_MODE2_AVG2 | BU21013_POS_MODE2_EN_RAW |
+ BU21013_POS_MODE2_MULTI));
+ if (retval < 0) {
+ dev_err(&i2c->dev, "BU21013_POS_MODE2 reg write failed\n");
+ return retval;
+ }
+
+ if (data->chip->ext_clk)
+ retval = i2c_smbus_write_byte_data(i2c, BU21013_CLK_MODE_REG,
+ (BU21013_CLK_MODE_EXT | BU21013_CLK_MODE_CALIB));
+ else
+ retval = i2c_smbus_write_byte_data(i2c, BU21013_CLK_MODE_REG,
+ (BU21013_CLK_MODE_DIV | BU21013_CLK_MODE_CALIB));
+ if (retval < 0) {
+ dev_err(&i2c->dev, "BU21013_CLK_MODE reg write failed\n");
+ return retval;
+ }
+
+ retval = i2c_smbus_write_byte_data(i2c, BU21013_IDLE_REG,
+ (BU21013_IDLET_0 | BU21013_IDLE_INTERMIT_EN));
+ if (retval < 0) {
+ dev_err(&i2c->dev, "BU21013_IDLE reg write failed\n");
+ return retval;
+ }
+
+ retval = i2c_smbus_write_byte_data(i2c, BU21013_INT_MODE_REG,
+ BU21013_INT_MODE_LEVEL);
+ if (retval < 0) {
+ dev_err(&i2c->dev, "BU21013_INT_MODE reg write failed\n");
+ return retval;
+ }
+
+ retval = i2c_smbus_write_byte_data(i2c, BU21013_FILTER_REG,
+ (BU21013_DELTA_0_6 |
+ BU21013_FILTER_EN));
+ if (retval < 0) {
+ dev_err(&i2c->dev, "BU21013_FILTER reg write failed\n");
+ return retval;
+ }
+
+ retval = i2c_smbus_write_byte_data(i2c, BU21013_TH_ON_REG,
+ BU21013_TH_ON_5);
+ if (retval < 0) {
+ dev_err(&i2c->dev, "BU21013_TH_ON reg write failed\n");
+ return retval;
+ }
+
+ retval = i2c_smbus_write_byte_data(i2c, BU21013_TH_OFF_REG,
+ BU21013_TH_OFF_4 || BU21013_TH_OFF_3);
+ if (retval < 0) {
+ dev_err(&i2c->dev, "BU21013_TH_OFF reg write failed\n");
+ return retval;
+ }
+
+ retval = i2c_smbus_write_byte_data(i2c, BU21013_GAIN_REG,
+ (BU21013_GAIN_0 | BU21013_GAIN_1));
+ if (retval < 0) {
+ dev_err(&i2c->dev, "BU21013_GAIN reg write failed\n");
+ return retval;
+ }
+
+ retval = i2c_smbus_write_byte_data(i2c, BU21013_OFFSET_MODE_REG,
+ BU21013_OFFSET_MODE_DEFAULT);
+ if (retval < 0) {
+ dev_err(&i2c->dev, "BU21013_OFFSET_MODE reg write failed\n");
+ return retval;
+ }
+
+ retval = i2c_smbus_write_byte_data(i2c, BU21013_XY_EDGE_REG,
+ (BU21013_X_EDGE_0 | BU21013_X_EDGE_2 |
+ BU21013_Y_EDGE_1 | BU21013_Y_EDGE_3));
+ if (retval < 0) {
+ dev_err(&i2c->dev, "BU21013_XY_EDGE reg write failed\n");
+ return retval;
+ }
+
+ retval = i2c_smbus_write_byte_data(i2c, BU21013_DONE_REG,
+ BU21013_DONE);
+ if (retval < 0) {
+ dev_err(&i2c->dev, "BU21013_REG_DONE reg write failed\n");
+ return retval;
+ }
+
+ return 0;
+}
+
+/**
+ * bu21013_free_irq() - frees IRQ registered for touchscreen
+ * @bu21013_data: device structure pointer
+ *
+ * This function signals interrupt thread to stop processing and
+ * frees interrupt.
+ */
+static void bu21013_free_irq(struct bu21013_ts_data *bu21013_data)
+{
+ bu21013_data->touch_stopped = true;
+ wake_up(&bu21013_data->wait);
+ free_irq(bu21013_data->chip->irq, bu21013_data);
+}
+
+/**
+ * bu21013_probe() - initializes the i2c-client touchscreen driver
+ * @client: i2c client structure pointer
+ * @id: i2c device id pointer
+ *
+ * This function used to initializes the i2c-client touchscreen
+ * driver and returns integer.
+ */
+static int __devinit bu21013_probe(struct i2c_client *client,
+ const struct i2c_device_id *id)
+{
+ struct bu21013_ts_data *bu21013_data;
+ struct input_dev *in_dev;
+ const struct bu21013_platform_device *pdata =
+ client->dev.platform_data;
+ int error;
+
+ if (!i2c_check_functionality(client->adapter,
+ I2C_FUNC_SMBUS_BYTE_DATA)) {
+ dev_err(&client->dev, "i2c smbus byte data not supported\n");
+ return -EIO;
+ }
+
+ if (!pdata) {
+ dev_err(&client->dev, "platform data not defined\n");
+ return -EINVAL;
+ }
+
+ bu21013_data = kzalloc(sizeof(struct bu21013_ts_data), GFP_KERNEL);
+ in_dev = input_allocate_device();
+ if (!bu21013_data || !in_dev) {
+ dev_err(&client->dev, "device memory alloc failed\n");
+ error = -ENOMEM;
+ goto err_free_mem;
+ }
+
+ bu21013_data->in_dev = in_dev;
+ bu21013_data->chip = pdata;
+ bu21013_data->client = client;
+ bu21013_data->touch_stopped = false;
+ init_waitqueue_head(&bu21013_data->wait);
+
+ /* configure the gpio pins */
+ if (pdata->cs_en) {
+ error = pdata->cs_en(pdata->cs_pin);
+ if (error < 0) {
+ dev_err(&client->dev, "chip init failed\n");
+ goto err_free_mem;
+ }
+ }
+
+ /* configure the touch panel controller */
+ error = bu21013_init_chip(bu21013_data);
+ if (error) {
+ dev_err(&client->dev, "error in bu21013 config\n");
+ goto err_cs_disable;
+ }
+
+ /* register the device to input subsystem */
+ in_dev->name = DRIVER_TP;
+ in_dev->id.bustype = BUS_I2C;
+ in_dev->dev.parent = &client->dev;
+
+ __set_bit(EV_SYN, in_dev->evbit);
+ __set_bit(EV_KEY, in_dev->evbit);
+ __set_bit(EV_ABS, in_dev->evbit);
+
+ input_set_abs_params(in_dev, ABS_MT_POSITION_X, 0,
+ pdata->x_max_res, 0, 0);
+ input_set_abs_params(in_dev, ABS_MT_POSITION_Y, 0,
+ pdata->y_max_res, 0, 0);
+ input_set_drvdata(in_dev, bu21013_data);
+
+ error = request_threaded_irq(pdata->irq, NULL, bu21013_gpio_irq,
+ IRQF_TRIGGER_FALLING | IRQF_SHARED,
+ DRIVER_TP, bu21013_data);
+ if (error) {
+ dev_err(&client->dev, "request irq %d failed\n", pdata->irq);
+ goto err_cs_disable;
+ }
+
+ error = input_register_device(in_dev);
+ if (error) {
+ dev_err(&client->dev, "failed to register input device\n");
+ goto err_free_irq;
+ }
+
+ device_init_wakeup(&client->dev, pdata->wakeup);
+ i2c_set_clientdata(client, bu21013_data);
+
+ return 0;
+
+err_free_irq:
+ bu21013_free_irq(bu21013_data);
+err_cs_disable:
+ pdata->cs_dis(pdata->cs_pin);
+err_free_mem:
+ input_free_device(bu21013_data->in_dev);
+ kfree(bu21013_data);
+
+ return error;
+}
+/**
+ * bu21013_remove() - removes the i2c-client touchscreen driver
+ * @client: i2c client structure pointer
+ *
+ * This function uses to remove the i2c-client
+ * touchscreen driver and returns integer.
+ */
+static int __devexit bu21013_remove(struct i2c_client *client)
+{
+ struct bu21013_ts_data *bu21013_data = i2c_get_clientdata(client);
+
+ bu21013_free_irq(bu21013_data);
+
+ bu21013_data->chip->cs_dis(bu21013_data->chip->cs_pin);
+
+ input_unregister_device(bu21013_data->in_dev);
+ kfree(bu21013_data);
+
+ device_init_wakeup(&client->dev, false);
+
+ return 0;
+}
+
+#ifdef CONFIG_PM
+/**
+ * bu21013_suspend() - suspend the touch screen controller
+ * @dev: pointer to device structure
+ *
+ * This function is used to suspend the
+ * touch panel controller and returns integer
+ */
+static int bu21013_suspend(struct device *dev)
+{
+ struct bu21013_ts_data *bu21013_data = dev_get_drvdata(dev);
+ struct i2c_client *client = bu21013_data->client;
+
+ bu21013_data->touch_stopped = true;
+ if (device_may_wakeup(&client->dev))
+ enable_irq_wake(bu21013_data->chip->irq);
+ else
+ disable_irq(bu21013_data->chip->irq);
+
+ return 0;
+}
+
+/**
+ * bu21013_resume() - resume the touch screen controller
+ * @dev: pointer to device structure
+ *
+ * This function is used to resume the touch panel
+ * controller and returns integer.
+ */
+static int bu21013_resume(struct device *dev)
+{
+ struct bu21013_ts_data *bu21013_data = dev_get_drvdata(dev);
+ struct i2c_client *client = bu21013_data->client;
+ int retval;
+
+ retval = bu21013_init_chip(bu21013_data);
+ if (retval < 0) {
+ dev_err(&client->dev, "bu21013 controller config failed\n");
+ return retval;
+ }
+
+ bu21013_data->touch_stopped = false;
+
+ if (device_may_wakeup(&client->dev))
+ disable_irq_wake(bu21013_data->chip->irq);
+ else
+ enable_irq(bu21013_data->chip->irq);
+
+ return 0;
+}
+
+static const struct dev_pm_ops bu21013_dev_pm_ops = {
+ .suspend = bu21013_suspend,
+ .resume = bu21013_resume,
+};
+#endif
+
+static const struct i2c_device_id bu21013_id[] = {
+ { DRIVER_TP, 0 },
+ { }
+};
+MODULE_DEVICE_TABLE(i2c, bu21013_id);
+
+static struct i2c_driver bu21013_driver = {
+ .driver = {
+ .name = DRIVER_TP,
+ .owner = THIS_MODULE,
+#ifdef CONFIG_PM
+ .pm = &bu21013_dev_pm_ops,
+#endif
+ },
+ .probe = bu21013_probe,
+ .remove = __devexit_p(bu21013_remove),
+ .id_table = bu21013_id,
+};
+
+/**
+ * bu21013_init() - initializes the bu21013 touchscreen driver
+ *
+ * This function used to initializes the bu21013
+ * touchscreen driver and returns integer.
+ */
+static int __init bu21013_init(void)
+{
+ return i2c_add_driver(&bu21013_driver);
+}
+
+/**
+ * bu21013_exit() - de-initializes the bu21013 touchscreen driver
+ *
+ * This function uses to de-initializes the bu21013
+ * touchscreen driver and returns none.
+ */
+static void __exit bu21013_exit(void)
+{
+ i2c_del_driver(&bu21013_driver);
+}
+
+module_init(bu21013_init);
+module_exit(bu21013_exit);
+
+MODULE_LICENSE("GPL v2");
+MODULE_AUTHOR("Naveen Kumar G <naveen.gaddipati@stericsson.com>");
+MODULE_DESCRIPTION("bu21013 touch screen controller driver");
input_dev->keybit[BIT_WORD(BTN_TOUCH)] = BIT_MASK(BTN_TOUCH);
input_set_abs_params(input_dev, ABS_X,
- CY8CTMG110_X_MIN, CY8CTMG110_X_MAX, 0, 0);
+ CY8CTMG110_X_MIN, CY8CTMG110_X_MAX, 4, 0);
input_set_abs_params(input_dev, ABS_Y,
- CY8CTMG110_Y_MIN, CY8CTMG110_Y_MAX, 0, 0);
+ CY8CTMG110_Y_MIN, CY8CTMG110_Y_MAX, 4, 0);
if (ts->reset_pin) {
err = gpio_request(ts->reset_pin, NULL);
return 0;
fail2: free_irq(HP680_TS_IRQ, NULL);
- cancel_delayed_work(&work);
- flush_scheduled_work();
+ cancel_delayed_work_sync(&work);
fail1: input_free_device(hp680_ts_dev);
return err;
}
static void __exit hp680_ts_exit(void)
{
free_irq(HP680_TS_IRQ, NULL);
- cancel_delayed_work(&work);
- flush_scheduled_work();
+ cancel_delayed_work_sync(&work);
input_unregister_device(hp680_ts_dev);
}
--- /dev/null
+/*
+ * Intel MID Resistive Touch Screen Driver
+ *
+ * Copyright (C) 2008 Intel Corp
+ *
+ * ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; version 2 of the License.
+ *
+ * This program is distributed in the hope that it will be useful, but
+ * WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU
+ * General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License along
+ * with this program; if not, write to the Free Software Foundation, Inc.,
+ * 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA.
+ *
+ * Questions/Comments/Bug fixes to Sreedhara (sreedhara.ds@intel.com)
+ * Ramesh Agarwal (ramesh.agarwal@intel.com)
+ * ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
+ *
+ * TODO:
+ * review conversion of r/m/w sequences
+ */
+
+#include <linux/module.h>
+#include <linux/init.h>
+#include <linux/input.h>
+#include <linux/interrupt.h>
+#include <linux/err.h>
+#include <linux/param.h>
+#include <linux/slab.h>
+#include <linux/platform_device.h>
+#include <linux/irq.h>
+#include <linux/delay.h>
+#include <asm/intel_scu_ipc.h>
+
+/* PMIC Interrupt registers */
+#define PMIC_REG_ID1 0x00 /* PMIC ID1 register */
+
+/* PMIC Interrupt registers */
+#define PMIC_REG_INT 0x04 /* PMIC interrupt register */
+#define PMIC_REG_MINT 0x05 /* PMIC interrupt mask register */
+
+/* ADC Interrupt registers */
+#define PMIC_REG_ADCINT 0x5F /* ADC interrupt register */
+#define PMIC_REG_MADCINT 0x60 /* ADC interrupt mask register */
+
+/* ADC Control registers */
+#define PMIC_REG_ADCCNTL1 0x61 /* ADC control register */
+
+/* ADC Channel Selection registers */
+#define PMICADDR0 0xA4
+#define END_OF_CHANNEL 0x1F
+
+/* ADC Result register */
+#define PMIC_REG_ADCSNS0H 0x64
+
+/* ADC channels for touch screen */
+#define MRST_TS_CHAN10 0xA /* Touch screen X+ connection */
+#define MRST_TS_CHAN11 0xB /* Touch screen X- connection */
+#define MRST_TS_CHAN12 0xC /* Touch screen Y+ connection */
+#define MRST_TS_CHAN13 0xD /* Touch screen Y- connection */
+
+/* Touch screen channel BIAS constants */
+#define MRST_XBIAS 0x20
+#define MRST_YBIAS 0x40
+#define MRST_ZBIAS 0x80
+
+/* Touch screen coordinates */
+#define MRST_X_MIN 10
+#define MRST_X_MAX 1024
+#define MRST_X_FUZZ 5
+#define MRST_Y_MIN 10
+#define MRST_Y_MAX 1024
+#define MRST_Y_FUZZ 5
+#define MRST_PRESSURE_MIN 0
+#define MRST_PRESSURE_NOMINAL 50
+#define MRST_PRESSURE_MAX 100
+
+#define WAIT_ADC_COMPLETION 10 /* msec */
+
+/* PMIC ADC round robin delays */
+#define ADC_LOOP_DELAY0 0x0 /* Continuous loop */
+#define ADC_LOOP_DELAY1 0x1 /* 4.5 ms approximate */
+
+/* PMIC Vendor Identifiers */
+#define PMIC_VENDOR_FS 0 /* PMIC vendor FreeScale */
+#define PMIC_VENDOR_MAXIM 1 /* PMIC vendor MAXIM */
+#define PMIC_VENDOR_NEC 2 /* PMIC vendor NEC */
+#define MRSTOUCH_MAX_CHANNELS 32 /* Maximum ADC channels */
+
+/* Touch screen device structure */
+struct mrstouch_dev {
+ struct device *dev; /* device associated with touch screen */
+ struct input_dev *input;
+ char phys[32];
+ u16 asr; /* Address selection register */
+ int irq;
+ unsigned int vendor; /* PMIC vendor */
+ unsigned int rev; /* PMIC revision */
+
+ int (*read_prepare)(struct mrstouch_dev *tsdev);
+ int (*read)(struct mrstouch_dev *tsdev, u16 *x, u16 *y, u16 *z);
+ int (*read_finish)(struct mrstouch_dev *tsdev);
+};
+
+
+/*************************** NEC and Maxim Interface ************************/
+
+static int mrstouch_nec_adc_read_prepare(struct mrstouch_dev *tsdev)
+{
+ return intel_scu_ipc_update_register(PMIC_REG_MADCINT, 0, 0x20);
+}
+
+/*
+ * Enables PENDET interrupt.
