MODULE_SUPPORTED_DEVICE("Atheros 802.11n WLAN cards");
MODULE_LICENSE("Dual BSD/GPL");
-static struct pci_device_id ath_pci_id_table[] __devinitdata = {
- { PCI_VDEVICE(ATHEROS, 0x0023) }, /* PCI */
- { PCI_VDEVICE(ATHEROS, 0x0024) }, /* PCI-E */
- { PCI_VDEVICE(ATHEROS, 0x0027) }, /* PCI */
- { PCI_VDEVICE(ATHEROS, 0x0029) }, /* PCI */
- { PCI_VDEVICE(ATHEROS, 0x002A) }, /* PCI-E */
- { PCI_VDEVICE(ATHEROS, 0x002B) }, /* PCI-E */
- { 0 }
+/* We use the hw_value as an index into our private channel structure */
+
+#define CHAN2G(_freq, _idx) { \
+ .center_freq = (_freq), \
+ .hw_value = (_idx), \
+ .max_power = 30, \
+}
+
+#define CHAN5G(_freq, _idx) { \
+ .band = IEEE80211_BAND_5GHZ, \
+ .center_freq = (_freq), \
+ .hw_value = (_idx), \
+ .max_power = 30, \
+}
+
+/* Some 2 GHz radios are actually tunable on 2312-2732
+ * on 5 MHz steps, we support the channels which we know
+ * we have calibration data for all cards though to make
+ * this static */
+static struct ieee80211_channel ath9k_2ghz_chantable[] = {
+ CHAN2G(2412, 0), /* Channel 1 */
+ CHAN2G(2417, 1), /* Channel 2 */
+ CHAN2G(2422, 2), /* Channel 3 */
+ CHAN2G(2427, 3), /* Channel 4 */
+ CHAN2G(2432, 4), /* Channel 5 */
+ CHAN2G(2437, 5), /* Channel 6 */
+ CHAN2G(2442, 6), /* Channel 7 */
+ CHAN2G(2447, 7), /* Channel 8 */
+ CHAN2G(2452, 8), /* Channel 9 */
+ CHAN2G(2457, 9), /* Channel 10 */
+ CHAN2G(2462, 10), /* Channel 11 */
+ CHAN2G(2467, 11), /* Channel 12 */
+ CHAN2G(2472, 12), /* Channel 13 */
+ CHAN2G(2484, 13), /* Channel 14 */
};
-static void ath_detach(struct ath_softc *sc);
-
-/* return bus cachesize in 4B word units */
-
-static void bus_read_cachesize(struct ath_softc *sc, int *csz)
-{
- u8 u8tmp;
-
- pci_read_config_byte(sc->pdev, PCI_CACHE_LINE_SIZE, (u8 *)&u8tmp);
- *csz = (int)u8tmp;
-
- /*
- * This check was put in to avoid "unplesant" consequences if
- * the bootrom has not fully initialized all PCI devices.
- * Sometimes the cache line size register is not set
- */
-
- if (*csz == 0)
- *csz = DEFAULT_CACHELINE >> 2; /* Use the default size */
-}
-
-static void ath_setcurmode(struct ath_softc *sc, enum wireless_mode mode)
-{
- sc->cur_rate_table = sc->hw_rate_table[mode];
- /*
- * All protection frames are transmited at 2Mb/s for
- * 11g, otherwise at 1Mb/s.
- * XXX select protection rate index from rate table.
- */
- sc->sc_protrix = (mode == ATH9K_MODE_11G ? 1 : 0);
-}
+/* Some 5 GHz radios are actually tunable on XXXX-YYYY
+ * on 5 MHz steps, we support the channels which we know
+ * we have calibration data for all cards though to make
+ * this static */
+static struct ieee80211_channel ath9k_5ghz_chantable[] = {
+ /* _We_ call this UNII 1 */
+ CHAN5G(5180, 14), /* Channel 36 */
+ CHAN5G(5200, 15), /* Channel 40 */
+ CHAN5G(5220, 16), /* Channel 44 */
+ CHAN5G(5240, 17), /* Channel 48 */
+ /* _We_ call this UNII 2 */
+ CHAN5G(5260, 18), /* Channel 52 */
+ CHAN5G(5280, 19), /* Channel 56 */
+ CHAN5G(5300, 20), /* Channel 60 */
+ CHAN5G(5320, 21), /* Channel 64 */
+ /* _We_ call this "Middle band" */
+ CHAN5G(5500, 22), /* Channel 100 */
+ CHAN5G(5520, 23), /* Channel 104 */
+ CHAN5G(5540, 24), /* Channel 108 */
+ CHAN5G(5560, 25), /* Channel 112 */
+ CHAN5G(5580, 26), /* Channel 116 */
+ CHAN5G(5600, 27), /* Channel 120 */
+ CHAN5G(5620, 28), /* Channel 124 */
+ CHAN5G(5640, 29), /* Channel 128 */
+ CHAN5G(5660, 30), /* Channel 132 */
+ CHAN5G(5680, 31), /* Channel 136 */
+ CHAN5G(5700, 32), /* Channel 140 */
+ /* _We_ call this UNII 3 */
+ CHAN5G(5745, 33), /* Channel 149 */
+ CHAN5G(5765, 34), /* Channel 153 */
+ CHAN5G(5785, 35), /* Channel 157 */
+ CHAN5G(5805, 36), /* Channel 161 */
+ CHAN5G(5825, 37), /* Channel 165 */
+};
-static enum wireless_mode ath_chan2mode(struct ath9k_channel *chan)
+static void ath_cache_conf_rate(struct ath_softc *sc,
+ struct ieee80211_conf *conf)
{
- if (chan->chanmode == CHANNEL_A)
- return ATH9K_MODE_11A;
- else if (chan->chanmode == CHANNEL_G)
- return ATH9K_MODE_11G;
- else if (chan->chanmode == CHANNEL_B)
- return ATH9K_MODE_11B;
- else if (chan->chanmode == CHANNEL_A_HT20)
- return ATH9K_MODE_11NA_HT20;
- else if (chan->chanmode == CHANNEL_G_HT20)
- return ATH9K_MODE_11NG_HT20;
- else if (chan->chanmode == CHANNEL_A_HT40PLUS)
- return ATH9K_MODE_11NA_HT40PLUS;
- else if (chan->chanmode == CHANNEL_A_HT40MINUS)
- return ATH9K_MODE_11NA_HT40MINUS;
- else if (chan->chanmode == CHANNEL_G_HT40PLUS)
- return ATH9K_MODE_11NG_HT40PLUS;
- else if (chan->chanmode == CHANNEL_G_HT40MINUS)
- return ATH9K_MODE_11NG_HT40MINUS;
-
- WARN_ON(1); /* should not get here */
-
- return ATH9K_MODE_11B;
+ switch (conf->channel->band) {
+ case IEEE80211_BAND_2GHZ:
+ if (conf_is_ht20(conf))
+ sc->cur_rate_table =
+ sc->hw_rate_table[ATH9K_MODE_11NG_HT20];
+ else if (conf_is_ht40_minus(conf))
+ sc->cur_rate_table =
+ sc->hw_rate_table[ATH9K_MODE_11NG_HT40MINUS];
+ else if (conf_is_ht40_plus(conf))
+ sc->cur_rate_table =
+ sc->hw_rate_table[ATH9K_MODE_11NG_HT40PLUS];
+ else
+ sc->cur_rate_table =
+ sc->hw_rate_table[ATH9K_MODE_11G];
+ break;
+ case IEEE80211_BAND_5GHZ:
