2 * Copyright 2005 Nicolai Haehnle et al.
3 * Copyright 2008 Advanced Micro Devices, Inc.
4 * Copyright 2009 Jerome Glisse.
6 * Permission is hereby granted, free of charge, to any person obtaining a
7 * copy of this software and associated documentation files (the "Software"),
8 * to deal in the Software without restriction, including without limitation
9 * the rights to use, copy, modify, merge, publish, distribute, sublicense,
10 * and/or sell copies of the Software, and to permit persons to whom the
11 * Software is furnished to do so, subject to the following conditions:
13 * The above copyright notice and this permission notice shall be included in
14 * all copies or substantial portions of the Software.
16 * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR
17 * IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY,
18 * FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL
19 * THE COPYRIGHT HOLDER(S) OR AUTHOR(S) BE LIABLE FOR ANY CLAIM, DAMAGES OR
20 * OTHER LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE,
21 * ARISING FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
22 * OTHER DEALINGS IN THE SOFTWARE.
24 * Authors: Nicolai Haehnle
30 #define R300_SURF_TILE_MACRO (1<<16)
31 #define R300_SURF_TILE_MICRO (2<<16)
32 #define R300_SURF_TILE_BOTH (3<<16)
35 #define R300_MC_INIT_MISC_LAT_TIMER 0x180
36 # define R300_MC_MISC__MC_CPR_INIT_LAT_SHIFT 0
37 # define R300_MC_MISC__MC_VF_INIT_LAT_SHIFT 4
38 # define R300_MC_MISC__MC_DISP0R_INIT_LAT_SHIFT 8
39 # define R300_MC_MISC__MC_DISP1R_INIT_LAT_SHIFT 12
40 # define R300_MC_MISC__MC_FIXED_INIT_LAT_SHIFT 16
41 # define R300_MC_MISC__MC_E2R_INIT_LAT_SHIFT 20
42 # define R300_MC_MISC__MC_SAME_PAGE_PRIO_SHIFT 24
43 # define R300_MC_MISC__MC_GLOBW_INIT_LAT_SHIFT 28
45 #define R300_MC_INIT_GFX_LAT_TIMER 0x154
46 # define R300_MC_MISC__MC_G3D0R_INIT_LAT_SHIFT 0
47 # define R300_MC_MISC__MC_G3D1R_INIT_LAT_SHIFT 4
48 # define R300_MC_MISC__MC_G3D2R_INIT_LAT_SHIFT 8
49 # define R300_MC_MISC__MC_G3D3R_INIT_LAT_SHIFT 12
50 # define R300_MC_MISC__MC_TX0R_INIT_LAT_SHIFT 16
51 # define R300_MC_MISC__MC_TX1R_INIT_LAT_SHIFT 20
52 # define R300_MC_MISC__MC_GLOBR_INIT_LAT_SHIFT 24
53 # define R300_MC_MISC__MC_GLOBW_FULL_LAT_SHIFT 28
56 * This file contains registers and constants for the R300. They have been
57 * found mostly by examining command buffers captured using glxtest, as well
58 * as by extrapolating some known registers and constants from the R200.
59 * I am fairly certain that they are correct unless stated otherwise
63 #define R300_SE_VPORT_XSCALE 0x1D98
64 #define R300_SE_VPORT_XOFFSET 0x1D9C
65 #define R300_SE_VPORT_YSCALE 0x1DA0
66 #define R300_SE_VPORT_YOFFSET 0x1DA4
67 #define R300_SE_VPORT_ZSCALE 0x1DA8
68 #define R300_SE_VPORT_ZOFFSET 0x1DAC
72 * Vertex Array Processing (VAP) Control
73 * Stolen from r200 code from Christoph Brill (It's a guess!)
75 #define R300_VAP_CNTL 0x2080
77 /* This register is written directly and also starts data section
78 * in many 3d CP_PACKET3's
80 #define R300_VAP_VF_CNTL 0x2084
81 # define R300_VAP_VF_CNTL__PRIM_TYPE__SHIFT 0
82 # define R300_VAP_VF_CNTL__PRIM_NONE (0<<0)
83 # define R300_VAP_VF_CNTL__PRIM_POINTS (1<<0)
84 # define R300_VAP_VF_CNTL__PRIM_LINES (2<<0)
85 # define R300_VAP_VF_CNTL__PRIM_LINE_STRIP (3<<0)
86 # define R300_VAP_VF_CNTL__PRIM_TRIANGLES (4<<0)
87 # define R300_VAP_VF_CNTL__PRIM_TRIANGLE_FAN (5<<0)
88 # define R300_VAP_VF_CNTL__PRIM_TRIANGLE_STRIP (6<<0)
89 # define R300_VAP_VF_CNTL__PRIM_LINE_LOOP (12<<0)
90 # define R300_VAP_VF_CNTL__PRIM_QUADS (13<<0)
91 # define R300_VAP_VF_CNTL__PRIM_QUAD_STRIP (14<<0)
92 # define R300_VAP_VF_CNTL__PRIM_POLYGON (15<<0)
94 # define R300_VAP_VF_CNTL__PRIM_WALK__SHIFT 4
95 /* State based - direct writes to registers trigger vertex
97 # define R300_VAP_VF_CNTL__PRIM_WALK_STATE_BASED (0<<4)
98 # define R300_VAP_VF_CNTL__PRIM_WALK_INDICES (1<<4)
99 # define R300_VAP_VF_CNTL__PRIM_WALK_VERTEX_LIST (2<<4)
100 # define R300_VAP_VF_CNTL__PRIM_WALK_VERTEX_EMBEDDED (3<<4)
102 /* I don't think I saw these three used.. */
103 # define R300_VAP_VF_CNTL__COLOR_ORDER__SHIFT 6
104 # define R300_VAP_VF_CNTL__TCL_OUTPUT_CTL_ENA__SHIFT 9
105 # define R300_VAP_VF_CNTL__PROG_STREAM_ENA__SHIFT 10
107 /* index size - when not set the indices are assumed to be 16 bit */
108 # define R300_VAP_VF_CNTL__INDEX_SIZE_32bit (1<<11)
109 /* number of vertices */
110 # define R300_VAP_VF_CNTL__NUM_VERTICES__SHIFT 16
112 /* BEGIN: Wild guesses */
113 #define R300_VAP_OUTPUT_VTX_FMT_0 0x2090
114 # define R300_VAP_OUTPUT_VTX_FMT_0__POS_PRESENT (1<<0)
115 # define R300_VAP_OUTPUT_VTX_FMT_0__COLOR_PRESENT (1<<1)
116 # define R300_VAP_OUTPUT_VTX_FMT_0__COLOR_1_PRESENT (1<<2) /* GUESS */
117 # define R300_VAP_OUTPUT_VTX_FMT_0__COLOR_2_PRESENT (1<<3) /* GUESS */
118 # define R300_VAP_OUTPUT_VTX_FMT_0__COLOR_3_PRESENT (1<<4) /* GUESS */
119 # define R300_VAP_OUTPUT_VTX_FMT_0__PT_SIZE_PRESENT (1<<16) /* GUESS */
121 #define R300_VAP_OUTPUT_VTX_FMT_1 0x2094
122 /* each of the following is 3 bits wide, specifies number
124 # define R300_VAP_OUTPUT_VTX_FMT_1__TEX_0_COMP_CNT_SHIFT 0
125 # define R300_VAP_OUTPUT_VTX_FMT_1__TEX_1_COMP_CNT_SHIFT 3
126 # define R300_VAP_OUTPUT_VTX_FMT_1__TEX_2_COMP_CNT_SHIFT 6
127 # define R300_VAP_OUTPUT_VTX_FMT_1__TEX_3_COMP_CNT_SHIFT 9
128 # define R300_VAP_OUTPUT_VTX_FMT_1__TEX_4_COMP_CNT_SHIFT 12
129 # define R300_VAP_OUTPUT_VTX_FMT_1__TEX_5_COMP_CNT_SHIFT 15
130 # define R300_VAP_OUTPUT_VTX_FMT_1__TEX_6_COMP_CNT_SHIFT 18
131 # define R300_VAP_OUTPUT_VTX_FMT_1__TEX_7_COMP_CNT_SHIFT 21
132 /* END: Wild guesses */
134 #define R300_SE_VTE_CNTL 0x20b0
135 # define R300_VPORT_X_SCALE_ENA 0x00000001
136 # define R300_VPORT_X_OFFSET_ENA 0x00000002
137 # define R300_VPORT_Y_SCALE_ENA 0x00000004
138 # define R300_VPORT_Y_OFFSET_ENA 0x00000008
139 # define R300_VPORT_Z_SCALE_ENA 0x00000010
140 # define R300_VPORT_Z_OFFSET_ENA 0x00000020
141 # define R300_VTX_XY_FMT 0x00000100
142 # define R300_VTX_Z_FMT 0x00000200
143 # define R300_VTX_W0_FMT 0x00000400
144 # define R300_VTX_W0_NORMALIZE 0x00000800
145 # define R300_VTX_ST_DENORMALIZED 0x00001000
147 /* BEGIN: Vertex data assembly - lots of uncertainties */
151 #define R300_VAP_CNTL_STATUS 0x2140
152 # define R300_VC_NO_SWAP (0 << 0)
153 # define R300_VC_16BIT_SWAP (1 << 0)
154 # define R300_VC_32BIT_SWAP (2 << 0)
155 # define R300_VAP_TCL_BYPASS (1 << 8)
159 /* Where do we get our vertex data?
161 * Vertex data either comes either from immediate mode registers or from
163 * There appears to be no mixed mode (though we can force the pitch of
164 * vertex arrays to 0, effectively reusing the same element over and over
167 * Immediate mode is controlled by the INPUT_CNTL registers. I am not sure
168 * if these registers influence vertex array processing.
170 * Vertex arrays are controlled via the 3D_LOAD_VBPNTR packet3.
172 * In both cases, vertex attributes are then passed through INPUT_ROUTE.
174 * Beginning with INPUT_ROUTE_0_0 is a list of WORDs that route vertex data
175 * into the vertex processor's input registers.
176 * The first word routes the first input, the second word the second, etc.
177 * The corresponding input is routed into the register with the given index.
178 * The list is ended by a word with INPUT_ROUTE_END set.
180 * Always set COMPONENTS_4 in immediate mode.
183 #define R300_VAP_INPUT_ROUTE_0_0 0x2150
184 # define R300_INPUT_ROUTE_COMPONENTS_1 (0 << 0)
185 # define R300_INPUT_ROUTE_COMPONENTS_2 (1 << 0)
186 # define R300_INPUT_ROUTE_COMPONENTS_3 (2 << 0)
187 # define R300_INPUT_ROUTE_COMPONENTS_4 (3 << 0)
188 # define R300_INPUT_ROUTE_COMPONENTS_RGBA (4 << 0) /* GUESS */
189 # define R300_VAP_INPUT_ROUTE_IDX_SHIFT 8
190 # define R300_VAP_INPUT_ROUTE_IDX_MASK (31 << 8) /* GUESS */
191 # define R300_VAP_INPUT_ROUTE_END (1 << 13)
192 # define R300_INPUT_ROUTE_IMMEDIATE_MODE (0 << 14) /* GUESS */
193 # define R300_INPUT_ROUTE_FLOAT (1 << 14) /* GUESS */
194 # define R300_INPUT_ROUTE_UNSIGNED_BYTE (2 << 14) /* GUESS */
195 # define R300_INPUT_ROUTE_FLOAT_COLOR (3 << 14) /* GUESS */
196 #define R300_VAP_INPUT_ROUTE_0_1 0x2154
197 #define R300_VAP_INPUT_ROUTE_0_2 0x2158
198 #define R300_VAP_INPUT_ROUTE_0_3 0x215C
199 #define R300_VAP_INPUT_ROUTE_0_4 0x2160
200 #define R300_VAP_INPUT_ROUTE_0_5 0x2164
201 #define R300_VAP_INPUT_ROUTE_0_6 0x2168
202 #define R300_VAP_INPUT_ROUTE_0_7 0x216C
207 * - always set up to produce at least two attributes:
208 * if vertex program uses only position, fglrx will set normal, too
209 * - INPUT_CNTL_0_COLOR and INPUT_CNTL_COLOR bits are always equal.
211 #define R300_VAP_INPUT_CNTL_0 0x2180
212 # define R300_INPUT_CNTL_0_COLOR 0x00000001
213 #define R300_VAP_INPUT_CNTL_1 0x2184
214 # define R300_INPUT_CNTL_POS 0x00000001
215 # define R300_INPUT_CNTL_NORMAL 0x00000002
216 # define R300_INPUT_CNTL_COLOR 0x00000004
217 # define R300_INPUT_CNTL_TC0 0x00000400
218 # define R300_INPUT_CNTL_TC1 0x00000800
219 # define R300_INPUT_CNTL_TC2 0x00001000 /* GUESS */
220 # define R300_INPUT_CNTL_TC3 0x00002000 /* GUESS */
221 # define R300_INPUT_CNTL_TC4 0x00004000 /* GUESS */
222 # define R300_INPUT_CNTL_TC5 0x00008000 /* GUESS */
223 # define R300_INPUT_CNTL_TC6 0x00010000 /* GUESS */
224 # define R300_INPUT_CNTL_TC7 0x00020000 /* GUESS */
228 /* Words parallel to INPUT_ROUTE_0; All words that are active in INPUT_ROUTE_0
229 * are set to a swizzling bit pattern, other words are 0.
