drivers/usb/host/ehci-hcd.c

   1 /*
   2  * Enhanced Host Controller Interface (EHCI) driver for USB.
   3  *
   4  * Maintainer: Alan Stern <stern@rowland.harvard.edu>
   5  *
   6  * Copyright (c) 2000-2004 by David Brownell
   7  *
   8  * This program is free software; you can redistribute it and/or modify it
   9  * under the terms of the GNU General Public License as published by the
  10  * Free Software Foundation; either version 2 of the License, or (at your
  11  * option) any later version.
  12  *
  13  * This program is distributed in the hope that it will be useful, but
  14  * WITHOUT ANY WARRANTY; without even the implied warranty of MERCHANTABILITY
  15  * or FITNESS FOR A PARTICULAR PURPOSE.  See the GNU General Public License
  16  * for more details.
  17  *
  18  * You should have received a copy of the GNU General Public License
  19  * along with this program; if not, write to the Free Software Foundation,
  20  * Inc., 675 Mass Ave, Cambridge, MA 02139, USA.
  21  */
  22
  23 #include <linux/module.h>
  24 #include <linux/pci.h>
  25 #include <linux/dmapool.h>
  26 #include <linux/kernel.h>
  27 #include <linux/delay.h>
  28 #include <linux/ioport.h>
  29 #include <linux/sched.h>
  30 #include <linux/vmalloc.h>
  31 #include <linux/errno.h>
  32 #include <linux/init.h>
  33 #include <linux/timer.h>
  34 #include <linux/ktime.h>
  35 #include <linux/list.h>
  36 #include <linux/interrupt.h>
  37 #include <linux/usb.h>
  38 #include <linux/usb/hcd.h>
  39 #include <linux/moduleparam.h>
  40 #include <linux/dma-mapping.h>
  41 #include <linux/debugfs.h>
  42 #include <linux/slab.h>
  43 #include <linux/uaccess.h>
  44
  45 #include <asm/byteorder.h>
  46 #include <asm/io.h>
  47 #include <asm/irq.h>
  48 #include <asm/system.h>
  49 #include <asm/unaligned.h>
  50
  51 /*-------------------------------------------------------------------------*/
  52
  53 /*
  54  * EHCI hc_driver implementation ... experimental, incomplete.
  55  * Based on the final 1.0 register interface specification.
  56  *
  57  * USB 2.0 shows up in upcoming www.pcmcia.org technology.
  58  * First was PCMCIA, like ISA; then CardBus, which is PCI.
  59  * Next comes "CardBay", using USB 2.0 signals.
  60  *
  61  * Contains additional contributions by Brad Hards, Rory Bolt, and others.
  62  * Special thanks to Intel and VIA for providing host controllers to
  63  * test this driver on, and Cypress (including In-System Design) for
  64  * providing early devices for those host controllers to talk to!
  65  */
  66
  67 #define DRIVER_AUTHOR "David Brownell"
  68 #define DRIVER_DESC "USB 2.0 'Enhanced' Host Controller (EHCI) Driver"
  69
  70 static const char       hcd_name [] = "ehci_hcd";
  71
  72
  73 #undef VERBOSE_DEBUG
  74 #undef EHCI_URB_TRACE
  75
  76 #ifdef DEBUG
  77 #define EHCI_STATS
  78 #endif
  79
  80 /* magic numbers that can affect system performance */
  81 #define EHCI_TUNE_CERR          3       /* 0-3 qtd retries; 0 == don't stop */
  82 #define EHCI_TUNE_RL_HS         4       /* nak throttle; see 4.9 */
  83 #define EHCI_TUNE_RL_TT         0
  84 #define EHCI_TUNE_MULT_HS       1       /* 1-3 transactions/uframe; 4.10.3 */
  85 #define EHCI_TUNE_MULT_TT       1
  86 /*
  87  * Some drivers think it's safe to schedule isochronous transfers more than
  88  * 256 ms into the future (partly as a result of an old bug in the scheduling
  89  * code).  In an attempt to avoid trouble, we will use a minimum scheduling
  90  * length of 512 frames instead of 256.
  91  */
  92 #define EHCI_TUNE_FLS           1       /* (medium) 512-frame schedule */
  93
  94 #define EHCI_IAA_MSECS          10              /* arbitrary */
  95 #define EHCI_IO_JIFFIES         (HZ/10)         /* io watchdog > irq_thresh */
  96 #define EHCI_ASYNC_JIFFIES      (HZ/20)         /* async idle timeout */
  97 #define EHCI_SHRINK_JIFFIES     (DIV_ROUND_UP(HZ, 200) + 1)
  98                                                 /* 200-ms async qh unlink delay */
  99
 100 /* Initial IRQ latency:  faster than hw default */
 101 static int log2_irq_thresh = 0;         // 0 to 6
 102 module_param (log2_irq_thresh, int, S_IRUGO);
 103 MODULE_PARM_DESC (log2_irq_thresh, "log2 IRQ latency, 1-64 microframes");
 104
 105 /* initial park setting:  slower than hw default */
 106 static unsigned park = 0;
 107 module_param (park, uint, S_IRUGO);
 108 MODULE_PARM_DESC (park, "park setting; 1-3 back-to-back async packets");
 109
 110 /* for flakey hardware, ignore overcurrent indicators */
 111 static int ignore_oc = 0;
 112 module_param (ignore_oc, bool, S_IRUGO);
 113 MODULE_PARM_DESC (ignore_oc, "ignore bogus hardware overcurrent indications");
 114
 115 /* for link power management(LPM) feature */
 116 static unsigned int hird;
 117 module_param(hird, int, S_IRUGO);
 118 MODULE_PARM_DESC(hird, "host initiated resume duration, +1 for each 75us");
 119
 120 #define INTR_MASK (STS_IAA | STS_FATAL | STS_PCD | STS_ERR | STS_INT)
 121
 122 /*-------------------------------------------------------------------------*/
 123
 124 #include "ehci.h"
 125 #include "ehci-dbg.c"
 126 #include "pci-quirks.h"
 127
 128 /*-------------------------------------------------------------------------*/
 129
 130 static void
 131 timer_action(struct ehci_hcd *ehci, enum ehci_timer_action action)
 132 {
 133         /* Don't override timeouts which shrink or (later) disable
 134          * the async ring; just the I/O watchdog.  Note that if a
 135          * SHRINK were pending, OFF would never be requested.
 136          */
 137         if (timer_pending(&ehci->watchdog)
 138                         && ((BIT(TIMER_ASYNC_SHRINK) | BIT(TIMER_ASYNC_OFF))
 139                                 & ehci->actions))
 140                 return;
 141
 142         if (!test_and_set_bit(action, &ehci->actions)) {
 143                 unsigned long t;
 144
 145                 switch (action) {
 146                 case TIMER_IO_WATCHDOG:
 147                         if (!ehci->need_io_watchdog)
 148                                 return;
 149                         t = EHCI_IO_JIFFIES;
 150                         break;
 151                 case TIMER_ASYNC_OFF:
 152                         t = EHCI_ASYNC_JIFFIES;
 153                         break;
 154                 /* case TIMER_ASYNC_SHRINK: */
 155                 default:
 156                         t = EHCI_SHRINK_JIFFIES;
 157                         break;
 158                 }
 159                 mod_timer(&ehci->watchdog, t + jiffies);
 160         }
 161 }
 162
 163 /*-------------------------------------------------------------------------*/
 164
 165 /*
 166  * handshake - spin reading hc until handshake completes or fails
 167  * @ptr: address of hc register to be read
 168  * @mask: bits to look at in result of read
 169  * @done: value of those bits when handshake succeeds
 170  * @usec: timeout in microseconds
 171  *
 172  * Returns negative errno, or zero on success
 173  *
 174  * Success happens when the "mask" bits have the specified value (hardware
 175  * handshake done).  There are two failure modes:  "usec" have passed (major
 176  * hardware flakeout), or the register reads as all-ones (hardware removed).
