*
* SuperH on-chip serial module support. (SCI with no FIFO / with FIFO)
*
- * Copyright (C) 2002 - 2008 Paul Mundt
+ * Copyright (C) 2002 - 2011 Paul Mundt
* Modified to support SH7720 SCIF. Markus Brunner, Mark Jonas (Jul 2007).
*
* based off of the old drivers/char/sh-sci.c by:
#include <linux/ctype.h>
#include <linux/err.h>
#include <linux/list.h>
+#include <linux/dmaengine.h>
+#include <linux/scatterlist.h>
+#include <linux/slab.h>
#ifdef CONFIG_SUPERH
-#include <asm/clock.h>
#include <asm/sh_bios.h>
#endif
/* SCBRR calculation algo */
unsigned int scbrr_algo_id;
-#ifdef CONFIG_HAVE_CLK
/* Interface clock */
struct clk *iclk;
- /* Data clock */
- struct clk *dclk;
-#endif
+ /* Function clock */
+ struct clk *fclk;
+
struct list_head node;
+
+ struct dma_chan *chan_tx;
+ struct dma_chan *chan_rx;
+
+#ifdef CONFIG_SERIAL_SH_SCI_DMA
+ struct device *dma_dev;
+ unsigned int slave_tx;
+ unsigned int slave_rx;
+ struct dma_async_tx_descriptor *desc_tx;
+ struct dma_async_tx_descriptor *desc_rx[2];
+ dma_cookie_t cookie_tx;
+ dma_cookie_t cookie_rx[2];
+ dma_cookie_t active_rx;
+ struct scatterlist sg_tx;
+ unsigned int sg_len_tx;
+ struct scatterlist sg_rx[2];
+ size_t buf_len_rx;
+ struct sh_dmae_slave param_tx;
+ struct sh_dmae_slave param_rx;
+ struct work_struct work_tx;
+ struct work_struct work_rx;
+ struct timer_list rx_timer;
+ unsigned int rx_timeout;
+#endif
};
struct sh_sci_priv {
spinlock_t lock;
struct list_head ports;
-
-#ifdef CONFIG_HAVE_CLK
struct notifier_block clk_nb;
-#endif
};
/* Function prototypes */
handle_error(port);
continue;
}
- } while (!(status & SCxSR_RDxF(port)));
+ break;
+ } while (1);
+
+ if (!(status & SCxSR_RDxF(port)))
+ return NO_POLL_CHAR;
c = sci_in(port, SCxRDR);
}
#endif /* CONFIG_CONSOLE_POLL || CONFIG_SERIAL_SH_SCI_CONSOLE */
-#if defined(__H8300S__)
-enum { sci_disable, sci_enable };
-
-static void h8300_sci_config(struct uart_port *port, unsigned int ctrl)
-{
- volatile unsigned char *mstpcrl = (volatile unsigned char *)MSTPCRL;
- int ch = (port->mapbase - SMR0) >> 3;
- unsigned char mask = 1 << (ch+1);
-
- if (ctrl == sci_disable)
- *mstpcrl |= mask;
- else
- *mstpcrl &= ~mask;
-}
-
-static void h8300_sci_enable(struct uart_port *port)
-{
- h8300_sci_config(port, sci_enable);
-}
-
-static void h8300_sci_disable(struct uart_port *port)
-{
- h8300_sci_config(port, sci_disable);
-}
-#endif
-
#if defined(__H8300H__) || defined(__H8300S__)
static void sci_init_pins(struct uart_port *port, unsigned int cflag)
{
Set SCP6MD1,0 = {01} (output) */
__raw_writew((data & 0x0fcf) | 0x1000, SCPCR);
- data = ctrl_inb(SCPDR);
+ data = __raw_readb(SCPDR);
/* Set /RTS2 (bit6) = 0 */
- ctrl_outb(data & 0xbf, SCPDR);
+ __raw_writeb(data & 0xbf, SCPDR);
}
}
#elif defined(CONFIG_CPU_SUBTYPE_SH7722)
__raw_writew(data, PSCR);
}
}
-#elif defined(CONFIG_CPU_SUBTYPE_SH7763) || \
+#elif defined(CONFIG_CPU_SUBTYPE_SH7757) || \
+ defined(CONFIG_CPU_SUBTYPE_SH7763) || \
defined(CONFIG_CPU_SUBTYPE_SH7780) || \
defined(CONFIG_CPU_SUBTYPE_SH7785) || \
defined(CONFIG_CPU_SUBTYPE_SH7786) || \
defined(CONFIG_CPU_SUBTYPE_SH7780) || \
defined(CONFIG_CPU_SUBTYPE_SH7785) || \
defined(CONFIG_CPU_SUBTYPE_SH7786)
-static inline int scif_txroom(struct uart_port *port)
+static int scif_txfill(struct uart_port *port)
+{
+ return sci_in(port, SCTFDR) & 0xff;
+}
+
+static int scif_txroom(struct uart_port *port)
{
- return SCIF_TXROOM_MAX - (sci_in(port, SCTFDR) & 0xff);
+ return SCIF_TXROOM_MAX - scif_txfill(port);
}
-static inline int scif_rxroom(struct uart_port *port)
+static int scif_rxfill(struct uart_port *port)
{
return sci_in(port, SCRFDR) & 0xff;
}
#elif defined(CONFIG_CPU_SUBTYPE_SH7763)
-static inline int scif_txroom(struct uart_port *port)
+static int scif_txfill(struct uart_port *port)
{
- if ((port->mapbase == 0xffe00000) ||
- (port->mapbase == 0xffe08000)) {
+ if (port->mapbase == 0xffe00000 ||
+ port->mapbase == 0xffe08000)
/* SCIF0/1*/
- return SCIF_TXROOM_MAX - (sci_in(port, SCTFDR) & 0xff);
- } else {
+ return sci_in(port, SCTFDR) & 0xff;
+ else
/* SCIF2 */
- return SCIF2_TXROOM_MAX - (sci_in(port, SCFDR) >> 8);
- }
+ return sci_in(port, SCFDR) >> 8;
}
-static inline int scif_rxroom(struct uart_port *port)
+static int scif_txroom(struct uart_port *port)
+{
+ if (port->mapbase == 0xffe00000 ||
+ port->mapbase == 0xffe08000)
+ /* SCIF0/1*/