231 * In immediate mode, the pattern is always set to xyzw. In vertex array
232 * mode, the swizzling pattern is e.g. used to set zw components in texture
233 * coordinates with only tweo components.
235 #define R300_VAP_INPUT_ROUTE_1_0 0x21E0
236 # define R300_INPUT_ROUTE_SELECT_X 0
237 # define R300_INPUT_ROUTE_SELECT_Y 1
238 # define R300_INPUT_ROUTE_SELECT_Z 2
239 # define R300_INPUT_ROUTE_SELECT_W 3
240 # define R300_INPUT_ROUTE_SELECT_ZERO 4
241 # define R300_INPUT_ROUTE_SELECT_ONE 5
242 # define R300_INPUT_ROUTE_SELECT_MASK 7
243 # define R300_INPUT_ROUTE_X_SHIFT 0
244 # define R300_INPUT_ROUTE_Y_SHIFT 3
245 # define R300_INPUT_ROUTE_Z_SHIFT 6
246 # define R300_INPUT_ROUTE_W_SHIFT 9
247 # define R300_INPUT_ROUTE_ENABLE (15 << 12)
248 #define R300_VAP_INPUT_ROUTE_1_1 0x21E4
249 #define R300_VAP_INPUT_ROUTE_1_2 0x21E8
250 #define R300_VAP_INPUT_ROUTE_1_3 0x21EC
251 #define R300_VAP_INPUT_ROUTE_1_4 0x21F0
252 #define R300_VAP_INPUT_ROUTE_1_5 0x21F4
253 #define R300_VAP_INPUT_ROUTE_1_6 0x21F8
254 #define R300_VAP_INPUT_ROUTE_1_7 0x21FC
256 /* END: Vertex data assembly */
260 /* BEGIN: Upload vertex program and data */
263 * The programmable vertex shader unit has a memory bank of unknown size
264 * that can be written to in 16 byte units by writing the address into
265 * UPLOAD_ADDRESS, followed by data in UPLOAD_DATA (multiples of 4 DWORDs).
267 * Pointers into the memory bank are always in multiples of 16 bytes.
269 * The memory bank is divided into areas with fixed meaning.
271 * Starting at address UPLOAD_PROGRAM: Vertex program instructions.
272 * Native limits reported by drivers from ATI suggest size 256 (i.e. 4KB),
273 * whereas the difference between known addresses suggests size 512.
275 * Starting at address UPLOAD_PARAMETERS: Vertex program parameters.
276 * Native reported limits and the VPI layout suggest size 256, whereas
277 * difference between known addresses suggests size 512.
279 * At address UPLOAD_POINTSIZE is a vector (0, 0, ps, 0), where ps is the
280 * floating point pointsize. The exact purpose of this state is uncertain,
281 * as there is also the R300_RE_POINTSIZE register.
283 * Multiple vertex programs and parameter sets can be loaded at once,
284 * which could explain the size discrepancy.
286 #define R300_VAP_PVS_UPLOAD_ADDRESS 0x2200
287 # define R300_PVS_UPLOAD_PROGRAM 0x00000000
288 # define R300_PVS_UPLOAD_PARAMETERS 0x00000200
289 # define R300_PVS_UPLOAD_POINTSIZE 0x00000406
293 #define R300_VAP_PVS_UPLOAD_DATA 0x2208
295 /* END: Upload vertex program and data */
299 /* I do not know the purpose of this register. However, I do know that
300 * it is set to 221C_CLEAR for clear operations and to 221C_NORMAL
301 * for normal rendering.
303 #define R300_VAP_UNKNOWN_221C 0x221C
304 # define R300_221C_NORMAL 0x00000000
305 # define R300_221C_CLEAR 0x0001C000
307 /* These seem to be per-pixel and per-vertex X and Y clipping planes. The first
308 * plane is per-pixel and the second plane is per-vertex.
310 * This was determined by experimentation alone but I believe it is correct.
312 * These registers are called X_QUAD0_1_FL to X_QUAD0_4_FL by glxtest.
314 #define R300_VAP_CLIP_X_0 0x2220
315 #define R300_VAP_CLIP_X_1 0x2224
316 #define R300_VAP_CLIP_Y_0 0x2228
317 #define R300_VAP_CLIP_Y_1 0x2230
321 /* Sometimes, END_OF_PKT and 0x2284=0 are the only commands sent between
322 * rendering commands and overwriting vertex program parameters.
323 * Therefore, I suspect writing zero to 0x2284 synchronizes the engine and
324 * avoids bugs caused by still running shaders reading bad data from memory.
326 #define R300_VAP_PVS_STATE_FLUSH_REG 0x2284
328 /* Absolutely no clue what this register is about. */
329 #define R300_VAP_UNKNOWN_2288 0x2288
330 # define R300_2288_R300 0x00750000 /* -- nh */
331 # define R300_2288_RV350 0x0000FFFF /* -- Vladimir */
335 /* Addresses are relative to the vertex program instruction area of the
336 * memory bank. PROGRAM_END points to the last instruction of the active
339 * The meaning of the two UNKNOWN fields is obviously not known. However,
340 * experiments so far have shown that both *must* point to an instruction
341 * inside the vertex program, otherwise the GPU locks up.
343 * fglrx usually sets CNTL_3_UNKNOWN to the end of the program and
344 * R300_PVS_CNTL_1_POS_END_SHIFT points to instruction where last write to
345 * position takes place.
347 * Most likely this is used to ignore rest of the program in cases
348 * where group of verts arent visible. For some reason this "section"
349 * is sometimes accepted other instruction that have no relationship with
350 * position calculations.
352 #define R300_VAP_PVS_CNTL_1 0x22D0
353 # define R300_PVS_CNTL_1_PROGRAM_START_SHIFT 0
354 # define R300_PVS_CNTL_1_POS_END_SHIFT 10
355 # define R300_PVS_CNTL_1_PROGRAM_END_SHIFT 20
356 /* Addresses are relative the the vertex program parameters area. */
357 #define R300_VAP_PVS_CNTL_2 0x22D4
358 # define R300_PVS_CNTL_2_PARAM_OFFSET_SHIFT 0
359 # define R300_PVS_CNTL_2_PARAM_COUNT_SHIFT 16
360 #define R300_VAP_PVS_CNTL_3 0x22D8
361 # define R300_PVS_CNTL_3_PROGRAM_UNKNOWN_SHIFT 10
362 # define R300_PVS_CNTL_3_PROGRAM_UNKNOWN2_SHIFT 0
364 /* The entire range from 0x2300 to 0x2AC inclusive seems to be used for
367 #define R300_VAP_VTX_COLOR_R 0x2464
368 #define R300_VAP_VTX_COLOR_G 0x2468
369 #define R300_VAP_VTX_COLOR_B 0x246C
370 #define R300_VAP_VTX_POS_0_X_1 0x2490 /* used for glVertex2*() */
371 #define R300_VAP_VTX_POS_0_Y_1 0x2494
372 #define R300_VAP_VTX_COLOR_PKD 0x249C /* RGBA */
373 #define R300_VAP_VTX_POS_0_X_2 0x24A0 /* used for glVertex3*() */
374 #define R300_VAP_VTX_POS_0_Y_2 0x24A4
375 #define R300_VAP_VTX_POS_0_Z_2 0x24A8
376 /* write 0 to indicate end of packet? */
377 #define R300_VAP_VTX_END_OF_PKT 0x24AC
381 /* These are values from r300_reg/r300_reg.h - they are known to be correct
382 * and are here so we can use one register file instead of several
385 #define R300_GB_VAP_RASTER_VTX_FMT_0 0x4000
386 # define R300_GB_VAP_RASTER_VTX_FMT_0__POS_PRESENT (1<<0)
387 # define R300_GB_VAP_RASTER_VTX_FMT_0__COLOR_0_PRESENT (1<<1)
388 # define R300_GB_VAP_RASTER_VTX_FMT_0__COLOR_1_PRESENT (1<<2)
389 # define R300_GB_VAP_RASTER_VTX_FMT_0__COLOR_2_PRESENT (1<<3)
390 # define R300_GB_VAP_RASTER_VTX_FMT_0__COLOR_3_PRESENT (1<<4)
391 # define R300_GB_VAP_RASTER_VTX_FMT_0__COLOR_SPACE (0xf<<5)
392 # define R300_GB_VAP_RASTER_VTX_FMT_0__PT_SIZE_PRESENT (0x1<<16)
394 #define R300_GB_VAP_RASTER_VTX_FMT_1 0x4004
395 /* each of the following is 3 bits wide, specifies number
397 # define R300_GB_VAP_RASTER_VTX_FMT_1__TEX_0_COMP_CNT_SHIFT 0
398 # define R300_GB_VAP_RASTER_VTX_FMT_1__TEX_1_COMP_CNT_SHIFT 3
399 # define R300_GB_VAP_RASTER_VTX_FMT_1__TEX_2_COMP_CNT_SHIFT 6
400 # define R300_GB_VAP_RASTER_VTX_FMT_1__TEX_3_COMP_CNT_SHIFT 9
401 # define R300_GB_VAP_RASTER_VTX_FMT_1__TEX_4_COMP_CNT_SHIFT 12
402 # define R300_GB_VAP_RASTER_VTX_FMT_1__TEX_5_COMP_CNT_SHIFT 15
403 # define R300_GB_VAP_RASTER_VTX_FMT_1__TEX_6_COMP_CNT_SHIFT 18
404 # define R300_GB_VAP_RASTER_VTX_FMT_1__TEX_7_COMP_CNT_SHIFT 21
406 /* UNK30 seems to enables point to quad transformation on textures
407 * (or something closely related to that).
