#define DRIVER_AUTHOR "Sarah Sharp"
#define DRIVER_DESC "'eXtensible' Host Controller (xHC) Driver"
+#define PORT_WAKE_BITS (PORT_WKOC_E | PORT_WKDISC_E | PORT_WKCONN_E)
+
/* Some 0.95 hardware can't handle the chain bit on a Link TRB being cleared */
static int link_quirk;
module_param(link_quirk, int, S_IRUGO | S_IWUSR);
"waited %u microseconds.\n",
XHCI_MAX_HALT_USEC);
if (!ret)
- xhci->xhc_state &= ~XHCI_STATE_HALTED;
+ xhci->xhc_state &= ~(XHCI_STATE_HALTED | XHCI_STATE_DYING);
+
return ret;
}
command |= CMD_RESET;
xhci_writel(xhci, command, &xhci->op_regs->command);
+ /* Existing Intel xHCI controllers require a delay of 1 mS,
+ * after setting the CMD_RESET bit, and before accessing any
+ * HC registers. This allows the HC to complete the
+ * reset operation and be ready for HC register access.
+ * Without this delay, the subsequent HC register access,
+ * may result in a system hang very rarely.
+ */
+ if (xhci->quirks & XHCI_INTEL_HOST)
+ udelay(1000);
+
ret = handshake(xhci, &xhci->op_regs->command,
CMD_RESET, 0, 10 * 1000 * 1000);
if (ret)
ret = pci_enable_msi(pdev);
if (ret) {
- xhci_err(xhci, "failed to allocate MSI entry\n");
+ xhci_dbg(xhci, "failed to allocate MSI entry\n");
return ret;
}
ret = request_irq(pdev->irq, (irq_handler_t)xhci_msi_irq,
0, "xhci_hcd", xhci_to_hcd(xhci));
if (ret) {
- xhci_err(xhci, "disable MSI interrupt\n");
+ xhci_dbg(xhci, "disable MSI interrupt\n");
pci_disable_msi(pdev);
}
ret = pci_enable_msix(pdev, xhci->msix_entries, xhci->msix_count);
if (ret) {
- xhci_err(xhci, "Failed to enable MSI-X\n");
+ xhci_dbg(xhci, "Failed to enable MSI-X\n");
goto free_entries;
}
return ret;
disable_msix:
- xhci_err(xhci, "disable MSI-X interrupt\n");
+ xhci_dbg(xhci, "disable MSI-X interrupt\n");
xhci_free_irq(xhci);
pci_disable_msix(pdev);
free_entries:
* generate interrupts. Don't even try to enable MSI.
*/
if (xhci->quirks & XHCI_BROKEN_MSI)
- return 0;
+ goto legacy_irq;
/* unregister the legacy interrupt */
if (hcd->irq)
return -EINVAL;
}
+ legacy_irq:
/* fall back to legacy interrupt*/
ret = request_irq(pdev->irq, &usb_hcd_irq, IRQF_SHARED,
hcd->irq_descr, hcd);
#else
-static int xhci_try_enable_msi(struct usb_hcd *hcd)
+static inline int xhci_try_enable_msi(struct usb_hcd *hcd)
{
return 0;
}
-static void xhci_cleanup_msix(struct xhci_hcd *xhci)
+static inline void xhci_cleanup_msix(struct xhci_hcd *xhci)
{
}
-static void xhci_msix_sync_irqs(struct xhci_hcd *xhci)
+static inline void xhci_msix_sync_irqs(struct xhci_hcd *xhci)
{
}
if (strstr(dmi_product_name, "Z420") ||
strstr(dmi_product_name, "Z620") ||
- strstr(dmi_product_name, "Z820"))
+ strstr(dmi_product_name, "Z820") ||
+ strstr(dmi_product_name, "Z1 Workstation"))
return true;
return false;
spin_lock_irq(&xhci->lock);
xhci_halt(xhci);
+ /* Workaround for spurious wakeups at shutdown with HSW */
+ if (xhci->quirks & XHCI_SPURIOUS_WAKEUP)
