drivers/net/wireless/rtl818x/rtl8187_dev.c

   1 /*
   2  * Linux device driver for RTL8187
   3  *
   4  * Copyright 2007 Michael Wu <flamingice@sourmilk.net>
   5  * Copyright 2007 Andrea Merello <andreamrl@tiscali.it>
   6  *
   7  * Based on the r8187 driver, which is:
   8  * Copyright 2005 Andrea Merello <andreamrl@tiscali.it>, et al.
   9  *
  10  * The driver was extended to the RTL8187B in 2008 by:
  11  *      Herton Ronaldo Krzesinski <herton@mandriva.com.br>
  12  *      Hin-Tak Leung <htl10@users.sourceforge.net>
  13  *      Larry Finger <Larry.Finger@lwfinger.net>
  14  *
  15  * Magic delays and register offsets below are taken from the original
  16  * r8187 driver sources.  Thanks to Realtek for their support!
  17  *
  18  * This program is free software; you can redistribute it and/or modify
  19  * it under the terms of the GNU General Public License version 2 as
  20  * published by the Free Software Foundation.
  21  */
  22
  23 #include <linux/init.h>
  24 #include <linux/usb.h>
  25 #include <linux/delay.h>
  26 #include <linux/etherdevice.h>
  27 #include <linux/eeprom_93cx6.h>
  28 #include <net/mac80211.h>
  29
  30 #include "rtl8187.h"
  31 #include "rtl8187_rtl8225.h"
  32 #ifdef CONFIG_RTL8187_LEDS
  33 #include "rtl8187_leds.h"
  34 #endif
  35
  36 MODULE_AUTHOR("Michael Wu <flamingice@sourmilk.net>");
  37 MODULE_AUTHOR("Andrea Merello <andreamrl@tiscali.it>");
  38 MODULE_AUTHOR("Herton Ronaldo Krzesinski <herton@mandriva.com.br>");
  39 MODULE_AUTHOR("Hin-Tak Leung <htl10@users.sourceforge.net>");
  40 MODULE_AUTHOR("Larry Finger <Larry.Finger@lwfinger.net>");
  41 MODULE_DESCRIPTION("RTL8187/RTL8187B USB wireless driver");
  42 MODULE_LICENSE("GPL");
  43
  44 static struct usb_device_id rtl8187_table[] __devinitdata = {
  45         /* Asus */
  46         {USB_DEVICE(0x0b05, 0x171d), .driver_info = DEVICE_RTL8187},
  47         /* Belkin */
  48         {USB_DEVICE(0x050d, 0x705e), .driver_info = DEVICE_RTL8187B},
  49         /* Realtek */
  50         {USB_DEVICE(0x0bda, 0x8187), .driver_info = DEVICE_RTL8187},
  51         {USB_DEVICE(0x0bda, 0x8189), .driver_info = DEVICE_RTL8187B},
  52         {USB_DEVICE(0x0bda, 0x8197), .driver_info = DEVICE_RTL8187B},
  53         {USB_DEVICE(0x0bda, 0x8198), .driver_info = DEVICE_RTL8187B},
  54         /* Surecom */
  55         {USB_DEVICE(0x0769, 0x11F2), .driver_info = DEVICE_RTL8187},
  56         /* Logitech */
  57         {USB_DEVICE(0x0789, 0x010C), .driver_info = DEVICE_RTL8187},
  58         /* Netgear */
  59         {USB_DEVICE(0x0846, 0x6100), .driver_info = DEVICE_RTL8187},
  60         {USB_DEVICE(0x0846, 0x6a00), .driver_info = DEVICE_RTL8187},
  61         {USB_DEVICE(0x0846, 0x4260), .driver_info = DEVICE_RTL8187B},
  62         /* HP */
  63         {USB_DEVICE(0x03f0, 0xca02), .driver_info = DEVICE_RTL8187},
  64         /* Sitecom */
  65         {USB_DEVICE(0x0df6, 0x000d), .driver_info = DEVICE_RTL8187},
  66         {USB_DEVICE(0x0df6, 0x0028), .driver_info = DEVICE_RTL8187B},
  67         /* Sphairon Access Systems GmbH */
  68         {USB_DEVICE(0x114B, 0x0150), .driver_info = DEVICE_RTL8187},
  69         /* Dick Smith Electronics */
  70         {USB_DEVICE(0x1371, 0x9401), .driver_info = DEVICE_RTL8187},
  71         /* Abocom */
  72         {USB_DEVICE(0x13d1, 0xabe6), .driver_info = DEVICE_RTL8187},
  73         /* Qcom */
  74         {USB_DEVICE(0x18E8, 0x6232), .driver_info = DEVICE_RTL8187},
  75         /* AirLive */
  76         {USB_DEVICE(0x1b75, 0x8187), .driver_info = DEVICE_RTL8187},
  77         /* Linksys */
  78         {USB_DEVICE(0x1737, 0x0073), .driver_info = DEVICE_RTL8187B},
  79         {}
  80 };
  81
  82 MODULE_DEVICE_TABLE(usb, rtl8187_table);
  83
  84 static const struct ieee80211_rate rtl818x_rates[] = {
  85         { .bitrate = 10, .hw_value = 0, },
  86         { .bitrate = 20, .hw_value = 1, },
  87         { .bitrate = 55, .hw_value = 2, },
  88         { .bitrate = 110, .hw_value = 3, },
  89         { .bitrate = 60, .hw_value = 4, },
  90         { .bitrate = 90, .hw_value = 5, },
  91         { .bitrate = 120, .hw_value = 6, },
  92         { .bitrate = 180, .hw_value = 7, },
  93         { .bitrate = 240, .hw_value = 8, },
  94         { .bitrate = 360, .hw_value = 9, },
  95         { .bitrate = 480, .hw_value = 10, },
  96         { .bitrate = 540, .hw_value = 11, },
  97 };
  98
  99 static const struct ieee80211_channel rtl818x_channels[] = {
 100         { .center_freq = 2412 },
 101         { .center_freq = 2417 },
 102         { .center_freq = 2422 },
 103         { .center_freq = 2427 },
 104         { .center_freq = 2432 },
 105         { .center_freq = 2437 },
 106         { .center_freq = 2442 },
 107         { .center_freq = 2447 },
 108         { .center_freq = 2452 },
 109         { .center_freq = 2457 },
 110         { .center_freq = 2462 },
 111         { .center_freq = 2467 },
 112         { .center_freq = 2472 },
 113         { .center_freq = 2484 },
 114 };
 115
 116 static void rtl8187_iowrite_async_cb(struct urb *urb)
 117 {
 118         kfree(urb->context);
 119 }
 120
 121 static void rtl8187_iowrite_async(struct rtl8187_priv *priv, __le16 addr,
 122                                   void *data, u16 len)
 123 {
 124         struct usb_ctrlrequest *dr;
 125         struct urb *urb;
 126         struct rtl8187_async_write_data {
 127                 u8 data[4];
 128                 struct usb_ctrlrequest dr;
 129         } *buf;
 130         int rc;
 131
 132         buf = kmalloc(sizeof(*buf), GFP_ATOMIC);
 133         if (!buf)
 134                 return;
 135
 136         urb = usb_alloc_urb(0, GFP_ATOMIC);
 137         if (!urb) {
 138                 kfree(buf);
 139                 return;
 140         }
 141
 142         dr = &buf->dr;
 143
 144         dr->bRequestType = RTL8187_REQT_WRITE;
 145         dr->bRequest = RTL8187_REQ_SET_REG;
 146         dr->wValue = addr;
 147         dr->wIndex = 0;
 148         dr->wLength = cpu_to_le16(len);
 149
 150         memcpy(buf, data, len);
 151
 152         usb_fill_control_urb(urb, priv->udev, usb_sndctrlpipe(priv->udev, 0),
 153                              (unsigned char *)dr, buf, len,
 154                              rtl8187_iowrite_async_cb, buf);
 155         usb_anchor_urb(urb, &priv->anchored);
 156         rc = usb_submit_urb(urb, GFP_ATOMIC);
 157         if (rc < 0) {
 158                 kfree(buf);
 159                 usb_unanchor_urb(urb);
 160         }
 161         usb_free_urb(urb);
 162 }
 163
 164 static inline void rtl818x_iowrite32_async(struct rtl8187_priv *priv,
 165                                            __le32 *addr, u32 val)
 166 {
 167         __le32 buf = cpu_to_le32(val);
 168
 169         rtl8187_iowrite_async(priv, cpu_to_le16((unsigned long)addr),
 170                               &buf, sizeof(buf));
 171 }
 172
 173 void rtl8187_write_phy(struct ieee80211_hw *dev, u8 addr, u32 data)
 174 {
 175         struct rtl8187_priv *priv = dev->priv;
 176
 177         data <<= 8;
 178         data |= addr | 0x80;
 179
 180         rtl818x_iowrite8(priv, &priv->map->PHY[3], (data >> 24) & 0xFF);
 181         rtl818x_iowrite8(priv, &priv->map->PHY[2], (data >> 16) & 0xFF);
 182         rtl818x_iowrite8(priv, &priv->map->PHY[1], (data >> 8) & 0xFF);
 183         rtl818x_iowrite8(priv, &priv->map->PHY[0], data & 0xFF);
 184 }
 185
 186 static void rtl8187_tx_cb(struct urb *urb)
 187 {
 188         struct sk_buff *skb = (struct sk_buff *)urb->context;
 189         struct ieee80211_tx_info *info = IEEE80211_SKB_CB(skb);
 190         struct ieee80211_hw *hw = info->rate_driver_data[0];
 191         struct rtl8187_priv *priv = hw->priv;
 192
 193         skb_pull(skb, priv->is_rtl8187b ? sizeof(struct rtl8187b_tx_hdr) :
 194                                           sizeof(struct rtl8187_tx_hdr));