+ */
+static int mrstouch_nec_adc_read_finish(struct mrstouch_dev *tsdev)
+{
+ int err;
+
+ err = intel_scu_ipc_update_register(PMIC_REG_MADCINT, 0x20, 0x20);
+ if (!err)
+ err = intel_scu_ipc_update_register(PMIC_REG_ADCCNTL1, 0, 0x05);
+
+ return err;
+}
+
+/*
+ * Reads PMIC ADC touch screen result
+ * Reads ADC storage registers for higher 7 and lower 3 bits and
+ * converts the two readings into a single value and turns off gain bit
+ */
+static int mrstouch_ts_chan_read(u16 offset, u16 chan, u16 *vp, u16 *vm)
+{
+ int err;
+ u16 result;
+ u32 res;
+
+ result = PMIC_REG_ADCSNS0H + offset;
+
+ if (chan == MRST_TS_CHAN12)
+ result += 4;
+
+ err = intel_scu_ipc_ioread32(result, &res);
+ if (err)
+ return err;
+
+ /* Mash the bits up */
+
+ *vp = (res & 0xFF) << 3; /* Highest 7 bits */
+ *vp |= (res >> 8) & 0x07; /* Lower 3 bits */
+ *vp &= 0x3FF;
+
+ res >>= 16;
+
+ *vm = (res & 0xFF) << 3; /* Highest 7 bits */
+ *vm |= (res >> 8) & 0x07; /* Lower 3 bits */
+ *vm &= 0x3FF;
+
+ return 0;
+}
+
+/*
+ * Enables X, Y and Z bias values
+ * Enables YPYM for X channels and XPXM for Y channels
+ */
+static int mrstouch_ts_bias_set(uint offset, uint bias)
+{
+ int count;
+ u16 chan, start;
+ u16 reg[4];
+ u8 data[4];
+
+ chan = PMICADDR0 + offset;
+ start = MRST_TS_CHAN10;
+
+ for (count = 0; count <= 3; count++) {
+ reg[count] = chan++;
+ data[count] = bias | (start + count);
+ }
+
+ return intel_scu_ipc_writev(reg, data, 4);
+}
+
+/* To read touch screen channel values */
+static int mrstouch_nec_adc_read(struct mrstouch_dev *tsdev,
+ u16 *x, u16 *y, u16 *z)
+{
+ int err;
+ u16 xm, ym, zm;
+
+ /* configure Y bias for X channels */
+ err = mrstouch_ts_bias_set(tsdev->asr, MRST_YBIAS);
+ if (err)
+ goto ipc_error;
+
+ msleep(WAIT_ADC_COMPLETION);
+
+ /* read x+ and x- channels */
+ err = mrstouch_ts_chan_read(tsdev->asr, MRST_TS_CHAN10, x, &xm);
+ if (err)
+ goto ipc_error;
+
+ /* configure x bias for y channels */
+ err = mrstouch_ts_bias_set(tsdev->asr, MRST_XBIAS);
+ if (err)
+ goto ipc_error;
+
+ msleep(WAIT_ADC_COMPLETION);
+
+ /* read y+ and y- channels */
+ err = mrstouch_ts_chan_read(tsdev->asr, MRST_TS_CHAN12, y, &ym);
+ if (err)
+ goto ipc_error;
+
+ /* configure z bias for x and y channels */
+ err = mrstouch_ts_bias_set(tsdev->asr, MRST_ZBIAS);
+ if (err)
+ goto ipc_error;
+
+ msleep(WAIT_ADC_COMPLETION);
+
+ /* read z+ and z- channels */
+ err = mrstouch_ts_chan_read(tsdev->asr, MRST_TS_CHAN10, z, &zm);
+ if (err)
+ goto ipc_error;
+
+ return 0;
+
+ipc_error:
+ dev_err(tsdev->dev, "ipc error during adc read\n");
+ return err;
+}
+
+
+/*************************** Freescale Interface ************************/
+
+static int mrstouch_fs_adc_read_prepare(struct mrstouch_dev *tsdev)
+{
+ int err, count;
+ u16 chan;
+ u16 reg[5];
+ u8 data[5];
+
+ /* Stop the ADC */
+ err = intel_scu_ipc_update_register(PMIC_REG_MADCINT, 0x00, 0x02);
+ if (err)
+ goto ipc_error;
+
+ chan = PMICADDR0 + tsdev->asr;
+
+ /* Set X BIAS */
+ for (count = 0; count <= 3; count++) {
+ reg[count] = chan++;
+ data[count] = 0x2A;
+ }
+ reg[count] = chan++; /* Dummy */
+ data[count] = 0;
+
+ err = intel_scu_ipc_writev(reg, data, 5);
+ if (err)
+ goto ipc_error;
+
+ msleep(WAIT_ADC_COMPLETION);
+
+ /* Set Y BIAS */
+ for (count = 0; count <= 3; count++) {
+ reg[count] = chan++;
+ data[count] = 0x4A;
+ }
+ reg[count] = chan++; /* Dummy */
+ data[count] = 0;
+
+ err = intel_scu_ipc_writev(reg, data, 5);
+ if (err)
+ goto ipc_error;
+
+ msleep(WAIT_ADC_COMPLETION);
+
+ /* Set Z BIAS */
+ err = intel_scu_ipc_iowrite32(chan + 2, 0x8A8A8A8A);
+ if (err)
+ goto ipc_error;
+
+ msleep(WAIT_ADC_COMPLETION);
+
+ return 0;
+
+ipc_error:
+ dev_err(tsdev->dev, "ipc error during %s\n", __func__);
+ return err;
+}
+
+static int mrstouch_fs_adc_read(struct mrstouch_dev *tsdev,
+ u16 *x, u16 *y, u16 *z)
+{
+ int err;
+ u16 result;
+ u16 reg[4];
+ u8 data[4];
+
+ result = PMIC_REG_ADCSNS0H + tsdev->asr;
+
+ reg[0] = result + 4;
+ reg[1] = result + 5;
+ reg[2] = result + 16;
+ reg[3] = result + 17;
+
+ err = intel_scu_ipc_readv(reg, data, 4);
+ if (err)
+ goto ipc_error;
+
+ *x = data[0] << 3; /* Higher 7 bits */
+ *x |= data[1] & 0x7; /* Lower 3 bits */
+ *x &= 0x3FF;
+
+ *y = data[2] << 3; /* Higher 7 bits */
+ *y |= data[3] & 0x7; /* Lower 3 bits */
+ *y &= 0x3FF;
+
+ /* Read Z value */
+ reg[0] = result + 28;
+ reg[1] = result + 29;
+
+ err = intel_scu_ipc_readv(reg, data, 4);
+ if (err)
+ goto ipc_error;
+
+ *z = data[0] << 3; /* Higher 7 bits */
+ *z |= data[1] & 0x7; /* Lower 3 bits */
+ *z &= 0x3FF;
+
+ return 0;
+
+ipc_error:
+ dev_err(tsdev->dev, "ipc error during %s\n", __func__);
+ return err;
+}
+
+static int mrstouch_fs_adc_read_finish(struct mrstouch_dev *tsdev)
+{
+ int err, count;
+ u16 chan;
+ u16 reg[5];
+ u8 data[5];
+
+ /* Clear all TS channels */
+ chan = PMICADDR0 + tsdev->asr;
+ for (count = 0; count <= 4; count++) {
+ reg[count] = chan++;
+ data[count] = 0;
+ }
+ err = intel_scu_ipc_writev(reg, data, 5);
+ if (err)
+ goto ipc_error;
+
+ for (count = 0; count <= 4; count++) {
+ reg[count] = chan++;
+ data[count] = 0;
+ }
+ err = intel_scu_ipc_writev(reg, data, 5);
+ if (err)
+ goto ipc_error;
+
+ err = intel_scu_ipc_iowrite32(chan + 2, 0x00000000);
+ if (err)
+ goto ipc_error;
+
+ /* Start ADC */
+ err = intel_scu_ipc_update_register(PMIC_REG_MADCINT, 0x02, 0x02);
+ if (err)
+ goto ipc_error;
+
+ return 0;
+
+ipc_error:
+ dev_err(tsdev->dev, "ipc error during %s\n", __func__);
+ return err;
+}
+
+static void mrstouch_report_event(struct input_dev *input,
+ unsigned int x, unsigned int y, unsigned int z)
+{
+ if (z > MRST_PRESSURE_NOMINAL) {
+ /* Pen touched, report button touch and coordinates */
+ input_report_key(input, BTN_TOUCH, 1);
+ input_report_abs(input, ABS_X, x);
+ input_report_abs(input, ABS_Y, y);
+ } else {
+ input_report_key(input, BTN_TOUCH, 0);
+ }
+
+ input_report_abs(input, ABS_PRESSURE, z);
+ input_sync(input);
+}
+
+/* PENDET interrupt handler */
+static irqreturn_t mrstouch_pendet_irq(int irq, void *dev_id)
+{
+ struct mrstouch_dev *tsdev = dev_id;
+ u16 x, y, z;
+
+ /*
+ * Should we lower thread priority? Probably not, since we are
+ * not spinning but sleeping...
+ */
+
+ if (tsdev->read_prepare(tsdev))
+ goto out;
+
+ do {
+ if (tsdev->read(tsdev, &x, &y, &z))
+ break;
+
+ mrstouch_report_event(tsdev->input, x, y, z);
+ } while (z > MRST_PRESSURE_NOMINAL);
+
+ tsdev->read_finish(tsdev);
+
+out:
+ return IRQ_HANDLED;
+}
+
+/* Utility to read PMIC ID */
+static int __devinit mrstouch_read_pmic_id(uint *vendor, uint *rev)
+{
+ int err;
+ u8 r;
+
+ err = intel_scu_ipc_ioread8(PMIC_REG_ID1, &r);
+ if (err)
+ return err;
+
+ *vendor = r & 0x7;
+ *rev = (r >> 3) & 0x7;
+
+ return 0;
+}
+
+/*
+ * Parse ADC channels to find end of the channel configured by other ADC user
+ * NEC and MAXIM requires 4 channels and FreeScale needs 18 channels
+ */
+static int __devinit mrstouch_chan_parse(struct mrstouch_dev *tsdev)
+{
+ int err, i, found;
+ u8 r8;
+
+ found = -1;
+
+ for (i = 0; i < MRSTOUCH_MAX_CHANNELS; i++) {
+ if (found >= 0)
+ break;
+
+ err = intel_scu_ipc_ioread8(PMICADDR0 + i, &r8);
+ if (err)
+ return err;
+
+ if (r8 == END_OF_CHANNEL) {
+ found = i;
+ break;
+ }
+ }
+ if (found < 0)
+ return 0;
+
+ if (tsdev->vendor == PMIC_VENDOR_FS) {
+ if (found && found > (MRSTOUCH_MAX_CHANNELS - 18))
+ return -ENOSPC;
+ } else {
+ if (found && found > (MRSTOUCH_MAX_CHANNELS - 4))
+ return -ENOSPC;
+ }
+ return found;
+}
+
+
+/*
+ * Writes touch screen channels to ADC address selection registers
+ */
+static int __devinit mrstouch_ts_chan_set(uint offset)
+{
+ u16 chan;
+
+ int ret, count;
+
+ chan = PMICADDR0 + offset;
+ for (count = 0; count <= 3; count++) {
+ ret = intel_scu_ipc_iowrite8(chan++, MRST_TS_CHAN10 + count);
+ if (ret)
+ return ret;
+ }
+ return intel_scu_ipc_iowrite8(chan++, END_OF_CHANNEL);
+}
+
+/* Initialize ADC */
+static int __devinit mrstouch_adc_init(struct mrstouch_dev *tsdev)
+{
+ int err, start;
+ u8 ra, rm;
+
+ err = mrstouch_read_pmic_id(&tsdev->vendor, &tsdev->rev);
+ if (err) {
+ dev_err(tsdev->dev, "Unable to read PMIC id\n");
+ return err;
+ }
+
+ switch (tsdev->vendor) {
+ case PMIC_VENDOR_NEC:
+ case PMIC_VENDOR_MAXIM:
+ tsdev->read_prepare = mrstouch_nec_adc_read_prepare;
+ tsdev->read = mrstouch_nec_adc_read;
+ tsdev->read_finish = mrstouch_nec_adc_read_finish;
+ break;
+
+ case PMIC_VENDOR_FS:
+ tsdev->read_prepare = mrstouch_fs_adc_read_prepare;
+ tsdev->read = mrstouch_fs_adc_read;
+ tsdev->read_finish = mrstouch_fs_adc_read_finish;
+ break;
+
+ default:
+ dev_err(tsdev->dev,
+ "Unsupported touchscreen: %d\n", tsdev->vendor);
+ return -ENXIO;
+ }
+
+ start = mrstouch_chan_parse(tsdev);
+ if (start < 0) {
+ dev_err(tsdev->dev, "Unable to parse channels\n");
+ return start;
+ }
+
+ tsdev->asr = start;
+
+ /*
+ * ADC power on, start, enable PENDET and set loop delay
+ * ADC loop delay is set to 4.5 ms approximately
+ * Loop delay more than this results in jitter in adc readings
+ * Setting loop delay to 0 (continous loop) in MAXIM stops PENDET
+ * interrupt generation sometimes.