408 * This bit is rather fatal at the time being due to lackings at pixel
411 #define R300_GB_ENABLE 0x4008
412 # define R300_GB_POINT_STUFF_ENABLE (1<<0)
413 # define R300_GB_LINE_STUFF_ENABLE (1<<1)
414 # define R300_GB_TRIANGLE_STUFF_ENABLE (1<<2)
415 # define R300_GB_STENCIL_AUTO_ENABLE (1<<4)
416 # define R300_GB_UNK31 (1<<31)
417 /* each of the following is 2 bits wide */
418 #define R300_GB_TEX_REPLICATE 0
419 #define R300_GB_TEX_ST 1
420 #define R300_GB_TEX_STR 2
421 # define R300_GB_TEX0_SOURCE_SHIFT 16
422 # define R300_GB_TEX1_SOURCE_SHIFT 18
423 # define R300_GB_TEX2_SOURCE_SHIFT 20
424 # define R300_GB_TEX3_SOURCE_SHIFT 22
425 # define R300_GB_TEX4_SOURCE_SHIFT 24
426 # define R300_GB_TEX5_SOURCE_SHIFT 26
427 # define R300_GB_TEX6_SOURCE_SHIFT 28
428 # define R300_GB_TEX7_SOURCE_SHIFT 30
430 /* MSPOS - positions for multisample antialiasing (?) */
431 #define R300_GB_MSPOS0 0x4010
432 /* shifts - each of the fields is 4 bits */
433 # define R300_GB_MSPOS0__MS_X0_SHIFT 0
434 # define R300_GB_MSPOS0__MS_Y0_SHIFT 4
435 # define R300_GB_MSPOS0__MS_X1_SHIFT 8
436 # define R300_GB_MSPOS0__MS_Y1_SHIFT 12
437 # define R300_GB_MSPOS0__MS_X2_SHIFT 16
438 # define R300_GB_MSPOS0__MS_Y2_SHIFT 20
439 # define R300_GB_MSPOS0__MSBD0_Y 24
440 # define R300_GB_MSPOS0__MSBD0_X 28
442 #define R300_GB_MSPOS1 0x4014
443 # define R300_GB_MSPOS1__MS_X3_SHIFT 0
444 # define R300_GB_MSPOS1__MS_Y3_SHIFT 4
445 # define R300_GB_MSPOS1__MS_X4_SHIFT 8
446 # define R300_GB_MSPOS1__MS_Y4_SHIFT 12
447 # define R300_GB_MSPOS1__MS_X5_SHIFT 16
448 # define R300_GB_MSPOS1__MS_Y5_SHIFT 20
449 # define R300_GB_MSPOS1__MSBD1 24
452 #define R300_GB_TILE_CONFIG 0x4018
453 # define R300_GB_TILE_ENABLE (1<<0)
454 # define R300_GB_TILE_PIPE_COUNT_RV300 0
455 # define R300_GB_TILE_PIPE_COUNT_R300 (3<<1)
456 # define R300_GB_TILE_PIPE_COUNT_R420 (7<<1)
457 # define R300_GB_TILE_PIPE_COUNT_RV410 (3<<1)
458 # define R300_GB_TILE_SIZE_8 0
459 # define R300_GB_TILE_SIZE_16 (1<<4)
460 # define R300_GB_TILE_SIZE_32 (2<<4)
461 # define R300_GB_SUPER_SIZE_1 (0<<6)
462 # define R300_GB_SUPER_SIZE_2 (1<<6)
463 # define R300_GB_SUPER_SIZE_4 (2<<6)
464 # define R300_GB_SUPER_SIZE_8 (3<<6)
465 # define R300_GB_SUPER_SIZE_16 (4<<6)
466 # define R300_GB_SUPER_SIZE_32 (5<<6)
467 # define R300_GB_SUPER_SIZE_64 (6<<6)
468 # define R300_GB_SUPER_SIZE_128 (7<<6)
469 # define R300_GB_SUPER_X_SHIFT 9 /* 3 bits wide */
470 # define R300_GB_SUPER_Y_SHIFT 12 /* 3 bits wide */
471 # define R300_GB_SUPER_TILE_A 0
472 # define R300_GB_SUPER_TILE_B (1<<15)
473 # define R300_GB_SUBPIXEL_1_12 0
474 # define R300_GB_SUBPIXEL_1_16 (1<<16)
476 #define R300_GB_FIFO_SIZE 0x4024
477 /* each of the following is 2 bits wide */
478 #define R300_GB_FIFO_SIZE_32 0
479 #define R300_GB_FIFO_SIZE_64 1
480 #define R300_GB_FIFO_SIZE_128 2
481 #define R300_GB_FIFO_SIZE_256 3
482 # define R300_SC_IFIFO_SIZE_SHIFT 0
483 # define R300_SC_TZFIFO_SIZE_SHIFT 2
484 # define R300_SC_BFIFO_SIZE_SHIFT 4
486 # define R300_US_OFIFO_SIZE_SHIFT 12
487 # define R300_US_WFIFO_SIZE_SHIFT 14
488 /* the following use the same constants as above, but meaning is
489 is times 2 (i.e. instead of 32 words it means 64 */
490 # define R300_RS_TFIFO_SIZE_SHIFT 6
491 # define R300_RS_CFIFO_SIZE_SHIFT 8
492 # define R300_US_RAM_SIZE_SHIFT 10
493 /* watermarks, 3 bits wide */
494 # define R300_RS_HIGHWATER_COL_SHIFT 16
495 # define R300_RS_HIGHWATER_TEX_SHIFT 19
496 # define R300_OFIFO_HIGHWATER_SHIFT 22 /* two bits only */
497 # define R300_CUBE_FIFO_HIGHWATER_COL_SHIFT 24
499 #define R300_GB_SELECT 0x401C
500 # define R300_GB_FOG_SELECT_C0A 0
501 # define R300_GB_FOG_SELECT_C1A 1
502 # define R300_GB_FOG_SELECT_C2A 2
503 # define R300_GB_FOG_SELECT_C3A 3
504 # define R300_GB_FOG_SELECT_1_1_W 4
505 # define R300_GB_FOG_SELECT_Z 5
506 # define R300_GB_DEPTH_SELECT_Z 0
507 # define R300_GB_DEPTH_SELECT_1_1_W (1<<3)
508 # define R300_GB_W_SELECT_1_W 0
509 # define R300_GB_W_SELECT_1 (1<<4)
511 #define R300_GB_AA_CONFIG 0x4020
512 # define R300_AA_DISABLE 0x00
513 # define R300_AA_ENABLE 0x01
514 # define R300_AA_SUBSAMPLES_2 0
515 # define R300_AA_SUBSAMPLES_3 (1<<1)
516 # define R300_AA_SUBSAMPLES_4 (2<<1)
517 # define R300_AA_SUBSAMPLES_6 (3<<1)
521 /* Zero to flush caches. */
522 #define R300_TX_INVALTAGS 0x4100
523 #define R300_TX_FLUSH 0x0
525 /* The upper enable bits are guessed, based on fglrx reported limits. */
526 #define R300_TX_ENABLE 0x4104
527 # define R300_TX_ENABLE_0 (1 << 0)
528 # define R300_TX_ENABLE_1 (1 << 1)
529 # define R300_TX_ENABLE_2 (1 << 2)
530 # define R300_TX_ENABLE_3 (1 << 3)
531 # define R300_TX_ENABLE_4 (1 << 4)
532 # define R300_TX_ENABLE_5 (1 << 5)
533 # define R300_TX_ENABLE_6 (1 << 6)
534 # define R300_TX_ENABLE_7 (1 << 7)
535 # define R300_TX_ENABLE_8 (1 << 8)
536 # define R300_TX_ENABLE_9 (1 << 9)
537 # define R300_TX_ENABLE_10 (1 << 10)
538 # define R300_TX_ENABLE_11 (1 << 11)
539 # define R300_TX_ENABLE_12 (1 << 12)
540 # define R300_TX_ENABLE_13 (1 << 13)
541 # define R300_TX_ENABLE_14 (1 << 14)
542 # define R300_TX_ENABLE_15 (1 << 15)
544 /* The pointsize is given in multiples of 6. The pointsize can be
545 * enormous: Clear() renders a single point that fills the entire
548 #define R300_RE_POINTSIZE 0x421C
549 # define R300_POINTSIZE_Y_SHIFT 0
550 # define R300_POINTSIZE_Y_MASK (0xFFFF << 0) /* GUESS */
551 # define R300_POINTSIZE_X_SHIFT 16
552 # define R300_POINTSIZE_X_MASK (0xFFFF << 16) /* GUESS */
553 # define R300_POINTSIZE_MAX (R300_POINTSIZE_Y_MASK / 6)
555 /* The line width is given in multiples of 6.
556 * In default mode lines are classified as vertical lines.
558 * VE: vertical or horizontal
559 * HO & VE: no classification
561 #define R300_RE_LINE_CNT 0x4234
562 # define R300_LINESIZE_SHIFT 0
563 # define R300_LINESIZE_MASK (0xFFFF << 0) /* GUESS */
564 # define R300_LINESIZE_MAX (R300_LINESIZE_MASK / 6)
565 # define R300_LINE_CNT_HO (1 << 16)
566 # define R300_LINE_CNT_VE (1 << 17)
568 /* Some sort of scale or clamp value for texcoordless textures. */
569 #define R300_RE_UNK4238 0x4238
571 /* Something shade related */
572 #define R300_RE_SHADE 0x4274
574 #define R300_RE_SHADE_MODEL 0x4278
575 # define R300_RE_SHADE_MODEL_SMOOTH 0x3aaaa
576 # define R300_RE_SHADE_MODEL_FLAT 0x39595
579 #define R300_RE_POLYGON_MODE 0x4288
580 # define R300_PM_ENABLED (1 << 0)
581 # define R300_PM_FRONT_POINT (0 << 0)
582 # define R300_PM_BACK_POINT (0 << 0)
583 # define R300_PM_FRONT_LINE (1 << 4)
584 # define R300_PM_FRONT_FILL (1 << 5)
585 # define R300_PM_BACK_LINE (1 << 7)
586 # define R300_PM_BACK_FILL (1 << 8)
589 #define R300_RE_FOG_SCALE 0x4294
590 #define R300_RE_FOG_START 0x4298
592 /* Not sure why there are duplicate of factor and constant values.
593 * My best guess so far is that there are separate zbiases for test and write.
594 * Ordering might be wrong.
595 * Some of the tests indicate that fgl has a fallback implementation of zbias
598 #define R300_RE_ZBIAS_CNTL 0x42A0 /* GUESS */
599 #define R300_RE_ZBIAS_T_FACTOR 0x42A4
600 #define R300_RE_ZBIAS_T_CONSTANT 0x42A8
601 #define R300_RE_ZBIAS_W_FACTOR 0x42AC
602 #define R300_RE_ZBIAS_W_CONSTANT 0x42B0
604 /* This register needs to be set to (1<<1) for RV350 to correctly
605 * perform depth test (see --vb-triangles in r300_demo)
606 * Don't know about other chips. - Vladimir
607 * This is set to 3 when GL_POLYGON_OFFSET_FILL is on.
608 * My guess is that there are two bits for each zbias primitive
609 * (FILL, LINE, POINT).
610 * One to enable depth test and one for depth write.
611 * Yet this doesn't explain why depth writes work ...
613 #define R300_RE_OCCLUSION_CNTL 0x42B4
614 # define R300_OCCLUSION_ON (1<<1)
616 #define R300_RE_CULL_CNTL 0x42B8
617 # define R300_CULL_FRONT (1 << 0)
618 # define R300_CULL_BACK (1 << 1)
619 # define R300_FRONT_FACE_CCW (0 << 2)
620 # define R300_FRONT_FACE_CW (1 << 2)
623 /* BEGIN: Rasterization / Interpolators - many guesses */
625 /* 0_UNKNOWN_18 has always been set except for clear operations.
626 * TC_CNT is the number of incoming texture coordinate sets (i.e. it depends
627 * on the vertex program, *not* the fragment program)
629 #define R300_RS_CNTL_0 0x4300
630 # define R300_RS_CNTL_TC_CNT_SHIFT 2
631 # define R300_RS_CNTL_TC_CNT_MASK (7 << 2)
632 /* number of color interpolators used */
633 # define R300_RS_CNTL_CI_CNT_SHIFT 7
634 # define R300_RS_CNTL_0_UNKNOWN_18 (1 << 18)
635 /* Guess: RS_CNTL_1 holds the index of the highest used RS_ROUTE_n
637 #define R300_RS_CNTL_1 0x4304
641 /* Only used for texture coordinates.
642 * Use the source field to route texture coordinate input from the
643 * vertex program to the desired interpolator. Note that the source
644 * field is relative to the outputs the vertex program *actually*
645 * writes. If a vertex program only writes texcoord[1], this will
647 * Set INTERP_USED on all interpolators that produce data used by
648 * the fragment program. INTERP_USED looks like a swizzling mask,
649 * but I haven't seen it used that way.
651 * Note: The _UNKNOWN constants are always set in their respective
652 * register. I don't know if this is necessary.
654 #define R300_RS_INTERP_0 0x4310
655 #define R300_RS_INTERP_1 0x4314
656 # define R300_RS_INTERP_1_UNKNOWN 0x40
657 #define R300_RS_INTERP_2 0x4318
658 # define R300_RS_INTERP_2_UNKNOWN 0x80
659 #define R300_RS_INTERP_3 0x431C
660 # define R300_RS_INTERP_3_UNKNOWN 0xC0
661 #define R300_RS_INTERP_4 0x4320
662 #define R300_RS_INTERP_5 0x4324
663 #define R300_RS_INTERP_6 0x4328
664 #define R300_RS_INTERP_7 0x432C
665 # define R300_RS_INTERP_SRC_SHIFT 2
666 # define R300_RS_INTERP_SRC_MASK (7 << 2)
667 # define R300_RS_INTERP_USED 0x00D10000
669 /* These DWORDs control how vertex data is routed into fragment program
670 * registers, after interpolators.
672 #define R300_RS_ROUTE_0 0x4330
673 #define R300_RS_ROUTE_1 0x4334
674 #define R300_RS_ROUTE_2 0x4338
675 #define R300_RS_ROUTE_3 0x433C /* GUESS */
676 #define R300_RS_ROUTE_4 0x4340 /* GUESS */
677 #define R300_RS_ROUTE_5 0x4344 /* GUESS */
678 #define R300_RS_ROUTE_6 0x4348 /* GUESS */
679 #define R300_RS_ROUTE_7 0x434C /* GUESS */
680 # define R300_RS_ROUTE_SOURCE_INTERP_0 0
681 # define R300_RS_ROUTE_SOURCE_INTERP_1 1
682 # define R300_RS_ROUTE_SOURCE_INTERP_2 2
683 # define R300_RS_ROUTE_SOURCE_INTERP_3 3
684 # define R300_RS_ROUTE_SOURCE_INTERP_4 4
685 # define R300_RS_ROUTE_SOURCE_INTERP_5 5 /* GUESS */
686 # define R300_RS_ROUTE_SOURCE_INTERP_6 6 /* GUESS */
687 # define R300_RS_ROUTE_SOURCE_INTERP_7 7 /* GUESS */
688 # define R300_RS_ROUTE_ENABLE (1 << 3) /* GUESS */
689 # define R300_RS_ROUTE_DEST_SHIFT 6
690 # define R300_RS_ROUTE_DEST_MASK (31 << 6) /* GUESS */
692 /* Special handling for color: When the fragment program uses color,
693 * the ROUTE_0_COLOR bit is set and ROUTE_0_COLOR_DEST contains the
694 * color register index.
696 * Apperently you may set the R300_RS_ROUTE_0_COLOR bit, but not provide any
697 * R300_RS_ROUTE_0_COLOR_DEST value; this setup is used for clearing the state.