 195         ieee80211_tx_info_clear_status(info);
 196
 197         if (!(urb->status) && !(info->flags & IEEE80211_TX_CTL_NO_ACK)) {
 198                 if (priv->is_rtl8187b) {
 199                         skb_queue_tail(&priv->b_tx_status.queue, skb);
 200
 201                         /* queue is "full", discard last items */
 202                         while (skb_queue_len(&priv->b_tx_status.queue) > 5) {
 203                                 struct sk_buff *old_skb;
 204
 205                                 dev_dbg(&priv->udev->dev,
 206                                         "transmit status queue full\n");
 207
 208                                 old_skb = skb_dequeue(&priv->b_tx_status.queue);
 209                                 ieee80211_tx_status_irqsafe(hw, old_skb);
 210                         }
 211                         return;
 212                 } else {
 213                         info->flags |= IEEE80211_TX_STAT_ACK;
 214                 }
 215         }
 216         if (priv->is_rtl8187b)
 217                 ieee80211_tx_status_irqsafe(hw, skb);
 218         else {
 219                 /* Retry information for the RTI8187 is only available by
 220                  * reading a register in the device. We are in interrupt mode
 221                  * here, thus queue the skb and finish on a work queue. */
 222                 skb_queue_tail(&priv->b_tx_status.queue, skb);
 223                 queue_delayed_work(hw->workqueue, &priv->work, 0);
 224         }
 225 }
 226
 227 static int rtl8187_tx(struct ieee80211_hw *dev, struct sk_buff *skb)
 228 {
 229         struct rtl8187_priv *priv = dev->priv;
 230         struct ieee80211_tx_info *info = IEEE80211_SKB_CB(skb);
 231         unsigned int ep;
 232         void *buf;
 233         struct urb *urb;
 234         __le16 rts_dur = 0;
 235         u32 flags;
 236         int rc;
 237
 238         urb = usb_alloc_urb(0, GFP_ATOMIC);
 239         if (!urb) {
 240                 kfree_skb(skb);
 241                 return NETDEV_TX_OK;
 242         }
 243
 244         flags = skb->len;
 245         flags |= RTL818X_TX_DESC_FLAG_NO_ENC;
 246
 247         flags |= ieee80211_get_tx_rate(dev, info)->hw_value << 24;
 248         if (ieee80211_has_morefrags(((struct ieee80211_hdr *)skb->data)->frame_control))
 249                 flags |= RTL818X_TX_DESC_FLAG_MOREFRAG;
 250         if (info->control.rates[0].flags & IEEE80211_TX_RC_USE_RTS_CTS) {
 251                 flags |= RTL818X_TX_DESC_FLAG_RTS;
 252                 flags |= ieee80211_get_rts_cts_rate(dev, info)->hw_value << 19;
 253                 rts_dur = ieee80211_rts_duration(dev, priv->vif,
 254                                                  skb->len, info);
 255         } else if (info->control.rates[0].flags & IEEE80211_TX_RC_USE_CTS_PROTECT) {
 256                 flags |= RTL818X_TX_DESC_FLAG_CTS;
 257                 flags |= ieee80211_get_rts_cts_rate(dev, info)->hw_value << 19;
 258         }
 259
 260         if (!priv->is_rtl8187b) {
 261                 struct rtl8187_tx_hdr *hdr =
 262                         (struct rtl8187_tx_hdr *)skb_push(skb, sizeof(*hdr));
 263                 hdr->flags = cpu_to_le32(flags);
 264                 hdr->len = 0;
 265                 hdr->rts_duration = rts_dur;
 266                 hdr->retry = cpu_to_le32((info->control.rates[0].count - 1) << 8);
 267                 buf = hdr;
 268
 269                 ep = 2;
 270         } else {
 271                 /* fc needs to be calculated before skb_push() */
 272                 unsigned int epmap[4] = { 6, 7, 5, 4 };
 273                 struct ieee80211_hdr *tx_hdr =
 274                         (struct ieee80211_hdr *)(skb->data);
 275                 u16 fc = le16_to_cpu(tx_hdr->frame_control);
 276
 277                 struct rtl8187b_tx_hdr *hdr =
 278                         (struct rtl8187b_tx_hdr *)skb_push(skb, sizeof(*hdr));
 279                 struct ieee80211_rate *txrate =
 280                         ieee80211_get_tx_rate(dev, info);
 281                 memset(hdr, 0, sizeof(*hdr));
 282                 hdr->flags = cpu_to_le32(flags);
 283                 hdr->rts_duration = rts_dur;
 284                 hdr->retry = cpu_to_le32((info->control.rates[0].count - 1) << 8);
 285                 hdr->tx_duration =
 286                         ieee80211_generic_frame_duration(dev, priv->vif,
 287                                                          skb->len, txrate);
 288                 buf = hdr;
 289
 290                 if ((fc & IEEE80211_FCTL_FTYPE) == IEEE80211_FTYPE_MGMT)
 291                         ep = 12;
 292                 else
 293                         ep = epmap[skb_get_queue_mapping(skb)];
 294         }
 295
 296         info->rate_driver_data[0] = dev;
 297         info->rate_driver_data[1] = urb;
 298
 299         usb_fill_bulk_urb(urb, priv->udev, usb_sndbulkpipe(priv->udev, ep),
 300                           buf, skb->len, rtl8187_tx_cb, skb);
 301         urb->transfer_flags |= URB_ZERO_PACKET;
 302         usb_anchor_urb(urb, &priv->anchored);
 303         rc = usb_submit_urb(urb, GFP_ATOMIC);
 304         if (rc < 0) {
 305                 usb_unanchor_urb(urb);
 306                 kfree_skb(skb);
 307         }
 308         usb_free_urb(urb);
 309
 310         return NETDEV_TX_OK;
 311 }
 312
 313 static void rtl8187_rx_cb(struct urb *urb)
 314 {
 315         struct sk_buff *skb = (struct sk_buff *)urb->context;
 316         struct rtl8187_rx_info *info = (struct rtl8187_rx_info *)skb->cb;
 317         struct ieee80211_hw *dev = info->dev;
 318         struct rtl8187_priv *priv = dev->priv;
 319         struct ieee80211_rx_status rx_status = { 0 };
 320         int rate, signal;
 321         u32 flags;
 322         u32 quality;
 323         unsigned long f;
 324
 325         spin_lock_irqsave(&priv->rx_queue.lock, f);
 326         __skb_unlink(skb, &priv->rx_queue);
 327         spin_unlock_irqrestore(&priv->rx_queue.lock, f);
 328         skb_put(skb, urb->actual_length);
 329
 330         if (unlikely(urb->status)) {
 331                 dev_kfree_skb_irq(skb);
 332                 return;
 333         }
 334
 335         if (!priv->is_rtl8187b) {
 336                 struct rtl8187_rx_hdr *hdr =
 337                         (typeof(hdr))(skb_tail_pointer(skb) - sizeof(*hdr));
 338                 flags = le32_to_cpu(hdr->flags);
 339                 /* As with the RTL8187B below, the AGC is used to calculate
 340                  * signal strength and quality. In this case, the scaling
 341                  * constants are derived from the output of p54usb.
 342                  */
 343                 quality = 130 - ((41 * hdr->agc) >> 6);
 344                 signal = -4 - ((27 * hdr->agc) >> 6);
 345                 rx_status.antenna = (hdr->signal >> 7) & 1;
 346                 rx_status.mactime = le64_to_cpu(hdr->mac_time);
 347         } else {
 348                 struct rtl8187b_rx_hdr *hdr =
 349                         (typeof(hdr))(skb_tail_pointer(skb) - sizeof(*hdr));
 350                 /* The Realtek datasheet for the RTL8187B shows that the RX
 351                  * header contains the following quantities: signal quality,
 352                  * RSSI, AGC, the received power in dB, and the measured SNR.
 353                  * In testing, none of these quantities show qualitative
 354                  * agreement with AP signal strength, except for the AGC,
 355                  * which is inversely proportional to the strength of the
 356                  * signal. In the following, the quality and signal strength
 357                  * are derived from the AGC. The arbitrary scaling constants
 358                  * are chosen to make the results close to the values obtained
 359                  * for a BCM4312 using b43 as the driver. The noise is ignored
 360                  * for now.
