mmc: core: add eMMC hardware reset support
[pandora-kernel.git] / drivers / mmc / host / sdhci.c
1 /*
2  *  linux/drivers/mmc/host/sdhci.c - Secure Digital Host Controller Interface driver
3  *
4  *  Copyright (C) 2005-2008 Pierre Ossman, All Rights Reserved.
5  *
6  * This program is free software; you can redistribute it and/or modify
7  * it under the terms of the GNU General Public License as published by
8  * the Free Software Foundation; either version 2 of the License, or (at
9  * your option) any later version.
10  *
11  * Thanks to the following companies for their support:
12  *
13  *     - JMicron (hardware and technical support)
14  */
15
16 #include <linux/delay.h>
17 #include <linux/highmem.h>
18 #include <linux/io.h>
19 #include <linux/dma-mapping.h>
20 #include <linux/slab.h>
21 #include <linux/scatterlist.h>
22 #include <linux/regulator/consumer.h>
23
24 #include <linux/leds.h>
25
26 #include <linux/mmc/mmc.h>
27 #include <linux/mmc/host.h>
28
29 #include "sdhci.h"
30
31 #define DRIVER_NAME "sdhci"
32
33 #define DBG(f, x...) \
34         pr_debug(DRIVER_NAME " [%s()]: " f, __func__,## x)
35
36 #if defined(CONFIG_LEDS_CLASS) || (defined(CONFIG_LEDS_CLASS_MODULE) && \
37         defined(CONFIG_MMC_SDHCI_MODULE))
38 #define SDHCI_USE_LEDS_CLASS
39 #endif
40
41 #define MAX_TUNING_LOOP 40
42
43 static unsigned int debug_quirks = 0;
44
45 static void sdhci_finish_data(struct sdhci_host *);
46
47 static void sdhci_send_command(struct sdhci_host *, struct mmc_command *);
48 static void sdhci_finish_command(struct sdhci_host *);
49 static int sdhci_execute_tuning(struct mmc_host *mmc);
50 static void sdhci_tuning_timer(unsigned long data);
51
52 static void sdhci_dumpregs(struct sdhci_host *host)
53 {
54         printk(KERN_DEBUG DRIVER_NAME ": =========== REGISTER DUMP (%s)===========\n",
55                 mmc_hostname(host->mmc));
56
57         printk(KERN_DEBUG DRIVER_NAME ": Sys addr: 0x%08x | Version:  0x%08x\n",
58                 sdhci_readl(host, SDHCI_DMA_ADDRESS),
59                 sdhci_readw(host, SDHCI_HOST_VERSION));
60         printk(KERN_DEBUG DRIVER_NAME ": Blk size: 0x%08x | Blk cnt:  0x%08x\n",
61                 sdhci_readw(host, SDHCI_BLOCK_SIZE),
62                 sdhci_readw(host, SDHCI_BLOCK_COUNT));
63         printk(KERN_DEBUG DRIVER_NAME ": Argument: 0x%08x | Trn mode: 0x%08x\n",
64                 sdhci_readl(host, SDHCI_ARGUMENT),
65                 sdhci_readw(host, SDHCI_TRANSFER_MODE));
66         printk(KERN_DEBUG DRIVER_NAME ": Present:  0x%08x | Host ctl: 0x%08x\n",
67                 sdhci_readl(host, SDHCI_PRESENT_STATE),
68                 sdhci_readb(host, SDHCI_HOST_CONTROL));
69         printk(KERN_DEBUG DRIVER_NAME ": Power:    0x%08x | Blk gap:  0x%08x\n",
70                 sdhci_readb(host, SDHCI_POWER_CONTROL),
71                 sdhci_readb(host, SDHCI_BLOCK_GAP_CONTROL));
72         printk(KERN_DEBUG DRIVER_NAME ": Wake-up:  0x%08x | Clock:    0x%08x\n",
73                 sdhci_readb(host, SDHCI_WAKE_UP_CONTROL),
74                 sdhci_readw(host, SDHCI_CLOCK_CONTROL));
75         printk(KERN_DEBUG DRIVER_NAME ": Timeout:  0x%08x | Int stat: 0x%08x\n",
76                 sdhci_readb(host, SDHCI_TIMEOUT_CONTROL),
77                 sdhci_readl(host, SDHCI_INT_STATUS));
78         printk(KERN_DEBUG DRIVER_NAME ": Int enab: 0x%08x | Sig enab: 0x%08x\n",
79                 sdhci_readl(host, SDHCI_INT_ENABLE),
80                 sdhci_readl(host, SDHCI_SIGNAL_ENABLE));
81         printk(KERN_DEBUG DRIVER_NAME ": AC12 err: 0x%08x | Slot int: 0x%08x\n",
82                 sdhci_readw(host, SDHCI_ACMD12_ERR),
83                 sdhci_readw(host, SDHCI_SLOT_INT_STATUS));
84         printk(KERN_DEBUG DRIVER_NAME ": Caps:     0x%08x | Caps_1:   0x%08x\n",
85                 sdhci_readl(host, SDHCI_CAPABILITIES),
86                 sdhci_readl(host, SDHCI_CAPABILITIES_1));
87         printk(KERN_DEBUG DRIVER_NAME ": Cmd:      0x%08x | Max curr: 0x%08x\n",
88                 sdhci_readw(host, SDHCI_COMMAND),
89                 sdhci_readl(host, SDHCI_MAX_CURRENT));
90         printk(KERN_DEBUG DRIVER_NAME ": Host ctl2: 0x%08x\n",
91                 sdhci_readw(host, SDHCI_HOST_CONTROL2));
92
93         if (host->flags & SDHCI_USE_ADMA)
94                 printk(KERN_DEBUG DRIVER_NAME ": ADMA Err: 0x%08x | ADMA Ptr: 0x%08x\n",
95                        readl(host->ioaddr + SDHCI_ADMA_ERROR),
96                        readl(host->ioaddr + SDHCI_ADMA_ADDRESS));
97
98         printk(KERN_DEBUG DRIVER_NAME ": ===========================================\n");
99 }
100
101 /*****************************************************************************\
102  *                                                                           *
103  * Low level functions                                                       *
104  *                                                                           *
105 \*****************************************************************************/
106
107 static void sdhci_clear_set_irqs(struct sdhci_host *host, u32 clear, u32 set)
108 {
109         u32 ier;
110
111         ier = sdhci_readl(host, SDHCI_INT_ENABLE);
112         ier &= ~clear;
113         ier |= set;
114         sdhci_writel(host, ier, SDHCI_INT_ENABLE);
115         sdhci_writel(host, ier, SDHCI_SIGNAL_ENABLE);
116 }
117
118 static void sdhci_unmask_irqs(struct sdhci_host *host, u32 irqs)
119 {
120         sdhci_clear_set_irqs(host, 0, irqs);
121 }
122
123 static void sdhci_mask_irqs(struct sdhci_host *host, u32 irqs)
124 {
125         sdhci_clear_set_irqs(host, irqs, 0);
126 }
127
128 static void sdhci_set_card_detection(struct sdhci_host *host, bool enable)
129 {
130         u32 present, irqs;
131
132         if (host->quirks & SDHCI_QUIRK_BROKEN_CARD_DETECTION)
133                 return;
134
135         present = sdhci_readl(host, SDHCI_PRESENT_STATE) &
136                               SDHCI_CARD_PRESENT;
137         irqs = present ? SDHCI_INT_CARD_REMOVE : SDHCI_INT_CARD_INSERT;
138
139         if (enable)
140                 sdhci_unmask_irqs(host, irqs);
141         else
142                 sdhci_mask_irqs(host, irqs);
143 }
144
145 static void sdhci_enable_card_detection(struct sdhci_host *host)
146 {
147         sdhci_set_card_detection(host, true);
148 }
149
150 static void sdhci_disable_card_detection(struct sdhci_host *host)
151 {
152         sdhci_set_card_detection(host, false);
153 }
154
155 static void sdhci_reset(struct sdhci_host *host, u8 mask)
156 {
157         unsigned long timeout;
158         u32 uninitialized_var(ier);
159
160         if (host->quirks & SDHCI_QUIRK_NO_CARD_NO_RESET) {
161                 if (!(sdhci_readl(host, SDHCI_PRESENT_STATE) &
162                         SDHCI_CARD_PRESENT))
163                         return;
164         }
165
166         if (host->quirks & SDHCI_QUIRK_RESTORE_IRQS_AFTER_RESET)
167                 ier = sdhci_readl(host, SDHCI_INT_ENABLE);
168
169         if (host->ops->platform_reset_enter)
170                 host->ops->platform_reset_enter(host, mask);
171
172         sdhci_writeb(host, mask, SDHCI_SOFTWARE_RESET);
173
174         if (mask & SDHCI_RESET_ALL)
175                 host->clock = 0;
176
177         /* Wait max 100 ms */
178         timeout = 100;
179
180         /* hw clears the bit when it's done */
181         while (sdhci_readb(host, SDHCI_SOFTWARE_RESET) & mask) {
182                 if (timeout == 0) {
183                         printk(KERN_ERR "%s: Reset 0x%x never completed.\n",
184                                 mmc_hostname(host->mmc), (int)mask);
185                         sdhci_dumpregs(host);
186                         return;
187                 }
188                 timeout--;
189                 mdelay(1);
190         }
191
192         if (host->ops->platform_reset_exit)
193                 host->ops->platform_reset_exit(host, mask);
194
195         if (host->quirks & SDHCI_QUIRK_RESTORE_IRQS_AFTER_RESET)
196                 sdhci_clear_set_irqs(host, SDHCI_INT_ALL_MASK, ier);
197 }
198
199 static void sdhci_set_ios(struct mmc_host *mmc, struct mmc_ios *ios);
200
201 static void sdhci_init(struct sdhci_host *host, int soft)
202 {
203         if (soft)
204                 sdhci_reset(host, SDHCI_RESET_CMD|SDHCI_RESET_DATA);
205         else
206                 sdhci_reset(host, SDHCI_RESET_ALL);
207
208         sdhci_clear_set_irqs(host, SDHCI_INT_ALL_MASK,
209                 SDHCI_INT_BUS_POWER | SDHCI_INT_DATA_END_BIT |
210                 SDHCI_INT_DATA_CRC | SDHCI_INT_DATA_TIMEOUT | SDHCI_INT_INDEX |
211                 SDHCI_INT_END_BIT | SDHCI_INT_CRC | SDHCI_INT_TIMEOUT |
212                 SDHCI_INT_DATA_END | SDHCI_INT_RESPONSE);
213
214         if (soft) {
215                 /* force clock reconfiguration */
216                 host->clock = 0;
217                 sdhci_set_ios(host->mmc, &host->mmc->ios);
218         }
219 }
220
221 static void sdhci_reinit(struct sdhci_host *host)
222 {
223         sdhci_init(host, 0);
224         sdhci_enable_card_detection(host);
225 }
226
227 static void sdhci_activate_led(struct sdhci_host *host)
228 {
229         u8 ctrl;
230
231         ctrl = sdhci_readb(host, SDHCI_HOST_CONTROL);
232         ctrl |= SDHCI_CTRL_LED;
233         sdhci_writeb(host, ctrl, SDHCI_HOST_CONTROL);
234 }
235
236 static void sdhci_deactivate_led(struct sdhci_host *host)
237 {
238         u8 ctrl;
239
240         ctrl = sdhci_readb(host, SDHCI_HOST_CONTROL);
241         ctrl &= ~SDHCI_CTRL_LED;
242         sdhci_writeb(host, ctrl, SDHCI_HOST_CONTROL);
243 }
244
245 #ifdef SDHCI_USE_LEDS_CLASS
246 static void sdhci_led_control(struct led_classdev *led,
247         enum led_brightness brightness)
248 {
249         struct sdhci_host *host = container_of(led, struct sdhci_host, led);
250         unsigned long flags;
251
252         spin_lock_irqsave(&host->lock, flags);
253
254         if (brightness == LED_OFF)
255                 sdhci_deactivate_led(host);
256         else
257                 sdhci_activate_led(host);
258
259         spin_unlock_irqrestore(&host->lock, flags);
260 }
261 #endif
262
263 /*****************************************************************************\
264  *                                                                           *
265  * Core functions                                                            *
266  *                                                                           *
267 \*****************************************************************************/
268
269 static void sdhci_read_block_pio(struct sdhci_host *host)
270 {
271         unsigned long flags;
272         size_t blksize, len, chunk;
273         u32 uninitialized_var(scratch);
274         u8 *buf;
275
276         DBG("PIO reading\n");
277
278         blksize = host->data->blksz;
279         chunk = 0;
280
281         local_irq_save(flags);
282
283         while (blksize) {
284                 if (!sg_miter_next(&host->sg_miter))
285                         BUG();
286
287                 len = min(host->sg_miter.length, blksize);
288
289                 blksize -= len;
290                 host->sg_miter.consumed = len;
291
292                 buf = host->sg_miter.addr;
293
294                 while (len) {
295                         if (chunk == 0) {
296                                 scratch = sdhci_readl(host, SDHCI_BUFFER);
297                                 chunk = 4;
298                         }
299
300                         *buf = scratch & 0xFF;
301
302                         buf++;
303                         scratch >>= 8;
304                         chunk--;
305                         len--;
306                 }
307         }
308
309         sg_miter_stop(&host->sg_miter);
310
311         local_irq_restore(flags);
312 }
313
314 static void sdhci_write_block_pio(struct sdhci_host *host)
315 {
316         unsigned long flags;
317         size_t blksize, len, chunk;
318         u32 scratch;
319         u8 *buf;
320
321         DBG("PIO writing\n");
322
323         blksize = host->data->blksz;
324         chunk = 0;
325         scratch = 0;
326
327         local_irq_save(flags);
328
329         while (blksize) {
330                 if (!sg_miter_next(&host->sg_miter))
331                         BUG();
332
333                 len = min(host->sg_miter.length, blksize);
334
335                 blksize -= len;
336                 host->sg_miter.consumed = len;
337
338                 buf = host->sg_miter.addr;
339
340                 while (len) {
341                         scratch |= (u32)*buf << (chunk * 8);
342
343                         buf++;
344                         chunk++;
345                         len--;
346
347                         if ((chunk == 4) || ((len == 0) && (blksize == 0))) {
348                                 sdhci_writel(host, scratch, SDHCI_BUFFER);
349                                 chunk = 0;
350                                 scratch = 0;
351                         }
352                 }
353         }
354
355         sg_miter_stop(&host->sg_miter);
356
357         local_irq_restore(flags);
358 }
359
360 static void sdhci_transfer_pio(struct sdhci_host *host)
361 {
362         u32 mask;
363
364         BUG_ON(!host->data);
365
366         if (host->blocks == 0)
367                 return;
368
369         if (host->data->flags & MMC_DATA_READ)
370                 mask = SDHCI_DATA_AVAILABLE;
371         else
372                 mask = SDHCI_SPACE_AVAILABLE;
373
374         /*
375          * Some controllers (JMicron JMB38x) mess up the buffer bits
376          * for transfers < 4 bytes. As long as it is just one block,
377          * we can ignore the bits.