+ xhci_reset(xhci);
spin_unlock_irq(&xhci->lock);
xhci_cleanup_msix(xhci);
xhci_dbg(xhci, "xhci_shutdown completed - status = %x\n",
xhci_readl(xhci, &xhci->op_regs->status));
+
+ /* Yet another workaround for spurious wakeups at shutdown with HSW */
+ if (xhci->quirks & XHCI_SPURIOUS_WAKEUP)
+ pci_set_power_state(to_pci_dev(hcd->self.controller), PCI_D3hot);
}
#ifdef CONFIG_PM
xhci_set_cmd_ring_deq(xhci);
}
+static void xhci_disable_port_wake_on_bits(struct xhci_hcd *xhci)
+{
+ int port_index;
+ __le32 __iomem **port_array;
+ unsigned long flags;
+ u32 t1, t2;
+
+ spin_lock_irqsave(&xhci->lock, flags);
+
+ /* disble usb3 ports Wake bits*/
+ port_index = xhci->num_usb3_ports;
+ port_array = xhci->usb3_ports;
+ while (port_index--) {
+ t1 = readl(port_array[port_index]);
+ t1 = xhci_port_state_to_neutral(t1);
+ t2 = t1 & ~PORT_WAKE_BITS;
+ if (t1 != t2)
+ writel(t2, port_array[port_index]);
+ }
+
+ /* disble usb2 ports Wake bits*/
+ port_index = xhci->num_usb2_ports;
+ port_array = xhci->usb2_ports;
+ while (port_index--) {
+ t1 = readl(port_array[port_index]);
+ t1 = xhci_port_state_to_neutral(t1);
+ t2 = t1 & ~PORT_WAKE_BITS;
+ if (t1 != t2)
+ writel(t2, port_array[port_index]);
+ }
+
+ spin_unlock_irqrestore(&xhci->lock, flags);
+}
+
/*
* Stop HC (not bus-specific)
*
* This is called when the machine transition into S3/S4 mode.
*
*/
-int xhci_suspend(struct xhci_hcd *xhci)
+int xhci_suspend(struct xhci_hcd *xhci, bool do_wakeup)
{
int rc = 0;
+ unsigned int delay = XHCI_MAX_HALT_USEC;
struct usb_hcd *hcd = xhci_to_hcd(xhci);
u32 command;
+ /* Clear root port wake on bits if wakeup not allowed. */
+ if (!do_wakeup)
+ xhci_disable_port_wake_on_bits(xhci);
+
+ /* Don't poll the roothubs on bus suspend. */
+ xhci_dbg(xhci, "%s: stopping port polling.\n", __func__);
+ clear_bit(HCD_FLAG_POLL_RH, &hcd->flags);
+ del_timer_sync(&hcd->rh_timer);
+
+ if (xhci->quirks & XHCI_SUSPEND_DELAY)
+ usleep_range(1000, 1500);
+
spin_lock_irq(&xhci->lock);
clear_bit(HCD_FLAG_HW_ACCESSIBLE, &hcd->flags);
clear_bit(HCD_FLAG_HW_ACCESSIBLE, &xhci->shared_hcd->flags);
command = xhci_readl(xhci, &xhci->op_regs->command);
command &= ~CMD_RUN;
xhci_writel(xhci, command, &xhci->op_regs->command);
+
+ /* Some chips from Fresco Logic need an extraordinary delay */
+ delay *= (xhci->quirks & XHCI_SLOW_SUSPEND) ? 10 : 1;
+
if (handshake(xhci, &xhci->op_regs->status,
- STS_HALT, STS_HALT, XHCI_MAX_HALT_USEC)) {
+ STS_HALT, STS_HALT, delay)) {
xhci_warn(xhci, "WARN: xHC CMD_RUN timeout\n");
spin_unlock_irq(&xhci->lock);
return -ETIMEDOUT;
*/
int xhci_resume(struct xhci_hcd *xhci, bool hibernated)
{
- u32 command, temp = 0;
+ u32 command, temp = 0, status;
struct usb_hcd *hcd = xhci_to_hcd(xhci);
struct usb_hcd *secondary_hcd;
int retval = 0;
+ bool comp_timer_running = false;
/* Wait a bit if either of the roothubs need to settle from the
* transition into bus suspend.