 361                  */
 362                 flags = le32_to_cpu(hdr->flags);
 363                 quality = 170 - hdr->agc;
 364                 signal = 14 - hdr->agc / 2;
 365                 rx_status.antenna = (hdr->rssi >> 7) & 1;
 366                 rx_status.mactime = le64_to_cpu(hdr->mac_time);
 367         }
 368
 369         if (quality > 100)
 370                 quality = 100;
 371         rx_status.qual = quality;
 372         priv->quality = quality;
 373         rx_status.signal = signal;
 374         priv->signal = signal;
 375         rate = (flags >> 20) & 0xF;
 376         skb_trim(skb, flags & 0x0FFF);
 377         rx_status.rate_idx = rate;
 378         rx_status.freq = dev->conf.channel->center_freq;
 379         rx_status.band = dev->conf.channel->band;
 380         rx_status.flag |= RX_FLAG_TSFT;
 381         if (flags & RTL818X_RX_DESC_FLAG_CRC32_ERR)
 382                 rx_status.flag |= RX_FLAG_FAILED_FCS_CRC;
 383         ieee80211_rx_irqsafe(dev, skb, &rx_status);
 384
 385         skb = dev_alloc_skb(RTL8187_MAX_RX);
 386         if (unlikely(!skb)) {
 387                 /* TODO check rx queue length and refill *somewhere* */
 388                 return;
 389         }
 390
 391         info = (struct rtl8187_rx_info *)skb->cb;
 392         info->urb = urb;
 393         info->dev = dev;
 394         urb->transfer_buffer = skb_tail_pointer(skb);
 395         urb->context = skb;
 396         skb_queue_tail(&priv->rx_queue, skb);
 397
 398         usb_anchor_urb(urb, &priv->anchored);
 399         if (usb_submit_urb(urb, GFP_ATOMIC)) {
 400                 usb_unanchor_urb(urb);
 401                 skb_unlink(skb, &priv->rx_queue);
 402                 dev_kfree_skb_irq(skb);
 403         }
 404 }
 405
 406 static int rtl8187_init_urbs(struct ieee80211_hw *dev)
 407 {
 408         struct rtl8187_priv *priv = dev->priv;
 409         struct urb *entry = NULL;
 410         struct sk_buff *skb;
 411         struct rtl8187_rx_info *info;
 412         int ret = 0;
 413
 414         while (skb_queue_len(&priv->rx_queue) < 16) {
 415                 skb = __dev_alloc_skb(RTL8187_MAX_RX, GFP_KERNEL);
 416                 if (!skb) {
 417                         ret = -ENOMEM;
 418                         goto err;
 419                 }
 420                 entry = usb_alloc_urb(0, GFP_KERNEL);
 421                 if (!entry) {
 422                         ret = -ENOMEM;
 423                         goto err;
 424                 }
 425                 usb_fill_bulk_urb(entry, priv->udev,
 426                                   usb_rcvbulkpipe(priv->udev,
 427                                   priv->is_rtl8187b ? 3 : 1),
 428                                   skb_tail_pointer(skb),
 429                                   RTL8187_MAX_RX, rtl8187_rx_cb, skb);
 430                 info = (struct rtl8187_rx_info *)skb->cb;
 431                 info->urb = entry;
 432                 info->dev = dev;
 433                 skb_queue_tail(&priv->rx_queue, skb);
 434                 usb_anchor_urb(entry, &priv->anchored);
 435                 ret = usb_submit_urb(entry, GFP_KERNEL);
 436                 if (ret) {
 437                         skb_unlink(skb, &priv->rx_queue);
 438                         usb_unanchor_urb(entry);
 439                         goto err;
 440                 }
 441                 usb_free_urb(entry);
 442         }
 443         return ret;
 444
 445 err:
 446         usb_free_urb(entry);
 447         kfree_skb(skb);
 448         usb_kill_anchored_urbs(&priv->anchored);
 449         return ret;
 450 }
 451
 452 static void rtl8187b_status_cb(struct urb *urb)
 453 {
 454         struct ieee80211_hw *hw = (struct ieee80211_hw *)urb->context;
 455         struct rtl8187_priv *priv = hw->priv;
 456         u64 val;
 457         unsigned int cmd_type;
 458
 459         if (unlikely(urb->status))
 460                 return;
 461
 462         /*
 463          * Read from status buffer:
 464          *
 465          * bits [30:31] = cmd type:
 466          * - 0 indicates tx beacon interrupt
 467          * - 1 indicates tx close descriptor
 468          *
 469          * In the case of tx beacon interrupt:
 470          * [0:9] = Last Beacon CW
 471          * [10:29] = reserved
 472          * [30:31] = 00b
 473          * [32:63] = Last Beacon TSF
 474          *
 475          * If it's tx close descriptor:
 476          * [0:7] = Packet Retry Count
 477          * [8:14] = RTS Retry Count
 478          * [15] = TOK
 479          * [16:27] = Sequence No
 480          * [28] = LS
 481          * [29] = FS
 482          * [30:31] = 01b
 483          * [32:47] = unused (reserved?)
 484          * [48:63] = MAC Used Time
 485          */
 486         val = le64_to_cpu(priv->b_tx_status.buf);
 487
 488         cmd_type = (val >> 30) & 0x3;
 489         if (cmd_type == 1) {
 490                 unsigned int pkt_rc, seq_no;
 491                 bool tok;
 492                 struct sk_buff *skb;
 493                 struct ieee80211_hdr *ieee80211hdr;
 494                 unsigned long flags;
 495
 496                 pkt_rc = val & 0xFF;
 497                 tok = val & (1 << 15);
 498                 seq_no = (val >> 16) & 0xFFF;
 499
 500                 spin_lock_irqsave(&priv->b_tx_status.queue.lock, flags);
 501                 skb_queue_reverse_walk(&priv->b_tx_status.queue, skb) {
 502                         ieee80211hdr = (struct ieee80211_hdr *)skb->data;
 503
 504                         /*
 505                          * While testing, it was discovered that the seq_no
 506                          * doesn't actually contains the sequence number.
 507                          * Instead of returning just the 12 bits of sequence
 508                          * number, hardware is returning entire sequence control
 509                          * (fragment number plus sequence number) in a 12 bit
 510                          * only field overflowing after some time. As a
 511                          * workaround, just consider the lower bits, and expect
 512                          * it's unlikely we wrongly ack some sent data
 513                          */
 514                         if ((le16_to_cpu(ieee80211hdr->seq_ctrl)
 515                             & 0xFFF) == seq_no)
 516                                 break;
 517                 }
 518                 if (skb != (struct sk_buff *) &priv->b_tx_status.queue) {
 519                         struct ieee80211_tx_info *info = IEEE80211_SKB_CB(skb);
 520
 521                         __skb_unlink(skb, &priv->b_tx_status.queue);
 522                         if (tok)
 523                                 info->flags |= IEEE80211_TX_STAT_ACK;
 524                         info->status.rates[0].count = pkt_rc + 1;
 525
 526                         ieee80211_tx_status_irqsafe(hw, skb);
 527                 }
 528                 spin_unlock_irqrestore(&priv->b_tx_status.queue.lock, flags);
 529         }
 530
 531         usb_anchor_urb(urb, &priv->anchored);
 532         if (usb_submit_urb(urb, GFP_ATOMIC))
 533                 usb_unanchor_urb(urb);
 534 }
 535
 536 static int rtl8187b_init_status_urb(struct ieee80211_hw *dev)
 537 {
 538         struct rtl8187_priv *priv = dev->priv;
 539         struct urb *entry;
 540         int ret = 0;
 541
 542         entry = usb_alloc_urb(0, GFP_KERNEL);
 543         if (!entry)
 544                 return -ENOMEM;
 545
 546         usb_fill_bulk_urb(entry, priv->udev, usb_rcvbulkpipe(priv->udev, 9),
 547                           &priv->b_tx_status.buf, sizeof(priv->b_tx_status.buf),
 548                           rtl8187b_status_cb, dev);
 549
 550         usb_anchor_urb(entry, &priv->anchored);