 177  *
 178  * That last failure should_only happen in cases like physical cardbus eject
 179  * before driver shutdown. But it also seems to be caused by bugs in cardbus
 180  * bridge shutdown:  shutting down the bridge before the devices using it.
 181  */
 182 static int handshake (struct ehci_hcd *ehci, void __iomem *ptr,
 183                       u32 mask, u32 done, int usec)
 184 {
 185         u32     result;
 186
 187         do {
 188                 result = ehci_readl(ehci, ptr);
 189                 if (result == ~(u32)0)          /* card removed */
 190                         return -ENODEV;
 191                 result &= mask;
 192                 if (result == done)
 193                         return 0;
 194                 udelay (1);
 195                 usec--;
 196         } while (usec > 0);
 197         return -ETIMEDOUT;
 198 }
 199
 200 /* check TDI/ARC silicon is in host mode */
 201 static int tdi_in_host_mode (struct ehci_hcd *ehci)
 202 {
 203         u32 __iomem     *reg_ptr;
 204         u32             tmp;
 205
 206         reg_ptr = (u32 __iomem *)(((u8 __iomem *)ehci->regs) + USBMODE);
 207         tmp = ehci_readl(ehci, reg_ptr);
 208         return (tmp & 3) == USBMODE_CM_HC;
 209 }
 210
 211 /* force HC to halt state from unknown (EHCI spec section 2.3) */
 212 static int ehci_halt (struct ehci_hcd *ehci)
 213 {
 214         u32     temp = ehci_readl(ehci, &ehci->regs->status);
 215
 216         /* disable any irqs left enabled by previous code */
 217         ehci_writel(ehci, 0, &ehci->regs->intr_enable);
 218
 219         if (ehci_is_TDI(ehci) && tdi_in_host_mode(ehci) == 0) {
 220                 return 0;
 221         }
 222
 223         if ((temp & STS_HALT) != 0)
 224                 return 0;
 225
 226         temp = ehci_readl(ehci, &ehci->regs->command);
 227         temp &= ~CMD_RUN;
 228         ehci_writel(ehci, temp, &ehci->regs->command);
 229         return handshake (ehci, &ehci->regs->status,
 230                           STS_HALT, STS_HALT, 16 * 125);
 231 }
 232
 233 static int handshake_on_error_set_halt(struct ehci_hcd *ehci, void __iomem *ptr,
 234                                        u32 mask, u32 done, int usec)
 235 {
 236         int error;
 237
 238         error = handshake(ehci, ptr, mask, done, usec);
 239         if (error) {
 240                 ehci_halt(ehci);
 241                 ehci_to_hcd(ehci)->state = HC_STATE_HALT;
 242                 ehci_err(ehci, "force halt; handshake %p %08x %08x -> %d\n",
 243                         ptr, mask, done, error);
 244         }
 245
 246         return error;
 247 }
 248
 249 /* put TDI/ARC silicon into EHCI mode */
 250 static void tdi_reset (struct ehci_hcd *ehci)
 251 {
 252         u32 __iomem     *reg_ptr;
 253         u32             tmp;
 254
 255         reg_ptr = (u32 __iomem *)(((u8 __iomem *)ehci->regs) + USBMODE);
 256         tmp = ehci_readl(ehci, reg_ptr);
 257         tmp |= USBMODE_CM_HC;
 258         /* The default byte access to MMR space is LE after
 259          * controller reset. Set the required endian mode
 260          * for transfer buffers to match the host microprocessor
 261          */
 262         if (ehci_big_endian_mmio(ehci))
 263                 tmp |= USBMODE_BE;
 264         ehci_writel(ehci, tmp, reg_ptr);
 265 }
 266
 267 /* reset a non-running (STS_HALT == 1) controller */
 268 static int ehci_reset (struct ehci_hcd *ehci)
 269 {
 270         int     retval;
 271         u32     command = ehci_readl(ehci, &ehci->regs->command);
 272
 273         /* If the EHCI debug controller is active, special care must be
 274          * taken before and after a host controller reset */
 275         if (ehci->debug && !dbgp_reset_prep())
 276                 ehci->debug = NULL;
 277
 278         command |= CMD_RESET;
 279         dbg_cmd (ehci, "reset", command);
 280         ehci_writel(ehci, command, &ehci->regs->command);
 281         ehci_to_hcd(ehci)->state = HC_STATE_HALT;
 282         ehci->next_statechange = jiffies;
 283         retval = handshake (ehci, &ehci->regs->command,
 284                             CMD_RESET, 0, 250 * 1000);
 285
 286         if (ehci->has_hostpc) {
 287                 ehci_writel(ehci, USBMODE_EX_HC | USBMODE_EX_VBPS,
 288                         (u32 __iomem *)(((u8 *)ehci->regs) + USBMODE_EX));
 289                 ehci_writel(ehci, TXFIFO_DEFAULT,
 290                         (u32 __iomem *)(((u8 *)ehci->regs) + TXFILLTUNING));
 291         }
 292         if (retval)
 293                 return retval;
 294
 295         if (ehci_is_TDI(ehci))
 296                 tdi_reset (ehci);
 297
 298         if (ehci->debug)
 299                 dbgp_external_startup();
 300
 301         return retval;
 302 }
 303
 304 /* idle the controller (from running) */
 305 static void ehci_quiesce (struct ehci_hcd *ehci)
 306 {
 307         u32     temp;
 308
 309 #ifdef DEBUG
 310         if (!HC_IS_RUNNING (ehci_to_hcd(ehci)->state))
 311                 BUG ();
 312 #endif
 313
 314         /* wait for any schedule enables/disables to take effect */
 315         temp = ehci_readl(ehci, &ehci->regs->command) << 10;
 316         temp &= STS_ASS | STS_PSS;
 317         if (handshake_on_error_set_halt(ehci, &ehci->regs->status,
 318                                         STS_ASS | STS_PSS, temp, 16 * 125))
 319                 return;
 320
 321         /* then disable anything that's still active */
 322         temp = ehci_readl(ehci, &ehci->regs->command);
 323         temp &= ~(CMD_ASE | CMD_IAAD | CMD_PSE);
 324         ehci_writel(ehci, temp, &ehci->regs->command);
 325
 326         /* hardware can take 16 microframes to turn off ... */
 327         handshake_on_error_set_halt(ehci, &ehci->regs->status,
 328                                     STS_ASS | STS_PSS, 0, 16 * 125);
 329 }
 330
 331 /*-------------------------------------------------------------------------*/
 332
 333 static void end_unlink_async(struct ehci_hcd *ehci);
 334 static void ehci_work(struct ehci_hcd *ehci);
 335
 336 #include "ehci-hub.c"
 337 #include "ehci-lpm.c"
 338 #include "ehci-mem.c"
 339 #include "ehci-q.c"
 340 #include "ehci-sched.c"
 341 #include "ehci-sysfs.c"
 342
 343 /*-------------------------------------------------------------------------*/
 344
 345 static void ehci_iaa_watchdog(unsigned long param)
 346 {
 347         struct ehci_hcd         *ehci = (struct ehci_hcd *) param;
 348         unsigned long           flags;
 349
 350         spin_lock_irqsave (&ehci->lock, flags);
 351
 352         /* Lost IAA irqs wedge things badly; seen first with a vt8235.
