# # Touchscreen driver configuration # menuconfig INPUT_TOUCHSCREEN bool "Touchscreens" help Say Y here, and a list of supported touchscreens will be displayed. This option doesn't affect the kernel. If unsure, say Y. if INPUT_TOUCHSCREEN config TOUCHSCREEN_ADS7846 tristate "ADS7846/TSC2046 and ADS7843 based touchscreens" depends on SPI_MASTER depends on HWMON = n || HWMON help Say Y here if you have a touchscreen interface using the ADS7846/TSC2046 or ADS7843 controller, and your board-specific setup code includes that in its table of SPI devices. If HWMON is selected, and the driver is told the reference voltage on your board, you will also get hwmon interfaces for the voltage (and on ads7846/tsc2046, temperature) sensors of this chip. If unsure, say N (but it's safe to say "Y"). To compile this driver as a module, choose M here: the module will be called ads7846. config TOUCHSCREEN_BITSY tristate "Compaq iPAQ H3600 (Bitsy) touchscreen" depends on SA1100_BITSY select SERIO help Say Y here if you have the h3600 (Bitsy) touchscreen. If unsure, say N. To compile this driver as a module, choose M here: the module will be called h3600_ts_input. config TOUCHSCREEN_CORGI tristate "SharpSL (Corgi and Spitz series) touchscreen driver" depends on PXA_SHARPSL default y help Say Y here to enable the driver for the touchscreen on the Sharp SL-C7xx and SL-Cxx00 series of PDAs. If unsure, say N. To compile this driver as a module, choose M here: the module will be called corgi_ts. config TOUCHSCREEN_FUJITSU tristate "Fujitsu serial touchscreen" select SERIO help Say Y here if you have the Fujitsu touchscreen (such as one installed in Lifebook P series laptop) connected to your system. If unsure, say N. To compile this driver as a module, choose M here: the module will be called fujitsu-ts. config TOUCHSCREEN_GUNZE tristate "Gunze AHL-51S touchscreen" select SERIO help Say Y here if you have the Gunze AHL-51 touchscreen connected to your system. If unsure, say N. To compile this driver as a module, choose M here: the module will be called gunze. config TOUCHSCREEN_ELO tristate "Elo serial touchscreens" select SERIO help Say Y here if you have an Elo serial touchscreen connected to your system. If unsure, say N. To compile this driver as a module, choose M here: the module will be called elo. config TOUCHSCREEN_MTOUCH tristate "MicroTouch serial touchscreens" select SERIO help Say Y here if you have a MicroTouch (3M) serial touchscreen connected to your system. If unsure, say N. To compile this driver as a module, choose M here: the module will be called mtouch. config TOUCHSCREEN_INEXIO tristate "iNexio serial touchscreens" select SERIO help Say Y here if you have an iNexio serial touchscreen connected to your system. If unsure, say N. To compile this driver as a module, choose M here: the module will be called inexio. config TOUCHSCREEN_MK712 tristate "ICS MicroClock MK712 touchscreen" help Say Y here if you have the ICS MicroClock MK712 touchscreen controller chip in your system. If unsure, say N. To compile this driver as a module, choose M here: the module will be called mk712. config TOUCHSCREEN_HP600 tristate "HP Jornada 6xx touchscreen" depends on SH_HP6XX && SH_ADC help Say Y here if you have a HP Jornada 620/660/680/690 and want to support the built-in touchscreen. To compile this driver as a module, choose M here: the module will be called hp680_ts_input. config TOUCHSCREEN_HP7XX tristate "HP Jornada 7xx touchscreen" depends on SA1100_JORNADA720_SSP help Say Y here if you have a HP Jornada 710/720/728 and want to support the built-in touchscreen. To compile this driver as a