+++ /dev/null
-/*
- * pata_it8172.c - IT8172 PATA for new ATA layer
- * (C) 2005 Red Hat Inc
- * Alan Cox <alan@redhat.com>
- *
- * Based heavily on
- *
- * BRIEF MODULE DESCRIPTION
- * IT8172 IDE controller support
- *
- * Copyright 2000 MontaVista Software Inc.
- * Author: MontaVista Software, Inc.
- * stevel@mvista.com or source@mvista.com
- *
- * This program is free software; you can redistribute it and/or modify it
- * under the terms of the GNU General Public License as published by the
- * Free Software Foundation; either version 2 of the License, or (at your
- * option) any later version.
- *
- * THIS SOFTWARE IS PROVIDED ``AS IS'' AND ANY EXPRESS OR IMPLIED
- * WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF
- * MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN
- * NO EVENT SHALL THE AUTHOR BE LIABLE FOR ANY DIRECT, INDIRECT,
- * INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT
- * NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF
- * USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON
- * ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
- * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF
- * THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
- *
- * You should have received a copy of the GNU General Public License along
- * with this program; if not, write to the Free Software Foundation, Inc.,
- * 675 Mass Ave, Cambridge, MA 02139, USA.
- *
- * TODO
- * Check for errata
- * See if we really need to force native mode
- * PIO timings (also lacking in original)
- */
-
-#include <linux/kernel.h>
-#include <linux/module.h>
-#include <linux/pci.h>
-#include <linux/init.h>
-#include <linux/blkdev.h>
-#include <linux/delay.h>
-#include <scsi/scsi_host.h>
-#include <linux/libata.h>
-
-#define DRV_NAME "pata_it8172"
-#define DRV_VERSION "0.3.1"
-
-static int it8172_pre_reset(struct ata_port *ap)
-{
- static const struct pci_bits it8172_enable_bits[] = {
- { 0x00, 0, 0x00, 0x00 },
- { 0x40, 1, 0x00, 0x01 }
- };
-
- struct pci_dev *pdev = to_pci_dev(ap->host->dev);
-
- if (ap->port_no && !pci_test_config_bits(pdev, &it8172_enable_bits[ap->port_no])) {
- ata_port_disable(ap);
- printk(KERN_INFO "ata%u: port disabled. ignoring.\n", ap->id);
- return 0;
- }
- ap->cbl = ATA_CBL_PATA40;
- return ata_std_prereset(ap);
-}
-
-static void it8172_error_handler(struct ata_port *ap)
-{
- ata_bmdma_drive_eh(ap, it8172_pre_reset, ata_std_softreset, NULL, ata_std_postreset);
-}
-
-/**
- * it8172_set_pio_timing - set initial PIO mode data
- * @ap: ATA interface
- * @adev: ATA device
- *
- * Called by both the pio and dma setup functions to set the controller
- * timings for PIO transfers. We must load both the mode number and
- * timing values into the controller.
- */
-
-static void it8172_set_pio_timing(struct ata_port *ap, struct ata_device *adev, int pio)
-{
- struct pci_dev *pdev = to_pci_dev(ap->host->dev);
- u16 reg40;
-
- pci_read_config_word(pdev, 0x40, ®40);
-
- /*
- * FIX! The DIOR/DIOW pulse width and recovery times in port 0x44
- * are being left at the default values of 8 PCI clocks (242 nsec
- * for a 33 MHz clock). These can be safely shortened at higher
- * PIO modes. The DIOR/DIOW pulse width and recovery times only
- * apply to PIO modes, not to the DMA modes.
- */
-
- /*
- * Enable port 0x44. The IT8172G spec is confused; it calls
- * this register the "Slave IDE Timing Register", but in fact,
- * it controls timing for both master and slave drives.
- */
-
- reg40 |= 0x4000;
- if (adev->devno) {
- reg40 &= 0xC006;
- if (pio > 1)
- /* Enable prefetch and IORDY sample-point */
- reg40 |= 0x0060;
- } else {
- reg40 &= 0xC060;
- if (pio > 1)
- /* Enable prefetch and IORDY sample-point */
- reg40 |= 0x0006;
- }
- /* Write back the enables */
- pci_write_config_word(pdev, 0x40, reg40);
-}
-
-/**
- * it8172_set_piomode - set initial PIO mode data
- * @ap: ATA interface
- * @adev: ATA device
- *
- * Called to do the PIO mode setup. We use a shared helper for this
- * as the DMA setup must also adjust the PIO timing information.
- */
-
-static void it8172_set_piomode(struct ata_port *ap, struct ata_device *adev)
-{
- it8172_set_pio_timing(ap, adev, adev->pio_mode - XFER_PIO_0);
-}
-
-/**
- * it8172_set_dmamode - set initial DMA mode data
- * @ap: ATA interface
- * @adev: ATA device
- *
- * Called to do the DMA mode setup. We must tune an appropriate PIO
- * mode to match.
- */
-
-static void it8172_set_dmamode(struct ata_port *ap, struct ata_device *adev)
-{
- struct pci_dev *pdev = to_pci_dev(ap->host->dev);
- int dn = (2 * ap->port_no) + adev->devno;
- u8 reg48, reg4a;
- int pio;
-
- static const int pio_map[] = { 1, 3, 4};
- /*
- * Setting the DMA cycle time to 2 or 3 PCI clocks (60 and 91 nsec
- * at 33 MHz PCI clock) seems to cause BadCRC errors during DMA
- * transfers on some drives, even though both numbers meet the minimum
- * ATAPI-4 spec of 73 and 54 nsec for UDMA 1 and 2 respectively.