698 * See r300_ioctl.c:r300EmitClearState. I'm not sure if this setup is strictly
699 * correct or not. - Oliver.
701 # define R300_RS_ROUTE_0_COLOR (1 << 14)
702 # define R300_RS_ROUTE_0_COLOR_DEST_SHIFT 17
703 # define R300_RS_ROUTE_0_COLOR_DEST_MASK (31 << 17) /* GUESS */
704 /* As above, but for secondary color */
705 # define R300_RS_ROUTE_1_COLOR1 (1 << 14)
706 # define R300_RS_ROUTE_1_COLOR1_DEST_SHIFT 17
707 # define R300_RS_ROUTE_1_COLOR1_DEST_MASK (31 << 17)
708 # define R300_RS_ROUTE_1_UNKNOWN11 (1 << 11)
709 /* END: Rasterization / Interpolators - many guesses */
711 /* Hierarchical Z Enable */
712 #define R300_SC_HYPERZ 0x43a4
713 # define R300_SC_HYPERZ_DISABLE (0 << 0)
714 # define R300_SC_HYPERZ_ENABLE (1 << 0)
715 # define R300_SC_HYPERZ_MIN (0 << 1)
716 # define R300_SC_HYPERZ_MAX (1 << 1)
717 # define R300_SC_HYPERZ_ADJ_256 (0 << 2)
718 # define R300_SC_HYPERZ_ADJ_128 (1 << 2)
719 # define R300_SC_HYPERZ_ADJ_64 (2 << 2)
720 # define R300_SC_HYPERZ_ADJ_32 (3 << 2)
721 # define R300_SC_HYPERZ_ADJ_16 (4 << 2)
722 # define R300_SC_HYPERZ_ADJ_8 (5 << 2)
723 # define R300_SC_HYPERZ_ADJ_4 (6 << 2)
724 # define R300_SC_HYPERZ_ADJ_2 (7 << 2)
725 # define R300_SC_HYPERZ_HZ_Z0MIN_NO (0 << 5)
726 # define R300_SC_HYPERZ_HZ_Z0MIN (1 << 5)
727 # define R300_SC_HYPERZ_HZ_Z0MAX_NO (0 << 6)
728 # define R300_SC_HYPERZ_HZ_Z0MAX (1 << 6)
730 #define R300_SC_EDGERULE 0x43a8
732 /* BEGIN: Scissors and cliprects */
734 /* There are four clipping rectangles. Their corner coordinates are inclusive.
735 * Every pixel is assigned a number from 0 and 15 by setting bits 0-3 depending
736 * on whether the pixel is inside cliprects 0-3, respectively. For example,
737 * if a pixel is inside cliprects 0 and 1, but outside 2 and 3, it is assigned
738 * the number 3 (binary 0011).
739 * Iff the bit corresponding to the pixel's number in RE_CLIPRECT_CNTL is set,
740 * the pixel is rasterized.
742 * In addition to this, there is a scissors rectangle. Only pixels inside the
743 * scissors rectangle are drawn. (coordinates are inclusive)
745 * For some reason, the top-left corner of the framebuffer is at (1440, 1440)
746 * for the purpose of clipping and scissors.
748 #define R300_RE_CLIPRECT_TL_0 0x43B0
749 #define R300_RE_CLIPRECT_BR_0 0x43B4
750 #define R300_RE_CLIPRECT_TL_1 0x43B8
751 #define R300_RE_CLIPRECT_BR_1 0x43BC
752 #define R300_RE_CLIPRECT_TL_2 0x43C0
753 #define R300_RE_CLIPRECT_BR_2 0x43C4
754 #define R300_RE_CLIPRECT_TL_3 0x43C8
755 #define R300_RE_CLIPRECT_BR_3 0x43CC
756 # define R300_CLIPRECT_OFFSET 1440
757 # define R300_CLIPRECT_MASK 0x1FFF
758 # define R300_CLIPRECT_X_SHIFT 0
759 # define R300_CLIPRECT_X_MASK (0x1FFF << 0)
760 # define R300_CLIPRECT_Y_SHIFT 13
761 # define R300_CLIPRECT_Y_MASK (0x1FFF << 13)
762 #define R300_RE_CLIPRECT_CNTL 0x43D0
763 # define R300_CLIP_OUT (1 << 0)
764 # define R300_CLIP_0 (1 << 1)
765 # define R300_CLIP_1 (1 << 2)
766 # define R300_CLIP_10 (1 << 3)
767 # define R300_CLIP_2 (1 << 4)
768 # define R300_CLIP_20 (1 << 5)
769 # define R300_CLIP_21 (1 << 6)
770 # define R300_CLIP_210 (1 << 7)
771 # define R300_CLIP_3 (1 << 8)
772 # define R300_CLIP_30 (1 << 9)
773 # define R300_CLIP_31 (1 << 10)
774 # define R300_CLIP_310 (1 << 11)
775 # define R300_CLIP_32 (1 << 12)
776 # define R300_CLIP_320 (1 << 13)
777 # define R300_CLIP_321 (1 << 14)
778 # define R300_CLIP_3210 (1 << 15)
782 #define R300_RE_SCISSORS_TL 0x43E0
783 #define R300_RE_SCISSORS_BR 0x43E4
784 # define R300_SCISSORS_OFFSET 1440
785 # define R300_SCISSORS_X_SHIFT 0
786 # define R300_SCISSORS_X_MASK (0x1FFF << 0)
787 # define R300_SCISSORS_Y_SHIFT 13
788 # define R300_SCISSORS_Y_MASK (0x1FFF << 13)
789 /* END: Scissors and cliprects */
791 /* BEGIN: Texture specification */
794 * The texture specification dwords are grouped by meaning and not by texture
795 * unit. This means that e.g. the offset for texture image unit N is found in
796 * register TX_OFFSET_0 + (4*N)
798 #define R300_TX_FILTER_0 0x4400
799 # define R300_TX_REPEAT 0
800 # define R300_TX_MIRRORED 1
801 # define R300_TX_CLAMP 4
802 # define R300_TX_CLAMP_TO_EDGE 2
803 # define R300_TX_CLAMP_TO_BORDER 6
804 # define R300_TX_WRAP_S_SHIFT 0
805 # define R300_TX_WRAP_S_MASK (7 << 0)
806 # define R300_TX_WRAP_T_SHIFT 3
807 # define R300_TX_WRAP_T_MASK (7 << 3)
808 # define R300_TX_WRAP_Q_SHIFT 6
809 # define R300_TX_WRAP_Q_MASK (7 << 6)
810 # define R300_TX_MAG_FILTER_NEAREST (1 << 9)
811 # define R300_TX_MAG_FILTER_LINEAR (2 << 9)
812 # define R300_TX_MAG_FILTER_MASK (3 << 9)
813 # define R300_TX_MIN_FILTER_NEAREST (1 << 11)
814 # define R300_TX_MIN_FILTER_LINEAR (2 << 11)
815 # define R300_TX_MIN_FILTER_NEAREST_MIP_NEAREST (5 << 11)
816 # define R300_TX_MIN_FILTER_NEAREST_MIP_LINEAR (9 << 11)
817 # define R300_TX_MIN_FILTER_LINEAR_MIP_NEAREST (6 << 11)
818 # define R300_TX_MIN_FILTER_LINEAR_MIP_LINEAR (10 << 11)
820 /* NOTE: NEAREST doesn't seem to exist.
821 * Im not seting MAG_FILTER_MASK and (3 << 11) on for all
822 * anisotropy modes because that would void selected mag filter
824 # define R300_TX_MIN_FILTER_ANISO_NEAREST (0 << 13)
825 # define R300_TX_MIN_FILTER_ANISO_LINEAR (0 << 13)
826 # define R300_TX_MIN_FILTER_ANISO_NEAREST_MIP_NEAREST (1 << 13)
827 # define R300_TX_MIN_FILTER_ANISO_NEAREST_MIP_LINEAR (2 << 13)
828 # define R300_TX_MIN_FILTER_MASK ( (15 << 11) | (3 << 13) )
829 # define R300_TX_MAX_ANISO_1_TO_1 (0 << 21)
830 # define R300_TX_MAX_ANISO_2_TO_1 (2 << 21)
831 # define R300_TX_MAX_ANISO_4_TO_1 (4 << 21)
832 # define R300_TX_MAX_ANISO_8_TO_1 (6 << 21)
833 # define R300_TX_MAX_ANISO_16_TO_1 (8 << 21)
834 # define R300_TX_MAX_ANISO_MASK (14 << 21)
836 #define R300_TX_FILTER1_0 0x4440
837 # define R300_CHROMA_KEY_MODE_DISABLE 0
838 # define R300_CHROMA_KEY_FORCE 1
839 # define R300_CHROMA_KEY_BLEND 2
840 # define R300_MC_ROUND_NORMAL (0<<2)
841 # define R300_MC_ROUND_MPEG4 (1<<2)
842 # define R300_LOD_BIAS_MASK 0x1fff
843 # define R300_EDGE_ANISO_EDGE_DIAG (0<<13)
844 # define R300_EDGE_ANISO_EDGE_ONLY (1<<13)
845 # define R300_MC_COORD_TRUNCATE_DISABLE (0<<14)
846 # define R300_MC_COORD_TRUNCATE_MPEG (1<<14)
847 # define R300_TX_TRI_PERF_0_8 (0<<15)
848 # define R300_TX_TRI_PERF_1_8 (1<<15)
849 # define R300_TX_TRI_PERF_1_4 (2<<15)
850 # define R300_TX_TRI_PERF_3_8 (3<<15)
851 # define R300_ANISO_THRESHOLD_MASK (7<<17)
853 #define R300_TX_SIZE_0 0x4480
854 # define R300_TX_WIDTHMASK_SHIFT 0
855 # define R300_TX_WIDTHMASK_MASK (2047 << 0)
856 # define R300_TX_HEIGHTMASK_SHIFT 11
857 # define R300_TX_HEIGHTMASK_MASK (2047 << 11)
858 # define R300_TX_UNK23 (1 << 23)
859 # define R300_TX_MAX_MIP_LEVEL_SHIFT 26
860 # define R300_TX_MAX_MIP_LEVEL_MASK (0xf << 26)
861 # define R300_TX_SIZE_PROJECTED (1<<30)
862 # define R300_TX_SIZE_TXPITCH_EN (1<<31)
863 #define R300_TX_FORMAT_0 0x44C0
864 /* The interpretation of the format word by Wladimir van der Laan */
865 /* The X, Y, Z and W refer to the layout of the components.