 353          * So we need this watchdog, but must protect it against both
 354          * (a) SMP races against real IAA firing and retriggering, and
 355          * (b) clean HC shutdown, when IAA watchdog was pending.
 356          */
 357         if (ehci->reclaim
 358                         && !timer_pending(&ehci->iaa_watchdog)
 359                         && HC_IS_RUNNING(ehci_to_hcd(ehci)->state)) {
 360                 u32 cmd, status;
 361
 362                 /* If we get here, IAA is *REALLY* late.  It's barely
 363                  * conceivable that the system is so busy that CMD_IAAD
 364                  * is still legitimately set, so let's be sure it's
 365                  * clear before we read STS_IAA.  (The HC should clear
 366                  * CMD_IAAD when it sets STS_IAA.)
 367                  */
 368                 cmd = ehci_readl(ehci, &ehci->regs->command);
 369                 if (cmd & CMD_IAAD)
 370                         ehci_writel(ehci, cmd & ~CMD_IAAD,
 371                                         &ehci->regs->command);
 372
 373                 /* If IAA is set here it either legitimately triggered
 374                  * before we cleared IAAD above (but _way_ late, so we'll
 375                  * still count it as lost) ... or a silicon erratum:
 376                  * - VIA seems to set IAA without triggering the IRQ;
 377                  * - IAAD potentially cleared without setting IAA.
 378                  */
 379                 status = ehci_readl(ehci, &ehci->regs->status);
 380                 if ((status & STS_IAA) || !(cmd & CMD_IAAD)) {
 381                         COUNT (ehci->stats.lost_iaa);
 382                         ehci_writel(ehci, STS_IAA, &ehci->regs->status);
 383                 }
 384
 385                 ehci_vdbg(ehci, "IAA watchdog: status %x cmd %x\n",
 386                                 status, cmd);
 387                 end_unlink_async(ehci);
 388         }
 389
 390         spin_unlock_irqrestore(&ehci->lock, flags);
 391 }
 392
 393 static void ehci_watchdog(unsigned long param)
 394 {
 395         struct ehci_hcd         *ehci = (struct ehci_hcd *) param;
 396         unsigned long           flags;
 397
 398         spin_lock_irqsave(&ehci->lock, flags);
 399
 400         /* stop async processing after it's idled a bit */
 401         if (test_bit (TIMER_ASYNC_OFF, &ehci->actions))
 402                 start_unlink_async (ehci, ehci->async);
 403
 404         /* ehci could run by timer, without IRQs ... */
 405         ehci_work (ehci);
 406
 407         spin_unlock_irqrestore (&ehci->lock, flags);
 408 }
 409
 410 /* On some systems, leaving remote wakeup enabled prevents system shutdown.
 411  * The firmware seems to think that powering off is a wakeup event!
 412  * This routine turns off remote wakeup and everything else, on all ports.
 413  */
 414 static void ehci_turn_off_all_ports(struct ehci_hcd *ehci)
 415 {
 416         int     port = HCS_N_PORTS(ehci->hcs_params);
 417
 418         while (port--)
 419                 ehci_writel(ehci, PORT_RWC_BITS,
 420                                 &ehci->regs->port_status[port]);
 421 }
 422
 423 /*
 424  * Halt HC, turn off all ports, and let the BIOS use the companion controllers.
 425  * Should be called with ehci->lock held.
 426  */
 427 static void ehci_silence_controller(struct ehci_hcd *ehci)
 428 {
 429         ehci_halt(ehci);
 430         ehci_turn_off_all_ports(ehci);
 431
 432         /* make BIOS/etc use companion controller during reboot */
 433         ehci_writel(ehci, 0, &ehci->regs->configured_flag);
 434
 435         /* unblock posted writes */
 436         ehci_readl(ehci, &ehci->regs->configured_flag);
 437 }
 438
 439 /* ehci_shutdown kick in for silicon on any bus (not just pci, etc).
 440  * This forcibly disables dma and IRQs, helping kexec and other cases
 441  * where the next system software may expect clean state.
 442  */
 443 static void ehci_shutdown(struct usb_hcd *hcd)
 444 {
 445         struct ehci_hcd *ehci = hcd_to_ehci(hcd);
 446
 447         del_timer_sync(&ehci->watchdog);
 448         del_timer_sync(&ehci->iaa_watchdog);
 449
 450         spin_lock_irq(&ehci->lock);
 451         ehci_silence_controller(ehci);
 452         spin_unlock_irq(&ehci->lock);
 453 }
 454
 455 static void ehci_port_power (struct ehci_hcd *ehci, int is_on)
 456 {
 457         unsigned port;
 458
 459         if (!HCS_PPC (ehci->hcs_params))
 460                 return;
 461
 462         ehci_dbg (ehci, "...power%s ports...\n", is_on ? "up" : "down");
 463         for (port = HCS_N_PORTS (ehci->hcs_params); port > 0; )
 464                 (void) ehci_hub_control(ehci_to_hcd(ehci),
 465                                 is_on ? SetPortFeature : ClearPortFeature,
 466                                 USB_PORT_FEAT_POWER,
 467                                 port--, NULL, 0);
 468         /* Flush those writes */
 469         ehci_readl(ehci, &ehci->regs->command);
 470         msleep(20);
 471 }
 472
 473 /*-------------------------------------------------------------------------*/
 474
 475 /*
 476  * ehci_work is called from some interrupts, timers, and so on.
 477  * it calls driver completion functions, after dropping ehci->lock.
 478  */
 479 static void ehci_work (struct ehci_hcd *ehci)
 480 {
 481         timer_action_done (ehci, TIMER_IO_WATCHDOG);
 482
 483         /* another CPU may drop ehci->lock during a schedule scan while
 484          * it reports urb completions.  this flag guards against bogus
 485          * attempts at re-entrant schedule scanning.
 486          */
 487         if (ehci->scanning)
 488                 return;
 489         ehci->scanning = 1;
 490         scan_async (ehci);
 491         if (ehci->next_uframe != -1)
 492                 scan_periodic (ehci);
 493         ehci->scanning = 0;
 494
 495         /* the IO watchdog guards against hardware or driver bugs that
 496          * misplace IRQs, and should let us run completely without IRQs.
 497          * such lossage has been observed on both VT6202 and VT8235.
 498          */
 499         if (HC_IS_RUNNING (ehci_to_hcd(ehci)->state) &&
 500                         (ehci->async->qh_next.ptr != NULL ||
 501                          ehci->periodic_sched != 0))
 502                 timer_action (ehci, TIMER_IO_WATCHDOG);
 503 }
 504
 505 /*
 506  * Called when the ehci_hcd module is removed.