 551         ret = usb_submit_urb(entry, GFP_KERNEL);
 552         if (ret)
 553                 usb_unanchor_urb(entry);
 554         usb_free_urb(entry);
 555
 556         return ret;
 557 }
 558
 559 static int rtl8187_cmd_reset(struct ieee80211_hw *dev)
 560 {
 561         struct rtl8187_priv *priv = dev->priv;
 562         u8 reg;
 563         int i;
 564
 565         reg = rtl818x_ioread8(priv, &priv->map->CMD);
 566         reg &= (1 << 1);
 567         reg |= RTL818X_CMD_RESET;
 568         rtl818x_iowrite8(priv, &priv->map->CMD, reg);
 569
 570         i = 10;
 571         do {
 572                 msleep(2);
 573                 if (!(rtl818x_ioread8(priv, &priv->map->CMD) &
 574                       RTL818X_CMD_RESET))
 575                         break;
 576         } while (--i);
 577
 578         if (!i) {
 579                 printk(KERN_ERR "%s: Reset timeout!\n", wiphy_name(dev->wiphy));
 580                 return -ETIMEDOUT;
 581         }
 582
 583         /* reload registers from eeprom */
 584         rtl818x_iowrite8(priv, &priv->map->EEPROM_CMD, RTL818X_EEPROM_CMD_LOAD);
 585
 586         i = 10;
 587         do {
 588                 msleep(4);
 589                 if (!(rtl818x_ioread8(priv, &priv->map->EEPROM_CMD) &
 590                       RTL818X_EEPROM_CMD_CONFIG))
 591                         break;
 592         } while (--i);
 593
 594         if (!i) {
 595                 printk(KERN_ERR "%s: eeprom reset timeout!\n",
 596                        wiphy_name(dev->wiphy));
 597                 return -ETIMEDOUT;
 598         }
 599
 600         return 0;
 601 }
 602
 603 static int rtl8187_init_hw(struct ieee80211_hw *dev)
 604 {
 605         struct rtl8187_priv *priv = dev->priv;
 606         u8 reg;
 607         int res;
 608
 609         /* reset */
 610         rtl818x_iowrite8(priv, &priv->map->EEPROM_CMD,
 611                          RTL818X_EEPROM_CMD_CONFIG);
 612         reg = rtl818x_ioread8(priv, &priv->map->CONFIG3);
 613         rtl818x_iowrite8(priv, &priv->map->CONFIG3, reg |
 614                          RTL818X_CONFIG3_ANAPARAM_WRITE);
 615         rtl818x_iowrite32(priv, &priv->map->ANAPARAM,
 616                           RTL8187_RTL8225_ANAPARAM_ON);
 617         rtl818x_iowrite32(priv, &priv->map->ANAPARAM2,
 618                           RTL8187_RTL8225_ANAPARAM2_ON);
 619         rtl818x_iowrite8(priv, &priv->map->CONFIG3, reg &
 620                          ~RTL818X_CONFIG3_ANAPARAM_WRITE);
 621         rtl818x_iowrite8(priv, &priv->map->EEPROM_CMD,
 622                          RTL818X_EEPROM_CMD_NORMAL);
 623
 624         rtl818x_iowrite16(priv, &priv->map->INT_MASK, 0);
 625
 626         msleep(200);
 627         rtl818x_iowrite8(priv, (u8 *)0xFE18, 0x10);
 628         rtl818x_iowrite8(priv, (u8 *)0xFE18, 0x11);
 629         rtl818x_iowrite8(priv, (u8 *)0xFE18, 0x00);
 630         msleep(200);
 631
 632         res = rtl8187_cmd_reset(dev);
 633         if (res)
 634                 return res;
 635
 636         rtl818x_iowrite8(priv, &priv->map->EEPROM_CMD, RTL818X_EEPROM_CMD_CONFIG);
 637         reg = rtl818x_ioread8(priv, &priv->map->CONFIG3);
 638         rtl818x_iowrite8(priv, &priv->map->CONFIG3,
 639                         reg | RTL818X_CONFIG3_ANAPARAM_WRITE);
 640         rtl818x_iowrite32(priv, &priv->map->ANAPARAM,
 641                           RTL8187_RTL8225_ANAPARAM_ON);
 642         rtl818x_iowrite32(priv, &priv->map->ANAPARAM2,
 643                           RTL8187_RTL8225_ANAPARAM2_ON);
 644         rtl818x_iowrite8(priv, &priv->map->CONFIG3,
 645                         reg & ~RTL818X_CONFIG3_ANAPARAM_WRITE);
 646         rtl818x_iowrite8(priv, &priv->map->EEPROM_CMD, RTL818X_EEPROM_CMD_NORMAL);
 647
 648         /* setup card */
 649         rtl818x_iowrite16(priv, &priv->map->RFPinsSelect, 0);
 650         rtl818x_iowrite8(priv, &priv->map->GPIO, 0);
 651
 652         rtl818x_iowrite16(priv, &priv->map->RFPinsSelect, (4 << 8));
 653         rtl818x_iowrite8(priv, &priv->map->GPIO, 1);
 654         rtl818x_iowrite8(priv, &priv->map->GP_ENABLE, 0);
 655
 656         rtl818x_iowrite8(priv, &priv->map->EEPROM_CMD, RTL818X_EEPROM_CMD_CONFIG);
 657
 658         rtl818x_iowrite16(priv, (__le16 *)0xFFF4, 0xFFFF);
 659         reg = rtl818x_ioread8(priv, &priv->map->CONFIG1);
 660         reg &= 0x3F;
 661         reg |= 0x80;
 662         rtl818x_iowrite8(priv, &priv->map->CONFIG1, reg);
 663
 664         rtl818x_iowrite8(priv, &priv->map->EEPROM_CMD, RTL818X_EEPROM_CMD_NORMAL);
 665
 666         rtl818x_iowrite32(priv, &priv->map->INT_TIMEOUT, 0);
 667         rtl818x_iowrite8(priv, &priv->map->WPA_CONF, 0);
 668         rtl818x_iowrite8(priv, &priv->map->RATE_FALLBACK, 0);
 669
 670         // TODO: set RESP_RATE and BRSR properly
 671         rtl818x_iowrite8(priv, &priv->map->RESP_RATE, (8 << 4) | 0);
 672         rtl818x_iowrite16(priv, &priv->map->BRSR, 0x01F3);
 673
 674         /* host_usb_init */
 675         rtl818x_iowrite16(priv, &priv->map->RFPinsSelect, 0);
 676         rtl818x_iowrite8(priv, &priv->map->GPIO, 0);
 677         reg = rtl818x_ioread8(priv, (u8 *)0xFE53);
 678         rtl818x_iowrite8(priv, (u8 *)0xFE53, reg | (1 << 7));
 679         rtl818x_iowrite16(priv, &priv->map->RFPinsSelect, (4 << 8));
 680         rtl818x_iowrite8(priv, &priv->map->GPIO, 0x20);
 681         rtl818x_iowrite8(priv, &priv->map->GP_ENABLE, 0);
 682         rtl818x_iowrite16(priv, &priv->map->RFPinsOutput, 0x80);
 683         rtl818x_iowrite16(priv, &priv->map->RFPinsSelect, 0x80);
 684         rtl818x_iowrite16(priv, &priv->map->RFPinsEnable, 0x80);
 685         msleep(100);
 686
 687         rtl818x_iowrite32(priv, &priv->map->RF_TIMING, 0x000a8008);
 688         rtl818x_iowrite16(priv, &priv->map->BRSR, 0xFFFF);
 689         rtl818x_iowrite32(priv, &priv->map->RF_PARA, 0x00100044);
 690         rtl818x_iowrite8(priv, &priv->map->EEPROM_CMD,
 691                          RTL818X_EEPROM_CMD_CONFIG);
 692         rtl818x_iowrite8(priv, &priv->map->CONFIG3, 0x44);
 693         rtl818x_iowrite8(priv, &priv->map->EEPROM_CMD,
 694                          RTL818X_EEPROM_CMD_NORMAL);
 695         rtl818x_iowrite16(priv, &priv->map->RFPinsEnable, 0x1FF7);
 696         msleep(100);
 697
 698         priv->rf->init(dev);
 699
 700         rtl818x_iowrite16(priv, &priv->map->BRSR, 0x01F3);
 701         reg = rtl818x_ioread8(priv, &priv->map->PGSELECT) & ~1;
 702         rtl818x_iowrite8(priv, &priv->map->PGSELECT, reg | 1);
 703         rtl818x_iowrite16(priv, (__le16 *)0xFFFE, 0x10);
 704         rtl818x_iowrite8(priv, &priv->map->TALLY_SEL, 0x80);
 705         rtl818x_iowrite8(priv, (u8 *)0xFFFF, 0x60);
 706         rtl818x_iowrite8(priv, &priv->map->PGSELECT, reg);
 707
 708         return 0;
 709 }
 710
 711 static const u8 rtl8187b_reg_table[][3] = {
 712         {0xF0, 0x32, 0}, {0xF1, 0x32, 0}, {0xF2, 0x00, 0}, {0xF3, 0x00, 0},
 713         {0xF4, 0x32, 0}, {0xF5, 0x43, 0}, {0xF6, 0x00, 0}, {0xF7, 0x00, 0},
 714         {0xF8, 0x46, 0}, {0xF9, 0xA4, 0}, {0xFA, 0x00, 0}, {0xFB, 0x00, 0},
 715         {0xFC, 0x96, 0}, {0xFD, 0xA4, 0}, {0xFE, 0x00, 0}, {0xFF, 0x00, 0},
 716
 717         {0x58, 0x4B, 1}, {0x59, 0x00, 1}, {0x5A, 0x4B, 1}, {0x5B, 0x00, 1},
 718         {0x60, 0x4B, 1}, {0x61, 0x09, 1}, {0x62, 0x4B, 1}, {0x63, 0x09, 1},
 719         {0xCE, 0x0F, 1}, {0xCF, 0x00, 1}, {0xE0, 0xFF, 1}, {0xE1, 0x0F, 1},
 720         {0xE2, 0x00, 1}, {0xF0, 0x4E, 1}, {0xF1, 0x01, 1}, {0xF2, 0x02, 1},
 721         {0xF3, 0x03, 1}, {0xF4, 0x04, 1}, {0xF5, 0x05, 1}, {0xF6, 0x06, 1},
 722         {0xF7, 0x07, 1}, {0xF8, 0x08, 1},
 723
 724         {0x4E, 0x00, 2}, {0x0C, 0x04, 2}, {0x21, 0x61, 2}, {0x22, 0x68, 2},
 725         {0x23, 0x6F, 2}, {0x24, 0x76, 2}, {0x25, 0x7D, 2}, {0x26, 0x84, 2},