866 They are given meanings as R, G, B and Alpha by the swizzle
868 # define R300_TX_FORMAT_X8 0x0
869 # define R300_TX_FORMAT_X16 0x1
870 # define R300_TX_FORMAT_Y4X4 0x2
871 # define R300_TX_FORMAT_Y8X8 0x3
872 # define R300_TX_FORMAT_Y16X16 0x4
873 # define R300_TX_FORMAT_Z3Y3X2 0x5
874 # define R300_TX_FORMAT_Z5Y6X5 0x6
875 # define R300_TX_FORMAT_Z6Y5X5 0x7
876 # define R300_TX_FORMAT_Z11Y11X10 0x8
877 # define R300_TX_FORMAT_Z10Y11X11 0x9
878 # define R300_TX_FORMAT_W4Z4Y4X4 0xA
879 # define R300_TX_FORMAT_W1Z5Y5X5 0xB
880 # define R300_TX_FORMAT_W8Z8Y8X8 0xC
881 # define R300_TX_FORMAT_W2Z10Y10X10 0xD
882 # define R300_TX_FORMAT_W16Z16Y16X16 0xE
883 # define R300_TX_FORMAT_DXT1 0xF
884 # define R300_TX_FORMAT_DXT3 0x10
885 # define R300_TX_FORMAT_DXT5 0x11
886 # define R300_TX_FORMAT_D3DMFT_CxV8U8 0x12 /* no swizzle */
887 # define R300_TX_FORMAT_A8R8G8B8 0x13 /* no swizzle */
888 # define R300_TX_FORMAT_B8G8_B8G8 0x14 /* no swizzle */
889 # define R300_TX_FORMAT_G8R8_G8B8 0x15 /* no swizzle */
890 /* 0x16 - some 16 bit green format.. ?? */
891 # define R300_TX_FORMAT_UNK25 (1 << 25) /* no swizzle */
892 # define R300_TX_FORMAT_CUBIC_MAP (1 << 26)
895 /* Floating point formats */
896 /* Note - hardware supports both 16 and 32 bit floating point */
897 # define R300_TX_FORMAT_FL_I16 0x18
898 # define R300_TX_FORMAT_FL_I16A16 0x19
899 # define R300_TX_FORMAT_FL_R16G16B16A16 0x1A
900 # define R300_TX_FORMAT_FL_I32 0x1B
901 # define R300_TX_FORMAT_FL_I32A32 0x1C
902 # define R300_TX_FORMAT_FL_R32G32B32A32 0x1D
903 # define R300_TX_FORMAT_ATI2N 0x1F
904 /* alpha modes, convenience mostly */
905 /* if you have alpha, pick constant appropriate to the
906 number of channels (1 for I8, 2 for I8A8, 4 for R8G8B8A8, etc */
907 # define R300_TX_FORMAT_ALPHA_1CH 0x000
908 # define R300_TX_FORMAT_ALPHA_2CH 0x200
909 # define R300_TX_FORMAT_ALPHA_4CH 0x600
910 # define R300_TX_FORMAT_ALPHA_NONE 0xA00
913 # define R300_TX_FORMAT_X 0
914 # define R300_TX_FORMAT_Y 1
915 # define R300_TX_FORMAT_Z 2
916 # define R300_TX_FORMAT_W 3
917 # define R300_TX_FORMAT_ZERO 4
918 # define R300_TX_FORMAT_ONE 5
919 /* 2.0*Z, everything above 1.0 is set to 0.0 */
920 # define R300_TX_FORMAT_CUT_Z 6
921 /* 2.0*W, everything above 1.0 is set to 0.0 */
922 # define R300_TX_FORMAT_CUT_W 7
924 # define R300_TX_FORMAT_B_SHIFT 18
925 # define R300_TX_FORMAT_G_SHIFT 15
926 # define R300_TX_FORMAT_R_SHIFT 12
927 # define R300_TX_FORMAT_A_SHIFT 9
928 /* Convenience macro to take care of layout and swizzling */
929 # define R300_EASY_TX_FORMAT(B, G, R, A, FMT) ( \
930 ((R300_TX_FORMAT_##B)<<R300_TX_FORMAT_B_SHIFT) \
931 | ((R300_TX_FORMAT_##G)<<R300_TX_FORMAT_G_SHIFT) \
932 | ((R300_TX_FORMAT_##R)<<R300_TX_FORMAT_R_SHIFT) \
933 | ((R300_TX_FORMAT_##A)<<R300_TX_FORMAT_A_SHIFT) \
934 | (R300_TX_FORMAT_##FMT) \
936 /* These can be ORed with result of R300_EASY_TX_FORMAT()
937 We don't really know what they do. Take values from a
939 # define R300_TX_FORMAT_CONST_X (1<<5)
940 # define R300_TX_FORMAT_CONST_Y (2<<5)
941 # define R300_TX_FORMAT_CONST_Z (4<<5)
942 # define R300_TX_FORMAT_CONST_W (8<<5)
944 # define R300_TX_FORMAT_YUV_MODE 0x00800000
946 #define R300_TX_PITCH_0 0x4500 /* obvious missing in gap */
947 #define R300_TX_OFFSET_0 0x4540
948 /* BEGIN: Guess from R200 */
949 # define R300_TXO_ENDIAN_NO_SWAP (0 << 0)
950 # define R300_TXO_ENDIAN_BYTE_SWAP (1 << 0)
951 # define R300_TXO_ENDIAN_WORD_SWAP (2 << 0)
952 # define R300_TXO_ENDIAN_HALFDW_SWAP (3 << 0)
953 # define R300_TXO_MACRO_TILE (1 << 2)
954 # define R300_TXO_MICRO_TILE (1 << 3)
955 # define R300_TXO_MICRO_TILE_SQUARE (2 << 3)
956 # define R300_TXO_OFFSET_MASK 0xffffffe0
957 # define R300_TXO_OFFSET_SHIFT 5
958 /* END: Guess from R200 */
960 /* 32 bit chroma key */
961 #define R300_TX_CHROMA_KEY_0 0x4580
962 /* ff00ff00 == { 0, 1.0, 0, 1.0 } */
963 #define R300_TX_BORDER_COLOR_0 0x45C0
965 /* END: Texture specification */
967 /* BEGIN: Fragment program instruction set */
969 /* Fragment programs are written directly into register space.
970 * There are separate instruction streams for texture instructions and ALU
972 * In order to synchronize these streams, the program is divided into up
973 * to 4 nodes. Each node begins with a number of TEX operations, followed
974 * by a number of ALU operations.
975 * The first node can have zero TEX ops, all subsequent nodes must have at
978 * All nodes must have at least one ALU op.
980 * The index of the last node is stored in PFS_CNTL_0: A value of 0 means
981 * 1 node, a value of 3 means 4 nodes.
982 * The total amount of instructions is defined in PFS_CNTL_2. The offsets are
983 * offsets into the respective instruction streams, while *_END points to the
984 * last instruction relative to this offset.
986 #define R300_PFS_CNTL_0 0x4600
987 # define R300_PFS_CNTL_LAST_NODES_SHIFT 0
988 # define R300_PFS_CNTL_LAST_NODES_MASK (3 << 0)
989 # define R300_PFS_CNTL_FIRST_NODE_HAS_TEX (1 << 3)
990 #define R300_PFS_CNTL_1 0x4604
991 /* There is an unshifted value here which has so far always been equal to the
992 * index of the highest used temporary register.
994 #define R300_PFS_CNTL_2 0x4608
995 # define R300_PFS_CNTL_ALU_OFFSET_SHIFT 0
996 # define R300_PFS_CNTL_ALU_OFFSET_MASK (63 << 0)
997 # define R300_PFS_CNTL_ALU_END_SHIFT 6
998 # define R300_PFS_CNTL_ALU_END_MASK (63 << 6)
999 # define R300_PFS_CNTL_TEX_OFFSET_SHIFT 12
1000 # define R300_PFS_CNTL_TEX_OFFSET_MASK (31 << 12) /* GUESS */
1001 # define R300_PFS_CNTL_TEX_END_SHIFT 18
1002 # define R300_PFS_CNTL_TEX_END_MASK (31 << 18) /* GUESS */
1006 /* Nodes are stored backwards. The last active node is always stored in
1008 * Example: In a 2-node program, NODE_0 and NODE_1 are set to 0. The
1009 * first node is stored in NODE_2, the second node is stored in NODE_3.
1011 * Offsets are relative to the master offset from PFS_CNTL_2.
1013 #define R300_PFS_NODE_0 0x4610
1014 #define R300_PFS_NODE_1 0x4614
1015 #define R300_PFS_NODE_2 0x4618
1016 #define R300_PFS_NODE_3 0x461C
1017 # define R300_PFS_NODE_ALU_OFFSET_SHIFT 0
1018 # define R300_PFS_NODE_ALU_OFFSET_MASK (63 << 0)
1019 # define R300_PFS_NODE_ALU_END_SHIFT 6
1020 # define R300_PFS_NODE_ALU_END_MASK (63 << 6)
1021 # define R300_PFS_NODE_TEX_OFFSET_SHIFT 12
1022 # define R300_PFS_NODE_TEX_OFFSET_MASK (31 << 12)
1023 # define R300_PFS_NODE_TEX_END_SHIFT 17
1024 # define R300_PFS_NODE_TEX_END_MASK (31 << 17)
1025 # define R300_PFS_NODE_OUTPUT_COLOR (1 << 22)
1026 # define R300_PFS_NODE_OUTPUT_DEPTH (1 << 23)
1029 * As far as I can tell, texture instructions cannot write into output
1030 * registers directly. A subsequent ALU instruction is always necessary,
1031 * even if it's just MAD o0, r0, 1, 0
1033 #define R300_PFS_TEXI_0 0x4620
1034 # define R300_FPITX_SRC_SHIFT 0
1035 # define R300_FPITX_SRC_MASK (31 << 0)
1037 # define R300_FPITX_SRC_CONST (1 << 5)
1038 # define R300_FPITX_DST_SHIFT 6
1039 # define R300_FPITX_DST_MASK (31 << 6)
1040 # define R300_FPITX_IMAGE_SHIFT 11
1041 /* GUESS based on layout and native limits */
1042 # define R300_FPITX_IMAGE_MASK (15 << 11)
1043 /* Unsure if these are opcodes, or some kind of bitfield, but this is how
1044 * they were set when I checked
1046 # define R300_FPITX_OPCODE_SHIFT 15
1047 # define R300_FPITX_OP_TEX 1
1048 # define R300_FPITX_OP_KIL 2
1049 # define R300_FPITX_OP_TXP 3
1050 # define R300_FPITX_OP_TXB 4
1051 # define R300_FPITX_OPCODE_MASK (7 << 15)
1054 * The ALU instructions register blocks are enumerated according to the order
1055 * in which fglrx. I assume there is space for 64 instructions, since
1056 * each block has space for a maximum of 64 DWORDs, and this matches reported
1059 * The basic functional block seems to be one MAD for each color and alpha,
1060 * and an adder that adds all components after the MUL.
1061 * - ADD, MUL, MAD etc.: use MAD with appropriate neutral operands
1062 * - DP4: Use OUTC_DP4, OUTA_DP4
1063 * - DP3: Use OUTC_DP3, OUTA_DP4, appropriate alpha operands
1064 * - DPH: Use OUTC_DP4, OUTA_DP4, appropriate alpha operands
1065 * - CMPH: If ARG2 > 0.5, return ARG0, else return ARG1
1066 * - CMP: If ARG2 < 0, return ARG1, else return ARG0
1067 * - FLR: use FRC+MAD
1068 * - XPD: use MAD+MAD
1069 * - SGE, SLT: use MAD+CMP
1070 * - RSQ: use ABS modifier for argument
1071 * - Use OUTC_REPL_ALPHA to write results of an alpha-only operation
1072 * (e.g. RCP) into color register
1073 * - apparently, there's no quick DST operation
1074 * - fglrx set FPI2_UNKNOWN_31 on a "MAD fragment.color, tmp0, tmp1, tmp2"
1075 * - fglrx set FPI2_UNKNOWN_31 on a "MAX r2, r1, c0"
1076 * - fglrx once set FPI0_UNKNOWN_31 on a "FRC r1, r1"
1079 * First stage selects three sources from the available registers and
1080 * constant parameters. This is defined in INSTR1 (color) and INSTR3 (alpha).
1081 * fglrx sorts the three source fields: Registers before constants,
1082 * lower indices before higher indices; I do not know whether this is
1085 * fglrx fills unused sources with "read constant 0"
1086 * According to specs, you cannot select more than two different constants.
1088 * Second stage selects the operands from the sources. This is defined in
1089 * INSTR0 (color) and INSTR2 (alpha). You can also select the special constants
1091 * Swizzling and negation happens in this stage, as well.
1093 * Important: Color and alpha seem to be mostly separate, i.e. their sources
1094 * selection appears to be fully independent (the register storage is probably
1095 * physically split into a color and an alpha section).
1096 * However (because of the apparent physical split), there is some interaction
1097 * WRT swizzling. If, for example, you want to load an R component into an
1098 * Alpha operand, this R component is taken from a *color* source, not from
1099 * an alpha source. The corresponding register doesn't even have to appear in
1100 * the alpha sources list. (I hope this all makes sense to you)
1102 * Destination selection
1103 * The destination register index is in FPI1 (color) and FPI3 (alpha)
1104 * together with enable bits.
1105 * There are separate enable bits for writing into temporary registers
1106 * (DSTC_REG_* /DSTA_REG) and and program output registers (DSTC_OUTPUT_*
1107 * /DSTA_OUTPUT). You can write to both at once, or not write at all (the
1108 * same index must be used for both).
1110 * Note: There is a special form for LRP
1111 * - Argument order is the same as in ARB_fragment_program.
