drivers/net/sungem_phy.c

   1 /*
   2  * PHY drivers for the sungem ethernet driver.
   3  *
   4  * This file could be shared with other drivers.
   5  *
   6  * (c) 2002, Benjamin Herrenscmidt (benh@kernel.crashing.org)
   7  *
   8  * TODO:
   9  *  - Implement WOL
  10  *  - Add support for PHYs that provide an IRQ line
  11  *  - Eventually moved the entire polling state machine in
  12  *    there (out of the eth driver), so that it can easily be
  13  *    skipped on PHYs that implement it in hardware.
  14  *  - On LXT971 & BCM5201, Apple uses some chip specific regs
  15  *    to read the link status. Figure out why and if it makes
  16  *    sense to do the same (magic aneg ?)
  17  *  - Apple has some additional power management code for some
  18  *    Broadcom PHYs that they "hide" from the OpenSource version
  19  *    of darwin, still need to reverse engineer that
  20  */
  21
  22 #include <linux/config.h>
  23
  24 #include <linux/module.h>
  25
  26 #include <linux/kernel.h>
  27 #include <linux/sched.h>
  28 #include <linux/types.h>
  29 #include <linux/netdevice.h>
  30 #include <linux/etherdevice.h>
  31 #include <linux/mii.h>
  32 #include <linux/ethtool.h>
  33 #include <linux/delay.h>
  34
  35 #ifdef CONFIG_PPC_PMAC
  36 #include <asm/prom.h>
  37 #endif
  38
  39 #include "sungem_phy.h"
  40
  41 /* Link modes of the BCM5400 PHY */
  42 static const int phy_BCM5400_link_table[8][3] = {
  43         { 0, 0, 0 },    /* No link */
  44         { 0, 0, 0 },    /* 10BT Half Duplex */
  45         { 1, 0, 0 },    /* 10BT Full Duplex */
  46         { 0, 1, 0 },    /* 100BT Half Duplex */
  47         { 0, 1, 0 },    /* 100BT Half Duplex */
  48         { 1, 1, 0 },    /* 100BT Full Duplex*/
  49         { 1, 0, 1 },    /* 1000BT */
  50         { 1, 0, 1 },    /* 1000BT */
  51 };
  52
  53 static inline int __phy_read(struct mii_phy* phy, int id, int reg)
  54 {
  55         return phy->mdio_read(phy->dev, id, reg);
  56 }
  57
  58 static inline void __phy_write(struct mii_phy* phy, int id, int reg, int val)
  59 {
  60         phy->mdio_write(phy->dev, id, reg, val);
  61 }
  62
  63 static inline int phy_read(struct mii_phy* phy, int reg)
  64 {
  65         return phy->mdio_read(phy->dev, phy->mii_id, reg);
  66 }
  67
  68 static inline void phy_write(struct mii_phy* phy, int reg, int val)
  69 {
  70         phy->mdio_write(phy->dev, phy->mii_id, reg, val);
  71 }
  72
  73 static int reset_one_mii_phy(struct mii_phy* phy, int phy_id)
  74 {
  75         u16 val;
  76         int limit = 10000;
  77
  78         val = __phy_read(phy, phy_id, MII_BMCR);
  79         val &= ~(BMCR_ISOLATE | BMCR_PDOWN);
  80         val |= BMCR_RESET;
  81         __phy_write(phy, phy_id, MII_BMCR, val);
  82
  83         udelay(100);
  84
  85         while (limit--) {
  86                 val = __phy_read(phy, phy_id, MII_BMCR);
  87                 if ((val & BMCR_RESET) == 0)
  88                         break;
  89                 udelay(10);
  90         }
  91         if ((val & BMCR_ISOLATE) && limit > 0)
  92                 __phy_write(phy, phy_id, MII_BMCR, val & ~BMCR_ISOLATE);
  93
  94         return (limit <= 0);
  95 }
  96
  97 static int bcm5201_init(struct mii_phy* phy)
  98 {
  99         u16 data;
 100
 101         data = phy_read(phy, MII_BCM5201_MULTIPHY);
 102         data &= ~MII_BCM5201_MULTIPHY_SUPERISOLATE;
 103         phy_write(phy, MII_BCM5201_MULTIPHY, data);
 104
 105         phy_write(phy, MII_BCM5201_INTERRUPT, 0);
 106
 107         return 0;
 108 }
 109
 110 static int bcm5201_suspend(struct mii_phy* phy)
 111 {
 112         phy_write(phy, MII_BCM5201_INTERRUPT, 0);
 113         phy_write(phy, MII_BCM5201_MULTIPHY, MII_BCM5201_MULTIPHY_SUPERISOLATE);
 114
 115         return 0;
 116 }
 117
 118 static int bcm5221_init(struct mii_phy* phy)
 119 {
 120         u16 data;
 121
 122         data = phy_read(phy, MII_BCM5221_TEST);
 123         phy_write(phy, MII_BCM5221_TEST,
 124                 data | MII_BCM5221_TEST_ENABLE_SHADOWS);
 125
 126         data = phy_read(phy, MII_BCM5221_SHDOW_AUX_STAT2);
 127         phy_write(phy, MII_BCM5221_SHDOW_AUX_STAT2,
 128                 data | MII_BCM5221_SHDOW_AUX_STAT2_APD);
 129
 130         data = phy_read(phy, MII_BCM5221_SHDOW_AUX_MODE4);
 131         phy_write(phy, MII_BCM5221_SHDOW_AUX_MODE4,
 132                 data | MII_BCM5221_SHDOW_AUX_MODE4_CLKLOPWR);
