--- /dev/null
+/*
+ * linux/drivers/char/amba.c
+ *
+ * Driver for AMBA serial ports
+ *
+ * Based on drivers/char/serial.c, by Linus Torvalds, Theodore Ts'o.
+ *
+ * Copyright 1999 ARM Limited
+ * Copyright (C) 2000 Deep Blue Solutions Ltd.
+ * Copyright (C) 2010 ST-Ericsson SA
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA
+ *
+ * This is a generic driver for ARM AMBA-type serial ports. They
+ * have a lot of 16550-like features, but are not register compatible.
+ * Note that although they do have CTS, DCD and DSR inputs, they do
+ * not have an RI input, nor do they have DTR or RTS outputs. If
+ * required, these have to be supplied via some other means (eg, GPIO)
+ * and hooked into this driver.
+ */
+
+#if defined(CONFIG_SERIAL_AMBA_PL011_CONSOLE) && defined(CONFIG_MAGIC_SYSRQ)
+#define SUPPORT_SYSRQ
+#endif
+
+#include <linux/module.h>
+#include <linux/ioport.h>
+#include <linux/init.h>
+#include <linux/console.h>
+#include <linux/sysrq.h>
+#include <linux/device.h>
+#include <linux/tty.h>
+#include <linux/tty_flip.h>
+#include <linux/serial_core.h>
+#include <linux/serial.h>
+#include <linux/amba/bus.h>
+#include <linux/amba/serial.h>
+#include <linux/clk.h>
+#include <linux/slab.h>
+#include <linux/dmaengine.h>
+#include <linux/dma-mapping.h>
+#include <linux/scatterlist.h>
+
+#include <asm/io.h>
+#include <asm/sizes.h>
+
+#define UART_NR 14
+
+#define SERIAL_AMBA_MAJOR 204
+#define SERIAL_AMBA_MINOR 64
+#define SERIAL_AMBA_NR UART_NR
+
+#define AMBA_ISR_PASS_LIMIT 256
+
+#define UART_DR_ERROR (UART011_DR_OE|UART011_DR_BE|UART011_DR_PE|UART011_DR_FE)
+#define UART_DUMMY_DR_RX (1 << 16)
+
+/* There is by now at least one vendor with differing details, so handle it */
+struct vendor_data {
+ unsigned int ifls;
+ unsigned int fifosize;
+ unsigned int lcrh_tx;
+ unsigned int lcrh_rx;
+ bool oversampling;
+ bool dma_threshold;
+};
+
+static struct vendor_data vendor_arm = {
+ .ifls = UART011_IFLS_RX4_8|UART011_IFLS_TX4_8,
+ .fifosize = 16,
+ .lcrh_tx = UART011_LCRH,
+ .lcrh_rx = UART011_LCRH,
+ .oversampling = false,
+ .dma_threshold = false,
+};
+
+static struct vendor_data vendor_st = {
+ .ifls = UART011_IFLS_RX_HALF|UART011_IFLS_TX_HALF,
+ .fifosize = 64,
+ .lcrh_tx = ST_UART011_LCRH_TX,
+ .lcrh_rx = ST_UART011_LCRH_RX,
+ .oversampling = true,
+ .dma_threshold = true,
+};
+
+/* Deals with DMA transactions */
+struct pl011_dmatx_data {
+ struct dma_chan *chan;
+ struct scatterlist sg;
+ char *buf;
+ bool queued;
+};
+
+/*
+ * We wrap our port structure around the generic uart_port.
+ */
+struct uart_amba_port {
+ struct uart_port port;
+ struct clk *clk;
+ const struct vendor_data *vendor;
+ unsigned int dmacr; /* dma control reg */
+ unsigned int im; /* interrupt mask */
+ unsigned int old_status;
+ unsigned int fifosize; /* vendor-specific */
+ unsigned int lcrh_tx; /* vendor-specific */
+ unsigned int lcrh_rx; /* vendor-specific */
+ bool autorts;
+ char type[12];
+#ifdef CONFIG_DMA_ENGINE
+ /* DMA stuff */
+ bool using_dma;
+ struct pl011_dmatx_data dmatx;
+#endif
+};
+
+/*
+ * All the DMA operation mode stuff goes inside this ifdef.
+ * This assumes that you have a generic DMA device interface,
+ * no custom DMA interfaces are supported.
+ */
+#ifdef CONFIG_DMA_ENGINE
+
+#define PL011_DMA_BUFFER_SIZE PAGE_SIZE
+
+static void pl011_dma_probe_initcall(struct uart_amba_port *uap)
+{
+ /* DMA is the sole user of the platform data right now */
+ struct amba_pl011_data *plat = uap->port.dev->platform_data;
+ struct dma_slave_config tx_conf = {
+ .dst_addr = uap->port.mapbase + UART01x_DR,
+ .dst_addr_width = DMA_SLAVE_BUSWIDTH_1_BYTE,
+ .direction = DMA_TO_DEVICE,
+ .dst_maxburst = uap->fifosize >> 1,
+ };
+ struct dma_chan *chan;
+ dma_cap_mask_t mask;
+
+ /* We need platform data */
+ if (!plat || !plat->dma_filter) {
+ dev_info(uap->port.dev, "no DMA platform data\n");
+ return;
+ }
+
+ /* Try to acquire a generic DMA engine slave channel */
+ dma_cap_zero(mask);
+ dma_cap_set(DMA_SLAVE, mask);
+
+ chan = dma_request_channel(mask, plat->dma_filter, plat->dma_tx_param);
+ if (!chan) {
+ dev_err(uap->port.dev, "no TX DMA channel!\n");
+ return;
+ }
+
+ dmaengine_slave_config(chan, &tx_conf);
+ uap->dmatx.chan = chan;
+
+ dev_info(uap->port.dev, "DMA channel TX %s\n",
+ dma_chan_name(uap->dmatx.chan));
+}
+
+#ifndef MODULE
+/*
+ * Stack up the UARTs and let the above initcall be done at device
+ * initcall time, because the serial driver is called as an arch
+ * initcall, and at this time the DMA subsystem is not yet registered.
+ * At this point the driver will switch over to using DMA where desired.
