arch/blackfin/mach-bf527/boards/ezkit.c

   1 /*
   2  * Copyright 2004-2009 Analog Devices Inc.
   3  *                2005 National ICT Australia (NICTA)
   4  *                      Aidan Williams <aidan@nicta.com.au>
   5  *
   6  * Licensed under the GPL-2 or later.
   7  */
   8
   9 #include <linux/device.h>
  10 #include <linux/platform_device.h>
  11 #include <linux/mtd/mtd.h>
  12 #include <linux/mtd/partitions.h>
  13 #include <linux/mtd/physmap.h>
  14 #include <linux/spi/spi.h>
  15 #include <linux/spi/flash.h>
  16 #include <linux/i2c.h>
  17 #include <linux/irq.h>
  18 #include <linux/interrupt.h>
  19 #include <linux/usb/musb.h>
  20 #include <linux/leds.h>
  21 #include <linux/input.h>
  22 #include <asm/dma.h>
  23 #include <asm/bfin5xx_spi.h>
  24 #include <asm/reboot.h>
  25 #include <asm/nand.h>
  26 #include <asm/portmux.h>
  27 #include <asm/dpmc.h>
  28 #include <linux/spi/ad7877.h>
  29 #include <asm/bfin_sport.h>
  30
  31 /*
  32  * Name the Board for the /proc/cpuinfo
  33  */
  34 #ifdef CONFIG_BFIN527_EZKIT_V2
  35 const char bfin_board_name[] = "ADI BF527-EZKIT V2";
  36 #else
  37 const char bfin_board_name[] = "ADI BF527-EZKIT";
  38 #endif
  39
  40 /*
  41  *  Driver needs to know address, irq and flag pin.
  42  */
  43
  44 #if defined(CONFIG_USB_ISP1760_HCD) || defined(CONFIG_USB_ISP1760_HCD_MODULE)
  45 #include <linux/usb/isp1760.h>
  46 static struct resource bfin_isp1760_resources[] = {
  47         [0] = {
  48                 .start  = 0x203C0000,
  49                 .end    = 0x203C0000 + 0x000fffff,
  50                 .flags  = IORESOURCE_MEM,
  51         },
  52         [1] = {
  53                 .start  = IRQ_PF7,
  54                 .end    = IRQ_PF7,
  55                 .flags  = IORESOURCE_IRQ,
  56         },
  57 };
  58
  59 static struct isp1760_platform_data isp1760_priv = {
  60         .is_isp1761 = 0,
  61         .bus_width_16 = 1,
  62         .port1_otg = 0,
  63         .analog_oc = 0,
  64         .dack_polarity_high = 0,
  65         .dreq_polarity_high = 0,
  66 };
  67
  68 static struct platform_device bfin_isp1760_device = {
  69         .name           = "isp1760",
  70         .id             = 0,
  71         .dev = {
  72                 .platform_data = &isp1760_priv,
  73         },
  74         .num_resources  = ARRAY_SIZE(bfin_isp1760_resources),
  75         .resource       = bfin_isp1760_resources,
  76 };
  77 #endif
  78
  79 #if defined(CONFIG_USB_MUSB_HDRC) || defined(CONFIG_USB_MUSB_HDRC_MODULE)
  80 static struct resource musb_resources[] = {
  81         [0] = {
  82                 .start  = 0xffc03800,
  83                 .end    = 0xffc03cff,
  84                 .flags  = IORESOURCE_MEM,
  85         },
  86         [1] = { /* general IRQ */
  87                 .start  = IRQ_USB_INT0,
  88                 .end    = IRQ_USB_INT0,
  89                 .flags  = IORESOURCE_IRQ | IORESOURCE_IRQ_HIGHLEVEL,
  90                 .name   = "mc"
  91         },
  92         [2] = { /* DMA IRQ */
  93                 .start  = IRQ_USB_DMA,
  94                 .end    = IRQ_USB_DMA,
  95                 .flags  = IORESOURCE_IRQ | IORESOURCE_IRQ_HIGHLEVEL,
  96                 .name   = "dma"
  97         },
  98 };
  99
 100 static struct musb_hdrc_config musb_config = {
 101         .multipoint     = 0,
 102         .dyn_fifo       = 0,
 103         .soft_con       = 1,
 104         .dma            = 1,
 105         .num_eps        = 8,
 106         .dma_channels   = 8,
 107         .gpio_vrsel     = GPIO_PG13,
 108         /* Some custom boards need to be active low, just set it to "0"
 109          * if it is the case.