 507  */
 508 static void ehci_stop (struct usb_hcd *hcd)
 509 {
 510         struct ehci_hcd         *ehci = hcd_to_ehci (hcd);
 511
 512         ehci_dbg (ehci, "stop\n");
 513
 514         /* no more interrupts ... */
 515         del_timer_sync (&ehci->watchdog);
 516         del_timer_sync(&ehci->iaa_watchdog);
 517
 518         spin_lock_irq(&ehci->lock);
 519         if (HC_IS_RUNNING (hcd->state))
 520                 ehci_quiesce (ehci);
 521
 522         ehci_silence_controller(ehci);
 523         ehci_reset (ehci);
 524         spin_unlock_irq(&ehci->lock);
 525
 526         remove_sysfs_files(ehci);
 527         remove_debug_files (ehci);
 528
 529         /* root hub is shut down separately (first, when possible) */
 530         spin_lock_irq (&ehci->lock);
 531         if (ehci->async)
 532                 ehci_work (ehci);
 533         spin_unlock_irq (&ehci->lock);
 534         ehci_mem_cleanup (ehci);
 535
 536         if (ehci->amd_pll_fix == 1)
 537                 usb_amd_dev_put();
 538
 539 #ifdef  EHCI_STATS
 540         ehci_dbg (ehci, "irq normal %ld err %ld reclaim %ld (lost %ld)\n",
 541                 ehci->stats.normal, ehci->stats.error, ehci->stats.reclaim,
 542                 ehci->stats.lost_iaa);
 543         ehci_dbg (ehci, "complete %ld unlink %ld\n",
 544                 ehci->stats.complete, ehci->stats.unlink);
 545 #endif
 546
 547         dbg_status (ehci, "ehci_stop completed",
 548                     ehci_readl(ehci, &ehci->regs->status));
 549 }
 550
 551 /* one-time init, only for memory state */
 552 static int ehci_init(struct usb_hcd *hcd)
 553 {
 554         struct ehci_hcd         *ehci = hcd_to_ehci(hcd);
 555         u32                     temp;
 556         int                     retval;
 557         u32                     hcc_params;
 558         struct ehci_qh_hw       *hw;
 559
 560         spin_lock_init(&ehci->lock);
 561
 562         /*
 563          * keep io watchdog by default, those good HCDs could turn off it later
 564          */
 565         ehci->need_io_watchdog = 1;
 566         init_timer(&ehci->watchdog);
 567         ehci->watchdog.function = ehci_watchdog;
 568         ehci->watchdog.data = (unsigned long) ehci;
 569
 570         init_timer(&ehci->iaa_watchdog);
 571         ehci->iaa_watchdog.function = ehci_iaa_watchdog;
 572         ehci->iaa_watchdog.data = (unsigned long) ehci;
 573
 574         hcc_params = ehci_readl(ehci, &ehci->caps->hcc_params);
 575
 576         /*
 577          * by default set standard 80% (== 100 usec/uframe) max periodic
 578          * bandwidth as required by USB 2.0
 579          */
 580         ehci->uframe_periodic_max = 100;
 581
 582         /*
 583          * hw default: 1K periodic list heads, one per frame.
 584          * periodic_size can shrink by USBCMD update if hcc_params allows.
 585          */
 586         ehci->periodic_size = DEFAULT_I_TDPS;
 587         INIT_LIST_HEAD(&ehci->cached_itd_list);
 588         INIT_LIST_HEAD(&ehci->cached_sitd_list);
 589
 590         if (HCC_PGM_FRAMELISTLEN(hcc_params)) {
 591                 /* periodic schedule size can be smaller than default */
 592                 switch (EHCI_TUNE_FLS) {
 593                 case 0: ehci->periodic_size = 1024; break;
 594                 case 1: ehci->periodic_size = 512; break;
 595                 case 2: ehci->periodic_size = 256; break;
 596                 default:        BUG();
 597                 }
 598         }
 599         if ((retval = ehci_mem_init(ehci, GFP_KERNEL)) < 0)
 600                 return retval;
 601
 602         /* controllers may cache some of the periodic schedule ... */
 603         if (HCC_ISOC_CACHE(hcc_params))         // full frame cache
 604                 ehci->i_thresh = 2 + 8;
 605         else                                    // N microframes cached
 606                 ehci->i_thresh = 2 + HCC_ISOC_THRES(hcc_params);
 607
 608         ehci->reclaim = NULL;
 609         ehci->next_uframe = -1;
 610         ehci->clock_frame = -1;
 611
 612         /*
 613          * dedicate a qh for the async ring head, since we couldn't unlink
 614          * a 'real' qh without stopping the async schedule [4.8].  use it
 615          * as the 'reclamation list head' too.
 616          * its dummy is used in hw_alt_next of many tds, to prevent the qh
 617          * from automatically advancing to the next td after short reads.
 618          */
 619         ehci->async->qh_next.qh = NULL;
 620         hw = ehci->async->hw;
 621         hw->hw_next = QH_NEXT(ehci, ehci->async->qh_dma);
 622         hw->hw_info1 = cpu_to_hc32(ehci, QH_HEAD);
 623         hw->hw_token = cpu_to_hc32(ehci, QTD_STS_HALT);
 624         hw->hw_qtd_next = EHCI_LIST_END(ehci);
 625         ehci->async->qh_state = QH_STATE_LINKED;
 626         hw->hw_alt_next = QTD_NEXT(ehci, ehci->async->dummy->qtd_dma);
 627
 628         /* clear interrupt enables, set irq latency */
 629         if (log2_irq_thresh < 0 || log2_irq_thresh > 6)
 630                 log2_irq_thresh = 0;
 631         temp = 1 << (16 + log2_irq_thresh);
 632         if (HCC_PER_PORT_CHANGE_EVENT(hcc_params)) {
 633                 ehci->has_ppcd = 1;
 634                 ehci_dbg(ehci, "enable per-port change event\n");
 635                 temp |= CMD_PPCEE;
 636         }
 637         if (HCC_CANPARK(hcc_params)) {
 638                 /* HW default park == 3, on hardware that supports it (like
 639                  * NVidia and ALI silicon), maximizes throughput on the async
 640                  * schedule by avoiding QH fetches between transfers.
 641                  *
 642                  * With fast usb storage devices and NForce2, "park" seems to
 643                  * make problems:  throughput reduction (!), data errors...
 644                  */
 645                 if (park) {
 646                         park = min(park, (unsigned) 3);
 647                         temp |= CMD_PARK;
 648                         temp |= park << 8;
 649                 }
 650                 ehci_dbg(ehci, "park %d\n", park);
 651         }
 652         if (HCC_PGM_FRAMELISTLEN(hcc_params)) {
 653                 /* periodic schedule size can be smaller than default */
 654                 temp &= ~(3 << 2);
 655                 temp |= (EHCI_TUNE_FLS << 2);
 656         }
 657         if (HCC_LPM(hcc_params)) {
 658                 /* support link power management EHCI 1.1 addendum */
 659                 ehci_dbg(ehci, "support lpm\n");
 660                 ehci->has_lpm = 1;
 661                 if (hird > 0xf) {
 662                         ehci_dbg(ehci, "hird %d invalid, use default 0",
 663                         hird);
 664                         hird = 0;
 665                 }
 666                 temp |= hird << 24;
 667         }
 668         ehci->command = temp;
 669
 670         /* Accept arbitrarily long scatter-gather lists */
 671         if (!(hcd->driver->flags & HCD_LOCAL_MEM))
 672                 hcd->self.sg_tablesize = ~0;
 673         return 0;
 674 }
 675
 676 /* start HC running; it's halted, ehci_init() has been run (once) */
 677 static int ehci_run (struct usb_hcd *hcd)
 678 {
 679         struct ehci_hcd         *ehci = hcd_to_ehci (hcd);
 680         int                     retval;
 681         u32                     temp;
 682         u32                     hcc_params;
 683
 684         hcd->uses_new_polling = 1;
 685
 686         /* EHCI spec section 4.1 */
 687         /*
 688          * TDI driver does the ehci_reset in their reset callback.
 689          * Don't reset here, because configuration settings will
 690          * vanish.
 691          */
 692         if (!ehci_is_TDI(ehci) && (retval = ehci_reset(ehci)) != 0) {
 693                 ehci_mem_cleanup(ehci);
 694                 return retval;
 695         }
 696         ehci_writel(ehci, ehci->periodic_dma, &ehci->regs->frame_list);
 697         ehci_writel(ehci, (u32)ehci->async->qh_dma, &ehci->regs->async_next);
 698
 699         /*
 700          * hcc_params controls whether ehci->regs->segment must (!!!)