 133
 134         data = phy_read(phy, MII_BCM5221_TEST);
 135         phy_write(phy, MII_BCM5221_TEST,
 136                 data & ~MII_BCM5221_TEST_ENABLE_SHADOWS);
 137
 138         return 0;
 139 }
 140
 141 static int bcm5221_suspend(struct mii_phy* phy)
 142 {
 143         u16 data;
 144
 145         data = phy_read(phy, MII_BCM5221_TEST);
 146         phy_write(phy, MII_BCM5221_TEST,
 147                 data | MII_BCM5221_TEST_ENABLE_SHADOWS);
 148
 149         data = phy_read(phy, MII_BCM5221_SHDOW_AUX_MODE4);
 150         phy_write(phy, MII_BCM5221_SHDOW_AUX_MODE4,
 151                   data | MII_BCM5221_SHDOW_AUX_MODE4_IDDQMODE);
 152
 153         return 0;
 154 }
 155
 156 static int bcm5400_init(struct mii_phy* phy)
 157 {
 158         u16 data;
 159
 160         /* Configure for gigabit full duplex */
 161         data = phy_read(phy, MII_BCM5400_AUXCONTROL);
 162         data |= MII_BCM5400_AUXCONTROL_PWR10BASET;
 163         phy_write(phy, MII_BCM5400_AUXCONTROL, data);
 164
 165         data = phy_read(phy, MII_BCM5400_GB_CONTROL);
 166         data |= MII_BCM5400_GB_CONTROL_FULLDUPLEXCAP;
 167         phy_write(phy, MII_BCM5400_GB_CONTROL, data);
 168
 169         udelay(100);
 170
 171         /* Reset and configure cascaded 10/100 PHY */
 172         (void)reset_one_mii_phy(phy, 0x1f);
 173
 174         data = __phy_read(phy, 0x1f, MII_BCM5201_MULTIPHY);
 175         data |= MII_BCM5201_MULTIPHY_SERIALMODE;
 176         __phy_write(phy, 0x1f, MII_BCM5201_MULTIPHY, data);
 177
 178         data = phy_read(phy, MII_BCM5400_AUXCONTROL);
 179         data &= ~MII_BCM5400_AUXCONTROL_PWR10BASET;
 180         phy_write(phy, MII_BCM5400_AUXCONTROL, data);
 181
 182         return 0;
 183 }
 184
 185 static int bcm5400_suspend(struct mii_phy* phy)
 186 {
 187 #if 0 /* Commented out in Darwin... someone has those dawn docs ? */
 188         phy_write(phy, MII_BMCR, BMCR_PDOWN);
 189 #endif
 190         return 0;
 191 }
 192
 193 static int bcm5401_init(struct mii_phy* phy)
 194 {
 195         u16 data;
 196         int rev;
 197
 198         rev = phy_read(phy, MII_PHYSID2) & 0x000f;
 199         if (rev == 0 || rev == 3) {
 200                 /* Some revisions of 5401 appear to need this
 201                  * initialisation sequence to disable, according
 202                  * to OF, "tap power management"
 203                  *
 204                  * WARNING ! OF and Darwin don't agree on the
 205                  * register addresses. OF seem to interpret the
 206                  * register numbers below as decimal
 207                  *
 208                  * Note: This should (and does) match tg3_init_5401phy_dsp
 209                  *       in the tg3.c driver. -DaveM
 210                  */
 211                 phy_write(phy, 0x18, 0x0c20);
 212                 phy_write(phy, 0x17, 0x0012);
 213                 phy_write(phy, 0x15, 0x1804);
 214                 phy_write(phy, 0x17, 0x0013);
 215                 phy_write(phy, 0x15, 0x1204);
 216                 phy_write(phy, 0x17, 0x8006);
 217                 phy_write(phy, 0x15, 0x0132);
 218                 phy_write(phy, 0x17, 0x8006);
 219                 phy_write(phy, 0x15, 0x0232);
 220                 phy_write(phy, 0x17, 0x201f);
 221                 phy_write(phy, 0x15, 0x0a20);
 222         }
 223
 224         /* Configure for gigabit full duplex */
 225         data = phy_read(phy, MII_BCM5400_GB_CONTROL);
 226         data |= MII_BCM5400_GB_CONTROL_FULLDUPLEXCAP;
 227         phy_write(phy, MII_BCM5400_GB_CONTROL, data);
 228
 229         udelay(10);
 230
 231         /* Reset and configure cascaded 10/100 PHY */
 232         (void)reset_one_mii_phy(phy, 0x1f);
 233
 234         data = __phy_read(phy, 0x1f, MII_BCM5201_MULTIPHY);
 235         data |= MII_BCM5201_MULTIPHY_SERIALMODE;
 236         __phy_write(phy, 0x1f, MII_BCM5201_MULTIPHY, data);
 237
 238         return 0;
 239 }
 240
 241 static int bcm5401_suspend(struct mii_phy* phy)
 242 {
 243 #if 0 /* Commented out in Darwin... someone has those dawn docs ? */
 244         phy_write(phy, MII_BMCR, BMCR_PDOWN);
 245 #endif
 246         return 0;
 247 }
 248
 249 static int bcm5411_init(struct mii_phy* phy)
 250 {
 251         u16 data;
 252
 253         /* Here's some more Apple black magic to setup
 254          * some voltage stuffs.