+ */
+struct dma_uap {
+ struct list_head node;
+ struct uart_amba_port *uap;
+};
+
+static LIST_HEAD(pl011_dma_uarts);
+
+static int __init pl011_dma_initcall(void)
+{
+ struct list_head *node, *tmp;
+
+ list_for_each_safe(node, tmp, &pl011_dma_uarts) {
+ struct dma_uap *dmau = list_entry(node, struct dma_uap, node);
+ pl011_dma_probe_initcall(dmau->uap);
+ list_del(node);
+ kfree(dmau);
+ }
+ return 0;
+}
+
+device_initcall(pl011_dma_initcall);
+
+static void pl011_dma_probe(struct uart_amba_port *uap)
+{
+ struct dma_uap *dmau = kzalloc(sizeof(struct dma_uap), GFP_KERNEL);
+ if (dmau) {
+ dmau->uap = uap;
+ list_add_tail(&dmau->node, &pl011_dma_uarts);
+ }
+}
+#else
+static void pl011_dma_probe(struct uart_amba_port *uap)
+{
+ pl011_dma_probe_initcall(uap);
+}
+#endif
+
+static void pl011_dma_remove(struct uart_amba_port *uap)
+{
+ /* TODO: remove the initcall if it has not yet executed */
+ if (uap->dmatx.chan)
+ dma_release_channel(uap->dmatx.chan);
+}
+
+
+/* Forward declare this for the refill routine */
+static int pl011_dma_tx_refill(struct uart_amba_port *uap);
+
+/*
+ * The current DMA TX buffer has been sent.
+ * Try to queue up another DMA buffer.
+ */
+static void pl011_dma_tx_callback(void *data)
+{
+ struct uart_amba_port *uap = data;
+ struct pl011_dmatx_data *dmatx = &uap->dmatx;
+ unsigned long flags;
+ u16 dmacr;
+
+ spin_lock_irqsave(&uap->port.lock, flags);
+ if (uap->dmatx.queued)
+ dma_unmap_sg(dmatx->chan->device->dev, &dmatx->sg, 1,
+ DMA_TO_DEVICE);
+
+ dmacr = uap->dmacr;
+ uap->dmacr = dmacr & ~UART011_TXDMAE;
+ writew(uap->dmacr, uap->port.membase + UART011_DMACR);
+
+ /*
+ * If TX DMA was disabled, it means that we've stopped the DMA for
+ * some reason (eg, XOFF received, or we want to send an X-char.)
+ *
+ * Note: we need to be careful here of a potential race between DMA
+ * and the rest of the driver - if the driver disables TX DMA while
+ * a TX buffer completing, we must update the tx queued status to
+ * get further refills (hence we check dmacr).
+ */
+ if (!(dmacr & UART011_TXDMAE) || uart_tx_stopped(&uap->port) ||
+ uart_circ_empty(&uap->port.state->xmit)) {
+ uap->dmatx.queued = false;
+ spin_unlock_irqrestore(&uap->port.lock, flags);
+ return;
+ }
+
+ if (pl011_dma_tx_refill(uap) <= 0) {
+ /*
+ * We didn't queue a DMA buffer for some reason, but we
+ * have data pending to be sent. Re-enable the TX IRQ.
+ */
+ uap->im |= UART011_TXIM;
+ writew(uap->im, uap->port.membase + UART011_IMSC);
+ }
+ spin_unlock_irqrestore(&uap->port.lock, flags);
+}
+
+/*
+ * Try to refill the TX DMA buffer.
+ * Locking: called with port lock held and IRQs disabled.
+ * Returns:
+ * 1 if we queued up a TX DMA buffer.
+ * 0 if we didn't want to handle this by DMA
+ * <0 on error
+ */
+static int pl011_dma_tx_refill(struct uart_amba_port *uap)
+{
+ struct pl011_dmatx_data *dmatx = &uap->dmatx;
+ struct dma_chan *chan = dmatx->chan;
+ struct dma_device *dma_dev = chan->device;
+ struct dma_async_tx_descriptor *desc;
+ struct circ_buf *xmit = &uap->port.state->xmit;
+ unsigned int count;
+
+ /*
+ * Try to avoid the overhead involved in using DMA if the
+ * transaction fits in the first half of the FIFO, by using
+ * the standard interrupt handling. This ensures that we
+ * issue a uart_write_wakeup() at the appropriate time.
+ */
+ count = uart_circ_chars_pending(xmit);
+ if (count < (uap->fifosize >> 1)) {
+ uap->dmatx.queued = false;
+ return 0;
+ }
+
+ /*
+ * Bodge: don't send the last character by DMA, as this
+ * will prevent XON from notifying us to restart DMA.
+ */
+ count -= 1;
+
+ /* Else proceed to copy the TX chars to the DMA buffer and fire DMA */
+ if (count > PL011_DMA_BUFFER_SIZE)
+ count = PL011_DMA_BUFFER_SIZE;
+
+ if (xmit->tail < xmit->head)
+ memcpy(&dmatx->buf[0], &xmit->buf[xmit->tail], count);
+ else {
+ size_t first = UART_XMIT_SIZE - xmit->tail;
+ size_t second = xmit->head;
+
+ memcpy(&dmatx->buf[0], &xmit->buf[xmit->tail], first);
+ if (second)
+ memcpy(&dmatx->buf[first], &xmit->buf[0], second);
+ }
+
+ dmatx->sg.length = count;
+
+ if (dma_map_sg(dma_dev->dev, &dmatx->sg, 1, DMA_TO_DEVICE) != 1) {
+ uap->dmatx.queued = false;
+ dev_dbg(uap->port.dev, "unable to map TX DMA\n");
+ return -EBUSY;
+ }
+
+ desc = dma_dev->device_prep_slave_sg(chan, &dmatx->sg, 1, DMA_TO_DEVICE,
+ DMA_PREP_INTERRUPT | DMA_CTRL_ACK);
+ if (!desc) {
+ dma_unmap_sg(dma_dev->dev, &dmatx->sg, 1, DMA_TO_DEVICE);
+ uap->dmatx.queued = false;
+ /*
+ * If DMA cannot be used right now, we complete this
+ * transaction via IRQ and let the TTY layer retry.
+ */
+ dev_dbg(uap->port.dev, "TX DMA busy\n");
+ return -EBUSY;
+ }
+
+ /* Some data to go along to the callback */
+ desc->callback = pl011_dma_tx_callback;
+ desc->callback_param = uap;
+
+ /* All errors should happen at prepare time */
+ dmaengine_submit(desc);
+
+ /* Fire the DMA transaction */
+ dma_dev->device_issue_pending(chan);
+
+ uap->dmacr |= UART011_TXDMAE;
+ writew(uap->dmacr, uap->port.membase + UART011_DMACR);
+ uap->dmatx.queued = true;
+
+ /*
+ * Now we know that DMA will fire, so advance the ring buffer
+ * with the stuff we just dispatched.
+ */
+ xmit->tail = (xmit->tail + count) & (UART_XMIT_SIZE - 1);
+ uap->port.icount.tx += count;
+
+ if (uart_circ_chars_pending(xmit) < WAKEUP_CHARS)
+ uart_write_wakeup(&uap->port);
+
+ return 1;
+}
+
+/*
+ * We received a transmit interrupt without a pending X-char but with
+ * pending characters.