1112 * - Operation is MAD
1113 * - ARG1 is set to ARGC_SRC1C_LRP/ARGC_SRC1A_LRP
1114 * - Set FPI0/FPI2_SPECIAL_LRP
1115 * Arbitrary LRP (including support for swizzling) requires vanilla MAD+MAD
1117 #define R300_PFS_INSTR1_0 0x46C0
1118 # define R300_FPI1_SRC0C_SHIFT 0
1119 # define R300_FPI1_SRC0C_MASK (31 << 0)
1120 # define R300_FPI1_SRC0C_CONST (1 << 5)
1121 # define R300_FPI1_SRC1C_SHIFT 6
1122 # define R300_FPI1_SRC1C_MASK (31 << 6)
1123 # define R300_FPI1_SRC1C_CONST (1 << 11)
1124 # define R300_FPI1_SRC2C_SHIFT 12
1125 # define R300_FPI1_SRC2C_MASK (31 << 12)
1126 # define R300_FPI1_SRC2C_CONST (1 << 17)
1127 # define R300_FPI1_SRC_MASK 0x0003ffff
1128 # define R300_FPI1_DSTC_SHIFT 18
1129 # define R300_FPI1_DSTC_MASK (31 << 18)
1130 # define R300_FPI1_DSTC_REG_MASK_SHIFT 23
1131 # define R300_FPI1_DSTC_REG_X (1 << 23)
1132 # define R300_FPI1_DSTC_REG_Y (1 << 24)
1133 # define R300_FPI1_DSTC_REG_Z (1 << 25)
1134 # define R300_FPI1_DSTC_OUTPUT_MASK_SHIFT 26
1135 # define R300_FPI1_DSTC_OUTPUT_X (1 << 26)
1136 # define R300_FPI1_DSTC_OUTPUT_Y (1 << 27)
1137 # define R300_FPI1_DSTC_OUTPUT_Z (1 << 28)
1139 #define R300_PFS_INSTR3_0 0x47C0
1140 # define R300_FPI3_SRC0A_SHIFT 0
1141 # define R300_FPI3_SRC0A_MASK (31 << 0)
1142 # define R300_FPI3_SRC0A_CONST (1 << 5)
1143 # define R300_FPI3_SRC1A_SHIFT 6
1144 # define R300_FPI3_SRC1A_MASK (31 << 6)
1145 # define R300_FPI3_SRC1A_CONST (1 << 11)
1146 # define R300_FPI3_SRC2A_SHIFT 12
1147 # define R300_FPI3_SRC2A_MASK (31 << 12)
1148 # define R300_FPI3_SRC2A_CONST (1 << 17)
1149 # define R300_FPI3_SRC_MASK 0x0003ffff
1150 # define R300_FPI3_DSTA_SHIFT 18
1151 # define R300_FPI3_DSTA_MASK (31 << 18)
1152 # define R300_FPI3_DSTA_REG (1 << 23)
1153 # define R300_FPI3_DSTA_OUTPUT (1 << 24)
1154 # define R300_FPI3_DSTA_DEPTH (1 << 27)
1156 #define R300_PFS_INSTR0_0 0x48C0
1157 # define R300_FPI0_ARGC_SRC0C_XYZ 0
1158 # define R300_FPI0_ARGC_SRC0C_XXX 1
1159 # define R300_FPI0_ARGC_SRC0C_YYY 2
1160 # define R300_FPI0_ARGC_SRC0C_ZZZ 3
1161 # define R300_FPI0_ARGC_SRC1C_XYZ 4
1162 # define R300_FPI0_ARGC_SRC1C_XXX 5
1163 # define R300_FPI0_ARGC_SRC1C_YYY 6
1164 # define R300_FPI0_ARGC_SRC1C_ZZZ 7
1165 # define R300_FPI0_ARGC_SRC2C_XYZ 8
1166 # define R300_FPI0_ARGC_SRC2C_XXX 9
1167 # define R300_FPI0_ARGC_SRC2C_YYY 10
1168 # define R300_FPI0_ARGC_SRC2C_ZZZ 11
1169 # define R300_FPI0_ARGC_SRC0A 12
1170 # define R300_FPI0_ARGC_SRC1A 13
1171 # define R300_FPI0_ARGC_SRC2A 14
1172 # define R300_FPI0_ARGC_SRC1C_LRP 15
1173 # define R300_FPI0_ARGC_ZERO 20
1174 # define R300_FPI0_ARGC_ONE 21
1176 # define R300_FPI0_ARGC_HALF 22
1177 # define R300_FPI0_ARGC_SRC0C_YZX 23
1178 # define R300_FPI0_ARGC_SRC1C_YZX 24
1179 # define R300_FPI0_ARGC_SRC2C_YZX 25
1180 # define R300_FPI0_ARGC_SRC0C_ZXY 26
1181 # define R300_FPI0_ARGC_SRC1C_ZXY 27
1182 # define R300_FPI0_ARGC_SRC2C_ZXY 28
1183 # define R300_FPI0_ARGC_SRC0CA_WZY 29
1184 # define R300_FPI0_ARGC_SRC1CA_WZY 30
1185 # define R300_FPI0_ARGC_SRC2CA_WZY 31
1187 # define R300_FPI0_ARG0C_SHIFT 0
1188 # define R300_FPI0_ARG0C_MASK (31 << 0)
1189 # define R300_FPI0_ARG0C_NEG (1 << 5)
1190 # define R300_FPI0_ARG0C_ABS (1 << 6)
1191 # define R300_FPI0_ARG1C_SHIFT 7
1192 # define R300_FPI0_ARG1C_MASK (31 << 7)
1193 # define R300_FPI0_ARG1C_NEG (1 << 12)
1194 # define R300_FPI0_ARG1C_ABS (1 << 13)
1195 # define R300_FPI0_ARG2C_SHIFT 14
1196 # define R300_FPI0_ARG2C_MASK (31 << 14)
1197 # define R300_FPI0_ARG2C_NEG (1 << 19)
1198 # define R300_FPI0_ARG2C_ABS (1 << 20)
1199 # define R300_FPI0_SPECIAL_LRP (1 << 21)
1200 # define R300_FPI0_OUTC_MAD (0 << 23)
1201 # define R300_FPI0_OUTC_DP3 (1 << 23)
1202 # define R300_FPI0_OUTC_DP4 (2 << 23)
1203 # define R300_FPI0_OUTC_MIN (4 << 23)
1204 # define R300_FPI0_OUTC_MAX (5 << 23)
1205 # define R300_FPI0_OUTC_CMPH (7 << 23)
1206 # define R300_FPI0_OUTC_CMP (8 << 23)
1207 # define R300_FPI0_OUTC_FRC (9 << 23)
1208 # define R300_FPI0_OUTC_REPL_ALPHA (10 << 23)
1209 # define R300_FPI0_OUTC_SAT (1 << 30)
1210 # define R300_FPI0_INSERT_NOP (1 << 31)
1212 #define R300_PFS_INSTR2_0 0x49C0
1213 # define R300_FPI2_ARGA_SRC0C_X 0
1214 # define R300_FPI2_ARGA_SRC0C_Y 1
1215 # define R300_FPI2_ARGA_SRC0C_Z 2
1216 # define R300_FPI2_ARGA_SRC1C_X 3
1217 # define R300_FPI2_ARGA_SRC1C_Y 4
1218 # define R300_FPI2_ARGA_SRC1C_Z 5
1219 # define R300_FPI2_ARGA_SRC2C_X 6
1220 # define R300_FPI2_ARGA_SRC2C_Y 7
1221 # define R300_FPI2_ARGA_SRC2C_Z 8
1222 # define R300_FPI2_ARGA_SRC0A 9
1223 # define R300_FPI2_ARGA_SRC1A 10
1224 # define R300_FPI2_ARGA_SRC2A 11
1225 # define R300_FPI2_ARGA_SRC1A_LRP 15
1226 # define R300_FPI2_ARGA_ZERO 16
1227 # define R300_FPI2_ARGA_ONE 17
1229 # define R300_FPI2_ARGA_HALF 18
1230 # define R300_FPI2_ARG0A_SHIFT 0
1231 # define R300_FPI2_ARG0A_MASK (31 << 0)
1232 # define R300_FPI2_ARG0A_NEG (1 << 5)
1234 # define R300_FPI2_ARG0A_ABS (1 << 6)
1235 # define R300_FPI2_ARG1A_SHIFT 7
1236 # define R300_FPI2_ARG1A_MASK (31 << 7)
1237 # define R300_FPI2_ARG1A_NEG (1 << 12)
1239 # define R300_FPI2_ARG1A_ABS (1 << 13)
1240 # define R300_FPI2_ARG2A_SHIFT 14
1241 # define R300_FPI2_ARG2A_MASK (31 << 14)
1242 # define R300_FPI2_ARG2A_NEG (1 << 19)
1244 # define R300_FPI2_ARG2A_ABS (1 << 20)
1245 # define R300_FPI2_SPECIAL_LRP (1 << 21)
1246 # define R300_FPI2_OUTA_MAD (0 << 23)
1247 # define R300_FPI2_OUTA_DP4 (1 << 23)
1248 # define R300_FPI2_OUTA_MIN (2 << 23)
1249 # define R300_FPI2_OUTA_MAX (3 << 23)
1250 # define R300_FPI2_OUTA_CMP (6 << 23)
1251 # define R300_FPI2_OUTA_FRC (7 << 23)
1252 # define R300_FPI2_OUTA_EX2 (8 << 23)
1253 # define R300_FPI2_OUTA_LG2 (9 << 23)
1254 # define R300_FPI2_OUTA_RCP (10 << 23)
1255 # define R300_FPI2_OUTA_RSQ (11 << 23)
1256 # define R300_FPI2_OUTA_SAT (1 << 30)
1257 # define R300_FPI2_UNKNOWN_31 (1 << 31)
1258 /* END: Fragment program instruction set */
1260 /* Fog state and color */
1261 #define R300_RE_FOG_STATE 0x4BC0
1262 # define R300_FOG_ENABLE (1 << 0)
1263 # define R300_FOG_MODE_LINEAR (0 << 1)
1264 # define R300_FOG_MODE_EXP (1 << 1)
1265 # define R300_FOG_MODE_EXP2 (2 << 1)
1266 # define R300_FOG_MODE_MASK (3 << 1)
1267 #define R300_FOG_COLOR_R 0x4BC8
1268 #define R300_FOG_COLOR_G 0x4BCC
1269 #define R300_FOG_COLOR_B 0x4BD0
1271 #define R300_PP_ALPHA_TEST 0x4BD4
1272 # define R300_REF_ALPHA_MASK 0x000000ff
1273 # define R300_ALPHA_TEST_FAIL (0 << 8)
1274 # define R300_ALPHA_TEST_LESS (1 << 8)
1275 # define R300_ALPHA_TEST_LEQUAL (3 << 8)
1276 # define R300_ALPHA_TEST_EQUAL (2 << 8)
1277 # define R300_ALPHA_TEST_GEQUAL (6 << 8)
1278 # define R300_ALPHA_TEST_GREATER (4 << 8)
1279 # define R300_ALPHA_TEST_NEQUAL (5 << 8)
1280 # define R300_ALPHA_TEST_PASS (7 << 8)
1281 # define R300_ALPHA_TEST_OP_MASK (7 << 8)
1282 # define R300_ALPHA_TEST_ENABLE (1 << 11)
1286 /* Fragment program parameters in 7.16 floating point */
1287 #define R300_PFS_PARAM_0_X 0x4C00
1288 #define R300_PFS_PARAM_0_Y 0x4C04
1289 #define R300_PFS_PARAM_0_Z 0x4C08
1290 #define R300_PFS_PARAM_0_W 0x4C0C
1291 /* GUESS: PARAM_31 is last, based on native limits reported by fglrx */
1292 #define R300_PFS_PARAM_31_X 0x4DF0
1293 #define R300_PFS_PARAM_31_Y 0x4DF4
1294 #define R300_PFS_PARAM_31_Z 0x4DF8
1295 #define R300_PFS_PARAM_31_W 0x4DFC
1298 * - AFAIK fglrx always sets BLEND_UNKNOWN when blending is used in
1300 * - AFAIK fglrx always sets BLEND_NO_SEPARATE when CBLEND and ABLEND
1301 * are set to the same
1302 * function (both registers are always set up completely in any case)
1303 * - Most blend flags are simply copied from R200 and not tested yet
1305 #define R300_RB3D_CBLEND 0x4E04
1306 #define R300_RB3D_ABLEND 0x4E08
1307 /* the following only appear in CBLEND */
1308 # define R300_BLEND_ENABLE (1 << 0)
1309 # define R300_BLEND_UNKNOWN (3 << 1)
1310 # define R300_BLEND_NO_SEPARATE (1 << 3)
1311 /* the following are shared between CBLEND and ABLEND */
1312 # define R300_FCN_MASK (3 << 12)
1313 # define R300_COMB_FCN_ADD_CLAMP (0 << 12)
1314 # define R300_COMB_FCN_ADD_NOCLAMP (1 << 12)
1315 # define R300_COMB_FCN_SUB_CLAMP (2 << 12)
1316 # define R300_COMB_FCN_SUB_NOCLAMP (3 << 12)
1317 # define R300_COMB_FCN_MIN (4 << 12)
1318 # define R300_COMB_FCN_MAX (5 << 12)
1319 # define R300_COMB_FCN_RSUB_CLAMP (6 << 12)
1320 # define R300_COMB_FCN_RSUB_NOCLAMP (7 << 12)
1321 # define R300_BLEND_GL_ZERO (32)
1322 # define R300_BLEND_GL_ONE (33)
1323 # define R300_BLEND_GL_SRC_COLOR (34)
1324 # define R300_BLEND_GL_ONE_MINUS_SRC_COLOR (35)
1325 # define R300_BLEND_GL_DST_COLOR (36)
1326 # define R300_BLEND_GL_ONE_MINUS_DST_COLOR (37)
1327 # define R300_BLEND_GL_SRC_ALPHA (38)
1328 # define R300_BLEND_GL_ONE_MINUS_SRC_ALPHA (39)
1329 # define R300_BLEND_GL_DST_ALPHA (40)
1330 # define R300_BLEND_GL_ONE_MINUS_DST_ALPHA (41)
1331 # define R300_BLEND_GL_SRC_ALPHA_SATURATE (42)
1332 # define R300_BLEND_GL_CONST_COLOR (43)
1333 # define R300_BLEND_GL_ONE_MINUS_CONST_COLOR (44)
1334 # define R300_BLEND_GL_CONST_ALPHA (45)
1335 # define R300_BLEND_GL_ONE_MINUS_CONST_ALPHA (46)
1336 # define R300_BLEND_MASK (63)
1337 # define R300_SRC_BLEND_SHIFT (16)
1338 # define R300_DST_BLEND_SHIFT (24)
1339 #define R300_RB3D_BLEND_COLOR 0x4E10
1340 #define R300_RB3D_COLORMASK 0x4E0C
1341 # define R300_COLORMASK0_B (1<<0)
1342 # define R300_COLORMASK0_G (1<<1)
1343 # define R300_COLORMASK0_R (1<<2)
1344 # define R300_COLORMASK0_A (1<<3)
1348 #define R300_RB3D_COLOROFFSET0 0x4E28
1349 # define R300_COLOROFFSET_MASK 0xFFFFFFF0 /* GUESS */
1350 #define R300_RB3D_COLOROFFSET1 0x4E2C /* GUESS */
1351 #define R300_RB3D_COLOROFFSET2 0x4E30 /* GUESS */
1352 #define R300_RB3D_COLOROFFSET3 0x4E34 /* GUESS */
1356 /* Bit 16: Larger tiles
1358 * Bit 18: Extremely weird tile like, but some pixels duplicated?