 255          */
 256         phy_write(phy, 0x1c, 0x8c23);
 257         phy_write(phy, 0x1c, 0x8ca3);
 258         phy_write(phy, 0x1c, 0x8c23);
 259
 260         /* Here, Apple seems to want to reset it, do
 261          * it as well
 262          */
 263         phy_write(phy, MII_BMCR, BMCR_RESET);
 264         phy_write(phy, MII_BMCR, 0x1340);
 265
 266         data = phy_read(phy, MII_BCM5400_GB_CONTROL);
 267         data |= MII_BCM5400_GB_CONTROL_FULLDUPLEXCAP;
 268         phy_write(phy, MII_BCM5400_GB_CONTROL, data);
 269
 270         udelay(10);
 271
 272         /* Reset and configure cascaded 10/100 PHY */
 273         (void)reset_one_mii_phy(phy, 0x1f);
 274
 275         return 0;
 276 }
 277
 278 static int generic_suspend(struct mii_phy* phy)
 279 {
 280         phy_write(phy, MII_BMCR, BMCR_PDOWN);
 281
 282         return 0;
 283 }
 284
 285 static int bcm5421_init(struct mii_phy* phy)
 286 {
 287         u16 data;
 288         unsigned int id;
 289
 290         id = (phy_read(phy, MII_PHYSID1) << 16 | phy_read(phy, MII_PHYSID2));
 291
 292         /* Revision 0 of 5421 needs some fixups */
 293         if (id == 0x002060e0) {
 294                 /* This is borrowed from MacOS
 295                  */
 296                 phy_write(phy, 0x18, 0x1007);
 297                 data = phy_read(phy, 0x18);
 298                 phy_write(phy, 0x18, data | 0x0400);
 299                 phy_write(phy, 0x18, 0x0007);
 300                 data = phy_read(phy, 0x18);
 301                 phy_write(phy, 0x18, data | 0x0800);
 302                 phy_write(phy, 0x17, 0x000a);
 303                 data = phy_read(phy, 0x15);
 304                 phy_write(phy, 0x15, data | 0x0200);
 305         }
 306
 307         /* Pick up some init code from OF for K2 version */
 308         if ((id & 0xfffffff0) == 0x002062e0) {
 309                 phy_write(phy, 4, 0x01e1);
 310                 phy_write(phy, 9, 0x0300);
 311         }
 312
 313         /* Check if we can enable automatic low power */
 314 #ifdef CONFIG_PPC_PMAC
 315         if (phy->platform_data) {
 316                 struct device_node *np = of_get_parent(phy->platform_data);
 317                 int can_low_power = 1;
 318                 if (np == NULL || get_property(np, "no-autolowpower", NULL))
 319                         can_low_power = 0;
 320                 if (can_low_power) {
 321                         /* Enable automatic low-power */
 322                         phy_write(phy, 0x1c, 0x9002);
 323                         phy_write(phy, 0x1c, 0xa821);
 324                         phy_write(phy, 0x1c, 0x941d);
 325                 }
 326         }
 327 #endif /* CONFIG_PPC_PMAC */
 328
 329         return 0;
 330 }
 331
 332 static int bcm54xx_setup_aneg(struct mii_phy *phy, u32 advertise)
 333 {
 334         u16 ctl, adv;
 335
 336         phy->autoneg = 1;
 337         phy->speed = SPEED_10;
 338         phy->duplex = DUPLEX_HALF;
 339         phy->pause = 0;
 340         phy->advertising = advertise;
 341
 342         /* Setup standard advertise */
 343         adv = phy_read(phy, MII_ADVERTISE);
 344         adv &= ~(ADVERTISE_ALL | ADVERTISE_100BASE4);
 345         if (advertise & ADVERTISED_10baseT_Half)
 346                 adv |= ADVERTISE_10HALF;
 347         if (advertise & ADVERTISED_10baseT_Full)
 348                 adv |= ADVERTISE_10FULL;
 349         if (advertise & ADVERTISED_100baseT_Half)
 350                 adv |= ADVERTISE_100HALF;
 351         if (advertise & ADVERTISED_100baseT_Full)
 352                 adv |= ADVERTISE_100FULL;
 353         phy_write(phy, MII_ADVERTISE, adv);
 354
 355         /* Setup 1000BT advertise */
 356         adv = phy_read(phy, MII_1000BASETCONTROL);
 357         adv &= ~(MII_1000BASETCONTROL_FULLDUPLEXCAP|MII_1000BASETCONTROL_HALFDUPLEXCAP);