+ if (conf_is_ht20(conf))
+ sc->cur_rate_table =
+ sc->hw_rate_table[ATH9K_MODE_11NA_HT20];
+ else if (conf_is_ht40_minus(conf))
+ sc->cur_rate_table =
+ sc->hw_rate_table[ATH9K_MODE_11NA_HT40MINUS];
+ else if (conf_is_ht40_plus(conf))
+ sc->cur_rate_table =
+ sc->hw_rate_table[ATH9K_MODE_11NA_HT40PLUS];
+ else
+ sc->cur_rate_table =
+ sc->hw_rate_table[ATH9K_MODE_11A];
+ break;
+ default:
+ BUG_ON(1);
+ break;
+ }
}
static void ath_update_txpow(struct ath_softc *sc)
for (i = 0; i < maxrates; i++) {
rate[i].bitrate = rate_table->info[i].ratekbps / 100;
rate[i].hw_value = rate_table->info[i].ratecode;
+ if (rate_table->info[i].short_preamble) {
+ rate[i].hw_value_short = rate_table->info[i].ratecode |
+ rate_table->info[i].short_preamble;
+ rate[i].flags = IEEE80211_RATE_SHORT_PREAMBLE;
+ }
sband->n_bitrates++;
+
DPRINTF(sc, ATH_DBG_CONFIG, "Rate: %2dMbps, ratecode: %2d\n",
rate[i].bitrate / 10, rate[i].hw_value);
}
}
-static int ath_setup_channels(struct ath_softc *sc)
-{
- struct ath_hal *ah = sc->sc_ah;
- int nchan, i, a = 0, b = 0;
- u8 regclassids[ATH_REGCLASSIDS_MAX];
- u32 nregclass = 0;
- struct ieee80211_supported_band *band_2ghz;
- struct ieee80211_supported_band *band_5ghz;
- struct ieee80211_channel *chan_2ghz;
- struct ieee80211_channel *chan_5ghz;
- struct ath9k_channel *c;
-
- /* Fill in ah->ah_channels */
- if (!ath9k_regd_init_channels(ah, ATH_CHAN_MAX, (u32 *)&nchan,
- regclassids, ATH_REGCLASSIDS_MAX,
- &nregclass, CTRY_DEFAULT, false, 1)) {
- u32 rd = ah->ah_currentRD;
- DPRINTF(sc, ATH_DBG_FATAL,
- "Unable to collect channel list; "
- "regdomain likely %u country code %u\n",
- rd, CTRY_DEFAULT);
- return -EINVAL;
- }
-
- band_2ghz = &sc->sbands[IEEE80211_BAND_2GHZ];
- band_5ghz = &sc->sbands[IEEE80211_BAND_5GHZ];
- chan_2ghz = sc->channels[IEEE80211_BAND_2GHZ];
- chan_5ghz = sc->channels[IEEE80211_BAND_5GHZ];
-
- for (i = 0; i < nchan; i++) {
- c = &ah->ah_channels[i];
- if (IS_CHAN_2GHZ(c)) {
- chan_2ghz[a].band = IEEE80211_BAND_2GHZ;
- chan_2ghz[a].center_freq = c->channel;
- chan_2ghz[a].max_power = c->maxTxPower;
-
- if (c->privFlags & CHANNEL_DISALLOW_ADHOC)
- chan_2ghz[a].flags |= IEEE80211_CHAN_NO_IBSS;
- if (c->channelFlags & CHANNEL_PASSIVE)
- chan_2ghz[a].flags |= IEEE80211_CHAN_PASSIVE_SCAN;
-
- band_2ghz->n_channels = ++a;
-
- DPRINTF(sc, ATH_DBG_CONFIG, "2MHz channel: %d, "
- "channelFlags: 0x%x\n",
- c->channel, c->channelFlags);
- } else if (IS_CHAN_5GHZ(c)) {
- chan_5ghz[b].band = IEEE80211_BAND_5GHZ;
- chan_5ghz[b].center_freq = c->channel;
- chan_5ghz[b].max_power = c->maxTxPower;
-
- if (c->privFlags & CHANNEL_DISALLOW_ADHOC)
- chan_5ghz[b].flags |= IEEE80211_CHAN_NO_IBSS;
- if (c->channelFlags & CHANNEL_PASSIVE)
- chan_5ghz[b].flags |= IEEE80211_CHAN_PASSIVE_SCAN;
-
- band_5ghz->n_channels = ++b;
-
- DPRINTF(sc, ATH_DBG_CONFIG, "5MHz channel: %d, "
- "channelFlags: 0x%x\n",
- c->channel, c->channelFlags);
- }
- }
-
- return 0;
-}
-
/*
* Set/change channels. If the channel is really being changed, it's done
* by reseting the chip. To accomplish this we must first cleanup any pending
{
struct ath_hal *ah = sc->sc_ah;
bool fastcc = true, stopped;
+ struct ieee80211_hw *hw = sc->hw;
+ struct ieee80211_channel *channel = hw->conf.channel;
+ int r;
if (sc->sc_flags & SC_OP_INVALID)
return -EIO;
- if (hchan->channel != sc->sc_ah->ah_curchan->channel ||
- hchan->channelFlags != sc->sc_ah->ah_curchan->channelFlags ||
- (sc->sc_flags & SC_OP_CHAINMASK_UPDATE) ||
- (sc->sc_flags & SC_OP_FULL_RESET)) {
- int status;
- /*
- * This is only performed if the channel settings have
- * actually changed.
- *
- * To switch channels clear any pending DMA operations;
- * wait long enough for the RX fifo to drain, reset the
- * hardware at the new frequency, and then re-enable
- * the relevant bits of the h/w.
- */
- ath9k_hw_set_interrupts(ah, 0);
- ath_draintxq(sc, false);
- stopped = ath_stoprecv(sc);
-
- /* XXX: do not flush receive queue here. We don't want
- * to flush data frames already in queue because of
- * changing channel. */
-
- if (!stopped || (sc->sc_flags & SC_OP_FULL_RESET))
- fastcc = false;
-
- DPRINTF(sc, ATH_DBG_CONFIG,
- "(%u MHz) -> (%u MHz), cflags:%x, chanwidth: %d\n",
- sc->sc_ah->ah_curchan->channel,
- hchan->channel, hchan->channelFlags, sc->tx_chan_width);
-
- spin_lock_bh(&sc->sc_resetlock);
- if (!ath9k_hw_reset(ah, hchan, sc->tx_chan_width,
- sc->sc_tx_chainmask, sc->sc_rx_chainmask,
- sc->sc_ht_extprotspacing, fastcc, &status)) {
- DPRINTF(sc, ATH_DBG_FATAL,
- "Unable to reset channel %u (%uMhz) "
- "flags 0x%x hal status %u\n",
- ath9k_hw_mhz2ieee(ah, hchan->channel,
- hchan->channelFlags),
- hchan->channel, hchan->channelFlags, status);
- spin_unlock_bh(&sc->sc_resetlock);
- return -EIO;
- }
- spin_unlock_bh(&sc->sc_resetlock);
+ ath9k_ps_wakeup(sc);
+
+ /*
+ * This is only performed if the channel settings have
+ * actually changed.
+ *
+ * To switch channels clear any pending DMA operations;
+ * wait long enough for the RX fifo to drain, reset the
+ * hardware at the new frequency, and then re-enable
+ * the relevant bits of the h/w.
