#include "mux.h"
#include "sdram-micron-mt46h32m32lf-6.h"
#include "hsmmc.h"
+#include "common-board-devices.h"
#define CM_T35_GPIO_PENDOWN 57
#if defined(CONFIG_SMSC911X) || defined(CONFIG_SMSC911X_MODULE)
#include <linux/smsc911x.h>
+#include <plat/gpmc-smsc911x.h>
-static struct smsc911x_platform_config cm_t35_smsc911x_config = {
- .irq_polarity = SMSC911X_IRQ_POLARITY_ACTIVE_LOW,
- .irq_type = SMSC911X_IRQ_TYPE_OPEN_DRAIN,
- .flags = SMSC911X_USE_32BIT | SMSC911X_SAVE_MAC_ADDRESS,
- .phy_interface = PHY_INTERFACE_MODE_MII,
-};
-
-static struct resource cm_t35_smsc911x_resources[] = {
- {
- .flags = IORESOURCE_MEM,
- },
- {
- .start = OMAP_GPIO_IRQ(CM_T35_SMSC911X_GPIO),
- .end = OMAP_GPIO_IRQ(CM_T35_SMSC911X_GPIO),
- .flags = IORESOURCE_IRQ | IORESOURCE_IRQ_LOWLEVEL,
- },
-};
-
-static struct platform_device cm_t35_smsc911x_device = {
- .name = "smsc911x",
+static struct omap_smsc911x_platform_data cm_t35_smsc911x_cfg = {
.id = 0,
- .num_resources = ARRAY_SIZE(cm_t35_smsc911x_resources),
- .resource = cm_t35_smsc911x_resources,
- .dev = {
- .platform_data = &cm_t35_smsc911x_config,
- },
-};
-
-static struct resource sb_t35_smsc911x_resources[] = {
- {
- .flags = IORESOURCE_MEM,
- },
- {
- .start = OMAP_GPIO_IRQ(SB_T35_SMSC911X_GPIO),
- .end = OMAP_GPIO_IRQ(SB_T35_SMSC911X_GPIO),
- .flags = IORESOURCE_IRQ | IORESOURCE_IRQ_LOWLEVEL,
- },
+ .cs = CM_T35_SMSC911X_CS,
+ .gpio_irq = CM_T35_SMSC911X_GPIO,
+ .gpio_reset = -EINVAL,
+ .flags = SMSC911X_USE_32BIT | SMSC911X_SAVE_MAC_ADDRESS,
};
-static struct platform_device sb_t35_smsc911x_device = {
- .name = "smsc911x",
+static struct omap_smsc911x_platform_data sb_t35_smsc911x_cfg = {
.id = 1,
- .num_resources = ARRAY_SIZE(sb_t35_smsc911x_resources),
- .resource = sb_t35_smsc911x_resources,
- .dev = {
- .platform_data = &cm_t35_smsc911x_config,
- },
+ .cs = SB_T35_SMSC911X_CS,
+ .gpio_irq = SB_T35_SMSC911X_GPIO,
+ .gpio_reset = -EINVAL,
+ .flags = SMSC911X_USE_32BIT | SMSC911X_SAVE_MAC_ADDRESS,
};
-static void __init cm_t35_init_smsc911x(struct platform_device *dev,
- int cs, int irq_gpio)
-{
- unsigned long cs_mem_base;
-
- if (gpmc_cs_request(cs, SZ_16M, &cs_mem_base) < 0) {
- pr_err("CM-T35: Failed request for GPMC mem for smsc911x\n");
- return;
- }
-
- dev->resource[0].start = cs_mem_base + 0x0;
- dev->resource[0].end = cs_mem_base + 0xff;
-
- if ((gpio_request(irq_gpio, "ETH IRQ") == 0) &&
- (gpio_direction_input(irq_gpio) == 0)) {
- gpio_export(irq_gpio, 0);
- } else {
- pr_err("CM-T35: could not obtain gpio for SMSC911X IRQ\n");
- return;
- }
-
- platform_device_register(dev);
-}
-
static void __init cm_t35_init_ethernet(void)
{
- cm_t35_init_smsc911x(&cm_t35_smsc911x_device,
- CM_T35_SMSC911X_CS, CM_T35_SMSC911X_GPIO);
- cm_t35_init_smsc911x(&sb_t35_smsc911x_device,
- SB_T35_SMSC911X_CS, SB_T35_SMSC911X_GPIO);
+ gpmc_smsc911x_init(&cm_t35_smsc911x_cfg);
