STMicroelectronics 10/100/1000 Synopsys Ethernet driver Copyright (C) 2007-2010 STMicroelectronics Ltd Author: Giuseppe Cavallaro This is the driver for the MAC 10/100/1000 on-chip Ethernet controllers (Synopsys IP blocks); it has been fully tested on STLinux platforms. Currently this network device driver is for all STM embedded MAC/GMAC (7xxx SoCs). Other platforms start using it i.e. ARM SPEAr. DWC Ether MAC 10/100/1000 Universal version 3.41a and DWC Ether MAC 10/100 Universal version 4.0 have been used for developing the first code implementation. Please, for more information also visit: www.stlinux.com 1) Kernel Configuration The kernel configuration option is STMMAC_ETH: Device Drivers ---> Network device support ---> Ethernet (1000 Mbit) ---> STMicroelectronics 10/100/1000 Ethernet driver (STMMAC_ETH) 2) Driver parameters list: debug: message level (0: no output, 16: all); phyaddr: to manually provide the physical address to the PHY device; dma_rxsize: DMA rx ring size; dma_txsize: DMA tx ring size; buf_sz: DMA buffer size; tc: control the HW FIFO threshold; tx_coe: Enable/Disable Tx Checksum Offload engine; watchdog: transmit timeout (in milliseconds); flow_ctrl: Flow control ability [on/off]; pause: Flow Control Pause Time; tmrate: timer period (only if timer optimisation is configured). 3) Command line options Driver parameters can be also passed in command line by using: stmmaceth=dma_rxsize:128,dma_txsize:512 4) Driver information and notes 4.1) Transmit process The xmit method is invoked when the kernel needs to transmit a packet; it sets the descriptors in the ring and informs the DMA engine that there is a packet ready to be transmitted. Once the controller has finished transmitting the packet, an interrupt is triggered; So the driver will be able to release the socket buffers. By default, the driver sets the NETIF_F_SG bit in the features field of the net_device structure enabling the scatter/gather feature. 4.2) Receive process When one or more packets are received, an interrupt happens. The interrupts are not queued so the driver has to scan all the descriptors in the ring during the receive process. This is based on NAPI so the interrupt handler signals only if there is work to be done, and it exits. Then the poll method will be scheduled at some future point. The incoming packets are stored, by the DMA, in a list of pre-allocated socket buffers in order to avoid the memcpy (Zero-copy). 4.3) Timer-Driver Interrupt Instead of having the device that asynchronously notifies the frame receptions, the driver configures a timer to generate an interrupt at regular intervals. Based on the granularity of the timer, the frames that are received by the device will experience different levels of latency. Some NICs have dedicated timer device to perform this task. STMMAC can use either the RTC device or the TMU channel 2 on STLinux platforms. The timers frequency can be passed to the driver as parameter; when change it, take care of both hardware capability and network stability/performance impact. Several performance tests on STM platforms showed this optimisation allows to spare the CPU while having the maximum throughput. 4.4) WOL Wake up on Lan feature through Magic Frame is only supported for the GMAC core. 4.5) DMA descriptors Driver handles both normal and enhanced descriptors. The latter has been only tested on DWC Ether MAC 10/100/1000 Universal version 3.41a. 4.6) Ethtool support Ethtool is supported. Driver statistics and internal errors can be taken using: ethtool -S ethX command. It is possible to dump registers etc. 4.7) Jumbo and Segmentation Offloading Jumbo frames are supported and tested for the GMAC. The GSO has been also added but it's performed in software. LRO is not supported. 4.8) Physical The driver is compatible with PAL to work with PHY and GPHY devices. 4.9) Platform information Several information came from the platform; please refer to the driver's Header file in include/linux directory. struct plat_stmmacenet_data { int bus_id; int pbl; int clk_csr; int has_gmac; int enh_desc; int tx_coe; int bugged_jumbo; int pmt; void (*fix_mac_speed)(void *priv, unsigned int speed); void (*bus_setup)(unsigned long ioaddr); #ifdef CONFIG_STM_DRIVERS struct stm_pad_config *pad_config; #endif void *bsp_priv; }; Where: - pbl (Programmable Burst Length) is maximum number of beats to be transferred in one DMA transaction. GMAC also enables the 4xPBL by default. - fix_mac_speed and bus_setup are used to configure internal target registers (on STM platforms); - has_gmac: GMAC core is on board (get it at run-time in the next step); - bus_id: bus identifier. - tx_coe: core is able to perform the tx csum in HW. - enh_desc: if sets the MAC will use the enhanced descriptor structure. - clk_csr: CSR Clock range selection. - bugged_jumbo: some HWs are not able to perform the csum in HW for over-sized frames due to limited buffer sizes. Setting this flag the csum will be done in SW on JUMBO frames. struct plat_stmmacphy_data { int bus_id; int phy_addr; unsigned int phy_mask; int interface; int (*phy_reset)(void *priv); void *priv; }; Where: - bus_id: bus identifier; - phy_addr: physical address used for the attached phy device; set it to -1 to get it at run-time; - interface: physical MII interface mode; - phy_reset: hook to reset HW function. SOURCES: - Kconfig - Makefile - stmmac_main.c: main network device driver; - stmmac_mdio.c: mdio functions; - stmmac_ethtool.c: ethtool support; - stmmac_timer.[ch]: timer code used for mitigating the driver dma interrupts Only tested on ST40 platforms based. - stmmac.h: private driver structure; - common.h: common definitions and VFTs; - descs.h: descriptor structure definitions; - dwmac1000_core.c: GMAC core functions; - dwmac1000_dma.c: dma functions for the GMAC chip; - dwmac1000.h: specific header file for the GMAC; - dwmac100_core: MAC 100 core and dma code; - dwmac100_dma.c: dma funtions for the MAC chip; - dwmac1000.h: specific header file for the MAC; - dwmac_lib.c: generic DMA functions shared among chips - enh_desc.c: functions for handling enhanced descriptors - norm_desc.c: functions for handling normal descriptors TODO: - XGMAC controller is not supported. - Review the timer optimisation code to use an embedded device that seems to be available in new chip generations.