+ */
+
+ if (tsdev->vendor == PMIC_VENDOR_FS) {
+ ra = 0xE0 | ADC_LOOP_DELAY0;
+ rm = 0x5;
+ } else {
+ /* NEC and MAXIm not consistent with loop delay 0 */
+ ra = 0xE0 | ADC_LOOP_DELAY1;
+ rm = 0x0;
+
+ /* configure touch screen channels */
+ err = mrstouch_ts_chan_set(tsdev->asr);
+ if (err)
+ return err;
+ }
+
+ err = intel_scu_ipc_update_register(PMIC_REG_ADCCNTL1, ra, 0xE7);
+ if (err)
+ return err;
+
+ err = intel_scu_ipc_update_register(PMIC_REG_MADCINT, rm, 0x03);
+ if (err)
+ return err;
+
+ return 0;
+}
+
+
+/* Probe function for touch screen driver */
+static int __devinit mrstouch_probe(struct platform_device *pdev)
+{
+ struct mrstouch_dev *tsdev;
+ struct input_dev *input;
+ int err;
+ int irq;
+
+ irq = platform_get_irq(pdev, 0);
+ if (irq < 0) {
+ dev_err(&pdev->dev, "no interrupt assigned\n");
+ return -EINVAL;
+ }
+
+ tsdev = kzalloc(sizeof(struct mrstouch_dev), GFP_KERNEL);
+ input = input_allocate_device();
+ if (!tsdev || !input) {
+ dev_err(&pdev->dev, "unable to allocate memory\n");
+ err = -ENOMEM;
+ goto err_free_mem;
+ }
+
+ tsdev->dev = &pdev->dev;
+ tsdev->input = input;
+ tsdev->irq = irq;
+
+ snprintf(tsdev->phys, sizeof(tsdev->phys),
+ "%s/input0", dev_name(tsdev->dev));
+
+ err = mrstouch_adc_init(tsdev);
+ if (err) {
+ dev_err(&pdev->dev, "ADC initialization failed\n");
+ goto err_free_mem;
+ }
+
+ input->name = "mrst_touchscreen";
+ input->phys = tsdev->phys;
+ input->dev.parent = tsdev->dev;
+
+ input->id.vendor = tsdev->vendor;
+ input->id.version = tsdev->rev;
+
+ input->evbit[0] = BIT_MASK(EV_KEY) | BIT_MASK(EV_ABS);
+ input->keybit[BIT_WORD(BTN_TOUCH)] = BIT_MASK(BTN_TOUCH);
+
+ input_set_abs_params(tsdev->input, ABS_X,
+ MRST_X_MIN, MRST_X_MAX, MRST_X_FUZZ, 0);
+ input_set_abs_params(tsdev->input, ABS_Y,
+ MRST_Y_MIN, MRST_Y_MAX, MRST_Y_FUZZ, 0);
+ input_set_abs_params(tsdev->input, ABS_PRESSURE,
+ MRST_PRESSURE_MIN, MRST_PRESSURE_MAX, 0, 0);
+
+ err = request_threaded_irq(tsdev->irq, NULL, mrstouch_pendet_irq,
+ 0, "mrstouch", tsdev);
+ if (err) {
+ dev_err(tsdev->dev, "unable to allocate irq\n");
+ goto err_free_mem;
+ }
+
+ err = input_register_device(tsdev->input);
+ if (err) {
+ dev_err(tsdev->dev, "unable to register input device\n");
+ goto err_free_irq;
+ }
+
+ platform_set_drvdata(pdev, tsdev);
+ return 0;
+
+err_free_irq:
+ free_irq(tsdev->irq, tsdev);
+err_free_mem:
+ input_free_device(input);
+ kfree(tsdev);
+ return err;
+}
+
+static int __devexit mrstouch_remove(struct platform_device *pdev)
+{
+ struct mrstouch_dev *tsdev = platform_get_drvdata(pdev);
+
+ free_irq(tsdev->irq, tsdev);
+ input_unregister_device(tsdev->input);
+ kfree(tsdev);
+
+ platform_set_drvdata(pdev, NULL);
+
+ return 0;
+}
+
+static struct platform_driver mrstouch_driver = {
+ .driver = {
+ .name = "pmic_touch",
+ .owner = THIS_MODULE,
+ },
+ .probe = mrstouch_probe,
+ .remove = __devexit_p(mrstouch_remove),
+};
+
+static int __init mrstouch_init(void)
+{
+ return platform_driver_register(&mrstouch_driver);
+}
+module_init(mrstouch_init);
+
+static void __exit mrstouch_exit(void)
+{
+ platform_driver_unregister(&mrstouch_driver);
+}
+module_exit(mrstouch_exit);
+
+MODULE_AUTHOR("Sreedhara Murthy. D.S, sreedhara.ds@intel.com");
+MODULE_DESCRIPTION("Intel Moorestown Resistive Touch Screen Driver");
+MODULE_LICENSE("GPL");
--- /dev/null
+/*
+ * LPC32xx built-in touchscreen driver
+ *
+ * Copyright (C) 2010 NXP Semiconductors
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ */
+
+#include <linux/platform_device.h>
+#include <linux/init.h>
+#include <linux/input.h>
+#include <linux/interrupt.h>
+#include <linux/module.h>
+#include <linux/clk.h>
+#include <linux/io.h>
+#include <linux/slab.h>
+
+/*
+ * Touchscreen controller register offsets
+ */
+#define LPC32XX_TSC_STAT 0x00
+#define LPC32XX_TSC_SEL 0x04
+#define LPC32XX_TSC_CON 0x08
+#define LPC32XX_TSC_FIFO 0x0C
+#define LPC32XX_TSC_DTR 0x10
+#define LPC32XX_TSC_RTR 0x14
+#define LPC32XX_TSC_UTR 0x18
+#define LPC32XX_TSC_TTR 0x1C
+#define LPC32XX_TSC_DXP 0x20
+#define LPC32XX_TSC_MIN_X 0x24
+#define LPC32XX_TSC_MAX_X 0x28
+#define LPC32XX_TSC_MIN_Y 0x2C
+#define LPC32XX_TSC_MAX_Y 0x30
+#define LPC32XX_TSC_AUX_UTR 0x34
+#define LPC32XX_TSC_AUX_MIN 0x38
+#define LPC32XX_TSC_AUX_MAX 0x3C
+
+#define LPC32XX_TSC_STAT_FIFO_OVRRN (1 << 8)
+#define LPC32XX_TSC_STAT_FIFO_EMPTY (1 << 7)
+
+#define LPC32XX_TSC_SEL_DEFVAL 0x0284
+
+#define LPC32XX_TSC_ADCCON_IRQ_TO_FIFO_4 (0x1 << 11)
+#define LPC32XX_TSC_ADCCON_X_SAMPLE_SIZE(s) ((10 - (s)) << 7)
+#define LPC32XX_TSC_ADCCON_Y_SAMPLE_SIZE(s) ((10 - (s)) << 4)
+#define LPC32XX_TSC_ADCCON_POWER_UP (1 << 2)
+#define LPC32XX_TSC_ADCCON_AUTO_EN (1 << 0)
+
+#define LPC32XX_TSC_FIFO_TS_P_LEVEL (1 << 31)
+#define LPC32XX_TSC_FIFO_NORMALIZE_X_VAL(x) (((x) & 0x03FF0000) >> 16)
+#define LPC32XX_TSC_FIFO_NORMALIZE_Y_VAL(y) ((y) & 0x000003FF)
+
+#define LPC32XX_TSC_ADCDAT_VALUE_MASK 0x000003FF
+
+#define LPC32XX_TSC_MIN_XY_VAL 0x0
+#define LPC32XX_TSC_MAX_XY_VAL 0x3FF
+
+#define MOD_NAME "ts-lpc32xx"
+
+#define tsc_readl(dev, reg) \
+ __raw_readl((dev)->tsc_base + (reg))
+#define tsc_writel(dev, reg, val) \
+ __raw_writel((val), (dev)->tsc_base + (reg))
+
+struct lpc32xx_tsc {
+ struct input_dev *dev;
+ void __iomem *tsc_base;
+ int irq;
+ struct clk *clk;
+};
+
+static void lpc32xx_fifo_clear(struct lpc32xx_tsc *tsc)
+{
+ while (!(tsc_readl(tsc, LPC32XX_TSC_STAT) &
+ LPC32XX_TSC_STAT_FIFO_EMPTY))
+ tsc_readl(tsc, LPC32XX_TSC_FIFO);
+}
+
+static irqreturn_t lpc32xx_ts_interrupt(int irq, void *dev_id)
+{
+ u32 tmp, rv[4], xs[4], ys[4];
+ int idx;
+ struct lpc32xx_tsc *tsc = dev_id;
+ struct input_dev *input = tsc->dev;
+
+ tmp = tsc_readl(tsc, LPC32XX_TSC_STAT);
+
+ if (tmp & LPC32XX_TSC_STAT_FIFO_OVRRN) {
+ /* FIFO overflow - throw away samples */
+ lpc32xx_fifo_clear(tsc);
+ return IRQ_HANDLED;
+ }
+
+ /*
+ * Gather and normalize 4 samples. Pen-up events may have less
+ * than 4 samples, but its ok to pop 4 and let the last sample
+ * pen status check drop the samples.
+ */
+ idx = 0;
+ while (idx < 4 &&
+ !(tsc_readl(tsc, LPC32XX_TSC_STAT) &
+ LPC32XX_TSC_STAT_FIFO_EMPTY)) {
+ tmp = tsc_readl(tsc, LPC32XX_TSC_FIFO);
+ xs[idx] = LPC32XX_TSC_ADCDAT_VALUE_MASK -
+ LPC32XX_TSC_FIFO_NORMALIZE_X_VAL(tmp);
+ ys[idx] = LPC32XX_TSC_ADCDAT_VALUE_MASK -
+ LPC32XX_TSC_FIFO_NORMALIZE_Y_VAL(tmp);
+ rv[idx] = tmp;
+ idx++;
+ }
+
+ /* Data is only valid if pen is still down in last sample */
+ if (!(rv[3] & LPC32XX_TSC_FIFO_TS_P_LEVEL) && idx == 4) {
+ /* Use average of 2nd and 3rd sample for position */
+ input_report_abs(input, ABS_X, (xs[1] + xs[2]) / 2);
+ input_report_abs(input, ABS_Y, (ys[1] + ys[2]) / 2);
+ input_report_key(input, BTN_TOUCH, 1);
+ } else {
+ input_report_key(input, BTN_TOUCH, 0);
+ }
+
+ input_sync(input);
+
+ return IRQ_HANDLED;
+}
+
+static void lpc32xx_stop_tsc(struct lpc32xx_tsc *tsc)
+{
+ /* Disable auto mode */
+ tsc_writel(tsc, LPC32XX_TSC_CON,
+ tsc_readl(tsc, LPC32XX_TSC_CON) &
+ ~LPC32XX_TSC_ADCCON_AUTO_EN);
+
+ clk_disable(tsc->clk);
+}
+
+static void lpc32xx_setup_tsc(struct lpc32xx_tsc *tsc)
+{
+ u32 tmp;
+
+ clk_enable(tsc->clk);
+
+ tmp = tsc_readl(tsc, LPC32XX_TSC_CON) & ~LPC32XX_TSC_ADCCON_POWER_UP;
+
+ /* Set the TSC FIFO depth to 4 samples @ 10-bits per sample (max) */
+ tmp = LPC32XX_TSC_ADCCON_IRQ_TO_FIFO_4 |
+ LPC32XX_TSC_ADCCON_X_SAMPLE_SIZE(10) |
+ LPC32XX_TSC_ADCCON_Y_SAMPLE_SIZE(10);
+ tsc_writel(tsc, LPC32XX_TSC_CON, tmp);
+
+ /* These values are all preset */
+ tsc_writel(tsc, LPC32XX_TSC_SEL, LPC32XX_TSC_SEL_DEFVAL);
+ tsc_writel(tsc, LPC32XX_TSC_MIN_X, LPC32XX_TSC_MIN_XY_VAL);
+ tsc_writel(tsc, LPC32XX_TSC_MAX_X, LPC32XX_TSC_MAX_XY_VAL);
+ tsc_writel(tsc, LPC32XX_TSC_MIN_Y, LPC32XX_TSC_MIN_XY_VAL);
+ tsc_writel(tsc, LPC32XX_TSC_MAX_Y, LPC32XX_TSC_MAX_XY_VAL);
+
+ /* Aux support is not used */
+ tsc_writel(tsc, LPC32XX_TSC_AUX_UTR, 0);
+ tsc_writel(tsc, LPC32XX_TSC_AUX_MIN, 0);
+ tsc_writel(tsc, LPC32XX_TSC_AUX_MAX, 0);
+
+ /*
+ * Set sample rate to about 240Hz per X/Y pair. A single measurement
+ * consists of 4 pairs which gives about a 60Hz sample rate based on
+ * a stable 32768Hz clock source. Values are in clocks.
