config PLAT_SAMSUNG
bool
depends on ARCH_S3C2410 || ARCH_S3C24A0 || ARCH_S3C64XX || ARCH_S5PC1XX
+ select NO_IOPORT
default y
help
Base platform code for all Samsung SoC based systems
if PLAT_SAMSUNG
+# boot configurations
+
+comment "Boot options"
+
+config S3C_BOOT_WATCHDOG
+ bool "S3C Initialisation watchdog"
+ depends on S3C2410_WATCHDOG
+ help
+ Say y to enable the watchdog during the kernel decompression
+ stage. If the kernel fails to uncompress, then the watchdog
+ will trigger a reset and the system should restart.
+
+config S3C_BOOT_ERROR_RESET
+ bool "S3C Reboot on decompression error"
+ help
+ Say y here to use the watchdog to reset the system if the
+ kernel decompressor detects an error during decompression.
+
+config S3C_BOOT_UART_FORCE_FIFO
+ bool "Force UART FIFO on during boot process"
+ default y
+ help
+ Say Y here to force the UART FIFOs on during the kernel
+ uncompressor
+
+
+config S3C_LOWLEVEL_UART_PORT
+ int "S3C UART to use for low-level messages"
+ default 0
+ help
+ Choice of which UART port to use for the low-level messages,
+ such as the `Uncompressing...` at start time. The value of
+ this configuration should be between zero and two. The port
+ must have been initialised by the boot-loader before use.
+
+# clock options
+
+config SAMSUNG_CLKSRC
+ bool
+ help
+ Select the clock code for the clksrc implementation
+ used by newer systems such as the S3C64XX.
+
+# options for IRQ support
+
+config SAMSUNG_IRQ_VIC_TIMER
+ bool
+ help
+ Internal configuration to build the VIC timer interrupt code.
+
+config SAMSUNG_IRQ_UART
+ bool
+ help
+ Internal configuration to build the IRQ UART demux code.
+
+# options for gpio configuration support
+
+config SAMSUNG_GPIOLIB_4BIT
+ bool
+ help
+ GPIOlib file contains the 4 bit modification functions for gpio
+ configuration. GPIOlib shall be compiled only for S3C64XX and S5P
+ series of processors.
+
+config S3C_GPIO_CFG_S3C24XX
+ bool
+ help
+ Internal configuration to enable S3C24XX style GPIO configuration
+ functions.
+
+config S3C_GPIO_CFG_S3C64XX
+ bool
+ help
+ Internal configuration to enable S3C64XX style GPIO configuration
+ functions.
+
+config S3C_GPIO_PULL_UPDOWN
+ bool
+ help
+ Internal configuration to enable the correct GPIO pull helper
+
+config S3C_GPIO_PULL_DOWN
+ bool
+ help
+ Internal configuration to enable the correct GPIO pull helper
+
+config S3C_GPIO_PULL_UP
+ bool
+ help
+ Internal configuration to enable the correct GPIO pull helper
+
+config S5P_GPIO_DRVSTR
+ bool
+ help
+ Internal configuration to get and set correct GPIO driver strength
+ helper
+
+config SAMSUNG_GPIO_EXTRA
+ int "Number of additional GPIO pins"
+ default 0
+ help
+ Use additional GPIO space in addition to the GPIO's the SOC
+ provides. This allows expanding the GPIO space for use with
+ GPIO expanders.
+
+config S3C_GPIO_SPACE
+ int "Space between gpio banks"
+ default 0
+ help
+ Add a number of spare GPIO entries between each bank for debugging
+ purposes. This allows any problems where an counter overflows from
+ one bank to another to be caught, at the expense of using a little
+ more memory.
+
+config S3C_GPIO_TRACK
+ bool
+ help
+ Internal configuration option to enable the s3c specific gpio
+ chip tracking if the platform requires it.
