select HAVE_GENERIC_HARDIRQS
select HAVE_SPARSE_IRQ
select GENERIC_IRQ_SHOW
+ select CPU_PM if (SUSPEND || CPU_IDLE)
help
The ARM series is a line of low-power-consumption RISC chip designs
licensed by ARM Ltd and targeted at embedded applications and
this feature (eg, building a kernel for a single machine) and
you need to shrink the kernel to the minimal size.
+config NEED_MACH_MEMORY_H
+ bool
+ help
+ Select this when mach/memory.h is required to provide special
+ definitions for this platform. The need for mach/memory.h should
+ be avoided when possible.
+
+config PHYS_OFFSET
+ hex "Physical address of main memory"
+ depends on !ARM_PATCH_PHYS_VIRT && !NEED_MACH_MEMORY_H
+ help
+ Please provide the physical address corresponding to the
+ location of main memory in your system.
config GENERIC_BUG
def_bool y
select GENERIC_CLOCKEVENTS
select PLAT_VERSATILE
select PLAT_VERSATILE_FPGA_IRQ
+ select NEED_MACH_MEMORY_H
help
Support for ARM's Integrator platform.
select PLAT_VERSATILE_CLCD
select ARM_TIMER_SP804
select GPIO_PL061 if GPIOLIB
+ select NEED_MACH_MEMORY_H
help
This enables support for ARM Ltd RealView boards.
bool "Cirrus Logic CLPS711x/EP721x-based"
select CPU_ARM720T
select ARCH_USES_GETTIMEOFFSET
+ select NEED_MACH_MEMORY_H
help
Support for Cirrus Logic 711x/721x based boards.
select ISA
select NO_IOPORT
select ARCH_USES_GETTIMEOFFSET
+ select NEED_MACH_MEMORY_H
help
This is an evaluation board for the StrongARM processor available
from Digital. It has limited hardware on-board, including an
select ARCH_REQUIRE_GPIOLIB
select ARCH_HAS_HOLES_MEMORYMODEL
select ARCH_USES_GETTIMEOFFSET
+ select NEED_MEMORY_H
help
This enables support for the Cirrus EP93xx series of CPUs.
select FOOTBRIDGE
select GENERIC_CLOCKEVENTS
select HAVE_IDE
+ select NEED_MACH_MEMORY_H
help
Support for systems based on the DC21285 companion chip
("FootBridge"), such as the Simtec CATS and the Rebel NetWinder.
select PCI
select ARCH_SUPPORTS_MSI
select VMSPLIT_1G
+ select NEED_MACH_MEMORY_H
help
Support for Intel's IOP13XX (XScale) family of processors.
select CPU_XSC3
select PCI
select ARCH_USES_GETTIMEOFFSET
+ select NEED_MACH_MEMORY_H
help
Support for Intel's IXP23xx (XScale) family of processors.
select CPU_XSCALE
select PCI
select ARCH_USES_GETTIMEOFFSET
+ select NEED_MACH_MEMORY_H
help
Support for Intel's IXP2400/2800 (XScale) family of processors.
select CPU_ARM922T
select ARCH_REQUIRE_GPIOLIB
select ARCH_USES_GETTIMEOFFSET
+ select NEED_MACH_MEMORY_H
help
Support for Micrel/Kendin KS8695 "Centaur" (ARM922T) based
System-on-Chip devices.
select SPARSE_IRQ
select MULTI_IRQ_HANDLER
select PM_GENERIC_DOMAINS if PM
+ select NEED_MACH_MEMORY_H
help
Support for Renesas's SH-Mobile and R-Mobile ARM platforms.
select ARCH_SPARSEMEM_ENABLE
select ARCH_USES_GETTIMEOFFSET
select HAVE_IDE
+ select NEED_MACH_MEMORY_H
help
On the Acorn Risc-PC, Linux can support the internal IDE disk and
CD-ROM interface, serial and parallel port, and the floppy drive.
select TICK_ONESHOT
select ARCH_REQUIRE_GPIOLIB
select HAVE_IDE
+ select NEED_MACH_MEMORY_H
help
Support for StrongARM 11x0 based boards.
select HAVE_S3C2410_I2C if I2C
select HAVE_S3C_RTC if RTC_CLASS
select HAVE_S3C2410_WATCHDOG if WATCHDOG
+ select NEED_MACH_MEMORY_H
help
Samsung S5PV210/S5PC110 series based systems
select HAVE_S3C_RTC if RTC_CLASS
select HAVE_S3C2410_I2C if I2C
select HAVE_S3C2410_WATCHDOG if WATCHDOG
+ select NEED_MACH_MEMORY_H
help
Samsung EXYNOS4 series based systems
select ZONE_DMA
select PCI
select ARCH_USES_GETTIMEOFFSET
+ select NEED_MACH_MEMORY_H
help
Support for the StrongARM based Digital DNARD machine, also known
as "Shark" (<http://www.shark-linux.de/shark.html>).
select HAVE_MACH_CLKDEV
select GENERIC_GPIO
select ARCH_REQUIRE_GPIOLIB
+ select NEED_MACH_MEMORY_H
help
Support for ST-Ericsson U300 series mobile platforms.
endchoice
+config ARM_APPENDED_DTB
+ bool "Use appended device tree blob to zImage (EXPERIMENTAL)"
+ depends on OF && !ZBOOT_ROM && EXPERIMENTAL
+ help
+ With this option, the boot code will look for a device tree binary
+ (DTB) appended to zImage
+ (e.g. cat zImage <filename>.dtb > zImage_w_dtb).
+
+ This is meant as a backward compatibility convenience for those
+ systems with a bootloader that can't be upgraded to accommodate
+ the documented boot protocol using a device tree.
+
+ Beware that there is very little in terms of protection against
+ this option being confused by leftover garbage in memory that might
+ look like a DTB header after a reboot if no actual DTB is appended
+ to zImage. Do not leave this option active in a production kernel
+ if you don't intend to always append a DTB. Proper passing of the
+ location into r2 of a bootloader provided DTB is always preferable
+ to this option.
+
+config ARM_ATAG_DTB_COMPAT
+ bool "Supplement the appended DTB with traditional ATAG information"
+ depends on ARM_APPENDED_DTB
+ help
+ Some old bootloaders can't be updated to a DTB capable one, yet
+ they provide ATAGs with memory configuration, the ramdisk address,
+ the kernel cmdline string, etc. Such information is dynamically
+ provided by the bootloader and can't always be stored in a static
+ DTB. To allow a device tree enabled kernel to be used with such
+ bootloaders, this option allows zImage to extract the information
+ from the ATAG list and store it at run time into the appended DTB.
+
config CMDLINE
string "Default kernel command string"
default ""