+ */
+ ath9k_hw_set_interrupts(ah, 0);
+ ath_drain_all_txq(sc, false);
+ stopped = ath_stoprecv(sc);
- sc->sc_flags &= ~SC_OP_CHAINMASK_UPDATE;
- sc->sc_flags &= ~SC_OP_FULL_RESET;
+ /* XXX: do not flush receive queue here. We don't want
+ * to flush data frames already in queue because of
+ * changing channel. */
- if (ath_startrecv(sc) != 0) {
- DPRINTF(sc, ATH_DBG_FATAL,
- "Unable to restart recv logic\n");
- return -EIO;
- }
+ if (!stopped || (sc->sc_flags & SC_OP_FULL_RESET))
+ fastcc = false;
- ath_setcurmode(sc, ath_chan2mode(hchan));
- ath_update_txpow(sc);
- ath9k_hw_set_interrupts(ah, sc->sc_imask);
+ DPRINTF(sc, ATH_DBG_CONFIG,
+ "(%u MHz) -> (%u MHz), chanwidth: %d\n",
+ sc->sc_ah->ah_curchan->channel,
+ channel->center_freq, sc->tx_chan_width);
+
+ spin_lock_bh(&sc->sc_resetlock);
+
+ r = ath9k_hw_reset(ah, hchan, fastcc);
+ if (r) {
+ DPRINTF(sc, ATH_DBG_FATAL,
+ "Unable to reset channel (%u Mhz) "
+ "reset status %u\n",
+ channel->center_freq, r);
+ spin_unlock_bh(&sc->sc_resetlock);
+ return r;
}
+ spin_unlock_bh(&sc->sc_resetlock);
+
+ sc->sc_flags &= ~SC_OP_CHAINMASK_UPDATE;
+ sc->sc_flags &= ~SC_OP_FULL_RESET;
+
+ if (ath_startrecv(sc) != 0) {
+ DPRINTF(sc, ATH_DBG_FATAL,
+ "Unable to restart recv logic\n");
+ return -EIO;
+ }
+
+ ath_cache_conf_rate(sc, &hw->conf);
+ ath_update_txpow(sc);
+ ath9k_hw_set_interrupts(ah, sc->sc_imask);
+ ath9k_ps_restore(sc);
return 0;
}
} else {
if ((timestamp - sc->sc_ani.sc_resetcal_timer) >=
ATH_RESTART_CALINTERVAL) {
- ath9k_hw_reset_calvalid(ah, ah->ah_curchan,
- &sc->sc_ani.sc_caldone);
+ sc->sc_ani.sc_caldone = ath9k_hw_reset_calvalid(ah);
if (sc->sc_ani.sc_caldone)
sc->sc_ani.sc_resetcal_timer = timestamp;
}
/*
* Update tx/rx chainmask. For legacy association,
* hard code chainmask to 1x1, for 11n association, use
- * the chainmask configuration.
+ * the chainmask configuration, for bt coexistence, use
+ * the chainmask configuration even in legacy mode.
*/
static void ath_update_chainmask(struct ath_softc *sc, int is_ht)
{
sc->sc_flags |= SC_OP_CHAINMASK_UPDATE;
- if (is_ht) {
+ if (is_ht ||
+ (sc->sc_ah->ah_caps.hw_caps & ATH9K_HW_CAP_BT_COEX)) {
sc->sc_tx_chainmask = sc->sc_ah->ah_caps.tx_chainmask;
sc->sc_rx_chainmask = sc->sc_ah->ah_caps.rx_chainmask;
} else {
ath9k_hw_set_interrupts(sc->sc_ah, sc->sc_imask);
}
-static irqreturn_t ath_isr(int irq, void *dev)
+irqreturn_t ath_isr(int irq, void *dev)
{
struct ath_softc *sc = dev;
struct ath_hal *ah = sc->sc_ah;
ATH9K_HW_CAP_AUTOSLEEP)) {
/* Clear RxAbort bit so that we can
* receive frames */
+ ath9k_hw_setpower(ah, ATH9K_PM_AWAKE);
ath9k_hw_setrxabort(ah, 0);
sched = true;
+ sc->sc_flags |= SC_OP_WAIT_FOR_BEACON;
}
}
}
return IRQ_HANDLED;
}
-static int ath_get_channel(struct ath_softc *sc,
- struct ieee80211_channel *chan)
-{
- int i;
-
- for (i = 0; i < sc->sc_ah->ah_nchan; i++) {
- if (sc->sc_ah->ah_channels[i].channel == chan->center_freq)
- return i;
- }
-
- return -1;
-}
-
static u32 ath_get_extchanmode(struct ath_softc *sc,
struct ieee80211_channel *chan,
enum nl80211_channel_type channel_type)
}
static int ath_key_config(struct ath_softc *sc,
- const u8 *addr,
+ struct ieee80211_sta *sta,
struct ieee80211_key_conf *key)
{
struct ath9k_keyval hk;
hk.kv_type = ATH9K_CIPHER_AES_CCM;
break;
default:
- return -EINVAL;
+ return -EOPNOTSUPP;
}
hk.kv_len = key->keylen;
} else if (key->keyidx) {
struct ieee80211_vif *vif;
- mac = addr;
+ if (WARN_ON(!sta))
+ return -EOPNOTSUPP;
+ mac = sta->addr;
+
vif = sc->sc_vaps[0];
if (vif->type != NL80211_IFTYPE_AP) {
/* Only keyidx 0 should be used with unicast key, but
} else
return -EIO;
} else {
- mac = addr;
+ if (WARN_ON(!sta))
+ return -EOPNOTSUPP;
+ mac = sta->addr;
+
if (key->alg == ALG_TKIP)
idx = ath_reserve_key_cache_slot_tkip(sc);
else
idx = ath_reserve_key_cache_slot(sc);
if (idx < 0)
- return -EIO; /* no free key cache entries */
+ return -ENOSPC; /* no free key cache entries */
}
if (key->alg == ALG_TKIP)
}
}
-static void setup_ht_cap(struct ieee80211_sta_ht_cap *ht_info)
+static void setup_ht_cap(struct ath_softc *sc,
+ struct ieee80211_sta_ht_cap *ht_info)
{
#define ATH9K_HT_CAP_MAXRXAMPDU_65536 0x3 /* 2 ^ 16 */
#define ATH9K_HT_CAP_MPDUDENSITY_8 0x6 /* 8 usec */
ht_info->ampdu_factor = ATH9K_HT_CAP_MAXRXAMPDU_65536;
ht_info->ampdu_density = ATH9K_HT_CAP_MPDUDENSITY_8;
+
/* set up supported mcs set */
memset(&ht_info->mcs, 0, sizeof(ht_info->mcs));
- ht_info->mcs.rx_mask[0] = 0xff;
- ht_info->mcs.rx_mask[1] = 0xff;
+
+ switch(sc->sc_rx_chainmask) {
+ case 1:
+ ht_info->mcs.rx_mask[0] = 0xff;
+ break;
+ case 3:
+ case 5:
+ case 7:
+ default:
+ ht_info->mcs.rx_mask[0] = 0xff;
+ ht_info->mcs.rx_mask[1] = 0xff;
+ break;
+ }
+
ht_info->mcs.tx_params = IEEE80211_HT_MCS_TX_DEFINED;
}
static void ath_radio_enable(struct ath_softc *sc)
{
struct ath_hal *ah = sc->sc_ah;
- int status;
+ struct ieee80211_channel *channel = sc->hw->conf.channel;
+ int r;
+ ath9k_ps_wakeup(sc);
spin_lock_bh(&sc->sc_resetlock);
- if (!ath9k_hw_reset(ah, ah->ah_curchan,
- sc->tx_chan_width,
- sc->sc_tx_chainmask,
- sc->sc_rx_chainmask,
- sc->sc_ht_extprotspacing,
- false, &status)) {
+
+ r = ath9k_hw_reset(ah, ah->ah_curchan, false);
+
+ if (r) {