+ return SCIF_TXROOM_MAX - scif_txfill(port);
+ else
+ /* SCIF2 */
+ return SCIF2_TXROOM_MAX - scif_txfill(port);
+}
+
+static int scif_rxfill(struct uart_port *port)
{
if ((port->mapbase == 0xffe00000) ||
(port->mapbase == 0xffe08000)) {
return sci_in(port, SCFDR) & SCIF2_RFDC_MASK;
}
}
+#elif defined(CONFIG_ARCH_SH7372)
+static int scif_txfill(struct uart_port *port)
+{
+ if (port->type == PORT_SCIFA)
+ return sci_in(port, SCFDR) >> 8;
+ else
+ return sci_in(port, SCTFDR);
+}
+
+static int scif_txroom(struct uart_port *port)
+{
+ return port->fifosize - scif_txfill(port);
+}
+
+static int scif_rxfill(struct uart_port *port)
+{
+ if (port->type == PORT_SCIFA)
+ return sci_in(port, SCFDR) & SCIF_RFDC_MASK;
+ else
+ return sci_in(port, SCRFDR);
+}
#else
-static inline int scif_txroom(struct uart_port *port)
+static int scif_txfill(struct uart_port *port)
+{
+ return sci_in(port, SCFDR) >> 8;
+}
+
+static int scif_txroom(struct uart_port *port)
{
- return SCIF_TXROOM_MAX - (sci_in(port, SCFDR) >> 8);
+ return SCIF_TXROOM_MAX - scif_txfill(port);
}
-static inline int scif_rxroom(struct uart_port *port)
+static int scif_rxfill(struct uart_port *port)
{
return sci_in(port, SCFDR) & SCIF_RFDC_MASK;
}
#endif
-static inline int sci_txroom(struct uart_port *port)
+static int sci_txfill(struct uart_port *port)
{
- return (sci_in(port, SCxSR) & SCI_TDRE) != 0;
+ return !(sci_in(port, SCxSR) & SCI_TDRE);
}
-static inline int sci_rxroom(struct uart_port *port)
+static int sci_txroom(struct uart_port *port)
+{
+ return !sci_txfill(port);
+}
+
+static int sci_rxfill(struct uart_port *port)
{
return (sci_in(port, SCxSR) & SCxSR_RDxF(port)) != 0;
}
static void sci_transmit_chars(struct uart_port *port)
{
- struct circ_buf *xmit = &port->info->xmit;
+ struct circ_buf *xmit = &port->state->xmit;
unsigned int stopped = uart_tx_stopped(port);
unsigned short status;
unsigned short ctrl;
static inline void sci_receive_chars(struct uart_port *port)
{
struct sci_port *sci_port = to_sci_port(port);
- struct tty_struct *tty = port->info->port.tty;
+ struct tty_struct *tty = port->state->port.tty;
int i, count, copied = 0;
unsigned short status;
unsigned char flag;
while (1) {
if (port->type == PORT_SCI)
- count = sci_rxroom(port);
+ count = sci_rxfill(port);
else
- count = scif_rxroom(port);
+ count = scif_rxfill(port);
/* Don't copy more bytes than there is room for in the buffer */
count = tty_buffer_request_room(tty, count);
}
/* Store data and status */
- if (status&SCxSR_FER(port)) {
+ if (status & SCxSR_FER(port)) {
flag = TTY_FRAME;
dev_notice(port->dev, "frame error\n");
- } else if (status&SCxSR_PER(port)) {
+ } else if (status & SCxSR_PER(port)) {
flag = TTY_PARITY;
dev_notice(port->dev, "parity error\n");
} else
{
int copied = 0;
unsigned short status = sci_in(port, SCxSR);
- struct tty_struct *tty = port->info->port.tty;
+ struct tty_struct *tty = port->state->port.tty;
if (status & SCxSR_ORER(port)) {
/* overrun error */
static inline int sci_handle_fifo_overrun(struct uart_port *port)
{
- struct tty_struct *tty = port->info->port.tty;
+ struct tty_struct *tty = port->state->port.tty;
int copied = 0;
if (port->type != PORT_SCIF)
{
int copied = 0;
unsigned short status = sci_in(port, SCxSR);
- struct tty_struct *tty = port->info->port.tty;
+ struct tty_struct *tty = port->state->port.tty;
struct sci_port *s = to_sci_port(port);
if (uart_handle_break(port))
return copied;
}
-static irqreturn_t sci_rx_interrupt(int irq, void *port)
+static irqreturn_t sci_rx_interrupt(int irq, void *ptr)
{
+#ifdef CONFIG_SERIAL_SH_SCI_DMA
+ struct uart_port *port = ptr;
+ struct sci_port *s = to_sci_port(port);
+
+ if (s->chan_rx) {
+ u16 scr = sci_in(port, SCSCR);
+ u16 ssr = sci_in(port, SCxSR);
+
+ /* Disable future Rx interrupts */
+ if (port->type == PORT_SCIFA || port->type == PORT_SCIFB) {
+ disable_irq_nosync(irq);
+ scr |= 0x4000;
+ } else {
+ scr &= ~SCSCR_RIE;
+ }
+ sci_out(port, SCSCR, scr);
+ /* Clear current interrupt */
+ sci_out(port, SCxSR, ssr & ~(1 | SCxSR_RDxF(port)));
+ dev_dbg(port->dev, "Rx IRQ %lu: setup t-out in %u jiffies\n",
+ jiffies, s->rx_timeout);
+ mod_timer(&s->rx_timer, jiffies + s->rx_timeout);
+
+ return IRQ_HANDLED;
+ }
+#endif
+
/* I think sci_receive_chars has to be called irrespective
* of whether the I_IXOFF is set, otherwise, how is the interrupt
* to be disabled?