/* If restore operation fails, re-initialize the HC during resume */
if ((temp & STS_SRE) || hibernated) {
+
+ if ((xhci->quirks & XHCI_COMP_MODE_QUIRK) &&
+ !(xhci_all_ports_seen_u0(xhci))) {
+ del_timer_sync(&xhci->comp_mode_recovery_timer);
+ xhci_dbg(xhci, "Compliance Mode Recovery Timer deleted!\n");
+ }
+
/* Let the USB core know _both_ roothubs lost power. */
usb_root_hub_lost_power(xhci->main_hcd->self.root_hub);
usb_root_hub_lost_power(xhci->shared_hcd->self.root_hub);
retval = xhci_init(hcd->primary_hcd);
if (retval)
return retval;
+ comp_timer_running = true;
+
xhci_dbg(xhci, "Start the primary HCD\n");
retval = xhci_run(hcd->primary_hcd);
if (!retval) {
done:
if (retval == 0) {
- usb_hcd_resume_root_hub(hcd);
- usb_hcd_resume_root_hub(xhci->shared_hcd);
+ /* Resume root hubs only when have pending events. */
+ status = readl(&xhci->op_regs->status);
+ if (status & STS_EINT) {
+ usb_hcd_resume_root_hub(hcd);
+ usb_hcd_resume_root_hub(xhci->shared_hcd);
+ }
}
/*
* to suffer the Compliance Mode issue again. It doesn't matter if
* ports have entered previously to U0 before system's suspension.
*/
- if (xhci->quirks & XHCI_COMP_MODE_QUIRK)
+ if ((xhci->quirks & XHCI_COMP_MODE_QUIRK) && !comp_timer_running)
compliance_mode_recovery_timer_init(xhci);
+ /* Re-enable port polling. */
+ xhci_dbg(xhci, "%s: starting port polling.\n", __func__);
+ set_bit(HCD_FLAG_POLL_RH, &hcd->flags);
+ usb_hcd_poll_rh_status(hcd);
+
return retval;
}
#endif /* CONFIG_PM */
}
xhci = hcd_to_xhci(hcd);
- if (xhci->xhc_state & XHCI_STATE_HALTED)
- return -ENODEV;
-
if (check_virt_dev) {
if (!udev->slot_id || !xhci->devs[udev->slot_id]) {
printk(KERN_DEBUG "xHCI %s called with unaddressed "
}
}
+ if (xhci->xhc_state & XHCI_STATE_HALTED)
+ return -ENODEV;
+
return 1;
}
unsigned int ep_index;
struct xhci_ring *ep_ring;
struct xhci_virt_ep *ep;
+ struct xhci_virt_device *vdev;
xhci = hcd_to_xhci(hcd);
spin_lock_irqsave(&xhci->lock, flags);
/* Make sure the URB hasn't completed or been unlinked already */
ret = usb_hcd_check_unlink_urb(hcd, urb, status);
- if (ret || !urb->hcpriv)
+ if (ret)
goto done;
- temp = xhci_readl(xhci, &xhci->op_regs->status);
- if (temp == 0xffffffff || (xhci->xhc_state & XHCI_STATE_HALTED)) {
- xhci_dbg(xhci, "HW died, freeing TD.\n");
- urb_priv = urb->hcpriv;
- for (i = urb_priv->td_cnt; i < urb_priv->length; i++) {
- td = urb_priv->td[i];
- if (!list_empty(&td->td_list))
- list_del_init(&td->td_list);
- if (!list_empty(&td->cancelled_td_list))
- list_del_init(&td->cancelled_td_list);
- }
- usb_hcd_unlink_urb_from_ep(hcd, urb);
- spin_unlock_irqrestore(&xhci->lock, flags);
- usb_hcd_giveback_urb(hcd, urb, -ESHUTDOWN);
- xhci_urb_free_priv(xhci, urb_priv);
- return ret;
- }
- if ((xhci->xhc_state & XHCI_STATE_DYING) ||
- (xhci->xhc_state & XHCI_STATE_HALTED)) {
- xhci_dbg(xhci, "Ep 0x%x: URB %p to be canceled on "
- "non-responsive xHCI host.\n",
- urb->ep->desc.bEndpointAddress, urb);
- /* Let the stop endpoint command watchdog timer (which set this
- * state) finish cleaning up the endpoint TD lists. We must
- * have caught it in the middle of dropping a lock and giving
- * back an URB.