 358         if (advertise & SUPPORTED_1000baseT_Half)
 359                 adv |= MII_1000BASETCONTROL_HALFDUPLEXCAP;
 360         if (advertise & SUPPORTED_1000baseT_Full)
 361                 adv |= MII_1000BASETCONTROL_FULLDUPLEXCAP;
 362         phy_write(phy, MII_1000BASETCONTROL, adv);
 363
 364         /* Start/Restart aneg */
 365         ctl = phy_read(phy, MII_BMCR);
 366         ctl |= (BMCR_ANENABLE | BMCR_ANRESTART);
 367         phy_write(phy, MII_BMCR, ctl);
 368
 369         return 0;
 370 }
 371
 372 static int bcm54xx_setup_forced(struct mii_phy *phy, int speed, int fd)
 373 {
 374         u16 ctl;
 375
 376         phy->autoneg = 0;
 377         phy->speed = speed;
 378         phy->duplex = fd;
 379         phy->pause = 0;
 380
 381         ctl = phy_read(phy, MII_BMCR);
 382         ctl &= ~(BMCR_FULLDPLX|BMCR_SPEED100|BMCR_SPD2|BMCR_ANENABLE);
 383
 384         /* First reset the PHY */
 385         phy_write(phy, MII_BMCR, ctl | BMCR_RESET);
 386
 387         /* Select speed & duplex */
 388         switch(speed) {
 389         case SPEED_10:
 390                 break;
 391         case SPEED_100:
 392                 ctl |= BMCR_SPEED100;
 393                 break;
 394         case SPEED_1000:
 395                 ctl |= BMCR_SPD2;
 396         }
 397         if (fd == DUPLEX_FULL)
 398                 ctl |= BMCR_FULLDPLX;
 399
 400         // XXX Should we set the sungem to GII now on 1000BT ?
 401
 402         phy_write(phy, MII_BMCR, ctl);
 403
 404         return 0;
 405 }
 406
 407 static int bcm54xx_read_link(struct mii_phy *phy)
 408 {
 409         int link_mode;
 410         u16 val;
 411
 412         if (phy->autoneg) {
 413                 val = phy_read(phy, MII_BCM5400_AUXSTATUS);
 414                 link_mode = ((val & MII_BCM5400_AUXSTATUS_LINKMODE_MASK) >>
 415                              MII_BCM5400_AUXSTATUS_LINKMODE_SHIFT);
 416                 phy->duplex = phy_BCM5400_link_table[link_mode][0] ? DUPLEX_FULL : DUPLEX_HALF;
 417                 phy->speed = phy_BCM5400_link_table[link_mode][2] ?
 418                                 SPEED_1000 :
 419                                 (phy_BCM5400_link_table[link_mode][1] ? SPEED_100 : SPEED_10);
 420                 val = phy_read(phy, MII_LPA);
 421                 phy->pause = ((val & LPA_PAUSE) != 0);
 422         }
 423         /* On non-aneg, we assume what we put in BMCR is the speed,
 424          * though magic-aneg shouldn't prevent this case from occurring
 425          */
 426
 427         return 0;
 428 }
 429
 430 static int marvell_setup_aneg(struct mii_phy *phy, u32 advertise)
 431 {
 432         u16 ctl, adv;
 433
 434         phy->autoneg = 1;
 435         phy->speed = SPEED_10;
 436         phy->duplex = DUPLEX_HALF;
 437         phy->pause = 0;
 438         phy->advertising = advertise;
 439
 440         /* Setup standard advertise */
 441         adv = phy_read(phy, MII_ADVERTISE);
 442         adv &= ~(ADVERTISE_ALL | ADVERTISE_100BASE4);
 443         if (advertise & ADVERTISED_10baseT_Half)
 444                 adv |= ADVERTISE_10HALF;
 445         if (advertise & ADVERTISED_10baseT_Full)
 446                 adv |= ADVERTISE_10FULL;
 447         if (advertise & ADVERTISED_100baseT_Half)
 448                 adv |= ADVERTISE_100HALF;
 449         if (advertise & ADVERTISED_100baseT_Full)
 450                 adv |= ADVERTISE_100FULL;
 451         phy_write(phy, MII_ADVERTISE, adv);
 452
 453         /* Setup 1000BT advertise & enable crossover detect
 454          * XXX How do we advertise 1000BT ? Darwin source is
 455          * confusing here, they read from specific control and
 456          * write to control... Someone has specs for those
 457          * beasts ?