378          */
379         if ((host->quirks & SDHCI_QUIRK_BROKEN_SMALL_PIO) &&
380                 (host->data->blocks == 1))
381                 mask = ~0;
382
383         while (sdhci_readl(host, SDHCI_PRESENT_STATE) & mask) {
384                 if (host->quirks & SDHCI_QUIRK_PIO_NEEDS_DELAY)
385                         udelay(100);
386
387                 if (host->data->flags & MMC_DATA_READ)
388                         sdhci_read_block_pio(host);
389                 else
390                         sdhci_write_block_pio(host);
391
392                 host->blocks--;
393                 if (host->blocks == 0)
394                         break;
395         }
396
397         DBG("PIO transfer complete.\n");
398 }
399
400 static char *sdhci_kmap_atomic(struct scatterlist *sg, unsigned long *flags)
401 {
402         local_irq_save(*flags);
403         return kmap_atomic(sg_page(sg), KM_BIO_SRC_IRQ) + sg->offset;
404 }
405
406 static void sdhci_kunmap_atomic(void *buffer, unsigned long *flags)
407 {
408         kunmap_atomic(buffer, KM_BIO_SRC_IRQ);
409         local_irq_restore(*flags);
410 }
411
412 static void sdhci_set_adma_desc(u8 *desc, u32 addr, int len, unsigned cmd)
413 {
414         __le32 *dataddr = (__le32 __force *)(desc + 4);
415         __le16 *cmdlen = (__le16 __force *)desc;
416
417         /* SDHCI specification says ADMA descriptors should be 4 byte
418          * aligned, so using 16 or 32bit operations should be safe. */
419
420         cmdlen[0] = cpu_to_le16(cmd);
421         cmdlen[1] = cpu_to_le16(len);
422
423         dataddr[0] = cpu_to_le32(addr);
424 }
425
426 static int sdhci_adma_table_pre(struct sdhci_host *host,
427         struct mmc_data *data)
428 {
429         int direction;
430
431         u8 *desc;
432         u8 *align;
433         dma_addr_t addr;
434         dma_addr_t align_addr;
435         int len, offset;
436
437         struct scatterlist *sg;
438         int i;
439         char *buffer;
440         unsigned long flags;
441
442         /*
443          * The spec does not specify endianness of descriptor table.
444          * We currently guess that it is LE.
445          */
446
447         if (data->flags & MMC_DATA_READ)
448                 direction = DMA_FROM_DEVICE;
449         else
450                 direction = DMA_TO_DEVICE;
451
452         /*
453          * The ADMA descriptor table is mapped further down as we
454          * need to fill it with data first.
455          */
456
457         host->align_addr = dma_map_single(mmc_dev(host->mmc),
458                 host->align_buffer, 128 * 4, direction);
459         if (dma_mapping_error(mmc_dev(host->mmc), host->align_addr))
460                 goto fail;
461         BUG_ON(host->align_addr & 0x3);
462
463         host->sg_count = dma_map_sg(mmc_dev(host->mmc),
464                 data->sg, data->sg_len, direction);
465         if (host->sg_count == 0)
466                 goto unmap_align;
467
468         desc = host->adma_desc;
469         align = host->align_buffer;
470
471         align_addr = host->align_addr;
472
473         for_each_sg(data->sg, sg, host->sg_count, i) {
474                 addr = sg_dma_address(sg);
475                 len = sg_dma_len(sg);
476
477                 /*
478                  * The SDHCI specification states that ADMA
479                  * addresses must be 32-bit aligned. If they
480                  * aren't, then we use a bounce buffer for
481                  * the (up to three) bytes that screw up the
482                  * alignment.
483                  */
484                 offset = (4 - (addr & 0x3)) & 0x3;
485                 if (offset) {
486                         if (data->flags & MMC_DATA_WRITE) {
487                                 buffer = sdhci_kmap_atomic(sg, &flags);
488                                 WARN_ON(((long)buffer & PAGE_MASK) > (PAGE_SIZE - 3));
489                                 memcpy(align, buffer, offset);
490                                 sdhci_kunmap_atomic(buffer, &flags);
491                         }
492
493                         /* tran, valid */
494                         sdhci_set_adma_desc(desc, align_addr, offset, 0x21);
495
496                         BUG_ON(offset > 65536);
497
498                         align += 4;
499                         align_addr += 4;
500
501                         desc += 8;
502
503                         addr += offset;
504                         len -= offset;
505                 }
506
507                 BUG_ON(len > 65536);
508
509                 /* tran, valid */
510                 sdhci_set_adma_desc(desc, addr, len, 0x21);
511                 desc += 8;
512
513                 /*
514                  * If this triggers then we have a calculation bug
515                  * somewhere. :/
516                  */
517                 WARN_ON((desc - host->adma_desc) > (128 * 2 + 1) * 4);
518         }
519
520         if (host->quirks & SDHCI_QUIRK_NO_ENDATTR_IN_NOPDESC) {
521                 /*
522                 * Mark the last descriptor as the terminating descriptor
523                 */
524                 if (desc != host->adma_desc) {
525                         desc -= 8;
526                         desc[0] |= 0x2; /* end */
527                 }
528         } else {
529                 /*
530                 * Add a terminating entry.
531                 */
532
533                 /* nop, end, valid */
534                 sdhci_set_adma_desc(desc, 0, 0, 0x3);
535         }
536
537         /*
538          * Resync align buffer as we might have changed it.
539          */
540         if (data->flags & MMC_DATA_WRITE) {
541                 dma_sync_single_for_device(mmc_dev(host->mmc),
542                         host->align_addr, 128 * 4, direction);
543         }
544
545         host->adma_addr = dma_map_single(mmc_dev(host->mmc),
546                 host->adma_desc, (128 * 2 + 1) * 4, DMA_TO_DEVICE);
547         if (dma_mapping_error(mmc_dev(host->mmc), host->adma_addr))
548                 goto unmap_entries;
549         BUG_ON(host->adma_addr & 0x3);
550
551         return 0;
552
553 unmap_entries:
554         dma_unmap_sg(mmc_dev(host->mmc), data->sg,
555                 data->sg_len, direction);
556 unmap_align:
557         dma_unmap_single(mmc_dev(host->mmc), host->align_addr,
558                 128 * 4, direction);
559 fail:
560         return -EINVAL;
561 }
562
563 static void sdhci_adma_table_post(struct sdhci_host *host,
564         struct mmc_data *data)
565 {
566         int direction;
567
568         struct scatterlist *sg;
569         int i, size;
570         u8 *align;
571         char *buffer;
572         unsigned long flags;
573
574         if (data->flags & MMC_DATA_READ)
575                 direction = DMA_FROM_DEVICE;
576         else
577                 direction = DMA_TO_DEVICE;
578
579         dma_unmap_single(mmc_dev(host->mmc), host->adma_addr,
580                 (128 * 2 + 1) * 4, DMA_TO_DEVICE);
581
582         dma_unmap_single(mmc_dev(host->mmc), host->align_addr,
583                 128 * 4, direction);
584
585         if (data->flags & MMC_DATA_READ) {
586                 dma_sync_sg_for_cpu(mmc_dev(host->mmc), data->sg,
587                         data->sg_len, direction);
588
589                 align = host->align_buffer;
590
591                 for_each_sg(data->sg, sg, host->sg_count, i) {
592                         if (sg_dma_address(sg) & 0x3) {
593                                 size = 4 - (sg_dma_address(sg) & 0x3);
594
595                                 buffer = sdhci_kmap_atomic(sg, &flags);
596                                 WARN_ON(((long)buffer & PAGE_MASK) > (PAGE_SIZE - 3));
597                                 memcpy(buffer, align, size);
598                                 sdhci_kunmap_atomic(buffer, &flags);
599
600                                 align += 4;
601                         }
602                 }
603         }
604
605         dma_unmap_sg(mmc_dev(host->mmc), data->sg,
606                 data->sg_len, direction);
607 }
608
609 static u8 sdhci_calc_timeout(struct sdhci_host *host, struct mmc_command *cmd)
610 {
611         u8 count;
612         struct mmc_data *data = cmd->data;
613         unsigned target_timeout, current_timeout;
614
615         /*
616          * If the host controller provides us with an incorrect timeout
617          * value, just skip the check and use 0xE.  The hardware may take
618          * longer to time out, but that's much better than having a too-short
619          * timeout value.
620          */
621         if (host->quirks & SDHCI_QUIRK_BROKEN_TIMEOUT_VAL)
622                 return 0xE;
623
624         /* Unspecified timeout, assume max */
625         if (!data && !cmd->cmd_timeout_ms)
626                 return 0xE;
627
628         /* timeout in us */
629         if (!data)
630                 target_timeout = cmd->cmd_timeout_ms * 1000;
631         else {
632                 target_timeout = data->timeout_ns / 1000;
633                 if (host->clock)
634                         target_timeout += data->timeout_clks / host->clock;
635         }
636
637         /*
638          * Figure out needed cycles.
639          * We do this in steps in order to fit inside a 32 bit int.
640          * The first step is the minimum timeout, which will have a
641          * minimum resolution of 6 bits:
642          * (1) 2^13*1000 > 2^22,
643          * (2) host->timeout_clk < 2^16
644          *     =>
645          *     (1) / (2) > 2^6
646          */
647         count = 0;
648         current_timeout = (1 << 13) * 1000 / host->timeout_clk;
649         while (current_timeout < target_timeout) {
650                 count++;
651                 current_timeout <<= 1;
652                 if (count >= 0xF)
653                         break;
654         }
655
656         if (count >= 0xF) {
657                 printk(KERN_WARNING "%s: Too large timeout requested for CMD%d!\n",
658                        mmc_hostname(host->mmc), cmd->opcode);
659                 count = 0xE;
660         }
661
662         return count;
663 }
664
665 static void sdhci_set_transfer_irqs(struct sdhci_host *host)
666 {
667         u32 pio_irqs = SDHCI_INT_DATA_AVAIL | SDHCI_INT_SPACE_AVAIL;
668         u32 dma_irqs = SDHCI_INT_DMA_END | SDHCI_INT_ADMA_ERROR;
669
670         if (host->flags & SDHCI_REQ_USE_DMA)
671                 sdhci_clear_set_irqs(host, pio_irqs, dma_irqs);
672         else
673                 sdhci_clear_set_irqs(host, dma_irqs, pio_irqs);
674 }
675
676 static void sdhci_prepare_data(struct sdhci_host *host, struct mmc_command *cmd)
677 {
678         u8 count;
679         u8 ctrl;
680         struct mmc_data *data = cmd->data;
681         int ret;
682
683         WARN_ON(host->data);
684
685         if (data || (cmd->flags & MMC_RSP_BUSY)) {
686                 count = sdhci_calc_timeout(host, cmd);
687                 sdhci_writeb(host, count, SDHCI_TIMEOUT_CONTROL);
688         }
689
690         if (!data)
691                 return;
692
693         /* Sanity checks */
694         BUG_ON(data->blksz * data->blocks > 524288);
695         BUG_ON(data->blksz > host->mmc->max_blk_size);
696         BUG_ON(data->blocks > 65535);
697
698         host->data = data;
699         host->data_early = 0;
700         host->data->bytes_xfered = 0;
701
702         if (host->flags & (SDHCI_USE_SDMA | SDHCI_USE_ADMA))
703                 host->flags |= SDHCI_REQ_USE_DMA;
704
705         /*
706          * FIXME: This doesn't account for merging when mapping the
707          * scatterlist.
708          */
709         if (host->flags & SDHCI_REQ_USE_DMA) {
710                 int broken, i;
711                 struct scatterlist *sg;
712
713                 broken = 0;
714                 if (host->flags & SDHCI_USE_ADMA) {
715                         if (host->quirks & SDHCI_QUIRK_32BIT_ADMA_SIZE)
716                                 broken = 1;
717                 } else {
718                         if (host->quirks & SDHCI_QUIRK_32BIT_DMA_SIZE)
719                                 broken = 1;
720                 }
721
722                 if (unlikely(broken)) {
723                         for_each_sg(data->sg, sg, data->sg_len, i) {
724                                 if (sg->length & 0x3) {
725                                         DBG("Reverting to PIO because of "
726                                                 "transfer size (%d)\n",
727                                                 sg->length);
728                                         host->flags &= ~SDHCI_REQ_USE_DMA;
729                                         break;
730                                 }
731                         }
732                 }
733         }
734
735         /*
736          * The assumption here being that alignment is the same after
737          * translation to device address space.
738          */
739         if (host->flags & SDHCI_REQ_USE_DMA) {
740                 int broken, i;
741                 struct scatterlist *sg;
742
743                 broken = 0;
744                 if (host->flags & SDHCI_USE_ADMA) {
745                         /*
746                          * As we use 3 byte chunks to work around
747                          * alignment problems, we need to check this
748                          * quirk.
749                          */
750                         if (host->quirks & SDHCI_QUIRK_32BIT_ADMA_SIZE)
751                                 broken = 1;
752                 } else {
753                         if (host->quirks & SDHCI_QUIRK_32BIT_DMA_ADDR)
754                                 broken = 1;
755                 }
756
757                 if (unlikely(broken)) {
758                         for_each_sg(data->sg, sg, data->sg_len, i) {
759                                 if (sg->offset & 0x3) {
760                                         DBG("Reverting to PIO because of "
761                                                 "bad alignment\n");
762                                         host->flags &= ~SDHCI_REQ_USE_DMA;
763                                         break;
764                                 }
765                         }
766                 }
767         }
768
769         if (host->flags & SDHCI_REQ_USE_DMA) {
770                 if (host->flags & SDHCI_USE_ADMA) {
771                         ret = sdhci_adma_table_pre(host, data);
772                         if (ret) {
773                                 /*
774                                  * This only happens when someone fed
775                                  * us an invalid request.
776                                  */
777                                 WARN_ON(1);
778                                 host->flags &= ~SDHCI_REQ_USE_DMA;
779                         } else {
780                                 sdhci_writel(host, host->adma_addr,
781                                         SDHCI_ADMA_ADDRESS);
782                         }
783                 } else {
784                         int sg_cnt;
785
786                         sg_cnt = dma_map_sg(mmc_dev(host->mmc),
787                                         data->sg, data->sg_len,
788                                         (data->flags & MMC_DATA_READ) ?
