X-Git-Url: https://git.openpandora.org/cgi-bin/gitweb.cgi?p=pandora-kernel.git;a=blobdiff_plain;f=include%2Fnet%2Fmac80211.h;h=e24b0363e6cb20616118f4376d0199a250b15543;hp=45d7d44d7cbe401ff92050f31531c2526a774b30;hb=a69eee4988752c7196677958b4ed8f4c2b28499a;hpb=795e74f7a69f9c08afa4fa7c86cc4f18a62bd630 diff --git a/include/net/mac80211.h b/include/net/mac80211.h index 45d7d44d7cbe..e24b0363e6cb 100644 --- a/include/net/mac80211.h +++ b/include/net/mac80211.h @@ -144,6 +144,8 @@ struct ieee80211_low_level_stats { * new beacon (beaconing modes) * @BSS_CHANGED_BEACON_ENABLED: Beaconing should be * enabled/disabled (beaconing modes) + * @BSS_CHANGED_CQM: Connection quality monitor config changed + * @BSS_CHANGED_IBSS: IBSS join status changed */ enum ieee80211_bss_change { BSS_CHANGED_ASSOC = 1<<0, @@ -156,6 +158,10 @@ enum ieee80211_bss_change { BSS_CHANGED_BSSID = 1<<7, BSS_CHANGED_BEACON = 1<<8, BSS_CHANGED_BEACON_ENABLED = 1<<9, + BSS_CHANGED_CQM = 1<<10, + BSS_CHANGED_IBSS = 1<<11, + + /* when adding here, make sure to change ieee80211_reconfig */ }; /** @@ -165,6 +171,8 @@ enum ieee80211_bss_change { * to that BSS) that can change during the lifetime of the BSS. * * @assoc: association status + * @ibss_joined: indicates whether this station is part of an IBSS + * or not * @aid: association ID number, valid only when @assoc is true * @use_cts_prot: use CTS protection * @use_short_preamble: use 802.11b short preamble; @@ -183,13 +191,19 @@ enum ieee80211_bss_change { * the current band. * @bssid: The BSSID for this BSS * @enable_beacon: whether beaconing should be enabled or not + * @channel_type: Channel type for this BSS -- the hardware might be + * configured for HT40+ while this BSS only uses no-HT, for + * example. * @ht_operation_mode: HT operation mode (like in &struct ieee80211_ht_info). * This field is only valid when the channel type is one of the HT types. + * @cqm_rssi_thold: Connection quality monitor RSSI threshold, a zero value + * implies disabled + * @cqm_rssi_hyst: Connection quality monitor RSSI hysteresis */ struct ieee80211_bss_conf { const u8 *bssid; /* association related data */ - bool assoc; + bool assoc, ibss_joined; u16 aid; /* erp related data */ bool use_cts_prot; @@ -202,6 +216,9 @@ struct ieee80211_bss_conf { u64 timestamp; u32 basic_rates; u16 ht_operation_mode; + s32 cqm_rssi_thold; + u32 cqm_rssi_hyst; + enum nl80211_channel_type channel_type; }; /** @@ -267,6 +284,9 @@ struct ieee80211_bss_conf { * @IEEE80211_TX_INTFL_NL80211_FRAME_TX: Frame was requested through nl80211 * MLME command (internal to mac80211 to figure out whether to send TX * status to user space) + * @IEEE80211_TX_CTL_LDPC: tells the driver to use LDPC for this frame + * @IEEE80211_TX_CTL_STBC: Enables Space-Time Block Coding (STBC) for this + * frame and selects the maximum number of streams that it can use. */ enum mac80211_tx_control_flags { IEEE80211_TX_CTL_REQ_TX_STATUS = BIT(0), @@ -290,6 +310,9 @@ enum mac80211_tx_control_flags { IEEE80211_TX_INTFL_RETRANSMISSION = BIT(19), IEEE80211_TX_INTFL_HAS_RADIOTAP = BIT(20), IEEE80211_TX_INTFL_NL80211_FRAME_TX = BIT(21), + IEEE80211_TX_CTL_LDPC = BIT(22), + IEEE80211_TX_CTL_STBC = BIT(23) | BIT(24), +#define IEEE80211_TX_CTL_STBC_SHIFT 23 }; /** @@ -388,11 +411,11 @@ struct ieee80211_tx_rate { * @status: union for status data * @driver_data: array of driver_data pointers * @ampdu_ack_len: number of acked aggregated frames. - * relevant only if