DPRINTF(sc, ATH_DBG_FATAL,
- "Unable to reset channel %u (%uMhz) "
- "flags 0x%x hal status %u\n",
- ath9k_hw_mhz2ieee(ah,
- ah->ah_curchan->channel,
- ah->ah_curchan->channelFlags),
- ah->ah_curchan->channel,
- ah->ah_curchan->channelFlags, status);
+ "Unable to reset channel %u (%uMhz) ",
+ "reset status %u\n",
+ channel->center_freq, r);
}
spin_unlock_bh(&sc->sc_resetlock);
ath9k_hw_set_gpio(ah, ATH_LED_PIN, 0);
ieee80211_wake_queues(sc->hw);
+ ath9k_ps_restore(sc);
}
static void ath_radio_disable(struct ath_softc *sc)
{
struct ath_hal *ah = sc->sc_ah;
- int status;
-
+ struct ieee80211_channel *channel = sc->hw->conf.channel;
+ int r;
+ ath9k_ps_wakeup(sc);
ieee80211_stop_queues(sc->hw);
/* Disable LED */
/* Disable interrupts */
ath9k_hw_set_interrupts(ah, 0);
- ath_draintxq(sc, false); /* clear pending tx frames */
+ ath_drain_all_txq(sc, false); /* clear pending tx frames */
ath_stoprecv(sc); /* turn off frame recv */
ath_flushrecv(sc); /* flush recv queue */
spin_lock_bh(&sc->sc_resetlock);
- if (!ath9k_hw_reset(ah, ah->ah_curchan,
- sc->tx_chan_width,
- sc->sc_tx_chainmask,
- sc->sc_rx_chainmask,
- sc->sc_ht_extprotspacing,
- false, &status)) {
+ r = ath9k_hw_reset(ah, ah->ah_curchan, false);
+ if (r) {
DPRINTF(sc, ATH_DBG_FATAL,
"Unable to reset channel %u (%uMhz) "
- "flags 0x%x hal status %u\n",
- ath9k_hw_mhz2ieee(ah,
- ah->ah_curchan->channel,
- ah->ah_curchan->channelFlags),
- ah->ah_curchan->channel,
- ah->ah_curchan->channelFlags, status);
+ "reset status %u\n",
+ channel->center_freq, r);
}
spin_unlock_bh(&sc->sc_resetlock);
ath9k_hw_phy_disable(ah);
ath9k_hw_setpower(ah, ATH9K_PM_FULL_SLEEP);
+ ath9k_ps_restore(sc);
}
static bool ath_is_rfkill_set(struct ath_softc *sc)
rfkill_free(sc->rf_kill.rfkill);
/* Deinitialize the device */
- ath_detach(sc);
- if (sc->pdev->irq)
- free_irq(sc->pdev->irq, sc);
- pci_iounmap(sc->pdev, sc->mem);
- pci_release_region(sc->pdev, 0);
- pci_disable_device(sc->pdev);
- ieee80211_free_hw(sc->hw);
+ ath_cleanup(sc);
return -EIO;
} else {
sc->sc_flags |= SC_OP_RFKILL_REGISTERED;
}
#endif /* CONFIG_RFKILL */
-static void ath_detach(struct ath_softc *sc)
+void ath_cleanup(struct ath_softc *sc)
+{
+ ath_detach(sc);
+ free_irq(sc->irq, sc);
+ ath_bus_cleanup(sc);
+ ieee80211_free_hw(sc->hw);
+}
+
+void ath_detach(struct ath_softc *sc)
{
struct ieee80211_hw *hw = sc->hw;
int i = 0;
+ ath9k_ps_wakeup(sc);
+
DPRINTF(sc, ATH_DBG_CONFIG, "Detach ATH hw\n");
#if defined(CONFIG_RFKILL) || defined(CONFIG_RFKILL_MODULE)
ath9k_hw_detach(sc->sc_ah);
ath9k_exit_debug(sc);
+ ath9k_ps_restore(sc);
}
static int ath_init(u16 devid, struct ath_softc *sc)
* Cache line size is used to size and align various
* structures used to communicate with the hardware.
*/
- bus_read_cachesize(sc, &csz);
+ ath_read_cachesize(sc, &csz);
/* XXX assert csz is non-zero */
sc->sc_cachelsz = csz << 2; /* convert to bytes */
ah = ath9k_hw_attach(devid, sc, sc->mem, &status);
if (ah == NULL) {
DPRINTF(sc, ATH_DBG_FATAL,
- "Unable to attach hardware; HAL status %u\n", status);
+ "Unable to attach hardware; HAL status %d\n", status);
error = -ENXIO;
goto bad;
}
for (i = 0; i < sc->sc_keymax; i++)
ath9k_hw_keyreset(ah, (u16) i);
- /* Collect the channel list using the default country code */
-
- error = ath_setup_channels(sc);
- if (error)
+ if (ath9k_regd_init(sc->sc_ah))
goto bad;
/* default to MONITOR mode */
sc->sc_ah->ah_opmode = NL80211_IFTYPE_MONITOR;
-
/* Setup rate tables */
ath_rate_attach(sc);
/* setup channels and rates */
- sc->sbands[IEEE80211_BAND_2GHZ].channels =
- sc->channels[IEEE80211_BAND_2GHZ];
+ sc->sbands[IEEE80211_BAND_2GHZ].channels = ath9k_2ghz_chantable;
sc->sbands[IEEE80211_BAND_2GHZ].bitrates =
sc->rates[IEEE80211_BAND_2GHZ];
sc->sbands[IEEE80211_BAND_2GHZ].band = IEEE80211_BAND_2GHZ;
+ sc->sbands[IEEE80211_BAND_2GHZ].n_channels =
+ ARRAY_SIZE(ath9k_2ghz_chantable);
if (test_bit(ATH9K_MODE_11A, sc->sc_ah->ah_caps.wireless_modes)) {
- sc->sbands[IEEE80211_BAND_5GHZ].channels =
- sc->channels[IEEE80211_BAND_5GHZ];
+ sc->sbands[IEEE80211_BAND_5GHZ].channels = ath9k_5ghz_chantable;
sc->sbands[IEEE80211_BAND_5GHZ].bitrates =
sc->rates[IEEE80211_BAND_5GHZ];
sc->sbands[IEEE80211_BAND_5GHZ].band = IEEE80211_BAND_5GHZ;
+ sc->sbands[IEEE80211_BAND_5GHZ].n_channels =
+ ARRAY_SIZE(ath9k_5ghz_chantable);
}
+ if (sc->sc_ah->ah_caps.hw_caps & ATH9K_HW_CAP_BT_COEX)
+ ath9k_hw_btcoex_enable(sc->sc_ah);
+
return 0;
bad2:
/* cleanup tx queues */
return error;
}
-static int ath_attach(u16 devid, struct ath_softc *sc)
+int ath_attach(u16 devid, struct ath_softc *sc)
{
struct ieee80211_hw *hw = sc->hw;
int error = 0;
hw->flags = IEEE80211_HW_RX_INCLUDES_FCS |
IEEE80211_HW_HOST_BROADCAST_PS_BUFFERING |
IEEE80211_HW_SIGNAL_DBM |
- IEEE80211_HW_AMPDU_AGGREGATION;
+ IEEE80211_HW_AMPDU_AGGREGATION |
+ IEEE80211_HW_SUPPORTS_PS |
+ IEEE80211_HW_PS_NULLFUNC_STACK;
+
+ if (AR_SREV_9160_10_OR_LATER(sc->sc_ah))
+ hw->flags |= IEEE80211_HW_MFP_CAPABLE;
hw->wiphy->interface_modes =
BIT(NL80211_IFTYPE_AP) |
BIT(NL80211_IFTYPE_STATION) |
BIT(NL80211_IFTYPE_ADHOC);
+ hw->wiphy->reg_notifier = ath9k_reg_notifier;
+ hw->wiphy->strict_regulatory = true;
+
hw->queues = 4;
hw->max_rates = 4;