 110          */
 111         .gpio_vrsel_active      = 1,
 112         .clkin          = 24,           /* musb CLKIN in MHZ */
 113 };
 114
 115 static struct musb_hdrc_platform_data musb_plat = {
 116 #if defined(CONFIG_USB_MUSB_OTG)
 117         .mode           = MUSB_OTG,
 118 #elif defined(CONFIG_USB_MUSB_HDRC_HCD)
 119         .mode           = MUSB_HOST,
 120 #elif defined(CONFIG_USB_GADGET_MUSB_HDRC)
 121         .mode           = MUSB_PERIPHERAL,
 122 #endif
 123         .config         = &musb_config,
 124 };
 125
 126 static u64 musb_dmamask = ~(u32)0;
 127
 128 static struct platform_device musb_device = {
 129         .name           = "musb-blackfin",
 130         .id             = 0,
 131         .dev = {
 132                 .dma_mask               = &musb_dmamask,
 133                 .coherent_dma_mask      = 0xffffffff,
 134                 .platform_data          = &musb_plat,
 135         },
 136         .num_resources  = ARRAY_SIZE(musb_resources),
 137         .resource       = musb_resources,
 138 };
 139 #endif
 140
 141 #if defined(CONFIG_FB_BFIN_T350MCQB) || defined(CONFIG_FB_BFIN_T350MCQB_MODULE)
 142
 143 static struct resource bf52x_t350mcqb_resources[] = {
 144         {
 145                 .start = IRQ_PPI_ERROR,
 146                 .end = IRQ_PPI_ERROR,
 147                 .flags = IORESOURCE_IRQ,
 148         },
 149 };
 150
 151 static struct platform_device bf52x_t350mcqb_device = {
 152         .name           = "bfin-t350mcqb",
 153         .id             = -1,
 154         .num_resources  = ARRAY_SIZE(bf52x_t350mcqb_resources),
 155         .resource       = bf52x_t350mcqb_resources,
 156 };
 157 #endif
 158
 159 #if defined(CONFIG_FB_BFIN_LQ035Q1) || defined(CONFIG_FB_BFIN_LQ035Q1_MODULE)
 160 #include <asm/bfin-lq035q1.h>
 161
 162 static struct bfin_lq035q1fb_disp_info bfin_lq035q1_data = {
 163         .mode = LQ035_NORM | LQ035_RGB | LQ035_RL | LQ035_TB,
 164         .ppi_mode = USE_RGB565_8_BIT_PPI,
 165 };
 166
 167 static struct resource bfin_lq035q1_resources[] = {
 168         {
 169                 .start = IRQ_PPI_ERROR,
 170                 .end = IRQ_PPI_ERROR,
 171                 .flags = IORESOURCE_IRQ,
 172         },
 173 };
 174
 175 static struct platform_device bfin_lq035q1_device = {
 176         .name           = "bfin-lq035q1",
 177         .id             = -1,
 178         .num_resources  = ARRAY_SIZE(bfin_lq035q1_resources),
 179         .resource       = bfin_lq035q1_resources,
 180         .dev            = {
 181                 .platform_data = &bfin_lq035q1_data,
 182         },
 183 };
 184 #endif
 185
 186 #if defined(CONFIG_MTD_PHYSMAP) || defined(CONFIG_MTD_PHYSMAP_MODULE)
 187 static struct mtd_partition ezkit_partitions[] = {
 188         {
 189                 .name       = "bootloader(nor)",
 190                 .size       = 0x40000,
 191                 .offset     = 0,
 192         }, {
 193                 .name       = "linux kernel(nor)",
 194                 .size       = 0x1C0000,
 195                 .offset     = MTDPART_OFS_APPEND,
 196         }, {
 197                 .name       = "file system(nor)",
 198                 .size       = MTDPART_SIZ_FULL,
 199                 .offset     = MTDPART_OFS_APPEND,
 200         }
 201 };
 202
 203 static struct physmap_flash_data ezkit_flash_data = {
 204         .width      = 2,
 205         .parts      = ezkit_partitions,
 206         .nr_parts   = ARRAY_SIZE(ezkit_partitions),
 207 };
 208
 209 static struct resource ezkit_flash_resource = {
 210         .start = 0x20000000,
