2 tristate "Atheros AR6003 support (non mac80211)"
7 This module adds support for wireless adapters based on Atheros AR6003 chipset running over SDIO. If you choose to build it as a module, it will be called ath6kl. Pls note that AR6002 and AR6001 are not supported by this driver.
10 prompt "AR6003 Board Data Configuration"
11 depends on ATH6K_LEGACY
12 default AR600x_SD31_XXX
14 Select the appropriate board data template from the list below that matches your AR6003 based reference design.
16 config AR600x_SD31_XXX
19 Board Data file for a standard SD31 reference design (File: bdata.SD31.bin)
21 config AR600x_WB31_XXX
24 Board Data file for a standard WB31 (BT/WiFi) reference design (File: bdata.WB31.bin)
26 config AR600x_SD32_XXX
29 Board Data file for a standard SD32 (5GHz) reference design (File: bdata.SD32.bin)
31 config AR600x_CUSTOM_XXX
34 Board Data file for a custom reference design (File: should be named as bdata.CUSTOM.bin)
37 config ATH6KL_ENABLE_COEXISTENCE
38 bool "BT Coexistence support"
39 depends on ATH6K_LEGACY
41 Enables WLAN/BT coexistence support. Select the apprpriate configuration from below.
44 prompt "Front-End Antenna Configuration"
45 depends on ATH6KL_ENABLE_COEXISTENCE
46 default AR600x_DUAL_ANTENNA
48 Indicates the number of antennas being used by BT and WLAN. Select the appropriate configuration from the list below that matches your AR6003 based reference design.
50 config AR600x_DUAL_ANTENNA
55 config AR600x_SINGLE_ANTENNA
62 prompt "Collocated Bluetooth Type"
63 depends on ATH6KL_ENABLE_COEXISTENCE
64 default AR600x_BT_AR3001
66 Select the appropriate configuration from the list below that matches your AR6003 based reference design.
69 bool "Qualcomm BTS4020X"
71 Qualcomm BT (3 Wire PTA)
78 config AR600x_BT_AR3001
81 Atheros BT (3 Wire PTA)
84 config ATH6KL_HCI_BRIDGE
85 bool "HCI over SDIO support"
86 depends on ATH6K_LEGACY
88 Enables BT over SDIO. Applicable only for combo designs (eg: WB31)
90 config ATH6KL_CONFIG_GPIO_BT_RESET
91 bool "Configure BT Reset GPIO"
92 depends on ATH6KL_HCI_BRIDGE
94 Configure a WLAN GPIO for use with BT.
96 config AR600x_BT_RESET_PIN
98 depends on ATH6KL_CONFIG_GPIO_BT_RESET
101 WLAN GPIO to be used for resetting BT
103 config ATH6KL_HTC_RAW_INTERFACE
104 bool "RAW HTC support"
105 depends on ATH6K_LEGACY
107 Enables raw HTC interface. Allows application to directly talk to the HTC interface via the ioctl interface
109 config ATH6KL_VIRTUAL_SCATTER_GATHER
110 bool "Virtual Scatter-Gather support"
111 depends on ATH6K_LEGACY
113 Enables virtual scatter gather support for the hardware that does not support it natively.
115 config ATH6KL_SKIP_ABI_VERSION_CHECK
116 bool "Skip ABI version check support"
117 depends on ATH6K_LEGACY
119 Forces the driver to disable ABI version check. Caution: Incompatilbity between the host driver and target firmware may lead to unknown side effects.
121 config ATH6KL_BT_UART_FC_POLARITY
122 int "UART Flow Control Polarity"
123 depends on ATH6KL_LEGACY
126 Configures the polarity of UART Flow Control. A value of 0 implies active low and is the default setting. Set it to 1 for active high.
130 depends on ATH6K_LEGACY
132 Enables debug support
134 config ATH6KL_ENABLE_HOST_DEBUG
135 bool "Host Debug support"
136 depends on ATH6KL_DEBUG
138 Enables debug support in the driver
140 config ATH6KL_ENABLE_TARGET_DEBUG_PRINTS
141 bool "Target Debug support - Enable UART prints"
142 depends on ATH6KL_DEBUG
146 config AR600x_DEBUG_UART_TX_PIN
148 depends on ATH6KL_ENABLE_TARGET_DEBUG_PRINTS
151 WLAN GPIO to be used for Debug UART (Tx)
153 config ATH6KL_DISABLE_TARGET_DBGLOGS
154 bool "Target Debug support - Disable Debug logs"
155 depends on ATH6KL_DEBUG