*/
- sci_receive_chars(port);
+ sci_receive_chars(ptr);
return IRQ_HANDLED;
}
static irqreturn_t sci_tx_interrupt(int irq, void *ptr)
{
struct uart_port *port = ptr;
+ unsigned long flags;
- spin_lock_irq(&port->lock);
+ spin_lock_irqsave(&port->lock, flags);
sci_transmit_chars(port);
- spin_unlock_irq(&port->lock);
+ spin_unlock_irqrestore(&port->lock, flags);
return IRQ_HANDLED;
}
return IRQ_HANDLED;
}
+static inline unsigned long port_rx_irq_mask(struct uart_port *port)
+{
+ /*
+ * Not all ports (such as SCIFA) will support REIE. Rather than
+ * special-casing the port type, we check the port initialization
+ * IRQ enable mask to see whether the IRQ is desired at all. If
+ * it's unset, it's logically inferred that there's no point in
+ * testing for it.
+ */
+ return SCSCR_RIE | (to_sci_port(port)->scscr & SCSR_REIE);
+}
+
static irqreturn_t sci_mpxed_interrupt(int irq, void *ptr)
{
- unsigned short ssr_status, scr_status;
+ unsigned short ssr_status, scr_status, err_enabled;
struct uart_port *port = ptr;
+ struct sci_port *s = to_sci_port(port);
irqreturn_t ret = IRQ_NONE;
ssr_status = sci_in(port, SCxSR);
scr_status = sci_in(port, SCSCR);
+ err_enabled = scr_status & port_rx_irq_mask(port);
/* Tx Interrupt */
- if ((ssr_status & 0x0020) && (scr_status & SCSCR_TIE))
+ if ((ssr_status & SCxSR_TDxE(port)) && (scr_status & SCSCR_TIE) &&
+ !s->chan_tx)
ret = sci_tx_interrupt(irq, ptr);
- /* Rx Interrupt */
- if ((ssr_status & 0x0002) && (scr_status & SCSCR_RIE))
+
+ /*
+ * Rx Interrupt: if we're using DMA, the DMA controller clears RDF /
+ * DR flags
+ */
+ if (((ssr_status & SCxSR_RDxF(port)) || s->chan_rx) &&
+ (scr_status & SCSCR_RIE))
ret = sci_rx_interrupt(irq, ptr);
+
/* Error Interrupt */
- if ((ssr_status & 0x0080) && (scr_status & SCSCR_REIE))
+ if ((ssr_status & SCxSR_ERRORS(port)) && err_enabled)
ret = sci_er_interrupt(irq, ptr);
+
/* Break Interrupt */
- if ((ssr_status & 0x0010) && (scr_status & SCSCR_REIE))
+ if ((ssr_status & SCxSR_BRK(port)) && err_enabled)
ret = sci_br_interrupt(irq, ptr);
return ret;
}
-#ifdef CONFIG_HAVE_CLK
/*
* Here we define a transistion notifier so that we can update all of our
* ports' baud rate when the peripheral clock changes.
(phase == CPUFREQ_RESUMECHANGE)) {
spin_lock_irqsave(&priv->lock, flags);
list_for_each_entry(sci_port, &priv->ports, node)
- sci_port->port.uartclk = clk_get_rate(sci_port->dclk);
-
+ sci_port->port.uartclk = clk_get_rate(sci_port->iclk);
spin_unlock_irqrestore(&priv->lock, flags);
}
{
struct sci_port *sci_port = to_sci_port(port);
- clk_enable(sci_port->dclk);
- sci_port->port.uartclk = clk_get_rate(sci_port->dclk);
-
- if (sci_port->iclk)
- clk_enable(sci_port->iclk);
+ clk_enable(sci_port->iclk);
+ sci_port->port.uartclk = clk_get_rate(sci_port->iclk);
+ clk_enable(sci_port->fclk);
}
static void sci_clk_disable(struct uart_port *port)
{
struct sci_port *sci_port = to_sci_port(port);
- if (sci_port->iclk)
- clk_disable(sci_port->iclk);
-
- clk_disable(sci_port->dclk);
+ clk_disable(sci_port->fclk);
+ clk_disable(sci_port->iclk);
}
-#endif
static int sci_request_irq(struct sci_port *port)
{
static unsigned int sci_tx_empty(struct uart_port *port)
{
- /* Can't detect */
- return TIOCSER_TEMT;
+ unsigned short status = sci_in(port, SCxSR);
+ unsigned short in_tx_fifo = scif_txfill(port);
+
+ return (status & SCxSR_TEND(port)) && !in_tx_fifo ? TIOCSER_TEMT : 0;
}
static void sci_set_mctrl(struct uart_port *port, unsigned int mctrl)
static unsigned int sci_get_mctrl(struct uart_port *port)
{
- /* This routine is used for geting signals of: DTR, DCD, DSR, RI,
+ /* This routine is used for getting signals of: DTR, DCD, DSR, RI,
and CTS/RTS */
return TIOCM_DTR | TIOCM_RTS | TIOCM_DSR;
}
+#ifdef CONFIG_SERIAL_SH_SCI_DMA
+static void sci_dma_tx_complete(void *arg)
+{
+ struct sci_port *s = arg;
+ struct uart_port *port = &s->port;
+ struct circ_buf *xmit = &port->state->xmit;
+ unsigned long flags;
+
+ dev_dbg(port->dev, "%s(%d)\n", __func__, port->line);
+
+ spin_lock_irqsave(&port->lock, flags);
+
+ xmit->tail += sg_dma_len(&s->sg_tx);
+ xmit->tail &= UART_XMIT_SIZE - 1;
+
+ port->icount.tx += sg_dma_len(&s->sg_tx);
+
+ async_tx_ack(s->desc_tx);
+ s->cookie_tx = -EINVAL;
+ s->desc_tx = NULL;
+
+ if (uart_circ_chars_pending(xmit) < WAKEUP_CHARS)
+ uart_write_wakeup(port);
+
+ if (!uart_circ_empty(xmit)) {
+ schedule_work(&s->work_tx);
+ } else if (port->type == PORT_SCIFA || port->type == PORT_SCIFB) {
+ u16 ctrl = sci_in(port, SCSCR);
+ sci_out(port, SCSCR, ctrl & ~SCSCR_TIE);
+ }
+
+ spin_unlock_irqrestore(&port->lock, flags);
+}
+
+/* Locking: called with port lock held */
+static int sci_dma_rx_push(struct sci_port *s, struct tty_struct *tty,
+ size_t count)
+{