+ * Locking: called with port lock held and IRQs disabled.
+ * Returns:
+ * false if we want to use PIO to transmit
+ * true if we queued a DMA buffer
+ */
+static bool pl011_dma_tx_irq(struct uart_amba_port *uap)
+{
+ if (!uap->using_dma)
+ return false;
+
+ /*
+ * If we already have a TX buffer queued, but received a
+ * TX interrupt, it will be because we've just sent an X-char.
+ * Ensure the TX DMA is enabled and the TX IRQ is disabled.
+ */
+ if (uap->dmatx.queued) {
+ uap->dmacr |= UART011_TXDMAE;
+ writew(uap->dmacr, uap->port.membase + UART011_DMACR);
+ uap->im &= ~UART011_TXIM;
+ writew(uap->im, uap->port.membase + UART011_IMSC);
+ return true;
+ }
+
+ /*
+ * We don't have a TX buffer queued, so try to queue one.
+ * If we succesfully queued a buffer, mask the TX IRQ.
+ */
+ if (pl011_dma_tx_refill(uap) > 0) {
+ uap->im &= ~UART011_TXIM;
+ writew(uap->im, uap->port.membase + UART011_IMSC);
+ return true;
+ }
+ return false;
+}
+
+/*
+ * Stop the DMA transmit (eg, due to received XOFF).
+ * Locking: called with port lock held and IRQs disabled.
+ */
+static inline void pl011_dma_tx_stop(struct uart_amba_port *uap)
+{
+ if (uap->dmatx.queued) {
+ uap->dmacr &= ~UART011_TXDMAE;
+ writew(uap->dmacr, uap->port.membase + UART011_DMACR);
+ }
+}
+
+/*
+ * Try to start a DMA transmit, or in the case of an XON/OFF
+ * character queued for send, try to get that character out ASAP.
+ * Locking: called with port lock held and IRQs disabled.
+ * Returns:
+ * false if we want the TX IRQ to be enabled
+ * true if we have a buffer queued
+ */
+static inline bool pl011_dma_tx_start(struct uart_amba_port *uap)
+{
+ u16 dmacr;
+
+ if (!uap->using_dma)
+ return false;
+
+ if (!uap->port.x_char) {
+ /* no X-char, try to push chars out in DMA mode */
+ bool ret = true;
+
+ if (!uap->dmatx.queued) {
+ if (pl011_dma_tx_refill(uap) > 0) {
+ uap->im &= ~UART011_TXIM;
+ ret = true;
+ } else {
+ uap->im |= UART011_TXIM;
+ ret = false;
+ }
+ writew(uap->im, uap->port.membase + UART011_IMSC);
+ } else if (!(uap->dmacr & UART011_TXDMAE)) {
+ uap->dmacr |= UART011_TXDMAE;
+ writew(uap->dmacr,
+ uap->port.membase + UART011_DMACR);
+ }
+ return ret;
+ }
+
+ /*
+ * We have an X-char to send. Disable DMA to prevent it loading
+ * the TX fifo, and then see if we can stuff it into the FIFO.
+ */
+ dmacr = uap->dmacr;
+ uap->dmacr &= ~UART011_TXDMAE;
+ writew(uap->dmacr, uap->port.membase + UART011_DMACR);
+
+ if (readw(uap->port.membase + UART01x_FR) & UART01x_FR_TXFF) {
+ /*
+ * No space in the FIFO, so enable the transmit interrupt
+ * so we know when there is space. Note that once we've
+ * loaded the character, we should just re-enable DMA.
+ */
+ return false;
+ }
+
+ writew(uap->port.x_char, uap->port.membase + UART01x_DR);
+ uap->port.icount.tx++;
+ uap->port.x_char = 0;
+
+ /* Success - restore the DMA state */
+ uap->dmacr = dmacr;
+ writew(dmacr, uap->port.membase + UART011_DMACR);
+
+ return true;
+}
+
+/*
+ * Flush the transmit buffer.
+ * Locking: called with port lock held and IRQs disabled.
+ */
+static void pl011_dma_flush_buffer(struct uart_port *port)
+{
+ struct uart_amba_port *uap = (struct uart_amba_port *)port;
+
+ if (!uap->using_dma)
+ return;
+
+ /* Avoid deadlock with the DMA engine callback */
+ spin_unlock(&uap->port.lock);
+ dmaengine_terminate_all(uap->dmatx.chan);
+ spin_lock(&uap->port.lock);
+ if (uap->dmatx.queued) {
+ dma_unmap_sg(uap->dmatx.chan->device->dev, &uap->dmatx.sg, 1,
+ DMA_TO_DEVICE);
+ uap->dmatx.queued = false;
+ uap->dmacr &= ~UART011_TXDMAE;
+ writew(uap->dmacr, uap->port.membase + UART011_DMACR);
+ }
+}
+
+
+static void pl011_dma_startup(struct uart_amba_port *uap)
+{
+ if (!uap->dmatx.chan)
+ return;
+
+ uap->dmatx.buf = kmalloc(PL011_DMA_BUFFER_SIZE, GFP_KERNEL);
+ if (!uap->dmatx.buf) {
+ dev_err(uap->port.dev, "no memory for DMA TX buffer\n");
+ uap->port.fifosize = uap->fifosize;
+ return;
+ }
+
+ sg_init_one(&uap->dmatx.sg, uap->dmatx.buf, PL011_DMA_BUFFER_SIZE);
+
+ /* The DMA buffer is now the FIFO the TTY subsystem can use */
+ uap->port.fifosize = PL011_DMA_BUFFER_SIZE;
+ uap->using_dma = true;
+
+ /* Turn on DMA error (RX/TX will be enabled on demand) */
+ uap->dmacr |= UART011_DMAONERR;
+ writew(uap->dmacr, uap->port.membase + UART011_DMACR);
+
+ /*
+ * ST Micro variants has some specific dma burst threshold
+ * compensation. Set this to 16 bytes, so burst will only
+ * be issued above/below 16 bytes.