 726         {0x27, 0x8D, 2}, {0x4D, 0x08, 2}, {0x50, 0x05, 2}, {0x51, 0xF5, 2},
 727         {0x52, 0x04, 2}, {0x53, 0xA0, 2}, {0x54, 0x1F, 2}, {0x55, 0x23, 2},
 728         {0x56, 0x45, 2}, {0x57, 0x67, 2}, {0x58, 0x08, 2}, {0x59, 0x08, 2},
 729         {0x5A, 0x08, 2}, {0x5B, 0x08, 2}, {0x60, 0x08, 2}, {0x61, 0x08, 2},
 730         {0x62, 0x08, 2}, {0x63, 0x08, 2}, {0x64, 0xCF, 2}, {0x72, 0x56, 2},
 731         {0x73, 0x9A, 2},
 732
 733         {0x34, 0xF0, 0}, {0x35, 0x0F, 0}, {0x5B, 0x40, 0}, {0x84, 0x88, 0},
 734         {0x85, 0x24, 0}, {0x88, 0x54, 0}, {0x8B, 0xB8, 0}, {0x8C, 0x07, 0},
 735         {0x8D, 0x00, 0}, {0x94, 0x1B, 0}, {0x95, 0x12, 0}, {0x96, 0x00, 0},
 736         {0x97, 0x06, 0}, {0x9D, 0x1A, 0}, {0x9F, 0x10, 0}, {0xB4, 0x22, 0},
 737         {0xBE, 0x80, 0}, {0xDB, 0x00, 0}, {0xEE, 0x00, 0}, {0x4C, 0x00, 2},
 738
 739         {0x9F, 0x00, 3}, {0x8C, 0x01, 0}, {0x8D, 0x10, 0}, {0x8E, 0x08, 0},
 740         {0x8F, 0x00, 0}
 741 };
 742
 743 static int rtl8187b_init_hw(struct ieee80211_hw *dev)
 744 {
 745         struct rtl8187_priv *priv = dev->priv;
 746         int res, i;
 747         u8 reg;
 748
 749         rtl818x_iowrite8(priv, &priv->map->EEPROM_CMD,
 750                          RTL818X_EEPROM_CMD_CONFIG);
 751
 752         reg = rtl818x_ioread8(priv, &priv->map->CONFIG3);
 753         reg |= RTL818X_CONFIG3_ANAPARAM_WRITE | RTL818X_CONFIG3_GNT_SELECT;
 754         rtl818x_iowrite8(priv, &priv->map->CONFIG3, reg);
 755         rtl818x_iowrite32(priv, &priv->map->ANAPARAM2,
 756                           RTL8187B_RTL8225_ANAPARAM2_ON);
 757         rtl818x_iowrite32(priv, &priv->map->ANAPARAM,
 758                           RTL8187B_RTL8225_ANAPARAM_ON);
 759         rtl818x_iowrite8(priv, &priv->map->ANAPARAM3,
 760                          RTL8187B_RTL8225_ANAPARAM3_ON);
 761
 762         rtl818x_iowrite8(priv, (u8 *)0xFF61, 0x10);
 763         reg = rtl818x_ioread8(priv, (u8 *)0xFF62);
 764         rtl818x_iowrite8(priv, (u8 *)0xFF62, reg & ~(1 << 5));
 765         rtl818x_iowrite8(priv, (u8 *)0xFF62, reg | (1 << 5));
 766
 767         reg = rtl818x_ioread8(priv, &priv->map->CONFIG3);
 768         reg &= ~RTL818X_CONFIG3_ANAPARAM_WRITE;
 769         rtl818x_iowrite8(priv, &priv->map->CONFIG3, reg);
 770
 771         rtl818x_iowrite8(priv, &priv->map->EEPROM_CMD,
 772                          RTL818X_EEPROM_CMD_NORMAL);
 773
 774         res = rtl8187_cmd_reset(dev);
 775         if (res)
 776                 return res;
 777
 778         rtl818x_iowrite16(priv, (__le16 *)0xFF2D, 0x0FFF);
 779         reg = rtl818x_ioread8(priv, &priv->map->CW_CONF);
 780         reg |= RTL818X_CW_CONF_PERPACKET_RETRY_SHIFT;
 781         rtl818x_iowrite8(priv, &priv->map->CW_CONF, reg);
 782         reg = rtl818x_ioread8(priv, &priv->map->TX_AGC_CTL);
 783         reg |= RTL818X_TX_AGC_CTL_PERPACKET_GAIN_SHIFT |
 784                RTL818X_TX_AGC_CTL_PERPACKET_ANTSEL_SHIFT;
 785         rtl818x_iowrite8(priv, &priv->map->TX_AGC_CTL, reg);
 786
 787         rtl818x_iowrite16_idx(priv, (__le16 *)0xFFE0, 0x0FFF, 1);
 788
 789         rtl818x_iowrite16(priv, &priv->map->BEACON_INTERVAL, 100);
 790         rtl818x_iowrite16(priv, &priv->map->ATIM_WND, 2);
 791         rtl818x_iowrite16_idx(priv, (__le16 *)0xFFD4, 0xFFFF, 1);
 792
 793         rtl818x_iowrite8(priv, &priv->map->EEPROM_CMD,
 794                          RTL818X_EEPROM_CMD_CONFIG);
 795         reg = rtl818x_ioread8(priv, &priv->map->CONFIG1);
 796         rtl818x_iowrite8(priv, &priv->map->CONFIG1, (reg & 0x3F) | 0x80);
 797         rtl818x_iowrite8(priv, &priv->map->EEPROM_CMD,
 798                          RTL818X_EEPROM_CMD_NORMAL);
 799
 800         rtl818x_iowrite8(priv, &priv->map->WPA_CONF, 0);
 801         for (i = 0; i < ARRAY_SIZE(rtl8187b_reg_table); i++) {
 802                 rtl818x_iowrite8_idx(priv,
 803                                      (u8 *)(uintptr_t)
 804                                      (rtl8187b_reg_table[i][0] | 0xFF00),
 805                                      rtl8187b_reg_table[i][1],
 806                                      rtl8187b_reg_table[i][2]);
 807         }
 808
 809         rtl818x_iowrite16(priv, &priv->map->TID_AC_MAP, 0xFA50);
 810         rtl818x_iowrite16(priv, &priv->map->INT_MIG, 0);
 811
 812         rtl818x_iowrite32_idx(priv, (__le32 *)0xFFF0, 0, 1);
 813         rtl818x_iowrite32_idx(priv, (__le32 *)0xFFF4, 0, 1);
 814         rtl818x_iowrite8_idx(priv, (u8 *)0xFFF8, 0, 1);
 815
 816         rtl818x_iowrite32(priv, &priv->map->RF_TIMING, 0x00004001);
 817
 818         rtl818x_iowrite16_idx(priv, (__le16 *)0xFF72, 0x569A, 2);
 819
 820         rtl818x_iowrite8(priv, &priv->map->EEPROM_CMD,
 821                          RTL818X_EEPROM_CMD_CONFIG);
 822         reg = rtl818x_ioread8(priv, &priv->map->CONFIG3);
 823         reg |= RTL818X_CONFIG3_ANAPARAM_WRITE;
 824         rtl818x_iowrite8(priv, &priv->map->CONFIG3, reg);
 825         rtl818x_iowrite8(priv, &priv->map->EEPROM_CMD,
 826                          RTL818X_EEPROM_CMD_NORMAL);
 827
 828         rtl818x_iowrite16(priv, &priv->map->RFPinsOutput, 0x0480);
 829         rtl818x_iowrite16(priv, &priv->map->RFPinsSelect, 0x2488);
 830         rtl818x_iowrite16(priv, &priv->map->RFPinsEnable, 0x1FFF);
 831         msleep(100);
 832
 833         priv->rf->init(dev);
 834
 835         reg = RTL818X_CMD_TX_ENABLE | RTL818X_CMD_RX_ENABLE;
 836         rtl818x_iowrite8(priv, &priv->map->CMD, reg);
 837         rtl818x_iowrite16(priv, &priv->map->INT_MASK, 0xFFFF);
 838
 839         rtl818x_iowrite8(priv, (u8 *)0xFE41, 0xF4);
 840         rtl818x_iowrite8(priv, (u8 *)0xFE40, 0x00);
 841         rtl818x_iowrite8(priv, (u8 *)0xFE42, 0x00);
 842         rtl818x_iowrite8(priv, (u8 *)0xFE42, 0x01);
 843         rtl818x_iowrite8(priv, (u8 *)0xFE40, 0x0F);
 844         rtl818x_iowrite8(priv, (u8 *)0xFE42, 0x00);
 845         rtl818x_iowrite8(priv, (u8 *)0xFE42, 0x01);
 846
 847         reg = rtl818x_ioread8(priv, (u8 *)0xFFDB);
 848         rtl818x_iowrite8(priv, (u8 *)0xFFDB, reg | (1 << 2));
 849         rtl818x_iowrite16_idx(priv, (__le16 *)0xFF72, 0x59FA, 3);
 850         rtl818x_iowrite16_idx(priv, (__le16 *)0xFF74, 0x59D2, 3);
 851         rtl818x_iowrite16_idx(priv, (__le16 *)0xFF76, 0x59D2, 3);
 852         rtl818x_iowrite16_idx(priv, (__le16 *)0xFF78, 0x19FA, 3);
 853         rtl818x_iowrite16_idx(priv, (__le16 *)0xFF7A, 0x19FA, 3);
 854         rtl818x_iowrite16_idx(priv, (__le16 *)0xFF7C, 0x00D0, 3);
 855         rtl818x_iowrite8(priv, (u8 *)0xFF61, 0);
 856         rtl818x_iowrite8_idx(priv, (u8 *)0xFF80, 0x0F, 1);
 857         rtl818x_iowrite8_idx(priv, (u8 *)0xFF83, 0x03, 1);
 858         rtl818x_iowrite8(priv, (u8 *)0xFFDA, 0x10);
 859         rtl818x_iowrite8_idx(priv, (u8 *)0xFF4D, 0x08, 2);
 860
 861         rtl818x_iowrite32(priv, &priv->map->HSSI_PARA, 0x0600321B);
 862
 863         rtl818x_iowrite16_idx(priv, (__le16 *)0xFFEC, 0x0800, 1);
 864
 865         priv->slot_time = 0x9;
 866         priv->aifsn[0] = 2; /* AIFSN[AC_VO] */
 867         priv->aifsn[1] = 2; /* AIFSN[AC_VI] */
 868         priv->aifsn[2] = 7; /* AIFSN[AC_BK] */
 869         priv->aifsn[3] = 3; /* AIFSN[AC_BE] */
 870         rtl818x_iowrite8(priv, &priv->map->ACM_CONTROL, 0);
 871
 872         /* ENEDCA flag must always be set, transmit issues? */
 873         rtl818x_iowrite8(priv, &priv->map->MSR, RTL818X_MSR_ENEDCA);
 874
 875         return 0;
 876 }
 877
 878 static void rtl8187_work(struct work_struct *work)
 879 {
 880         /* The RTL8187 returns the retry count through register 0xFFFA. In
 881          * addition, it appears to be a cumulative retry count, not the
 882          * value for the current TX packet. When multiple TX entries are
 883          * queued, the retry count will be valid for the last one in the queue.
