mips: Fix i8253 clockevent fallout
[pandora-kernel.git] / drivers / gpio / adp5588-gpio.c
1 /*
2  * GPIO Chip driver for Analog Devices
3  * ADP5588/ADP5587 I/O Expander and QWERTY Keypad Controller
4  *
5  * Copyright 2009-2010 Analog Devices Inc.
6  *
7  * Licensed under the GPL-2 or later.
8  */
9
10 #include <linux/module.h>
11 #include <linux/kernel.h>
12 #include <linux/slab.h>
13 #include <linux/init.h>
14 #include <linux/i2c.h>
15 #include <linux/gpio.h>
16 #include <linux/interrupt.h>
17 #include <linux/irq.h>
18
19 #include <linux/i2c/adp5588.h>
20
21 #define DRV_NAME        "adp5588-gpio"
22
23 /*
24  * Early pre 4.0 Silicon required to delay readout by at least 25ms,
25  * since the Event Counter Register updated 25ms after the interrupt
26  * asserted.
27  */
28 #define WA_DELAYED_READOUT_REVID(rev)   ((rev) < 4)
29
30 struct adp5588_gpio {
31         struct i2c_client *client;
32         struct gpio_chip gpio_chip;
33         struct mutex lock;      /* protect cached dir, dat_out */
34         /* protect serialized access to the interrupt controller bus */
35         struct mutex irq_lock;
36         unsigned gpio_start;
37         unsigned irq_base;
38         uint8_t dat_out[3];
39         uint8_t dir[3];
40         uint8_t int_lvl[3];
41         uint8_t int_en[3];
42         uint8_t irq_mask[3];
43         uint8_t irq_stat[3];
44 };
45
46 static int adp5588_gpio_read(struct i2c_client *client, u8 reg)
47 {
48         int ret = i2c_smbus_read_byte_data(client, reg);
49
50         if (ret < 0)
51                 dev_err(&client->dev, "Read Error\n");
52
53         return ret;
54 }
55
56 static int adp5588_gpio_write(struct i2c_client *client, u8 reg, u8 val)
57 {
58         int ret = i2c_smbus_write_byte_data(client, reg, val);
59
60         if (ret < 0)
61                 dev_err(&client->dev, "Write Error\n");
62
63         return ret;
64 }
65
66 static int adp5588_gpio_get_value(struct gpio_chip *chip, unsigned off)
67 {
68         struct adp5588_gpio *dev =
69             container_of(chip, struct adp5588_gpio, gpio_chip);
70
71         return !!(adp5588_gpio_read(dev->client,
72                   GPIO_DAT_STAT1 + ADP5588_BANK(off)) & ADP5588_BIT(off));
73 }
74
75 static void adp5588_gpio_set_value(struct gpio_chip *chip,
76                                    unsigned off, int val)
77 {
78         unsigned bank, bit;
79         struct adp5588_gpio *dev =
80             container_of(chip, struct adp5588_gpio, gpio_chip);
81
82         bank = ADP5588_BANK(off);
83         bit = ADP5588_BIT(off);
84
85         mutex_lock(&dev->lock);
86         if (val)
87                 dev->dat_out[bank] |= bit;
88         else
89                 dev->dat_out[bank] &= ~bit;
90
91         adp5588_gpio_write(dev->client, GPIO_DAT_OUT1 + bank,
92                            dev->dat_out[bank]);
93         mutex_unlock(&dev->lock);
94 }
95
96 static int adp5588_gpio_direction_input(struct gpio_chip *chip, unsigned off)
97 {
98         int ret;
99         unsigned bank;
100         struct adp5588_gpio *dev =
101             container_of(chip, struct adp5588_gpio, gpio_chip);
102
103         bank = ADP5588_BANK(off);
104
105         mutex_lock(&dev->lock);
106         dev->dir[bank] &= ~ADP5588_BIT(off);
107         ret = adp5588_gpio_write(dev->client, GPIO_DIR1 + bank, dev->dir[bank]);
108         mutex_unlock(&dev->lock);
109
110         return ret;
111 }
112
113 static int adp5588_gpio_direction_output(struct gpio_chip *chip,
114                                          unsigned off, int val)
115 {
116         int ret;
117         unsigned bank, bit;
118         struct adp5588_gpio *dev =
119             container_of(chip, struct adp5588_gpio, gpio_chip);
120
121         bank = ADP5588_BANK(off);
122         bit = ADP5588_BIT(off);
123
124         mutex_lock(&dev->lock);
125         dev->dir[bank] |= bit;
126
127         if (val)
128                 dev->dat_out[bank] |= bit;
129         else
130                 dev->dat_out[bank] &= ~bit;
131
132         ret = adp5588_gpio_write(dev->client, GPIO_DAT_OUT1 + bank,
133                                  dev->dat_out[bank]);
134         ret |= adp5588_gpio_write(dev->client, GPIO_DIR1 + bank,
135                                  dev->dir[bank]);
136         mutex_unlock(&dev->lock);
137
138         return ret;
139 }
140
141 #ifdef CONFIG_GPIO_ADP5588_IRQ
142 static int adp5588_gpio_to_irq(struct gpio_chip *chip, unsigned off)
143 {
144         struct adp5588_gpio *dev =
145                 container_of(chip, struct adp5588_gpio, gpio_chip);
146         return dev->irq_base + off;
147 }
148
149 static void adp5588_irq_bus_lock(struct irq_data *d)
150 {
151         struct adp5588_gpio *dev = irq_data_get_irq_chip_data(d);
152
153         mutex_lock(&dev->irq_lock);
154 }
155
156  /*
157   * genirq core code can issue chip->mask/unmask from atomic context.