+ */
+ if (uap->vendor->dma_threshold)
+ writew(ST_UART011_DMAWM_RX_16 | ST_UART011_DMAWM_TX_16,
+ uap->port.membase + ST_UART011_DMAWM);
+}
+
+static void pl011_dma_shutdown(struct uart_amba_port *uap)
+{
+ if (!uap->using_dma)
+ return;
+
+ /* Disable RX and TX DMA */
+ while (readw(uap->port.membase + UART01x_FR) & UART01x_FR_BUSY)
+ barrier();
+
+ spin_lock_irq(&uap->port.lock);
+ uap->dmacr &= ~(UART011_DMAONERR | UART011_RXDMAE | UART011_TXDMAE);
+ writew(uap->dmacr, uap->port.membase + UART011_DMACR);
+ spin_unlock_irq(&uap->port.lock);
+
+ /* In theory, this should already be done by pl011_dma_flush_buffer */
+ dmaengine_terminate_all(uap->dmatx.chan);
+ if (uap->dmatx.queued) {
+ dma_unmap_sg(uap->dmatx.chan->device->dev, &uap->dmatx.sg, 1,
+ DMA_TO_DEVICE);
+ uap->dmatx.queued = false;
+ }
+
+ kfree(uap->dmatx.buf);
+
+ uap->using_dma = false;
+}
+
+#else
+/* Blank functions if the DMA engine is not available */
+static inline void pl011_dma_probe(struct uart_amba_port *uap)
+{
+}
+
+static inline void pl011_dma_remove(struct uart_amba_port *uap)
+{
+}
+
+static inline void pl011_dma_startup(struct uart_amba_port *uap)
+{
+}
+
+static inline void pl011_dma_shutdown(struct uart_amba_port *uap)
+{
+}
+
+static inline bool pl011_dma_tx_irq(struct uart_amba_port *uap)
+{
+ return false;
+}
+
+static inline void pl011_dma_tx_stop(struct uart_amba_port *uap)
+{
+}
+
+static inline bool pl011_dma_tx_start(struct uart_amba_port *uap)
+{
+ return false;
+}
+
+#define pl011_dma_flush_buffer NULL
+#endif
+
+
+static void pl011_stop_tx(struct uart_port *port)
+{
+ struct uart_amba_port *uap = (struct uart_amba_port *)port;
+
+ uap->im &= ~UART011_TXIM;
+ writew(uap->im, uap->port.membase + UART011_IMSC);
+ pl011_dma_tx_stop(uap);
+}
+
+static void pl011_start_tx(struct uart_port *port)
+{
+ struct uart_amba_port *uap = (struct uart_amba_port *)port;
+
+ if (!pl011_dma_tx_start(uap)) {
+ uap->im |= UART011_TXIM;
+ writew(uap->im, uap->port.membase + UART011_IMSC);
+ }
+}
+
+static void pl011_stop_rx(struct uart_port *port)
+{
+ struct uart_amba_port *uap = (struct uart_amba_port *)port;
+
+ uap->im &= ~(UART011_RXIM|UART011_RTIM|UART011_FEIM|
+ UART011_PEIM|UART011_BEIM|UART011_OEIM);
+ writew(uap->im, uap->port.membase + UART011_IMSC);
+}
+
+static void pl011_enable_ms(struct uart_port *port)
+{
+ struct uart_amba_port *uap = (struct uart_amba_port *)port;
+
+ uap->im |= UART011_RIMIM|UART011_CTSMIM|UART011_DCDMIM|UART011_DSRMIM;
+ writew(uap->im, uap->port.membase + UART011_IMSC);
+}
+
+static void pl011_rx_chars(struct uart_amba_port *uap)
+{
+ struct tty_struct *tty = uap->port.state->port.tty;
+ unsigned int status, ch, flag, max_count = 256;
+
+ status = readw(uap->port.membase + UART01x_FR);
+ while ((status & UART01x_FR_RXFE) == 0 && max_count--) {
+ ch = readw(uap->port.membase + UART01x_DR) | UART_DUMMY_DR_RX;
+ flag = TTY_NORMAL;
+ uap->port.icount.rx++;
+
+ /*
+ * Note that the error handling code is
+ * out of the main execution path
+ */
+ if (unlikely(ch & UART_DR_ERROR)) {
+ if (ch & UART011_DR_BE) {
+ ch &= ~(UART011_DR_FE | UART011_DR_PE);
+ uap->port.icount.brk++;
+ if (uart_handle_break(&uap->port))
+ goto ignore_char;
+ } else if (ch & UART011_DR_PE)
+ uap->port.icount.parity++;
+ else if (ch & UART011_DR_FE)
+ uap->port.icount.frame++;
+ if (ch & UART011_DR_OE)
+ uap->port.icount.overrun++;
+
+ ch &= uap->port.read_status_mask;
+
+ if (ch & UART011_DR_BE)
+ flag = TTY_BREAK;
+ else if (ch & UART011_DR_PE)
+ flag = TTY_PARITY;
+ else if (ch & UART011_DR_FE)
+ flag = TTY_FRAME;
+ }
+
+ if (uart_handle_sysrq_char(&uap->port, ch & 255))
+ goto ignore_char;
+
+ uart_insert_char(&uap->port, ch, UART011_DR_OE, ch, flag);
+
+ ignore_char:
+ status = readw(uap->port.membase + UART01x_FR);
+ }
+ spin_unlock(&uap->port.lock);
+ tty_flip_buffer_push(tty);
+ spin_lock(&uap->port.lock);
+}
+
+static void pl011_tx_chars(struct uart_amba_port *uap)
+{
+ struct circ_buf *xmit = &uap->port.state->xmit;
+ int count;
+
+ if (uap->port.x_char) {
+ writew(uap->port.x_char, uap->port.membase + UART01x_DR);
+ uap->port.icount.tx++;
+ uap->port.x_char = 0;
+ return;
+ }
+ if (uart_circ_empty(xmit) || uart_tx_stopped(&uap->port)) {
+ pl011_stop_tx(&uap->port);
+ return;
+ }
+
+ /* If we are using DMA mode, try to send some characters. */
+ if (pl011_dma_tx_irq(uap))
+ return;
+
+ count = uap->fifosize >> 1;
+ do {
+ writew(xmit->buf[xmit->tail], uap->port.membase + UART01x_DR);
+ xmit->tail = (xmit->tail + 1) & (UART_XMIT_SIZE - 1);
+ uap->port.icount.tx++;
+ if (uart_circ_empty(xmit))
+ break;
+ } while (--count > 0);
+
+ if (uart_circ_chars_pending(xmit) < WAKEUP_CHARS)
+ uart_write_wakeup(&uap->port);