+ * Rate is (32768 / (RTR + XCONV + RTR + YCONV + DXP + TTR + UTR) / 4
+ */
+ tsc_writel(tsc, LPC32XX_TSC_RTR, 0x2);
+ tsc_writel(tsc, LPC32XX_TSC_DTR, 0x2);
+ tsc_writel(tsc, LPC32XX_TSC_TTR, 0x10);
+ tsc_writel(tsc, LPC32XX_TSC_DXP, 0x4);
+ tsc_writel(tsc, LPC32XX_TSC_UTR, 88);
+
+ lpc32xx_fifo_clear(tsc);
+
+ /* Enable automatic ts event capture */
+ tsc_writel(tsc, LPC32XX_TSC_CON, tmp | LPC32XX_TSC_ADCCON_AUTO_EN);
+}
+
+static int lpc32xx_ts_open(struct input_dev *dev)
+{
+ struct lpc32xx_tsc *tsc = input_get_drvdata(dev);
+
+ lpc32xx_setup_tsc(tsc);
+
+ return 0;
+}
+
+static void lpc32xx_ts_close(struct input_dev *dev)
+{
+ struct lpc32xx_tsc *tsc = input_get_drvdata(dev);
+
+ lpc32xx_stop_tsc(tsc);
+}
+
+static int __devinit lpc32xx_ts_probe(struct platform_device *pdev)
+{
+ struct lpc32xx_tsc *tsc;
+ struct input_dev *input;
+ struct resource *res;
+ resource_size_t size;
+ int irq;
+ int error;
+
+ res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+ if (!res) {
+ dev_err(&pdev->dev, "Can't get memory resource\n");
+ return -ENOENT;
+ }
+
+ irq = platform_get_irq(pdev, 0);
+ if (irq < 0) {
+ dev_err(&pdev->dev, "Can't get interrupt resource\n");
+ return irq;
+ }
+
+ tsc = kzalloc(sizeof(*tsc), GFP_KERNEL);
+ input = input_allocate_device();
+ if (!tsc || !input) {
+ dev_err(&pdev->dev, "failed allocating memory\n");
+ error = -ENOMEM;
+ goto err_free_mem;
+ }
+
+ tsc->dev = input;
+ tsc->irq = irq;
+
+ size = resource_size(res);
+
+ if (!request_mem_region(res->start, size, pdev->name)) {
+ dev_err(&pdev->dev, "TSC registers are not free\n");
+ error = -EBUSY;
+ goto err_free_mem;
+ }
+
+ tsc->tsc_base = ioremap(res->start, size);
+ if (!tsc->tsc_base) {
+ dev_err(&pdev->dev, "Can't map memory\n");
+ error = -ENOMEM;
+ goto err_release_mem;
+ }
+
+ tsc->clk = clk_get(&pdev->dev, NULL);
+ if (IS_ERR(tsc->clk)) {
+ dev_err(&pdev->dev, "failed getting clock\n");
+ error = PTR_ERR(tsc->clk);
+ goto err_unmap;
+ }
+
+ input->name = MOD_NAME;
+ input->phys = "lpc32xx/input0";
+ input->id.bustype = BUS_HOST;
+ input->id.vendor = 0x0001;
+ input->id.product = 0x0002;
+ input->id.version = 0x0100;
+ input->dev.parent = &pdev->dev;
+ input->open = lpc32xx_ts_open;
+ input->close = lpc32xx_ts_close;
+
+ input->evbit[0] = BIT_MASK(EV_KEY) | BIT_MASK(EV_ABS);
+ input->keybit[BIT_WORD(BTN_TOUCH)] = BIT_MASK(BTN_TOUCH);
+ input_set_abs_params(input, ABS_X, LPC32XX_TSC_MIN_XY_VAL,
+ LPC32XX_TSC_MAX_XY_VAL, 0, 0);
+ input_set_abs_params(input, ABS_Y, LPC32XX_TSC_MIN_XY_VAL,
+ LPC32XX_TSC_MAX_XY_VAL, 0, 0);
+
+ input_set_drvdata(input, tsc);
+
+ error = request_irq(tsc->irq, lpc32xx_ts_interrupt,
+ IRQF_DISABLED, pdev->name, tsc);
+ if (error) {
+ dev_err(&pdev->dev, "failed requesting interrupt\n");
+ goto err_put_clock;
+ }
+
+ error = input_register_device(input);
+ if (error) {
+ dev_err(&pdev->dev, "failed registering input device\n");
+ goto err_free_irq;
+ }
+
+ platform_set_drvdata(pdev, tsc);
+ device_init_wakeup(&pdev->dev, 1);
+
+ return 0;
+
+err_free_irq:
+ free_irq(tsc->irq, tsc);
+err_put_clock:
+ clk_put(tsc->clk);
+err_unmap:
+ iounmap(tsc->tsc_base);
+err_release_mem:
+ release_mem_region(res->start, size);
+err_free_mem:
+ input_free_device(input);
+ kfree(tsc);
+
+ return error;
+}
+
+static int __devexit lpc32xx_ts_remove(struct platform_device *pdev)
+{
+ struct lpc32xx_tsc *tsc = platform_get_drvdata(pdev);
+ struct resource *res;
+
+ device_init_wakeup(&pdev->dev, 0);
+ free_irq(tsc->irq, tsc);
+
+ input_unregister_device(tsc->dev);
+
+ clk_put(tsc->clk);
+
+ iounmap(tsc->tsc_base);
+ res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+ release_mem_region(res->start, resource_size(res));
+
+ kfree(tsc);
+
+ return 0;
+}
+
+#ifdef CONFIG_PM
+static int lpc32xx_ts_suspend(struct device *dev)
+{
+ struct lpc32xx_tsc *tsc = dev_get_drvdata(dev);
+ struct input_dev *input = tsc->dev;
+
+ /*
+ * Suspend and resume can be called when the device hasn't been
+ * enabled. If there are no users that have the device open, then
+ * avoid calling the TSC stop and start functions as the TSC
+ * isn't yet clocked.
+ */
+ mutex_lock(&input->mutex);
+
+ if (input->users) {
+ if (device_may_wakeup(dev))
+ enable_irq_wake(tsc->irq);
+ else
+ lpc32xx_stop_tsc(tsc);
+ }
+
+ mutex_unlock(&input->mutex);
+
+ return 0;
+}
+
+static int lpc32xx_ts_resume(struct device *dev)
+{
+ struct lpc32xx_tsc *tsc = dev_get_drvdata(dev);
+ struct input_dev *input = tsc->dev;
+
+ mutex_lock(&input->mutex);
+
+ if (input->users) {
+ if (device_may_wakeup(dev))
+ disable_irq_wake(tsc->irq);
+ else
+ lpc32xx_setup_tsc(tsc);
+ }
+
+ mutex_unlock(&input->mutex);
+
+ return 0;
+}
+
+static const struct dev_pm_ops lpc32xx_ts_pm_ops = {
+ .suspend = lpc32xx_ts_suspend,
+ .resume = lpc32xx_ts_resume,
+};
+#define LPC32XX_TS_PM_OPS (&lpc32xx_ts_pm_ops)
+#else
+#define LPC32XX_TS_PM_OPS NULL
+#endif
+
+static struct platform_driver lpc32xx_ts_driver = {
+ .probe = lpc32xx_ts_probe,
+ .remove = __devexit_p(lpc32xx_ts_remove),
+ .driver = {
+ .name = MOD_NAME,
+ .owner = THIS_MODULE,
+ .pm = LPC32XX_TS_PM_OPS,
+ },
+};
+
+static int __init lpc32xx_ts_init(void)
+{
+ return platform_driver_register(&lpc32xx_ts_driver);
+}
+module_init(lpc32xx_ts_init);
+
+static void __exit lpc32xx_ts_exit(void)
+{
+ platform_driver_unregister(&lpc32xx_ts_driver);
+}
+module_exit(lpc32xx_ts_exit);
+
+MODULE_AUTHOR("Kevin Wells <kevin.wells@nxp.com");
+MODULE_DESCRIPTION("LPC32XX TSC Driver");
+MODULE_LICENSE("GPL");
+MODULE_ALIAS("platform:lpc32xx_ts");
err_tcirq:
free_irq(ts.irq_tc, ts.input);
err_inputdev:
- input_unregister_device(ts.input);
+ input_free_device(ts.input);
err_iomap:
iounmap(ts.io);
err_clk:
struct stmpe_touch *ts;
struct input_dev *idev;
struct stmpe_ts_platform_data *ts_pdata = NULL;
- int ret = 0;
+ int ret;
int ts_irq;
ts_irq = platform_get_irq_byname(pdev, "FIFO_TH");
return ts_irq;
ts = kzalloc(sizeof(*ts), GFP_KERNEL);
- if (!ts)
+ if (!ts) {
+ ret = -ENOMEM;
goto err_out;
+ }
idev = input_allocate_device();
- if (!idev)
+ if (!idev) {
+ ret = -ENOMEM;
goto err_free_ts;
+ }
platform_set_drvdata(pdev, ts);
ts->stmpe = stmpe;
platform_set_drvdata(pdev, NULL);
input_unregister_device(ts->idev);
- input_free_device(ts->idev);
kfree(ts);
dev_err(tsc->dev, "schedule failed");
goto err2;
}
+ platform_set_drvdata(pdev, tps6507x_dev);
return 0;
cancel_delayed_work_sync(&tsc->work);
destroy_workqueue(tsc->wq);
- input_free_device(input_dev);
+ input_unregister_device(input_dev);
tps6507x_dev->ts = NULL;
kfree(tsc);
const struct i2c_device_id *id)
{
struct tsc2007 *ts;
- struct tsc2007_platform_data *pdata = pdata = client->dev.platform_data;
+ struct tsc2007_platform_data *pdata = client->dev.platform_data;
struct input_dev *input_dev;
int err;
* Wacom W8001 penabled serial touchscreen driver
*
* Copyright (c) 2008 Jaya Kumar
+ * Copyright (c) 2010 Red Hat, Inc.
*
* This file is subject to the terms and conditions of the GNU General Public
* License. See the file COPYING in the main directory of this archive for
#define W8001_LEAD_BYTE 0x80
#define W8001_TAB_MASK 0x40
#define W8001_TAB_BYTE 0x40
+/* set in first byte of touch data packets */
+#define W8001_TOUCH_MASK (0x10 | W8001_LEAD_MASK)
+#define W8001_TOUCH_BYTE (0x10 | W8001_LEAD_BYTE)
#define W8001_QUERY_PACKET 0x20
#define W8001_CMD_START '1'
#define W8001_CMD_QUERY '*'
+#define W8001_CMD_TOUCHQUERY '%'
+
+/* length of data packets in bytes, depends on device. */
+#define W8001_PKTLEN_TOUCH93 5
+#define W8001_PKTLEN_TOUCH9A 7
+#define W8001_PKTLEN_TPCPEN 9
+#define W8001_PKTLEN_TPCCTL 11 /* control packet */
+#define W8001_PKTLEN_TOUCH2FG 13
+
+#define MAX_TRACKING_ID 0xFF /* arbitrarily chosen */
struct w8001_coord {
u8 rdy;
u8 tilt_y;
};
+/* touch query reply packet */
+struct w8001_touch_query {
+ u8 panel_res;
+ u8 capacity_res;
+ u8 sensor_id;
+ u16 x;
+ u16 y;
+};
+
/*
* Per-touchscreen data.
*/
unsigned char response[W8001_MAX_LENGTH];
unsigned char data[W8001_MAX_LENGTH];
char phys[32];
+ int type;
+ unsigned int pktlen;
+ int trkid[2];
};
static void parse_data(u8 *data, struct w8001_coord *coord)
coord->tilt_y = data[8] & 0x7F;
}
+static void parse_touch(struct w8001 *w8001)
+{
+ static int trkid;
+ struct input_dev *dev = w8001->dev;
+ unsigned char *data = w8001->data;
+ int i;
+
+ for (i = 0; i < 2; i++) {
+ input_mt_slot(dev, i);
+
+ if (data[0] & (1 << i)) {
+ int x = (data[6 * i + 1] << 7) | (data[6 * i + 2]);
+ int y = (data[6 * i + 3] << 7) | (data[6 * i + 4]);
+ /* data[5,6] and [11,12] is finger capacity */
+
+ input_report_abs(dev, ABS_MT_POSITION_X, x);
+ input_report_abs(dev, ABS_MT_POSITION_Y, y);
+ input_report_abs(dev, ABS_MT_TOOL_TYPE, MT_TOOL_FINGER);
+ if (w8001->trkid[i] < 0)
+ w8001->trkid[i] = trkid++ & MAX_TRACKING_ID;
+ } else {
+ w8001->trkid[i] = -1;
+ }
+ input_report_abs(dev, ABS_MT_TRACKING_ID, w8001->trkid[i]);
+ }
+
+ input_sync(dev);
+}
+
+static void parse_touchquery(u8 *data, struct w8001_touch_query *query)
+{
+ memset(query, 0, sizeof(*query));
+
+ query->panel_res = data[1];
+ query->sensor_id = data[2] & 0x7;
+ query->capacity_res = data[7];
+
+ query->x = data[3] << 9;
+ query->x |= data[4] << 2;
+ query->x |= (data[2] >> 5) & 0x3;
+
+ query->y = data[5] << 9;
+ query->y |= data[6] << 2;
+ query->y |= (data[2] >> 3) & 0x3;
+}
+
+static void report_pen_events(struct w8001 *w8001, struct w8001_coord *coord)
+{
+ struct input_dev *dev = w8001->dev;
+
+ /*
+ * We have 1 bit for proximity (rdy) and 3 bits for tip, side,
+ * side2/eraser. If rdy && f2 are set, this can be either pen + side2,
+ * or eraser. assume
+ * - if dev is already in proximity and f2 is toggled → pen + side2
+ * - if dev comes into proximity with f2 set → eraser
+ * If f2 disappears after assuming eraser, fake proximity out for
+ * eraser and in for pen.
+ */
+
+ if (!w8001->type) {
+ w8001->type = coord->f2 ? BTN_TOOL_RUBBER : BTN_TOOL_PEN;
+ } else if (w8001->type == BTN_TOOL_RUBBER) {
+ if (!coord->f2) {
+ input_report_abs(dev, ABS_PRESSURE, 0);
+ input_report_key(dev, BTN_TOUCH, 0);
+ input_report_key(dev, BTN_STYLUS, 0);
+ input_report_key(dev, BTN_STYLUS2, 0);
+ input_report_key(dev, BTN_TOOL_RUBBER, 0);
+ input_sync(dev);
+ w8001->type = BTN_TOOL_PEN;
+ }
+ } else {
+ input_report_key(dev, BTN_STYLUS2, coord->f2);
+ }
+
+ input_report_abs(dev, ABS_X, coord->x);
+ input_report_abs(dev, ABS_Y, coord->y);
+ input_report_abs(dev, ABS_PRESSURE, coord->pen_pressure);
+ input_report_key(dev, BTN_TOUCH, coord->tsw);
+ input_report_key(dev, BTN_STYLUS, coord->f1);
+ input_report_key(dev, w8001->type, coord->rdy);
+ input_sync(dev);
+
+ if (!coord->rdy)
+ w8001->type = 0;
+}
+
static irqreturn_t w8001_interrupt(struct serio *serio,
unsigned char data, unsigned int flags)
{
struct w8001 *w8001 = serio_get_drvdata(serio);
- struct input_dev *dev = w8001->dev;
struct w8001_coord coord;
unsigned char tmp;
}
break;
- case 8:
+ case W8001_PKTLEN_TOUCH93 - 1:
+ case W8001_PKTLEN_TOUCH9A - 1:
+ /* ignore one-finger touch packet. */
+ if (w8001->pktlen == w8001->idx)
+ w8001->idx = 0;
+ break;
+
+ /* Pen coordinates packet */
+ case W8001_PKTLEN_TPCPEN - 1:
tmp = w8001->data[0] & W8001_TAB_MASK;
if (unlikely(tmp == W8001_TAB_BYTE))
break;
+ tmp = (w8001->data[0] & W8001_TOUCH_BYTE);
+ if (tmp == W8001_TOUCH_BYTE)
+ break;
+
w8001->idx = 0;
parse_data(w8001->data, &coord);
- input_report_abs(dev, ABS_X, coord.x);
- input_report_abs(dev, ABS_Y, coord.y);
- input_report_abs(dev, ABS_PRESSURE, coord.pen_pressure);
- input_report_key(dev, BTN_TOUCH, coord.tsw);
- input_sync(dev);
+ report_pen_events(w8001, &coord);
break;
- case 10:
+ /* control packet */
+ case W8001_PKTLEN_TPCCTL - 1:
+ tmp = (w8001->data[0] & W8001_TOUCH_MASK);
+ if (tmp == W8001_TOUCH_BYTE)
+ break;
+
w8001->idx = 0;
memcpy(w8001->response, w8001->data, W8001_MAX_LENGTH);
w8001->response_type = W8001_QUERY_PACKET;
complete(&w8001->cmd_done);
break;
+
+ /* 2 finger touch packet */
+ case W8001_PKTLEN_TOUCH2FG - 1:
+ w8001->idx = 0;
+ parse_touch(w8001);
+ break;
}
return IRQ_HANDLED;
input_set_abs_params(dev, ABS_TILT_X, 0, coord.tilt_x, 0, 0);
input_set_abs_params(dev, ABS_TILT_Y, 0, coord.tilt_y, 0, 0);
+ error = w8001_command(w8001, W8001_CMD_TOUCHQUERY, true);
+ if (!error) {
+ struct w8001_touch_query touch;
+
+ parse_touchquery(w8001->response, &touch);
+
+ switch (touch.sensor_id) {
+ case 0:
+ case 2:
+ w8001->pktlen = W8001_PKTLEN_TOUCH93;
+ break;
+ case 1:
+ case 3:
+ case 4:
+ w8001->pktlen = W8001_PKTLEN_TOUCH9A;
+ break;
+ case 5:
+ w8001->pktlen = W8001_PKTLEN_TOUCH2FG;
+
+ input_mt_create_slots(dev, 2);
+ input_set_abs_params(dev, ABS_MT_TRACKING_ID,
+ 0, MAX_TRACKING_ID, 0, 0);
+ input_set_abs_params(dev, ABS_MT_POSITION_X,
+ 0, touch.x, 0, 0);
+ input_set_abs_params(dev, ABS_MT_POSITION_Y,
+ 0, touch.y, 0, 0);
+ input_set_abs_params(dev, ABS_MT_TOOL_TYPE,
+ 0, 0, 0, 0);
+ break;
+ }
+ }
+
return w8001_command(w8001, W8001_CMD_START, false);
}
w8001->serio = serio;
w8001->id = serio->id.id;
w8001->dev = input_dev;
+ w8001->trkid[0] = w8001->trkid[1] = -1;
init_completion(&w8001->cmd_done);
snprintf(w8001->phys, sizeof(w8001->phys), "%s/input0", serio->phys);
input_dev->evbit[0] = BIT_MASK(EV_KEY) | BIT_MASK(EV_ABS);
input_dev->keybit[BIT_WORD(BTN_TOUCH)] = BIT_MASK(BTN_TOUCH);
+ input_dev->keybit[BIT_WORD(BTN_TOOL_PEN)] |= BIT_MASK(BTN_TOOL_PEN);
+ input_dev->keybit[BIT_WORD(BTN_TOOL_RUBBER)] |= BIT_MASK(BTN_TOOL_RUBBER);
+ input_dev->keybit[BIT_WORD(BTN_STYLUS)] |= BIT_MASK(BTN_STYLUS);
+ input_dev->keybit[BIT_WORD(BTN_STYLUS2)] |= BIT_MASK(BTN_STYLUS2);
serio_set_drvdata(serio, w8001);
err = serio_open(serio, drv);
{
int power_adc = 0, auxval;
u16 power = 0;
+ int rc = 0;
+ int timeout = 0;
/* get codec */
mutex_lock(&wm->codec_mutex);
/* Turn polling mode on to read AUX ADC */
wm->pen_probably_down = 1;
- wm->codec->poll_sample(wm, adcsel, &auxval);
+
+ while (rc != RC_VALID && timeout++ < 5)
+ rc = wm->codec->poll_sample(wm, adcsel, &auxval);
if (power_adc)
wm97xx_reg_write(wm, AC97_EXTENDED_MID, power | 0x8000);
wm->pen_probably_down = 0;
+ if (timeout >= 5) {
+ dev_err(wm->dev,
+ "timeout reading auxadc %d, disabling digitiser\n",
+ adcsel);
+ wm->codec->dig_enable(wm, false);
+ }
+
mutex_unlock(&wm->codec_mutex);
- return auxval & 0xfff;
+ return (rc == RC_VALID ? auxval & 0xfff : -EBUSY);
}
EXPORT_SYMBOL_GPL(wm97xx_read_aux_adc);
touch_reg_err:
platform_device_put(wm->touch_dev);
touch_err:
- platform_device_unregister(wm->battery_dev);
- wm->battery_dev = NULL;
+ platform_device_del(wm->battery_dev);
batt_reg_err:
platform_device_put(wm->battery_dev);
batt_err:
/* FIXME: IR_KEYPRESS_TIMEOUT should be protocol specific */
#define IR_KEYPRESS_TIMEOUT 250
+/**
+ * ir_create_table() - initializes a scancode table
+ * @rc_tab: the ir_scancode_table to initialize
+ * @name: name to assign to the table
+ * @ir_type: ir type to assign to the new table
+ * @size: initial size of the table
+ * @return: zero on success or a negative error code
+ *
+ * This routine will initialize the ir_scancode_table and will allocate
+ * memory to hold at least the specified number elements.
