X-Git-Url: https://git.openpandora.org/cgi-bin/gitweb.cgi?p=pandora-kernel.git;a=blobdiff_plain;f=arch%2Farm%2Fmach-omap2%2Fboard-apollon.c;h=878ff9181d0e5159477f5560e571da9cedecf91d;hp=6c6ba172cdf6d7592da3fe42a2b73d0f0e12b514;hb=b06b5a53adcc3ace1a82b324edf2b0c37e7be00e;hpb=e44e20ff1273cf96c7f195297208f654c49295cf

diff --git a/arch/arm/mach-omap2/board-apollon.c b/arch/arm/mach-omap2/board-apollon.c
index 6c6ba172cdf6..878ff9181d0e 100644
--- a/arch/arm/mach-omap2/board-apollon.c
+++ b/arch/arm/mach-omap2/board-apollon.c
@@ -1,5 +1,5 @@
 /*
- * linux/arch/arm/mach-omap/omap2/board-apollon.c
+ * linux/arch/arm/mach-omap2/board-apollon.c
  *
  * Copyright (C) 2005,2006 Samsung Electronics
  * Author: Kyungmin Park <kyungmin.park@samsung.com>
@@ -22,6 +22,7 @@
 #include <linux/mtd/mtd.h>
 #include <linux/mtd/partitions.h>
 #include <linux/mtd/onenand.h>
+#include <linux/irq.h>
 #include <linux/interrupt.h>
 #include <linux/delay.h>
 
@@ -166,8 +167,8 @@ static struct omap_uart_config apollon_uart_config __initdata = {
 
 static struct omap_mmc_config apollon_mmc_config __initdata = {
 	.mmc [0] = {
-		.enabled 	= 0,
-		.wire4		= 0,
+		.enabled 	= 1,
+		.wire4		= 1,
 		.wp_pin		= -1,
 		.power_pin	= -1,
 		.switch_pin	= -1,
@@ -203,7 +204,7 @@ static void __init apollon_led_init(void)
 	omap_set_gpio_dataout(LED2_GPIO15, 0);
 }
 
-static irqreturn_t apollon_sw_interrupt(int irq, void *ignored, struct pt_regs *regs)
+static irqreturn_t apollon_sw_interrupt(int irq, void *ignored)
 {
 	static unsigned int led0, led1, led2;
 
@@ -234,17 +235,17 @@ static void __init apollon_sw_init(void)
 
 	set_irq_type(OMAP_GPIO_IRQ(SW_ENTER_GPIO16), IRQT_RISING);
 	if (request_irq(OMAP_GPIO_IRQ(SW_ENTER_GPIO16), &apollon_sw_interrupt,
-				SA_SHIRQ, "enter sw",
+				IRQF_SHARED, "enter sw",
 				&apollon_sw_interrupt))
 		return;
 	set_irq_type(OMAP_GPIO_IRQ(SW_UP_GPIO17), IRQT_RISING);
 	if (request_irq(OMAP_GPIO_IRQ(SW_UP_GPIO17), &apollon_sw_interrupt,
-				SA_SHIRQ, "up sw",
+				IRQF_SHARED, "up sw",
 				&apollon_sw_interrupt))
 		return;
 	set_irq_type(OMAP_GPIO_IRQ(SW_DOWN_GPIO58), IRQT_RISING);
 	if (request_irq(OMAP_GPIO_IRQ(SW_DOWN_GPIO58), &apollon_sw_interrupt,
-				SA_SHIRQ, "down sw",
+				IRQF_SHARED, "down sw",
 				&apollon_sw_interrupt))
 		return;
 }
@@ -257,6 +258,9 @@ static void __init omap_apollon_init(void)
 	/* REVISIT: where's the correct place */
 	omap_cfg_reg(W19_24XX_SYS_NIRQ);
 
+	/* Use Interal loop-back in MMC/SDIO Module Input Clock selection */
+	CONTROL_DEVCONF |= (1 << 24);
+
 	/*
  	 * Make sure the serial ports are muxed on at this point.
 	 * You have to mux them off in device drivers later on