+
+ if (uart_circ_empty(xmit))
+ pl011_stop_tx(&uap->port);
+}
+
+static void pl011_modem_status(struct uart_amba_port *uap)
+{
+ unsigned int status, delta;
+
+ status = readw(uap->port.membase + UART01x_FR) & UART01x_FR_MODEM_ANY;
+
+ delta = status ^ uap->old_status;
+ uap->old_status = status;
+
+ if (!delta)
+ return;
+
+ if (delta & UART01x_FR_DCD)
+ uart_handle_dcd_change(&uap->port, status & UART01x_FR_DCD);
+
+ if (delta & UART01x_FR_DSR)
+ uap->port.icount.dsr++;
+
+ if (delta & UART01x_FR_CTS)
+ uart_handle_cts_change(&uap->port, status & UART01x_FR_CTS);
+
+ wake_up_interruptible(&uap->port.state->port.delta_msr_wait);
+}
+
+static irqreturn_t pl011_int(int irq, void *dev_id)
+{
+ struct uart_amba_port *uap = dev_id;
+ unsigned long flags;
+ unsigned int status, pass_counter = AMBA_ISR_PASS_LIMIT;
+ int handled = 0;
+
+ spin_lock_irqsave(&uap->port.lock, flags);
+
+ status = readw(uap->port.membase + UART011_MIS);
+ if (status) {
+ do {
+ writew(status & ~(UART011_TXIS|UART011_RTIS|
+ UART011_RXIS),
+ uap->port.membase + UART011_ICR);
+
+ if (status & (UART011_RTIS|UART011_RXIS))
+ pl011_rx_chars(uap);
+ if (status & (UART011_DSRMIS|UART011_DCDMIS|
+ UART011_CTSMIS|UART011_RIMIS))
+ pl011_modem_status(uap);
+ if (status & UART011_TXIS)
+ pl011_tx_chars(uap);
+
+ if (pass_counter-- == 0)
+ break;
+
+ status = readw(uap->port.membase + UART011_MIS);
+ } while (status != 0);
+ handled = 1;
+ }
+
+ spin_unlock_irqrestore(&uap->port.lock, flags);
+
+ return IRQ_RETVAL(handled);
+}
+
+static unsigned int pl01x_tx_empty(struct uart_port *port)
+{
+ struct uart_amba_port *uap = (struct uart_amba_port *)port;
+ unsigned int status = readw(uap->port.membase + UART01x_FR);
+ return status & (UART01x_FR_BUSY|UART01x_FR_TXFF) ? 0 : TIOCSER_TEMT;
+}
+
+static unsigned int pl01x_get_mctrl(struct uart_port *port)
+{
+ struct uart_amba_port *uap = (struct uart_amba_port *)port;
+ unsigned int result = 0;
+ unsigned int status = readw(uap->port.membase + UART01x_FR);
+
+#define TIOCMBIT(uartbit, tiocmbit) \
+ if (status & uartbit) \
+ result |= tiocmbit
+
+ TIOCMBIT(UART01x_FR_DCD, TIOCM_CAR);
+ TIOCMBIT(UART01x_FR_DSR, TIOCM_DSR);
+ TIOCMBIT(UART01x_FR_CTS, TIOCM_CTS);
+ TIOCMBIT(UART011_FR_RI, TIOCM_RNG);
+#undef TIOCMBIT
+ return result;
+}
+
+static void pl011_set_mctrl(struct uart_port *port, unsigned int mctrl)
+{
+ struct uart_amba_port *uap = (struct uart_amba_port *)port;
+ unsigned int cr;
+
+ cr = readw(uap->port.membase + UART011_CR);
+
+#define TIOCMBIT(tiocmbit, uartbit) \
+ if (mctrl & tiocmbit) \
+ cr |= uartbit; \
+ else \
+ cr &= ~uartbit
+
+ TIOCMBIT(TIOCM_RTS, UART011_CR_RTS);
+ TIOCMBIT(TIOCM_DTR, UART011_CR_DTR);
+ TIOCMBIT(TIOCM_OUT1, UART011_CR_OUT1);
+ TIOCMBIT(TIOCM_OUT2, UART011_CR_OUT2);
+ TIOCMBIT(TIOCM_LOOP, UART011_CR_LBE);
+
+ if (uap->autorts) {
+ /* We need to disable auto-RTS if we want to turn RTS off */
+ TIOCMBIT(TIOCM_RTS, UART011_CR_RTSEN);
+ }
+#undef TIOCMBIT
+
+ writew(cr, uap->port.membase + UART011_CR);
+}
+
+static void pl011_break_ctl(struct uart_port *port, int break_state)
+{
+ struct uart_amba_port *uap = (struct uart_amba_port *)port;
+ unsigned long flags;
+ unsigned int lcr_h;
+
+ spin_lock_irqsave(&uap->port.lock, flags);
+ lcr_h = readw(uap->port.membase + uap->lcrh_tx);
+ if (break_state == -1)
+ lcr_h |= UART01x_LCRH_BRK;
+ else
+ lcr_h &= ~UART01x_LCRH_BRK;
+ writew(lcr_h, uap->port.membase + uap->lcrh_tx);
+ spin_unlock_irqrestore(&uap->port.lock, flags);
+}
+
+#ifdef CONFIG_CONSOLE_POLL
+static int pl010_get_poll_char(struct uart_port *port)
+{
+ struct uart_amba_port *uap = (struct uart_amba_port *)port;
+ unsigned int status;
+
+ status = readw(uap->port.membase + UART01x_FR);
+ if (status & UART01x_FR_RXFE)
+ return NO_POLL_CHAR;
+
+ return readw(uap->port.membase + UART01x_DR);
+}
+
+static void pl010_put_poll_char(struct uart_port *port,
+ unsigned char ch)
+{
+ struct uart_amba_port *uap = (struct uart_amba_port *)port;
+
+ while (readw(uap->port.membase + UART01x_FR) & UART01x_FR_TXFF)
+ barrier();
+
+ writew(ch, uap->port.membase + UART01x_DR);
+}
+
+#endif /* CONFIG_CONSOLE_POLL */
+
+static int pl011_startup(struct uart_port *port)
+{
+ struct uart_amba_port *uap = (struct uart_amba_port *)port;
+ unsigned int cr;
+ int retval;
+
+ /*
+ * Try to enable the clock producer.
+ */
+ retval = clk_enable(uap->clk);
+ if (retval)
+ goto out;
+
+ uap->port.uartclk = clk_get_rate(uap->clk);
+
+ /*
+ * Allocate the IRQ
+ */
+ retval = request_irq(uap->port.irq, pl011_int, 0, "uart-pl011", uap);
+ if (retval)
+ goto clk_dis;
+
+ writew(uap->vendor->ifls, uap->port.membase + UART011_IFLS);
+
+ /*
+ * Provoke TX FIFO interrupt into asserting.