 211         .end   = 0x203fffff,
 212         .flags = IORESOURCE_MEM,
 213 };
 214
 215 static struct platform_device ezkit_flash_device = {
 216         .name          = "physmap-flash",
 217         .id            = 0,
 218         .dev = {
 219                 .platform_data = &ezkit_flash_data,
 220         },
 221         .num_resources = 1,
 222         .resource      = &ezkit_flash_resource,
 223 };
 224 #endif
 225
 226 #if defined(CONFIG_MTD_NAND_BF5XX) || defined(CONFIG_MTD_NAND_BF5XX_MODULE)
 227 static struct mtd_partition partition_info[] = {
 228         {
 229                 .name = "bootloader(nand)",
 230                 .offset = 0,
 231                 .size = 0x40000,
 232         }, {
 233                 .name = "linux kernel(nand)",
 234                 .offset = MTDPART_OFS_APPEND,
 235                 .size = 4 * 1024 * 1024,
 236         },
 237         {
 238                 .name = "file system(nand)",
 239                 .offset = MTDPART_OFS_APPEND,
 240                 .size = MTDPART_SIZ_FULL,
 241         },
 242 };
 243
 244 static struct bf5xx_nand_platform bf5xx_nand_platform = {
 245         .data_width = NFC_NWIDTH_8,
 246         .partitions = partition_info,
 247         .nr_partitions = ARRAY_SIZE(partition_info),
 248         .rd_dly = 3,
 249         .wr_dly = 3,
 250 };
 251
 252 static struct resource bf5xx_nand_resources[] = {
 253         {
 254                 .start = NFC_CTL,
 255                 .end = NFC_DATA_RD + 2,
 256                 .flags = IORESOURCE_MEM,
 257         },
 258         {
 259                 .start = CH_NFC,
 260                 .end = CH_NFC,
 261                 .flags = IORESOURCE_IRQ,
 262         },
 263 };
 264
 265 static struct platform_device bf5xx_nand_device = {
 266         .name = "bf5xx-nand",
 267         .id = 0,
 268         .num_resources = ARRAY_SIZE(bf5xx_nand_resources),
 269         .resource = bf5xx_nand_resources,
 270         .dev = {
 271                 .platform_data = &bf5xx_nand_platform,
 272         },
 273 };
 274 #endif
 275
 276 #if defined(CONFIG_BFIN_CFPCMCIA) || defined(CONFIG_BFIN_CFPCMCIA_MODULE)
 277 static struct resource bfin_pcmcia_cf_resources[] = {
 278         {
 279                 .start = 0x20310000, /* IO PORT */
 280                 .end = 0x20312000,
 281                 .flags = IORESOURCE_MEM,
 282         }, {
 283                 .start = 0x20311000, /* Attribute Memory */
 284                 .end = 0x20311FFF,
 285                 .flags = IORESOURCE_MEM,
 286         }, {
 287                 .start = IRQ_PF4,
 288                 .end = IRQ_PF4,
 289                 .flags = IORESOURCE_IRQ | IORESOURCE_IRQ_LOWLEVEL,
 290         }, {
 291                 .start = 6, /* Card Detect PF6 */
 292                 .end = 6,
 293                 .flags = IORESOURCE_IRQ,
 294         },
 295 };
 296
 297 static struct platform_device bfin_pcmcia_cf_device = {
 298         .name = "bfin_cf_pcmcia",
 299         .id = -1,
 300         .num_resources = ARRAY_SIZE(bfin_pcmcia_cf_resources),
 301         .resource = bfin_pcmcia_cf_resources,
 302 };
 303 #endif
 304
 305 #if defined(CONFIG_RTC_DRV_BFIN) || defined(CONFIG_RTC_DRV_BFIN_MODULE)
 306 static struct platform_device rtc_device = {
 307         .name = "rtc-bfin",
 308         .id   = -1,
 309 };
 310 #endif
 311
 312 #if defined(CONFIG_SMC91X) || defined(CONFIG_SMC91X_MODULE)
 313 #include <linux/smc91x.h>
 314
 315 static struct smc91x_platdata smc91x_info = {
 316         .flags = SMC91X_USE_16BIT | SMC91X_NOWAIT,