789                                                 DMA_FROM_DEVICE :
790                                                 DMA_TO_DEVICE);
791                         if (sg_cnt == 0) {
792                                 /*
793                                  * This only happens when someone fed
794                                  * us an invalid request.
795                                  */
796                                 WARN_ON(1);
797                                 host->flags &= ~SDHCI_REQ_USE_DMA;
798                         } else {
799                                 WARN_ON(sg_cnt != 1);
800                                 sdhci_writel(host, sg_dma_address(data->sg),
801                                         SDHCI_DMA_ADDRESS);
802                         }
803                 }
804         }
805
806         /*
807          * Always adjust the DMA selection as some controllers
808          * (e.g. JMicron) can't do PIO properly when the selection
809          * is ADMA.
810          */
811         if (host->version >= SDHCI_SPEC_200) {
812                 ctrl = sdhci_readb(host, SDHCI_HOST_CONTROL);
813                 ctrl &= ~SDHCI_CTRL_DMA_MASK;
814                 if ((host->flags & SDHCI_REQ_USE_DMA) &&
815                         (host->flags & SDHCI_USE_ADMA))
816                         ctrl |= SDHCI_CTRL_ADMA32;
817                 else
818                         ctrl |= SDHCI_CTRL_SDMA;
819                 sdhci_writeb(host, ctrl, SDHCI_HOST_CONTROL);
820         }
821
822         if (!(host->flags & SDHCI_REQ_USE_DMA)) {
823                 int flags;
824
825                 flags = SG_MITER_ATOMIC;
826                 if (host->data->flags & MMC_DATA_READ)
827                         flags |= SG_MITER_TO_SG;
828                 else
829                         flags |= SG_MITER_FROM_SG;
830                 sg_miter_start(&host->sg_miter, data->sg, data->sg_len, flags);
831                 host->blocks = data->blocks;
832         }
833
834         sdhci_set_transfer_irqs(host);
835
836         /* Set the DMA boundary value and block size */
837         sdhci_writew(host, SDHCI_MAKE_BLKSZ(SDHCI_DEFAULT_BOUNDARY_ARG,
838                 data->blksz), SDHCI_BLOCK_SIZE);
839         sdhci_writew(host, data->blocks, SDHCI_BLOCK_COUNT);
840 }
841
842 static void sdhci_set_transfer_mode(struct sdhci_host *host,
843         struct mmc_command *cmd)
844 {
845         u16 mode;
846         struct mmc_data *data = cmd->data;
847
848         if (data == NULL)
849                 return;
850
851         WARN_ON(!host->data);
852
853         mode = SDHCI_TRNS_BLK_CNT_EN;
854         if (mmc_op_multi(cmd->opcode) || data->blocks > 1) {
855                 mode |= SDHCI_TRNS_MULTI;
856                 /*
857                  * If we are sending CMD23, CMD12 never gets sent
858                  * on successful completion (so no Auto-CMD12).
859                  */
860                 if (!host->mrq->sbc && (host->flags & SDHCI_AUTO_CMD12))
861                         mode |= SDHCI_TRNS_AUTO_CMD12;
862                 else if (host->mrq->sbc && (host->flags & SDHCI_AUTO_CMD23)) {
863                         mode |= SDHCI_TRNS_AUTO_CMD23;
864                         sdhci_writel(host, host->mrq->sbc->arg, SDHCI_ARGUMENT2);
865                 }
866         }
867
868         if (data->flags & MMC_DATA_READ)
869                 mode |= SDHCI_TRNS_READ;
870         if (host->flags & SDHCI_REQ_USE_DMA)
871                 mode |= SDHCI_TRNS_DMA;
872
873         sdhci_writew(host, mode, SDHCI_TRANSFER_MODE);
874 }
875
876 static void sdhci_finish_data(struct sdhci_host *host)
877 {
878         struct mmc_data *data;
879
880         BUG_ON(!host->data);
881
882         data = host->data;
883         host->data = NULL;
884
885         if (host->flags & SDHCI_REQ_USE_DMA) {
886                 if (host->flags & SDHCI_USE_ADMA)
887                         sdhci_adma_table_post(host, data);
888                 else {
889                         dma_unmap_sg(mmc_dev(host->mmc), data->sg,
890                                 data->sg_len, (data->flags & MMC_DATA_READ) ?
891                                         DMA_FROM_DEVICE : DMA_TO_DEVICE);
892                 }
893         }
894
895         /*
896          * The specification states that the block count register must
897          * be updated, but it does not specify at what point in the
898          * data flow. That makes the register entirely useless to read
899          * back so we have to assume that nothing made it to the card
900          * in the event of an error.
901          */
902         if (data->error)
903                 data->bytes_xfered = 0;
904         else
905                 data->bytes_xfered = data->blksz * data->blocks;
906
907         /*
908          * Need to send CMD12 if -
909          * a) open-ended multiblock transfer (no CMD23)
910          * b) error in multiblock transfer
911          */
912         if (data->stop &&
913             (data->error ||
914              !host->mrq->sbc)) {
915
916                 /*
917                  * The controller needs a reset of internal state machines
918                  * upon error conditions.
919                  */
920                 if (data->error) {
921                         sdhci_reset(host, SDHCI_RESET_CMD);
922                         sdhci_reset(host, SDHCI_RESET_DATA);
923                 }
924
925                 sdhci_send_command(host, data->stop);
926         } else
927                 tasklet_schedule(&host->finish_tasklet);
928 }
929
930 static void sdhci_send_command(struct sdhci_host *host, struct mmc_command *cmd)
931 {
932         int flags;
933         u32 mask;
934         unsigned long timeout;
935
936         WARN_ON(host->cmd);
937
938         /* Wait max 10 ms */
939         timeout = 10;
940
941         mask = SDHCI_CMD_INHIBIT;
942         if ((cmd->data != NULL) || (cmd->flags & MMC_RSP_BUSY))
943                 mask |= SDHCI_DATA_INHIBIT;
944
945         /* We shouldn't wait for data inihibit for stop commands, even
946            though they might use busy signaling */
947         if (host->mrq->data && (cmd == host->mrq->data->stop))
948                 mask &= ~SDHCI_DATA_INHIBIT;
949
950         while (sdhci_readl(host, SDHCI_PRESENT_STATE) & mask) {
951                 if (timeout == 0) {
952                         printk(KERN_ERR "%s: Controller never released "
953                                 "inhibit bit(s).\n", mmc_hostname(host->mmc));
954                         sdhci_dumpregs(host);
955                         cmd->error = -EIO;
956                         tasklet_schedule(&host->finish_tasklet);
957                         return;
958                 }
959                 timeout--;
960                 mdelay(1);
961         }
962
963         mod_timer(&host->timer, jiffies + 10 * HZ);
964
965         host->cmd = cmd;
966
967         sdhci_prepare_data(host, cmd);
968
969         sdhci_writel(host, cmd->arg, SDHCI_ARGUMENT);
970
971         sdhci_set_transfer_mode(host, cmd);
972
973         if ((cmd->flags & MMC_RSP_136) && (cmd->flags & MMC_RSP_BUSY)) {
974                 printk(KERN_ERR "%s: Unsupported response type!\n",
975                         mmc_hostname(host->mmc));
976                 cmd->error = -EINVAL;
977                 tasklet_schedule(&host->finish_tasklet);
978                 return;
979         }
980
981         if (!(cmd->flags & MMC_RSP_PRESENT))
982                 flags = SDHCI_CMD_RESP_NONE;
983         else if (cmd->flags & MMC_RSP_136)
984                 flags = SDHCI_CMD_RESP_LONG;
985         else if (cmd->flags & MMC_RSP_BUSY)
986                 flags = SDHCI_CMD_RESP_SHORT_BUSY;
987         else
988                 flags = SDHCI_CMD_RESP_SHORT;
989
990         if (cmd->flags & MMC_RSP_CRC)
991                 flags |= SDHCI_CMD_CRC;
992         if (cmd->flags & MMC_RSP_OPCODE)
993                 flags |= SDHCI_CMD_INDEX;
994
995         /* CMD19 is special in that the Data Present Select should be set */
996         if (cmd->data || (cmd->opcode == MMC_SEND_TUNING_BLOCK))
997                 flags |= SDHCI_CMD_DATA;
998
999         sdhci_writew(host, SDHCI_MAKE_CMD(cmd->opcode, flags), SDHCI_COMMAND);
1000 }
1001
1002 static void sdhci_finish_command(struct sdhci_host *host)
1003 {
1004         int i;
1005
1006         BUG_ON(host->cmd == NULL);
1007
1008         if (host->cmd->flags & MMC_RSP_PRESENT) {
1009                 if (host->cmd->flags & MMC_RSP_136) {
1010                         /* CRC is stripped so we need to do some shifting. */
1011                         for (i = 0;i < 4;i++) {
1012                                 host->cmd->resp[i] = sdhci_readl(host,
1013                                         SDHCI_RESPONSE + (3-i)*4) << 8;
1014                                 if (i != 3)
1015                                         host->cmd->resp[i] |=
1016                                                 sdhci_readb(host,
1017                                                 SDHCI_RESPONSE + (3-i)*4-1);
1018                         }
1019                 } else {
1020                         host->cmd->resp[0] = sdhci_readl(host, SDHCI_RESPONSE);
1021                 }
1022         }
1023
1024         host->cmd->error = 0;
1025
1026         /* Finished CMD23, now send actual command. */
1027         if (host->cmd == host->mrq->sbc) {
1028                 host->cmd = NULL;
1029                 sdhci_send_command(host, host->mrq->cmd);
1030         } else {
1031
1032                 /* Processed actual command. */
1033                 if (host->data && host->data_early)
1034                         sdhci_finish_data(host);
1035
1036                 if (!host->cmd->data)
1037                         tasklet_schedule(&host->finish_tasklet);
1038
1039                 host->cmd = NULL;
1040         }
1041 }
1042
1043 static void sdhci_set_clock(struct sdhci_host *host, unsigned int clock)
1044 {
1045         int div = 0; /* Initialized for compiler warning */
1046         u16 clk = 0;
1047         unsigned long timeout;
1048
1049         if (clock == host->clock)
1050                 return;
1051
1052         if (host->ops->set_clock) {
1053                 host->ops->set_clock(host, clock);
1054                 if (host->quirks & SDHCI_QUIRK_NONSTANDARD_CLOCK)
1055                         return;
1056         }
1057
1058         sdhci_writew(host, 0, SDHCI_CLOCK_CONTROL);
1059
1060         if (clock == 0)
1061                 goto out;
1062
1063         if (host->version >= SDHCI_SPEC_300) {
1064                 /*
1065                  * Check if the Host Controller supports Programmable Clock
1066                  * Mode.
1067                  */
1068                 if (host->clk_mul) {
1069                         u16 ctrl;
1070
1071                         /*
1072                          * We need to figure out whether the Host Driver needs
1073                          * to select Programmable Clock Mode, or the value can
1074                          * be set automatically by the Host Controller based on
1075                          * the Preset Value registers.
1076                          */
1077                         ctrl = sdhci_readw(host, SDHCI_HOST_CONTROL2);
1078                         if (!(ctrl & SDHCI_CTRL_PRESET_VAL_ENABLE)) {
1079                                 for (div = 1; div <= 1024; div++) {
1080                                         if (((host->max_clk * host->clk_mul) /
1081                                               div) <= clock)
1082                                                 break;
1083                                 }
1084                                 /*
1085                                  * Set Programmable Clock Mode in the Clock
1086                                  * Control register.
1087                                  */
1088                                 clk = SDHCI_PROG_CLOCK_MODE;
1089                                 div--;
1090                         }
1091                 } else {
1092                         /* Version 3.00 divisors must be a multiple of 2. */
1093                         if (host->max_clk <= clock)
1094                                 div = 1;
1095                         else {
1096                                 for (div = 2; div < SDHCI_MAX_DIV_SPEC_300;
1097                                      div += 2) {
1098                                         if ((host->max_clk / div) <= clock)
1099                                                 break;
1100                                 }
1101                         }
1102                         div >>= 1;
1103                 }
1104         } else {
1105                 /* Version 2.00 divisors must be a power of 2. */
1106                 for (div = 1; div < SDHCI_MAX_DIV_SPEC_200; div *= 2) {
1107                         if ((host->max_clk / div) <= clock)
1108                                 break;
1109                 }
1110                 div >>= 1;
1111         }
1112
1113         clk |= (div & SDHCI_DIV_MASK) << SDHCI_DIVIDER_SHIFT;
1114         clk |= ((div & SDHCI_DIV_HI_MASK) >> SDHCI_DIV_MASK_LEN)
1115                 << SDHCI_DIVIDER_HI_SHIFT;
1116         clk |= SDHCI_CLOCK_INT_EN;
1117         sdhci_writew(host, clk, SDHCI_CLOCK_CONTROL);
1118
1119         /* Wait max 20 ms */
1120         timeout = 20;
1121         while (!((clk = sdhci_readw(host, SDHCI_CLOCK_CONTROL))
1122                 & SDHCI_CLOCK_INT_STABLE)) {
1123                 if (timeout == 0) {
1124                         printk(KERN_ERR "%s: Internal clock never "
1125                                 "stabilised.\n", mmc_hostname(host->mmc));
1126                         sdhci_dumpregs(host);
1127                         return;
1128                 }
1129                 timeout--;
1130                 mdelay(1);
1131         }
1132
1133         clk |= SDHCI_CLOCK_CARD_EN;
1134         sdhci_writew(host, clk, SDHCI_CLOCK_CONTROL);
1135
1136 out:
1137         host->clock = clock;
1138 }
1139
1140 static void sdhci_set_power(struct sdhci_host *host, unsigned short power)
1141 {
1142         u8 pwr = 0;
1143
1144         if (power != (unsigned short)-1) {
1145                 switch (1 << power) {
1146                 case MMC_VDD_165_195:
1147                         pwr = SDHCI_POWER_180;
1148                         break;
1149                 case MMC_VDD_29_30:
1150                 case MMC_VDD_30_31:
1151                         pwr = SDHCI_POWER_300;
1152                         break;
1153                 case MMC_VDD_32_33:
1154                 case MMC_VDD_33_34:
1155                         pwr = SDHCI_POWER_330;
1156                         break;
1157                 default:
1158                         BUG();
1159                 }
1160         }
1161
1162         if (host->pwr == pwr)
1163                 return;
1164
1165         host->pwr = pwr;
1166
1167         if (pwr == 0) {
1168                 sdhci_writeb(host, 0, SDHCI_POWER_CONTROL);
1169                 return;
1170         }
1171
1172         /*
1173          * Spec says that we should clear the power reg before setting
1174          * a new value. Some controllers don't seem to like this though.