hw->max_rate_tries = ATH_11N_TXMAXTRY;
hw->rate_control_algorithm = "ath9k_rate_control";
if (sc->sc_ah->ah_caps.hw_caps & ATH9K_HW_CAP_HT) {
- setup_ht_cap(&sc->sbands[IEEE80211_BAND_2GHZ].ht_cap);
+ setup_ht_cap(sc, &sc->sbands[IEEE80211_BAND_2GHZ].ht_cap);
if (test_bit(ATH9K_MODE_11A, sc->sc_ah->ah_caps.wireless_modes))
- setup_ht_cap(&sc->sbands[IEEE80211_BAND_5GHZ].ht_cap);
+ setup_ht_cap(sc, &sc->sbands[IEEE80211_BAND_5GHZ].ht_cap);
}
hw->wiphy->bands[IEEE80211_BAND_2GHZ] = &sc->sbands[IEEE80211_BAND_2GHZ];
goto detach;
#endif
+ if (ath9k_is_world_regd(sc->sc_ah)) {
+ /* Anything applied here (prior to wiphy registratoin) gets
+ * saved on the wiphy orig_* parameters */
+ const struct ieee80211_regdomain *regd =
+ ath9k_world_regdomain(sc->sc_ah);
+ hw->wiphy->custom_regulatory = true;
+ hw->wiphy->strict_regulatory = false;
+ wiphy_apply_custom_regulatory(sc->hw->wiphy, regd);
+ ath9k_reg_apply_radar_flags(hw->wiphy);
+ ath9k_reg_apply_world_flags(hw->wiphy, REGDOM_SET_BY_INIT);
+ } else {
+ /* This gets applied in the case of the absense of CRDA,
+ * its our own custom world regulatory domain, similar to
+ * cfg80211's but we enable passive scanning */
+ const struct ieee80211_regdomain *regd =
+ ath9k_default_world_regdomain();
+ wiphy_apply_custom_regulatory(sc->hw->wiphy, regd);
+ ath9k_reg_apply_radar_flags(hw->wiphy);
+ ath9k_reg_apply_world_flags(hw->wiphy, REGDOM_SET_BY_INIT);
+ }
+
error = ieee80211_register_hw(hw);
+ if (!ath9k_is_world_regd(sc->sc_ah))
+ regulatory_hint(hw->wiphy, sc->sc_ah->alpha2);
+
/* Initialize LED control */
ath_init_leds(sc);
+
return 0;
detach:
ath_detach(sc);
int ath_reset(struct ath_softc *sc, bool retry_tx)
{
struct ath_hal *ah = sc->sc_ah;
- int status;
- int error = 0;
+ struct ieee80211_hw *hw = sc->hw;
+ int r;
ath9k_hw_set_interrupts(ah, 0);
- ath_draintxq(sc, retry_tx);
+ ath_drain_all_txq(sc, retry_tx);
ath_stoprecv(sc);
ath_flushrecv(sc);
spin_lock_bh(&sc->sc_resetlock);
- if (!ath9k_hw_reset(ah, sc->sc_ah->ah_curchan,
- sc->tx_chan_width,
- sc->sc_tx_chainmask, sc->sc_rx_chainmask,
- sc->sc_ht_extprotspacing, false, &status)) {
+ r = ath9k_hw_reset(ah, sc->sc_ah->ah_curchan, false);
+ if (r)
DPRINTF(sc, ATH_DBG_FATAL,
- "Unable to reset hardware; hal status %u\n", status);
- error = -EIO;
- }
+ "Unable to reset hardware; reset status %u\n", r);
spin_unlock_bh(&sc->sc_resetlock);
if (ath_startrecv(sc) != 0)
* that changes the channel so update any state that
* might change as a result.
*/
- ath_setcurmode(sc, ath_chan2mode(sc->sc_ah->ah_curchan));
+ ath_cache_conf_rate(sc, &hw->conf);
ath_update_txpow(sc);
}
}
- return error;
+ return r;
}
/*
}
/* allocate descriptors */
- dd->dd_desc = pci_alloc_consistent(sc->pdev,
- dd->dd_desc_len,
- &dd->dd_desc_paddr);
+ dd->dd_desc = dma_alloc_coherent(sc->dev, dd->dd_desc_len,
+ &dd->dd_desc_paddr, GFP_ATOMIC);
if (dd->dd_desc == NULL) {
error = -ENOMEM;
goto fail;
}
return 0;
fail2:
- pci_free_consistent(sc->pdev,
- dd->dd_desc_len, dd->dd_desc, dd->dd_desc_paddr);
+ dma_free_coherent(sc->dev, dd->dd_desc_len, dd->dd_desc,
+ dd->dd_desc_paddr);
fail:
memset(dd, 0, sizeof(*dd));
return error;
struct ath_descdma *dd,
struct list_head *head)
{
- pci_free_consistent(sc->pdev,
- dd->dd_desc_len, dd->dd_desc, dd->dd_desc_paddr);
+ dma_free_coherent(sc->dev, dd->dd_desc_len, dd->dd_desc,
+ dd->dd_desc_paddr);
INIT_LIST_HEAD(head);
kfree(dd->dd_bufptr);
return qnum;
}
+/* XXX: Remove me once we don't depend on ath9k_channel for all
+ * this redundant data */
+static void ath9k_update_ichannel(struct ath_softc *sc,
+ struct ath9k_channel *ichan)
+{
+ struct ieee80211_hw *hw = sc->hw;
+ struct ieee80211_channel *chan = hw->conf.channel;
+ struct ieee80211_conf *conf = &hw->conf;
+
+ ichan->channel = chan->center_freq;
+ ichan->chan = chan;
+
+ if (chan->band == IEEE80211_BAND_2GHZ) {
+ ichan->chanmode = CHANNEL_G;
+ ichan->channelFlags = CHANNEL_2GHZ | CHANNEL_OFDM;
+ } else {
+ ichan->chanmode = CHANNEL_A;
+ ichan->channelFlags = CHANNEL_5GHZ | CHANNEL_OFDM;
+ }
+
+ sc->tx_chan_width = ATH9K_HT_MACMODE_20;
+
+ if (conf_is_ht(conf)) {
+ if (conf_is_ht40(conf))
+ sc->tx_chan_width = ATH9K_HT_MACMODE_2040;
+
+ ichan->chanmode = ath_get_extchanmode(sc, chan,
+ conf->channel_type);
+ }
+}
+
/**********************/
/* mac80211 callbacks */
/**********************/
struct ath_softc *sc = hw->priv;
struct ieee80211_channel *curchan = hw->conf.channel;
struct ath9k_channel *init_channel;
- int error = 0, pos, status;
+ int r, pos;
DPRINTF(sc, ATH_DBG_CONFIG, "Starting driver with "
"initial channel: %d MHz\n", curchan->center_freq);
/* setup initial channel */
- pos = ath_get_channel(sc, curchan);
- if (pos == -1) {
- DPRINTF(sc, ATH_DBG_FATAL, "Invalid channel: %d\n", curchan->center_freq);
- error = -EINVAL;
- goto error;
- }
+ pos = curchan->hw_value;
- sc->tx_chan_width = ATH9K_HT_MACMODE_20;
- sc->sc_ah->ah_channels[pos].chanmode =
- (curchan->band == IEEE80211_BAND_2GHZ) ? CHANNEL_G : CHANNEL_A;
init_channel = &sc->sc_ah->ah_channels[pos];
+ ath9k_update_ichannel(sc, init_channel);
/* Reset SERDES registers */
ath9k_hw_configpcipowersave(sc->sc_ah, 0);
* and then setup of the interrupt mask.