+ */
+static int ir_create_table(struct ir_scancode_table *rc_tab,
+ const char *name, u64 ir_type, size_t size)
+{
+ rc_tab->name = name;
+ rc_tab->ir_type = ir_type;
+ rc_tab->alloc = roundup_pow_of_two(size * sizeof(struct ir_scancode));
+ rc_tab->size = rc_tab->alloc / sizeof(struct ir_scancode);
+ rc_tab->scan = kmalloc(rc_tab->alloc, GFP_KERNEL);
+ if (!rc_tab->scan)
+ return -ENOMEM;
+
+ IR_dprintk(1, "Allocated space for %u keycode entries (%u bytes)\n",
+ rc_tab->size, rc_tab->alloc);
+ return 0;
+}
+
+/**
+ * ir_free_table() - frees memory allocated by a scancode table
+ * @rc_tab: the table whose mappings need to be freed
+ *
+ * This routine will free memory alloctaed for key mappings used by given
+ * scancode table.
+ */
+static void ir_free_table(struct ir_scancode_table *rc_tab)
+{
+ rc_tab->size = 0;
+ kfree(rc_tab->scan);
+ rc_tab->scan = NULL;
+}
+
/**
* ir_resize_table() - resizes a scancode table if necessary
* @rc_tab: the ir_scancode_table to resize
+ * @gfp_flags: gfp flags to use when allocating memory
* @return: zero on success or a negative error code
*
* This routine will shrink the ir_scancode_table if it has lots of
* unused entries and grow it if it is full.
*/
-static int ir_resize_table(struct ir_scancode_table *rc_tab)
+static int ir_resize_table(struct ir_scancode_table *rc_tab, gfp_t gfp_flags)
{
unsigned int oldalloc = rc_tab->alloc;
unsigned int newalloc = oldalloc;
if (newalloc == oldalloc)
return 0;
- newscan = kmalloc(newalloc, GFP_ATOMIC);
+ newscan = kmalloc(newalloc, gfp_flags);
if (!newscan) {
IR_dprintk(1, "Failed to kmalloc %u bytes\n", newalloc);
return -ENOMEM;
}
/**
- * ir_do_setkeycode() - internal function to set a keycode in the
- * scancode->keycode table
+ * ir_update_mapping() - set a keycode in the scancode->keycode table
* @dev: the struct input_dev device descriptor
- * @rc_tab: the struct ir_scancode_table to set the keycode in
- * @scancode: the scancode for the ir command
- * @keycode: the keycode for the ir command
- * @resize: whether the keytable may be shrunk
- * @return: -EINVAL if the keycode could not be inserted, otherwise zero.
+ * @rc_tab: scancode table to be adjusted
+ * @index: index of the mapping that needs to be updated
+ * @keycode: the desired keycode
+ * @return: previous keycode assigned to the mapping
+ *
+ * This routine is used to update scancode->keycopde mapping at given
+ * position.
+ */
+static unsigned int ir_update_mapping(struct input_dev *dev,
+ struct ir_scancode_table *rc_tab,
+ unsigned int index,
+ unsigned int new_keycode)
+{
+ int old_keycode = rc_tab->scan[index].keycode;
+ int i;
+
+ /* Did the user wish to remove the mapping? */
+ if (new_keycode == KEY_RESERVED || new_keycode == KEY_UNKNOWN) {
+ IR_dprintk(1, "#%d: Deleting scan 0x%04x\n",
+ index, rc_tab->scan[index].scancode);
+ rc_tab->len--;
+ memmove(&rc_tab->scan[index], &rc_tab->scan[index+ 1],
+ (rc_tab->len - index) * sizeof(struct ir_scancode));
+ } else {
+ IR_dprintk(1, "#%d: %s scan 0x%04x with key 0x%04x\n",
+ index,
+ old_keycode == KEY_RESERVED ? "New" : "Replacing",
+ rc_tab->scan[index].scancode, new_keycode);
+ rc_tab->scan[index].keycode = new_keycode;
+ __set_bit(new_keycode, dev->keybit);
+ }
+
+ if (old_keycode != KEY_RESERVED) {
+ /* A previous mapping was updated... */
+ __clear_bit(old_keycode, dev->keybit);
+ /* ... but another scancode might use the same keycode */
+ for (i = 0; i < rc_tab->len; i++) {
+ if (rc_tab->scan[i].keycode == old_keycode) {
+ __set_bit(old_keycode, dev->keybit);
+ break;
+ }
+ }
+
+ /* Possibly shrink the keytable, failure is not a problem */
+ ir_resize_table(rc_tab, GFP_ATOMIC);
+ }
+
+ return old_keycode;
+}
+
+/**
+ * ir_locate_scancode() - set a keycode in the scancode->keycode table
+ * @ir_dev: the struct ir_input_dev device descriptor
+ * @rc_tab: scancode table to be searched
+ * @scancode: the desired scancode
+ * @resize: controls whether we allowed to resize the table to
+ * accomodate not yet present scancodes
+ * @return: index of the mapping containing scancode in question
+ * or -1U in case of failure.
*
- * This routine is used internally to manipulate the scancode->keycode table.
- * The caller has to hold @rc_tab->lock.
+ * This routine is used to locate given scancode in ir_scancode_table.
+ * If scancode is not yet present the routine will allocate a new slot
+ * for it.
*/
-static int ir_do_setkeycode(struct input_dev *dev,
- struct ir_scancode_table *rc_tab,
- unsigned scancode, unsigned keycode,
- bool resize)
+static unsigned int ir_establish_scancode(struct ir_input_dev *ir_dev,
+ struct ir_scancode_table *rc_tab,
+ unsigned int scancode,
+ bool resize)
{
unsigned int i;
- int old_keycode = KEY_RESERVED;
- struct ir_input_dev *ir_dev = input_get_drvdata(dev);
/*
* Unfortunately, some hardware-based IR decoders don't provide
* the provided IR with another one, it is needed to allow loading
* IR tables from other remotes. So,
*/
- if (ir_dev->props && ir_dev->props->scanmask) {
+ if (ir_dev->props && ir_dev->props->scanmask)
scancode &= ir_dev->props->scanmask;
- }
/* First check if we already have a mapping for this ir command */
for (i = 0; i < rc_tab->len; i++) {
+ if (rc_tab->scan[i].scancode == scancode)
+ return i;
+
/* Keytable is sorted from lowest to highest scancode */
- if (rc_tab->scan[i].scancode > scancode)
+ if (rc_tab->scan[i].scancode >= scancode)
break;
- else if (rc_tab->scan[i].scancode < scancode)
- continue;
-
- old_keycode = rc_tab->scan[i].keycode;
- rc_tab->scan[i].keycode = keycode;
-
- /* Did the user wish to remove the mapping? */
- if (keycode == KEY_RESERVED || keycode == KEY_UNKNOWN) {
- IR_dprintk(1, "#%d: Deleting scan 0x%04x\n",
- i, scancode);
- rc_tab->len--;
- memmove(&rc_tab->scan[i], &rc_tab->scan[i + 1],
- (rc_tab->len - i) * sizeof(struct ir_scancode));
- }
-
- /* Possibly shrink the keytable, failure is not a problem */
- ir_resize_table(rc_tab);
- break;
}
- if (old_keycode == KEY_RESERVED && keycode != KEY_RESERVED) {
- /* No previous mapping found, we might need to grow the table */
- if (resize && ir_resize_table(rc_tab))
- return -ENOMEM;
-
- IR_dprintk(1, "#%d: New scan 0x%04x with key 0x%04x\n",
- i, scancode, keycode);
+ /* No previous mapping found, we might need to grow the table */
+ if (rc_tab->size == rc_tab->len) {
+ if (!resize || ir_resize_table(rc_tab, GFP_ATOMIC))
+ return -1U;
+ }
- /* i is the proper index to insert our new keycode */
+ /* i is the proper index to insert our new keycode */
+ if (i < rc_tab->len)
memmove(&rc_tab->scan[i + 1], &rc_tab->scan[i],
(rc_tab->len - i) * sizeof(struct ir_scancode));
- rc_tab->scan[i].scancode = scancode;
- rc_tab->scan[i].keycode = keycode;
- rc_tab->len++;
- set_bit(keycode, dev->keybit);
- } else {
- IR_dprintk(1, "#%d: Replacing scan 0x%04x with key 0x%04x\n",
- i, scancode, keycode);
- /* A previous mapping was updated... */
- clear_bit(old_keycode, dev->keybit);
- /* ...but another scancode might use the same keycode */
- for (i = 0; i < rc_tab->len; i++) {
- if (rc_tab->scan[i].keycode == old_keycode) {
- set_bit(old_keycode, dev->keybit);
- break;
- }
- }
- }
+ rc_tab->scan[i].scancode = scancode;
+ rc_tab->scan[i].keycode = KEY_RESERVED;
+ rc_tab->len++;
- return 0;
+ return i;
}
/**
* This routine is used to handle evdev EVIOCSKEY ioctl.
*/
static int ir_setkeycode(struct input_dev *dev,
- unsigned int scancode, unsigned int keycode)
+ const struct input_keymap_entry *ke,
+ unsigned int *old_keycode)
{
- int rc;
- unsigned long flags;
struct ir_input_dev *ir_dev = input_get_drvdata(dev);
struct ir_scancode_table *rc_tab = &ir_dev->rc_tab;
+ unsigned int index;
+ unsigned int scancode;
+ int retval;
+ unsigned long flags;
spin_lock_irqsave(&rc_tab->lock, flags);
- rc = ir_do_setkeycode(dev, rc_tab, scancode, keycode, true);
+
+ if (ke->flags & INPUT_KEYMAP_BY_INDEX) {
+ index = ke->index;
+ if (index >= rc_tab->len) {
+ retval = -EINVAL;
+ goto out;
+ }
+ } else {
+ retval = input_scancode_to_scalar(ke, &scancode);
+ if (retval)
+ goto out;
+
+ index = ir_establish_scancode(ir_dev, rc_tab, scancode, true);
+ if (index >= rc_tab->len) {
+ retval = -ENOMEM;
+ goto out;
+ }
+ }
+
+ *old_keycode = ir_update_mapping(dev, rc_tab, index, ke->keycode);
+
+out:
spin_unlock_irqrestore(&rc_tab->lock, flags);
- return rc;
+ return retval;
}
/**
* @dev: the struct input_dev device descriptor
* @to: the struct ir_scancode_table to copy entries to
* @from: the struct ir_scancode_table to copy entries from
- * @return: -EINVAL if all keycodes could not be inserted, otherwise zero.
+ * @return: -ENOMEM if all keycodes could not be inserted, otherwise zero.
*
* This routine is used to handle table initialization.
*/
-static int ir_setkeytable(struct input_dev *dev,
- struct ir_scancode_table *to,
+static int ir_setkeytable(struct ir_input_dev *ir_dev,
const struct ir_scancode_table *from)
{
- struct ir_input_dev *ir_dev = input_get_drvdata(dev);
struct ir_scancode_table *rc_tab = &ir_dev->rc_tab;
- unsigned long flags;
- unsigned int i;
- int rc = 0;
+ unsigned int i, index;
+ int rc;
+
+ rc = ir_create_table(&ir_dev->rc_tab,
+ from->name, from->ir_type, from->size);
+ if (rc)
+ return rc;
+
+ IR_dprintk(1, "Allocated space for %u keycode entries (%u bytes)\n",
+ rc_tab->size, rc_tab->alloc);
- spin_lock_irqsave(&rc_tab->lock, flags);
for (i = 0; i < from->size; i++) {
- rc = ir_do_setkeycode(dev, to, from->scan[i].scancode,
- from->scan[i].keycode, false);
- if (rc)
+ index = ir_establish_scancode(ir_dev, rc_tab,
+ from->scan[i].scancode, false);
+ if (index >= rc_tab->len) {
+ rc = -ENOMEM;
break;
+ }
+
+ ir_update_mapping(ir_dev->input_dev, rc_tab, index,
+ from->scan[i].keycode);
}
- spin_unlock_irqrestore(&rc_tab->lock, flags);
+
+ if (rc)
+ ir_free_table(rc_tab);
+
return rc;
}
+/**
+ * ir_lookup_by_scancode() - locate mapping by scancode
+ * @rc_tab: the &struct ir_scancode_table to search
+ * @scancode: scancode to look for in the table
+ * @return: index in the table, -1U if not found
+ *
+ * This routine performs binary search in RC keykeymap table for
+ * given scancode.