 317         .leda = RPC_LED_100_10,
 318         .ledb = RPC_LED_TX_RX,
 319 };
 320
 321 static struct resource smc91x_resources[] = {
 322         {
 323                 .name = "smc91x-regs",
 324                 .start = 0x20300300,
 325                 .end = 0x20300300 + 16,
 326                 .flags = IORESOURCE_MEM,
 327         }, {
 328
 329                 .start = IRQ_PF7,
 330                 .end = IRQ_PF7,
 331                 .flags = IORESOURCE_IRQ | IORESOURCE_IRQ_HIGHLEVEL,
 332         },
 333 };
 334 static struct platform_device smc91x_device = {
 335         .name = "smc91x",
 336         .id = 0,
 337         .num_resources = ARRAY_SIZE(smc91x_resources),
 338         .resource = smc91x_resources,
 339         .dev    = {
 340                 .platform_data  = &smc91x_info,
 341         },
 342 };
 343 #endif
 344
 345 #if defined(CONFIG_DM9000) || defined(CONFIG_DM9000_MODULE)
 346 static struct resource dm9000_resources[] = {
 347         [0] = {
 348                 .start  = 0x203FB800,
 349                 .end    = 0x203FB800 + 1,
 350                 .flags  = IORESOURCE_MEM,
 351         },
 352         [1] = {
 353                 .start  = 0x203FB800 + 4,
 354                 .end    = 0x203FB800 + 5,
 355                 .flags  = IORESOURCE_MEM,
 356         },
 357         [2] = {
 358                 .start  = IRQ_PF9,
 359                 .end    = IRQ_PF9,
 360                 .flags  = (IORESOURCE_IRQ | IORESOURCE_IRQ_HIGHEDGE),
 361         },
 362 };
 363
 364 static struct platform_device dm9000_device = {
 365         .name           = "dm9000",
 366         .id             = -1,
 367         .num_resources  = ARRAY_SIZE(dm9000_resources),
 368         .resource       = dm9000_resources,
 369 };
 370 #endif
 371
 372 #if defined(CONFIG_BFIN_MAC) || defined(CONFIG_BFIN_MAC_MODULE)
 373 #include <linux/bfin_mac.h>
 374 static const unsigned short bfin_mac_peripherals[] = P_RMII0;
 375
 376 static struct bfin_phydev_platform_data bfin_phydev_data[] = {
 377         {
 378                 .addr = 1,
 379                 .irq = IRQ_MAC_PHYINT,
 380         },
 381 };
 382
 383 static struct bfin_mii_bus_platform_data bfin_mii_bus_data = {
 384         .phydev_number = 1,
 385         .phydev_data = bfin_phydev_data,
 386         .phy_mode = PHY_INTERFACE_MODE_RMII,
 387         .mac_peripherals = bfin_mac_peripherals,
 388 };
 389
 390 static struct platform_device bfin_mii_bus = {
 391         .name = "bfin_mii_bus",
 392         .dev = {
 393                 .platform_data = &bfin_mii_bus_data,
 394         }
 395 };
 396
 397 static struct platform_device bfin_mac_device = {
 398         .name = "bfin_mac",
 399         .dev = {
 400                 .platform_data = &bfin_mii_bus,
 401         }
 402 };
 403 #endif
 404
 405 #if defined(CONFIG_USB_NET2272) || defined(CONFIG_USB_NET2272_MODULE)
 406 static struct resource net2272_bfin_resources[] = {
 407         {
 408                 .start = 0x20300000,
 409                 .end = 0x20300000 + 0x100,
 410                 .flags = IORESOURCE_MEM,
 411         }, {
 412                 .start = IRQ_PF7,
 413                 .end = IRQ_PF7,
 414                 .flags = IORESOURCE_IRQ | IORESOURCE_IRQ_HIGHLEVEL,
 415         },
 416 };
 417
 418 static struct platform_device net2272_bfin_device = {
 419         .name = "net2272",
 420         .id = -1,
 421         .num_resources = ARRAY_SIZE(net2272_bfin_resources),
 422         .resource = net2272_bfin_resources,
 423 };
 424 #endif
 425
 426 #if defined(CONFIG_MTD_M25P80) \