+ struct uart_port *port = &s->port;
+ int i, active, room;
+
+ room = tty_buffer_request_room(tty, count);
+
+ if (s->active_rx == s->cookie_rx[0]) {
+ active = 0;
+ } else if (s->active_rx == s->cookie_rx[1]) {
+ active = 1;
+ } else {
+ dev_err(port->dev, "cookie %d not found!\n", s->active_rx);
+ return 0;
+ }
+
+ if (room < count)
+ dev_warn(port->dev, "Rx overrun: dropping %u bytes\n",
+ count - room);
+ if (!room)
+ return room;
+
+ for (i = 0; i < room; i++)
+ tty_insert_flip_char(tty, ((u8 *)sg_virt(&s->sg_rx[active]))[i],
+ TTY_NORMAL);
+
+ port->icount.rx += room;
+
+ return room;
+}
+
+static void sci_dma_rx_complete(void *arg)
+{
+ struct sci_port *s = arg;
+ struct uart_port *port = &s->port;
+ struct tty_struct *tty = port->state->port.tty;
+ unsigned long flags;
+ int count;
+
+ dev_dbg(port->dev, "%s(%d) active #%d\n", __func__, port->line, s->active_rx);
+
+ spin_lock_irqsave(&port->lock, flags);
+
+ count = sci_dma_rx_push(s, tty, s->buf_len_rx);
+
+ mod_timer(&s->rx_timer, jiffies + s->rx_timeout);
+
+ spin_unlock_irqrestore(&port->lock, flags);
+
+ if (count)
+ tty_flip_buffer_push(tty);
+
+ schedule_work(&s->work_rx);
+}
+
+static void sci_start_rx(struct uart_port *port);
+static void sci_start_tx(struct uart_port *port);
+
+static void sci_rx_dma_release(struct sci_port *s, bool enable_pio)
+{
+ struct dma_chan *chan = s->chan_rx;
+ struct uart_port *port = &s->port;
+
+ s->chan_rx = NULL;
+ s->cookie_rx[0] = s->cookie_rx[1] = -EINVAL;
+ dma_release_channel(chan);
+ if (sg_dma_address(&s->sg_rx[0]))
+ dma_free_coherent(port->dev, s->buf_len_rx * 2,
+ sg_virt(&s->sg_rx[0]), sg_dma_address(&s->sg_rx[0]));
+ if (enable_pio)
+ sci_start_rx(port);
+}
+
+static void sci_tx_dma_release(struct sci_port *s, bool enable_pio)
+{
+ struct dma_chan *chan = s->chan_tx;
+ struct uart_port *port = &s->port;
+
+ s->chan_tx = NULL;
+ s->cookie_tx = -EINVAL;
+ dma_release_channel(chan);
+ if (enable_pio)
+ sci_start_tx(port);
+}
+
+static void sci_submit_rx(struct sci_port *s)
+{
+ struct dma_chan *chan = s->chan_rx;
+ int i;
+
+ for (i = 0; i < 2; i++) {
+ struct scatterlist *sg = &s->sg_rx[i];
+ struct dma_async_tx_descriptor *desc;
+
+ desc = chan->device->device_prep_slave_sg(chan,
+ sg, 1, DMA_FROM_DEVICE, DMA_PREP_INTERRUPT);
+
+ if (desc) {
+ s->desc_rx[i] = desc;
+ desc->callback = sci_dma_rx_complete;
+ desc->callback_param = s;
+ s->cookie_rx[i] = desc->tx_submit(desc);
+ }
+
+ if (!desc || s->cookie_rx[i] < 0) {
+ if (i) {
+ async_tx_ack(s->desc_rx[0]);
+ s->cookie_rx[0] = -EINVAL;
+ }
+ if (desc) {
+ async_tx_ack(desc);
+ s->cookie_rx[i] = -EINVAL;
+ }
+ dev_warn(s->port.dev,
+ "failed to re-start DMA, using PIO\n");
+ sci_rx_dma_release(s, true);
+ return;
+ }
+ dev_dbg(s->port.dev, "%s(): cookie %d to #%d\n", __func__,
+ s->cookie_rx[i], i);
+ }
+
+ s->active_rx = s->cookie_rx[0];
+
+ dma_async_issue_pending(chan);
+}
+
+static void work_fn_rx(struct work_struct *work)
+{
+ struct sci_port *s = container_of(work, struct sci_port, work_rx);
+ struct uart_port *port = &s->port;
+ struct dma_async_tx_descriptor *desc;
+ int new;
+
+ if (s->active_rx == s->cookie_rx[0]) {
+ new = 0;
+ } else if (s->active_rx == s->cookie_rx[1]) {
+ new = 1;
+ } else {
+ dev_err(port->dev, "cookie %d not found!\n", s->active_rx);
+ return;
+ }
+ desc = s->desc_rx[new];
+
+ if (dma_async_is_tx_complete(s->chan_rx, s->active_rx, NULL, NULL) !=
+ DMA_SUCCESS) {
+ /* Handle incomplete DMA receive */
+ struct tty_struct *tty = port->state->port.tty;
+ struct dma_chan *chan = s->chan_rx;
+ struct sh_desc *sh_desc = container_of(desc, struct sh_desc,
+ async_tx);
+ unsigned long flags;
+ int count;
+
+ chan->device->device_control(chan, DMA_TERMINATE_ALL, 0);
+ dev_dbg(port->dev, "Read %u bytes with cookie %d\n",
+ sh_desc->partial, sh_desc->cookie);
+
+ spin_lock_irqsave(&port->lock, flags);
+ count = sci_dma_rx_push(s, tty, sh_desc->partial);
+ spin_unlock_irqrestore(&port->lock, flags);
+
+ if (count)
+ tty_flip_buffer_push(tty);
+
+ sci_submit_rx(s);
+
+ return;
+ }
+
+ s->cookie_rx[new] = desc->tx_submit(desc);
+ if (s->cookie_rx[new] < 0) {
+ dev_warn(port->dev, "Failed submitting Rx DMA descriptor\n");
+ sci_rx_dma_release(s, true);
+ return;
+ }
+
+ s->active_rx = s->cookie_rx[!new];
+
+ dev_dbg(port->dev, "%s: cookie %d #%d, new active #%d\n", __func__,
+ s->cookie_rx[new], new, s->active_rx);
+}
+
+static void work_fn_tx(struct work_struct *work)
+{
+ struct sci_port *s = container_of(work, struct sci_port, work_tx);
+ struct dma_async_tx_descriptor *desc;
+ struct dma_chan *chan = s->chan_tx;
+ struct uart_port *port = &s->port;
+ struct circ_buf *xmit = &port->state->xmit;
+ struct scatterlist *sg = &s->sg_tx;
+
+ /*
+ * DMA is idle now.