1175          */
1176         if (!(host->quirks & SDHCI_QUIRK_SINGLE_POWER_WRITE))
1177                 sdhci_writeb(host, 0, SDHCI_POWER_CONTROL);
1178
1179         /*
1180          * At least the Marvell CaFe chip gets confused if we set the voltage
1181          * and set turn on power at the same time, so set the voltage first.
1182          */
1183         if (host->quirks & SDHCI_QUIRK_NO_SIMULT_VDD_AND_POWER)
1184                 sdhci_writeb(host, pwr, SDHCI_POWER_CONTROL);
1185
1186         pwr |= SDHCI_POWER_ON;
1187
1188         sdhci_writeb(host, pwr, SDHCI_POWER_CONTROL);
1189
1190         /*
1191          * Some controllers need an extra 10ms delay of 10ms before they
1192          * can apply clock after applying power
1193          */
1194         if (host->quirks & SDHCI_QUIRK_DELAY_AFTER_POWER)
1195                 mdelay(10);
1196 }
1197
1198 /*****************************************************************************\
1199  *                                                                           *
1200  * MMC callbacks                                                             *
1201  *                                                                           *
1202 \*****************************************************************************/
1203
1204 static void sdhci_request(struct mmc_host *mmc, struct mmc_request *mrq)
1205 {
1206         struct sdhci_host *host;
1207         bool present;
1208         unsigned long flags;
1209
1210         host = mmc_priv(mmc);
1211
1212         spin_lock_irqsave(&host->lock, flags);
1213
1214         WARN_ON(host->mrq != NULL);
1215
1216 #ifndef SDHCI_USE_LEDS_CLASS
1217         sdhci_activate_led(host);
1218 #endif
1219
1220         /*
1221          * Ensure we don't send the STOP for non-SET_BLOCK_COUNTED
1222          * requests if Auto-CMD12 is enabled.
1223          */
1224         if (!mrq->sbc && (host->flags & SDHCI_AUTO_CMD12)) {
1225                 if (mrq->stop) {
1226                         mrq->data->stop = NULL;
1227                         mrq->stop = NULL;
1228                 }
1229         }
1230
1231         host->mrq = mrq;
1232
1233         /* If polling, assume that the card is always present. */
1234         if (host->quirks & SDHCI_QUIRK_BROKEN_CARD_DETECTION)
1235                 present = true;
1236         else
1237                 present = sdhci_readl(host, SDHCI_PRESENT_STATE) &
1238                                 SDHCI_CARD_PRESENT;
1239
1240         if (!present || host->flags & SDHCI_DEVICE_DEAD) {
1241                 host->mrq->cmd->error = -ENOMEDIUM;
1242                 tasklet_schedule(&host->finish_tasklet);
1243         } else {
1244                 u32 present_state;
1245
1246                 present_state = sdhci_readl(host, SDHCI_PRESENT_STATE);
1247                 /*
1248                  * Check if the re-tuning timer has already expired and there
1249                  * is no on-going data transfer. If so, we need to execute
1250                  * tuning procedure before sending command.
1251                  */
1252                 if ((host->flags & SDHCI_NEEDS_RETUNING) &&
1253                     !(present_state & (SDHCI_DOING_WRITE | SDHCI_DOING_READ))) {
1254                         spin_unlock_irqrestore(&host->lock, flags);
1255                         sdhci_execute_tuning(mmc);
1256                         spin_lock_irqsave(&host->lock, flags);
1257
1258                         /* Restore original mmc_request structure */
1259                         host->mrq = mrq;
1260                 }
1261
1262                 if (mrq->sbc && !(host->flags & SDHCI_AUTO_CMD23))
1263                         sdhci_send_command(host, mrq->sbc);
1264                 else
1265                         sdhci_send_command(host, mrq->cmd);
1266         }
1267
1268         mmiowb();
1269         spin_unlock_irqrestore(&host->lock, flags);
1270 }
1271
1272 static void sdhci_set_ios(struct mmc_host *mmc, struct mmc_ios *ios)
1273 {
1274         struct sdhci_host *host;
1275         unsigned long flags;
1276         u8 ctrl;
1277
1278         host = mmc_priv(mmc);
1279
1280         spin_lock_irqsave(&host->lock, flags);
1281
1282         if (host->flags & SDHCI_DEVICE_DEAD)
1283                 goto out;
1284
1285         /*
1286          * Reset the chip on each power off.
1287          * Should clear out any weird states.
1288          */
1289         if (ios->power_mode == MMC_POWER_OFF) {
1290                 sdhci_writel(host, 0, SDHCI_SIGNAL_ENABLE);
1291                 sdhci_reinit(host);
1292         }
1293
1294         sdhci_set_clock(host, ios->clock);
1295
1296         if (ios->power_mode == MMC_POWER_OFF)
1297                 sdhci_set_power(host, -1);
1298         else
1299                 sdhci_set_power(host, ios->vdd);
1300
1301         if (host->ops->platform_send_init_74_clocks)
1302                 host->ops->platform_send_init_74_clocks(host, ios->power_mode);
1303
1304         /*
1305          * If your platform has 8-bit width support but is not a v3 controller,
1306          * or if it requires special setup code, you should implement that in
1307          * platform_8bit_width().
1308          */
1309         if (host->ops->platform_8bit_width)
1310                 host->ops->platform_8bit_width(host, ios->bus_width);
1311         else {
1312                 ctrl = sdhci_readb(host, SDHCI_HOST_CONTROL);
1313                 if (ios->bus_width == MMC_BUS_WIDTH_8) {
1314                         ctrl &= ~SDHCI_CTRL_4BITBUS;
1315                         if (host->version >= SDHCI_SPEC_300)
1316                                 ctrl |= SDHCI_CTRL_8BITBUS;
1317                 } else {
1318                         if (host->version >= SDHCI_SPEC_300)
1319                                 ctrl &= ~SDHCI_CTRL_8BITBUS;
1320                         if (ios->bus_width == MMC_BUS_WIDTH_4)
1321                                 ctrl |= SDHCI_CTRL_4BITBUS;
1322                         else
1323                                 ctrl &= ~SDHCI_CTRL_4BITBUS;
1324                 }
1325                 sdhci_writeb(host, ctrl, SDHCI_HOST_CONTROL);
1326         }
1327
1328         ctrl = sdhci_readb(host, SDHCI_HOST_CONTROL);
1329
1330         if ((ios->timing == MMC_TIMING_SD_HS ||
1331              ios->timing == MMC_TIMING_MMC_HS)
1332             && !(host->quirks & SDHCI_QUIRK_NO_HISPD_BIT))
1333                 ctrl |= SDHCI_CTRL_HISPD;
1334         else
1335                 ctrl &= ~SDHCI_CTRL_HISPD;
1336
1337         if (host->version >= SDHCI_SPEC_300) {
1338                 u16 clk, ctrl_2;
1339                 unsigned int clock;
1340
1341                 /* In case of UHS-I modes, set High Speed Enable */
1342                 if ((ios->timing == MMC_TIMING_UHS_SDR50) ||
1343                     (ios->timing == MMC_TIMING_UHS_SDR104) ||
1344                     (ios->timing == MMC_TIMING_UHS_DDR50) ||
1345                     (ios->timing == MMC_TIMING_UHS_SDR25) ||
1346                     (ios->timing == MMC_TIMING_UHS_SDR12))
1347                         ctrl |= SDHCI_CTRL_HISPD;
1348
1349                 ctrl_2 = sdhci_readw(host, SDHCI_HOST_CONTROL2);
1350                 if (!(ctrl_2 & SDHCI_CTRL_PRESET_VAL_ENABLE)) {
1351                         sdhci_writeb(host, ctrl, SDHCI_HOST_CONTROL);
1352                         /*
1353                          * We only need to set Driver Strength if the
1354                          * preset value enable is not set.
1355                          */
1356                         ctrl_2 &= ~SDHCI_CTRL_DRV_TYPE_MASK;
1357                         if (ios->drv_type == MMC_SET_DRIVER_TYPE_A)
1358                                 ctrl_2 |= SDHCI_CTRL_DRV_TYPE_A;
1359                         else if (ios->drv_type == MMC_SET_DRIVER_TYPE_C)
1360                                 ctrl_2 |= SDHCI_CTRL_DRV_TYPE_C;
1361
1362                         sdhci_writew(host, ctrl_2, SDHCI_HOST_CONTROL2);
1363                 } else {
1364                         /*
1365                          * According to SDHC Spec v3.00, if the Preset Value
1366                          * Enable in the Host Control 2 register is set, we
1367                          * need to reset SD Clock Enable before changing High
1368                          * Speed Enable to avoid generating clock gliches.
1369                          */
1370
1371                         /* Reset SD Clock Enable */
1372                         clk = sdhci_readw(host, SDHCI_CLOCK_CONTROL);
1373                         clk &= ~SDHCI_CLOCK_CARD_EN;
1374                         sdhci_writew(host, clk, SDHCI_CLOCK_CONTROL);
1375
1376                         sdhci_writeb(host, ctrl, SDHCI_HOST_CONTROL);
1377
1378                         /* Re-enable SD Clock */
1379                         clock = host->clock;
1380                         host->clock = 0;
1381                         sdhci_set_clock(host, clock);
1382                 }
1383
1384
1385                 /* Reset SD Clock Enable */
1386                 clk = sdhci_readw(host, SDHCI_CLOCK_CONTROL);
1387                 clk &= ~SDHCI_CLOCK_CARD_EN;
1388                 sdhci_writew(host, clk, SDHCI_CLOCK_CONTROL);
1389
1390                 if (host->ops->set_uhs_signaling)
1391                         host->ops->set_uhs_signaling(host, ios->timing);
1392                 else {
1393                         ctrl_2 = sdhci_readw(host, SDHCI_HOST_CONTROL2);
1394                         /* Select Bus Speed Mode for host */
1395                         ctrl_2 &= ~SDHCI_CTRL_UHS_MASK;
1396                         if (ios->timing == MMC_TIMING_UHS_SDR12)
1397                                 ctrl_2 |= SDHCI_CTRL_UHS_SDR12;
1398                         else if (ios->timing == MMC_TIMING_UHS_SDR25)
1399                                 ctrl_2 |= SDHCI_CTRL_UHS_SDR25;
1400                         else if (ios->timing == MMC_TIMING_UHS_SDR50)
1401                                 ctrl_2 |= SDHCI_CTRL_UHS_SDR50;
1402                         else if (ios->timing == MMC_TIMING_UHS_SDR104)
1403                                 ctrl_2 |= SDHCI_CTRL_UHS_SDR104;
1404                         else if (ios->timing == MMC_TIMING_UHS_DDR50)
1405                                 ctrl_2 |= SDHCI_CTRL_UHS_DDR50;
1406                         sdhci_writew(host, ctrl_2, SDHCI_HOST_CONTROL2);
1407                 }
1408
1409                 /* Re-enable SD Clock */
1410                 clock = host->clock;
1411                 host->clock = 0;
1412                 sdhci_set_clock(host, clock);
1413         } else
1414                 sdhci_writeb(host, ctrl, SDHCI_HOST_CONTROL);
1415
1416         /*
1417          * Some (ENE) controllers go apeshit on some ios operation,
1418          * signalling timeout and CRC errors even on CMD0. Resetting
1419          * it on each ios seems to solve the problem.
1420          */
1421         if(host->quirks & SDHCI_QUIRK_RESET_CMD_DATA_ON_IOS)
1422                 sdhci_reset(host, SDHCI_RESET_CMD | SDHCI_RESET_DATA);
1423
1424 out:
1425         mmiowb();
1426         spin_unlock_irqrestore(&host->lock, flags);
1427 }
1428
1429 static int check_ro(struct sdhci_host *host)
1430 {
1431         unsigned long flags;
1432         int is_readonly;
1433
1434         spin_lock_irqsave(&host->lock, flags);
1435
1436         if (host->flags & SDHCI_DEVICE_DEAD)
1437                 is_readonly = 0;
1438         else if (host->ops->get_ro)
1439                 is_readonly = host->ops->get_ro(host);
1440         else
1441                 is_readonly = !(sdhci_readl(host, SDHCI_PRESENT_STATE)
1442                                 & SDHCI_WRITE_PROTECT);
1443
1444         spin_unlock_irqrestore(&host->lock, flags);
1445
1446         /* This quirk needs to be replaced by a callback-function later */
1447         return host->quirks & SDHCI_QUIRK_INVERTED_WRITE_PROTECT ?
1448                 !is_readonly : is_readonly;
1449 }
1450
1451 #define SAMPLE_COUNT    5
1452
1453 static int sdhci_get_ro(struct mmc_host *mmc)
1454 {
1455         struct sdhci_host *host;
1456         int i, ro_count;
1457
1458         host = mmc_priv(mmc);
1459
1460         if (!(host->quirks & SDHCI_QUIRK_UNSTABLE_RO_DETECT))
1461                 return check_ro(host);
1462
1463         ro_count = 0;
1464         for (i = 0; i < SAMPLE_COUNT; i++) {
1465                 if (check_ro(host)) {
1466                         if (++ro_count > SAMPLE_COUNT / 2)
1467                                 return 1;
1468                 }
1469                 msleep(30);
1470         }
1471         return 0;
1472 }
1473
1474 static void sdhci_enable_sdio_irq(struct mmc_host *mmc, int enable)
1475 {
1476         struct sdhci_host *host;
1477         unsigned long flags;
1478
1479         host = mmc_priv(mmc);
1480
1481         spin_lock_irqsave(&host->lock, flags);
1482
1483         if (host->flags & SDHCI_DEVICE_DEAD)
1484                 goto out;
1485
1486         if (enable)
1487                 sdhci_unmask_irqs(host, SDHCI_INT_CARD_INT);
1488         else
1489                 sdhci_mask_irqs(host, SDHCI_INT_CARD_INT);
1490 out:
1491         mmiowb();
1492
1493         spin_unlock_irqrestore(&host->lock, flags);
1494 }
1495
1496 static int sdhci_start_signal_voltage_switch(struct mmc_host *mmc,
1497         struct mmc_ios *ios)
1498 {
1499         struct sdhci_host *host;
1500         u8 pwr;
1501         u16 clk, ctrl;
1502         u32 present_state;
1503
1504         host = mmc_priv(mmc);
1505
1506         /*
1507          * Signal Voltage Switching is only applicable for Host Controllers
1508          * v3.00 and above.