+ */
+ cr = UART01x_CR_UARTEN | UART011_CR_TXE | UART011_CR_LBE;
+ writew(cr, uap->port.membase + UART011_CR);
+ writew(0, uap->port.membase + UART011_FBRD);
+ writew(1, uap->port.membase + UART011_IBRD);
+ writew(0, uap->port.membase + uap->lcrh_rx);
+ if (uap->lcrh_tx != uap->lcrh_rx) {
+ int i;
+ /*
+ * Wait 10 PCLKs before writing LCRH_TX register,
+ * to get this delay write read only register 10 times
+ */
+ for (i = 0; i < 10; ++i)
+ writew(0xff, uap->port.membase + UART011_MIS);
+ writew(0, uap->port.membase + uap->lcrh_tx);
+ }
+ writew(0, uap->port.membase + UART01x_DR);
+ while (readw(uap->port.membase + UART01x_FR) & UART01x_FR_BUSY)
+ barrier();
+
+ cr = UART01x_CR_UARTEN | UART011_CR_RXE | UART011_CR_TXE;
+ writew(cr, uap->port.membase + UART011_CR);
+
+ /* Clear pending error interrupts */
+ writew(UART011_OEIS | UART011_BEIS | UART011_PEIS | UART011_FEIS,
+ uap->port.membase + UART011_ICR);
+
+ /*
+ * initialise the old status of the modem signals
+ */
+ uap->old_status = readw(uap->port.membase + UART01x_FR) & UART01x_FR_MODEM_ANY;
+
+ /* Startup DMA */
+ pl011_dma_startup(uap);
+
+ /*
+ * Finally, enable interrupts
+ */
+ spin_lock_irq(&uap->port.lock);
+ uap->im = UART011_RXIM | UART011_RTIM;
+ writew(uap->im, uap->port.membase + UART011_IMSC);
+ spin_unlock_irq(&uap->port.lock);
+
+ return 0;
+
+ clk_dis:
+ clk_disable(uap->clk);
+ out:
+ return retval;
+}
+
+static void pl011_shutdown_channel(struct uart_amba_port *uap,
+ unsigned int lcrh)
+{
+ unsigned long val;
+
+ val = readw(uap->port.membase + lcrh);
+ val &= ~(UART01x_LCRH_BRK | UART01x_LCRH_FEN);
+ writew(val, uap->port.membase + lcrh);
+}
+
+static void pl011_shutdown(struct uart_port *port)
+{
+ struct uart_amba_port *uap = (struct uart_amba_port *)port;
+
+ /*
+ * disable all interrupts
+ */
+ spin_lock_irq(&uap->port.lock);
+ uap->im = 0;
+ writew(uap->im, uap->port.membase + UART011_IMSC);
+ writew(0xffff, uap->port.membase + UART011_ICR);
+ spin_unlock_irq(&uap->port.lock);
+
+ pl011_dma_shutdown(uap);
+
+ /*
+ * Free the interrupt
+ */
+ free_irq(uap->port.irq, uap);
+
+ /*
+ * disable the port
+ */
+ uap->autorts = false;
+ writew(UART01x_CR_UARTEN | UART011_CR_TXE, uap->port.membase + UART011_CR);
+
+ /*
+ * disable break condition and fifos
+ */
+ pl011_shutdown_channel(uap, uap->lcrh_rx);
+ if (uap->lcrh_rx != uap->lcrh_tx)
+ pl011_shutdown_channel(uap, uap->lcrh_tx);
+
+ /*
+ * Shut down the clock producer
+ */
+ clk_disable(uap->clk);
+}
+
+static void
+pl011_set_termios(struct uart_port *port, struct ktermios *termios,
+ struct ktermios *old)
+{
+ struct uart_amba_port *uap = (struct uart_amba_port *)port;
+ unsigned int lcr_h, old_cr;
+ unsigned long flags;
+ unsigned int baud, quot, clkdiv;
+
+ if (uap->vendor->oversampling)
+ clkdiv = 8;
+ else
+ clkdiv = 16;
+
+ /*
+ * Ask the core to calculate the divisor for us.
+ */
+ baud = uart_get_baud_rate(port, termios, old, 0,
+ port->uartclk / clkdiv);
+
+ if (baud > port->uartclk/16)
+ quot = DIV_ROUND_CLOSEST(port->uartclk * 8, baud);
+ else
+ quot = DIV_ROUND_CLOSEST(port->uartclk * 4, baud);
+
+ switch (termios->c_cflag & CSIZE) {
+ case CS5:
+ lcr_h = UART01x_LCRH_WLEN_5;
+ break;
+ case CS6:
+ lcr_h = UART01x_LCRH_WLEN_6;
+ break;
+ case CS7:
+ lcr_h = UART01x_LCRH_WLEN_7;
+ break;
+ default: // CS8
+ lcr_h = UART01x_LCRH_WLEN_8;
+ break;
+ }
+ if (termios->c_cflag & CSTOPB)
+ lcr_h |= UART01x_LCRH_STP2;
+ if (termios->c_cflag & PARENB) {
+ lcr_h |= UART01x_LCRH_PEN;
+ if (!(termios->c_cflag & PARODD))
+ lcr_h |= UART01x_LCRH_EPS;
+ }
+ if (uap->fifosize > 1)
+ lcr_h |= UART01x_LCRH_FEN;
+
+ spin_lock_irqsave(&port->lock, flags);
+
+ /*
+ * Update the per-port timeout.
+ */
+ uart_update_timeout(port, termios->c_cflag, baud);
+
+ port->read_status_mask = UART011_DR_OE | 255;
+ if (termios->c_iflag & INPCK)
+ port->read_status_mask |= UART011_DR_FE | UART011_DR_PE;
+ if (termios->c_iflag & (BRKINT | PARMRK))
+ port->read_status_mask |= UART011_DR_BE;
+
+ /*
+ * Characters to ignore
+ */
+ port->ignore_status_mask = 0;
+ if (termios->c_iflag & IGNPAR)
+ port->ignore_status_mask |= UART011_DR_FE | UART011_DR_PE;
+ if (termios->c_iflag & IGNBRK) {
+ port->ignore_status_mask |= UART011_DR_BE;
+ /*
+ * If we're ignoring parity and break indicators,
+ * ignore overruns too (for real raw support).
+ */
+ if (termios->c_iflag & IGNPAR)
+ port->ignore_status_mask |= UART011_DR_OE;
+ }
+
+ /*
+ * Ignore all characters if CREAD is not set.