158   * This doesn't work for slow busses where an access needs to sleep.
159   * bus_sync_unlock() is therefore called outside the atomic context,
160   * syncs the current irq mask state with the slow external controller
161   * and unlocks the bus.
162   */
163
164 static void adp5588_irq_bus_sync_unlock(struct irq_data *d)
165 {
166         struct adp5588_gpio *dev = irq_data_get_irq_chip_data(d);
167         int i;
168
169         for (i = 0; i <= ADP5588_BANK(ADP5588_MAXGPIO); i++)
170                 if (dev->int_en[i] ^ dev->irq_mask[i]) {
171                         dev->int_en[i] = dev->irq_mask[i];
172                         adp5588_gpio_write(dev->client, GPIO_INT_EN1 + i,
173                                            dev->int_en[i]);
174                 }
175
176         mutex_unlock(&dev->irq_lock);
177 }
178
179 static void adp5588_irq_mask(struct irq_data *d)
180 {
181         struct adp5588_gpio *dev = irq_data_get_irq_chip_data(d);
182         unsigned gpio = d->irq - dev->irq_base;
183
184         dev->irq_mask[ADP5588_BANK(gpio)] &= ~ADP5588_BIT(gpio);
185 }
186
187 static void adp5588_irq_unmask(struct irq_data *d)
188 {
189         struct adp5588_gpio *dev = irq_data_get_irq_chip_data(d);
190         unsigned gpio = d->irq - dev->irq_base;
191
192         dev->irq_mask[ADP5588_BANK(gpio)] |= ADP5588_BIT(gpio);
193 }
194
195 static int adp5588_irq_set_type(struct irq_data *d, unsigned int type)
196 {
197         struct adp5588_gpio *dev = irq_data_get_irq_chip_data(d);
198         uint16_t gpio = d->irq - dev->irq_base;
199         unsigned bank, bit;
200
201         if ((type & IRQ_TYPE_EDGE_BOTH)) {
202                 dev_err(&dev->client->dev, "irq %d: unsupported type %d\n",
203                         d->irq, type);
204                 return -EINVAL;
205         }
206
207         bank = ADP5588_BANK(gpio);
208         bit = ADP5588_BIT(gpio);
209
210         if (type & IRQ_TYPE_LEVEL_HIGH)
211                 dev->int_lvl[bank] |= bit;
212         else if (type & IRQ_TYPE_LEVEL_LOW)
213                 dev->int_lvl[bank] &= ~bit;
214         else
215                 return -EINVAL;
216
217         adp5588_gpio_direction_input(&dev->gpio_chip, gpio);
218         adp5588_gpio_write(dev->client, GPIO_INT_LVL1 + bank,
219                            dev->int_lvl[bank]);
220
221         return 0;
222 }
223
224 static struct irq_chip adp5588_irq_chip = {
225         .name                   = "adp5588",
226         .irq_mask               = adp5588_irq_mask,
227         .irq_unmask             = adp5588_irq_unmask,
228         .irq_bus_lock           = adp5588_irq_bus_lock,
229         .irq_bus_sync_unlock    = adp5588_irq_bus_sync_unlock,
230         .irq_set_type           = adp5588_irq_set_type,
231 };
232
233 static int adp5588_gpio_read_intstat(struct i2c_client *client, u8 *buf)
234 {
235         int ret = i2c_smbus_read_i2c_block_data(client, GPIO_INT_STAT1, 3, buf);
236
237         if (ret < 0)
238                 dev_err(&client->dev, "Read INT_STAT Error\n");
239
240         return ret;
241 }
242
243 static irqreturn_t adp5588_irq_handler(int irq, void *devid)
244 {
245         struct adp5588_gpio *dev = devid;
246         unsigned status, bank, bit, pending;
247         int ret;
248         status = adp5588_gpio_read(dev->client, INT_STAT);
249
250         if (status & ADP5588_GPI_INT) {
251                 ret = adp5588_gpio_read_intstat(dev->client, dev->irq_stat);
252                 if (ret < 0)
253                         memset(dev->irq_stat, 0, ARRAY_SIZE(dev->irq_stat));
254
255                 for (bank = 0; bank <= ADP5588_BANK(ADP5588_MAXGPIO);
256                         bank++, bit = 0) {
257                         pending = dev->irq_stat[bank] & dev->irq_mask[bank];
258
259                         while (pending) {
260                                 if (pending & (1 << bit)) {
261                                         handle_nested_irq(dev->irq_base +
262                                                           (bank << 3) + bit);
263                                         pending &= ~(1 << bit);