- */
- goto done;
- }
+ /* give back URB now if we can't queue it for cancel */
+ vdev = xhci->devs[urb->dev->slot_id];
+ urb_priv = urb->hcpriv;
+ if (!vdev || !urb_priv)
+ goto err_giveback;
xhci_dbg(xhci, "Cancel URB %p\n", urb);
xhci_dbg(xhci, "Event ring:\n");
xhci_debug_ring(xhci, xhci->event_ring);
ep_index = xhci_get_endpoint_index(&urb->ep->desc);
- ep = &xhci->devs[urb->dev->slot_id]->eps[ep_index];
+ ep = &vdev->eps[ep_index];
ep_ring = xhci_urb_to_transfer_ring(xhci, urb);
- if (!ep_ring) {
- ret = -EINVAL;
- goto done;
- }
+ if (!ep || !ep_ring)
+ goto err_giveback;
xhci_dbg(xhci, "Endpoint ring:\n");
xhci_debug_ring(xhci, ep_ring);
- urb_priv = urb->hcpriv;
+ temp = xhci_readl(xhci, &xhci->op_regs->status);
+ if (temp == 0xffffffff || (xhci->xhc_state & XHCI_STATE_HALTED)) {
+ xhci_dbg(xhci, "HW died, freeing TD.\n");
+ for (i = urb_priv->td_cnt;
+ i < urb_priv->length;
+ i++) {
+ td = urb_priv->td[i];
+ if (!list_empty(&td->td_list))
+ list_del_init(&td->td_list);
+ if (!list_empty(&td->cancelled_td_list))
+ list_del_init(&td->cancelled_td_list);
+ }
+ goto err_giveback;
+ }
for (i = urb_priv->td_cnt; i < urb_priv->length; i++) {
td = urb_priv->td[i];
done:
spin_unlock_irqrestore(&xhci->lock, flags);
return ret;
+
+err_giveback:
+ if (urb_priv)
+ xhci_urb_free_priv(xhci, urb_priv);
+ usb_hcd_unlink_urb_from_ep(hcd, urb);
+ spin_unlock_irqrestore(&xhci->lock, flags);
+ usb_hcd_giveback_urb(hcd, urb, -ESHUTDOWN);
+ return ret;
}
/* Drop an endpoint from a new bandwidth configuration for this device.
static bool xhci_is_sync_in_ep(unsigned int ep_type)
{
- return (ep_type == ISOC_IN_EP || ep_type != INT_IN_EP);
+ return (ep_type == ISOC_IN_EP || ep_type == INT_IN_EP);
}
static unsigned int xhci_get_ss_bw_consumed(struct xhci_bw_info *ep_bw)
ep_index, ep->stopped_stream, ep->stopped_td,
&deq_state);
+ if (!deq_state.new_deq_ptr || !deq_state.new_deq_seg)
+ return;
+
/* HW with the reset endpoint quirk will use the saved dequeue state to
* issue a configure endpoint command later.
*/
}
}
-/* Deal with stalled endpoints. The core should have sent the control message
- * to clear the halt condition. However, we need to make the xHCI hardware
- * reset its sequence number, since a device will expect a sequence number of
- * zero after the halt condition is cleared.
+/* Called when clearing halted device. The core should have sent the control
+ * message to clear the device halt condition. The host side of the halt should
+ * already be cleared with a reset endpoint command issued when the STALL tx
+ * event was received.
+ *
* Context: in_interrupt
*/
+
void xhci_endpoint_reset(struct usb_hcd *hcd,
struct usb_host_endpoint *ep)
{
struct xhci_hcd *xhci;
- struct usb_device *udev;
- unsigned int ep_index;
- unsigned long flags;
- int ret;
- struct xhci_virt_ep *virt_ep;
xhci = hcd_to_xhci(hcd);
- udev = (struct usb_device *) ep->hcpriv;
- /* Called with a root hub endpoint (or an endpoint that wasn't added
- * with xhci_add_endpoint()
- */
- if (!ep->hcpriv)
- return;
- ep_index = xhci_get_endpoint_index(&ep->desc);
- virt_ep = &xhci->devs[udev->slot_id]->eps[ep_index];
- if (!virt_ep->stopped_td) {
- xhci_dbg(xhci, "Endpoint 0x%x not halted, refusing to reset.\n",
- ep->desc.bEndpointAddress);
- return;
- }
- if (usb_endpoint_xfer_control(&ep->desc)) {
- xhci_dbg(xhci, "Control endpoint stall already handled.\n");
- return;
- }
- xhci_dbg(xhci, "Queueing reset endpoint command\n");
- spin_lock_irqsave(&xhci->lock, flags);
- ret = xhci_queue_reset_ep(xhci, udev->slot_id, ep_index);
/*
- * Can't change the ring dequeue pointer until it's transitioned to the
- * stopped state, which is only upon a successful reset endpoint
- * command. Better hope that last command worked!