IEEE80211_TX_STATUS_AMPDU was set. + * relevant only if IEEE80211_TX_STAT_AMPDU was set. * @ampdu_ack_map: block ack bit map for the aggregation. - * relevant only if IEEE80211_TX_STATUS_AMPDU was set. + * relevant only if IEEE80211_TX_STAT_AMPDU was set. * @ampdu_len: number of aggregated frames. - * relevant only if IEEE80211_TX_STATUS_AMPDU was set. + * relevant only if IEEE80211_TX_STAT_AMPDU was set. * @ack_signal: signal strength of the ACK frame */ struct ieee80211_tx_info { @@ -543,7 +566,6 @@ enum mac80211_rx_flags { * @signal: signal strength when receiving this frame, either in dBm, in dB or * unspecified depending on the hardware capabilities flags * @IEEE80211_HW_SIGNAL_* - * @noise: noise when receiving this frame, in dBm. * @antenna: antenna used * @rate_idx: index of data rate into band's supported rates or MCS index if * HT rates are use (RX_FLAG_HT) @@ -554,7 +576,6 @@ struct ieee80211_rx_status { enum ieee80211_band band; int freq; int signal; - int noise; int antenna; int rate_idx; int flag; @@ -580,11 +601,15 @@ struct ieee80211_rx_status { * may turn the device off as much as possible. Typically, this flag will * be set when an interface is set UP but not associated or scanning, but * it can also be unset in that case when monitor interfaces are active. + * @IEEE80211_CONF_QOS: Enable 802.11e QoS also know as WMM (Wireless + * Multimedia). On some drivers (iwlwifi is one of know) we have + * to enable/disable QoS explicitly. */ enum ieee80211_conf_flags { IEEE80211_CONF_MONITOR = (1<<0), IEEE80211_CONF_PS = (1<<1), IEEE80211_CONF_IDLE = (1<<2), + IEEE80211_CONF_QOS = (1<<3), }; @@ -599,6 +624,7 @@ enum ieee80211_conf_flags { * @IEEE80211_CONF_CHANGE_RETRY_LIMITS: retry limits changed * @IEEE80211_CONF_CHANGE_IDLE: Idle flag changed * @IEEE80211_CONF_CHANGE_SMPS: Spatial multiplexing powersave mode changed + * @IEEE80211_CONF_CHANGE_QOS: Quality of service was enabled or disabled */ enum ieee80211_conf_changed { IEEE80211_CONF_CHANGE_SMPS = BIT(1), @@ -609,6 +635,7 @@ enum ieee80211_conf_changed { IEEE80211_CONF_CHANGE_CHANNEL = BIT(6), IEEE80211_CONF_CHANGE_RETRY_LIMITS = BIT(7), IEEE80211_CONF_CHANGE_IDLE = BIT(8), + IEEE80211_CONF_CHANGE_QOS = BIT(9), }; /** @@ -649,6 +676,9 @@ enum ieee80211_smps_mode { * @dynamic_ps_timeout: The dynamic powersave timeout (in ms), see the * powersave documentation below. This variable is valid only when * the CONF_PS flag is set. + * @dynamic_ps_forced_timeout: The dynamic powersave timeout (in ms) configured + * by cfg80211 (essentially, wext) If set, this value overrules the value + * chosen by mac80211 based on ps qos network latency. * * @power_level: requested transmit power (in dBm) * @@ -668,7 +698,7 @@ enum ieee80211_smps_mode { */ struct ieee80211_conf { u32 flags; - int power_level, dynamic_ps_timeout; + int power_level, dynamic_ps_timeout, dynamic_ps_forced_timeout; int max_sleep_period; u16 listen_interval; @@ -681,6 +711,28 @@ struct ieee80211_conf { enum ieee80211_smps_mode smps_mode; }; +/** + * struct ieee80211_channel_switch - holds the channel switch data + * + * The information provided in this structure is required for channel switch + * operation. + * + * @timestamp: value in microseconds of the 64-bit Time Synchronization + * Function (TSF) timer when the frame containing the channel switch + * announcement was received. This is simply the rx.mactime parameter + * the driver passed into mac80211. + * @block_tx: Indicates