1360 #define R300_RB3D_COLORPITCH0 0x4E38
1361 # define R300_COLORPITCH_MASK 0x00001FF8 /* GUESS */
1362 # define R300_COLOR_TILE_ENABLE (1 << 16) /* GUESS */
1363 # define R300_COLOR_MICROTILE_ENABLE (1 << 17) /* GUESS */
1364 # define R300_COLOR_MICROTILE_SQUARE_ENABLE (2 << 17)
1365 # define R300_COLOR_ENDIAN_NO_SWAP (0 << 18) /* GUESS */
1366 # define R300_COLOR_ENDIAN_WORD_SWAP (1 << 18) /* GUESS */
1367 # define R300_COLOR_ENDIAN_DWORD_SWAP (2 << 18) /* GUESS */
1368 # define R300_COLOR_FORMAT_RGB565 (2 << 22)
1369 # define R300_COLOR_FORMAT_ARGB8888 (3 << 22)
1370 #define R300_RB3D_COLORPITCH1 0x4E3C /* GUESS */
1371 #define R300_RB3D_COLORPITCH2 0x4E40 /* GUESS */
1372 #define R300_RB3D_COLORPITCH3 0x4E44 /* GUESS */
1374 #define R300_RB3D_AARESOLVE_OFFSET 0x4E80
1375 #define R300_RB3D_AARESOLVE_PITCH 0x4E84
1376 #define R300_RB3D_AARESOLVE_CTL 0x4E88
1379 /* Guess by Vladimir.
1380 * Set to 0A before 3D operations, set to 02 afterwards.
1382 /*#define R300_RB3D_DSTCACHE_CTLSTAT 0x4E4C*/
1383 # define R300_RB3D_DSTCACHE_UNKNOWN_02 0x00000002
1384 # define R300_RB3D_DSTCACHE_UNKNOWN_0A 0x0000000A
1387 /* There seems to be no "write only" setting, so use Z-test = ALWAYS
1389 * Bit (1<<8) is the "test" bit. so plain write is 6 - vd
1391 #define R300_ZB_CNTL 0x4F00
1392 # define R300_STENCIL_ENABLE (1 << 0)
1393 # define R300_Z_ENABLE (1 << 1)
1394 # define R300_Z_WRITE_ENABLE (1 << 2)
1395 # define R300_Z_SIGNED_COMPARE (1 << 3)
1396 # define R300_STENCIL_FRONT_BACK (1 << 4)
1398 #define R300_ZB_ZSTENCILCNTL 0x4f04
1400 # define R300_ZS_NEVER 0
1401 # define R300_ZS_LESS 1
1402 # define R300_ZS_LEQUAL 2
1403 # define R300_ZS_EQUAL 3
1404 # define R300_ZS_GEQUAL 4
1405 # define R300_ZS_GREATER 5
1406 # define R300_ZS_NOTEQUAL 6
1407 # define R300_ZS_ALWAYS 7
1408 # define R300_ZS_MASK 7
1410 # define R300_ZS_KEEP 0
1411 # define R300_ZS_ZERO 1
1412 # define R300_ZS_REPLACE 2
1413 # define R300_ZS_INCR 3
1414 # define R300_ZS_DECR 4
1415 # define R300_ZS_INVERT 5
1416 # define R300_ZS_INCR_WRAP 6
1417 # define R300_ZS_DECR_WRAP 7
1418 # define R300_Z_FUNC_SHIFT 0
1419 /* front and back refer to operations done for front
1420 and back faces, i.e. separate stencil function support */
1421 # define R300_S_FRONT_FUNC_SHIFT 3
1422 # define R300_S_FRONT_SFAIL_OP_SHIFT 6
1423 # define R300_S_FRONT_ZPASS_OP_SHIFT 9
1424 # define R300_S_FRONT_ZFAIL_OP_SHIFT 12
1425 # define R300_S_BACK_FUNC_SHIFT 15
1426 # define R300_S_BACK_SFAIL_OP_SHIFT 18
1427 # define R300_S_BACK_ZPASS_OP_SHIFT 21
1428 # define R300_S_BACK_ZFAIL_OP_SHIFT 24
1430 #define R300_ZB_STENCILREFMASK 0x4f08
1431 # define R300_STENCILREF_SHIFT 0
1432 # define R300_STENCILREF_MASK 0x000000ff
1433 # define R300_STENCILMASK_SHIFT 8
1434 # define R300_STENCILMASK_MASK 0x0000ff00
1435 # define R300_STENCILWRITEMASK_SHIFT 16
1436 # define R300_STENCILWRITEMASK_MASK 0x00ff0000
1440 #define R300_ZB_FORMAT 0x4f10
1441 # define R300_DEPTHFORMAT_16BIT_INT_Z (0 << 0)
1442 # define R300_DEPTHFORMAT_16BIT_13E3 (1 << 0)
1443 # define R300_DEPTHFORMAT_24BIT_INT_Z_8BIT_STENCIL (2 << 0)
1444 /* reserved up to (15 << 0) */
1445 # define R300_INVERT_13E3_LEADING_ONES (0 << 4)
1446 # define R300_INVERT_13E3_LEADING_ZEROS (1 << 4)
1448 #define R300_ZB_ZTOP 0x4F14
1449 # define R300_ZTOP_DISABLE (0 << 0)
1450 # define R300_ZTOP_ENABLE (1 << 0)
1454 #define R300_ZB_ZCACHE_CTLSTAT 0x4f18
1455 # define R300_ZB_ZCACHE_CTLSTAT_ZC_FLUSH_NO_EFFECT (0 << 0)
1456 # define R300_ZB_ZCACHE_CTLSTAT_ZC_FLUSH_FLUSH_AND_FREE (1 << 0)
1457 # define R300_ZB_ZCACHE_CTLSTAT_ZC_FREE_NO_EFFECT (0 << 1)
1458 # define R300_ZB_ZCACHE_CTLSTAT_ZC_FREE_FREE (1 << 1)
1459 # define R300_ZB_ZCACHE_CTLSTAT_ZC_BUSY_IDLE (0 << 31)
1460 # define R300_ZB_ZCACHE_CTLSTAT_ZC_BUSY_BUSY (1 << 31)
1462 #define R300_ZB_BW_CNTL 0x4f1c
1463 # define R300_HIZ_DISABLE (0 << 0)
1464 # define R300_HIZ_ENABLE (1 << 0)
1465 # define R300_HIZ_MIN (0 << 1)
1466 # define R300_HIZ_MAX (1 << 1)
1467 # define R300_FAST_FILL_DISABLE (0 << 2)
1468 # define R300_FAST_FILL_ENABLE (1 << 2)
1469 # define R300_RD_COMP_DISABLE (0 << 3)
1470 # define R300_RD_COMP_ENABLE (1 << 3)
1471 # define R300_WR_COMP_DISABLE (0 << 4)
1472 # define R300_WR_COMP_ENABLE (1 << 4)
1473 # define R300_ZB_CB_CLEAR_RMW (0 << 5)
1474 # define R300_ZB_CB_CLEAR_CACHE_LINEAR (1 << 5)
1475 # define R300_FORCE_COMPRESSED_STENCIL_VALUE_DISABLE (0 << 6)
1476 # define R300_FORCE_COMPRESSED_STENCIL_VALUE_ENABLE (1 << 6)
1478 # define R500_ZEQUAL_OPTIMIZE_ENABLE (0 << 7)
1479 # define R500_ZEQUAL_OPTIMIZE_DISABLE (1 << 7)
1480 # define R500_SEQUAL_OPTIMIZE_ENABLE (0 << 8)
1481 # define R500_SEQUAL_OPTIMIZE_DISABLE (1 << 8)
1483 # define R500_BMASK_ENABLE (0 << 10)
1484 # define R500_BMASK_DISABLE (1 << 10)
1485 # define R500_HIZ_EQUAL_REJECT_DISABLE (0 << 11)
1486 # define R500_HIZ_EQUAL_REJECT_ENABLE (1 << 11)
1487 # define R500_HIZ_FP_EXP_BITS_DISABLE (0 << 12)
1488 # define R500_HIZ_FP_EXP_BITS_1 (1 << 12)
1489 # define R500_HIZ_FP_EXP_BITS_2 (2 << 12)
1490 # define R500_HIZ_FP_EXP_BITS_3 (3 << 12)
1491 # define R500_HIZ_FP_EXP_BITS_4 (4 << 12)
1492 # define R500_HIZ_FP_EXP_BITS_5 (5 << 12)
1493 # define R500_HIZ_FP_INVERT_LEADING_ONES (0 << 15)
1494 # define R500_HIZ_FP_INVERT_LEADING_ZEROS (1 << 15)
1495 # define R500_TILE_OVERWRITE_RECOMPRESSION_ENABLE (0 << 16)
1496 # define R500_TILE_OVERWRITE_RECOMPRESSION_DISABLE (1 << 16)
1497 # define R500_CONTIGUOUS_6XAA_SAMPLES_ENABLE (0 << 17)
1498 # define R500_CONTIGUOUS_6XAA_SAMPLES_DISABLE (1 << 17)
1499 # define R500_PEQ_PACKING_DISABLE (0 << 18)
1500 # define R500_PEQ_PACKING_ENABLE (1 << 18)
1501 # define R500_COVERED_PTR_MASKING_DISABLE (0 << 18)
1502 # define R500_COVERED_PTR_MASKING_ENABLE (1 << 18)
1507 /* Z Buffer Address Offset.
1508 * Bits 31 to 5 are used for aligned Z buffer address offset for macro tiles.