 458          */
 459         adv = phy_read(phy, MII_M1011_PHY_SPEC_CONTROL);
 460         adv |= MII_M1011_PHY_SPEC_CONTROL_AUTO_MDIX;
 461         adv &= ~(MII_1000BASETCONTROL_FULLDUPLEXCAP |
 462                         MII_1000BASETCONTROL_HALFDUPLEXCAP);
 463         if (advertise & SUPPORTED_1000baseT_Half)
 464                 adv |= MII_1000BASETCONTROL_HALFDUPLEXCAP;
 465         if (advertise & SUPPORTED_1000baseT_Full)
 466                 adv |= MII_1000BASETCONTROL_FULLDUPLEXCAP;
 467         phy_write(phy, MII_1000BASETCONTROL, adv);
 468
 469         /* Start/Restart aneg */
 470         ctl = phy_read(phy, MII_BMCR);
 471         ctl |= (BMCR_ANENABLE | BMCR_ANRESTART);
 472         phy_write(phy, MII_BMCR, ctl);
 473
 474         return 0;
 475 }
 476
 477 static int marvell_setup_forced(struct mii_phy *phy, int speed, int fd)
 478 {
 479         u16 ctl, ctl2;
 480
 481         phy->autoneg = 0;
 482         phy->speed = speed;
 483         phy->duplex = fd;
 484         phy->pause = 0;
 485
 486         ctl = phy_read(phy, MII_BMCR);
 487         ctl &= ~(BMCR_FULLDPLX|BMCR_SPEED100|BMCR_SPD2|BMCR_ANENABLE);
 488         ctl |= BMCR_RESET;
 489
 490         /* Select speed & duplex */
 491         switch(speed) {
 492         case SPEED_10:
 493                 break;
 494         case SPEED_100:
 495                 ctl |= BMCR_SPEED100;
 496                 break;
 497         /* I'm not sure about the one below, again, Darwin source is
 498          * quite confusing and I lack chip specs
 499          */
 500         case SPEED_1000:
 501                 ctl |= BMCR_SPD2;
 502         }
 503         if (fd == DUPLEX_FULL)
 504                 ctl |= BMCR_FULLDPLX;
 505
 506         /* Disable crossover. Again, the way Apple does it is strange,
 507          * though I don't assume they are wrong ;)
 508          */
 509         ctl2 = phy_read(phy, MII_M1011_PHY_SPEC_CONTROL);
 510         ctl2 &= ~(MII_M1011_PHY_SPEC_CONTROL_MANUAL_MDIX |
 511                 MII_M1011_PHY_SPEC_CONTROL_AUTO_MDIX |
 512                 MII_1000BASETCONTROL_FULLDUPLEXCAP |
 513                 MII_1000BASETCONTROL_HALFDUPLEXCAP);
 514         if (speed == SPEED_1000)
 515                 ctl2 |= (fd == DUPLEX_FULL) ?
 516                         MII_1000BASETCONTROL_FULLDUPLEXCAP :
 517                         MII_1000BASETCONTROL_HALFDUPLEXCAP;
 518         phy_write(phy, MII_1000BASETCONTROL, ctl2);
 519
 520         // XXX Should we set the sungem to GII now on 1000BT ?