264
265                                 }
266                                 bit++;
267                         }
268                 }
269         }
270
271         adp5588_gpio_write(dev->client, INT_STAT, status); /* Status is W1C */
272
273         return IRQ_HANDLED;
274 }
275
276 static int adp5588_irq_setup(struct adp5588_gpio *dev)
277 {
278         struct i2c_client *client = dev->client;
279         struct adp5588_gpio_platform_data *pdata = client->dev.platform_data;
280         unsigned gpio;
281         int ret;
282
283         adp5588_gpio_write(client, CFG, ADP5588_AUTO_INC);
284         adp5588_gpio_write(client, INT_STAT, -1); /* status is W1C */
285         adp5588_gpio_read_intstat(client, dev->irq_stat); /* read to clear */
286
287         dev->irq_base = pdata->irq_base;
288         mutex_init(&dev->irq_lock);
289
290         for (gpio = 0; gpio < dev->gpio_chip.ngpio; gpio++) {
291                 int irq = gpio + dev->irq_base;
292                 irq_set_chip_data(irq, dev);
293                 irq_set_chip_and_handler(irq, &adp5588_irq_chip,
294                                          handle_level_irq);
295                 irq_set_nested_thread(irq, 1);
296 #ifdef CONFIG_ARM
297                 /*
298                  * ARM needs us to explicitly flag the IRQ as VALID,
299                  * once we do so, it will also set the noprobe.
300                  */
301                 set_irq_flags(irq, IRQF_VALID);
302 #else
303                 irq_set_noprobe(irq);
304 #endif
305         }
306
307         ret = request_threaded_irq(client->irq,
308                                    NULL,
309                                    adp5588_irq_handler,
310                                    IRQF_TRIGGER_FALLING | IRQF_ONESHOT,
311                                    dev_name(&client->dev), dev);
312         if (ret) {
313                 dev_err(&client->dev, "failed to request irq %d\n",
314                         client->irq);
315                 goto out;
316         }
317
318         dev->gpio_chip.to_irq = adp5588_gpio_to_irq;
319         adp5588_gpio_write(client, CFG,
320                 ADP5588_AUTO_INC | ADP5588_INT_CFG | ADP5588_GPI_INT);
321
322         return 0;
323
324 out:
325         dev->irq_base = 0;
326         return ret;
327 }
328
329 static void adp5588_irq_teardown(struct adp5588_gpio *dev)
330 {
331         if (dev->irq_base)
332                 free_irq(dev->client->irq, dev);
333 }
334
335 #else
336 static int adp5588_irq_setup(struct adp5588_gpio *dev)
337 {
338         struct i2c_client *client = dev->client;
339         dev_warn(&client->dev, "interrupt support not compiled in\n");
340
341         return 0;
342 }
343
344 static void adp5588_irq_teardown(struct adp5588_gpio *dev)
345 {
346 }
347 #endif /* CONFIG_GPIO_ADP5588_IRQ */
348
349 static int __devinit adp5588_gpio_probe(struct i2c_client *client,
350                                         const struct i2c_device_id *id)
351 {
352         struct adp5588_gpio_platform_data *pdata = client->dev.platform_data;
353         struct adp5588_gpio *dev;
354         struct gpio_chip *gc;
355         int ret, i, revid;
356
357         if (pdata == NULL) {
358                 dev_err(&client->dev, "missing platform data\n");
359                 return -ENODEV;
360         }
361
362         if (!i2c_check_functionality(client->adapter,
363                                         I2C_FUNC_SMBUS_BYTE_DATA)) {
364                 dev_err(&client->dev, "SMBUS Byte Data not Supported\n");
365                 return -EIO;
366         }
367
368         dev = kzalloc(sizeof(*dev), GFP_KERNEL);
369         if (dev == NULL) {
370                 dev_err(&client->dev, "failed to alloc memory\n");
371                 return -ENOMEM;
372         }
373
374         dev->client = client;
375
376         gc = &dev->gpio_chip;
377         gc->direction_input = adp5588_gpio_direction_input;
378         gc->direction_output = adp5588_gpio_direction_output;
379         gc->get = adp5588_gpio_get_value;
380         gc->set = adp5588_gpio_set_value;