1509          */
1510         if (host->version < SDHCI_SPEC_300)
1511                 return 0;
1512
1513         /*
1514          * We first check whether the request is to set signalling voltage
1515          * to 3.3V. If so, we change the voltage to 3.3V and return quickly.
1516          */
1517         ctrl = sdhci_readw(host, SDHCI_HOST_CONTROL2);
1518         if (ios->signal_voltage == MMC_SIGNAL_VOLTAGE_330) {
1519                 /* Set 1.8V Signal Enable in the Host Control2 register to 0 */
1520                 ctrl &= ~SDHCI_CTRL_VDD_180;
1521                 sdhci_writew(host, ctrl, SDHCI_HOST_CONTROL2);
1522
1523                 /* Wait for 5ms */
1524                 usleep_range(5000, 5500);
1525
1526                 /* 3.3V regulator output should be stable within 5 ms */
1527                 ctrl = sdhci_readw(host, SDHCI_HOST_CONTROL2);
1528                 if (!(ctrl & SDHCI_CTRL_VDD_180))
1529                         return 0;
1530                 else {
1531                         printk(KERN_INFO DRIVER_NAME ": Switching to 3.3V "
1532                                 "signalling voltage failed\n");
1533                         return -EIO;
1534                 }
1535         } else if (!(ctrl & SDHCI_CTRL_VDD_180) &&
1536                   (ios->signal_voltage == MMC_SIGNAL_VOLTAGE_180)) {
1537                 /* Stop SDCLK */
1538                 clk = sdhci_readw(host, SDHCI_CLOCK_CONTROL);
1539                 clk &= ~SDHCI_CLOCK_CARD_EN;
1540                 sdhci_writew(host, clk, SDHCI_CLOCK_CONTROL);
1541
1542                 /* Check whether DAT[3:0] is 0000 */
1543                 present_state = sdhci_readl(host, SDHCI_PRESENT_STATE);
1544                 if (!((present_state & SDHCI_DATA_LVL_MASK) >>
1545                        SDHCI_DATA_LVL_SHIFT)) {
1546                         /*
1547                          * Enable 1.8V Signal Enable in the Host Control2
1548                          * register
1549                          */
1550                         ctrl |= SDHCI_CTRL_VDD_180;
1551                         sdhci_writew(host, ctrl, SDHCI_HOST_CONTROL2);
1552
1553                         /* Wait for 5ms */
1554                         usleep_range(5000, 5500);
1555
1556                         ctrl = sdhci_readw(host, SDHCI_HOST_CONTROL2);
1557                         if (ctrl & SDHCI_CTRL_VDD_180) {
1558                                 /* Provide SDCLK again and wait for 1ms*/
1559                                 clk = sdhci_readw(host, SDHCI_CLOCK_CONTROL);
1560                                 clk |= SDHCI_CLOCK_CARD_EN;
1561                                 sdhci_writew(host, clk, SDHCI_CLOCK_CONTROL);
1562                                 usleep_range(1000, 1500);
1563
1564                                 /*
1565                                  * If DAT[3:0] level is 1111b, then the card
1566                                  * was successfully switched to 1.8V signaling.
1567                                  */
1568                                 present_state = sdhci_readl(host,
1569                                                         SDHCI_PRESENT_STATE);
1570                                 if ((present_state & SDHCI_DATA_LVL_MASK) ==
1571                                      SDHCI_DATA_LVL_MASK)
1572                                         return 0;
1573                         }
1574                 }
1575
1576                 /*
1577                  * If we are here, that means the switch to 1.8V signaling
1578                  * failed. We power cycle the card, and retry initialization
1579                  * sequence by setting S18R to 0.
1580                  */
1581                 pwr = sdhci_readb(host, SDHCI_POWER_CONTROL);
1582                 pwr &= ~SDHCI_POWER_ON;
1583                 sdhci_writeb(host, pwr, SDHCI_POWER_CONTROL);
1584
1585                 /* Wait for 1ms as per the spec */
1586                 usleep_range(1000, 1500);
1587                 pwr |= SDHCI_POWER_ON;
1588                 sdhci_writeb(host, pwr, SDHCI_POWER_CONTROL);
1589
1590                 printk(KERN_INFO DRIVER_NAME ": Switching to 1.8V signalling "
1591                         "voltage failed, retrying with S18R set to 0\n");
1592                 return -EAGAIN;
1593         } else
1594                 /* No signal voltage switch required */
1595                 return 0;
1596 }
1597
1598 static int sdhci_execute_tuning(struct mmc_host *mmc)
1599 {
1600         struct sdhci_host *host;
1601         u16 ctrl;
1602         u32 ier;
1603         int tuning_loop_counter = MAX_TUNING_LOOP;
1604         unsigned long timeout;
1605         int err = 0;
1606
1607         host = mmc_priv(mmc);
1608
1609         disable_irq(host->irq);
1610         spin_lock(&host->lock);
1611
1612         ctrl = sdhci_readw(host, SDHCI_HOST_CONTROL2);
1613
1614         /*
1615          * Host Controller needs tuning only in case of SDR104 mode
1616          * and for SDR50 mode when Use Tuning for SDR50 is set in
1617          * Capabilities register.
1618          */
1619         if (((ctrl & SDHCI_CTRL_UHS_MASK) == SDHCI_CTRL_UHS_SDR104) ||
1620             (((ctrl & SDHCI_CTRL_UHS_MASK) == SDHCI_CTRL_UHS_SDR50) &&
1621             (host->flags & SDHCI_SDR50_NEEDS_TUNING)))
1622                 ctrl |= SDHCI_CTRL_EXEC_TUNING;
1623         else {
1624                 spin_unlock(&host->lock);
1625                 enable_irq(host->irq);
1626                 return 0;
1627         }
1628
1629         sdhci_writew(host, ctrl, SDHCI_HOST_CONTROL2);
1630
1631         /*
1632          * As per the Host Controller spec v3.00, tuning command
1633          * generates Buffer Read Ready interrupt, so enable that.
1634          *
1635          * Note: The spec clearly says that when tuning sequence
1636          * is being performed, the controller does not generate
1637          * interrupts other than Buffer Read Ready interrupt. But
1638          * to make sure we don't hit a controller bug, we _only_
1639          * enable Buffer Read Ready interrupt here.
1640          */
1641         ier = sdhci_readl(host, SDHCI_INT_ENABLE);
1642         sdhci_clear_set_irqs(host, ier, SDHCI_INT_DATA_AVAIL);
1643
1644         /*
1645          * Issue CMD19 repeatedly till Execute Tuning is set to 0 or the number
1646          * of loops reaches 40 times or a timeout of 150ms occurs.
1647          */
1648         timeout = 150;
1649         do {
1650                 struct mmc_command cmd = {0};
1651                 struct mmc_request mrq = {0};
1652
1653                 if (!tuning_loop_counter && !timeout)
1654                         break;
1655
1656                 cmd.opcode = MMC_SEND_TUNING_BLOCK;
1657                 cmd.arg = 0;
1658                 cmd.flags = MMC_RSP_R1 | MMC_CMD_ADTC;
1659                 cmd.retries = 0;
1660                 cmd.data = NULL;
1661                 cmd.error = 0;
1662
1663                 mrq.cmd = &cmd;
1664                 host->mrq = &mrq;
1665
1666                 /*
1667                  * In response to CMD19, the card sends 64 bytes of tuning
1668                  * block to the Host Controller. So we set the block size
1669                  * to 64 here.
1670                  */
1671                 sdhci_writew(host, SDHCI_MAKE_BLKSZ(7, 64), SDHCI_BLOCK_SIZE);
1672
1673                 /*
1674                  * The tuning block is sent by the card to the host controller.
1675                  * So we set the TRNS_READ bit in the Transfer Mode register.
1676                  * This also takes care of setting DMA Enable and Multi Block
1677                  * Select in the same register to 0.
1678                  */
1679                 sdhci_writew(host, SDHCI_TRNS_READ, SDHCI_TRANSFER_MODE);
1680
1681                 sdhci_send_command(host, &cmd);
1682
1683                 host->cmd = NULL;
1684                 host->mrq = NULL;
1685
1686                 spin_unlock(&host->lock);
1687                 enable_irq(host->irq);
1688
1689                 /* Wait for Buffer Read Ready interrupt */
1690                 wait_event_interruptible_timeout(host->buf_ready_int,
1691                                         (host->tuning_done == 1),
1692                                         msecs_to_jiffies(50));
1693                 disable_irq(host->irq);
1694                 spin_lock(&host->lock);
1695
1696                 if (!host->tuning_done) {
1697                         printk(KERN_INFO DRIVER_NAME ": Timeout waiting for "
1698                                 "Buffer Read Ready interrupt during tuning "
1699                                 "procedure, falling back to fixed sampling "
1700                                 "clock\n");
1701                         ctrl = sdhci_readw(host, SDHCI_HOST_CONTROL2);
1702                         ctrl &= ~SDHCI_CTRL_TUNED_CLK;
1703                         ctrl &= ~SDHCI_CTRL_EXEC_TUNING;
1704                         sdhci_writew(host, ctrl, SDHCI_HOST_CONTROL2);
1705
1706                         err = -EIO;
1707                         goto out;
1708                 }
1709
1710                 host->tuning_done = 0;
1711
1712                 ctrl = sdhci_readw(host, SDHCI_HOST_CONTROL2);
1713                 tuning_loop_counter--;
1714                 timeout--;
1715                 mdelay(1);
1716         } while (ctrl & SDHCI_CTRL_EXEC_TUNING);
1717
1718         /*
1719          * The Host Driver has exhausted the maximum number of loops allowed,
1720          * so use fixed sampling frequency.
1721          */
1722         if (!tuning_loop_counter || !timeout) {
1723                 ctrl &= ~SDHCI_CTRL_TUNED_CLK;
1724                 sdhci_writew(host, ctrl, SDHCI_HOST_CONTROL2);
1725         } else {
1726                 if (!(ctrl & SDHCI_CTRL_TUNED_CLK)) {
1727                         printk(KERN_INFO DRIVER_NAME ": Tuning procedure"
1728                                 " failed, falling back to fixed sampling"
1729                                 " clock\n");
1730                         err = -EIO;
1731                 }
1732         }
1733
1734 out:
1735         /*
1736          * If this is the very first time we are here, we start the retuning
1737          * timer. Since only during the first time, SDHCI_NEEDS_RETUNING
1738          * flag won't be set, we check this condition before actually starting
1739          * the timer.
1740          */
1741         if (!(host->flags & SDHCI_NEEDS_RETUNING) && host->tuning_count &&
1742             (host->tuning_mode == SDHCI_TUNING_MODE_1)) {
1743                 mod_timer(&host->tuning_timer, jiffies +
1744                         host->tuning_count * HZ);
1745                 /* Tuning mode 1 limits the maximum data length to 4MB */
1746                 mmc->max_blk_count = (4 * 1024 * 1024) / mmc->max_blk_size;
1747         } else {
1748                 host->flags &= ~SDHCI_NEEDS_RETUNING;
1749                 /* Reload the new initial value for timer */
1750                 if (host->tuning_mode == SDHCI_TUNING_MODE_1)
1751                         mod_timer(&host->tuning_timer, jiffies +
1752                                 host->tuning_count * HZ);
1753         }
1754
1755         /*
1756          * In case tuning fails, host controllers which support re-tuning can
1757          * try tuning again at a later time, when the re-tuning timer expires.
1758          * So for these controllers, we return 0. Since there might be other
1759          * controllers who do not have this capability, we return error for
1760          * them.
1761          */
1762         if (err && host->tuning_count &&
1763             host->tuning_mode == SDHCI_TUNING_MODE_1)
1764                 err = 0;
1765
1766         sdhci_clear_set_irqs(host, SDHCI_INT_DATA_AVAIL, ier);
1767         spin_unlock(&host->lock);
1768         enable_irq(host->irq);
1769
1770         return err;
1771 }
1772
1773 static void sdhci_enable_preset_value(struct mmc_host *mmc, bool enable)
1774 {
1775         struct sdhci_host *host;
1776         u16 ctrl;
1777         unsigned long flags;
1778
1779         host = mmc_priv(mmc);
1780
1781         /* Host Controller v3.00 defines preset value registers */
1782         if (host->version < SDHCI_SPEC_300)
1783                 return;
1784
1785         spin_lock_irqsave(&host->lock, flags);
1786
1787         ctrl = sdhci_readw(host, SDHCI_HOST_CONTROL2);
1788
1789         /*
1790          * We only enable or disable Preset Value if they are not already
1791          * enabled or disabled respectively. Otherwise, we bail out.
1792          */
1793         if (enable && !(ctrl & SDHCI_CTRL_PRESET_VAL_ENABLE)) {
1794                 ctrl |= SDHCI_CTRL_PRESET_VAL_ENABLE;
1795                 sdhci_writew(host, ctrl, SDHCI_HOST_CONTROL2);
1796         } else if (!enable && (ctrl & SDHCI_CTRL_PRESET_VAL_ENABLE)) {
1797                 ctrl &= ~SDHCI_CTRL_PRESET_VAL_ENABLE;
1798                 sdhci_writew(host, ctrl, SDHCI_HOST_CONTROL2);
1799         }
1800
1801         spin_unlock_irqrestore(&host->lock, flags);
1802 }
1803
1804 static const struct mmc_host_ops sdhci_ops = {
1805         .request        = sdhci_request,
1806         .set_ios        = sdhci_set_ios,
1807         .get_ro         = sdhci_get_ro,
1808         .enable_sdio_irq = sdhci_enable_sdio_irq,
1809         .start_signal_voltage_switch    = sdhci_start_signal_voltage_switch,
1810         .execute_tuning                 = sdhci_execute_tuning,
1811         .enable_preset_value            = sdhci_enable_preset_value,
1812 };
1813
1814 /*****************************************************************************\
1815  *                                                                           *
1816  * Tasklets                                                                  *
1817  *                                                                           *
1818 \*****************************************************************************/
1819
1820 static void sdhci_tasklet_card(unsigned long param)
1821 {
1822         struct sdhci_host *host;
1823         unsigned long flags;
1824
1825         host = (struct sdhci_host*)param;
1826
1827         spin_lock_irqsave(&host->lock, flags);
1828
1829         if (!(sdhci_readl(host, SDHCI_PRESENT_STATE) & SDHCI_CARD_PRESENT)) {
1830                 if (host->mrq) {
1831                         printk(KERN_ERR "%s: Card removed during transfer!\n",
1832                                 mmc_hostname(host->mmc));
1833                         printk(KERN_ERR "%s: Resetting controller.\n",
1834                                 mmc_hostname(host->mmc));
1835
1836                         sdhci_reset(host, SDHCI_RESET_CMD);
1837                         sdhci_reset(host, SDHCI_RESET_DATA);
1838
1839                         host->mrq->cmd->error = -ENOMEDIUM;
1840                         tasklet_schedule(&host->finish_tasklet);
1841                 }
1842         }
1843
1844         spin_unlock_irqrestore(&host->lock, flags);
1845
1846         mmc_detect_change(host->mmc, msecs_to_jiffies(200));
1847 }
1848
1849 static void sdhci_tasklet_finish(unsigned long param)
1850 {
1851         struct sdhci_host *host;
1852         unsigned long flags;
1853         struct mmc_request *mrq;
1854
1855         host = (struct sdhci_host*)param;
1856
1857         /*
1858          * If this tasklet gets rescheduled while running, it will
1859          * be run again afterwards but without any active request.