 521
 522         phy_write(phy, MII_BMCR, ctl);
 523
 524         return 0;
 525 }
 526
 527 static int marvell_read_link(struct mii_phy *phy)
 528 {
 529         u16 status;
 530
 531         if (phy->autoneg) {
 532                 status = phy_read(phy, MII_M1011_PHY_SPEC_STATUS);
 533                 if ((status & MII_M1011_PHY_SPEC_STATUS_RESOLVED) == 0)
 534                         return -EAGAIN;
 535                 if (status & MII_M1011_PHY_SPEC_STATUS_1000)
 536                         phy->speed = SPEED_1000;
 537                 else if (status & MII_M1011_PHY_SPEC_STATUS_100)
 538                         phy->speed = SPEED_100;
 539                 else
 540                         phy->speed = SPEED_10;
 541                 if (status & MII_M1011_PHY_SPEC_STATUS_FULLDUPLEX)
 542                         phy->duplex = DUPLEX_FULL;
 543                 else
 544                         phy->duplex = DUPLEX_HALF;
 545                 phy->pause = 0; /* XXX Check against spec ! */
 546         }
 547         /* On non-aneg, we assume what we put in BMCR is the speed,
 548          * though magic-aneg shouldn't prevent this case from occurring
 549          */
 550
 551         return 0;
 552 }
 553
 554 static int genmii_setup_aneg(struct mii_phy *phy, u32 advertise)
 555 {
 556         u16 ctl, adv;
 557
 558         phy->autoneg = 1;
 559         phy->speed = SPEED_10;
 560         phy->duplex = DUPLEX_HALF;
 561         phy->pause = 0;
 562         phy->advertising = advertise;
 563
 564         /* Setup standard advertise */
 565         adv = phy_read(phy, MII_ADVERTISE);
 566         adv &= ~(ADVERTISE_ALL | ADVERTISE_100BASE4);
 567         if (advertise & ADVERTISED_10baseT_Half)
 568                 adv |= ADVERTISE_10HALF;
 569         if (advertise & ADVERTISED_10baseT_Full)
 570                 adv |= ADVERTISE_10FULL;
 571         if (advertise & ADVERTISED_100baseT_Half)
 572                 adv |= ADVERTISE_100HALF;
 573         if (advertise & ADVERTISED_100baseT_Full)
 574                 adv |= ADVERTISE_100FULL;
 575         phy_write(phy, MII_ADVERTISE, adv);
 576
 577         /* Start/Restart aneg */
 578         ctl = phy_read(phy, MII_BMCR);
 579         ctl |= (BMCR_ANENABLE | BMCR_ANRESTART);
 580         phy_write(phy, MII_BMCR, ctl);
 581
 582         return 0;
 583 }
 584
 585 static int genmii_setup_forced(struct mii_phy *phy, int speed, int fd)
 586 {
 587         u16 ctl;
 588
 589         phy->autoneg = 0;
 590         phy->speed = speed;
 591         phy->duplex = fd;
 592         phy->pause = 0;
 593
 594         ctl = phy_read(phy, MII_BMCR);
 595         ctl &= ~(BMCR_FULLDPLX|BMCR_SPEED100|BMCR_ANENABLE);
 596
 597         /* First reset the PHY */
 598         phy_write(phy, MII_BMCR, ctl | BMCR_RESET);
 599
 600         /* Select speed & duplex */
 601         switch(speed) {
 602         case SPEED_10:
 603                 break;
 604         case SPEED_100:
 605                 ctl |= BMCR_SPEED100;
 606                 break;
 607         case SPEED_1000:
 608         default:
 609                 return -EINVAL;
 610         }
 611         if (fd == DUPLEX_FULL)
 612                 ctl |= BMCR_FULLDPLX;
 613         phy_write(phy, MII_BMCR, ctl);
 614
 615         return 0;
 616 }
 617
 618 static int genmii_poll_link(struct mii_phy *phy)
 619 {
 620         u16 status;
 621
 622         (void)phy_read(phy, MII_BMSR);
 623         status = phy_read(phy, MII_BMSR);
 624         if ((status & BMSR_LSTATUS) == 0)
 625                 return 0;
 626         if (phy->autoneg && !(status & BMSR_ANEGCOMPLETE))
 627                 return 0;
 628         return 1;
 629 }
 630
 631 static int genmii_read_link(struct mii_phy *phy)
 632 {
 633         u16 lpa;
 634
 635         if (phy->autoneg) {
 636                 lpa = phy_read(phy, MII_LPA);
 637
 638                 if (lpa & (LPA_10FULL | LPA_100FULL))
 639                         phy->duplex = DUPLEX_FULL;
 640                 else
 641                         phy->duplex = DUPLEX_HALF;
 642                 if (lpa & (LPA_100FULL | LPA_100HALF))
 643                         phy->speed = SPEED_100;
 644                 else
 645                         phy->speed = SPEED_10;
 646                 phy->pause = 0;
 647         }
 648         /* On non-aneg, we assume what we put in BMCR is the speed,
 649          * though magic-aneg shouldn't prevent this case from occurring
 650          */
 651
 652          return 0;
 653 }
 654
 655
 656 #define MII_BASIC_FEATURES      (SUPPORTED_10baseT_Half | SUPPORTED_10baseT_Full | \