*/
spin_lock_bh(&sc->sc_resetlock);
- if (!ath9k_hw_reset(sc->sc_ah, init_channel,
- sc->tx_chan_width,
- sc->sc_tx_chainmask, sc->sc_rx_chainmask,
- sc->sc_ht_extprotspacing, false, &status)) {
+ r = ath9k_hw_reset(sc->sc_ah, init_channel, false);
+ if (r) {
DPRINTF(sc, ATH_DBG_FATAL,
- "Unable to reset hardware; hal status %u "
- "(freq %u flags 0x%x)\n", status,
- init_channel->channel, init_channel->channelFlags);
- error = -EIO;
+ "Unable to reset hardware; reset status %u "
+ "(freq %u MHz)\n", r,
+ curchan->center_freq);
spin_unlock_bh(&sc->sc_resetlock);
- goto error;
+ return r;
}
spin_unlock_bh(&sc->sc_resetlock);
if (ath_startrecv(sc) != 0) {
DPRINTF(sc, ATH_DBG_FATAL,
"Unable to start recv logic\n");
- error = -EIO;
- goto error;
+ return -EIO;
}
/* Setup our intr mask. */
if (sc->sc_ah->ah_caps.hw_caps & ATH9K_HW_CAP_HT)
sc->sc_imask |= ATH9K_INT_CST;
- /*
- * Enable MIB interrupts when there are hardware phy counters.
- * Note we only do this (at the moment) for station mode.
- */
- if (ath9k_hw_phycounters(sc->sc_ah) &&
- ((sc->sc_ah->ah_opmode == NL80211_IFTYPE_STATION) ||
- (sc->sc_ah->ah_opmode == NL80211_IFTYPE_ADHOC)))
- sc->sc_imask |= ATH9K_INT_MIB;
- /*
- * Some hardware processes the TIM IE and fires an
- * interrupt when the TIM bit is set. For hardware
- * that does, if not overridden by configuration,
- * enable the TIM interrupt when operating as station.
- */
- if ((sc->sc_ah->ah_caps.hw_caps & ATH9K_HW_CAP_ENHANCEDPM) &&
- (sc->sc_ah->ah_opmode == NL80211_IFTYPE_STATION) &&
- !sc->sc_config.swBeaconProcess)
- sc->sc_imask |= ATH9K_INT_TIM;
-
- ath_setcurmode(sc, ath_chan2mode(init_channel));
+ ath_cache_conf_rate(sc, &hw->conf);
sc->sc_flags &= ~SC_OP_INVALID;
ieee80211_wake_queues(sc->hw);
#if defined(CONFIG_RFKILL) || defined(CONFIG_RFKILL_MODULE)
- error = ath_start_rfkill_poll(sc);
+ r = ath_start_rfkill_poll(sc);
#endif
-
-error:
- return error;
+ return r;
}
static int ath9k_tx(struct ieee80211_hw *hw,
ath9k_hw_set_interrupts(sc->sc_ah, 0);
if (!(sc->sc_flags & SC_OP_INVALID)) {
- ath_draintxq(sc, false);
+ ath_drain_all_txq(sc, false);
ath_stoprecv(sc);
ath9k_hw_phy_disable(sc->sc_ah);
} else
/* Set the device opmode */
sc->sc_ah->ah_opmode = ic_opmode;
+ /*
+ * Enable MIB interrupts when there are hardware phy counters.
+ * Note we only do this (at the moment) for station mode.
+ */
+ if (ath9k_hw_phycounters(sc->sc_ah) &&
+ ((conf->type == NL80211_IFTYPE_STATION) ||
+ (conf->type == NL80211_IFTYPE_ADHOC)))
+ sc->sc_imask |= ATH9K_INT_MIB;
+ /*
+ * Some hardware processes the TIM IE and fires an
+ * interrupt when the TIM bit is set. For hardware
+ * that does, if not overridden by configuration,
+ * enable the TIM interrupt when operating as station.
+ */
+ if ((sc->sc_ah->ah_caps.hw_caps & ATH9K_HW_CAP_ENHANCEDPM) &&
+ (conf->type == NL80211_IFTYPE_STATION) &&
+ !sc->sc_config.swBeaconProcess)
+ sc->sc_imask |= ATH9K_INT_TIM;
+
+ ath9k_hw_set_interrupts(sc->sc_ah, sc->sc_imask);
+
if (conf->type == NL80211_IFTYPE_AP) {
/* TODO: is this a suitable place to start ANI for AP mode? */
/* Start ANI */
struct ieee80211_conf *conf = &hw->conf;
mutex_lock(&sc->mutex);
- if (changed & (IEEE80211_CONF_CHANGE_CHANNEL |
- IEEE80211_CONF_CHANGE_HT)) {
+ if (changed & IEEE80211_CONF_CHANGE_PS) {
+ if (conf->flags & IEEE80211_CONF_PS) {
+ if ((sc->sc_imask & ATH9K_INT_TIM_TIMER) == 0) {
+ sc->sc_imask |= ATH9K_INT_TIM_TIMER;
+ ath9k_hw_set_interrupts(sc->sc_ah,
+ sc->sc_imask);
+ }
+ ath9k_hw_setrxabort(sc->sc_ah, 1);
+ ath9k_hw_setpower(sc->sc_ah, ATH9K_PM_NETWORK_SLEEP);
+ } else {
+ ath9k_hw_setpower(sc->sc_ah, ATH9K_PM_AWAKE);
+ ath9k_hw_setrxabort(sc->sc_ah, 0);
+ sc->sc_flags &= ~SC_OP_WAIT_FOR_BEACON;
+ if (sc->sc_imask & ATH9K_INT_TIM_TIMER) {
+ sc->sc_imask &= ~ATH9K_INT_TIM_TIMER;
+ ath9k_hw_set_interrupts(sc->sc_ah,
+ sc->sc_imask);
+ }
+ }
+ }
+
+ if (changed & IEEE80211_CONF_CHANGE_CHANNEL) {
struct ieee80211_channel *curchan = hw->conf.channel;
- int pos;
+ int pos = curchan->hw_value;
DPRINTF(sc, ATH_DBG_CONFIG, "Set channel: %d MHz\n",
curchan->center_freq);
- pos = ath_get_channel(sc, curchan);
- if (pos == -1) {
- DPRINTF(sc, ATH_DBG_FATAL, "Invalid channel: %d\n",
- curchan->center_freq);
- mutex_unlock(&sc->mutex);
- return -EINVAL;
- }
-
- sc->tx_chan_width = ATH9K_HT_MACMODE_20;
- sc->sc_ah->ah_channels[pos].chanmode =
- (curchan->band == IEEE80211_BAND_2GHZ) ?