 701          * be used; it constrains QH/ITD/SITD and QTD locations.
 702          * pci_pool consistent memory always uses segment zero.
 703          * streaming mappings for I/O buffers, like pci_map_single(),
 704          * can return segments above 4GB, if the device allows.
 705          *
 706          * NOTE:  the dma mask is visible through dma_supported(), so
 707          * drivers can pass this info along ... like NETIF_F_HIGHDMA,
 708          * Scsi_Host.highmem_io, and so forth.  It's readonly to all
 709          * host side drivers though.
 710          */
 711         hcc_params = ehci_readl(ehci, &ehci->caps->hcc_params);
 712         if (HCC_64BIT_ADDR(hcc_params)) {
 713                 ehci_writel(ehci, 0, &ehci->regs->segment);
 714 #if 0
 715 // this is deeply broken on almost all architectures
 716                 if (!dma_set_mask(hcd->self.controller, DMA_BIT_MASK(64)))
 717                         ehci_info(ehci, "enabled 64bit DMA\n");
 718 #endif
 719         }
 720
 721
 722         // Philips, Intel, and maybe others need CMD_RUN before the
 723         // root hub will detect new devices (why?); NEC doesn't
 724         ehci->command &= ~(CMD_LRESET|CMD_IAAD|CMD_PSE|CMD_ASE|CMD_RESET);
 725         ehci->command |= CMD_RUN;
 726         ehci_writel(ehci, ehci->command, &ehci->regs->command);
 727         dbg_cmd (ehci, "init", ehci->command);
 728
 729         /*
 730          * Start, enabling full USB 2.0 functionality ... usb 1.1 devices
 731          * are explicitly handed to companion controller(s), so no TT is
 732          * involved with the root hub.  (Except where one is integrated,
 733          * and there's no companion controller unless maybe for USB OTG.)
 734          *
 735          * Turning on the CF flag will transfer ownership of all ports
 736          * from the companions to the EHCI controller.  If any of the
 737          * companions are in the middle of a port reset at the time, it
 738          * could cause trouble.  Write-locking ehci_cf_port_reset_rwsem
 739          * guarantees that no resets are in progress.  After we set CF,
 740          * a short delay lets the hardware catch up; new resets shouldn't
 741          * be started before the port switching actions could complete.
 742          */
 743         down_write(&ehci_cf_port_reset_rwsem);
 744         hcd->state = HC_STATE_RUNNING;
 745         ehci_writel(ehci, FLAG_CF, &ehci->regs->configured_flag);
 746         ehci_readl(ehci, &ehci->regs->command); /* unblock posted writes */
 747         msleep(5);
 748         up_write(&ehci_cf_port_reset_rwsem);
 749         ehci->last_periodic_enable = ktime_get_real();
 750
 751         temp = HC_VERSION(ehci, ehci_readl(ehci, &ehci->caps->hc_capbase));
 752         ehci_info (ehci,
 753                 "USB %x.%x started, EHCI %x.%02x%s\n",
 754                 ((ehci->sbrn & 0xf0)>>4), (ehci->sbrn & 0x0f),
 755                 temp >> 8, temp & 0xff,
 756                 ignore_oc ? ", overcurrent ignored" : "");
 757
 758         ehci_writel(ehci, INTR_MASK,
 759                     &ehci->regs->intr_enable); /* Turn On Interrupts */
 760
 761         /* GRR this is run-once init(), being done every time the HC starts.
 762          * So long as they're part of class devices, we can't do it init()
 763          * since the class device isn't created that early.
 764          */
 765         create_debug_files(ehci);
 766         create_sysfs_files(ehci);
 767
 768         return 0;
 769 }
 770
 771 /*-------------------------------------------------------------------------*/
 772
 773 static irqreturn_t ehci_irq (struct usb_hcd *hcd)
 774 {
 775         struct ehci_hcd         *ehci = hcd_to_ehci (hcd);
 776         u32                     status, masked_status, pcd_status = 0, cmd;
 777         int                     bh;
 778
 779         spin_lock (&ehci->lock);
 780
 781         status = ehci_readl(ehci, &ehci->regs->status);
 782
 783         /* e.g. cardbus physical eject */
 784         if (status == ~(u32) 0) {
 785                 ehci_dbg (ehci, "device removed\n");
 786                 goto dead;
 787         }
 788
 789         /* Shared IRQ? */
 790         masked_status = status & INTR_MASK;
 791         if (!masked_status || unlikely(hcd->state == HC_STATE_HALT)) {
 792                 spin_unlock(&ehci->lock);
 793                 return IRQ_NONE;
 794         }
 795
 796         /* clear (just) interrupts */
 797         ehci_writel(ehci, masked_status, &ehci->regs->status);
 798         cmd = ehci_readl(ehci, &ehci->regs->command);
 799         bh = 0;
 800
 801 #ifdef  VERBOSE_DEBUG
 802         /* unrequested/ignored: Frame List Rollover */
 803         dbg_status (ehci, "irq", status);
 804 #endif
 805
 806         /* INT, ERR, and IAA interrupt rates can be throttled */
 807
 808         /* normal [4.15.1.2] or error [4.15.1.1] completion */
 809         if (likely ((status & (STS_INT|STS_ERR)) != 0)) {
 810                 if (likely ((status & STS_ERR) == 0))
 811                         COUNT (ehci->stats.normal);
 812                 else
 813                         COUNT (ehci->stats.error);
 814                 bh = 1;
 815         }
 816
 817         /* complete the unlinking of some qh [4.15.2.3] */
 818         if (status & STS_IAA) {
 819                 /* guard against (alleged) silicon errata */
 820                 if (cmd & CMD_IAAD) {
 821                         ehci_writel(ehci, cmd & ~CMD_IAAD,
 822                                         &ehci->regs->command);
 823                         ehci_dbg(ehci, "IAA with IAAD still set?\n");
 824                 }
 825                 if (ehci->reclaim) {
 826                         COUNT(ehci->stats.reclaim);
 827                         end_unlink_async(ehci);
 828                 } else
 829                         ehci_dbg(ehci, "IAA with nothing to reclaim?\n");
 830         }
 831
 832         /* remote wakeup [4.3.1] */
 833         if (status & STS_PCD) {
 834                 unsigned        i = HCS_N_PORTS (ehci->hcs_params);
 835                 u32             ppcd = 0;
 836
 837                 /* kick root hub later */
 838                 pcd_status = status;
 839
 840                 /* resume root hub? */
 841                 if (!(cmd & CMD_RUN))
 842                         usb_hcd_resume_root_hub(hcd);
 843
 844                 /* get per-port change detect bits */
 845                 if (ehci->has_ppcd)
 846                         ppcd = status >> 16;
 847
 848                 while (i--) {
 849                         int pstatus;
 850
 851                         /* leverage per-port change bits feature */
 852                         if (ehci->has_ppcd && !(ppcd & (1 << i)))
 853                                 continue;
 854                         pstatus = ehci_readl(ehci,
 855                                          &ehci->regs->port_status[i]);
 856
 857                         if (pstatus & PORT_OWNER)
 858                                 continue;
 859                         if (!(test_bit(i, &ehci->suspended_ports) &&
 860                                         ((pstatus & PORT_RESUME) ||
 861                                                 !(pstatus & PORT_SUSPEND)) &&
 862                                         (pstatus & PORT_PE) &&
 863                                         ehci->reset_done[i] == 0))
 864                                 continue;
 865
 866                         /* start 20 msec resume signaling from this port,
 867                          * and make khubd collect PORT_STAT_C_SUSPEND to
 868                          * stop that signaling.  Use 5 ms extra for safety,
 869                          * like usb_port_resume() does.