1860          */
1861         if (!host->mrq)
1862                 return;
1863
1864         spin_lock_irqsave(&host->lock, flags);
1865
1866         del_timer(&host->timer);
1867
1868         mrq = host->mrq;
1869
1870         /*
1871          * The controller needs a reset of internal state machines
1872          * upon error conditions.
1873          */
1874         if (!(host->flags & SDHCI_DEVICE_DEAD) &&
1875             ((mrq->cmd && mrq->cmd->error) ||
1876                  (mrq->data && (mrq->data->error ||
1877                   (mrq->data->stop && mrq->data->stop->error))) ||
1878                    (host->quirks & SDHCI_QUIRK_RESET_AFTER_REQUEST))) {
1879
1880                 /* Some controllers need this kick or reset won't work here */
1881                 if (host->quirks & SDHCI_QUIRK_CLOCK_BEFORE_RESET) {
1882                         unsigned int clock;
1883
1884                         /* This is to force an update */
1885                         clock = host->clock;
1886                         host->clock = 0;
1887                         sdhci_set_clock(host, clock);
1888                 }
1889
1890                 /* Spec says we should do both at the same time, but Ricoh
1891                    controllers do not like that. */
1892                 sdhci_reset(host, SDHCI_RESET_CMD);
1893                 sdhci_reset(host, SDHCI_RESET_DATA);
1894         }
1895
1896         host->mrq = NULL;
1897         host->cmd = NULL;
1898         host->data = NULL;
1899
1900 #ifndef SDHCI_USE_LEDS_CLASS
1901         sdhci_deactivate_led(host);
1902 #endif
1903
1904         mmiowb();
1905         spin_unlock_irqrestore(&host->lock, flags);
1906
1907         mmc_request_done(host->mmc, mrq);
1908 }
1909
1910 static void sdhci_timeout_timer(unsigned long data)
1911 {
1912         struct sdhci_host *host;
1913         unsigned long flags;
1914
1915         host = (struct sdhci_host*)data;
1916
1917         spin_lock_irqsave(&host->lock, flags);
1918
1919         if (host->mrq) {
1920                 printk(KERN_ERR "%s: Timeout waiting for hardware "
1921                         "interrupt.\n", mmc_hostname(host->mmc));
1922                 sdhci_dumpregs(host);
1923
1924                 if (host->data) {
1925                         host->data->error = -ETIMEDOUT;
1926                         sdhci_finish_data(host);
1927                 } else {
1928                         if (host->cmd)
1929                                 host->cmd->error = -ETIMEDOUT;
1930                         else
1931                                 host->mrq->cmd->error = -ETIMEDOUT;
1932
1933                         tasklet_schedule(&host->finish_tasklet);
1934                 }
1935         }
1936
1937         mmiowb();
1938         spin_unlock_irqrestore(&host->lock, flags);
1939 }
1940
1941 static void sdhci_tuning_timer(unsigned long data)
1942 {
1943         struct sdhci_host *host;
1944         unsigned long flags;
1945
1946         host = (struct sdhci_host *)data;
1947
1948         spin_lock_irqsave(&host->lock, flags);
1949
1950         host->flags |= SDHCI_NEEDS_RETUNING;
1951
1952         spin_unlock_irqrestore(&host->lock, flags);
1953 }
1954
1955 /*****************************************************************************\
1956  *                                                                           *
1957  * Interrupt handling                                                        *
1958  *                                                                           *
1959 \*****************************************************************************/
1960
1961 static void sdhci_cmd_irq(struct sdhci_host *host, u32 intmask)
1962 {
1963         BUG_ON(intmask == 0);
1964
1965         if (!host->cmd) {
1966                 printk(KERN_ERR "%s: Got command interrupt 0x%08x even "
1967                         "though no command operation was in progress.\n",
1968                         mmc_hostname(host->mmc), (unsigned)intmask);
1969                 sdhci_dumpregs(host);
1970                 return;
1971         }
1972
1973         if (intmask & SDHCI_INT_TIMEOUT)
1974                 host->cmd->error = -ETIMEDOUT;
1975         else if (intmask & (SDHCI_INT_CRC | SDHCI_INT_END_BIT |
1976                         SDHCI_INT_INDEX))
1977                 host->cmd->error = -EILSEQ;
1978
1979         if (host->cmd->error) {
1980                 tasklet_schedule(&host->finish_tasklet);
1981                 return;
1982         }
1983
1984         /*
1985          * The host can send and interrupt when the busy state has
1986          * ended, allowing us to wait without wasting CPU cycles.
1987          * Unfortunately this is overloaded on the "data complete"
1988          * interrupt, so we need to take some care when handling
1989          * it.
1990          *
1991          * Note: The 1.0 specification is a bit ambiguous about this
1992          *       feature so there might be some problems with older
1993          *       controllers.
1994          */
1995         if (host->cmd->flags & MMC_RSP_BUSY) {
1996                 if (host->cmd->data)
1997                         DBG("Cannot wait for busy signal when also "
1998                                 "doing a data transfer");
1999                 else if (!(host->quirks & SDHCI_QUIRK_NO_BUSY_IRQ))
2000                         return;
2001
2002                 /* The controller does not support the end-of-busy IRQ,
2003                  * fall through and take the SDHCI_INT_RESPONSE */
2004         }
2005
2006         if (intmask & SDHCI_INT_RESPONSE)
2007                 sdhci_finish_command(host);
2008 }
2009
2010 #ifdef CONFIG_MMC_DEBUG
2011 static void sdhci_show_adma_error(struct sdhci_host *host)
2012 {
2013         const char *name = mmc_hostname(host->mmc);
2014         u8 *desc = host->adma_desc;
2015         __le32 *dma;
2016         __le16 *len;
2017         u8 attr;
2018
2019         sdhci_dumpregs(host);
2020
2021         while (true) {
2022                 dma = (__le32 *)(desc + 4);
2023                 len = (__le16 *)(desc + 2);
2024                 attr = *desc;
2025
2026                 DBG("%s: %p: DMA 0x%08x, LEN 0x%04x, Attr=0x%02x\n",
2027                     name, desc, le32_to_cpu(*dma), le16_to_cpu(*len), attr);
2028
2029                 desc += 8;
2030
2031                 if (attr & 2)
2032                         break;
2033         }
2034 }
2035 #else
2036 static void sdhci_show_adma_error(struct sdhci_host *host) { }
2037 #endif
2038
2039 static void sdhci_data_irq(struct sdhci_host *host, u32 intmask)
2040 {
2041         BUG_ON(intmask == 0);
2042
2043         /* CMD19 generates _only_ Buffer Read Ready interrupt */
2044         if (intmask & SDHCI_INT_DATA_AVAIL) {
2045                 if (SDHCI_GET_CMD(sdhci_readw(host, SDHCI_COMMAND)) ==
2046                     MMC_SEND_TUNING_BLOCK) {
2047                         host->tuning_done = 1;
2048                         wake_up(&host->buf_ready_int);
2049                         return;
2050                 }
2051         }
2052
2053         if (!host->data) {
2054                 /*
2055                  * The "data complete" interrupt is also used to
2056                  * indicate that a busy state has ended. See comment
2057                  * above in sdhci_cmd_irq().
2058                  */
2059                 if (host->cmd && (host->cmd->flags & MMC_RSP_BUSY)) {
2060                         if (intmask & SDHCI_INT_DATA_END) {
2061                                 sdhci_finish_command(host);
2062                                 return;
2063                         }
2064                 }
2065
2066                 printk(KERN_ERR "%s: Got data interrupt 0x%08x even "
2067                         "though no data operation was in progress.\n",
2068                         mmc_hostname(host->mmc), (unsigned)intmask);
2069                 sdhci_dumpregs(host);
2070
2071                 return;
2072         }
2073
2074         if (intmask & SDHCI_INT_DATA_TIMEOUT)
2075                 host->data->error = -ETIMEDOUT;
2076         else if (intmask & SDHCI_INT_DATA_END_BIT)
2077                 host->data->error = -EILSEQ;
2078         else if ((intmask & SDHCI_INT_DATA_CRC) &&
2079                 SDHCI_GET_CMD(sdhci_readw(host, SDHCI_COMMAND))
2080                         != MMC_BUS_TEST_R)
2081                 host->data->error = -EILSEQ;
2082         else if (intmask & SDHCI_INT_ADMA_ERROR) {
2083                 printk(KERN_ERR "%s: ADMA error\n", mmc_hostname(host->mmc));
2084                 sdhci_show_adma_error(host);
2085                 host->data->error = -EIO;
2086         }
2087
2088         if (host->data->error)
2089                 sdhci_finish_data(host);
2090         else {
2091                 if (intmask & (SDHCI_INT_DATA_AVAIL | SDHCI_INT_SPACE_AVAIL))
2092                         sdhci_transfer_pio(host);
2093
2094                 /*
2095                  * We currently don't do anything fancy with DMA
2096                  * boundaries, but as we can't disable the feature
2097                  * we need to at least restart the transfer.
2098                  *
2099                  * According to the spec sdhci_readl(host, SDHCI_DMA_ADDRESS)
2100                  * should return a valid address to continue from, but as
2101                  * some controllers are faulty, don't trust them.
2102                  */
2103                 if (intmask & SDHCI_INT_DMA_END) {
2104                         u32 dmastart, dmanow;
2105                         dmastart = sg_dma_address(host->data->sg);
2106                         dmanow = dmastart + host->data->bytes_xfered;
2107                         /*
2108                          * Force update to the next DMA block boundary.
2109                          */
2110                         dmanow = (dmanow &
2111                                 ~(SDHCI_DEFAULT_BOUNDARY_SIZE - 1)) +
2112                                 SDHCI_DEFAULT_BOUNDARY_SIZE;
2113                         host->data->bytes_xfered = dmanow - dmastart;
2114                         DBG("%s: DMA base 0x%08x, transferred 0x%06x bytes,"
2115                                 " next 0x%08x\n",
2116                                 mmc_hostname(host->mmc), dmastart,
2117                                 host->data->bytes_xfered, dmanow);
2118                         sdhci_writel(host, dmanow, SDHCI_DMA_ADDRESS);
2119                 }
2120
2121                 if (intmask & SDHCI_INT_DATA_END) {
2122                         if (host->cmd) {
2123                                 /*
2124                                  * Data managed to finish before the
2125                                  * command completed. Make sure we do
2126                                  * things in the proper order.
2127                                  */
2128                                 host->data_early = 1;
2129                         } else {
2130                                 sdhci_finish_data(host);
2131                         }
2132                 }
2133         }
2134 }
2135
2136 static irqreturn_t sdhci_irq(int irq, void *dev_id)
2137 {
2138         irqreturn_t result;
2139         struct sdhci_host* host = dev_id;
2140         u32 intmask;
2141         int cardint = 0;
2142
2143         spin_lock(&host->lock);
2144
2145         intmask = sdhci_readl(host, SDHCI_INT_STATUS);
2146
2147         if (!intmask || intmask == 0xffffffff) {
2148                 result = IRQ_NONE;
2149                 goto out;
2150         }
2151
2152         DBG("*** %s got interrupt: 0x%08x\n",
2153                 mmc_hostname(host->mmc), intmask);
2154
2155         if (intmask & (SDHCI_INT_CARD_INSERT | SDHCI_INT_CARD_REMOVE)) {
2156                 u32 present = sdhci_readl(host, SDHCI_PRESENT_STATE) &
2157                               SDHCI_CARD_PRESENT;
2158
2159                 /*
2160                  * There is a observation on i.mx esdhc.  INSERT bit will be
2161                  * immediately set again when it gets cleared, if a card is
2162                  * inserted.  We have to mask the irq to prevent interrupt
2163                  * storm which will freeze the system.  And the REMOVE gets
2164                  * the same situation.
2165                  *
2166                  * More testing are needed here to ensure it works for other
2167                  * platforms though.
2168                  */
2169                 sdhci_mask_irqs(host, present ? SDHCI_INT_CARD_INSERT :
2170                                                 SDHCI_INT_CARD_REMOVE);
2171                 sdhci_unmask_irqs(host, present ? SDHCI_INT_CARD_REMOVE :
2172                                                   SDHCI_INT_CARD_INSERT);
2173
2174                 sdhci_writel(host, intmask & (SDHCI_INT_CARD_INSERT |
2175                              SDHCI_INT_CARD_REMOVE), SDHCI_INT_STATUS);
2176                 intmask &= ~(SDHCI_INT_CARD_INSERT | SDHCI_INT_CARD_REMOVE);
2177                 tasklet_schedule(&host->card_tasklet);
2178         }
2179
2180         if (intmask & SDHCI_INT_CMD_MASK) {
2181                 sdhci_writel(host, intmask & SDHCI_INT_CMD_MASK,
2182                         SDHCI_INT_STATUS);
2183                 sdhci_cmd_irq(host, intmask & SDHCI_INT_CMD_MASK);
2184         }
2185
2186         if (intmask & SDHCI_INT_DATA_MASK) {
2187                 sdhci_writel(host, intmask & SDHCI_INT_DATA_MASK,
2188                         SDHCI_INT_STATUS);
2189                 sdhci_data_irq(host, intmask & SDHCI_INT_DATA_MASK);
2190         }
2191
2192         intmask &= ~(SDHCI_INT_CMD_MASK | SDHCI_INT_DATA_MASK);
2193
2194         intmask &= ~SDHCI_INT_ERROR;
2195
2196         if (intmask & SDHCI_INT_BUS_POWER) {
2197                 printk(KERN_ERR "%s: Card is consuming too much power!\n",
2198                         mmc_hostname(host->mmc));
2199                 sdhci_writel(host, SDHCI_INT_BUS_POWER, SDHCI_INT_STATUS);
2200         }
2201
2202         intmask &= ~SDHCI_INT_BUS_POWER;
2203
2204         if (intmask & SDHCI_INT_CARD_INT)
2205                 cardint = 1;
2206
2207         intmask &= ~SDHCI_INT_CARD_INT;
2208
2209         if (intmask) {
2210                 printk(KERN_ERR "%s: Unexpected interrupt 0x%08x.\n",
2211                         mmc_hostname(host->mmc), intmask);
2212                 sdhci_dumpregs(host);
2213
2214                 sdhci_writel(host, intmask, SDHCI_INT_STATUS);
2215         }
2216
2217         result = IRQ_HANDLED;
2218
2219         mmiowb();
2220 out:
2221         spin_unlock(&host->lock);
2222
2223         /*
2224          * We have to delay this as it calls back into the driver.