+ */
+static unsigned int ir_lookup_by_scancode(const struct ir_scancode_table *rc_tab,
+ unsigned int scancode)
+{
+ unsigned int start = 0;
+ unsigned int end = rc_tab->len - 1;
+ unsigned int mid;
+
+ while (start <= end) {
+ mid = (start + end) / 2;
+ if (rc_tab->scan[mid].scancode < scancode)
+ start = mid + 1;
+ else if (rc_tab->scan[mid].scancode > scancode)
+ end = mid - 1;
+ else
+ return mid;
+ }
+
+ return -1U;
+}
+
/**
* ir_getkeycode() - get a keycode from the scancode->keycode table
* @dev: the struct input_dev device descriptor
* This routine is used to handle evdev EVIOCGKEY ioctl.
*/
static int ir_getkeycode(struct input_dev *dev,
- unsigned int scancode, unsigned int *keycode)
+ struct input_keymap_entry *ke)
{
- int start, end, mid;
- unsigned long flags;
- int key = KEY_RESERVED;
struct ir_input_dev *ir_dev = input_get_drvdata(dev);
struct ir_scancode_table *rc_tab = &ir_dev->rc_tab;
+ struct ir_scancode *entry;
+ unsigned long flags;
+ unsigned int index;
+ unsigned int scancode;
+ int retval;
spin_lock_irqsave(&rc_tab->lock, flags);
- start = 0;
- end = rc_tab->len - 1;
- while (start <= end) {
- mid = (start + end) / 2;
- if (rc_tab->scan[mid].scancode < scancode)
- start = mid + 1;
- else if (rc_tab->scan[mid].scancode > scancode)
- end = mid - 1;
- else {
- key = rc_tab->scan[mid].keycode;
- break;
- }
+
+ if (ke->flags & INPUT_KEYMAP_BY_INDEX) {
+ index = ke->index;
+ } else {
+ retval = input_scancode_to_scalar(ke, &scancode);
+ if (retval)
+ goto out;
+
+ index = ir_lookup_by_scancode(rc_tab, scancode);
+ }
+
+ if (index >= rc_tab->len) {
+ if (!(ke->flags & INPUT_KEYMAP_BY_INDEX))
+ IR_dprintk(1, "unknown key for scancode 0x%04x\n",
+ scancode);
+ retval = -EINVAL;
+ goto out;
}
- spin_unlock_irqrestore(&rc_tab->lock, flags);
- if (key == KEY_RESERVED)
- IR_dprintk(1, "unknown key for scancode 0x%04x\n",
- scancode);
+ entry = &rc_tab->scan[index];
- *keycode = key;
- return 0;
+ ke->index = index;
+ ke->keycode = entry->keycode;
+ ke->len = sizeof(entry->scancode);
+ memcpy(ke->scancode, &entry->scancode, sizeof(entry->scancode));
+
+out:
+ spin_unlock_irqrestore(&rc_tab->lock, flags);
+ return retval;
}
/**
*/
u32 ir_g_keycode_from_table(struct input_dev *dev, u32 scancode)
{
- int keycode;
+ struct ir_input_dev *ir_dev = input_get_drvdata(dev);
+ struct ir_scancode_table *rc_tab = &ir_dev->rc_tab;
+ unsigned int keycode;
+ unsigned int index;
+ unsigned long flags;
+
+ spin_lock_irqsave(&rc_tab->lock, flags);
+
+ index = ir_lookup_by_scancode(rc_tab, scancode);
+ keycode = index < rc_tab->len ?
+ rc_tab->scan[index].keycode : KEY_RESERVED;
+
+ spin_unlock_irqrestore(&rc_tab->lock, flags);
- ir_getkeycode(dev, scancode, &keycode);
if (keycode != KEY_RESERVED)
IR_dprintk(1, "%s: scancode 0x%04x keycode 0x%02x\n",
dev->name, scancode, keycode);
+
return keycode;
}
EXPORT_SYMBOL_GPL(ir_g_keycode_from_table);
goto out_dev;
}
- input_dev->getkeycode = ir_getkeycode;
- input_dev->setkeycode = ir_setkeycode;
+ input_dev->getkeycode_new = ir_getkeycode;
+ input_dev->setkeycode_new = ir_setkeycode;
input_set_drvdata(input_dev, ir_dev);
ir_dev->input_dev = input_dev;
spin_lock_init(&ir_dev->keylock);
setup_timer(&ir_dev->timer_keyup, ir_timer_keyup, (unsigned long)ir_dev);
- ir_dev->rc_tab.name = rc_tab->name;
- ir_dev->rc_tab.ir_type = rc_tab->ir_type;
- ir_dev->rc_tab.alloc = roundup_pow_of_two(rc_tab->size *
- sizeof(struct ir_scancode));
- ir_dev->rc_tab.scan = kmalloc(ir_dev->rc_tab.alloc, GFP_KERNEL);
- ir_dev->rc_tab.size = ir_dev->rc_tab.alloc / sizeof(struct ir_scancode);
if (props) {
ir_dev->props = props;
if (props->open)
input_dev->close = ir_close;
}
- if (!ir_dev->rc_tab.scan) {
- rc = -ENOMEM;
- goto out_name;
- }
-
- IR_dprintk(1, "Allocated space for %u keycode entries (%u bytes)\n",
- ir_dev->rc_tab.size, ir_dev->rc_tab.alloc);
-
set_bit(EV_KEY, input_dev->evbit);
set_bit(EV_REP, input_dev->evbit);
set_bit(EV_MSC, input_dev->evbit);
set_bit(MSC_SCAN, input_dev->mscbit);
- if (ir_setkeytable(input_dev, &ir_dev->rc_tab, rc_tab)) {
- rc = -ENOMEM;
- goto out_table;
- }
+ rc = ir_setkeytable(ir_dev, rc_tab);
+ if (rc)
+ goto out_name;
rc = ir_register_class(input_dev);
if (rc < 0)
out_event:
ir_unregister_class(input_dev);
out_table:
- kfree(ir_dev->rc_tab.scan);
+ ir_free_table(&ir_dev->rc_tab);
out_name:
kfree(ir_dev->driver_name);
out_dev:
void ir_input_unregister(struct input_dev *input_dev)
{
struct ir_input_dev *ir_dev = input_get_drvdata(input_dev);
- struct ir_scancode_table *rc_tab;
if (!ir_dev)
return;
if (ir_dev->props->driver_type == RC_DRIVER_IR_RAW)
ir_raw_event_unregister(input_dev);
- rc_tab = &ir_dev->rc_tab;
- rc_tab->size = 0;
- kfree(rc_tab->scan);
- rc_tab->scan = NULL;
+ ir_free_table(&ir_dev->rc_tab);
ir_unregister_class(input_dev);
},
};
+static struct resource ab8500_poweronkey_db_resources[] = {
+ {
+ .name = "ONKEY_DBF",
+ .start = AB8500_INT_PON_KEY1DB_F,
+ .end = AB8500_INT_PON_KEY1DB_F,
+ .flags = IORESOURCE_IRQ,
+ },
+ {
+ .name = "ONKEY_DBR",
+ .start = AB8500_INT_PON_KEY1DB_R,
+ .end = AB8500_INT_PON_KEY1DB_R,
+ .flags = IORESOURCE_IRQ,
+ },
+};
+
static struct mfd_cell ab8500_devs[] = {
{
.name = "ab8500-gpadc",
{ .name = "ab8500-usb", },
{ .name = "ab8500-pwm", },
{ .name = "ab8500-regulator", },
+ {
+ .name = "ab8500-poweron-key",
+ .num_resources = ARRAY_SIZE(ab8500_poweronkey_db_resources),
+ .resources = ab8500_poweronkey_db_resources,
+ },
};
int __devinit ab8500_init(struct ab8500 *ab8500)
source "drivers/staging/xgifb/Kconfig"
-source "drivers/staging/mrst-touchscreen/Kconfig"
-
source "drivers/staging/msm/Kconfig"
source "drivers/staging/lirc/Kconfig"
obj-$(CONFIG_TI_ST) += ti-st/
obj-$(CONFIG_ADIS16255) += adis16255/
obj-$(CONFIG_FB_XGI) += xgifb/
-obj-$(CONFIG_TOUCHSCREEN_MRSTOUCH) += mrst-touchscreen/
obj-$(CONFIG_MSM_STAGING) += msm/
obj-$(CONFIG_EASYCAP) += easycap/
obj-$(CONFIG_SOLO6X10) += solo6x10/
+++ /dev/null
-config TOUCHSCREEN_INTEL_MID
- tristate "Intel MID platform resistive touchscreen"
- depends on INTEL_SCU_IPC
- default y
- help
- Say Y here if you have a Intel MID based touchscreen
- If unsure, say N.
+++ /dev/null
-obj-$(CONFIG_TOUCHSCREEN_INTEL_MID) := intel_mid_touch.o
-
-
+++ /dev/null
-- Move the driver to not think it is SPI (requires fixing some of the SFI
- and firmware side)
+++ /dev/null
-/*
- * intel_mid_touch.c - Intel MID Resistive Touch Screen Driver
- *
- * Copyright (C) 2008 Intel Corp
- *
- * ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License as published by
- * the Free Software Foundation; version 2 of the License.
- *
- * This program is distributed in the hope that it will be useful, but
- * WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU
- * General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License along
- * with this program; ifnot, write to the Free Software Foundation, Inc.,
- * 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA.
- *
- * Questions/Comments/Bug fixes to Sreedhara (sreedhara.ds@intel.com)
- * Ramesh Agarwal (ramesh.agarwal@intel.com)
- * ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
- *
- * TODO:
- * kill off mrstouch_debug eventually
- * review conversion of r/m/w sequences
- * Replace interrupt mutex abuse
- * Kill of mrstouchdevp pointer
- *
- */
-
-#include <linux/module.h>
-#include <linux/init.h>
-#include <linux/input.h>
-#include <linux/interrupt.h>
-#include <linux/err.h>
-#include <linux/param.h>
-#include <linux/spi/spi.h>
-#include <linux/irq.h>
-#include <linux/delay.h>
-#include <linux/kthread.h>
-#include <asm/intel_scu_ipc.h>
-
-
-#if defined(MRSTOUCH_DEBUG)
-#define mrstouch_debug(fmt, args...)\
- do { \
- printk(KERN_DEBUG "\n[MRSTOUCH(%d)] - ", __LINE__); \
- printk(KERN_DEBUG fmt, ##args); \
- } while (0);
-#else
-#define mrstouch_debug(fmt, args...)
-#endif
-
-/* PMIC Interrupt registers */
-#define PMIC_REG_ID1 0x00 /*PMIC ID1 register */
-
-/* PMIC Interrupt registers */
-#define PMIC_REG_INT 0x04 /*PMIC interrupt register */
-#define PMIC_REG_MINT 0x05 /*PMIC interrupt mask register */
-
-/* ADC Interrupt registers */
-#define PMIC_REG_ADCINT 0x5F /*ADC interrupt register */
-#define PMIC_REG_MADCINT 0x60 /*ADC interrupt mask register */
-
-/* ADC Control registers */
-#define PMIC_REG_ADCCNTL1 0x61 /*ADC control register */
-
-/* ADC Channel Selection registers */
-#define PMICADDR0 0xA4
-#define END_OF_CHANNEL 0x1F
-
-/* ADC Result register */
-#define PMIC_REG_ADCSNS0H 0x64
-
-/* ADC channels for touch screen */
-#define MRST_TS_CHAN10 0xA /* Touch screen X+ connection */
-#define MRST_TS_CHAN11 0xB /* Touch screen X- connection */
-#define MRST_TS_CHAN12 0xC /* Touch screen Y+ connection */
-#define MRST_TS_CHAN13 0xD /* Touch screen Y- connection */
-
-/* Touch screen coordinate constants */
-#define TOUCH_PRESSURE 50
-#define TOUCH_PRESSURE_FS 100
-
-#define XMOVE_LIMIT 5
-#define YMOVE_LIMIT 5
-#define XYMOVE_CNT 3
-
-#define MAX_10BIT ((1<<10)-1)
-
-/* Touch screen channel BIAS constants */
-#define XBIAS 0x20
-#define YBIAS 0x40
-#define ZBIAS 0x80
-
-/* Touch screen coordinates */
-#define MIN_X 10
-#define MAX_X 1024
-#define MIN_Y 10
-#define MAX_Y 1024
-#define WAIT_ADC_COMPLETION 10
-
-/* PMIC ADC round robin delays */
-#define ADC_LOOP_DELAY0 0x0 /* Continuous loop */
-#define ADC_LOOP_DELAY1 0x1 /* 4.5 ms approximate */
-
-/* PMIC Vendor Identifiers */
-#define PMIC_VENDOR_FS 0 /* PMIC vendor FreeScale */
-#define PMIC_VENDOR_MAXIM 1 /* PMIC vendor MAXIM */
-#define PMIC_VENDOR_NEC 2 /* PMIC vendor NEC */
-#define MRSTOUCH_MAX_CHANNELS 32 /* Maximum ADC channels */
-
-/* Touch screen device structure */
-struct mrstouch_dev {
- struct spi_device *spi; /* SPI device associated with touch screen */
- struct input_dev *input; /* input device for touchscreen*/
- char phys[32]; /* Device name */
- struct task_struct *pendet_thrd; /* PENDET interrupt handler */
- struct mutex lock; /* Sync between interrupt and PENDET handler */
- bool busy; /* Busy flag */
- u16 asr; /* Address selection register */
- int irq; /* Touch screen IRQ # */
- uint vendor; /* PMIC vendor */
- uint rev; /* PMIC revision */
- bool suspended; /* Device suspended status */
- bool disabled; /* Device disabled status */
- u16 x; /* X coordinate */
- u16 y; /* Y coordinate */
- bool pendown; /* PEN position */
-} ;
-
-
-/* Global Pointer to Touch screen device */
-static struct mrstouch_dev *mrstouchdevp;
-
-/* Utility to read PMIC ID */
-static int mrstouch_pmic_id(uint *vendor, uint *rev)
-{
- int err;
- u8 r;
-
- err = intel_scu_ipc_ioread8(PMIC_REG_ID1, &r);
- if (err)
- return err;
-
- *vendor = r & 0x7;
- *rev = (r >> 3) & 0x7;
-
- return 0;
-}
-
-/*
- * Parse ADC channels to find end of the channel configured by other ADC user
- * NEC and MAXIM requires 4 channels and FreeScale needs 18 channels
- */
-static int mrstouch_chan_parse(struct mrstouch_dev *tsdev)
-{
- int err, i, j, found;
- u32 r32;
-
- found = -1;
-
- for (i = 0; i < MRSTOUCH_MAX_CHANNELS; i++) {
- if (found >= 0)
- break;
-
- err = intel_scu_ipc_ioread32(PMICADDR0, &r32);
- if (err)
- return err;
-
- for (j = 0; j < 32; j+= 8) {
- if (((r32 >> j) & 0xFF) == END_OF_CHANNEL) {
- found = i;
- break;
- }
- }
- }
- if (found < 0)
- return 0;
-
- if (tsdev->vendor == PMIC_VENDOR_FS) {
- if (found && found > (MRSTOUCH_MAX_CHANNELS - 18))
- return -ENOSPC;
- } else {
- if (found && found > (MRSTOUCH_MAX_CHANNELS - 4))
- return -ENOSPC;
- }
- return found;
-}
-
-/* Utility to enable/disable pendet.