 870                          */
 871                         ehci->reset_done[i] = jiffies + msecs_to_jiffies(25);
 872                         ehci_dbg (ehci, "port %d remote wakeup\n", i + 1);
 873                         mod_timer(&hcd->rh_timer, ehci->reset_done[i]);
 874                 }
 875         }
 876
 877         /* PCI errors [4.15.2.4] */
 878         if (unlikely ((status & STS_FATAL) != 0)) {
 879                 ehci_err(ehci, "fatal error\n");
 880                 dbg_cmd(ehci, "fatal", cmd);
 881                 dbg_status(ehci, "fatal", status);
 882                 ehci_halt(ehci);
 883 dead:
 884                 ehci_reset(ehci);
 885                 ehci_writel(ehci, 0, &ehci->regs->configured_flag);
 886                 usb_hc_died(hcd);
 887                 /* generic layer kills/unlinks all urbs, then
 888                  * uses ehci_stop to clean up the rest
 889                  */
 890                 bh = 1;
 891         }
 892
 893         if (bh)
 894                 ehci_work (ehci);
 895         spin_unlock (&ehci->lock);
 896         if (pcd_status)
 897                 usb_hcd_poll_rh_status(hcd);
 898         return IRQ_HANDLED;
 899 }
 900
 901 /*-------------------------------------------------------------------------*/
 902
 903 /*
 904  * non-error returns are a promise to giveback() the urb later
 905  * we drop ownership so next owner (or urb unlink) can get it
 906  *
 907  * urb + dev is in hcd.self.controller.urb_list
 908  * we're queueing TDs onto software and hardware lists
 909  *
 910  * hcd-specific init for hcpriv hasn't been done yet
 911  *
 912  * NOTE:  control, bulk, and interrupt share the same code to append TDs
 913  * to a (possibly active) QH, and the same QH scanning code.
 914  */
 915 static int ehci_urb_enqueue (
 916         struct usb_hcd  *hcd,
 917         struct urb      *urb,
 918         gfp_t           mem_flags
 919 ) {
 920         struct ehci_hcd         *ehci = hcd_to_ehci (hcd);
 921         struct list_head        qtd_list;
 922
 923         INIT_LIST_HEAD (&qtd_list);
 924
 925         switch (usb_pipetype (urb->pipe)) {
 926         case PIPE_CONTROL:
 927                 /* qh_completions() code doesn't handle all the fault cases
 928                  * in multi-TD control transfers.  Even 1KB is rare anyway.
 929                  */
 930                 if (urb->transfer_buffer_length > (16 * 1024))
 931                         return -EMSGSIZE;
 932                 /* FALLTHROUGH */
 933         /* case PIPE_BULK: */
 934         default:
 935                 if (!qh_urb_transaction (ehci, urb, &qtd_list, mem_flags))
 936                         return -ENOMEM;
 937                 return submit_async(ehci, urb, &qtd_list, mem_flags);
 938
 939         case PIPE_INTERRUPT:
 940                 if (!qh_urb_transaction (ehci, urb, &qtd_list, mem_flags))
 941                         return -ENOMEM;
 942                 return intr_submit(ehci, urb, &qtd_list, mem_flags);
 943
 944         case PIPE_ISOCHRONOUS:
 945                 if (urb->dev->speed == USB_SPEED_HIGH)
 946                         return itd_submit (ehci, urb, mem_flags);
 947                 else
 948                         return sitd_submit (ehci, urb, mem_flags);
 949         }
 950 }
 951
 952 static void unlink_async (struct ehci_hcd *ehci, struct ehci_qh *qh)
 953 {
 954         /* failfast */
 955         if (!HC_IS_RUNNING(ehci_to_hcd(ehci)->state) && ehci->reclaim)
 956                 end_unlink_async(ehci);
 957
 958         /* If the QH isn't linked then there's nothing we can do
 959          * unless we were called during a giveback, in which case
 960          * qh_completions() has to deal with it.
 961          */
 962         if (qh->qh_state != QH_STATE_LINKED) {
 963                 if (qh->qh_state == QH_STATE_COMPLETING)
 964                         qh->needs_rescan = 1;
 965                 return;
 966         }
 967
 968         /* defer till later if busy */
 969         if (ehci->reclaim) {
 970                 struct ehci_qh          *last;
 971
 972                 for (last = ehci->reclaim;
 973                                 last->reclaim;
 974                                 last = last->reclaim)
 975                         continue;
 976                 qh->qh_state = QH_STATE_UNLINK_WAIT;
 977                 last->reclaim = qh;
 978
 979         /* start IAA cycle */
 980         } else
 981                 start_unlink_async (ehci, qh);
 982 }
 983
 984 /* remove from hardware lists
 985  * completions normally happen asynchronously
 986  */
 987
 988 static int ehci_urb_dequeue(struct usb_hcd *hcd, struct urb *urb, int status)
 989 {
 990         struct ehci_hcd         *ehci = hcd_to_ehci (hcd);
 991         struct ehci_qh          *qh;
 992         unsigned long           flags;
 993         int                     rc;
 994
 995         spin_lock_irqsave (&ehci->lock, flags);
 996         rc = usb_hcd_check_unlink_urb(hcd, urb, status);
 997         if (rc)
 998                 goto done;
 999
1000         switch (usb_pipetype (urb->pipe)) {
1001         // case PIPE_CONTROL:
1002         // case PIPE_BULK:
1003         default:
1004                 qh = (struct ehci_qh *) urb->hcpriv;
1005                 if (!qh)
1006                         break;
1007                 switch (qh->qh_state) {
1008                 case QH_STATE_LINKED:
1009                 case QH_STATE_COMPLETING:
1010                         unlink_async(ehci, qh);
1011                         break;
1012                 case QH_STATE_UNLINK:
1013                 case QH_STATE_UNLINK_WAIT:
1014                         /* already started */
1015                         break;
1016                 case QH_STATE_IDLE:
1017                         /* QH might be waiting for a Clear-TT-Buffer */
1018                         qh_completions(ehci, qh);
1019                         break;
1020                 }
1021                 break;
1022
1023         case PIPE_INTERRUPT:
1024                 qh = (struct ehci_qh *) urb->hcpriv;
1025                 if (!qh)
1026                         break;
1027                 switch (qh->qh_state) {
1028                 case QH_STATE_LINKED:
1029                 case QH_STATE_COMPLETING:
1030                         intr_deschedule (ehci, qh);
1031                         break;
1032                 case QH_STATE_IDLE:
1033                         qh_completions (ehci, qh);
1034                         break;
1035                 default:
1036                         ehci_dbg (ehci, "bogus qh %p state %d\n",
1037                                         qh, qh->qh_state);
1038                         goto done;
1039                 }
1040                 break;
1041
1042         case PIPE_ISOCHRONOUS:
1043                 // itd or sitd ...
1044
1045                 // wait till next completion, do it then.