 657                                  SUPPORTED_100baseT_Half | SUPPORTED_100baseT_Full | \
 658                                  SUPPORTED_Autoneg | SUPPORTED_TP | SUPPORTED_MII)
 659 #define MII_GBIT_FEATURES       (MII_BASIC_FEATURES | \
 660                                  SUPPORTED_1000baseT_Half | SUPPORTED_1000baseT_Full)
 661
 662 /* Broadcom BCM 5201 */
 663 static struct mii_phy_ops bcm5201_phy_ops = {
 664         .init           = bcm5201_init,
 665         .suspend        = bcm5201_suspend,
 666         .setup_aneg     = genmii_setup_aneg,
 667         .setup_forced   = genmii_setup_forced,
 668         .poll_link      = genmii_poll_link,
 669         .read_link      = genmii_read_link,
 670 };
 671
 672 static struct mii_phy_def bcm5201_phy_def = {
 673         .phy_id         = 0x00406210,
 674         .phy_id_mask    = 0xfffffff0,
 675         .name           = "BCM5201",
 676         .features       = MII_BASIC_FEATURES,
 677         .magic_aneg     = 1,
 678         .ops            = &bcm5201_phy_ops
 679 };
 680
 681 /* Broadcom BCM 5221 */
 682 static struct mii_phy_ops bcm5221_phy_ops = {
 683         .suspend        = bcm5221_suspend,
 684         .init           = bcm5221_init,
 685         .setup_aneg     = genmii_setup_aneg,
 686         .setup_forced   = genmii_setup_forced,
 687         .poll_link      = genmii_poll_link,
 688         .read_link      = genmii_read_link,
 689 };
 690
 691 static struct mii_phy_def bcm5221_phy_def = {
 692         .phy_id         = 0x004061e0,
 693         .phy_id_mask    = 0xfffffff0,
 694         .name           = "BCM5221",
 695         .features       = MII_BASIC_FEATURES,
 696         .magic_aneg     = 1,
 697         .ops            = &bcm5221_phy_ops
 698 };
 699
 700 /* Broadcom BCM 5400 */
 701 static struct mii_phy_ops bcm5400_phy_ops = {
 702         .init           = bcm5400_init,
 703         .suspend        = bcm5400_suspend,
 704         .setup_aneg     = bcm54xx_setup_aneg,
 705         .setup_forced   = bcm54xx_setup_forced,
 706         .poll_link      = genmii_poll_link,
 707         .read_link      = bcm54xx_read_link,
 708 };
 709
 710 static struct mii_phy_def bcm5400_phy_def = {
 711         .phy_id         = 0x00206040,
 712         .phy_id_mask    = 0xfffffff0,
 713         .name           = "BCM5400",
 714         .features       = MII_GBIT_FEATURES,
 715         .magic_aneg     = 1,
 716         .ops            = &bcm5400_phy_ops
 717 };
 718
 719 /* Broadcom BCM 5401 */
 720 static struct mii_phy_ops bcm5401_phy_ops = {
 721         .init           = bcm5401_init,
 722         .suspend        = bcm5401_suspend,
 723         .setup_aneg     = bcm54xx_setup_aneg,
 724         .setup_forced   = bcm54xx_setup_forced,
 725         .poll_link      = genmii_poll_link,
 726         .read_link      = bcm54xx_read_link,
 727 };
 728
 729 static struct mii_phy_def bcm5401_phy_def = {
 730         .phy_id         = 0x00206050,
 731         .phy_id_mask    = 0xfffffff0,
 732         .name           = "BCM5401",
 733         .features       = MII_GBIT_FEATURES,
 734         .magic_aneg     = 1,
 735         .ops            = &bcm5401_phy_ops
 736 };
 737
 738 /* Broadcom BCM 5411 */
 739 static struct mii_phy_ops bcm5411_phy_ops = {
 740         .init           = bcm5411_init,
 741         .suspend        = generic_suspend,
 742         .setup_aneg     = bcm54xx_setup_aneg,
 743         .setup_forced   = bcm54xx_setup_forced,
 744         .poll_link      = genmii_poll_link,
 745         .read_link      = bcm54xx_read_link,
 746 };
 747
 748 static struct mii_phy_def bcm5411_phy_def = {
 749         .phy_id         = 0x00206070,
 750         .phy_id_mask    = 0xfffffff0,
 751         .name           = "BCM5411",
 752         .features       = MII_GBIT_FEATURES,
 753         .magic_aneg     = 1,
 754         .ops            = &bcm5411_phy_ops
 755 };
 756
 757 /* Broadcom BCM 5421 */
 758 static struct mii_phy_ops bcm5421_phy_ops = {
 759         .init           = bcm5421_init,
 760         .suspend        = generic_suspend,
 761         .setup_aneg     = bcm54xx_setup_aneg,
 762         .setup_forced   = bcm54xx_setup_forced,
 763         .poll_link      = genmii_poll_link,
 764         .read_link      = bcm54xx_read_link,
 765 };
 766
 767 static struct mii_phy_def bcm5421_phy_def = {
 768         .phy_id         = 0x002060e0,
 769         .phy_id_mask    = 0xfffffff0,
 770         .name           = "BCM5421",
 771         .features       = MII_GBIT_FEATURES,
 772         .magic_aneg     = 1,
 773         .ops            = &bcm5421_phy_ops
 774 };
 775
 776 /* Broadcom BCM 5421 built-in K2 */