- CHANNEL_G : CHANNEL_A;
+ /* XXX: remove me eventualy */
+ ath9k_update_ichannel(sc, &sc->sc_ah->ah_channels[pos]);
- if (conf->ht.enabled) {
- if (conf->ht.channel_type == NL80211_CHAN_HT40PLUS ||
- conf->ht.channel_type == NL80211_CHAN_HT40MINUS)
- sc->tx_chan_width = ATH9K_HT_MACMODE_2040;
-
- sc->sc_ah->ah_channels[pos].chanmode =
- ath_get_extchanmode(sc, curchan,
- conf->ht.channel_type);
- }
+ ath_update_chainmask(sc, conf_is_ht(conf));
if (ath_set_channel(sc, &sc->sc_ah->ah_channels[pos]) < 0) {
DPRINTF(sc, ATH_DBG_FATAL, "Unable to set channel\n");
mutex_unlock(&sc->mutex);
return -EINVAL;
}
-
- ath_update_chainmask(sc, conf->ht.enabled);
}
if (changed & IEEE80211_CONF_CHANGE_POWER)
}
}
- if ((conf->changed & IEEE80211_IFCC_BEACON) &&
- ((vif->type == NL80211_IFTYPE_ADHOC) ||
- (vif->type == NL80211_IFTYPE_AP))) {
- /*
- * Allocate and setup the beacon frame.
- *
- * Stop any previous beacon DMA. This may be
- * necessary, for example, when an ibss merge
- * causes reconfiguration; we may be called
- * with beacon transmission active.
- */
- ath9k_hw_stoptxdma(sc->sc_ah, sc->beacon.beaconq);
+ if ((vif->type == NL80211_IFTYPE_ADHOC) ||
+ (vif->type == NL80211_IFTYPE_AP)) {
+ if ((conf->changed & IEEE80211_IFCC_BEACON) ||
+ (conf->changed & IEEE80211_IFCC_BEACON_ENABLED &&
+ conf->enable_beacon)) {
+ /*
+ * Allocate and setup the beacon frame.
+ *
+ * Stop any previous beacon DMA. This may be
+ * necessary, for example, when an ibss merge
+ * causes reconfiguration; we may be called
+ * with beacon transmission active.
+ */
+ ath9k_hw_stoptxdma(sc->sc_ah, sc->beacon.beaconq);
- error = ath_beacon_alloc(sc, 0);
- if (error != 0)
- return error;
+ error = ath_beacon_alloc(sc, 0);
+ if (error != 0)
+ return error;
- ath_beacon_sync(sc, 0);
+ ath_beacon_sync(sc, 0);
+ }
}
/* Check for WLAN_CAPABILITY_PRIVACY ? */
static int ath9k_set_key(struct ieee80211_hw *hw,
enum set_key_cmd cmd,
- const u8 *local_addr,
- const u8 *addr,
+ struct ieee80211_vif *vif,
+ struct ieee80211_sta *sta,
struct ieee80211_key_conf *key)
{
struct ath_softc *sc = hw->priv;
int ret = 0;
+ ath9k_ps_wakeup(sc);
DPRINTF(sc, ATH_DBG_KEYCACHE, "Set HW Key\n");
switch (cmd) {
case SET_KEY:
- ret = ath_key_config(sc, addr, key);
+ ret = ath_key_config(sc, sta, key);
if (ret >= 0) {
key->hw_key_idx = ret;
/* push IV and Michael MIC generation to stack */
key->flags |= IEEE80211_KEY_FLAG_GENERATE_IV;
if (key->alg == ALG_TKIP)
key->flags |= IEEE80211_KEY_FLAG_GENERATE_MMIC;
+ if (sc->sc_ah->sw_mgmt_crypto && key->alg == ALG_CCMP)
+ key->flags |= IEEE80211_KEY_FLAG_SW_MGMT;
ret = 0;
}
break;
ret = -EINVAL;
}
+ ath9k_ps_restore(sc);
return ret;
}
return tsf;
}
+static void ath9k_set_tsf(struct ieee80211_hw *hw, u64 tsf)
+{
+ struct ath_softc *sc = hw->priv;
+ struct ath_hal *ah = sc->sc_ah;
+
+ ath9k_hw_settsf64(ah, tsf);
+}
+
static void ath9k_reset_tsf(struct ieee80211_hw *hw)
{
struct ath_softc *sc = hw->priv;
return ret;
}
-static struct ieee80211_ops ath9k_ops = {
+struct ieee80211_ops ath9k_ops = {
.tx = ath9k_tx,
.start = ath9k_start,
.stop = ath9k_stop,
.bss_info_changed = ath9k_bss_info_changed,
.set_key = ath9k_set_key,
.get_tsf = ath9k_get_tsf,
+ .set_tsf = ath9k_set_tsf,
.reset_tsf = ath9k_reset_tsf,
.ampdu_action = ath9k_ampdu_action,
};
/*
* Return the MAC/BB name. "????" is returned if the MAC/BB is unknown.
*/
-static const char *
+const char *
ath_mac_bb_name(u32 mac_bb_version)
{
int i;
/*
* Return the RF name. "????" is returned if the RF is unknown.
*/
-static const char *
+const char *
ath_rf_name(u16 rf_version)
{
int i;
return "????";
}
-static int ath_pci_probe(struct pci_dev *pdev, const struct pci_device_id *id)
-{
- void __iomem *mem;
- struct ath_softc *sc;
- struct ieee80211_hw *hw;
- u8 csz;
- u32 val;
- int ret = 0;
- struct ath_hal *ah;
-
- if (pci_enable_device(pdev))
- return -EIO;
-
- ret = pci_set_dma_mask(pdev, DMA_32BIT_MASK);
-
- if (ret) {
- printk(KERN_ERR "ath9k: 32-bit DMA not available\n");
- goto bad;
- }
-
- ret = pci_set_consistent_dma_mask(pdev, DMA_32BIT_MASK);
-
- if (ret) {
- printk(KERN_ERR "ath9k: 32-bit DMA consistent "
- "DMA enable failed\n");
- goto bad;
- }
-
- /*
- * Cache line size is used to size and align various
- * structures used to communicate with the hardware.
- */
- pci_read_config_byte(pdev, PCI_CACHE_LINE_SIZE, &csz);
- if (csz == 0) {
- /*
- * Linux 2.4.18 (at least) writes the cache line size
- * register as a 16-bit wide register which is wrong.
- * We must have this setup properly for rx buffer
- * DMA to work so force a reasonable value here if it
- * comes up zero.
- */
- csz = L1_CACHE_BYTES / sizeof(u32);
- pci_write_config_byte(pdev, PCI_CACHE_LINE_SIZE, csz);
- }
- /*
- * The default setting of latency timer yields poor results,
- * set it to the value used by other systems. It may be worth
- * tweaking this setting more.
- */
- pci_write_config_byte(pdev, PCI_LATENCY_TIMER, 0xa8);
-
- pci_set_master(pdev);
-
- /*
- * Disable the RETRY_TIMEOUT register (0x41) to keep
- * PCI Tx retries from interfering with C3 CPU state.