module, choose M here: the module will be called jornada720_ts. config TOUCHSCREEN_HTCPEN tristate "HTC Shift X9500 touchscreen" depends on ISA help Say Y here if you have an HTC Shift UMPC also known as HTC X9500 Clio / Shangrila and want to support the built-in touchscreen. If unsure, say N. To compile this driver as a module, choose M here: the module will be called htcpen. config TOUCHSCREEN_PENMOUNT tristate "Penmount serial touchscreen" select SERIO help Say Y here if you have a Penmount serial touchscreen connected to your system. If unsure, say N. To compile this driver as a module, choose M here: the module will be called penmount. config TOUCHSCREEN_MIGOR tristate "Renesas MIGO-R touchscreen" depends on SH_MIGOR && I2C help Say Y here to enable MIGO-R touchscreen support. If unsure, say N. To compile this driver as a module, choose M here: the module will be called migor_ts. config TOUCHSCREEN_TOUCHRIGHT tristate "Touchright serial touchscreen" select SERIO help Say Y here if you have a Touchright serial touchscreen connected to your system. If unsure, say N. To compile this driver as a module, choose M here: the module will be called touchright. config TOUCHSCREEN_TOUCHWIN tristate "Touchwin serial touchscreen" select SERIO help Say Y here if you have a Touchwin serial touchscreen connected to your system. If unsure, say N. To compile this driver as a module, choose M here: the module will be called touchwin. config TOUCHSCREEN_ATMEL_TSADCC tristate "Atmel Touchscreen Interface" depends on ARCH_AT91SAM9RL help Say Y here if you have a 4-wire touchscreen connected to the ADC Controller on your Atmel SoC (such as the AT91SAM9RL). If unsure, say N. To compile this driver as a module, choose M here: the module will be called atmel_tsadcc. config TOUCHSCREEN_TSC2005 tristate "TSC2005 touchscreen support" help Say Y here for if you are using the touchscreen features of TSC2301. config TOUCHSCREEN_TSC2102 tristate "TSC 2102 based touchscreens" depends on SPI_MASTER select SPI_TSC2102 help Say Y here if you have a touchscreen interface using the TI TSC 2102 controller, and your board-specific initialization code includes that in its table of SPI devices. Also make sure the proper SPI controller is selected. If unsure, say N (but it's safe to say "Y"). To compile this driver as a module, choose M here: the module will be called tsc2102_ts. config TOUCHSCREEN_TSC210X tristate "TI TSC210x based touchscreens" depends on SPI_MASTER select SPI_TSC210X help Say Y here if you have a touchscreen interface using a TI TSC210x controller, and your board-specific initialisation code includes that in its table of SPI devices. If unsure, say N (but it's safe to say "Y"). To compile this driver as a module, choose M here: the module will be called tsc210x_ts. config TOUCHSCREEN_TSC2301 tristate "TSC2301 touchscreen support" depends on SPI_TSC2301 help Say Y here for if you are using the touchscreen features of TSC2301. config TOUCHSCREEN_UCB1400 tristate "Philips UCB1400 touchscreen" select AC97_BUS help This enables support for the Philips UCB1400 touchscreen interface. The UCB1400 is an AC97 audio codec. The touchscreen interface will be initialized only after the ALSA subsystem has been brought up and the UCB1400 detected. You therefore have to configure ALSA support as well (either built-in or modular, independently of whether this driver is itself built-in or modular) for this driver to work. To compile this driver as a module, choose M here: the module will be called ucb1400_ts. config TOUCHSCREEN_WM97XX tristate "Support for WM97xx AC97 touchscreen controllers" depends on AC97_BUS