 884          * The "error" should not matter for purposes of rate setting. */
 885         struct rtl8187_priv *priv = container_of(work, struct rtl8187_priv,
 886                                     work.work);
 887         struct ieee80211_tx_info *info;
 888         struct ieee80211_hw *dev = priv->dev;
 889         static u16 retry;
 890         u16 tmp;
 891
 892         mutex_lock(&priv->conf_mutex);
 893         tmp = rtl818x_ioread16(priv, (__le16 *)0xFFFA);
 894         while (skb_queue_len(&priv->b_tx_status.queue) > 0) {
 895                 struct sk_buff *old_skb;
 896
 897                 old_skb = skb_dequeue(&priv->b_tx_status.queue);
 898                 info = IEEE80211_SKB_CB(old_skb);
 899                 info->status.rates[0].count = tmp - retry + 1;
 900                 ieee80211_tx_status_irqsafe(dev, old_skb);
 901         }
 902         retry = tmp;
 903         mutex_unlock(&priv->conf_mutex);
 904 }
 905
 906 static int rtl8187_start(struct ieee80211_hw *dev)
 907 {
 908         struct rtl8187_priv *priv = dev->priv;
 909         u32 reg;
 910         int ret;
 911
 912         ret = (!priv->is_rtl8187b) ? rtl8187_init_hw(dev) :
 913                                      rtl8187b_init_hw(dev);
 914         if (ret)
 915                 return ret;
 916
 917         mutex_lock(&priv->conf_mutex);
 918
 919         init_usb_anchor(&priv->anchored);
 920         priv->dev = dev;
 921
 922         if (priv->is_rtl8187b) {
 923                 reg = RTL818X_RX_CONF_MGMT |
 924                       RTL818X_RX_CONF_DATA |
 925                       RTL818X_RX_CONF_BROADCAST |
 926                       RTL818X_RX_CONF_NICMAC |
 927                       RTL818X_RX_CONF_BSSID |
 928                       (7 << 13 /* RX FIFO threshold NONE */) |
 929                       (7 << 10 /* MAX RX DMA */) |
 930                       RTL818X_RX_CONF_RX_AUTORESETPHY |
 931                       RTL818X_RX_CONF_ONLYERLPKT |
 932                       RTL818X_RX_CONF_MULTICAST;
 933                 priv->rx_conf = reg;
 934                 rtl818x_iowrite32(priv, &priv->map->RX_CONF, reg);
 935
 936                 rtl818x_iowrite32(priv, &priv->map->TX_CONF,
 937                                   RTL818X_TX_CONF_HW_SEQNUM |
 938                                   RTL818X_TX_CONF_DISREQQSIZE |
 939                                   (7 << 8  /* short retry limit */) |
 940                                   (7 << 0  /* long retry limit */) |
 941                                   (7 << 21 /* MAX TX DMA */));
 942                 rtl8187_init_urbs(dev);
 943                 rtl8187b_init_status_urb(dev);
 944                 mutex_unlock(&priv->conf_mutex);
 945                 return 0;
 946         }
 947
 948         rtl818x_iowrite16(priv, &priv->map->INT_MASK, 0xFFFF);
 949
 950         rtl818x_iowrite32(priv, &priv->map->MAR[0], ~0);
 951         rtl818x_iowrite32(priv, &priv->map->MAR[1], ~0);
 952
 953         rtl8187_init_urbs(dev);
 954
 955         reg = RTL818X_RX_CONF_ONLYERLPKT |
 956               RTL818X_RX_CONF_RX_AUTORESETPHY |
 957               RTL818X_RX_CONF_BSSID |
 958               RTL818X_RX_CONF_MGMT |
 959               RTL818X_RX_CONF_DATA |
 960               (7 << 13 /* RX FIFO threshold NONE */) |
 961               (7 << 10 /* MAX RX DMA */) |
 962               RTL818X_RX_CONF_BROADCAST |
 963               RTL818X_RX_CONF_NICMAC;
 964
 965         priv->rx_conf = reg;
 966         rtl818x_iowrite32(priv, &priv->map->RX_CONF, reg);
 967
 968         reg = rtl818x_ioread8(priv, &priv->map->CW_CONF);
 969         reg &= ~RTL818X_CW_CONF_PERPACKET_CW_SHIFT;
 970         reg |= RTL818X_CW_CONF_PERPACKET_RETRY_SHIFT;
 971         rtl818x_iowrite8(priv, &priv->map->CW_CONF, reg);
 972
 973         reg = rtl818x_ioread8(priv, &priv->map->TX_AGC_CTL);
 974         reg &= ~RTL818X_TX_AGC_CTL_PERPACKET_GAIN_SHIFT;
 975         reg &= ~RTL818X_TX_AGC_CTL_PERPACKET_ANTSEL_SHIFT;
 976         reg &= ~RTL818X_TX_AGC_CTL_FEEDBACK_ANT;
 977         rtl818x_iowrite8(priv, &priv->map->TX_AGC_CTL, reg);
 978
 979         reg  = RTL818X_TX_CONF_CW_MIN |
 980                (7 << 21 /* MAX TX DMA */) |
 981                RTL818X_TX_CONF_NO_ICV;
 982         rtl818x_iowrite32(priv, &priv->map->TX_CONF, reg);
 983
 984         reg = rtl818x_ioread8(priv, &priv->map->CMD);
 985         reg |= RTL818X_CMD_TX_ENABLE;
 986         reg |= RTL818X_CMD_RX_ENABLE;
 987         rtl818x_iowrite8(priv, &priv->map->CMD, reg);
 988         INIT_DELAYED_WORK(&priv->work, rtl8187_work);
 989         mutex_unlock(&priv->conf_mutex);
 990
 991         return 0;
 992 }
 993
 994 static void rtl8187_stop(struct ieee80211_hw *dev)
 995 {
 996         struct rtl8187_priv *priv = dev->priv;
 997         struct sk_buff *skb;
 998         u32 reg;
 999
1000         mutex_lock(&priv->conf_mutex);
1001         rtl818x_iowrite16(priv, &priv->map->INT_MASK, 0);
1002
1003         reg = rtl818x_ioread8(priv, &priv->map->CMD);
1004         reg &= ~RTL818X_CMD_TX_ENABLE;
1005         reg &= ~RTL818X_CMD_RX_ENABLE;
1006         rtl818x_iowrite8(priv, &priv->map->CMD, reg);
1007
1008         priv->rf->stop(dev);
1009
1010         rtl818x_iowrite8(priv, &priv->map->EEPROM_CMD, RTL818X_EEPROM_CMD_CONFIG);
1011         reg = rtl818x_ioread8(priv, &priv->map->CONFIG4);
1012         rtl818x_iowrite8(priv, &priv->map->CONFIG4, reg | RTL818X_CONFIG4_VCOOFF);
1013         rtl818x_iowrite8(priv, &priv->map->EEPROM_CMD, RTL818X_EEPROM_CMD_NORMAL);
1014
1015         while ((skb = skb_dequeue(&priv->b_tx_status.queue)))
1016                 dev_kfree_skb_any(skb);
1017
1018         usb_kill_anchored_urbs(&priv->anchored);
1019         if (!priv->is_rtl8187b)
1020                 cancel_delayed_work_sync(&priv->work);
1021         mutex_unlock(&priv->conf_mutex);
1022 }
1023
1024 static int rtl8187_add_interface(struct ieee80211_hw *dev,
1025                                  struct ieee80211_if_init_conf *conf)
1026 {
1027         struct rtl8187_priv *priv = dev->priv;
1028         int i;
1029         int ret = -EOPNOTSUPP;
1030
1031         mutex_lock(&priv->conf_mutex);
1032         if (priv->mode != NL80211_IFTYPE_MONITOR)
1033                 goto exit;
1034
1035         switch (conf->type) {
1036         case NL80211_IFTYPE_STATION:
1037                 priv->mode = conf->type;
1038                 break;
1039         default:
1040                 goto exit;
1041         }
1042
1043         ret = 0;
1044         priv->vif = conf->vif;
1045
1046         rtl818x_iowrite8(priv, &priv->map->EEPROM_CMD, RTL818X_EEPROM_CMD_CONFIG);
1047         for (i = 0; i < ETH_ALEN; i++)
1048                 rtl818x_iowrite8(priv, &priv->map->MAC[i],
1049                                  ((u8 *)conf->mac_addr)[i]);
1050         rtl818x_iowrite8(priv, &priv->map->EEPROM_CMD, RTL818X_EEPROM_CMD_NORMAL);
1051
1052 exit:
1053         mutex_unlock(&priv->conf_mutex);
1054         return ret;
1055 }
1056
1057 static void rtl8187_remove_interface(struct ieee80211_hw *dev,
1058                                      struct ieee80211_if_init_conf *conf)
1059 {
1060         struct rtl8187_priv *priv = dev->priv;
1061         mutex_lock(&priv->conf_mutex);
1062         priv->mode = NL80211_IFTYPE_MONITOR;
1063         priv->vif = NULL;
1064         mutex_unlock(&priv->conf_mutex);
1065 }
1066
1067 static int rtl8187_config(struct ieee80211_hw *dev, u32 changed)
1068 {
1069         struct rtl8187_priv *priv = dev->priv;
1070         struct ieee80211_conf *conf = &dev->conf;
1071         u32 reg;
1072
1073         mutex_lock(&priv->conf_mutex);
1074         reg = rtl818x_ioread32(priv, &priv->map->TX_CONF);
1075         /* Enable TX loopback on MAC level to avoid TX during channel
1076          * changes, as this has be seen to causes problems and the
1077          * card will stop work until next reset
1078          */
1079         rtl818x_iowrite32(priv, &priv->map->TX_CONF,
1080                           reg | RTL818X_TX_CONF_LOOPBACK_MAC);
1081         priv->rf->set_chan(dev, conf);
1082         msleep(10);
1083         rtl818x_iowrite32(priv, &priv->map->TX_CONF, reg);
1084
1085         rtl818x_iowrite16(priv, &priv->map->ATIM_WND, 2);
1086         rtl818x_iowrite16(priv, &priv->map->ATIMTR_INTERVAL, 100);
1087         rtl818x_iowrite16(priv, &priv->map->BEACON_INTERVAL, 100);
1088         rtl818x_iowrite16(priv, &priv->map->BEACON_INTERVAL_TIME, 100);
1089         mutex_unlock(&priv->conf_mutex);
1090         return 0;
1091 }
1092
1093 /*
1094  * With 8187B, AC_*_PARAM clashes with FEMR definition in struct rtl818x_csr for
1095  * example. Thus we have to use raw values for AC_*_PARAM register addresses.