 777 static struct mii_phy_ops bcm5421k2_phy_ops = {
 778         .init           = bcm5421_init,
 779         .suspend        = generic_suspend,
 780         .setup_aneg     = bcm54xx_setup_aneg,
 781         .setup_forced   = bcm54xx_setup_forced,
 782         .poll_link      = genmii_poll_link,
 783         .read_link      = bcm54xx_read_link,
 784 };
 785
 786 static struct mii_phy_def bcm5421k2_phy_def = {
 787         .phy_id         = 0x002062e0,
 788         .phy_id_mask    = 0xfffffff0,
 789         .name           = "BCM5421-K2",
 790         .features       = MII_GBIT_FEATURES,
 791         .magic_aneg     = 1,
 792         .ops            = &bcm5421k2_phy_ops
 793 };
 794
 795 /* Broadcom BCM 5462 built-in Vesta */
 796 static struct mii_phy_ops bcm5462V_phy_ops = {
 797         .init           = bcm5421_init,
 798         .suspend        = generic_suspend,
 799         .setup_aneg     = bcm54xx_setup_aneg,
 800         .setup_forced   = bcm54xx_setup_forced,
 801         .poll_link      = genmii_poll_link,
 802         .read_link      = bcm54xx_read_link,
 803 };
 804
 805 static struct mii_phy_def bcm5462V_phy_def = {
 806         .phy_id         = 0x002060d0,
 807         .phy_id_mask    = 0xfffffff0,
 808         .name           = "BCM5462-Vesta",
 809         .features       = MII_GBIT_FEATURES,
 810         .magic_aneg     = 1,
 811         .ops            = &bcm5462V_phy_ops
 812 };
 813
 814 /* Marvell 88E1101 (Apple seem to deal with 2 different revs,
 815  * I masked out the 8 last bits to get both, but some specs
 816  * would be useful here) --BenH.
 817  */
 818 static struct mii_phy_ops marvell_phy_ops = {
 819         .suspend        = generic_suspend,
 820         .setup_aneg     = marvell_setup_aneg,
 821         .setup_forced   = marvell_setup_forced,
 822         .poll_link      = genmii_poll_link,
 823         .read_link      = marvell_read_link
 824 };
 825
 826 static struct mii_phy_def marvell_phy_def = {
 827         .phy_id         = 0x01410c00,
 828         .phy_id_mask    = 0xffffff00,
 829         .name           = "Marvell 88E1101",
 830         .features       = MII_GBIT_FEATURES,
 831         .magic_aneg     = 1,
 832         .ops            = &marvell_phy_ops
 833 };
 834
 835 /* Generic implementation for most 10/100 PHYs */
 836 static struct mii_phy_ops generic_phy_ops = {
 837         .setup_aneg     = genmii_setup_aneg,
 838         .setup_forced   = genmii_setup_forced,
 839         .poll_link      = genmii_poll_link,
 840         .read_link      = genmii_read_link
 841 };
 842
 843 static struct mii_phy_def genmii_phy_def = {
 844         .phy_id         = 0x00000000,
 845         .phy_id_mask    = 0x00000000,
 846         .name           = "Generic MII",
 847         .features       = MII_BASIC_FEATURES,
 848         .magic_aneg     = 0,
 849         .ops            = &generic_phy_ops
 850 };
 851
 852 static struct mii_phy_def* mii_phy_table[] = {
 853         &bcm5201_phy_def,
 854         &bcm5221_phy_def,
 855         &bcm5400_phy_def,
 856         &bcm5401_phy_def,
 857         &bcm5411_phy_def,
 858         &bcm5421_phy_def,
 859         &bcm5421k2_phy_def,
 860         &bcm5462V_phy_def,
 861         &marvell_phy_def,
 862         &genmii_phy_def,
 863         NULL
 864 };
 865
 866 int mii_phy_probe(struct mii_phy *phy, int mii_id)
 867 {
 868         int rc;
 869         u32 id;
 870         struct mii_phy_def* def;
 871         int i;
 872
 873         /* We do not reset the mii_phy structure as the driver
 874          * may re-probe the PHY regulary
 875          */
 876         phy->mii_id = mii_id;
 877
 878         /* Take PHY out of isloate mode and reset it. */
 879         rc = reset_one_mii_phy(phy, mii_id);
 880         if (rc)
 881                 goto fail;
 882
 883         /* Read ID and find matching entry */
 884         id = (phy_read(phy, MII_PHYSID1) << 16 | phy_read(phy, MII_PHYSID2));
 885         printk(KERN_DEBUG "PHY ID: %x, addr: %x\n", id, mii_id);
 886         for (i=0; (def = mii_phy_table[i]) != NULL; i++)
 887                 if ((id & def->phy_id_mask) == def->phy_id)
 888                         break;
 889         /* Should never be NULL (we have a generic entry), but... */
 890         if (def == NULL)
 891                 goto fail;
 892
 893         phy->def = def;
 894
 895         return 0;
 896 fail:
 897         phy->speed = 0;
 898         phy->duplex = 0;
 899         phy->pause = 0;
 900         phy->advertising = 0;
 901         return -ENODEV;
 902 }
 903
 904 EXPORT_SYMBOL(mii_phy_probe);
 905 MODULE_LICENSE("GPL");
 906