help Say Y here if you have a Wolfson Microelectronics WM97xx touchscreen connected to your system. Note that this option only enables core driver, you will also need to select support for appropriate chip below. If unsure, say N. To compile this driver as a module, choose M here: the module will be called wm97xx-ts. config TOUCHSCREEN_WM9705 bool "WM9705 Touchscreen interface support" depends on TOUCHSCREEN_WM97XX help Say Y here if you have a Wolfson Microelectronics WM9705 touchscreen controller connected to your system. If unsure, say N. config TOUCHSCREEN_WM9712 bool "WM9712 Touchscreen interface support" depends on TOUCHSCREEN_WM97XX help Say Y here if you have a Wolfson Microelectronics WM9712 touchscreen controller connected to your system. If unsure, say N. config TOUCHSCREEN_WM9713 bool "WM9713 Touchscreen interface support" depends on TOUCHSCREEN_WM97XX help Say Y here if you have a Wolfson Microelectronics WM9713 touchscreen controller connected to your system. If unsure, say N. config TOUCHSCREEN_WM97XX_MAINSTONE tristate "WM97xx Mainstone accelerated touch" depends on TOUCHSCREEN_WM97XX && ARCH_PXA help Say Y here for support for streaming mode with WM97xx touchscreens on Mainstone systems. If unsure, say N. To compile this driver as a module, choose M here: the module will be called mainstone-wm97xx. config TOUCHSCREEN_USB_COMPOSITE tristate "USB Touchscreen Driver" depends on USB_ARCH_HAS_HCD select USB help USB Touchscreen driver for: - eGalax Touchkit USB (also includes eTurboTouch CT-410/510/700) - PanJit TouchSet USB - 3M MicroTouch USB (EX II series) - ITM - some other eTurboTouch - Gunze AHL61 - DMC TSC-10/25 - IRTOUCHSYSTEMS/UNITOP - IdealTEK URTC1000 - GoTop Super_Q2/GogoPen/PenPower tablets Have a look at for a usage description and the required user-space stuff. To compile this driver as a module, choose M here: the module will be called usbtouchscreen. config TOUCHSCREEN_USB_EGALAX default y bool "eGalax, eTurboTouch CT-410/510/700 device support" if EMBEDDED depends on TOUCHSCREEN_USB_COMPOSITE config TOUCHSCREEN_USB_PANJIT default y bool "PanJit device support" if EMBEDDED depends on TOUCHSCREEN_USB_COMPOSITE config TOUCHSCREEN_USB_3M default y bool "3M/Microtouch EX II series device support" if EMBEDDED depends on TOUCHSCREEN_USB_COMPOSITE config TOUCHSCREEN_USB_ITM default y bool "ITM device support" if EMBEDDED depends on TOUCHSCREEN_USB_COMPOSITE config TOUCHSCREEN_USB_ETURBO default y bool "eTurboTouch (non-eGalax compatible) device support" if EMBEDDED depends on TOUCHSCREEN_USB_COMPOSITE config TOUCHSCREEN_USB_GUNZE default y bool "Gunze AHL61 device support" if EMBEDDED depends on TOUCHSCREEN_USB_COMPOSITE config TOUCHSCREEN_USB_DMC_TSC10 default y bool "DMC TSC-10/25 device support" if EMBEDDED depends on TOUCHSCREEN_USB_COMPOSITE config TOUCHSCREEN_USB_IRTOUCH default y bool "IRTOUCHSYSTEMS/UNITOP device support" if EMBEDDED depends on TOUCHSCREEN_USB_COMPOSITE config TOUCHSCREEN_USB_IDEALTEK default y bool "IdealTEK URTC1000 device support" if EMBEDDED depends on TOUCHSCREEN_USB_COMPOSITE config TOUCHSCREEN_USB_GENERAL_TOUCH default y bool "GeneralTouch Touchscreen device support" if EMBEDDED depends on TOUCHSCREEN_USB_COMPOSITE config TOUCHSCREEN_USB_GOTOP default y bool "GoTop Super_Q2/GogoPen/PenPower tablet device support" if EMBEDDED depends on TOUCHSCREEN_USB_COMPOSITE config TOUCHSCREEN_TOUCHIT213 tristate "Sahara TouchIT-213 touchscreen" select SERIO help Say Y here if you have a Sahara TouchIT-213 Tablet PC. If unsure, say N. To compile this driver as a module, choose M here: the module will be called touchit213. endif