2225          */
2226         if (cardint)
2227                 mmc_signal_sdio_irq(host->mmc);
2228
2229         return result;
2230 }
2231
2232 /*****************************************************************************\
2233  *                                                                           *
2234  * Suspend/resume                                                            *
2235  *                                                                           *
2236 \*****************************************************************************/
2237
2238 #ifdef CONFIG_PM
2239
2240 int sdhci_suspend_host(struct sdhci_host *host, pm_message_t state)
2241 {
2242         int ret;
2243
2244         sdhci_disable_card_detection(host);
2245
2246         /* Disable tuning since we are suspending */
2247         if (host->version >= SDHCI_SPEC_300 && host->tuning_count &&
2248             host->tuning_mode == SDHCI_TUNING_MODE_1) {
2249                 host->flags &= ~SDHCI_NEEDS_RETUNING;
2250                 mod_timer(&host->tuning_timer, jiffies +
2251                         host->tuning_count * HZ);
2252         }
2253
2254         ret = mmc_suspend_host(host->mmc);
2255         if (ret)
2256                 return ret;
2257
2258         free_irq(host->irq, host);
2259
2260         if (host->vmmc)
2261                 ret = regulator_disable(host->vmmc);
2262
2263         return ret;
2264 }
2265
2266 EXPORT_SYMBOL_GPL(sdhci_suspend_host);
2267
2268 int sdhci_resume_host(struct sdhci_host *host)
2269 {
2270         int ret;
2271
2272         if (host->vmmc) {
2273                 int ret = regulator_enable(host->vmmc);
2274                 if (ret)
2275                         return ret;
2276         }
2277
2278
2279         if (host->flags & (SDHCI_USE_SDMA | SDHCI_USE_ADMA)) {
2280                 if (host->ops->enable_dma)
2281                         host->ops->enable_dma(host);
2282         }
2283
2284         ret = request_irq(host->irq, sdhci_irq, IRQF_SHARED,
2285                           mmc_hostname(host->mmc), host);
2286         if (ret)
2287                 return ret;
2288
2289         sdhci_init(host, (host->mmc->pm_flags & MMC_PM_KEEP_POWER));
2290         mmiowb();
2291
2292         ret = mmc_resume_host(host->mmc);
2293         sdhci_enable_card_detection(host);
2294
2295         /* Set the re-tuning expiration flag */
2296         if ((host->version >= SDHCI_SPEC_300) && host->tuning_count &&
2297             (host->tuning_mode == SDHCI_TUNING_MODE_1))
2298                 host->flags |= SDHCI_NEEDS_RETUNING;
2299
2300         return ret;
2301 }
2302
2303 EXPORT_SYMBOL_GPL(sdhci_resume_host);
2304
2305 void sdhci_enable_irq_wakeups(struct sdhci_host *host)
2306 {
2307         u8 val;
2308         val = sdhci_readb(host, SDHCI_WAKE_UP_CONTROL);
2309         val |= SDHCI_WAKE_ON_INT;
2310         sdhci_writeb(host, val, SDHCI_WAKE_UP_CONTROL);
2311 }
2312
2313 EXPORT_SYMBOL_GPL(sdhci_enable_irq_wakeups);
2314
2315 #endif /* CONFIG_PM */
2316
2317 /*****************************************************************************\
2318  *                                                                           *
2319  * Device allocation/registration                                            *
2320  *                                                                           *
2321 \*****************************************************************************/
2322
2323 struct sdhci_host *sdhci_alloc_host(struct device *dev,
2324         size_t priv_size)
2325 {
2326         struct mmc_host *mmc;
2327         struct sdhci_host *host;
2328
2329         WARN_ON(dev == NULL);
2330
2331         mmc = mmc_alloc_host(sizeof(struct sdhci_host) + priv_size, dev);
2332         if (!mmc)
2333                 return ERR_PTR(-ENOMEM);
2334
2335         host = mmc_priv(mmc);
2336         host->mmc = mmc;
2337
2338         return host;
2339 }
2340
2341 EXPORT_SYMBOL_GPL(sdhci_alloc_host);
2342
2343 int sdhci_add_host(struct sdhci_host *host)
2344 {
2345         struct mmc_host *mmc;
2346         u32 caps[2];
2347         u32 max_current_caps;
2348         unsigned int ocr_avail;
2349         int ret;
2350
2351         WARN_ON(host == NULL);
2352         if (host == NULL)
2353                 return -EINVAL;
2354
2355         mmc = host->mmc;
2356
2357         if (debug_quirks)
2358                 host->quirks = debug_quirks;
2359
2360         sdhci_reset(host, SDHCI_RESET_ALL);
2361
2362         host->version = sdhci_readw(host, SDHCI_HOST_VERSION);
2363         host->version = (host->version & SDHCI_SPEC_VER_MASK)
2364                                 >> SDHCI_SPEC_VER_SHIFT;
2365         if (host->version > SDHCI_SPEC_300) {
2366                 printk(KERN_ERR "%s: Unknown controller version (%d). "
2367                         "You may experience problems.\n", mmc_hostname(mmc),
2368                         host->version);
2369         }
2370
2371         caps[0] = (host->quirks & SDHCI_QUIRK_MISSING_CAPS) ? host->caps :
2372                 sdhci_readl(host, SDHCI_CAPABILITIES);
2373
2374         caps[1] = (host->version >= SDHCI_SPEC_300) ?
2375                 sdhci_readl(host, SDHCI_CAPABILITIES_1) : 0;
2376
2377         if (host->quirks & SDHCI_QUIRK_FORCE_DMA)
2378                 host->flags |= SDHCI_USE_SDMA;
2379         else if (!(caps[0] & SDHCI_CAN_DO_SDMA))
2380                 DBG("Controller doesn't have SDMA capability\n");
2381         else
2382                 host->flags |= SDHCI_USE_SDMA;
2383
2384         if ((host->quirks & SDHCI_QUIRK_BROKEN_DMA) &&
2385                 (host->flags & SDHCI_USE_SDMA)) {
2386                 DBG("Disabling DMA as it is marked broken\n");
2387                 host->flags &= ~SDHCI_USE_SDMA;
2388         }
2389
2390         if ((host->version >= SDHCI_SPEC_200) &&
2391                 (caps[0] & SDHCI_CAN_DO_ADMA2))
2392                 host->flags |= SDHCI_USE_ADMA;
2393
2394         if ((host->quirks & SDHCI_QUIRK_BROKEN_ADMA) &&
2395                 (host->flags & SDHCI_USE_ADMA)) {
2396                 DBG("Disabling ADMA as it is marked broken\n");
2397                 host->flags &= ~SDHCI_USE_ADMA;
2398         }
2399
2400         if (host->flags & (SDHCI_USE_SDMA | SDHCI_USE_ADMA)) {
2401                 if (host->ops->enable_dma) {
2402                         if (host->ops->enable_dma(host)) {
2403                                 printk(KERN_WARNING "%s: No suitable DMA "
2404                                         "available. Falling back to PIO.\n",
2405                                         mmc_hostname(mmc));
2406                                 host->flags &=
2407                                         ~(SDHCI_USE_SDMA | SDHCI_USE_ADMA);
2408                         }
2409                 }
2410         }
2411
2412         if (host->flags & SDHCI_USE_ADMA) {
2413                 /*
2414                  * We need to allocate descriptors for all sg entries
2415                  * (128) and potentially one alignment transfer for
2416                  * each of those entries.
2417                  */
2418                 host->adma_desc = kmalloc((128 * 2 + 1) * 4, GFP_KERNEL);
2419                 host->align_buffer = kmalloc(128 * 4, GFP_KERNEL);
2420                 if (!host->adma_desc || !host->align_buffer) {
2421                         kfree(host->adma_desc);
2422                         kfree(host->align_buffer);
2423                         printk(KERN_WARNING "%s: Unable to allocate ADMA "
2424                                 "buffers. Falling back to standard DMA.\n",
2425                                 mmc_hostname(mmc));
2426                         host->flags &= ~SDHCI_USE_ADMA;
2427                 }
2428         }
2429
2430         /*
2431          * If we use DMA, then it's up to the caller to set the DMA
2432          * mask, but PIO does not need the hw shim so we set a new
2433          * mask here in that case.
2434          */
2435         if (!(host->flags & (SDHCI_USE_SDMA | SDHCI_USE_ADMA))) {
2436                 host->dma_mask = DMA_BIT_MASK(64);
2437                 mmc_dev(host->mmc)->dma_mask = &host->dma_mask;
2438         }
2439
2440         if (host->version >= SDHCI_SPEC_300)
2441                 host->max_clk = (caps[0] & SDHCI_CLOCK_V3_BASE_MASK)
2442                         >> SDHCI_CLOCK_BASE_SHIFT;
2443         else
2444                 host->max_clk = (caps[0] & SDHCI_CLOCK_BASE_MASK)
2445                         >> SDHCI_CLOCK_BASE_SHIFT;
2446
2447         host->max_clk *= 1000000;
2448         if (host->max_clk == 0 || host->quirks &
2449                         SDHCI_QUIRK_CAP_CLOCK_BASE_BROKEN) {
2450                 if (!host->ops->get_max_clock) {
2451                         printk(KERN_ERR
2452                                "%s: Hardware doesn't specify base clock "
2453                                "frequency.\n", mmc_hostname(mmc));
2454                         return -ENODEV;
2455                 }
2456                 host->max_clk = host->ops->get_max_clock(host);
2457         }
2458
2459         /*
2460          * In case of Host Controller v3.00, find out whether clock
2461          * multiplier is supported.
2462          */
2463         host->clk_mul = (caps[1] & SDHCI_CLOCK_MUL_MASK) >>
2464                         SDHCI_CLOCK_MUL_SHIFT;
2465
2466         /*
2467          * In case the value in Clock Multiplier is 0, then programmable
2468          * clock mode is not supported, otherwise the actual clock
2469          * multiplier is one more than the value of Clock Multiplier
2470          * in the Capabilities Register.
2471          */
2472         if (host->clk_mul)
2473                 host->clk_mul += 1;
2474
2475         /*
2476          * Set host parameters.
2477          */
2478         mmc->ops = &sdhci_ops;
2479         mmc->f_max = host->max_clk;
2480         if (host->ops->get_min_clock)
2481                 mmc->f_min = host->ops->get_min_clock(host);
2482         else if (host->version >= SDHCI_SPEC_300) {
2483                 if (host->clk_mul) {
2484                         mmc->f_min = (host->max_clk * host->clk_mul) / 1024;
2485                         mmc->f_max = host->max_clk * host->clk_mul;
2486                 } else
2487                         mmc->f_min = host->max_clk / SDHCI_MAX_DIV_SPEC_300;
2488         } else
2489                 mmc->f_min = host->max_clk / SDHCI_MAX_DIV_SPEC_200;
2490
2491         host->timeout_clk =
2492                 (caps[0] & SDHCI_TIMEOUT_CLK_MASK) >> SDHCI_TIMEOUT_CLK_SHIFT;
2493         if (host->timeout_clk == 0) {
2494                 if (host->ops->get_timeout_clock) {
2495                         host->timeout_clk = host->ops->get_timeout_clock(host);
2496                 } else if (!(host->quirks &
2497                                 SDHCI_QUIRK_DATA_TIMEOUT_USES_SDCLK)) {
2498                         printk(KERN_ERR
2499                                "%s: Hardware doesn't specify timeout clock "
2500                                "frequency.\n", mmc_hostname(mmc));
2501                         return -ENODEV;
2502                 }
2503         }
2504         if (caps[0] & SDHCI_TIMEOUT_CLK_UNIT)
2505                 host->timeout_clk *= 1000;
2506
2507         if (host->quirks & SDHCI_QUIRK_DATA_TIMEOUT_USES_SDCLK)
2508                 host->timeout_clk = mmc->f_max / 1000;
2509
2510         mmc->max_discard_to = (1 << 27) / host->timeout_clk;
2511
2512         mmc->caps |= MMC_CAP_SDIO_IRQ | MMC_CAP_ERASE | MMC_CAP_CMD23;
2513
2514         if (host->quirks & SDHCI_QUIRK_MULTIBLOCK_READ_ACMD12)
2515                 host->flags |= SDHCI_AUTO_CMD12;
2516
2517         /* Auto-CMD23 stuff only works in ADMA or PIO. */
2518         if ((host->version >= SDHCI_SPEC_300) &&
2519             ((host->flags & SDHCI_USE_ADMA) ||
2520              !(host->flags & SDHCI_USE_SDMA))) {
2521                 host->flags |= SDHCI_AUTO_CMD23;
2522                 DBG("%s: Auto-CMD23 available\n", mmc_hostname(mmc));
2523         } else {
2524                 DBG("%s: Auto-CMD23 unavailable\n", mmc_hostname(mmc));
2525         }
2526
2527         /*
2528          * A controller may support 8-bit width, but the board itself
2529          * might not have the pins brought out.  Boards that support
2530          * 8-bit width must set "mmc->caps |= MMC_CAP_8_BIT_DATA;" in
2531          * their platform code before calling sdhci_add_host(), and we
2532          * won't assume 8-bit width for hosts without that CAP.