- * pendet set to true enables PENDET interrupt
- * pendet set to false disables PENDET interrupt
- * Also clears RND mask bit
-*/
-static int pendet_enable(struct mrstouch_dev *tsdev, bool pendet)
-{
- u16 reg;
- u8 r;
- u8 pendet_enabled = 0;
- int retry = 0;
- int err;
-
- err = intel_scu_ipc_ioread16(PMIC_REG_MADCINT, ®);
- if (err)
- return err;
-
- if (pendet) {
- reg &= ~0x0005;
- reg |= 0x2000; /* Enable pendet */
- } else
- reg &= 0xDFFF; /* Disable pendet */
-
- /* Set MADCINT and update ADCCNTL1 (next reg byte) */
- err = intel_scu_ipc_iowrite16(PMIC_REG_MADCINT, reg);
- if (!pendet || err)
- return err;
-
- /*
- * Sometimes even after the register write succeeds
- * the PMIC register value is not updated. Retry few iterations
- * to enable pendet.
- */
-
- err = intel_scu_ipc_ioread8(PMIC_REG_ADCCNTL1, &r);
- pendet_enabled = (r >> 5) & 0x01;
-
- retry = 0;
- while (!err && !pendet_enabled) {
- retry++;
- msleep(10);
- err = intel_scu_ipc_iowrite8(PMIC_REG_ADCCNTL1, reg >> 8);
- if (err)
- break;
- err = intel_scu_ipc_ioread8(PMIC_REG_ADCCNTL1, &r);
- if (err == 0)
- pendet_enabled = (r >> 5) & 0x01;
- if (retry >= 10) {
- dev_err(&tsdev->spi->dev, "Touch screen disabled.\n");
- return -EIO;
- }
- }
- return 0;
-}
-
-/* To read PMIC ADC touch screen result
- * Reads ADC storage registers for higher 7 and lower 3 bits
- * converts the two readings to single value and turns off gain bit
- */
-static int mrstouch_ts_chan_read(u16 offset, u16 chan, u16 *vp, u16 *vm)
-{
- int err;
- u16 result;
- u32 res;
-
- result = PMIC_REG_ADCSNS0H + offset;
-
- if (chan == MRST_TS_CHAN12)
- result += 4;
-
- err = intel_scu_ipc_ioread32(result, &res);
- if (err)
- return err;
-
- /* Mash the bits up */
-
- *vp = (res & 0xFF) << 3; /* Highest 7 bits */
- *vp |= (res >> 8) & 0x07; /* Lower 3 bits */
- *vp &= 0x3FF;
-
- res >>= 16;
-
- *vm = (res & 0xFF) << 3; /* Highest 7 bits */
- *vm |= (res >> 8) & 0x07; /* Lower 3 bits */
- *vm &= 0x3FF;
-
- return 0;
-}
-
-/* To configure touch screen channels
- * Writes touch screen channels to ADC address selection registers
- */
-static int mrstouch_ts_chan_set(uint offset)
-{
- int count;
- u16 chan;
- u16 reg[5];
- u8 data[5];
-
- chan = PMICADDR0 + offset;
- for (count = 0; count <= 3; count++) {
- reg[count] = chan++;
- data[count] = MRST_TS_CHAN10 + count;
- }
- reg[count] = chan;
- data[count] = END_OF_CHANNEL;
-
- return intel_scu_ipc_writev(reg, data, 5);
-}
-
-/* Initialize ADC */
-static int mrstouch_adc_init(struct mrstouch_dev *tsdev)
-{
- int err, start;
- u8 ra, rm;
-
- err = mrstouch_pmic_id(&tsdev->vendor, &tsdev->rev);
- if (err) {
- dev_err(&tsdev->spi->dev, "Unable to read PMIC id\n");
- return err;
- }
-
- start = mrstouch_chan_parse(tsdev);
- if (start < 0) {
- dev_err(&tsdev->spi->dev, "Unable to parse channels\n");
- return start;
- }
-
- tsdev->asr = start;
-
- mrstouch_debug("Channel offset(%d): 0x%X\n", tsdev->asr, tsdev->vendor);
-
- /* ADC power on, start, enable PENDET and set loop delay
- * ADC loop delay is set to 4.5 ms approximately
- * Loop delay more than this results in jitter in adc readings
- * Setting loop delay to 0 (continous loop) in MAXIM stops PENDET
- * interrupt generation sometimes.
- */
-
- if (tsdev->vendor == PMIC_VENDOR_FS) {
- ra = 0xE0 | ADC_LOOP_DELAY0;
- rm = 0x5;
- } else {
- /* NEC and MAXIm not consistent with loop delay 0 */
- ra = 0xE0 | ADC_LOOP_DELAY1;
- rm = 0x0;
-
- /* configure touch screen channels */
- err = mrstouch_ts_chan_set(tsdev->asr);
- if (err)
- return err;
- }
- err = intel_scu_ipc_update_register(PMIC_REG_ADCCNTL1, ra, 0xE7);
- if (err == 0)
- err = intel_scu_ipc_update_register(PMIC_REG_MADCINT, rm, 0x03);
- return err;
-}
-
-/* Reports x,y coordinates to event subsystem */
-static void mrstouch_report_xy(struct mrstouch_dev *tsdev, u16 x, u16 y, u16 z)
-{
- int xdiff, ydiff;
-
- if (tsdev->pendown && z <= TOUCH_PRESSURE) {
- /* Pen removed, report button release */
- mrstouch_debug("BTN REL(%d)", z);
- input_report_key(tsdev->input, BTN_TOUCH, 0);
- tsdev->pendown = false;
- }
-
- xdiff = abs(x - tsdev->x);
- ydiff = abs(y - tsdev->y);
-
- /*
- if x and y values changes for XYMOVE_CNT readings it is considered
- as stylus is moving. This is required to differentiate between stylus
- movement and jitter
- */
- if (x < MIN_X || x > MAX_X || y < MIN_Y || y > MAX_Y) {
- /* Spurious values, release button if touched and return */
- if (tsdev->pendown) {
- mrstouch_debug("BTN REL(%d)", z);
- input_report_key(tsdev->input, BTN_TOUCH, 0);
- tsdev->pendown = false;
- }
- return;
- } else if (xdiff >= XMOVE_LIMIT || ydiff >= YMOVE_LIMIT) {
- tsdev->x = x;
- tsdev->y = y;
-
- input_report_abs(tsdev->input, ABS_X, x);
- input_report_abs(tsdev->input, ABS_Y, y);
- input_sync(tsdev->input);
- }
-
-
- if (!tsdev->pendown && z > TOUCH_PRESSURE) {
- /* Pen touched, report button touch */
- mrstouch_debug("BTN TCH(%d, %d, %d)", x, y, z);
- input_report_key(tsdev->input, BTN_TOUCH, 1);
- tsdev->pendown = true;
- }
-}
-
-
-/* Utility to start ADC, used by freescale handler */
-static int pendet_mask(void)
-{
- return intel_scu_ipc_update_register(PMIC_REG_MADCINT, 0x02, 0x02);
-}
-
-/* Utility to stop ADC, used by freescale handler */
-static int pendet_umask(void)
-{
- return intel_scu_ipc_update_register(PMIC_REG_MADCINT, 0x00, 0x02);
-}
-
-/* Utility to read ADC, used by freescale handler */
-static int mrstouch_pmic_fs_adc_read(struct mrstouch_dev *tsdev)
-{
- int err;
- u16 x, y, z, result;
- u16 reg[4];
- u8 data[4];
-
- result = PMIC_REG_ADCSNS0H + tsdev->asr;
-
- reg[0] = result + 4;
- reg[1] = result + 5;
- reg[2] = result + 16;
- reg[3] = result + 17;
-
- err = intel_scu_ipc_readv(reg, data, 4);
- if (err)
- goto ipc_error;
-
- x = data[0] << 3; /* Higher 7 bits */
- x |= data[1] & 0x7; /* Lower 3 bits */
- x &= 0x3FF;
-
- y = data[2] << 3; /* Higher 7 bits */
- y |= data[3] & 0x7; /* Lower 3 bits */
- y &= 0x3FF;
-
- /* Read Z value */
- reg[0] = result + 28;
- reg[1] = result + 29;
-
- err = intel_scu_ipc_readv(reg, data, 4);
- if (err)
- goto ipc_error;
-
- z = data[0] << 3; /* Higher 7 bits */
- z |= data[1] & 0x7; /* Lower 3 bits */
- z &= 0x3FF;
-
-#if defined(MRSTOUCH_PRINT_XYZP)
- mrstouch_debug("X: %d, Y: %d, Z: %d", x, y, z);
-#endif
-
- if (z >= TOUCH_PRESSURE_FS) {
- mrstouch_report_xy(tsdev, x, y, TOUCH_PRESSURE - 1); /* Pen Removed */
- return TOUCH_PRESSURE - 1;
- } else {
- mrstouch_report_xy(tsdev, x, y, TOUCH_PRESSURE + 1); /* Pen Touched */
- return TOUCH_PRESSURE + 1;
- }
-
- return 0;
-
-ipc_error:
- dev_err(&tsdev->spi->dev, "ipc error during fs_adc read\n");
- return err;
-}
-
-/* To handle free scale pmic pendet interrupt */
-static int pmic0_pendet(void *dev_id)
-{
- int err, count;
- u16 chan;
- unsigned int touched;
- struct mrstouch_dev *tsdev = (struct mrstouch_dev *)dev_id;
- u16 reg[5];
- u8 data[5];
-
- chan = PMICADDR0 + tsdev->asr;
-
- /* Set X BIAS */
- for (count = 0; count <= 3; count++) {
- reg[count] = chan++;
- data[count] = 0x2A;
- }
- reg[count] = chan++; /* Dummy */
- data[count] = 0;
-
- err = intel_scu_ipc_writev(reg, data, 5);
- if (err)
- goto ipc_error;
-
- msleep(WAIT_ADC_COMPLETION);
-
- /* Set Y BIAS */
- for (count = 0; count <= 3; count++) {
- reg[count] = chan++;
- data[count] = 0x4A;
- }
- reg[count] = chan++; /* Dummy */
- data[count] = 0;
-
- err = intel_scu_ipc_writev(reg, data, 5);
- if (err)
- goto ipc_error;
-
- msleep(WAIT_ADC_COMPLETION);
-
- /* Set Z BIAS */
- err = intel_scu_ipc_iowrite32(chan + 2, 0x8A8A8A8A);
- if (err)
- goto ipc_error;
-
- msleep(WAIT_ADC_COMPLETION);
-
- /*Read touch screen channels till pen removed
- * Freescale reports constant value of z for all points
- * z is high when screen is not touched and low when touched
- * Map high z value to not touched and low z value to pen touched
- */
- touched = mrstouch_pmic_fs_adc_read(tsdev);
- while (touched > TOUCH_PRESSURE) {
- touched = mrstouch_pmic_fs_adc_read(tsdev);
- msleep(WAIT_ADC_COMPLETION);
- }
-
- /* Clear all TS channels */
- chan = PMICADDR0 + tsdev->asr;
- for (count = 0; count <= 4; count++) {
- reg[count] = chan++;
- data[count] = 0;
- }
- err = intel_scu_ipc_writev(reg, data, 5);
- if (err)
- goto ipc_error;
-
- for (count = 0; count <= 4; count++) {
- reg[count] = chan++;
- data[count] = 0;
- }
- err = intel_scu_ipc_writev(reg, data, 5);
- if (err)
- goto ipc_error;
-
- err = intel_scu_ipc_iowrite32(chan + 2, 0x00000000);
- if (err)
- goto ipc_error;
-
- return 0;
-
-ipc_error:
- dev_err(&tsdev->spi->dev, "ipc error during pendet\n");
- return err;
-}
-
-
-/* To enable X, Y and Z bias values
- * Enables YPYM for X channels and XPXM for Y channels
- */
-static int mrstouch_ts_bias_set(uint offset, uint bias)
-{
- int count;
- u16 chan, start;
- u16 reg[4];
- u8 data[4];
-
- chan = PMICADDR0 + offset;
- start = MRST_TS_CHAN10;
-
- for (count = 0; count <= 3; count++) {
- reg[count] = chan++;
- data[count] = bias | (start + count);
- }
- return intel_scu_ipc_writev(reg, data, 4);
-}
-
-/* To read touch screen channel values */
-static int mrstouch_adc_read(struct mrstouch_dev *tsdev)
-{
- int err;
- u16 xp, xm, yp, ym, zp, zm;
-
- /* configure Y bias for X channels */
- err = mrstouch_ts_bias_set(tsdev->asr, YBIAS);
- if (err)
- goto ipc_error;
-
- msleep(WAIT_ADC_COMPLETION);
-
- /* read x+ and x- channels */
- err = mrstouch_ts_chan_read(tsdev->asr, MRST_TS_CHAN10, &xp, &xm);
- if (err)
- goto ipc_error;
-
- /* configure x bias for y channels */
- err = mrstouch_ts_bias_set(tsdev->asr, XBIAS);
- if (err)
- goto ipc_error;
-
- msleep(WAIT_ADC_COMPLETION);
-
- /* read y+ and y- channels */
- err = mrstouch_ts_chan_read(tsdev->asr, MRST_TS_CHAN12, &yp, &ym);
- if (err)
- goto ipc_error;
-
- /* configure z bias for x and y channels */
- err = mrstouch_ts_bias_set(tsdev->asr, ZBIAS);
- if (err)
- goto ipc_error;
-
- msleep(WAIT_ADC_COMPLETION);
-
- /* read z+ and z- channels */
- err = mrstouch_ts_chan_read(tsdev->asr, MRST_TS_CHAN10, &zp, &zm);
- if (err)
- goto ipc_error;
-
-#if defined(MRSTOUCH_PRINT_XYZP)
- printk(KERN_INFO "X+: %d, Y+: %d, Z+: %d\n", xp, yp, zp);
-#endif
-
-#if defined(MRSTOUCH_PRINT_XYZM)
- printk(KERN_INFO "X-: %d, Y-: %d, Z-: %d\n", xm, ym, zm);
-#endif
-
- mrstouch_report_xy(tsdev, xp, yp, zp); /* report x and y to eventX */
-
- return zp;
-
-ipc_error:
- dev_err(&tsdev->spi->dev, "ipc error during adc read\n");
- return err;
-}
-
-/* PENDET interrupt handler function for NEC and MAXIM */
-static void pmic12_pendet(void *data)
-{
- unsigned int touched;
- struct mrstouch_dev *tsdev = (struct mrstouch_dev *)data;
-
- /* read touch screen channels till pen removed */
- do {
- touched = mrstouch_adc_read(tsdev);
- } while (touched > TOUCH_PRESSURE);
-}
-
-/* Handler to process PENDET interrupt */
-int mrstouch_pendet(void *data)
-{
- struct mrstouch_dev *tsdev = (struct mrstouch_dev *)data;
- while (1) {
- /* Wait for PENDET interrupt */
- if (mutex_lock_interruptible(&tsdev->lock)) {
- msleep(WAIT_ADC_COMPLETION);
- continue;
- }
-
- if (tsdev->busy)
- return 0;
-
- tsdev->busy = true;
-
- if (tsdev->vendor == PMIC_VENDOR_NEC ||
- tsdev->vendor == PMIC_VENDOR_MAXIM) {
- /* PENDET must be disabled in NEC before reading ADC */
- pendet_enable(tsdev,false); /* Disbale PENDET */
- pmic12_pendet(tsdev);
- pendet_enable(tsdev, true); /*Enable PENDET */
- } else if (tsdev->vendor == PMIC_VENDOR_FS) {
- pendet_umask(); /* Stop ADC */
- pmic0_pendet(tsdev);
- pendet_mask(); /* Stop ADC */
- } else
- dev_err(&tsdev->spi->dev, "Unsupported touchscreen: %d\n",
- tsdev->vendor);
-
- tsdev->busy = false;
-
- }
- return 0;
-}
-
-/* PENDET interrupt handler */
-static irqreturn_t pendet_intr_handler(int irq, void *handle)