+ */
+ if ((termios->c_cflag & CREAD) == 0)
+ port->ignore_status_mask |= UART_DUMMY_DR_RX;
+
+ if (UART_ENABLE_MS(port, termios->c_cflag))
+ pl011_enable_ms(port);
+
+ /* first, disable everything */
+ old_cr = readw(port->membase + UART011_CR);
+ writew(0, port->membase + UART011_CR);
+
+ if (termios->c_cflag & CRTSCTS) {
+ if (old_cr & UART011_CR_RTS)
+ old_cr |= UART011_CR_RTSEN;
+
+ old_cr |= UART011_CR_CTSEN;
+ uap->autorts = true;
+ } else {
+ old_cr &= ~(UART011_CR_CTSEN | UART011_CR_RTSEN);
+ uap->autorts = false;
+ }
+
+ if (uap->vendor->oversampling) {
+ if (baud > port->uartclk / 16)
+ old_cr |= ST_UART011_CR_OVSFACT;
+ else
+ old_cr &= ~ST_UART011_CR_OVSFACT;
+ }
+
+ /* Set baud rate */
+ writew(quot & 0x3f, port->membase + UART011_FBRD);
+ writew(quot >> 6, port->membase + UART011_IBRD);
+
+ /*
+ * ----------v----------v----------v----------v-----
+ * NOTE: MUST BE WRITTEN AFTER UARTLCR_M & UARTLCR_L
+ * ----------^----------^----------^----------^-----
+ */
+ writew(lcr_h, port->membase + uap->lcrh_rx);
+ if (uap->lcrh_rx != uap->lcrh_tx) {
+ int i;
+ /*
+ * Wait 10 PCLKs before writing LCRH_TX register,
+ * to get this delay write read only register 10 times
+ */
+ for (i = 0; i < 10; ++i)
+ writew(0xff, uap->port.membase + UART011_MIS);
+ writew(lcr_h, port->membase + uap->lcrh_tx);
+ }
+ writew(old_cr, port->membase + UART011_CR);
+
+ spin_unlock_irqrestore(&port->lock, flags);
+}
+
+static const char *pl011_type(struct uart_port *port)
+{
+ struct uart_amba_port *uap = (struct uart_amba_port *)port;
+ return uap->port.type == PORT_AMBA ? uap->type : NULL;
+}
+
+/*
+ * Release the memory region(s) being used by 'port'
+ */
+static void pl010_release_port(struct uart_port *port)
+{
+ release_mem_region(port->mapbase, SZ_4K);
+}
+
+/*
+ * Request the memory region(s) being used by 'port'
+ */
+static int pl010_request_port(struct uart_port *port)
+{
+ return request_mem_region(port->mapbase, SZ_4K, "uart-pl011")
+ != NULL ? 0 : -EBUSY;
+}
+
+/*
+ * Configure/autoconfigure the port.
+ */
+static void pl010_config_port(struct uart_port *port, int flags)
+{
+ if (flags & UART_CONFIG_TYPE) {
+ port->type = PORT_AMBA;
+ pl010_request_port(port);
+ }
+}
+
+/*
+ * verify the new serial_struct (for TIOCSSERIAL).
+ */
+static int pl010_verify_port(struct uart_port *port, struct serial_struct *ser)
+{
+ int ret = 0;
+ if (ser->type != PORT_UNKNOWN && ser->type != PORT_AMBA)
+ ret = -EINVAL;
+ if (ser->irq < 0 || ser->irq >= nr_irqs)
+ ret = -EINVAL;
+ if (ser->baud_base < 9600)
+ ret = -EINVAL;
+ return ret;
+}
+
+static struct uart_ops amba_pl011_pops = {
+ .tx_empty = pl01x_tx_empty,
+ .set_mctrl = pl011_set_mctrl,
+ .get_mctrl = pl01x_get_mctrl,
+ .stop_tx = pl011_stop_tx,
+ .start_tx = pl011_start_tx,
+ .stop_rx = pl011_stop_rx,
+ .enable_ms = pl011_enable_ms,
+ .break_ctl = pl011_break_ctl,
+ .startup = pl011_startup,
+ .shutdown = pl011_shutdown,
+ .flush_buffer = pl011_dma_flush_buffer,
+ .set_termios = pl011_set_termios,
+ .type = pl011_type,
+ .release_port = pl010_release_port,
+ .request_port = pl010_request_port,
+ .config_port = pl010_config_port,
+ .verify_port = pl010_verify_port,
+#ifdef CONFIG_CONSOLE_POLL
+ .poll_get_char = pl010_get_poll_char,
+ .poll_put_char = pl010_put_poll_char,
+#endif
+};
+
+static struct uart_amba_port *amba_ports[UART_NR];
+
+#ifdef CONFIG_SERIAL_AMBA_PL011_CONSOLE
+
+static void pl011_console_putchar(struct uart_port *port, int ch)
+{
+ struct uart_amba_port *uap = (struct uart_amba_port *)port;
+
+ while (readw(uap->port.membase + UART01x_FR) & UART01x_FR_TXFF)
+ barrier();
+ writew(ch, uap->port.membase + UART01x_DR);
+}
+
+static void
+pl011_console_write(struct console *co, const char *s, unsigned int count)
+{
+ struct uart_amba_port *uap = amba_ports[co->index];
+ unsigned int status, old_cr, new_cr;
+
+ clk_enable(uap->clk);
+
+ /*
+ * First save the CR then disable the interrupts
+ */
+ old_cr = readw(uap->port.membase + UART011_CR);
+ new_cr = old_cr & ~UART011_CR_CTSEN;
+ new_cr |= UART01x_CR_UARTEN | UART011_CR_TXE;
+ writew(new_cr, uap->port.membase + UART011_CR);
+
+ uart_console_write(&uap->port, s, count, pl011_console_putchar);
+
+ /*
+ * Finally, wait for transmitter to become empty
+ * and restore the TCR
+ */
+ do {
+ status = readw(uap->port.membase + UART01x_FR);
+ } while (status & UART01x_FR_BUSY);
+ writew(old_cr, uap->port.membase + UART011_CR);
+
+ clk_disable(uap->clk);
+}
+
+static void __init
+pl011_console_get_options(struct uart_amba_port *uap, int *baud,
+ int *parity, int *bits)
+{
+ if (readw(uap->port.membase + UART011_CR) & UART01x_CR_UARTEN) {
+ unsigned int lcr_h, ibrd, fbrd;
+
+ lcr_h = readw(uap->port.membase + uap->lcrh_tx);
+
+ *parity = 'n';
+ if (lcr_h & UART01x_LCRH_PEN) {
+ if (lcr_h & UART01x_LCRH_EPS)
+ *parity = 'e';
+ else
+ *parity = 'o';
+ }
+
+ if ((lcr_h & 0x60) == UART01x_LCRH_WLEN_7)
+ *bits = 7;
+ else
+ *bits = 8;
+
+ ibrd = readw(uap->port.membase + UART011_IBRD);
+ fbrd = readw(uap->port.membase + UART011_FBRD);
+
+ *baud = uap->port.uartclk * 4 / (64 * ibrd + fbrd);
+
+ if (uap->vendor->oversampling) {
+ if (readw(uap->port.membase + UART011_CR)
+ & ST_UART011_CR_OVSFACT)
+ *baud *= 2;
+ }
+ }
+}
+
+static int __init pl011_console_setup(struct console *co, char *options)
+{
+ struct uart_amba_port *uap;
+ int baud = 38400;
+ int bits = 8;
+ int parity = 'n';
+ int flow = 'n';
+
+ /*
+ * Check whether an invalid uart number has been specified, and
+ * if so, search for the first available port that does have
+ * console support.