- * So the faster times are just commented out here. The good news is
- * that the slower cycle time has very little affect on transfer
- * performance.
- */
-
- pci_read_config_byte(pdev, 0x48, ®48);
- pci_read_config_byte(pdev, 0x4A, ®4a);
-
- reg4a &= ~(3 << (4 * dn));
-
- if (adev->dma_mode >= XFER_UDMA_0) {
- reg48 |= 1 << dn;
-#ifdef UDMA_TIMING_SET
- reg4a |= ((adev->dma_mode - XFER_UDMA_0) << (4 * dn));
-#endif
- pio = 4;
- } else {
- pio = pio_map[adev->dma_mode - XFER_MW_DMA_0];
- reg48 &= ~ (1 << dn);
- }
- pci_write_config_byte(pdev, 0x48, reg48);
- pci_write_config_byte(pdev, 0x4A, reg4a);
- it8172_set_pio_timing(ap, adev, pio);
-
-}
-
-static struct scsi_host_template it8172_sht = {
- .module = THIS_MODULE,
- .name = DRV_NAME,
- .ioctl = ata_scsi_ioctl,
- .queuecommand = ata_scsi_queuecmd,
- .can_queue = ATA_DEF_QUEUE,
- .this_id = ATA_SHT_THIS_ID,
- .sg_tablesize = LIBATA_MAX_PRD,
- .max_sectors = ATA_MAX_SECTORS,
- .cmd_per_lun = ATA_SHT_CMD_PER_LUN,
- .emulated = ATA_SHT_EMULATED,
- .use_clustering = ATA_SHT_USE_CLUSTERING,
- .proc_name = DRV_NAME,
- .dma_boundary = ATA_DMA_BOUNDARY,
- .slave_configure = ata_scsi_slave_config,
- .bios_param = ata_std_bios_param,
-};
-
-static struct ata_port_operations it8172_port_ops = {
- .port_disable = ata_port_disable,
- .set_piomode = it8172_set_piomode,
- .set_dmamode = it8172_set_dmamode,
- .mode_filter = ata_pci_default_filter,
-
- .tf_load = ata_tf_load,
- .tf_read = ata_tf_read,
- .check_status = ata_check_status,
- .exec_command = ata_exec_command,
- .dev_select = ata_std_dev_select,
-
- .freeze = ata_bmdma_freeze,
- .thaw = ata_bmdma_thaw,
- .error_handler = it8172_error_handler,
- .post_internal_cmd = ata_bmdma_post_internal_cmd,
-
- .bmdma_setup = ata_bmdma_setup,
- .bmdma_start = ata_bmdma_start,
- .bmdma_stop = ata_bmdma_stop,
- .bmdma_status = ata_bmdma_status,
-
- .qc_prep = ata_qc_prep,
- .qc_issue = ata_qc_issue_prot,
- .eng_timeout = ata_eng_timeout,
- .data_xfer = ata_pio_data_xfer,
-
- .irq_handler = ata_interrupt,
- .irq_clear = ata_bmdma_irq_clear,
-
- .port_start = ata_port_start,
- .port_stop = ata_port_stop,
- .host_stop = ata_host_stop
-};
-
-static int it8172_init_one(struct pci_dev *dev, const struct pci_device_id *id)
-{
- static struct ata_port_info info = {
- .sht = &it8172_sht,
- .flags = ATA_FLAG_SLAVE_POSS | ATA_FLAG_SRST,
- .pio_mask = 0x1f,
- .mwdma_mask = 0x06, /* No MWDMA0 support */
- .udma_mask = 0x7,
- .port_ops = &it8172_port_ops
- };
- static struct ata_port_info *port_info[2] = { &info, &info };
-
- if ((!(PCI_FUNC(dev->devfn) & 1) ||
- (!((dev->class >> 8) == PCI_CLASS_STORAGE_IDE))))
- return -ENODEV; /* IT8172 is more than an IDE controller */
-
- return ata_pci_init_one(dev, port_info, 2);
-}
-
-static struct pci_device_id it8172[] = {
- { PCI_DEVICE(PCI_VENDOR_ID_ITE, PCI_DEVICE_ID_ITE_IT8172G), },
- { 0, },
-};
-
-static struct pci_driver it8172_pci_driver = {
- .name = DRV_NAME,
- .id_table = it8172,
- .probe = it8172_init_one,
- .remove = ata_pci_remove_one
-};
-
-static int __init it8172_init(void)
-{
- return pci_register_driver(&it8172_pci_driver);
-}
-
-
-static void __exit it8172_exit(void)
-{
- pci_unregister_driver(&it8172_pci_driver);
-}
-
-
-MODULE_AUTHOR("Alan Cox");
-MODULE_DESCRIPTION("low-level driver for ITE IT8172");
-MODULE_LICENSE("GPL");
-MODULE_DEVICE_TABLE(pci, it8172);
-MODULE_VERSION(DRV_VERSION);
-
-module_init(it8172_init);
-module_exit(it8172_exit);
git.openpandora.org / pandora-kernel.git / commitdiff