1096  */
1097 static __le32 *rtl8187b_ac_addr[4] = {
1098         (__le32 *) 0xFFF0, /* AC_VO */
1099         (__le32 *) 0xFFF4, /* AC_VI */
1100         (__le32 *) 0xFFFC, /* AC_BK */
1101         (__le32 *) 0xFFF8, /* AC_BE */
1102 };
1103
1104 #define SIFS_TIME 0xa
1105
1106 static void rtl8187_conf_erp(struct rtl8187_priv *priv, bool use_short_slot,
1107                              bool use_short_preamble)
1108 {
1109         if (priv->is_rtl8187b) {
1110                 u8 difs, eifs;
1111                 u16 ack_timeout;
1112                 int queue;
1113
1114                 if (use_short_slot) {
1115                         priv->slot_time = 0x9;
1116                         difs = 0x1c;
1117                         eifs = 0x53;
1118                 } else {
1119                         priv->slot_time = 0x14;
1120                         difs = 0x32;
1121                         eifs = 0x5b;
1122                 }
1123                 rtl818x_iowrite8(priv, &priv->map->SIFS, 0x22);
1124                 rtl818x_iowrite8(priv, &priv->map->SLOT, priv->slot_time);
1125                 rtl818x_iowrite8(priv, &priv->map->DIFS, difs);
1126
1127                 /*
1128                  * BRSR+1 on 8187B is in fact EIFS register
1129                  * Value in units of 4 us
1130                  */
1131                 rtl818x_iowrite8(priv, (u8 *)&priv->map->BRSR + 1, eifs);
1132
1133                 /*
1134                  * For 8187B, CARRIER_SENSE_COUNTER is in fact ack timeout
1135                  * register. In units of 4 us like eifs register
1136                  * ack_timeout = ack duration + plcp + difs + preamble
1137                  */
1138                 ack_timeout = 112 + 48 + difs;
1139                 if (use_short_preamble)
1140                         ack_timeout += 72;
1141                 else
1142                         ack_timeout += 144;
1143                 rtl818x_iowrite8(priv, &priv->map->CARRIER_SENSE_COUNTER,
1144                                  DIV_ROUND_UP(ack_timeout, 4));
1145
1146                 for (queue = 0; queue < 4; queue++)
1147                         rtl818x_iowrite8(priv, (u8 *) rtl8187b_ac_addr[queue],
1148                                          priv->aifsn[queue] * priv->slot_time +
1149                                          SIFS_TIME);
1150         } else {
1151                 rtl818x_iowrite8(priv, &priv->map->SIFS, 0x22);
1152                 if (use_short_slot) {
1153                         rtl818x_iowrite8(priv, &priv->map->SLOT, 0x9);
1154                         rtl818x_iowrite8(priv, &priv->map->DIFS, 0x14);
1155                         rtl818x_iowrite8(priv, &priv->map->EIFS, 91 - 0x14);
1156                 } else {
1157                         rtl818x_iowrite8(priv, &priv->map->SLOT, 0x14);
1158                         rtl818x_iowrite8(priv, &priv->map->DIFS, 0x24);
1159                         rtl818x_iowrite8(priv, &priv->map->EIFS, 91 - 0x24);
1160                 }
1161         }
1162 }
1163
1164 static void rtl8187_bss_info_changed(struct ieee80211_hw *dev,
1165                                      struct ieee80211_vif *vif,
1166                                      struct ieee80211_bss_conf *info,
1167                                      u32 changed)
1168 {
1169         struct rtl8187_priv *priv = dev->priv;
1170         int i;
1171         u8 reg;
1172
1173         if (changed & BSS_CHANGED_BSSID) {
1174                 mutex_lock(&priv->conf_mutex);
1175                 for (i = 0; i < ETH_ALEN; i++)
1176                         rtl818x_iowrite8(priv, &priv->map->BSSID[i],
1177                                          info->bssid[i]);
1178
1179                 if (priv->is_rtl8187b)
1180                         reg = RTL818X_MSR_ENEDCA;
1181                 else
1182                         reg = 0;
1183
1184                 if (is_valid_ether_addr(info->bssid)) {
1185                         reg |= RTL818X_MSR_INFRA;
1186                         rtl818x_iowrite8(priv, &priv->map->MSR, reg);
1187                 } else {
1188                         reg |= RTL818X_MSR_NO_LINK;
1189                         rtl818x_iowrite8(priv, &priv->map->MSR, reg);
1190                 }
1191
1192                 mutex_unlock(&priv->conf_mutex);
1193         }
1194
1195         if (changed & (BSS_CHANGED_ERP_SLOT | BSS_CHANGED_ERP_PREAMBLE))
1196                 rtl8187_conf_erp(priv, info->use_short_slot,
1197                                  info->use_short_preamble);
1198 }
1199
1200 static void rtl8187_configure_filter(struct ieee80211_hw *dev,
1201                                      unsigned int changed_flags,
1202                                      unsigned int *total_flags,
1203                                      int mc_count, struct dev_addr_list *mclist)
1204 {
1205         struct rtl8187_priv *priv = dev->priv;
1206
1207         if (changed_flags & FIF_FCSFAIL)
1208                 priv->rx_conf ^= RTL818X_RX_CONF_FCS;
1209         if (changed_flags & FIF_CONTROL)
1210                 priv->rx_conf ^= RTL818X_RX_CONF_CTRL;
1211         if (changed_flags & FIF_OTHER_BSS)
1212                 priv->rx_conf ^= RTL818X_RX_CONF_MONITOR;
1213         if (*total_flags & FIF_ALLMULTI || mc_count > 0)
1214                 priv->rx_conf |= RTL818X_RX_CONF_MULTICAST;
1215         else
1216                 priv->rx_conf &= ~RTL818X_RX_CONF_MULTICAST;
1217
1218         *total_flags = 0;
1219
1220         if (priv->rx_conf & RTL818X_RX_CONF_FCS)
1221                 *total_flags |= FIF_FCSFAIL;
1222         if (priv->rx_conf & RTL818X_RX_CONF_CTRL)
1223                 *total_flags |= FIF_CONTROL;
1224         if (priv->rx_conf & RTL818X_RX_CONF_MONITOR)
1225                 *total_flags |= FIF_OTHER_BSS;
1226         if (priv->rx_conf & RTL818X_RX_CONF_MULTICAST)
1227                 *total_flags |= FIF_ALLMULTI;
1228
1229         rtl818x_iowrite32_async(priv, &priv->map->RX_CONF, priv->rx_conf);
1230 }
1231
1232 static int rtl8187_conf_tx(struct ieee80211_hw *dev, u16 queue,
1233                            const struct ieee80211_tx_queue_params *params)
1234 {
1235         struct rtl8187_priv *priv = dev->priv;
1236         u8 cw_min, cw_max;
1237
1238         if (queue > 3)
1239                 return -EINVAL;
1240
1241         cw_min = fls(params->cw_min);
1242         cw_max = fls(params->cw_max);
1243
1244         if (priv->is_rtl8187b) {
1245                 priv->aifsn[queue] = params->aifs;
1246
1247                 /*
1248                  * This is the structure of AC_*_PARAM registers in 8187B:
1249                  * - TXOP limit field, bit offset = 16
1250                  * - ECWmax, bit offset = 12
1251                  * - ECWmin, bit offset = 8
1252                  * - AIFS, bit offset = 0
1253                  */
1254                 rtl818x_iowrite32(priv, rtl8187b_ac_addr[queue],
1255                                   (params->txop << 16) | (cw_max << 12) |
1256                                   (cw_min << 8) | (params->aifs *
1257                                   priv->slot_time + SIFS_TIME));
1258         } else {
1259                 if (queue != 0)
1260                         return -EINVAL;
1261
1262                 rtl818x_iowrite8(priv, &priv->map->CW_VAL,
1263                                  cw_min | (cw_max << 4));
1264         }
1265         return 0;
1266 }
1267
1268 static const struct ieee80211_ops rtl8187_ops = {
1269         .tx                     = rtl8187_tx,
1270         .start                  = rtl8187_start,
1271         .stop                   = rtl8187_stop,
1272         .add_interface          = rtl8187_add_interface,
1273         .remove_interface       = rtl8187_remove_interface,
1274         .config                 = rtl8187_config,
1275         .bss_info_changed       = rtl8187_bss_info_changed,
1276         .configure_filter       = rtl8187_configure_filter,
1277         .conf_tx                = rtl8187_conf_tx
1278 };
1279
1280 static void rtl8187_eeprom_register_read(struct eeprom_93cx6 *eeprom)
1281 {
1282         struct ieee80211_hw *dev = eeprom->data;
1283         struct rtl8187_priv *priv = dev->priv;
1284         u8 reg = rtl818x_ioread8(priv, &priv->map->EEPROM_CMD);
1285
1286         eeprom->reg_data_in = reg & RTL818X_EEPROM_CMD_WRITE;
1287         eeprom->reg_data_out = reg & RTL818X_EEPROM_CMD_READ;
1288         eeprom->reg_data_clock = reg & RTL818X_EEPROM_CMD_CK;
1289         eeprom->reg_chip_select = reg & RTL818X_EEPROM_CMD_CS;
1290 }
1291
1292 static void rtl8187_eeprom_register_write(struct eeprom_93cx6 *eeprom)
1293 {
1294         struct ieee80211_hw *dev = eeprom->data;
1295         struct rtl8187_priv *priv = dev->priv;
1296         u8 reg = RTL818X_EEPROM_CMD_PROGRAM;
1297
1298         if (eeprom->reg_data_in)
1299                 reg |= RTL818X_EEPROM_CMD_WRITE;
1300         if (eeprom->reg_data_out)
1301                 reg |= RTL818X_EEPROM_CMD_READ;
1302         if (eeprom->reg_data_clock)
1303                 reg |= RTL818X_EEPROM_CMD_CK;
1304         if (eeprom->reg_chip_select)
1305                 reg |= RTL818X_EEPROM_CMD_CS;
1306
1307         rtl818x_iowrite8(priv, &priv->map->EEPROM_CMD, reg);
1308         udelay(10);
1309 }
1310
1311 static int __devinit rtl8187_probe(struct usb_interface *intf,
1312                                    const struct usb_device_id *id)
1313 {
1314         struct usb_device *udev = interface_to_usbdev(intf);
1315         struct ieee80211_hw *dev;
1316         struct rtl8187_priv *priv;
1317         struct eeprom_93cx6 eeprom;
1318         struct ieee80211_channel *channel;
1319         const char *chip_name;
1320         u16 txpwr, reg;
1321         int err, i;
1322
1323         dev = ieee80211_alloc_hw(sizeof(*priv), &rtl8187_ops);
1324         if (!dev) {
1325                 printk(KERN_ERR "rtl8187: ieee80211 alloc failed\n");
1326                 return -ENOMEM;
1327         }
1328