+ */
+ if (co->index >= UART_NR)
+ co->index = 0;
+ uap = amba_ports[co->index];
+ if (!uap)
+ return -ENODEV;
+
+ uap->port.uartclk = clk_get_rate(uap->clk);
+
+ if (options)
+ uart_parse_options(options, &baud, &parity, &bits, &flow);
+ else
+ pl011_console_get_options(uap, &baud, &parity, &bits);
+
+ return uart_set_options(&uap->port, co, baud, parity, bits, flow);
+}
+
+static struct uart_driver amba_reg;
+static struct console amba_console = {
+ .name = "ttyAMA",
+ .write = pl011_console_write,
+ .device = uart_console_device,
+ .setup = pl011_console_setup,
+ .flags = CON_PRINTBUFFER,
+ .index = -1,
+ .data = &amba_reg,
+};
+
+#define AMBA_CONSOLE (&amba_console)
+#else
+#define AMBA_CONSOLE NULL
+#endif
+
+static struct uart_driver amba_reg = {
+ .owner = THIS_MODULE,
+ .driver_name = "ttyAMA",
+ .dev_name = "ttyAMA",
+ .major = SERIAL_AMBA_MAJOR,
+ .minor = SERIAL_AMBA_MINOR,
+ .nr = UART_NR,
+ .cons = AMBA_CONSOLE,
+};
+
+static int pl011_probe(struct amba_device *dev, struct amba_id *id)
+{
+ struct uart_amba_port *uap;
+ struct vendor_data *vendor = id->data;
+ void __iomem *base;
+ int i, ret;
+
+ for (i = 0; i < ARRAY_SIZE(amba_ports); i++)
+ if (amba_ports[i] == NULL)
+ break;
+
+ if (i == ARRAY_SIZE(amba_ports)) {
+ ret = -EBUSY;
+ goto out;
+ }
+
+ uap = kzalloc(sizeof(struct uart_amba_port), GFP_KERNEL);
+ if (uap == NULL) {
+ ret = -ENOMEM;
+ goto out;
+ }
+
+ base = ioremap(dev->res.start, resource_size(&dev->res));
+ if (!base) {
+ ret = -ENOMEM;
+ goto free;
+ }
+
+ uap->clk = clk_get(&dev->dev, NULL);
+ if (IS_ERR(uap->clk)) {
+ ret = PTR_ERR(uap->clk);
+ goto unmap;
+ }
+
+ uap->vendor = vendor;
+ uap->lcrh_rx = vendor->lcrh_rx;
+ uap->lcrh_tx = vendor->lcrh_tx;
+ uap->fifosize = vendor->fifosize;
+ uap->port.dev = &dev->dev;
+ uap->port.mapbase = dev->res.start;
+ uap->port.membase = base;
+ uap->port.iotype = UPIO_MEM;
+ uap->port.irq = dev->irq[0];
+ uap->port.fifosize = uap->fifosize;
+ uap->port.ops = &amba_pl011_pops;
+ uap->port.flags = UPF_BOOT_AUTOCONF;
+ uap->port.line = i;
+ pl011_dma_probe(uap);
+
+ snprintf(uap->type, sizeof(uap->type), "PL011 rev%u", amba_rev(dev));
+
+ amba_ports[i] = uap;
+
+ amba_set_drvdata(dev, uap);
+ ret = uart_add_one_port(&amba_reg, &uap->port);
+ if (ret) {
+ amba_set_drvdata(dev, NULL);
+ amba_ports[i] = NULL;
+ pl011_dma_remove(uap);
+ clk_put(uap->clk);
+ unmap:
+ iounmap(base);
+ free:
+ kfree(uap);
+ }
+ out:
+ return ret;
+}
+
+static int pl011_remove(struct amba_device *dev)
+{
+ struct uart_amba_port *uap = amba_get_drvdata(dev);
+ int i;
+
+ amba_set_drvdata(dev, NULL);
+
+ uart_remove_one_port(&amba_reg, &uap->port);
+
+ for (i = 0; i < ARRAY_SIZE(amba_ports); i++)
+ if (amba_ports[i] == uap)
+ amba_ports[i] = NULL;
+
+ pl011_dma_remove(uap);
+ iounmap(uap->port.membase);
+ clk_put(uap->clk);
+ kfree(uap);
+ return 0;
+}
+
+#ifdef CONFIG_PM
+static int pl011_suspend(struct amba_device *dev, pm_message_t state)
+{
+ struct uart_amba_port *uap = amba_get_drvdata(dev);
+
+ if (!uap)
+ return -EINVAL;
+
+ return uart_suspend_port(&amba_reg, &uap->port);
+}
+
+static int pl011_resume(struct amba_device *dev)
+{
+ struct uart_amba_port *uap = amba_get_drvdata(dev);
+
+ if (!uap)
+ return -EINVAL;
+
+ return uart_resume_port(&amba_reg, &uap->port);
+}
+#endif
+
+static struct amba_id pl011_ids[] = {
+ {
+ .id = 0x00041011,
+ .mask = 0x000fffff,
+ .data = &vendor_arm,
+ },
+ {
+ .id = 0x00380802,
+ .mask = 0x00ffffff,
+ .data = &vendor_st,
+ },
+ { 0, 0 },
+};
+
+static struct amba_driver pl011_driver = {
+ .drv = {
+ .name = "uart-pl011",
+ },
+ .id_table = pl011_ids,
+ .probe = pl011_probe,
+ .remove = pl011_remove,
+#ifdef CONFIG_PM
+ .suspend = pl011_suspend,
+ .resume = pl011_resume,
+#endif
+};
+
+static int __init pl011_init(void)
+{
+ int ret;
+ printk(KERN_INFO "Serial: AMBA PL011 UART driver\n");
+
+ ret = uart_register_driver(&amba_reg);
+ if (ret == 0) {
+ ret = amba_driver_register(&pl011_driver);
+ if (ret)
+ uart_unregister_driver(&amba_reg);
+ }
+ return ret;
+}
+
+static void __exit pl011_exit(void)
+{
+ amba_driver_unregister(&pl011_driver);
+ uart_unregister_driver(&amba_reg);
+}
+
+/*
+ * While this can be a module, if builtin it's most likely the console
+ * So let's leave module_exit but move module_init to an earlier place
+ */
+arch_initcall(pl011_init);
+module_exit(pl011_exit);
+
+MODULE_AUTHOR("ARM Ltd/Deep Blue Solutions Ltd");
+MODULE_DESCRIPTION("ARM AMBA serial port driver");
+MODULE_LICENSE("GPL");
git.openpandora.org / pandora-kernel.git / blobdiff