1046                 // completion irqs can wait up to 1024 msec,
1047                 break;
1048         }
1049 done:
1050         spin_unlock_irqrestore (&ehci->lock, flags);
1051         return rc;
1052 }
1053
1054 /*-------------------------------------------------------------------------*/
1055
1056 // bulk qh holds the data toggle
1057
1058 static void
1059 ehci_endpoint_disable (struct usb_hcd *hcd, struct usb_host_endpoint *ep)
1060 {
1061         struct ehci_hcd         *ehci = hcd_to_ehci (hcd);
1062         unsigned long           flags;
1063         struct ehci_qh          *qh, *tmp;
1064
1065         /* ASSERT:  any requests/urbs are being unlinked */
1066         /* ASSERT:  nobody can be submitting urbs for this any more */
1067
1068 rescan:
1069         spin_lock_irqsave (&ehci->lock, flags);
1070         qh = ep->hcpriv;
1071         if (!qh)
1072                 goto done;
1073
1074         /* endpoints can be iso streams.  for now, we don't
1075          * accelerate iso completions ... so spin a while.
1076          */
1077         if (qh->hw == NULL) {
1078                 ehci_vdbg (ehci, "iso delay\n");
1079                 goto idle_timeout;
1080         }
1081
1082         if (!HC_IS_RUNNING (hcd->state))
1083                 qh->qh_state = QH_STATE_IDLE;
1084         switch (qh->qh_state) {
1085         case QH_STATE_LINKED:
1086         case QH_STATE_COMPLETING:
1087                 for (tmp = ehci->async->qh_next.qh;
1088                                 tmp && tmp != qh;
1089                                 tmp = tmp->qh_next.qh)
1090                         continue;
1091                 /* periodic qh self-unlinks on empty, and a COMPLETING qh
1092                  * may already be unlinked.
1093                  */
1094                 if (tmp)
1095                         unlink_async(ehci, qh);
1096                 /* FALL THROUGH */
1097         case QH_STATE_UNLINK:           /* wait for hw to finish? */
1098         case QH_STATE_UNLINK_WAIT:
1099 idle_timeout:
1100                 spin_unlock_irqrestore (&ehci->lock, flags);
1101                 schedule_timeout_uninterruptible(1);
1102                 goto rescan;
1103         case QH_STATE_IDLE:             /* fully unlinked */
1104                 if (qh->clearing_tt)
1105                         goto idle_timeout;
1106                 if (list_empty (&qh->qtd_list)) {
1107                         qh_put (qh);
1108                         break;
1109                 }
1110                 /* else FALL THROUGH */
1111         default:
1112                 /* caller was supposed to have unlinked any requests;
1113                  * that's not our job.  just leak this memory.
1114                  */
1115                 ehci_err (ehci, "qh %p (#%02x) state %d%s\n",
1116                         qh, ep->desc.bEndpointAddress, qh->qh_state,
1117                         list_empty (&qh->qtd_list) ? "" : "(has tds)");
1118                 break;
1119         }
1120         ep->hcpriv = NULL;
1121 done:
1122         spin_unlock_irqrestore (&ehci->lock, flags);
1123 }
1124
1125 static void
1126 ehci_endpoint_reset(struct usb_hcd *hcd, struct usb_host_endpoint *ep)
1127 {
1128         struct ehci_hcd         *ehci = hcd_to_ehci(hcd);
1129         struct ehci_qh          *qh;
1130         int                     eptype = usb_endpoint_type(&ep->desc);
1131         int                     epnum = usb_endpoint_num(&ep->desc);
1132         int                     is_out = usb_endpoint_dir_out(&ep->desc);
1133         unsigned long           flags;
1134
1135         if (eptype != USB_ENDPOINT_XFER_BULK && eptype != USB_ENDPOINT_XFER_INT)
1136                 return;
1137
1138         spin_lock_irqsave(&ehci->lock, flags);
1139         qh = ep->hcpriv;
1140
1141         /* For Bulk and Interrupt endpoints we maintain the toggle state
1142          * in the hardware; the toggle bits in udev aren't used at all.
1143          * When an endpoint is reset by usb_clear_halt() we must reset
1144          * the toggle bit in the QH.
1145          */
1146         if (qh) {
1147                 usb_settoggle(qh->dev, epnum, is_out, 0);
1148                 if (!list_empty(&qh->qtd_list)) {
1149                         WARN_ONCE(1, "clear_halt for a busy endpoint\n");
1150                 } else if (qh->qh_state == QH_STATE_LINKED ||
1151                                 qh->qh_state == QH_STATE_COMPLETING) {
1152
1153                         /* The toggle value in the QH can't be updated
1154                          * while the QH is active.  Unlink it now;
1155                          * re-linking will call qh_refresh().
1156                          */
1157                         if (eptype == USB_ENDPOINT_XFER_BULK)
1158                                 unlink_async(ehci, qh);
1159                         else
1160                                 intr_deschedule(ehci, qh);
1161                 }
1162         }
1163         spin_unlock_irqrestore(&ehci->lock, flags);
1164 }
1165
1166 static int ehci_get_frame (struct usb_hcd *hcd)
1167 {
1168         struct ehci_hcd         *ehci = hcd_to_ehci (hcd);
1169         return (ehci_readl(ehci, &ehci->regs->frame_index) >> 3) %
1170                 ehci->periodic_size;
1171 }
1172
1173 /*-------------------------------------------------------------------------*/
1174
1175 MODULE_DESCRIPTION(DRIVER_DESC);
1176 MODULE_AUTHOR (DRIVER_AUTHOR);
1177 MODULE_LICENSE ("GPL");
1178
1179 #ifdef CONFIG_PCI
1180 #include "ehci-pci.c"
1181 #define PCI_DRIVER              ehci_pci_driver
1182 #endif
1183
1184 #ifdef CONFIG_USB_EHCI_FSL
1185 #include "ehci-fsl.c"
1186 #define PLATFORM_DRIVER         ehci_fsl_driver
1187 #endif
1188
1189 #ifdef CONFIG_USB_EHCI_MXC
1190 #include "ehci-mxc.c"
1191 #define PLATFORM_DRIVER         ehci_mxc_driver
1192 #endif
1193
1194 #ifdef CONFIG_USB_EHCI_SH
1195 #include "ehci-sh.c"
1196 #define PLATFORM_DRIVER         ehci_hcd_sh_driver
1197 #endif
1198
1199 #ifdef CONFIG_SOC_AU1200
1200 #include "ehci-au1xxx.c"
1201 #define PLATFORM_DRIVER         ehci_hcd_au1xxx_driver
1202 #endif
1203
1204 #ifdef CONFIG_USB_EHCI_HCD_OMAP
1205 #include "ehci-omap.c"
1206 #define        PLATFORM_DRIVER         ehci_hcd_omap_driver