-{
- struct mrstouch_dev *tsdev = (struct mrstouch_dev *)handle;
-
- mutex_unlock(&tsdev->lock);
- return IRQ_HANDLED;
-}
-
-/* Intializes input device and registers with input subsystem */
-static int ts_input_dev_init(struct mrstouch_dev *tsdev, struct spi_device *spi)
-{
- int err = 0;
-
- mrstouch_debug("%s", __func__);
-
- tsdev->input = input_allocate_device();
- if (!tsdev->input) {
- dev_err(&tsdev->spi->dev, "Unable to allocate input device.\n");
- return -EINVAL;
- }
-
- tsdev->input->name = "mrst_touchscreen";
- snprintf(tsdev->phys, sizeof(tsdev->phys),
- "%s/input0", dev_name(&spi->dev));
- tsdev->input->phys = tsdev->phys;
- tsdev->input->dev.parent = &spi->dev;
-
- tsdev->input->id.vendor = tsdev->vendor;
- tsdev->input->id.version = tsdev->rev;
-
- tsdev->input->evbit[0] = BIT_MASK(EV_KEY) | BIT_MASK(EV_ABS);
- tsdev->input->keybit[BIT_WORD(BTN_TOUCH)] = BIT_MASK(BTN_TOUCH);
-
- input_set_abs_params(tsdev->input, ABS_X, MIN_X, MIN_Y, 0, 0);
- input_set_abs_params(tsdev->input, ABS_Y, MIN_X, MIN_Y, 0, 0);
-
- err = input_register_device(tsdev->input);
- if (err) {
- dev_err(&tsdev->spi->dev, "unable to register input device\n");
- input_free_device(tsdev->input);
- return err;
- }
-
- mrstouch_debug("%s", "mrstouch initialized");
-
- return 0;
-
-}
-
-/* Probe function for touch screen driver */
-static int __devinit mrstouch_probe(struct spi_device *mrstouch_spi)
-{
- int err;
- unsigned int myirq;
- struct mrstouch_dev *tsdev;
-
- mrstouch_debug("%s(%p)", __func__, mrstouch_spi);
-
- mrstouchdevp = NULL;
- myirq = mrstouch_spi->irq;
-
- if (!mrstouch_spi->irq) {
- dev_err(&mrstouch_spi->dev, "no interrupt assigned\n");
- return -EINVAL;
- }
-
- tsdev = kzalloc(sizeof(struct mrstouch_dev), GFP_KERNEL);
- if (!tsdev) {
- dev_err(&mrstouch_spi->dev, "unable to allocate memory\n");
- return -ENOMEM;
- }
-
- tsdev->irq = myirq;
- mrstouchdevp = tsdev;
-
- err = mrstouch_adc_init(tsdev);
- if (err) {
- dev_err(&mrstouch_spi->dev, "ADC init failed\n");
- goto mrstouch_err_free_mem;
- }
-
- dev_set_drvdata(&mrstouch_spi->dev, tsdev);
- tsdev->spi = mrstouch_spi;
-
- err = ts_input_dev_init(tsdev, mrstouch_spi);
- if (err) {
- dev_err(&tsdev->spi->dev, "ts_input_dev_init failed");
- goto mrstouch_err_free_mem;
- }
-
- mutex_init(&tsdev->lock);
- mutex_lock(&tsdev->lock)
-
- mrstouch_debug("Requesting IRQ-%d", myirq);
- err = request_irq(myirq, pendet_intr_handler,
- 0, "mrstouch", tsdev);
- if (err) {
- dev_err(&tsdev->spi->dev, "unable to allocate irq\n");
- goto mrstouch_err_free_mem;
- }
-
- tsdev->pendet_thrd = kthread_run(mrstouch_pendet,
- (void *)tsdev, "pendet handler");
- if (IS_ERR(tsdev->pendet_thrd)) {
- dev_err(&tsdev->spi->dev, "kthread_run failed\n");
- err = PTR_ERR(tsdev->pendet_thrd);
- goto mrstouch_err_free_mem;
- }
- mrstouch_debug("%s", "Driver initialized");
- return 0;
-
-mrstouch_err_free_mem:
- kfree(tsdev);
- return err;
-}
-
-static int mrstouch_suspend(struct spi_device *spi, pm_message_t msg)
-{
- mrstouch_debug("%s", __func__);
- mrstouchdevp->suspended = 1;
- return 0;
-}
-
-static int mrstouch_resume(struct spi_device *spi)
-{
- mrstouch_debug("%s", __func__);
- mrstouchdevp->suspended = 0;
- return 0;
-}
-
-static int mrstouch_remove(struct spi_device *spi)
-{
- mrstouch_debug("%s", __func__);
- free_irq(mrstouchdevp->irq, mrstouchdevp);
- input_unregister_device(mrstouchdevp->input);
- input_free_device(mrstouchdevp->input);
- if (mrstouchdevp->pendet_thrd)
- kthread_stop(mrstouchdevp->pendet_thrd);
- kfree(mrstouchdevp);
- return 0;
-}
-
-static struct spi_driver mrstouch_driver = {
- .driver = {
- .name = "pmic_touch",
- .bus = &spi_bus_type,
- .owner = THIS_MODULE,
- },
- .probe = mrstouch_probe,
- .suspend = mrstouch_suspend,
- .resume = mrstouch_resume,
- .remove = mrstouch_remove,
-};
-
-static int __init mrstouch_module_init(void)
-{
- int err;
-
- mrstouch_debug("%s", __func__);
- err = spi_register_driver(&mrstouch_driver);
- if (err) {
- mrstouch_debug("%s(%d)", "SPI PENDET failed", err);
- return -1;
- }
-
- return 0;
-}
-
-static void __exit mrstouch_module_exit(void)
-{
- mrstouch_debug("%s", __func__);
- spi_unregister_driver(&mrstouch_driver);
- return;
-}
-
-module_init(mrstouch_module_init);
-module_exit(mrstouch_module_exit);
-
-MODULE_AUTHOR("Sreedhara Murthy. D.S, sreedhara.ds@intel.com");
-MODULE_DESCRIPTION("Intel Moorestown Resistive Touch Screen Driver");
-MODULE_LICENSE("GPL");
#define to_gameport_port(d) container_of(d, struct gameport, dev)
struct gameport_driver {
-
- void *private;
- char *description;
+ const char *description;
int (*connect)(struct gameport *, struct gameport_driver *drv);
int (*reconnect)(struct gameport *);
* Protocol version.
*/
-#define EV_VERSION 0x010000
+#define EV_VERSION 0x010001
/*
* IOCTLs (0x00 - 0x7f)
__s32 resolution;
};
+/**
+ * struct input_keymap_entry - used by EVIOCGKEYCODE/EVIOCSKEYCODE ioctls
+ * @scancode: scancode represented in machine-endian form.
+ * @len: length of the scancode that resides in @scancode buffer.
+ * @index: index in the keymap, may be used instead of scancode
+ * @flags: allows to specify how kernel should handle the request. For
+ * example, setting INPUT_KEYMAP_BY_INDEX flag indicates that kernel
+ * should perform lookup in keymap by @index instead of @scancode
+ * @keycode: key code assigned to this scancode
+ *
+ * The structure is used to retrieve and modify keymap data. Users have
+ * option of performing lookup either by @scancode itself or by @index
+ * in keymap entry. EVIOCGKEYCODE will also return scancode or index
+ * (depending on which element was used to perform lookup).
+ */
+struct input_keymap_entry {
+#define INPUT_KEYMAP_BY_INDEX (1 << 0)
+ __u8 flags;
+ __u8 len;
+ __u16 index;
+ __u32 keycode;
+ __u8 scancode[32];
+};
+
#define EVIOCGVERSION _IOR('E', 0x01, int) /* get driver version */
#define EVIOCGID _IOR('E', 0x02, struct input_id) /* get device ID */
#define EVIOCGREP _IOR('E', 0x03, unsigned int[2]) /* get repeat settings */
#define EVIOCSREP _IOW('E', 0x03, unsigned int[2]) /* set repeat settings */
-#define EVIOCGKEYCODE _IOR('E', 0x04, unsigned int[2]) /* get keycode */
-#define EVIOCSKEYCODE _IOW('E', 0x04, unsigned int[2]) /* set keycode */
+
+#define EVIOCGKEYCODE _IOR('E', 0x04, struct input_keymap_entry) /* get keycode */
+#define EVIOCSKEYCODE _IOW('E', 0x04, struct input_keymap_entry) /* set keycode */
#define EVIOCGNAME(len) _IOC(_IOC_READ, 'E', 0x06, len) /* get device name */
#define EVIOCGPHYS(len) _IOC(_IOC_READ, 'E', 0x07, len) /* get physical location */
#define EVIOCGUNIQ(len) _IOC(_IOC_READ, 'E', 0x08, len) /* get unique identifier */
-#define EVIOCGKEY(len) _IOC(_IOC_READ, 'E', 0x18, len) /* get global keystate */
+#define EVIOCGKEY(len) _IOC(_IOC_READ, 'E', 0x18, len) /* get global key state */
#define EVIOCGLED(len) _IOC(_IOC_READ, 'E', 0x19, len) /* get all LEDs */
#define EVIOCGSND(len) _IOC(_IOC_READ, 'E', 0x1a, len) /* get all sounds status */
#define EVIOCGSW(len) _IOC(_IOC_READ, 'E', 0x1b, len) /* get all switch states */
#define EVIOCGBIT(ev,len) _IOC(_IOC_READ, 'E', 0x20 + ev, len) /* get event bits */
-#define EVIOCGABS(abs) _IOR('E', 0x40 + abs, struct input_absinfo) /* get abs value/limits */
-#define EVIOCSABS(abs) _IOW('E', 0xc0 + abs, struct input_absinfo) /* set abs value/limits */
+#define EVIOCGABS(abs) _IOR('E', 0x40 + abs, struct input_absinfo) /* get abs value/limits */
+#define EVIOCSABS(abs) _IOW('E', 0xc0 + abs, struct input_absinfo) /* set abs value/limits */
#define EVIOCSFF _IOC(_IOC_WRITE, 'E', 0x80, sizeof(struct ff_effect)) /* send a force effect to a force feedback device */
#define EVIOCRMFF _IOW('E', 0x81, int) /* Erase a force effect */
* @keycodemax: size of keycode table
* @keycodesize: size of elements in keycode table
* @keycode: map of scancodes to keycodes for this device
+ * @getkeycode: optional legacy method to retrieve current keymap.
* @setkeycode: optional method to alter current keymap, used to implement
* sparse keymaps. If not supplied default mechanism will be used.
* The method is being called while holding event_lock and thus must
* not sleep
- * @getkeycode: optional method to retrieve current keymap. If not supplied
- * default mechanism will be used. The method is being called while
- * holding event_lock and thus must not sleep
+ * @getkeycode_new: transition method
+ * @setkeycode_new: transition method
* @ff: force feedback structure associated with the device if device
* supports force feedback effects
* @repeat_key: stores key code of the last key pressed; used to implement
unsigned int keycodemax;
unsigned int keycodesize;
void *keycode;
+
int (*setkeycode)(struct input_dev *dev,
unsigned int scancode, unsigned int keycode);
int (*getkeycode)(struct input_dev *dev,
unsigned int scancode, unsigned int *keycode);
+ int (*setkeycode_new)(struct input_dev *dev,
+ const struct input_keymap_entry *ke,
+ unsigned int *old_keycode);
+ int (*getkeycode_new)(struct input_dev *dev,
+ struct input_keymap_entry *ke);
struct ff_device *ff;
INPUT_GENERATE_ABS_ACCESSORS(flat, flat)
INPUT_GENERATE_ABS_ACCESSORS(res, resolution)
-int input_get_keycode(struct input_dev *dev,
- unsigned int scancode, unsigned int *keycode);
+int input_scancode_to_scalar(const struct input_keymap_entry *ke,
+ unsigned int *scancode);
+
+int input_get_keycode(struct input_dev *dev, struct input_keymap_entry *ke);
int input_set_keycode(struct input_dev *dev,
- unsigned int scancode, unsigned int keycode);
+ const struct input_keymap_entry *ke);
extern struct class input_class;
--- /dev/null
+/*
+ * Copyright (C) ST-Ericsson SA 2010
+ * Author: Naveen Kumar G <naveen.gaddipati@stericsson.com> for ST-Ericsson
+ * License terms:GNU General Public License (GPL) version 2
+ */
+
+#ifndef _BU21013_H
+#define _BU21013_H
+
+/**
+ * struct bu21013_platform_device - Handle the platform data
+ * @cs_en: pointer to the cs enable function
+ * @cs_dis: pointer to the cs disable function
+ * @irq_read_val: pointer to read the pen irq value function
+ * @x_max_res: xmax resolution
+ * @y_max_res: ymax resolution
+ * @touch_x_max: touch x max
+ * @touch_y_max: touch y max
+ * @cs_pin: chip select pin
+ * @irq: irq pin
+ * @ext_clk: external clock flag
+ * @x_flip: x flip flag
+ * @y_flip: y flip flag
+ * @wakeup: wakeup flag
+ *
+ * This is used to handle the platform data
+ */
+struct bu21013_platform_device {
+ int (*cs_en)(int reset_pin);
+ int (*cs_dis)(int reset_pin);
+ int (*irq_read_val)(void);
+ int x_max_res;
+ int y_max_res;
+ int touch_x_max;
+ int touch_y_max;
+ unsigned int cs_pin;
+ unsigned int irq;
+ bool ext_clk;
+ bool x_flip;
+ bool y_flip;
+ bool wakeup;
+};
+
+#endif
int (*start)(struct serio *);
void (*stop)(struct serio *);
- struct serio *parent, *child;
+ struct serio *parent;
+ struct list_head child_node; /* Entry in parent->children list */
+ struct list_head children;
unsigned int depth; /* level of nesting in serio hierarchy */
struct serio_driver *drv; /* accessed from interrupt, must be protected by serio->lock and serio->sem */
#define to_serio_port(d) container_of(d, struct serio, dev)
struct serio_driver {
- void *private;
- char *description;
+ const char *description;
- struct serio_device_id *id_table;
+ const struct serio_device_id *id_table;
bool manual_bind;
void (*write_wakeup)(struct serio *);
#define SERIO_W8001 0x39
#define SERIO_DYNAPRO 0x3a
#define SERIO_HAMPSHIRE 0x3b
+#define SERIO_PS2MULT 0x3c
#endif
unsigned int len; /* Used number of entries */
unsigned int alloc; /* Size of *scan in bytes */
u64 ir_type;
- char *name;
+ const char *name;
spinlock_t lock;
};
git.openpandora.org / pandora-kernel.git / commitdiff