+ * Port xmit buffer is already mapped, and it is one page... Just adjust
+ * offsets and lengths. Since it is a circular buffer, we have to
+ * transmit till the end, and then the rest. Take the port lock to get a
+ * consistent xmit buffer state.
+ */
+ spin_lock_irq(&port->lock);
+ sg->offset = xmit->tail & (UART_XMIT_SIZE - 1);
+ sg_dma_address(sg) = (sg_dma_address(sg) & ~(UART_XMIT_SIZE - 1)) +
+ sg->offset;
+ sg_dma_len(sg) = min((int)CIRC_CNT(xmit->head, xmit->tail, UART_XMIT_SIZE),
+ CIRC_CNT_TO_END(xmit->head, xmit->tail, UART_XMIT_SIZE));
+ spin_unlock_irq(&port->lock);
+
+ BUG_ON(!sg_dma_len(sg));
+
+ desc = chan->device->device_prep_slave_sg(chan,
+ sg, s->sg_len_tx, DMA_TO_DEVICE,
+ DMA_PREP_INTERRUPT | DMA_CTRL_ACK);
+ if (!desc) {
+ /* switch to PIO */
+ sci_tx_dma_release(s, true);
+ return;
+ }
+
+ dma_sync_sg_for_device(port->dev, sg, 1, DMA_TO_DEVICE);
+
+ spin_lock_irq(&port->lock);
+ s->desc_tx = desc;
+ desc->callback = sci_dma_tx_complete;
+ desc->callback_param = s;
+ spin_unlock_irq(&port->lock);
+ s->cookie_tx = desc->tx_submit(desc);
+ if (s->cookie_tx < 0) {
+ dev_warn(port->dev, "Failed submitting Tx DMA descriptor\n");
+ /* switch to PIO */
+ sci_tx_dma_release(s, true);
+ return;
+ }
+
+ dev_dbg(port->dev, "%s: %p: %d...%d, cookie %d\n", __func__,
+ xmit->buf, xmit->tail, xmit->head, s->cookie_tx);
+
+ dma_async_issue_pending(chan);
+}
+#endif
+
static void sci_start_tx(struct uart_port *port)
{
+ struct sci_port *s = to_sci_port(port);
unsigned short ctrl;
- /* Set TIE (Transmit Interrupt Enable) bit in SCSCR */
- ctrl = sci_in(port, SCSCR);
- ctrl |= SCSCR_TIE;
- sci_out(port, SCSCR, ctrl);
+#ifdef CONFIG_SERIAL_SH_SCI_DMA
+ if (port->type == PORT_SCIFA || port->type == PORT_SCIFB) {
+ u16 new, scr = sci_in(port, SCSCR);
+ if (s->chan_tx)
+ new = scr | 0x8000;
+ else
+ new = scr & ~0x8000;
+ if (new != scr)
+ sci_out(port, SCSCR, new);
+ }
+
+ if (s->chan_tx && !uart_circ_empty(&s->port.state->xmit) &&
+ s->cookie_tx < 0)
+ schedule_work(&s->work_tx);
+#endif
+
+ if (!s->chan_tx || port->type == PORT_SCIFA || port->type == PORT_SCIFB) {
+ /* Set TIE (Transmit Interrupt Enable) bit in SCSCR */
+ ctrl = sci_in(port, SCSCR);
+ sci_out(port, SCSCR, ctrl | SCSCR_TIE);
+ }
}
static void sci_stop_tx(struct uart_port *port)
/* Clear TIE (Transmit Interrupt Enable) bit in SCSCR */
ctrl = sci_in(port, SCSCR);
+
+ if (port->type == PORT_SCIFA || port->type == PORT_SCIFB)
+ ctrl &= ~0x8000;
+
ctrl &= ~SCSCR_TIE;
+
sci_out(port, SCSCR, ctrl);
}
-static void sci_start_rx(struct uart_port *port, unsigned int tty_start)
+static void sci_start_rx(struct uart_port *port)
{
unsigned short ctrl;
- /* Set RIE (Receive Interrupt Enable) bit in SCSCR */
- ctrl = sci_in(port, SCSCR);
- ctrl |= SCSCR_RIE | SCSCR_REIE;
+ ctrl = sci_in(port, SCSCR) | port_rx_irq_mask(port);
+
+ if (port->type == PORT_SCIFA || port->type == PORT_SCIFB)
+ ctrl &= ~0x4000;
+
sci_out(port, SCSCR, ctrl);
}
{
unsigned short ctrl;
- /* Clear RIE (Receive Interrupt Enable) bit in SCSCR */
ctrl = sci_in(port, SCSCR);
- ctrl &= ~(SCSCR_RIE | SCSCR_REIE);
+
+ if (port->type == PORT_SCIFA || port->type == PORT_SCIFB)
+ ctrl &= ~0x4000;
+
+ ctrl &= ~port_rx_irq_mask(port);
+
sci_out(port, SCSCR, ctrl);
}
/* Nothing here yet .. */
}
+#ifdef CONFIG_SERIAL_SH_SCI_DMA
+static bool filter(struct dma_chan *chan, void *slave)
+{
+ struct sh_dmae_slave *param = slave;
+
+ dev_dbg(chan->device->dev, "%s: slave ID %d\n", __func__,
+ param->slave_id);
+
+ if (param->dma_dev == chan->device->dev) {
+ chan->private = param;
+ return true;
+ } else {
+ return false;
+ }
+}
+
+static void rx_timer_fn(unsigned long arg)
+{
+ struct sci_port *s = (struct sci_port *)arg;