1510 #define R300_ZB_DEPTHOFFSET 0x4f20
1512 /* Z Buffer Pitch and Endian Control */
1513 #define R300_ZB_DEPTHPITCH 0x4f24
1514 # define R300_DEPTHPITCH_MASK 0x00003FFC
1515 # define R300_DEPTHMACROTILE_DISABLE (0 << 16)
1516 # define R300_DEPTHMACROTILE_ENABLE (1 << 16)
1517 # define R300_DEPTHMICROTILE_LINEAR (0 << 17)
1518 # define R300_DEPTHMICROTILE_TILED (1 << 17)
1519 # define R300_DEPTHMICROTILE_TILED_SQUARE (2 << 17)
1520 # define R300_DEPTHENDIAN_NO_SWAP (0 << 18)
1521 # define R300_DEPTHENDIAN_WORD_SWAP (1 << 18)
1522 # define R300_DEPTHENDIAN_DWORD_SWAP (2 << 18)
1523 # define R300_DEPTHENDIAN_HALF_DWORD_SWAP (3 << 18)
1525 /* Z Buffer Clear Value */
1526 #define R300_ZB_DEPTHCLEARVALUE 0x4f28
1528 #define R300_ZB_ZMASK_OFFSET 0x4f30
1529 #define R300_ZB_ZMASK_PITCH 0x4f34
1530 #define R300_ZB_ZMASK_WRINDEX 0x4f38
1531 #define R300_ZB_ZMASK_DWORD 0x4f3c
1532 #define R300_ZB_ZMASK_RDINDEX 0x4f40
1534 /* Hierarchical Z Memory Offset */
1535 #define R300_ZB_HIZ_OFFSET 0x4f44
1537 /* Hierarchical Z Write Index */
1538 #define R300_ZB_HIZ_WRINDEX 0x4f48
1540 /* Hierarchical Z Data */
1541 #define R300_ZB_HIZ_DWORD 0x4f4c
1543 /* Hierarchical Z Read Index */
1544 #define R300_ZB_HIZ_RDINDEX 0x4f50
1546 /* Hierarchical Z Pitch */
1547 #define R300_ZB_HIZ_PITCH 0x4f54
1549 /* Z Buffer Z Pass Counter Data */
1550 #define R300_ZB_ZPASS_DATA 0x4f58
1552 /* Z Buffer Z Pass Counter Address */
1553 #define R300_ZB_ZPASS_ADDR 0x4f5c
1555 /* Depth buffer X and Y coordinate offset */
1556 #define R300_ZB_DEPTHXY_OFFSET 0x4f60
1557 # define R300_DEPTHX_OFFSET_SHIFT 1
1558 # define R300_DEPTHX_OFFSET_MASK 0x000007FE
1559 # define R300_DEPTHY_OFFSET_SHIFT 17
1560 # define R300_DEPTHY_OFFSET_MASK 0x07FE0000
1562 /* Sets the fifo sizes */
1563 #define R500_ZB_FIFO_SIZE 0x4fd0
1564 # define R500_OP_FIFO_SIZE_FULL (0 << 0)
1565 # define R500_OP_FIFO_SIZE_HALF (1 << 0)
1566 # define R500_OP_FIFO_SIZE_QUATER (2 << 0)
1567 # define R500_OP_FIFO_SIZE_EIGTHS (4 << 0)
1569 /* Stencil Reference Value and Mask for backfacing quads */
1570 /* R300_ZB_STENCILREFMASK handles front face */
1571 #define R500_ZB_STENCILREFMASK_BF 0x4fd4
1572 # define R500_STENCILREF_SHIFT 0
1573 # define R500_STENCILREF_MASK 0x000000ff
1574 # define R500_STENCILMASK_SHIFT 8
1575 # define R500_STENCILMASK_MASK 0x0000ff00
1576 # define R500_STENCILWRITEMASK_SHIFT 16
1577 # define R500_STENCILWRITEMASK_MASK 0x00ff0000
1579 /* BEGIN: Vertex program instruction set */
1581 /* Every instruction is four dwords long:
1582 * DWORD 0: output and opcode
1583 * DWORD 1: first argument
1584 * DWORD 2: second argument
1585 * DWORD 3: third argument
1588 * - ABS r, a is implemented as MAX r, a, -a
1589 * - MOV is implemented as ADD to zero
1590 * - XPD is implemented as MUL + MAD
1591 * - FLR is implemented as FRC + ADD
1592 * - apparently, fglrx tries to schedule instructions so that there is at
1593 * least one instruction between the write to a temporary and the first
1594 * read from said temporary; however, violations of this scheduling are
1596 * - register indices seem to be unrelated with OpenGL aliasing to
1597 * conventional state
1598 * - only one attribute and one parameter can be loaded at a time; however,
1599 * the same attribute/parameter can be used for more than one argument
1600 * - the second software argument for POW is the third hardware argument
1602 * - MAD with only temporaries as input seems to use VPI_OUT_SELECT_MAD_2
1604 * There is some magic surrounding LIT:
1605 * The single argument is replicated across all three inputs, but swizzled:
1606 * First argument: xyzy
1607 * Second argument: xyzx
1608 * Third argument: xyzw
1609 * Whenever the result is used later in the fragment program, fglrx forces
1610 * x and w to be 1.0 in the input selection; I don't know whether this is
1611 * strictly necessary
1613 #define R300_VPI_OUT_OP_DOT (1 << 0)
1614 #define R300_VPI_OUT_OP_MUL (2 << 0)
1615 #define R300_VPI_OUT_OP_ADD (3 << 0)
1616 #define R300_VPI_OUT_OP_MAD (4 << 0)
1617 #define R300_VPI_OUT_OP_DST (5 << 0)
1618 #define R300_VPI_OUT_OP_FRC (6 << 0)
1619 #define R300_VPI_OUT_OP_MAX (7 << 0)
1620 #define R300_VPI_OUT_OP_MIN (8 << 0)
1621 #define R300_VPI_OUT_OP_SGE (9 << 0)
1622 #define R300_VPI_OUT_OP_SLT (10 << 0)
1623 /* Used in GL_POINT_DISTANCE_ATTENUATION_ARB, vector(scalar, vector) */
1624 #define R300_VPI_OUT_OP_UNK12 (12 << 0)
1625 #define R300_VPI_OUT_OP_ARL (13 << 0)
1626 #define R300_VPI_OUT_OP_EXP (65 << 0)
1627 #define R300_VPI_OUT_OP_LOG (66 << 0)
1628 /* Used in fog computations, scalar(scalar) */
1629 #define R300_VPI_OUT_OP_UNK67 (67 << 0)
1630 #define R300_VPI_OUT_OP_LIT (68 << 0)
1631 #define R300_VPI_OUT_OP_POW (69 << 0)
1632 #define R300_VPI_OUT_OP_RCP (70 << 0)
1633 #define R300_VPI_OUT_OP_RSQ (72 << 0)
1634 /* Used in GL_POINT_DISTANCE_ATTENUATION_ARB, scalar(scalar) */
1635 #define R300_VPI_OUT_OP_UNK73 (73 << 0)
1636 #define R300_VPI_OUT_OP_EX2 (75 << 0)
1637 #define R300_VPI_OUT_OP_LG2 (76 << 0)
1638 #define R300_VPI_OUT_OP_MAD_2 (128 << 0)
1639 /* all temps, vector(scalar, vector, vector) */
1640 #define R300_VPI_OUT_OP_UNK129 (129 << 0)
1642 #define R300_VPI_OUT_REG_CLASS_TEMPORARY (0 << 8)
1643 #define R300_VPI_OUT_REG_CLASS_ADDR (1 << 8)
1644 #define R300_VPI_OUT_REG_CLASS_RESULT (2 << 8)
1645 #define R300_VPI_OUT_REG_CLASS_MASK (31 << 8)
1647 #define R300_VPI_OUT_REG_INDEX_SHIFT 13
1648 /* GUESS based on fglrx native limits */
1649 #define R300_VPI_OUT_REG_INDEX_MASK (31 << 13)
1651 #define R300_VPI_OUT_WRITE_X (1 << 20)
1652 #define R300_VPI_OUT_WRITE_Y (1 << 21)
1653 #define R300_VPI_OUT_WRITE_Z (1 << 22)
1654 #define R300_VPI_OUT_WRITE_W (1 << 23)
1656 #define R300_VPI_IN_REG_CLASS_TEMPORARY (0 << 0)
1657 #define R300_VPI_IN_REG_CLASS_ATTRIBUTE (1 << 0)
1658 #define R300_VPI_IN_REG_CLASS_PARAMETER (2 << 0)
1659 #define R300_VPI_IN_REG_CLASS_NONE (9 << 0)
1660 #define R300_VPI_IN_REG_CLASS_MASK (31 << 0)
1662 #define R300_VPI_IN_REG_INDEX_SHIFT 5
1663 /* GUESS based on fglrx native limits */
1664 #define R300_VPI_IN_REG_INDEX_MASK (255 << 5)
1666 /* The R300 can select components from the input register arbitrarily.
1667 * Use the following constants, shifted by the component shift you
1670 #define R300_VPI_IN_SELECT_X 0
1671 #define R300_VPI_IN_SELECT_Y 1
1672 #define R300_VPI_IN_SELECT_Z 2
1673 #define R300_VPI_IN_SELECT_W 3
1674 #define R300_VPI_IN_SELECT_ZERO 4
1675 #define R300_VPI_IN_SELECT_ONE 5
1676 #define R300_VPI_IN_SELECT_MASK 7
1678 #define R300_VPI_IN_X_SHIFT 13
1679 #define R300_VPI_IN_Y_SHIFT 16
1680 #define R300_VPI_IN_Z_SHIFT 19
1681 #define R300_VPI_IN_W_SHIFT 22
1683 #define R300_VPI_IN_NEG_X (1 << 25)
1684 #define R300_VPI_IN_NEG_Y (1 << 26)
1685 #define R300_VPI_IN_NEG_Z (1 << 27)
1686 #define R300_VPI_IN_NEG_W (1 << 28)
1687 /* END: Vertex program instruction set */
1689 /* BEGIN: Packet 3 commands */
1691 /* A primitive emission dword. */
1692 #define R300_PRIM_TYPE_NONE (0 << 0)
1693 #define R300_PRIM_TYPE_POINT (1 << 0)
1694 #define R300_PRIM_TYPE_LINE (2 << 0)
1695 #define R300_PRIM_TYPE_LINE_STRIP (3 << 0)
1696 #define R300_PRIM_TYPE_TRI_LIST (4 << 0)
1697 #define R300_PRIM_TYPE_TRI_FAN (5 << 0)
1698 #define R300_PRIM_TYPE_TRI_STRIP (6 << 0)
1699 #define R300_PRIM_TYPE_TRI_TYPE2 (7 << 0)
1700 #define R300_PRIM_TYPE_RECT_LIST (8 << 0)
1701 #define R300_PRIM_TYPE_3VRT_POINT_LIST (9 << 0)
1702 #define R300_PRIM_TYPE_3VRT_LINE_LIST (10 << 0)
1703 /* GUESS (based on r200) */
1704 #define R300_PRIM_TYPE_POINT_SPRITES (11 << 0)
1705 #define R300_PRIM_TYPE_LINE_LOOP (12 << 0)
1706 #define R300_PRIM_TYPE_QUADS (13 << 0)
1707 #define R300_PRIM_TYPE_QUAD_STRIP (14 << 0)
1708 #define R300_PRIM_TYPE_POLYGON (15 << 0)
1709 #define R300_PRIM_TYPE_MASK 0xF
1710 #define R300_PRIM_WALK_IND (1 << 4)
1711 #define R300_PRIM_WALK_LIST (2 << 4)
1712 #define R300_PRIM_WALK_RING (3 << 4)
1713 #define R300_PRIM_WALK_MASK (3 << 4)
1714 /* GUESS (based on r200) */
1715 #define R300_PRIM_COLOR_ORDER_BGRA (0 << 6)
1716 #define R300_PRIM_COLOR_ORDER_RGBA (1 << 6)
1717 #define R300_PRIM_NUM_VERTICES_SHIFT 16
1718 #define R300_PRIM_NUM_VERTICES_MASK 0xffff
1720 /* Draw a primitive from vertex data in arrays loaded via 3D_LOAD_VBPNTR.
1721 * Two parameter dwords:
1722 * 0. The first parameter appears to be always 0
1723 * 1. The second parameter is a standard primitive emission dword.
1725 #define R300_PACKET3_3D_DRAW_VBUF 0x00002800
1727 /* Specify the full set of vertex arrays as (address, stride).
1728 * The first parameter is the number of vertex arrays specified.
1729 * The rest of the command is a variable length list of blocks, where
1730 * each block is three dwords long and specifies two arrays.
1731 * The first dword of a block is split into two words, the lower significant
1732 * word refers to the first array, the more significant word to the second
1733 * array in the block.
1734 * The low byte of each word contains the size of an array entry in dwords,
1735 * the high byte contains the stride of the array.
1736 * The second dword of a block contains the pointer to the first array,
1737 * the third dword of a block contains the pointer to the second array.
1738 * Note that if the total number of arrays is odd, the third dword of
1739 * the last block is omitted.
1741 #define R300_PACKET3_3D_LOAD_VBPNTR 0x00002F00
1743 #define R300_PACKET3_INDX_BUFFER 0x00003300
1744 # define R300_EB_UNK1_SHIFT 24
1745 # define R300_EB_UNK1 (0x80<<24)
1746 # define R300_EB_UNK2 0x0810
1747 #define R300_PACKET3_3D_DRAW_VBUF_2 0x00003400
1748 #define R300_PACKET3_3D_DRAW_INDX_2 0x00003600
1750 /* END: Packet 3 commands */
1753 /* Color formats for 2d packets
1755 #define R300_CP_COLOR_FORMAT_CI8 2
1756 #define R300_CP_COLOR_FORMAT_ARGB1555 3
1757 #define R300_CP_COLOR_FORMAT_RGB565 4
1758 #define R300_CP_COLOR_FORMAT_ARGB8888 6
1759 #define R300_CP_COLOR_FORMAT_RGB332 7
1760 #define R300_CP_COLOR_FORMAT_RGB8 9
1761 #define R300_CP_COLOR_FORMAT_ARGB4444 15
1766 #define R300_CP_CMD_BITBLT_MULTI 0xC0009B00
1768 #define R500_VAP_INDEX_OFFSET 0x208c
1770 #define R500_GA_US_VECTOR_INDEX 0x4250
1771 #define R500_GA_US_VECTOR_DATA 0x4254
1773 #define R500_RS_IP_0 0x4074
1774 #define R500_RS_INST_0 0x4320
1776 #define R500_US_CONFIG 0x4600
1778 #define R500_US_FC_CTRL 0x4624
1779 #define R500_US_CODE_ADDR 0x4630
1781 #define R500_RB3D_COLOR_CLEAR_VALUE_AR 0x46c0
1782 #define R500_RB3D_CONSTANT_COLOR_AR 0x4ef8
1784 #define R300_SU_REG_DEST 0x42c8
1785 #define RV530_FG_ZBREG_DEST 0x4be8
1786 #define R300_ZB_ZPASS_DATA 0x4f58
1787 #define R300_ZB_ZPASS_ADDR 0x4f5c
1789 #endif /* _R300_REG_H */
git.openpandora.org / pandora-kernel.git / blob