};
#endif /* CONFIG_RT2X00_LIB_DEBUGFS */
-#ifdef CONFIG_RT2X00_LIB_RFKILL
static int rt2800usb_rfkill_poll(struct rt2x00_dev *rt2x00dev)
{
u32 reg;
rt2x00usb_register_read(rt2x00dev, GPIO_CTRL_CFG, ®);
return rt2x00_get_field32(reg, GPIO_CTRL_CFG_BIT2);
}
-#else
-#define rt2800usb_rfkill_poll NULL
-#endif /* CONFIG_RT2X00_LIB_RFKILL */
#ifdef CONFIG_RT2X00_LIB_LEDS
static void rt2800usb_brightness_set(struct led_classdev *led_cdev,
rt2x00_set_field32(®, RX_FILTER_CFG_DROP_RTS,
!(filter_flags & FIF_CONTROL));
rt2x00_set_field32(®, RX_FILTER_CFG_DROP_PSPOLL,
- !(filter_flags & FIF_CONTROL));
+ !(filter_flags & FIF_PSPOLL));
rt2x00_set_field32(®, RX_FILTER_CFG_DROP_BA, 1);
rt2x00_set_field32(®, RX_FILTER_CFG_DROP_BAR, 0);
rt2x00_set_field32(®, RX_FILTER_CFG_DROP_CNTL,
/*
* Before the radio can be enabled, the device first has
* to be woken up. After that it needs a bit of time
- * to be fully awake and the radio can be enabled.
+ * to be fully awake and then the radio can be enabled.
*/
rt2800usb_set_state(rt2x00dev, STATE_AWAKE);
msleep(1);
break;
case STATE_RADIO_OFF:
/*
- * After the radio has been disablee, the device should
+ * After the radio has been disabled, the device should
* be put to sleep for powersaving.
*/
rt2800usb_disable_radio(rt2x00dev);
* otherwise we might be sending out invalid data.
*/
rt2x00usb_register_read(rt2x00dev, BCN_TIME_CFG, ®);
- rt2x00_set_field32(®, BCN_TIME_CFG_TSF_TICKING, 0);
- rt2x00_set_field32(®, BCN_TIME_CFG_TBTT_ENABLE, 0);
rt2x00_set_field32(®, BCN_TIME_CFG_BEACON_GEN, 0);
rt2x00usb_register_write(rt2x00dev, BCN_TIME_CFG, reg);
*/
mac = rt2x00_eeprom_addr(rt2x00dev, EEPROM_MAC_ADDR_0);
if (!is_valid_ether_addr(mac)) {
- DECLARE_MAC_BUF(macbuf);
-
random_ether_addr(mac);
- EEPROM(rt2x00dev, "MAC: %s\n", print_mac(macbuf, mac));
+ EEPROM(rt2x00dev, "MAC: %pM\n", mac);
}
rt2x00_eeprom_read(rt2x00dev, EEPROM_ANTENNA, &word);
/*
* Detect if this device has an hardware controlled radio.
*/
-#ifdef CONFIG_RT2X00_LIB_RFKILL
if (rt2x00_get_field16(eeprom, EEPROM_NIC_HW_RADIO))
__set_bit(CONFIG_SUPPORT_HW_BUTTON, &rt2x00dev->flags);
-#endif /* CONFIG_RT2X00_LIB_RFKILL */
/*
* Store led settings, for correct led behaviour.
if (retval)
return retval;
+ /*
+ * This device has multiple filters for control frames
+ * and has a separate filter for PS Poll frames.
+ */
+ __set_bit(DRIVER_SUPPORT_CONTROL_FILTERS, &rt2x00dev->flags);
+ __set_bit(DRIVER_SUPPORT_CONTROL_FILTER_PSPOLL, &rt2x00dev->flags);
+
/*
* This device requires firmware.
*/
.remove_interface = rt2x00mac_remove_interface,
.config = rt2x00mac_config,
.configure_filter = rt2x00mac_configure_filter,
+ .set_tim = rt2x00mac_set_tim,
.set_key = rt2x00mac_set_key,
.get_stats = rt2x00mac_get_stats,
.get_tkip_seq = rt2800usb_get_tkip_seq,
.conf_tx = rt2800usb_conf_tx,
.get_tx_stats = rt2x00mac_get_tx_stats,
.get_tsf = rt2800usb_get_tsf,
+ .rfkill_poll = rt2x00mac_rfkill_poll,
};
static const struct rt2x00lib_ops rt2800usb_rt2x00_ops = {