381         gc->can_sleep = 1;
382
383         gc->base = pdata->gpio_start;
384         gc->ngpio = ADP5588_MAXGPIO;
385         gc->label = client->name;
386         gc->owner = THIS_MODULE;
387
388         mutex_init(&dev->lock);
389
390         ret = adp5588_gpio_read(dev->client, DEV_ID);
391         if (ret < 0)
392                 goto err;
393
394         revid = ret & ADP5588_DEVICE_ID_MASK;
395
396         for (i = 0, ret = 0; i <= ADP5588_BANK(ADP5588_MAXGPIO); i++) {
397                 dev->dat_out[i] = adp5588_gpio_read(client, GPIO_DAT_OUT1 + i);
398                 dev->dir[i] = adp5588_gpio_read(client, GPIO_DIR1 + i);
399                 ret |= adp5588_gpio_write(client, KP_GPIO1 + i, 0);
400                 ret |= adp5588_gpio_write(client, GPIO_PULL1 + i,
401                                 (pdata->pullup_dis_mask >> (8 * i)) & 0xFF);
402                 ret |= adp5588_gpio_write(client, GPIO_INT_EN1 + i, 0);
403                 if (ret)
404                         goto err;
405         }
406
407         if (pdata->irq_base) {
408                 if (WA_DELAYED_READOUT_REVID(revid)) {
409                         dev_warn(&client->dev, "GPIO int not supported\n");
410                 } else {
411                         ret = adp5588_irq_setup(dev);
412                         if (ret)
413                                 goto err;
414                 }
415         }
416
417         ret = gpiochip_add(&dev->gpio_chip);
418         if (ret)
419                 goto err_irq;
420
421         dev_info(&client->dev, "gpios %d..%d (IRQ Base %d) on a %s Rev. %d\n",
422                         gc->base, gc->base + gc->ngpio - 1,
423                         pdata->irq_base, client->name, revid);
424
425         if (pdata->setup) {
426                 ret = pdata->setup(client, gc->base, gc->ngpio, pdata->context);
427                 if (ret < 0)
428                         dev_warn(&client->dev, "setup failed, %d\n", ret);
429         }
430
431         i2c_set_clientdata(client, dev);
432
433         return 0;
434
435 err_irq:
436         adp5588_irq_teardown(dev);
437 err:
438         kfree(dev);
439         return ret;
440 }
441
442 static int __devexit adp5588_gpio_remove(struct i2c_client *client)
443 {
444         struct adp5588_gpio_platform_data *pdata = client->dev.platform_data;
445         struct adp5588_gpio *dev = i2c_get_clientdata(client);
446         int ret;
447
448         if (pdata->teardown) {
449                 ret = pdata->teardown(client,
450                                       dev->gpio_chip.base, dev->gpio_chip.ngpio,
451                                       pdata->context);
452                 if (ret < 0) {
453                         dev_err(&client->dev, "teardown failed %d\n", ret);
454                         return ret;
455                 }
456         }
457
458         if (dev->irq_base)
459                 free_irq(dev->client->irq, dev);
460
461         ret = gpiochip_remove(&dev->gpio_chip);
462         if (ret) {
463                 dev_err(&client->dev, "gpiochip_remove failed %d\n", ret);
464                 return ret;
465         }
466
467         kfree(dev);
468         return 0;
469 }
470
471 static const struct i2c_device_id adp5588_gpio_id[] = {
472         {DRV_NAME, 0},
473         {}
474 };
475
476 MODULE_DEVICE_TABLE(i2c, adp5588_gpio_id);
477
478 static struct i2c_driver adp5588_gpio_driver = {
479         .driver = {
480                    .name = DRV_NAME,
481                    },
482         .probe = adp5588_gpio_probe,
483         .remove = __devexit_p(adp5588_gpio_remove),
484         .id_table = adp5588_gpio_id,
485 };
486
487 static int __init adp5588_gpio_init(void)
488 {
489         return i2c_add_driver(&adp5588_gpio_driver);
490 }
491
492 module_init(adp5588_gpio_init);
493
494 static void __exit adp5588_gpio_exit(void)
495 {
496         i2c_del_driver(&adp5588_gpio_driver);
497 }
498
499 module_exit(adp5588_gpio_exit);
500
501 MODULE_AUTHOR("Michael Hennerich <hennerich@blackfin.uclinux.org>");
502 MODULE_DESCRIPTION("GPIO ADP5588 Driver");
503 MODULE_LICENSE("GPL");