X-Git-Url: https://git.openpandora.org/cgi-bin/gitweb.cgi?p=pandora-kernel.git;a=blobdiff_plain;f=Documentation%2Fkernel-parameters.txt;h=f0001eb3317307d211e46f097621f49afe82d6a3;hp=a0c5c5f4fce6e9587346a4a049c9725e5ca45de5;hb=1c5b4c2b70b1c388e34874b2a3acda64f46bbc9a;hpb=c1f4246716392ec8693c23cffb969bd73c1b0910

diff --git a/Documentation/kernel-parameters.txt b/Documentation/kernel-parameters.txt
index a0c5c5f4fce6..f0001eb33173 100644
--- a/Documentation/kernel-parameters.txt
+++ b/Documentation/kernel-parameters.txt
@@ -315,12 +315,12 @@ bytes respectively. Such letter suffixes can also be entirely omitted.
 			CPU-intensive style benchmark, and it can vary highly in
 			a microbenchmark depending on workload and compiler.
 
-			1: only for 32-bit processes
-			2: only for 64-bit processes
+			32: only for 32-bit processes
+			64: only for 64-bit processes
 			on: enable for both 32- and 64-bit processes
 			off: disable for both 32- and 64-bit processes
 
-	amd_iommu=	[HW,X86-84]
+	amd_iommu=	[HW,X86-64]
 			Pass parameters to the AMD IOMMU driver in the system.
 			Possible values are:
 			fullflush - enable flushing of IO/TLB entries when
@@ -552,6 +552,8 @@ bytes respectively. Such letter suffixes can also be entirely omitted.
 			UART at the specified I/O port or MMIO address,
 			switching to the matching ttyS device later.  The
 			options are the same as for ttyS, above.
+		hvc<n>	Use the hypervisor console device <n>. This is for
+			both Xen and PowerPC hypervisors.
 
                 If the device connected to the port is not a TTY but a braille
                 device, prepend "brl," before the device type, for instance
@@ -703,6 +705,7 @@ bytes respectively. Such letter suffixes can also be entirely omitted.
 
 	earlyprintk=	[X86,SH,BLACKFIN]
 			earlyprintk=vga
+			earlyprintk=xen
 			earlyprintk=serial[,ttySn[,baudrate]]
 			earlyprintk=ttySn[,baudrate]
 			earlyprintk=dbgp[debugController#]
@@ -720,6 +723,8 @@ bytes respectively. Such letter suffixes can also be entirely omitted.
 			The VGA output is eventually overwritten by the real
 			console.
 
+			The xen output can only be used by Xen PV guests.
+
 	ekgdboc=	[X86,KGDB] Allow early kernel console debugging
 			ekgdboc=kbd
 
@@ -729,6 +734,12 @@ bytes respectively. Such letter suffixes can also be entirely omitted.
 	edd=		[EDD]
 			Format: {"off" | "on" | "skip[mbr]"}
 
+	efi_no_storage_paranoia [EFI; X86]
+			Using this parameter you can use more than 50% of
+			your efi variable storage. Use this parameter only if
+			you are really sure that your UEFI does sane gc and
+			fulfills the spec otherwise your board may brick.
+
 	eisa_irq_edge=	[PARISC,HW]
 			See header of drivers/parisc/eisa.c.
 
@@ -929,6 +940,7 @@ bytes respectively. Such letter suffixes can also be entirely omitted.
 	i8042.notimeout	[HW] Ignore timeout condition signalled by conroller
 	i8042.reset	[HW] Reset the controller during init and cleanup
 	i8042.unlock	[HW] Unlock (ignore) the keylock
+	i8042.kbdreset  [HW] Reset device connected to KBD port
 
 	i810=		[HW,DRM]
 
@@ -943,6 +955,20 @@ bytes respectively. Such letter suffixes can also be entirely omitted.
 	i8k.restricted	[HW] Allow controlling fans only if SYS_ADMIN
 			capability is set.
 
+	i915.invert_brightness=
+			[DRM] Invert the sense of the variable that is used to
+			set the brightness of the panel backlight. Normally a
+			brightness value of 0 indicates backlight switched off,
+			and the maximum of the brightness value sets the backlight
+			to maximum brightness. If this parameter is set to 0
+			(default) and the machine requires it, or this parameter
+			is set to 1, a brightness value of 0 sets the backlight
+			to maximum brightness, and the maximum of the brightness
+			value switches the backlight off.
+			-1 -- never invert brightness
+			 0 -- machine default
+			 1 -- force brightness inversion
+
 	icn=		[HW,ISDN]
 			Format: <io>[,<membase>[,<icn_id>[,<icn_id2>]]]
 
@@ -1280,6 +1306,8 @@ bytes respectively. Such letter suffixes can also be entirely omitted.
 
 			* dump_id: dump IDENTIFY data.
 
+			* disable: Disable this device.
+
 			If there are multiple matching configurations changing
 			the same attribute, the last one is used.