+ * We might need to implement the config ep cmd in xhci 4.8.1 note:
+ * The Reset Endpoint Command may only be issued to endpoints in the
+ * Halted state. If software wishes reset the Data Toggle or Sequence
+ * Number of an endpoint that isn't in the Halted state, then software
+ * may issue a Configure Endpoint Command with the Drop and Add bits set
+ * for the target endpoint. that is in the Stopped state.
*/
- if (!ret) {
- xhci_cleanup_stalled_ring(xhci, udev, ep_index);
- kfree(virt_ep->stopped_td);
- xhci_ring_cmd_db(xhci);
- }
- virt_ep->stopped_td = NULL;
- virt_ep->stopped_trb = NULL;
- virt_ep->stopped_stream = 0;
- spin_unlock_irqrestore(&xhci->lock, flags);
- if (ret)
- xhci_warn(xhci, "FIXME allocate a new ring segment\n");
+ /* For now just print debug to follow the situation */
+ xhci_dbg(xhci, "Endpoint 0x%x ep reset callback called\n",
+ ep->desc.bEndpointAddress);
}
static int xhci_check_streams_endpoint(struct xhci_hcd *xhci,
return -EINVAL;
}
+ if (virt_dev->tt_info)
+ old_active_eps = virt_dev->tt_info->active_eps;
+
if (virt_dev->udev != udev) {
/* If the virt_dev and the udev does not match, this virt_dev
* may belong to another udev.
{
struct xhci_hcd *xhci = hcd_to_xhci(hcd);
struct xhci_virt_device *virt_dev;
+ struct device *dev = hcd->self.controller;
unsigned long flags;
u32 state;
int i, ret;
+#ifndef CONFIG_USB_DEFAULT_PERSIST
+ /*
+ * We called pm_runtime_get_noresume when the device was attached.
+ * Decrement the counter here to allow controller to runtime suspend
+ * if no devices remain.
+ */
+ if (xhci->quirks & XHCI_RESET_ON_RESUME)
+ pm_runtime_put_noidle(dev);
+#endif
+
ret = xhci_check_args(hcd, udev, NULL, 0, true, __func__);
/* If the host is halted due to driver unload, we still need to free the
* device.
int xhci_alloc_dev(struct usb_hcd *hcd, struct usb_device *udev)
{
struct xhci_hcd *xhci = hcd_to_xhci(hcd);
+ struct device *dev = hcd->self.controller;
unsigned long flags;
int timeleft;
int ret;
goto disable_slot;
}
udev->slot_id = xhci->slot_id;
+
+#ifndef CONFIG_USB_DEFAULT_PERSIST
+ /*
+ * If resetting upon resume, we can't put the controller into runtime
+ * suspend if there is a device attached.
+ */
+ if (xhci->quirks & XHCI_RESET_ON_RESUME)
+ pm_runtime_get_noresume(dev);
+#endif
+
/* Is this a LS or FS device under a HS hub? */
/* Hub or peripherial? */
return 1;
ctrl_ctx->add_flags |= cpu_to_le32(SLOT_FLAG);
slot_ctx = xhci_get_slot_ctx(xhci, config_cmd->in_ctx);
slot_ctx->dev_info |= cpu_to_le32(DEV_HUB);
+ /*
+ * refer to section 6.2.2: MTT should be 0 for full speed hub,
+ * but it may be already set to 1 when setup an xHCI virtual
+ * device, so clear it anyway.
+ */
if (tt->multi)
slot_ctx->dev_info |= cpu_to_le32(DEV_MTT);
+ else if (hdev->speed == USB_SPEED_FULL)
+ slot_ctx->dev_info &= cpu_to_le32(~DEV_MTT);
+
if (xhci->hci_version > 0x95) {
xhci_dbg(xhci, "xHCI version %x needs hub "
"TT think time and number of ports\n",
get_quirks(dev, xhci);
+ /* In xhci controllers which follow xhci 1.0 spec gives a spurious
+ * success event after a short transfer. This quirk will ignore such
+ * spurious event.
+ */
+ if (xhci->hci_version > 0x96)
+ xhci->quirks |= XHCI_SPURIOUS_SUCCESS;
+
/* Make sure the HC is halted. */
retval = xhci_halt(xhci);
if (retval)
{
int retval;
+ if (usb_disabled())
+ return -ENODEV;
+
retval = xhci_register_pci();
if (retval < 0) {
printk(KERN_DEBUG "Problem registering PCI driver.");
git.openpandora.org / pandora-kernel.git / blobdiff