+ struct uart_port *port = &s->port;
+ u16 scr = sci_in(port, SCSCR);
+
+ if (port->type == PORT_SCIFA || port->type == PORT_SCIFB) {
+ scr &= ~0x4000;
+ enable_irq(s->irqs[1]);
+ }
+ sci_out(port, SCSCR, scr | SCSCR_RIE);
+ dev_dbg(port->dev, "DMA Rx timed out\n");
+ schedule_work(&s->work_rx);
+}
+
+static void sci_request_dma(struct uart_port *port)
+{
+ struct sci_port *s = to_sci_port(port);
+ struct sh_dmae_slave *param;
+ struct dma_chan *chan;
+ dma_cap_mask_t mask;
+ int nent;
+
+ dev_dbg(port->dev, "%s: port %d DMA %p\n", __func__,
+ port->line, s->dma_dev);
+
+ if (!s->dma_dev)
+ return;
+
+ dma_cap_zero(mask);
+ dma_cap_set(DMA_SLAVE, mask);
+
+ param = &s->param_tx;
+
+ /* Slave ID, e.g., SHDMA_SLAVE_SCIF0_TX */
+ param->slave_id = s->slave_tx;
+ param->dma_dev = s->dma_dev;
+
+ s->cookie_tx = -EINVAL;
+ chan = dma_request_channel(mask, filter, param);
+ dev_dbg(port->dev, "%s: TX: got channel %p\n", __func__, chan);
+ if (chan) {
+ s->chan_tx = chan;
+ sg_init_table(&s->sg_tx, 1);
+ /* UART circular tx buffer is an aligned page. */
+ BUG_ON((int)port->state->xmit.buf & ~PAGE_MASK);
+ sg_set_page(&s->sg_tx, virt_to_page(port->state->xmit.buf),
+ UART_XMIT_SIZE, (int)port->state->xmit.buf & ~PAGE_MASK);
+ nent = dma_map_sg(port->dev, &s->sg_tx, 1, DMA_TO_DEVICE);
+ if (!nent)
+ sci_tx_dma_release(s, false);
+ else
+ dev_dbg(port->dev, "%s: mapped %d@%p to %x\n", __func__,
+ sg_dma_len(&s->sg_tx),
+ port->state->xmit.buf, sg_dma_address(&s->sg_tx));
+
+ s->sg_len_tx = nent;
+
+ INIT_WORK(&s->work_tx, work_fn_tx);
+ }
+
+ param = &s->param_rx;
+
+ /* Slave ID, e.g., SHDMA_SLAVE_SCIF0_RX */
+ param->slave_id = s->slave_rx;
+ param->dma_dev = s->dma_dev;
+
+ chan = dma_request_channel(mask, filter, param);
+ dev_dbg(port->dev, "%s: RX: got channel %p\n", __func__, chan);
+ if (chan) {
+ dma_addr_t dma[2];
+ void *buf[2];
+ int i;
+
+ s->chan_rx = chan;
+
+ s->buf_len_rx = 2 * max(16, (int)port->fifosize);
+ buf[0] = dma_alloc_coherent(port->dev, s->buf_len_rx * 2,
+ &dma[0], GFP_KERNEL);
+
+ if (!buf[0]) {
+ dev_warn(port->dev,
+ "failed to allocate dma buffer, using PIO\n");
+ sci_rx_dma_release(s, true);
+ return;
+ }
+
+ buf[1] = buf[0] + s->buf_len_rx;
+ dma[1] = dma[0] + s->buf_len_rx;
+
+ for (i = 0; i < 2; i++) {
+ struct scatterlist *sg = &s->sg_rx[i];
+
+ sg_init_table(sg, 1);
+ sg_set_page(sg, virt_to_page(buf[i]), s->buf_len_rx,
+ (int)buf[i] & ~PAGE_MASK);
+ sg_dma_address(sg) = dma[i];
+ }
+
+ INIT_WORK(&s->work_rx, work_fn_rx);
+ setup_timer(&s->rx_timer, rx_timer_fn, (unsigned long)s);
+
+ sci_submit_rx(s);
+ }
+}
+
+static void sci_free_dma(struct uart_port *port)
+{
+ struct sci_port *s = to_sci_port(port);
+
+ if (!s->dma_dev)
+ return;
+
+ if (s->chan_tx)
+ sci_tx_dma_release(s, false);
+ if (s->chan_rx)
+ sci_rx_dma_release(s, false);
+}
+#endif
+
static int sci_startup(struct uart_port *port)
{
struct sci_port *s = to_sci_port(port);
+ dev_dbg(port->dev, "%s(%d)\n", __func__, port->line);
+
if (s->enable)
s->enable(port);
sci_request_irq(s);
+#ifdef CONFIG_SERIAL_SH_SCI_DMA
+ sci_request_dma(port);
+#endif
sci_start_tx(port);
- sci_start_rx(port, 1);
+ sci_start_rx(port);
return 0;
}
{
struct sci_port *s = to_sci_port(port);
+ dev_dbg(port->dev, "%s(%d)\n", __func__, port->line);
+
sci_stop_rx(port);
sci_stop_tx(port);
+#ifdef CONFIG_SERIAL_SH_SCI_DMA
+ sci_free_dma(port);
+#endif
sci_free_irq(s);
if (s->disable)
struct ktermios *old)
{
struct sci_port *s = to_sci_port(port);
- unsigned int status, baud, smr_val;
+ unsigned int status, baud, smr_val, max_baud;
int t = -1;
+ u16 scfcr = 0;
+
+ /*
+ * earlyprintk comes here early on with port->uartclk set to zero.