+
+# ADC driver
+
+config S3C_ADC
+ bool "ADC common driver support"
+ help
+ Core support for the ADC block found in the Samsung SoC systems
+ for drivers such as the touchscreen and hwmon to use to share
+ this resource.
+
+# device definitions to compile in
+
+config S3C_DEV_HSMMC
+ bool
+ help
+ Compile in platform device definitions for HSMMC code
+
+config S3C_DEV_HSMMC1
+ bool
+ help
+ Compile in platform device definitions for HSMMC channel 1
+
+config S3C_DEV_HSMMC2
+ bool
+ help
+ Compile in platform device definitions for HSMMC channel 2
+
+config S3C_DEV_HWMON
+ bool
+ help
+ Compile in platform device definitions for HWMON
+
+config S3C_DEV_I2C1
+ bool
+ help
+ Compile in platform device definitions for I2C channel 1
+
+config S3C_DEV_FB
+ bool
+ help
+ Compile in platform device definition for framebuffer
+
+config S3C_DEV_USB_HOST
+ bool
+ help
+ Compile in platform device definition for USB host.
+
+config S3C_DEV_USB_HSOTG
+ bool
+ help
+ Compile in platform device definition for USB high-speed OtG
+
+config S3C_DEV_NAND
+ bool
+ help
+ Compile in platform device definition for NAND controller
+
+config S3C_DEV_RTC
+ bool
+ help
+ Complie in platform device definition for RTC
+
+config SAMSUNG_DEV_ADC
+ bool
+ help
+ Compile in platform device definition for ADC controller
+
+config S3C64XX_DEV_SPI
+ bool
+ help
+ Compile in platform device definitions for S3C64XX's type
+ SPI controllers.
+
+config S3C64XX_DEV_TS
+ bool
+ help
+ Common in platform device definitions for S3C64XX touchscreen
+ device
+
+# DMA
+
+config S3C_DMA
+ bool
+ help
+ Internal configuration for S3C DMA core
+
+config S3C_PL330_DMA
+ bool
+ select PL330
+ help
+ S3C DMA API Driver for PL330 DMAC.
+
+comment "Power management"
+
+config SAMSUNG_PM_DEBUG
+ bool "S3C2410 PM Suspend debug"
+ depends on PM
+ help
+ Say Y here if you want verbose debugging from the PM Suspend and
+ Resume code. See <file:Documentation/arm/Samsung-S3C24XX/Suspend.txt>
+ for more information.
+
+config S3C_PM_DEBUG_LED_SMDK
+ bool "SMDK LED suspend/resume debugging"
+ depends on PM && (MACH_SMDK6410)
+ help
+ Say Y here to enable the use of the SMDK LEDs on the baseboard
+ for debugging of the state of the suspend and resume process.
+
+ Note, this currently only works for S3C64XX based SMDK boards.
+
+config SAMSUNG_PM_CHECK
+ bool "S3C2410 PM Suspend Memory CRC"
+ depends on PM && CRC32
+ help
+ Enable the PM code's memory area checksum over sleep. This option
+ will generate CRCs of all blocks of memory, and store them before
+ going to sleep. The blocks are then checked on resume for any
+ errors.
+
+ Note, this can take several seconds depending on memory size
+ and CPU speed.
+
+ See <file:Documentation/arm/Samsung-S3C24XX/Suspend.txt>
+
+config SAMSUNG_PM_CHECK_CHUNKSIZE
+ int "S3C2410 PM Suspend CRC Chunksize (KiB)"
+ depends on PM && SAMSUNG_PM_CHECK
+ default 64
+ help
+ Set the chunksize in Kilobytes of the CRC for checking memory
+ corruption over suspend and resume. A smaller value will mean that
+ the CRC data block will take more memory, but wil identify any
+ faults with better precision.
+
+ See <file:Documentation/arm/Samsung-S3C24XX/Suspend.txt>
endif
git.openpandora.org / pandora-kernel.git / blobdiff