2533          */
2534         if (!(host->quirks & SDHCI_QUIRK_FORCE_1_BIT_DATA))
2535                 mmc->caps |= MMC_CAP_4_BIT_DATA;
2536
2537         if (caps[0] & SDHCI_CAN_DO_HISPD)
2538                 mmc->caps |= MMC_CAP_SD_HIGHSPEED | MMC_CAP_MMC_HIGHSPEED;
2539
2540         if ((host->quirks & SDHCI_QUIRK_BROKEN_CARD_DETECTION) &&
2541             mmc_card_is_removable(mmc))
2542                 mmc->caps |= MMC_CAP_NEEDS_POLL;
2543
2544         /* UHS-I mode(s) supported by the host controller. */
2545         if (host->version >= SDHCI_SPEC_300)
2546                 mmc->caps |= MMC_CAP_UHS_SDR12 | MMC_CAP_UHS_SDR25;
2547
2548         /* SDR104 supports also implies SDR50 support */
2549         if (caps[1] & SDHCI_SUPPORT_SDR104)
2550                 mmc->caps |= MMC_CAP_UHS_SDR104 | MMC_CAP_UHS_SDR50;
2551         else if (caps[1] & SDHCI_SUPPORT_SDR50)
2552                 mmc->caps |= MMC_CAP_UHS_SDR50;
2553
2554         if (caps[1] & SDHCI_SUPPORT_DDR50)
2555                 mmc->caps |= MMC_CAP_UHS_DDR50;
2556
2557         /* Does the host needs tuning for SDR50? */
2558         if (caps[1] & SDHCI_USE_SDR50_TUNING)
2559                 host->flags |= SDHCI_SDR50_NEEDS_TUNING;
2560
2561         /* Driver Type(s) (A, C, D) supported by the host */
2562         if (caps[1] & SDHCI_DRIVER_TYPE_A)
2563                 mmc->caps |= MMC_CAP_DRIVER_TYPE_A;
2564         if (caps[1] & SDHCI_DRIVER_TYPE_C)
2565                 mmc->caps |= MMC_CAP_DRIVER_TYPE_C;
2566         if (caps[1] & SDHCI_DRIVER_TYPE_D)
2567                 mmc->caps |= MMC_CAP_DRIVER_TYPE_D;
2568
2569         /* Initial value for re-tuning timer count */
2570         host->tuning_count = (caps[1] & SDHCI_RETUNING_TIMER_COUNT_MASK) >>
2571                               SDHCI_RETUNING_TIMER_COUNT_SHIFT;
2572
2573         /*
2574          * In case Re-tuning Timer is not disabled, the actual value of
2575          * re-tuning timer will be 2 ^ (n - 1).
2576          */
2577         if (host->tuning_count)
2578                 host->tuning_count = 1 << (host->tuning_count - 1);
2579
2580         /* Re-tuning mode supported by the Host Controller */
2581         host->tuning_mode = (caps[1] & SDHCI_RETUNING_MODE_MASK) >>
2582                              SDHCI_RETUNING_MODE_SHIFT;
2583
2584         ocr_avail = 0;
2585         /*
2586          * According to SD Host Controller spec v3.00, if the Host System
2587          * can afford more than 150mA, Host Driver should set XPC to 1. Also
2588          * the value is meaningful only if Voltage Support in the Capabilities
2589          * register is set. The actual current value is 4 times the register
2590          * value.
2591          */
2592         max_current_caps = sdhci_readl(host, SDHCI_MAX_CURRENT);
2593
2594         if (caps[0] & SDHCI_CAN_VDD_330) {
2595                 int max_current_330;
2596
2597                 ocr_avail |= MMC_VDD_32_33 | MMC_VDD_33_34;
2598
2599                 max_current_330 = ((max_current_caps &
2600                                    SDHCI_MAX_CURRENT_330_MASK) >>
2601                                    SDHCI_MAX_CURRENT_330_SHIFT) *
2602                                    SDHCI_MAX_CURRENT_MULTIPLIER;
2603
2604                 if (max_current_330 > 150)
2605                         mmc->caps |= MMC_CAP_SET_XPC_330;
2606         }
2607         if (caps[0] & SDHCI_CAN_VDD_300) {
2608                 int max_current_300;
2609
2610                 ocr_avail |= MMC_VDD_29_30 | MMC_VDD_30_31;
2611
2612                 max_current_300 = ((max_current_caps &
2613                                    SDHCI_MAX_CURRENT_300_MASK) >>
2614                                    SDHCI_MAX_CURRENT_300_SHIFT) *
2615                                    SDHCI_MAX_CURRENT_MULTIPLIER;
2616
2617                 if (max_current_300 > 150)
2618                         mmc->caps |= MMC_CAP_SET_XPC_300;
2619         }
2620         if (caps[0] & SDHCI_CAN_VDD_180) {
2621                 int max_current_180;
2622
2623                 ocr_avail |= MMC_VDD_165_195;
2624
2625                 max_current_180 = ((max_current_caps &
2626                                    SDHCI_MAX_CURRENT_180_MASK) >>
2627                                    SDHCI_MAX_CURRENT_180_SHIFT) *
2628                                    SDHCI_MAX_CURRENT_MULTIPLIER;
2629
2630                 if (max_current_180 > 150)
2631                         mmc->caps |= MMC_CAP_SET_XPC_180;
2632
2633                 /* Maximum current capabilities of the host at 1.8V */
2634                 if (max_current_180 >= 800)
2635                         mmc->caps |= MMC_CAP_MAX_CURRENT_800;
2636                 else if (max_current_180 >= 600)
2637                         mmc->caps |= MMC_CAP_MAX_CURRENT_600;
2638                 else if (max_current_180 >= 400)
2639                         mmc->caps |= MMC_CAP_MAX_CURRENT_400;
2640                 else
2641                         mmc->caps |= MMC_CAP_MAX_CURRENT_200;
2642         }
2643
2644         mmc->ocr_avail = ocr_avail;
2645         mmc->ocr_avail_sdio = ocr_avail;
2646         if (host->ocr_avail_sdio)
2647                 mmc->ocr_avail_sdio &= host->ocr_avail_sdio;
2648         mmc->ocr_avail_sd = ocr_avail;
2649         if (host->ocr_avail_sd)
2650                 mmc->ocr_avail_sd &= host->ocr_avail_sd;
2651         else /* normal SD controllers don't support 1.8V */
2652                 mmc->ocr_avail_sd &= ~MMC_VDD_165_195;
2653         mmc->ocr_avail_mmc = ocr_avail;
2654         if (host->ocr_avail_mmc)
2655                 mmc->ocr_avail_mmc &= host->ocr_avail_mmc;
2656
2657         if (mmc->ocr_avail == 0) {
2658                 printk(KERN_ERR "%s: Hardware doesn't report any "
2659                         "support voltages.\n", mmc_hostname(mmc));
2660                 return -ENODEV;
2661         }
2662
2663         spin_lock_init(&host->lock);
2664
2665         /*
2666          * Maximum number of segments. Depends on if the hardware
2667          * can do scatter/gather or not.
2668          */
2669         if (host->flags & SDHCI_USE_ADMA)
2670                 mmc->max_segs = 128;
2671         else if (host->flags & SDHCI_USE_SDMA)
2672                 mmc->max_segs = 1;
2673         else /* PIO */
2674                 mmc->max_segs = 128;
2675
2676         /*
2677          * Maximum number of sectors in one transfer. Limited by DMA boundary
2678          * size (512KiB).
2679          */
2680         mmc->max_req_size = 524288;
2681
2682         /*
2683          * Maximum segment size. Could be one segment with the maximum number
2684          * of bytes. When doing hardware scatter/gather, each entry cannot
2685          * be larger than 64 KiB though.
2686          */
2687         if (host->flags & SDHCI_USE_ADMA) {
2688                 if (host->quirks & SDHCI_QUIRK_BROKEN_ADMA_ZEROLEN_DESC)
2689                         mmc->max_seg_size = 65535;
2690                 else
2691                         mmc->max_seg_size = 65536;
2692         } else {
2693                 mmc->max_seg_size = mmc->max_req_size;
2694         }
2695
2696         /*
2697          * Maximum block size. This varies from controller to controller and
2698          * is specified in the capabilities register.
2699          */
2700         if (host->quirks & SDHCI_QUIRK_FORCE_BLK_SZ_2048) {
2701                 mmc->max_blk_size = 2;
2702         } else {
2703                 mmc->max_blk_size = (caps[0] & SDHCI_MAX_BLOCK_MASK) >>
2704                                 SDHCI_MAX_BLOCK_SHIFT;
2705                 if (mmc->max_blk_size >= 3) {
2706                         printk(KERN_WARNING "%s: Invalid maximum block size, "
2707                                 "assuming 512 bytes\n", mmc_hostname(mmc));
2708                         mmc->max_blk_size = 0;
2709                 }
2710         }
2711
2712         mmc->max_blk_size = 512 << mmc->max_blk_size;
2713
2714         /*
2715          * Maximum block count.
2716          */
2717         mmc->max_blk_count = (host->quirks & SDHCI_QUIRK_NO_MULTIBLOCK) ? 1 : 65535;
2718
2719         /*
2720          * Init tasklets.
2721          */
2722         tasklet_init(&host->card_tasklet,
2723                 sdhci_tasklet_card, (unsigned long)host);
2724         tasklet_init(&host->finish_tasklet,
2725                 sdhci_tasklet_finish, (unsigned long)host);
2726
2727         setup_timer(&host->timer, sdhci_timeout_timer, (unsigned long)host);
2728
2729         if (host->version >= SDHCI_SPEC_300) {
2730                 init_waitqueue_head(&host->buf_ready_int);
2731
2732                 /* Initialize re-tuning timer */
2733                 init_timer(&host->tuning_timer);
2734                 host->tuning_timer.data = (unsigned long)host;
2735                 host->tuning_timer.function = sdhci_tuning_timer;
2736         }
2737
2738         ret = request_irq(host->irq, sdhci_irq, IRQF_SHARED,
2739                 mmc_hostname(mmc), host);
2740         if (ret)
2741                 goto untasklet;
2742
2743         host->vmmc = regulator_get(mmc_dev(mmc), "vmmc");
2744         if (IS_ERR(host->vmmc)) {
2745                 printk(KERN_INFO "%s: no vmmc regulator found\n", mmc_hostname(mmc));
2746                 host->vmmc = NULL;
2747         } else {
2748                 regulator_enable(host->vmmc);
2749         }
2750
2751         sdhci_init(host, 0);
2752
2753 #ifdef CONFIG_MMC_DEBUG
2754         sdhci_dumpregs(host);
2755 #endif
2756
2757 #ifdef SDHCI_USE_LEDS_CLASS
2758         snprintf(host->led_name, sizeof(host->led_name),
2759                 "%s::", mmc_hostname(mmc));
2760         host->led.name = host->led_name;
2761         host->led.brightness = LED_OFF;
2762         host->led.default_trigger = mmc_hostname(mmc);
2763         host->led.brightness_set = sdhci_led_control;
2764
2765         ret = led_classdev_register(mmc_dev(mmc), &host->led);
2766         if (ret)
2767                 goto reset;
2768 #endif
2769
2770         mmiowb();
2771
2772         mmc_add_host(mmc);
2773
2774         printk(KERN_INFO "%s: SDHCI controller on %s [%s] using %s\n",
2775                 mmc_hostname(mmc), host->hw_name, dev_name(mmc_dev(mmc)),
2776                 (host->flags & SDHCI_USE_ADMA) ? "ADMA" :
2777                 (host->flags & SDHCI_USE_SDMA) ? "DMA" : "PIO");
2778
2779         sdhci_enable_card_detection(host);
2780
2781         return 0;
2782
2783 #ifdef SDHCI_USE_LEDS_CLASS
2784 reset:
2785         sdhci_reset(host, SDHCI_RESET_ALL);
2786         free_irq(host->irq, host);
2787 #endif
2788 untasklet:
2789         tasklet_kill(&host->card_tasklet);
2790         tasklet_kill(&host->finish_tasklet);
2791
2792         return ret;
2793 }
2794
2795 EXPORT_SYMBOL_GPL(sdhci_add_host);
2796
2797 void sdhci_remove_host(struct sdhci_host *host, int dead)
2798 {
2799         unsigned long flags;
2800
2801         if (dead) {
2802                 spin_lock_irqsave(&host->lock, flags);
2803
2804                 host->flags |= SDHCI_DEVICE_DEAD;
2805
2806                 if (host->mrq) {
2807                         printk(KERN_ERR "%s: Controller removed during "
2808                                 " transfer!\n", mmc_hostname(host->mmc));
2809
2810                         host->mrq->cmd->error = -ENOMEDIUM;
2811                         tasklet_schedule(&host->finish_tasklet);
2812                 }
2813
2814                 spin_unlock_irqrestore(&host->lock, flags);
2815         }
2816
2817         sdhci_disable_card_detection(host);
2818
2819         mmc_remove_host(host->mmc);
2820
2821 #ifdef SDHCI_USE_LEDS_CLASS
2822         led_classdev_unregister(&host->led);
2823 #endif
2824
2825         if (!dead)
2826                 sdhci_reset(host, SDHCI_RESET_ALL);
2827
2828         free_irq(host->irq, host);
2829
2830         del_timer_sync(&host->timer);
2831         if (host->version >= SDHCI_SPEC_300)
2832                 del_timer_sync(&host->tuning_timer);
2833
2834         tasklet_kill(&host->card_tasklet);
2835         tasklet_kill(&host->finish_tasklet);
2836
2837         if (host->vmmc) {
2838                 regulator_disable(host->vmmc);
2839                 regulator_put(host->vmmc);
2840         }
2841
2842         kfree(host->adma_desc);
2843         kfree(host->align_buffer);
2844
2845         host->adma_desc = NULL;
2846         host->align_buffer = NULL;
2847 }
2848
2849 EXPORT_SYMBOL_GPL(sdhci_remove_host);
2850
2851 void sdhci_free_host(struct sdhci_host *host)
2852 {
2853         mmc_free_host(host->mmc);
2854 }
2855
2856 EXPORT_SYMBOL_GPL(sdhci_free_host);
2857
2858 /*****************************************************************************\
2859  *                                                                           *
2860  * Driver init/exit                                                          *
2861  *                                                                           *
2862 \*****************************************************************************/
2863
2864 static int __init sdhci_drv_init(void)
2865 {
2866         printk(KERN_INFO DRIVER_NAME
2867                 ": Secure Digital Host Controller Interface driver\n");
2868         printk(KERN_INFO DRIVER_NAME ": Copyright(c) Pierre Ossman\n");
2869
2870         return 0;
2871 }
2872
2873 static void __exit sdhci_drv_exit(void)
2874 {
2875 }
2876
2877 module_init(sdhci_drv_init);
2878 module_exit(sdhci_drv_exit);
2879
2880 module_param(debug_quirks, uint, 0444);
2881
2882 MODULE_AUTHOR("Pierre Ossman <pierre@ossman.eu>");
2883 MODULE_DESCRIPTION("Secure Digital Host Controller Interface core driver");
2884 MODULE_LICENSE("GPL");
2885
2886 MODULE_PARM_DESC(debug_quirks, "Force certain quirks.");