+ * the clock framework is not up and running at this point so here
+ * we assume that 115200 is the maximum baud rate. please note that
+ * the baud rate is not programmed during earlyprintk - it is assumed
+ * that the previous boot loader has enabled required clocks and
+ * setup the baud rate generator hardware for us already.
+ */
+ max_baud = port->uartclk ? port->uartclk / 16 : 115200;
- baud = uart_get_baud_rate(port, termios, old, 0, port->uartclk/16);
- if (likely(baud))
+ baud = uart_get_baud_rate(port, termios, old, 0, max_baud);
+ if (likely(baud && port->uartclk))
t = sci_scbrr_calc(s->scbrr_algo_id, baud, port->uartclk);
do {
sci_out(port, SCSCR, 0x00); /* TE=0, RE=0, CKE1=0 */
if (port->type != PORT_SCI)
- sci_out(port, SCFCR, SCFCR_RFRST | SCFCR_TFRST);
+ sci_out(port, SCFCR, scfcr | SCFCR_RFRST | SCFCR_TFRST);
smr_val = sci_in(port, SCSMR) & 3;
if ((termios->c_cflag & CSIZE) == CS7)
sci_out(port, SCSMR, smr_val);
+ dev_dbg(port->dev, "%s: SMR %x, t %x, SCSCR %x\n", __func__, smr_val, t,
+ SCSCR_INIT(port));
+
if (t > 0) {
if (t >= 256) {
sci_out(port, SCSMR, (sci_in(port, SCSMR) & ~3) | 1);
}
sci_init_pins(port, termios->c_cflag);
- sci_out(port, SCFCR, (termios->c_cflag & CRTSCTS) ? SCFCR_MCE : 0);
+ sci_out(port, SCFCR, scfcr | ((termios->c_cflag & CRTSCTS) ? SCFCR_MCE : 0));
sci_out(port, SCSCR, s->scscr);
+#ifdef CONFIG_SERIAL_SH_SCI_DMA
+ /*
+ * Calculate delay for 1.5 DMA buffers: see
+ * drivers/serial/serial_core.c::uart_update_timeout(). With 10 bits
+ * (CS8), 250Hz, 115200 baud and 64 bytes FIFO, the above function
+ * calculates 1 jiffie for the data plus 5 jiffies for the "slop(e)."
+ * Then below we calculate 3 jiffies (12ms) for 1.5 DMA buffers (3 FIFO
+ * sizes), but it has been found out experimentally, that this is not
+ * enough: the driver too often needlessly runs on a DMA timeout. 20ms
+ * as a minimum seem to work perfectly.
+ */
+ if (s->chan_rx) {
+ s->rx_timeout = (port->timeout - HZ / 50) * s->buf_len_rx * 3 /
+ port->fifosize / 2;
+ dev_dbg(port->dev,
+ "DMA Rx t-out %ums, tty t-out %u jiffies\n",
+ s->rx_timeout * 1000 / HZ, port->timeout);
+ if (s->rx_timeout < msecs_to_jiffies(20))
+ s->rx_timeout = msecs_to_jiffies(20);
+ }
+#endif
+
if ((termios->c_cflag & CREAD) != 0)
- sci_start_rx(port, 0);
+ sci_start_rx(port);
}
static const char *sci_type(struct uart_port *port)
return "scif";
case PORT_SCIFA:
return "scifa";
+ case PORT_SCIFB:
+ return "scifb";
}
return NULL;
#endif
};
-static void __devinit sci_init_single(struct platform_device *dev,
- struct sci_port *sci_port,
- unsigned int index,
- struct plat_sci_port *p)
+static int __devinit sci_init_single(struct platform_device *dev,
+ struct sci_port *sci_port,
+ unsigned int index,
+ struct plat_sci_port *p)
{
- sci_port->port.ops = &sci_uart_ops;
- sci_port->port.iotype = UPIO_MEM;
- sci_port->port.line = index;
- sci_port->port.fifosize = 1;
+ struct uart_port *port = &sci_port->port;
-#if defined(__H8300H__) || defined(__H8300S__)
-#ifdef __H8300S__
- sci_port->enable = h8300_sci_enable;
- sci_port->disable = h8300_sci_disable;
-#endif
- sci_port->port.uartclk = CONFIG_CPU_CLOCK;
-#elif defined(CONFIG_HAVE_CLK)
- sci_port->iclk = p->clk ? clk_get(&dev->dev, p->clk) : NULL;
- sci_port->dclk = clk_get(&dev->dev, "peripheral_clk");
- sci_port->enable = sci_clk_enable;
- sci_port->disable = sci_clk_disable;
-#else
-#error "Need a valid uartclk"
-#endif
+ port->ops = &sci_uart_ops;
+ port->iotype = UPIO_MEM;
+ port->line = index;
+
+ switch (p->type) {
+ case PORT_SCIFB:
+ port->fifosize = 256;
+ break;
+ case PORT_SCIFA:
+ port->fifosize = 64;
+ break;
+ case PORT_SCIF:
+ port->fifosize = 16;
+ break;
+ default:
+ port->fifosize = 1;
+ break;
+ }
+
+ if (dev) {
+ sci_port->iclk = clk_get(&dev->dev, "sci_ick");
+ if (IS_ERR(sci_port->iclk)) {
+ sci_port->iclk = clk_get(&dev->dev, "peripheral_clk");
+ if (IS_ERR(sci_port->iclk)) {
+ dev_err(&dev->dev, "can't get iclk\n");
+ return PTR_ERR(sci_port->iclk);
+ }
+ }
+
+ /*
+ * The function clock is optional, ignore it if we can't
+ * find it.