+ gpmc_smsc911x_init(&sb_t35_smsc911x_cfg);
}
#else
static inline void __init cm_t35_init_ethernet(void) { return; }
static inline void cm_t35_init_nand(void) {}
#endif
-#if defined(CONFIG_TOUCHSCREEN_ADS7846) || \
- defined(CONFIG_TOUCHSCREEN_ADS7846_MODULE)
-#include <linux/spi/ads7846.h>
-
-static struct omap2_mcspi_device_config ads7846_mcspi_config = {
- .turbo_mode = 0,
- .single_channel = 1, /* 0: slave, 1: master */
-};
-
-static int ads7846_get_pendown_state(void)
-{
- return !gpio_get_value(CM_T35_GPIO_PENDOWN);
-}
-
-static struct ads7846_platform_data ads7846_config = {
- .x_max = 0x0fff,
- .y_max = 0x0fff,
- .x_plate_ohms = 180,
- .pressure_max = 255,
- .debounce_max = 10,
- .debounce_tol = 3,
- .debounce_rep = 1,
- .get_pendown_state = ads7846_get_pendown_state,
- .keep_vref_on = 1,
-};
-
-static struct spi_board_info cm_t35_spi_board_info[] __initdata = {
- {
- .modalias = "ads7846",
- .bus_num = 1,
- .chip_select = 0,
- .max_speed_hz = 1500000,
- .controller_data = &ads7846_mcspi_config,
- .irq = OMAP_GPIO_IRQ(CM_T35_GPIO_PENDOWN),
- .platform_data = &ads7846_config,
- },
-};
-
-static void __init cm_t35_init_ads7846(void)
-{
- if ((gpio_request(CM_T35_GPIO_PENDOWN, "ADS7846_PENDOWN") == 0) &&
- (gpio_direction_input(CM_T35_GPIO_PENDOWN) == 0)) {
- gpio_export(CM_T35_GPIO_PENDOWN, 0);
- } else {
- pr_err("CM-T35: could not obtain gpio for ADS7846_PENDOWN\n");
- return;
- }
-
- spi_register_board_info(cm_t35_spi_board_info,
- ARRAY_SIZE(cm_t35_spi_board_info));
-}
-#else
-static inline void cm_t35_init_ads7846(void) {}
-#endif
-
#define CM_T35_LCD_EN_GPIO 157
#define CM_T35_LCD_BL_GPIO 58
#define CM_T35_DVI_EN_GPIO 54
-static int lcd_bl_gpio;
-static int lcd_en_gpio;
-static int dvi_en_gpio;
-
static int lcd_enabled;
static int dvi_enabled;
return -EINVAL;
}
- gpio_set_value(lcd_en_gpio, 1);
- gpio_set_value(lcd_bl_gpio, 1);
+ gpio_set_value(CM_T35_LCD_EN_GPIO, 1);
+ gpio_set_value(CM_T35_LCD_BL_GPIO, 1);
lcd_enabled = 1;
{
lcd_enabled = 0;
- gpio_set_value(lcd_bl_gpio, 0);
- gpio_set_value(lcd_en_gpio, 0);
+ gpio_set_value(CM_T35_LCD_BL_GPIO, 0);
+ gpio_set_value(CM_T35_LCD_EN_GPIO, 0);
}
static int cm_t35_panel_enable_dvi(struct omap_dss_device *dssdev)
return -EINVAL;
}
- gpio_set_value(dvi_en_gpio, 0);
+ gpio_set_value(CM_T35_DVI_EN_GPIO, 0);
dvi_enabled = 1;
return 0;
static void cm_t35_panel_disable_dvi(struct omap_dss_device *dssdev)
{
- gpio_set_value(dvi_en_gpio, 1);
+ gpio_set_value(CM_T35_DVI_EN_GPIO, 1);
dvi_enabled = 0;
}
},
};
+static struct gpio cm_t35_dss_gpios[] __initdata = {
+ { CM_T35_LCD_EN_GPIO, GPIOF_OUT_INIT_LOW, "lcd enable" },
+ { CM_T35_LCD_BL_GPIO, GPIOF_OUT_INIT_LOW, "lcd bl enable" },
+ { CM_T35_DVI_EN_GPIO, GPIOF_OUT_INIT_HIGH, "dvi enable" },
+};
+
static void __init cm_t35_init_display(void)
{
int err;
- lcd_en_gpio = CM_T35_LCD_EN_GPIO;