1207 #endif
1208
1209 #ifdef CONFIG_PPC_PS3
1210 #include "ehci-ps3.c"
1211 #define PS3_SYSTEM_BUS_DRIVER   ps3_ehci_driver
1212 #endif
1213
1214 #ifdef CONFIG_USB_EHCI_HCD_PPC_OF
1215 #include "ehci-ppc-of.c"
1216 #define OF_PLATFORM_DRIVER      ehci_hcd_ppc_of_driver
1217 #endif
1218
1219 #ifdef CONFIG_XPS_USB_HCD_XILINX
1220 #include "ehci-xilinx-of.c"
1221 #define XILINX_OF_PLATFORM_DRIVER       ehci_hcd_xilinx_of_driver
1222 #endif
1223
1224 #ifdef CONFIG_PLAT_ORION
1225 #include "ehci-orion.c"
1226 #define PLATFORM_DRIVER         ehci_orion_driver
1227 #endif
1228
1229 #ifdef CONFIG_ARCH_IXP4XX
1230 #include "ehci-ixp4xx.c"
1231 #define PLATFORM_DRIVER         ixp4xx_ehci_driver
1232 #endif
1233
1234 #ifdef CONFIG_USB_W90X900_EHCI
1235 #include "ehci-w90x900.c"
1236 #define PLATFORM_DRIVER         ehci_hcd_w90x900_driver
1237 #endif
1238
1239 #ifdef CONFIG_ARCH_AT91
1240 #include "ehci-atmel.c"
1241 #define PLATFORM_DRIVER         ehci_atmel_driver
1242 #endif
1243
1244 #ifdef CONFIG_USB_OCTEON_EHCI
1245 #include "ehci-octeon.c"
1246 #define PLATFORM_DRIVER         ehci_octeon_driver
1247 #endif
1248
1249 #ifdef CONFIG_USB_CNS3XXX_EHCI
1250 #include "ehci-cns3xxx.c"
1251 #define PLATFORM_DRIVER         cns3xxx_ehci_driver
1252 #endif
1253
1254 #ifdef CONFIG_ARCH_VT8500
1255 #include "ehci-vt8500.c"
1256 #define PLATFORM_DRIVER         vt8500_ehci_driver
1257 #endif
1258
1259 #ifdef CONFIG_PLAT_SPEAR
1260 #include "ehci-spear.c"
1261 #define PLATFORM_DRIVER         spear_ehci_hcd_driver
1262 #endif
1263
1264 #ifdef CONFIG_USB_EHCI_MSM
1265 #include "ehci-msm.c"
1266 #define PLATFORM_DRIVER         ehci_msm_driver
1267 #endif
1268
1269 #ifdef CONFIG_USB_EHCI_HCD_PMC_MSP
1270 #include "ehci-pmcmsp.c"
1271 #define PLATFORM_DRIVER         ehci_hcd_msp_driver
1272 #endif
1273
1274 #ifdef CONFIG_USB_EHCI_TEGRA
1275 #include "ehci-tegra.c"
1276 #define PLATFORM_DRIVER         tegra_ehci_driver
1277 #endif
1278
1279 #ifdef CONFIG_USB_EHCI_S5P
1280 #include "ehci-s5p.c"
1281 #define PLATFORM_DRIVER         s5p_ehci_driver
1282 #endif
1283
1284 #ifdef CONFIG_USB_EHCI_ATH79
1285 #include "ehci-ath79.c"
1286 #define PLATFORM_DRIVER         ehci_ath79_driver
1287 #endif
1288
1289 #ifdef CONFIG_SPARC_LEON
1290 #include "ehci-grlib.c"
1291 #define PLATFORM_DRIVER         ehci_grlib_driver
1292 #endif
1293
1294 #if !defined(PCI_DRIVER) && !defined(PLATFORM_DRIVER) && \
1295     !defined(PS3_SYSTEM_BUS_DRIVER) && !defined(OF_PLATFORM_DRIVER) && \
1296     !defined(XILINX_OF_PLATFORM_DRIVER)
1297 #error "missing bus glue for ehci-hcd"
1298 #endif
1299
1300 static int __init ehci_hcd_init(void)
1301 {
1302         int retval = 0;
1303
1304         if (usb_disabled())
1305                 return -ENODEV;
1306
1307         printk(KERN_INFO "%s: " DRIVER_DESC "\n", hcd_name);
1308         set_bit(USB_EHCI_LOADED, &usb_hcds_loaded);
1309         if (test_bit(USB_UHCI_LOADED, &usb_hcds_loaded) ||
1310                         test_bit(USB_OHCI_LOADED, &usb_hcds_loaded))
1311                 printk(KERN_WARNING "Warning! ehci_hcd should always be loaded"
1312                                 " before uhci_hcd and ohci_hcd, not after\n");
1313
1314         pr_debug("%s: block sizes: qh %Zd qtd %Zd itd %Zd sitd %Zd\n",
1315                  hcd_name,
1316                  sizeof(struct ehci_qh), sizeof(struct ehci_qtd),
1317                  sizeof(struct ehci_itd), sizeof(struct ehci_sitd));
1318
1319 #ifdef DEBUG
1320         ehci_debug_root = debugfs_create_dir("ehci", usb_debug_root);
1321         if (!ehci_debug_root) {
1322                 retval = -ENOENT;
1323                 goto err_debug;
1324         }
1325 #endif
1326
1327 #ifdef PLATFORM_DRIVER
1328         retval = platform_driver_register(&PLATFORM_DRIVER);
1329         if (retval < 0)
1330                 goto clean0;
1331 #endif
1332
1333 #ifdef PCI_DRIVER
1334         retval = pci_register_driver(&PCI_DRIVER);
1335         if (retval < 0)
1336                 goto clean1;
1337 #endif
1338
1339 #ifdef PS3_SYSTEM_BUS_DRIVER
1340         retval = ps3_ehci_driver_register(&PS3_SYSTEM_BUS_DRIVER);
1341         if (retval < 0)
1342                 goto clean2;
1343 #endif
1344
1345 #ifdef OF_PLATFORM_DRIVER
1346         retval = platform_driver_register(&OF_PLATFORM_DRIVER);
1347         if (retval < 0)
1348                 goto clean3;
1349 #endif
1350
1351 #ifdef XILINX_OF_PLATFORM_DRIVER
1352         retval = platform_driver_register(&XILINX_OF_PLATFORM_DRIVER);
1353         if (retval < 0)
1354                 goto clean4;
1355 #endif
1356         return retval;
1357
1358 #ifdef XILINX_OF_PLATFORM_DRIVER
1359         /* platform_driver_unregister(&XILINX_OF_PLATFORM_DRIVER); */
1360 clean4:
1361 #endif
1362 #ifdef OF_PLATFORM_DRIVER
1363         platform_driver_unregister(&OF_PLATFORM_DRIVER);
1364 clean3:
1365 #endif
1366 #ifdef PS3_SYSTEM_BUS_DRIVER
1367         ps3_ehci_driver_unregister(&PS3_SYSTEM_BUS_DRIVER);
1368 clean2:
1369 #endif
1370 #ifdef PCI_DRIVER
1371         pci_unregister_driver(&PCI_DRIVER);
1372 clean1:
1373 #endif
1374 #ifdef PLATFORM_DRIVER
1375         platform_driver_unregister(&PLATFORM_DRIVER);
1376 clean0:
1377 #endif
1378 #ifdef DEBUG
1379         debugfs_remove(ehci_debug_root);
1380         ehci_debug_root = NULL;
1381 err_debug:
1382 #endif
1383         clear_bit(USB_EHCI_LOADED, &usb_hcds_loaded);
1384         return retval;
1385 }
1386 module_init(ehci_hcd_init);
1387
1388 static void __exit ehci_hcd_cleanup(void)
1389 {
1390 #ifdef XILINX_OF_PLATFORM_DRIVER
1391         platform_driver_unregister(&XILINX_OF_PLATFORM_DRIVER);
1392 #endif
1393 #ifdef OF_PLATFORM_DRIVER
1394         platform_driver_unregister(&OF_PLATFORM_DRIVER);
1395 #endif
1396 #ifdef PLATFORM_DRIVER
1397         platform_driver_unregister(&PLATFORM_DRIVER);
1398 #endif
1399 #ifdef PCI_DRIVER
1400         pci_unregister_driver(&PCI_DRIVER);
1401 #endif
1402 #ifdef PS3_SYSTEM_BUS_DRIVER
1403         ps3_ehci_driver_unregister(&PS3_SYSTEM_BUS_DRIVER);
1404 #endif
1405 #ifdef DEBUG
1406         debugfs_remove(ehci_debug_root);
1407 #endif
1408         clear_bit(USB_EHCI_LOADED, &usb_hcds_loaded);
1409 }
1410 module_exit(ehci_hcd_cleanup);
1411