- */
- pci_read_config_dword(pdev, 0x40, &val);
- if ((val & 0x0000ff00) != 0)
- pci_write_config_dword(pdev, 0x40, val & 0xffff00ff);
-
- ret = pci_request_region(pdev, 0, "ath9k");
- if (ret) {
- dev_err(&pdev->dev, "PCI memory region reserve error\n");
- ret = -ENODEV;
- goto bad;
- }
-
- mem = pci_iomap(pdev, 0, 0);
- if (!mem) {
- printk(KERN_ERR "PCI memory map error\n") ;
- ret = -EIO;
- goto bad1;
- }
-
- hw = ieee80211_alloc_hw(sizeof(struct ath_softc), &ath9k_ops);
- if (hw == NULL) {
- printk(KERN_ERR "ath_pci: no memory for ieee80211_hw\n");
- goto bad2;
- }
-
- SET_IEEE80211_DEV(hw, &pdev->dev);
- pci_set_drvdata(pdev, hw);
-
- sc = hw->priv;
- sc->hw = hw;
- sc->pdev = pdev;
- sc->mem = mem;
-
- if (ath_attach(id->device, sc) != 0) {
- ret = -ENODEV;
- goto bad3;
- }
-
- /* setup interrupt service routine */
-
- if (request_irq(pdev->irq, ath_isr, IRQF_SHARED, "ath", sc)) {
- printk(KERN_ERR "%s: request_irq failed\n",
- wiphy_name(hw->wiphy));
- ret = -EIO;
- goto bad4;
- }
-
- ah = sc->sc_ah;
- printk(KERN_INFO
- "%s: Atheros AR%s MAC/BB Rev:%x "
- "AR%s RF Rev:%x: mem=0x%lx, irq=%d\n",
- wiphy_name(hw->wiphy),
- ath_mac_bb_name(ah->ah_macVersion),
- ah->ah_macRev,
- ath_rf_name((ah->ah_analog5GhzRev & AR_RADIO_SREV_MAJOR)),
- ah->ah_phyRev,
- (unsigned long)mem, pdev->irq);
-
- return 0;
-bad4:
- ath_detach(sc);
-bad3:
- ieee80211_free_hw(hw);
-bad2:
- pci_iounmap(pdev, mem);
-bad1:
- pci_release_region(pdev, 0);
-bad:
- pci_disable_device(pdev);
- return ret;
-}
-
-static void ath_pci_remove(struct pci_dev *pdev)
-{
- struct ieee80211_hw *hw = pci_get_drvdata(pdev);
- struct ath_softc *sc = hw->priv;
-
- ath_detach(sc);
- if (pdev->irq)
- free_irq(pdev->irq, sc);
- pci_iounmap(pdev, sc->mem);
- pci_release_region(pdev, 0);
- pci_disable_device(pdev);
- ieee80211_free_hw(hw);
-}
-
-#ifdef CONFIG_PM
-
-static int ath_pci_suspend(struct pci_dev *pdev, pm_message_t state)
-{
- struct ieee80211_hw *hw = pci_get_drvdata(pdev);
- struct ath_softc *sc = hw->priv;
-
- ath9k_hw_set_gpio(sc->sc_ah, ATH_LED_PIN, 1);
-
-#if defined(CONFIG_RFKILL) || defined(CONFIG_RFKILL_MODULE)
- if (sc->sc_ah->ah_caps.hw_caps & ATH9K_HW_CAP_RFSILENT)
- cancel_delayed_work_sync(&sc->rf_kill.rfkill_poll);
-#endif
-
- pci_save_state(pdev);
- pci_disable_device(pdev);
- pci_set_power_state(pdev, 3);
-
- return 0;
-}
-
-static int ath_pci_resume(struct pci_dev *pdev)
-{
- struct ieee80211_hw *hw = pci_get_drvdata(pdev);
- struct ath_softc *sc = hw->priv;
- u32 val;
- int err;
-
- err = pci_enable_device(pdev);
- if (err)
- return err;
- pci_restore_state(pdev);
- /*
- * Suspend/Resume resets the PCI configuration space, so we have to
- * re-disable the RETRY_TIMEOUT register (0x41) to keep
- * PCI Tx retries from interfering with C3 CPU state
- */
- pci_read_config_dword(pdev, 0x40, &val);
- if ((val & 0x0000ff00) != 0)
- pci_write_config_dword(pdev, 0x40, val & 0xffff00ff);
-
- /* Enable LED */
- ath9k_hw_cfg_output(sc->sc_ah, ATH_LED_PIN,
- AR_GPIO_OUTPUT_MUX_AS_OUTPUT);
- ath9k_hw_set_gpio(sc->sc_ah, ATH_LED_PIN, 1);
-
-#if defined(CONFIG_RFKILL) || defined(CONFIG_RFKILL_MODULE)
- /*
- * check the h/w rfkill state on resume
- * and start the rfkill poll timer
- */
- if (sc->sc_ah->ah_caps.hw_caps & ATH9K_HW_CAP_RFSILENT)
- queue_delayed_work(sc->hw->workqueue,
- &sc->rf_kill.rfkill_poll, 0);
-#endif
-
- return 0;
-}
-
-#endif /* CONFIG_PM */
-
-MODULE_DEVICE_TABLE(pci, ath_pci_id_table);
-
-static struct pci_driver ath_pci_driver = {
- .name = "ath9k",
- .id_table = ath_pci_id_table,
- .probe = ath_pci_probe,
- .remove = ath_pci_remove,
-#ifdef CONFIG_PM
- .suspend = ath_pci_suspend,
- .resume = ath_pci_resume,
-#endif /* CONFIG_PM */
-};
-
-static int __init init_ath_pci(void)
+static int __init ath9k_init(void)
{
int error;
- printk(KERN_INFO "%s: %s\n", dev_info, ATH_PCI_VERSION);
-
/* Register rate control algorithm */
error = ath_rate_control_register();
if (error != 0) {
printk(KERN_ERR
- "Unable to register rate control algorithm: %d\n",
+ "ath9k: Unable to register rate control "
+ "algorithm: %d\n",
error);
- ath_rate_control_unregister();
- return error;
+ goto err_out;
}
- if (pci_register_driver(&ath_pci_driver) < 0) {
+ error = ath_pci_init();
+ if (error < 0) {
printk(KERN_ERR
- "ath_pci: No devices found, driver not installed.\n");
- ath_rate_control_unregister();
- pci_unregister_driver(&ath_pci_driver);
- return -ENODEV;
+ "ath9k: No PCI devices found, driver not installed.\n");
+ error = -ENODEV;
+ goto err_rate_unregister;
+ }
+
+ error = ath_ahb_init();
+ if (error < 0) {
+ error = -ENODEV;
+ goto err_pci_exit;
}
return 0;
+
+ err_pci_exit:
+ ath_pci_exit();
+
+ err_rate_unregister:
+ ath_rate_control_unregister();
+ err_out:
+ return error;
}
-module_init(init_ath_pci);
+module_init(ath9k_init);
-static void __exit exit_ath_pci(void)
+static void __exit ath9k_exit(void)
{
+ ath_ahb_exit();
+ ath_pci_exit();
ath_rate_control_unregister();
- pci_unregister_driver(&ath_pci_driver);
printk(KERN_INFO "%s: Driver unloaded\n", dev_info);
}
-module_exit(exit_ath_pci);
+module_exit(ath9k_exit);
git.openpandora.org / pandora-kernel.git / blobdiff