+ */
+ sci_port->fclk = clk_get(&dev->dev, "sci_fck");
+ if (IS_ERR(sci_port->fclk))
+ sci_port->fclk = NULL;
+
+ sci_port->enable = sci_clk_enable;
+ sci_port->disable = sci_clk_disable;
+ port->dev = &dev->dev;
+ }
sci_port->break_timer.data = (unsigned long)sci_port;
sci_port->break_timer.function = sci_break_timer;
init_timer(&sci_port->break_timer);
- sci_port->port.mapbase = p->mapbase;
- sci_port->port.membase = p->membase;
+ port->mapbase = p->mapbase;
+ port->membase = p->membase;
+ port->irq = p->irqs[SCIx_TXI_IRQ];
+ port->flags = p->flags;
+ sci_port->type = port->type = p->type;
sci_port->scscr = p->scscr;
- sci_port->port.irq = p->irqs[SCIx_TXI_IRQ];
- sci_port->port.flags = p->flags;
- sci_port->port.dev = &dev->dev;
- sci_port->type = sci_port->port.type = p->type;
+ sci_port->scbrr_algo_id = p->scbrr_algo_id;
+
+#ifdef CONFIG_SERIAL_SH_SCI_DMA
+ sci_port->dma_dev = p->dma_dev;
+ sci_port->slave_tx = p->dma_slave_tx;
+ sci_port->slave_rx = p->dma_slave_rx;
+
+ dev_dbg(port->dev, "%s: DMA device %p, tx %d, rx %d\n", __func__,
+ p->dma_dev, p->dma_slave_tx, p->dma_slave_rx);
+#endif
memcpy(&sci_port->irqs, &p->irqs, sizeof(p->irqs));
+ return 0;
}
#ifdef CONFIG_SERIAL_SH_SCI_CONSOLE
while ((sci_in(port, SCxSR) & bits) != bits)
cpu_relax();
- if (sci_port->disable);
+ if (sci_port->disable)
sci_port->disable(port);
}
-static int __init serial_console_setup(struct console *co, char *options)
+static int __devinit serial_console_setup(struct console *co, char *options)
{
struct sci_port *sci_port;
struct uart_port *port;
if (co->index >= SCI_NPORTS)
co->index = 0;
- sci_port = &sci_ports[co->index];
- port = &sci_port->port;
- co->data = port;
+ if (co->data) {
+ port = co->data;
+ sci_port = to_sci_port(port);
+ } else {
+ sci_port = &sci_ports[co->index];
+ port = &sci_port->port;
+ co->data = port;
+ }
/*
* Also need to check port->type, we don't actually have any
return 0;
}
console_initcall(sci_console_init);
+
+static struct sci_port early_serial_port;
+static struct console early_serial_console = {
+ .name = "early_ttySC",
+ .write = serial_console_write,
+ .flags = CON_PRINTBUFFER,
+};
+static char early_serial_buf[32];
+
#endif /* CONFIG_SERIAL_SH_SCI_CONSOLE */
#if defined(CONFIG_SERIAL_SH_SCI_CONSOLE)
struct sci_port *p;
unsigned long flags;
-#ifdef CONFIG_HAVE_CLK
cpufreq_unregister_notifier(&priv->clk_nb, CPUFREQ_TRANSITION_NOTIFIER);
-#endif
spin_lock_irqsave(&priv->lock, flags);
- list_for_each_entry(p, &priv->ports, node)
+ list_for_each_entry(p, &priv->ports, node) {
uart_remove_one_port(&sci_uart_driver, &p->port);
-
+ clk_put(p->iclk);
+ clk_put(p->fclk);
+ }
spin_unlock_irqrestore(&priv->lock, flags);
kfree(priv);
return 0;
}
- sci_init_single(dev, sciport, index, p);
+ ret = sci_init_single(dev, sciport, index, p);
+ if (ret)
+ return ret;
ret = uart_add_one_port(&sci_uart_driver, &sciport->port);
if (ret)
struct sh_sci_priv *priv;
int i, ret = -EINVAL;
+#ifdef CONFIG_SERIAL_SH_SCI_CONSOLE
+ if (is_early_platform_device(dev)) {
+ if (dev->id == -1)
+ return -ENOTSUPP;
+ early_serial_console.index = dev->id;
+ early_serial_console.data = &early_serial_port.port;
+ sci_init_single(NULL, &early_serial_port, dev->id, p);
+ serial_console_setup(&early_serial_console, early_serial_buf);
+ if (!strstr(early_serial_buf, "keep"))
+ early_serial_console.flags |= CON_BOOT;
+ register_console(&early_serial_console);
+ return 0;
+ }
+#endif
+
priv = kzalloc(sizeof(*priv), GFP_KERNEL);
if (!priv)
return -ENOMEM;
spin_lock_init(&priv->lock);
platform_set_drvdata(dev, priv);
-#ifdef CONFIG_HAVE_CLK
priv->clk_nb.notifier_call = sci_notifier;
cpufreq_register_notifier(&priv->clk_nb, CPUFREQ_TRANSITION_NOTIFIER);
-#endif
if (dev->id != -1) {
ret = sci_probe_single(dev, dev->id, p, &sci_ports[dev->id]);
return 0;
}
-static struct dev_pm_ops sci_dev_pm_ops = {
+static const struct dev_pm_ops sci_dev_pm_ops = {
.suspend = sci_suspend,
.resume = sci_resume,
};
static struct platform_driver sci_driver = {
.probe = sci_probe,
- .remove = __devexit_p(sci_remove),
+ .remove = sci_remove,
.driver = {
.name = "sh-sci",
.owner = THIS_MODULE,
uart_unregister_driver(&sci_uart_driver);
}
+#ifdef CONFIG_SERIAL_SH_SCI_CONSOLE
+early_platform_init_buffer("earlyprintk", &sci_driver,
+ early_serial_buf, ARRAY_SIZE(early_serial_buf));
+#endif
module_init(sci_init);
module_exit(sci_exit);
git.openpandora.org / pandora-kernel.git / blobdiff