1329         priv = dev->priv;
1330         priv->is_rtl8187b = (id->driver_info == DEVICE_RTL8187B);
1331
1332         /* allocate "DMA aware" buffer for register accesses */
1333         priv->io_dmabuf = kmalloc(sizeof(*priv->io_dmabuf), GFP_KERNEL);
1334         if (!priv->io_dmabuf) {
1335                 err = -ENOMEM;
1336                 goto err_free_dev;
1337         }
1338         mutex_init(&priv->io_mutex);
1339
1340         SET_IEEE80211_DEV(dev, &intf->dev);
1341         usb_set_intfdata(intf, dev);
1342         priv->udev = udev;
1343
1344         usb_get_dev(udev);
1345
1346         skb_queue_head_init(&priv->rx_queue);
1347
1348         BUILD_BUG_ON(sizeof(priv->channels) != sizeof(rtl818x_channels));
1349         BUILD_BUG_ON(sizeof(priv->rates) != sizeof(rtl818x_rates));
1350
1351         memcpy(priv->channels, rtl818x_channels, sizeof(rtl818x_channels));
1352         memcpy(priv->rates, rtl818x_rates, sizeof(rtl818x_rates));
1353         priv->map = (struct rtl818x_csr *)0xFF00;
1354
1355         priv->band.band = IEEE80211_BAND_2GHZ;
1356         priv->band.channels = priv->channels;
1357         priv->band.n_channels = ARRAY_SIZE(rtl818x_channels);
1358         priv->band.bitrates = priv->rates;
1359         priv->band.n_bitrates = ARRAY_SIZE(rtl818x_rates);
1360         dev->wiphy->bands[IEEE80211_BAND_2GHZ] = &priv->band;
1361
1362
1363         priv->mode = NL80211_IFTYPE_MONITOR;
1364         dev->flags = IEEE80211_HW_HOST_BROADCAST_PS_BUFFERING |
1365                      IEEE80211_HW_SIGNAL_DBM |
1366                      IEEE80211_HW_RX_INCLUDES_FCS;
1367
1368         eeprom.data = dev;
1369         eeprom.register_read = rtl8187_eeprom_register_read;
1370         eeprom.register_write = rtl8187_eeprom_register_write;
1371         if (rtl818x_ioread32(priv, &priv->map->RX_CONF) & (1 << 6))
1372                 eeprom.width = PCI_EEPROM_WIDTH_93C66;
1373         else
1374                 eeprom.width = PCI_EEPROM_WIDTH_93C46;
1375
1376         rtl818x_iowrite8(priv, &priv->map->EEPROM_CMD, RTL818X_EEPROM_CMD_CONFIG);
1377         udelay(10);
1378
1379         eeprom_93cx6_multiread(&eeprom, RTL8187_EEPROM_MAC_ADDR,
1380                                (__le16 __force *)dev->wiphy->perm_addr, 3);
1381         if (!is_valid_ether_addr(dev->wiphy->perm_addr)) {
1382                 printk(KERN_WARNING "rtl8187: Invalid hwaddr! Using randomly "
1383                        "generated MAC address\n");
1384                 random_ether_addr(dev->wiphy->perm_addr);
1385         }
1386
1387         channel = priv->channels;
1388         for (i = 0; i < 3; i++) {
1389                 eeprom_93cx6_read(&eeprom, RTL8187_EEPROM_TXPWR_CHAN_1 + i,
1390                                   &txpwr);
1391                 (*channel++).hw_value = txpwr & 0xFF;
1392                 (*channel++).hw_value = txpwr >> 8;
1393         }
1394         for (i = 0; i < 2; i++) {
1395                 eeprom_93cx6_read(&eeprom, RTL8187_EEPROM_TXPWR_CHAN_4 + i,
1396                                   &txpwr);
1397                 (*channel++).hw_value = txpwr & 0xFF;
1398                 (*channel++).hw_value = txpwr >> 8;
1399         }
1400
1401         eeprom_93cx6_read(&eeprom, RTL8187_EEPROM_TXPWR_BASE,
1402                           &priv->txpwr_base);
1403
1404         reg = rtl818x_ioread8(priv, &priv->map->PGSELECT) & ~1;
1405         rtl818x_iowrite8(priv, &priv->map->PGSELECT, reg | 1);
1406         /* 0 means asic B-cut, we should use SW 3 wire
1407          * bit-by-bit banging for radio. 1 means we can use
1408          * USB specific request to write radio registers */
1409         priv->asic_rev = rtl818x_ioread8(priv, (u8 *)0xFFFE) & 0x3;
1410         rtl818x_iowrite8(priv, &priv->map->PGSELECT, reg);
1411         rtl818x_iowrite8(priv, &priv->map->EEPROM_CMD, RTL818X_EEPROM_CMD_NORMAL);
1412
1413         if (!priv->is_rtl8187b) {
1414                 u32 reg32;
1415                 reg32 = rtl818x_ioread32(priv, &priv->map->TX_CONF);
1416                 reg32 &= RTL818X_TX_CONF_HWVER_MASK;
1417                 switch (reg32) {
1418                 case RTL818X_TX_CONF_R8187vD_B:
1419                         /* Some RTL8187B devices have a USB ID of 0x8187
1420                          * detect them here */
1421                         chip_name = "RTL8187BvB(early)";
1422                         priv->is_rtl8187b = 1;
1423                         priv->hw_rev = RTL8187BvB;
1424                         break;
1425                 case RTL818X_TX_CONF_R8187vD:
1426                         chip_name = "RTL8187vD";
1427                         break;
1428                 default:
1429                         chip_name = "RTL8187vB (default)";
1430                 }
1431        } else {
1432                 /*
1433                  * Force USB request to write radio registers for 8187B, Realtek
1434                  * only uses it in their sources
1435                  */
1436                 /*if (priv->asic_rev == 0) {
1437                         printk(KERN_WARNING "rtl8187: Forcing use of USB "
1438                                "requests to write to radio registers\n");
1439                         priv->asic_rev = 1;
1440                 }*/
1441                 switch (rtl818x_ioread8(priv, (u8 *)0xFFE1)) {
1442                 case RTL818X_R8187B_B:
1443                         chip_name = "RTL8187BvB";
1444                         priv->hw_rev = RTL8187BvB;
1445                         break;
1446                 case RTL818X_R8187B_D:
1447                         chip_name = "RTL8187BvD";
1448                         priv->hw_rev = RTL8187BvD;
1449                         break;
1450                 case RTL818X_R8187B_E:
1451                         chip_name = "RTL8187BvE";
1452                         priv->hw_rev = RTL8187BvE;
1453                         break;
1454                 default:
1455                         chip_name = "RTL8187BvB (default)";
1456                         priv->hw_rev = RTL8187BvB;
1457                 }
1458         }
1459
1460         if (!priv->is_rtl8187b) {
1461                 for (i = 0; i < 2; i++) {
1462                         eeprom_93cx6_read(&eeprom,
1463                                           RTL8187_EEPROM_TXPWR_CHAN_6 + i,
1464                                           &txpwr);
1465                         (*channel++).hw_value = txpwr & 0xFF;
1466                         (*channel++).hw_value = txpwr >> 8;
1467                 }
1468         } else {
1469                 eeprom_93cx6_read(&eeprom, RTL8187_EEPROM_TXPWR_CHAN_6,
1470                                   &txpwr);
1471                 (*channel++).hw_value = txpwr & 0xFF;
1472
1473                 eeprom_93cx6_read(&eeprom, 0x0A, &txpwr);
1474                 (*channel++).hw_value = txpwr & 0xFF;
1475
1476                 eeprom_93cx6_read(&eeprom, 0x1C, &txpwr);
1477                 (*channel++).hw_value = txpwr & 0xFF;
1478                 (*channel++).hw_value = txpwr >> 8;
1479         }
1480
1481         /*
1482          * XXX: Once this driver supports anything that requires
1483          *      beacons it must implement IEEE80211_TX_CTL_ASSIGN_SEQ.
1484          */
1485         dev->wiphy->interface_modes = BIT(NL80211_IFTYPE_STATION);
1486
1487         if ((id->driver_info == DEVICE_RTL8187) && priv->is_rtl8187b)
1488                 printk(KERN_INFO "rtl8187: inconsistency between id with OEM"
1489                        " info!\n");
1490
1491         priv->rf = rtl8187_detect_rf(dev);
1492         dev->extra_tx_headroom = (!priv->is_rtl8187b) ?
1493                                   sizeof(struct rtl8187_tx_hdr) :
1494                                   sizeof(struct rtl8187b_tx_hdr);
1495         if (!priv->is_rtl8187b)
1496                 dev->queues = 1;
1497         else
1498                 dev->queues = 4;
1499
1500         err = ieee80211_register_hw(dev);
1501         if (err) {
1502                 printk(KERN_ERR "rtl8187: Cannot register device\n");
1503                 goto err_free_dmabuf;
1504         }
1505         mutex_init(&priv->conf_mutex);
1506         skb_queue_head_init(&priv->b_tx_status.queue);
1507
1508         printk(KERN_INFO "%s: hwaddr %pM, %s V%d + %s\n",
1509                wiphy_name(dev->wiphy), dev->wiphy->perm_addr,
1510                chip_name, priv->asic_rev, priv->rf->name);
1511
1512 #ifdef CONFIG_RTL8187_LEDS
1513         eeprom_93cx6_read(&eeprom, 0x3F, &reg);
1514         reg &= 0xFF;
1515         rtl8187_leds_init(dev, reg);
1516 #endif
1517
1518         return 0;
1519
1520  err_free_dmabuf:
1521         kfree(priv->io_dmabuf);
1522  err_free_dev:
1523         ieee80211_free_hw(dev);
1524         usb_set_intfdata(intf, NULL);
1525         usb_put_dev(udev);
1526         return err;
1527 }
1528
1529 static void __devexit rtl8187_disconnect(struct usb_interface *intf)
1530 {
1531         struct ieee80211_hw *dev = usb_get_intfdata(intf);
1532         struct rtl8187_priv *priv;
1533
1534         if (!dev)
1535                 return;
1536
1537 #ifdef CONFIG_RTL8187_LEDS
1538         rtl8187_leds_exit(dev);
1539 #endif
1540         ieee80211_unregister_hw(dev);
1541
1542         priv = dev->priv;
1543         usb_reset_device(priv->udev);
1544         usb_put_dev(interface_to_usbdev(intf));
1545         kfree(priv->io_dmabuf);
1546         ieee80211_free_hw(dev);
1547 }
1548
1549 static struct usb_driver rtl8187_driver = {
1550         .name           = KBUILD_MODNAME,
1551         .id_table       = rtl8187_table,
1552         .probe          = rtl8187_probe,
1553         .disconnect     = __devexit_p(rtl8187_disconnect),
1554 };
1555
1556 static int __init rtl8187_init(void)
1557 {
1558         return usb_register(&rtl8187_driver);
1559 }
1560
1561 static void __exit rtl8187_exit(void)
1562 {
1563         usb_deregister(&rtl8187_driver);
1564 }
1565
1566 module_init(rtl8187_init);
1567 module_exit(rtl8187_exit);