- lcd_bl_gpio = CM_T35_LCD_BL_GPIO;
- dvi_en_gpio = CM_T35_DVI_EN_GPIO;
-
spi_register_board_info(cm_t35_lcd_spi_board_info,
ARRAY_SIZE(cm_t35_lcd_spi_board_info));
- err = gpio_request(lcd_en_gpio, "LCD RST");
- if (err) {
- pr_err("CM-T35: failed to get LCD reset GPIO\n");
- goto out;
- }
-
- err = gpio_request(lcd_bl_gpio, "LCD BL");
+ err = gpio_request_array(cm_t35_dss_gpios,
+ ARRAY_SIZE(cm_t35_dss_gpios));
if (err) {
- pr_err("CM-T35: failed to get LCD backlight control GPIO\n");
- goto err_lcd_bl;
- }
-
- err = gpio_request(dvi_en_gpio, "DVI EN");
- if (err) {
- pr_err("CM-T35: failed to get DVI reset GPIO\n");
- goto err_dvi_en;
+ pr_err("CM-T35: failed to request DSS control GPIOs\n");
+ return;
}
- gpio_export(lcd_en_gpio, 0);
- gpio_export(lcd_bl_gpio, 0);
- gpio_export(dvi_en_gpio, 0);
- gpio_direction_output(lcd_en_gpio, 0);
- gpio_direction_output(lcd_bl_gpio, 0);
- gpio_direction_output(dvi_en_gpio, 1);
+ gpio_export(CM_T35_LCD_EN_GPIO, 0);
+ gpio_export(CM_T35_LCD_BL_GPIO, 0);
+ gpio_export(CM_T35_DVI_EN_GPIO, 0);
msleep(50);
- gpio_set_value(lcd_en_gpio, 1);
+ gpio_set_value(CM_T35_LCD_EN_GPIO, 1);
err = omap_display_init(&cm_t35_dss_data);
if (err) {
pr_err("CM-T35: failed to register DSS device\n");
- goto err_dev_reg;
+ gpio_free_array(cm_t35_dss_gpios, ARRAY_SIZE(cm_t35_dss_gpios));
}
-
- return;
-
-err_dev_reg:
- gpio_free(dvi_en_gpio);
-err_dvi_en:
- gpio_free(lcd_bl_gpio);
-err_lcd_bl:
- gpio_free(lcd_en_gpio);
-out:
-
- return;
}
static struct regulator_consumer_supply cm_t35_vmmc1_supply = {
{
int wlan_rst = gpio + 2;
- if ((gpio_request(wlan_rst, "WLAN RST") == 0) &&
- (gpio_direction_output(wlan_rst, 1) == 0)) {
+ if (gpio_request_one(wlan_rst, GPIOF_OUT_INIT_HIGH, "WLAN RST") == 0) {
gpio_export(wlan_rst, 0);
-
udelay(10);
gpio_set_value(wlan_rst, 0);
udelay(10);
.vpll2 = &cm_t35_vpll2,
};
-static struct i2c_board_info __initdata cm_t35_i2c_boardinfo[] = {
- {
- I2C_BOARD_INFO("tps65930", 0x48),
- .flags = I2C_CLIENT_WAKE,
- .irq = INT_34XX_SYS_NIRQ,
- .platform_data = &cm_t35_twldata,
- },
-};
-
static void __init cm_t35_init_i2c(void)
{
- omap_register_i2c_bus(1, 2600, cm_t35_i2c_boardinfo,
- ARRAY_SIZE(cm_t35_i2c_boardinfo));
+ omap3_pmic_init("tps65930", &cm_t35_twldata);
}
static void __init cm_t35_init_early(void)
};
#endif
-static struct omap_musb_board_data musb_board_data = {
- .interface_type = MUSB_INTERFACE_ULPI,
- .mode = MUSB_OTG,
- .power = 100,
-};
-
static struct omap_board_config_kernel cm_t35_config[] __initdata = {
};
omap_serial_init();
cm_t35_init_i2c();
cm_t35_init_nand();
- cm_t35_init_ads7846();
+ omap_ads7846_init(1, CM_T35_GPIO_PENDOWN, 0, NULL);
cm_t35_init_ethernet();
cm_t35_init_led();
cm_t35_init_display();
- usb_musb_init(&musb_board_data);
+ usb_musb_init(NULL);
usbhs_init(&usbhs_bdata);
}
git.openpandora.org / pandora-kernel.git / blobdiff