whether transmission must be blocked before the + * scheduled channel switch, as indicated by the AP. + * @channel: the new channel to switch to + * @count: the number of TBTT's until the channel switch event + */ +struct ieee80211_channel_switch { + u64 timestamp; + bool block_tx; + struct ieee80211_channel *channel; + u8 count; +}; + /** * struct ieee80211_vif - per-interface data * @@ -907,10 +959,6 @@ enum ieee80211_tkip_key_type { * one milliwatt. This is the preferred method since it is standardized * between different devices. @max_signal does not need to be set. * - * @IEEE80211_HW_NOISE_DBM: - * Hardware can provide noise (radio interference) values in units dBm, - * decibel difference from one milliwatt. - * * @IEEE80211_HW_SPECTRUM_MGMT: * Hardware supports spectrum management defined in 802.11h * Measurement, Channel Switch, Quieting, TPC @@ -954,6 +1002,17 @@ enum ieee80211_tkip_key_type { * Hardware can provide ack status reports of Tx frames to * the stack. * + * @IEEE80211_HW_CONNECTION_MONITOR: + * The hardware performs its own connection monitoring, including + * periodic keep-alives to the AP and probing the AP on beacon loss. + * When this flag is set, signaling beacon-loss will cause an immediate + * change to disassociated state. + * + * @IEEE80211_HW_SUPPORTS_CQM_RSSI: + * Hardware can do connection quality monitoring - i.e. it can monitor + * connection quality related parameters, such as the RSSI level and + * provide notifications if configured trigger levels are reached. + * */ enum ieee80211_hw_flags { IEEE80211_HW_HAS_RATE_CONTROL = 1<<0, @@ -963,7 +1022,7 @@ enum ieee80211_hw_flags { IEEE80211_HW_2GHZ_SHORT_PREAMBLE_INCAPABLE = 1<<4, IEEE80211_HW_SIGNAL_UNSPEC = 1<<5, IEEE80211_HW_SIGNAL_DBM = 1<<6, - IEEE80211_HW_NOISE_DBM = 1<<7, + /* use this hole */ IEEE80211_HW_SPECTRUM_MGMT = 1<<8, IEEE80211_HW_AMPDU_AGGREGATION = 1<<9, IEEE80211_HW_SUPPORTS_PS = 1<<10, @@ -975,6 +1034,8 @@ enum ieee80211_hw_flags { IEEE80211_HW_SUPPORTS_DYNAMIC_SMPS = 1<<16, IEEE80211_HW_SUPPORTS_UAPSD = 1<<17, IEEE80211_HW_REPORTS_TX_ACK_STATUS = 1<<18, + IEEE80211_HW_CONNECTION_MONITOR = 1<<19, + IEEE80211_HW_SUPPORTS_CQM_RSSI = 1<<20, }; /** @@ -1591,6 +1652,11 @@ enum ieee80211_ampdu_mlme_action { * @flush: Flush all pending frames from the hardware queue, making sure * that the hardware queues are empty. If the parameter @drop is set * to %true, pending frames may be dropped. The callback can sleep. + * + * @channel_switch: Drivers that need (or want) to offload the channel + * switch operation for CSAs received from the AP may implement this + * callback. They must then call ieee80211_chswitch_done() to indicate + * completion of the channel switch. */ struct ieee80211_ops { int (*tx)(struct ieee80211_hw *hw, struct sk_buff *skb); @@ -1606,7 +1672,7 @@ struct ieee80211_ops { struct ieee80211_bss_conf *info, u32 changed); u64 (*prepare_multicast)(struct ieee80211_hw *hw, - int mc_count, struct dev_addr_list *mc_list); + struct netdev_hw_addr_list *mc_list); void (*configure_filter)(struct ieee80211_hw *hw, unsigned int changed_flags, unsigned int *total_flags, @@ -1621,7 +1687,7 @@ struct ieee80211_ops { struct ieee80211_key_conf *conf, struct ieee80211_sta *sta, u32 iv32, u16 *phase1key); - int (*hw_scan)(struct ieee80211_hw *hw, + int (*hw_scan)(struct ieee80211_hw *hw, struct ieee80211_vif *vif, struct cfg80211_scan_request *req); void (*sw_scan_start)(struct ieee80211_hw *hw); void (*sw_scan_complete)(struct ieee80211_hw *hw); @@ -1646,13 +1712,16 @@ struct ieee80211_ops { struct ieee80211_vif *vif, enum ieee80211_ampdu_mlme_action action, struct ieee80211_sta *sta, u16 tid, u16 *ssn); - + int (*get_survey)(struct ieee80211_hw *hw, int idx, + struct survey_info *survey); void (*rfkill_poll)(struct ieee80211_hw *hw); void (*set_coverage_class)(struct ieee80211_hw *hw, u8 coverage_class); #ifdef CONFIG_NL80211_TESTMODE int (*testmode_cmd)(struct ieee80211_hw *hw, void *data, int len); #endif void (*flush)(struct ieee80211_hw *hw, bool drop); + void (*channel_switch)(struct ieee80211_hw *hw, + struct ieee80211_channel_switch *ch_switch); }; /** @@ -1802,7 +1871,10 @@ void ieee80211_restart_hw(struct ieee80211_hw *hw); * ieee80211_rx - receive frame * * Use this function to hand received frames to mac80211. The receive - * buffer in @skb must start with an IEEE 802.11 header. + * buffer in @skb must start with an IEEE 802.11 header. In case of a + * paged @skb is used, the driver is recommended to put the ieee80211 + * header of the frame on the linear part of the @skb to avoid memory + * allocation and/or memcpy by the stack. * * This function may not be called in IRQ context. Calls to this function * for a single hardware must be synchronized against each other. Calls to @@ -2364,12 +2436,52 @@ void ieee80211_sta_block_awake(struct ieee80211_hw *hw, * * @vif: &struct ieee80211_vif pointer from the add_interface callback. * - * When beacon filtering is enabled with IEEE80211_HW_BEACON_FILTERING and - * IEEE80211_CONF_PS is set, the driver needs to inform whenever the + * When beacon filtering is enabled with %IEEE80211_HW_BEACON_FILTERING and + * %IEEE80211_CONF_PS is set, the driver needs to inform whenever the * hardware is not receiving beacons with this function. */ void ieee80211_beacon_loss(struct ieee80211_vif *vif); +/** + * ieee80211_connection_loss - inform hardware has lost connection to the AP + * + * @vif: &struct ieee80211_vif pointer from the add_interface callback. + * + * When beacon filtering is enabled with %IEEE80211_HW_BEACON_FILTERING, and + * %IEEE80211_CONF_PS and %IEEE80211_HW_CONNECTION_MONITOR are set, the driver + * needs to inform if the connection to the AP has been lost. + * + * This function will cause immediate change to disassociated state, + * without connection recovery attempts. + */ +void ieee80211_connection_loss(struct ieee80211_vif *vif); + +/** + * ieee80211_cqm_rssi_notify - inform a configured connection quality monitoring + * rssi threshold triggered + * + * @vif: &struct ieee80211_vif pointer from the add_interface callback. + * @rssi_event: the RSSI trigger event type + * @gfp: context flags + * + * When the %IEEE80211_HW_SUPPORTS_CQM_RSSI is set, and a connection quality + * monitoring is configured with an rssi threshold, the driver will inform + * whenever the rssi level reaches the threshold. + */ +void ieee80211_cqm_rssi_notify(struct ieee80211_vif *vif, + enum nl80211_cqm_rssi_threshold_event rssi_event, + gfp_t gfp); + +/** + * ieee80211_chswitch_done - Complete channel switch process + * @vif: &struct ieee80211_vif pointer from the add_interface callback. + * @success: make the channel switch successful or not + * + * Complete the channel switch post-process: set the new operational channel + * and wake up the suspended queues. + */ +void ieee80211_chswitch_done(struct ieee80211_vif *vif, bool success); + /* Rate control API */ /**