 427         || defined(CONFIG_MTD_M25P80_MODULE)
 428 static struct mtd_partition bfin_spi_flash_partitions[] = {
 429         {
 430                 .name = "bootloader(spi)",
 431                 .size = 0x00040000,
 432                 .offset = 0,
 433                 .mask_flags = MTD_CAP_ROM
 434         }, {
 435                 .name = "linux kernel(spi)",
 436                 .size = MTDPART_SIZ_FULL,
 437                 .offset = MTDPART_OFS_APPEND,
 438         }
 439 };
 440
 441 static struct flash_platform_data bfin_spi_flash_data = {
 442         .name = "m25p80",
 443         .parts = bfin_spi_flash_partitions,
 444         .nr_parts = ARRAY_SIZE(bfin_spi_flash_partitions),
 445         .type = "m25p16",
 446 };
 447
 448 /* SPI flash chip (m25p64) */
 449 static struct bfin5xx_spi_chip spi_flash_chip_info = {
 450         .enable_dma = 0,         /* use dma transfer with this chip*/
 451         .bits_per_word = 8,
 452 };
 453 #endif
 454
 455 #if defined(CONFIG_BFIN_SPI_ADC) \
 456         || defined(CONFIG_BFIN_SPI_ADC_MODULE)
 457 /* SPI ADC chip */
 458 static struct bfin5xx_spi_chip spi_adc_chip_info = {
 459         .enable_dma = 1,         /* use dma transfer with this chip*/
 460         .bits_per_word = 16,
 461 };
 462 #endif
 463
 464 #if defined(CONFIG_SND_BF5XX_SOC_AD183X) \
 465         || defined(CONFIG_SND_BF5XX_SOC_AD183X_MODULE)
 466 static struct bfin5xx_spi_chip ad1836_spi_chip_info = {
 467         .enable_dma = 0,
 468         .bits_per_word = 16,
 469 };
 470 #endif
 471
 472 #if defined(CONFIG_MMC_SPI) || defined(CONFIG_MMC_SPI_MODULE)
 473 static struct bfin5xx_spi_chip  mmc_spi_chip_info = {
 474         .enable_dma = 0,
 475         .bits_per_word = 8,
 476 };
 477 #endif
 478
 479 #if defined(CONFIG_TOUCHSCREEN_AD7877) || defined(CONFIG_TOUCHSCREEN_AD7877_MODULE)
 480 static struct bfin5xx_spi_chip spi_ad7877_chip_info = {
 481         .enable_dma = 0,
 482         .bits_per_word = 16,
 483 };
 484
 485 static const struct ad7877_platform_data bfin_ad7877_ts_info = {
 486         .model                  = 7877,
 487         .vref_delay_usecs       = 50,   /* internal, no capacitor */
 488         .x_plate_ohms           = 419,
 489         .y_plate_ohms           = 486,
 490         .pressure_max           = 1000,
 491         .pressure_min           = 0,
 492         .stopacq_polarity       = 1,
 493         .first_conversion_delay = 3,
 494         .acquisition_time       = 1,
 495         .averaging              = 1,
 496         .pen_down_acc_interval  = 1,
 497 };
 498 #endif
 499
 500 #if defined(CONFIG_TOUCHSCREEN_AD7879) || defined(CONFIG_TOUCHSCREEN_AD7879_MODULE)
 501 #include <linux/spi/ad7879.h>
 502 static const struct ad7879_platform_data bfin_ad7879_ts_info = {
 503         .model                  = 7879, /* Model = AD7879 */
 504         .x_plate_ohms           = 620,  /* 620 Ohm from the touch datasheet */
 505         .pressure_max           = 10000,
 506         .pressure_min           = 0,
 507         .first_conversion_delay = 3,    /* wait 512us before do a first conversion */
 508         .acquisition_time       = 1,    /* 4us acquisition time per sample */
 509         .median                 = 2,    /* do 8 measurements */
 510         .averaging              = 1,    /* take the average of 4 middle samples */
 511         .pen_down_acc_interval  = 255,  /* 9.4 ms */
 512         .gpio_export            = 0,    /* Export GPIO to gpiolib */
 513 };
 514 #endif
 515
 516 #if defined(CONFIG_TOUCHSCREEN_AD7879_SPI) || defined(CONFIG_TOUCHSCREEN_AD7879_SPI_MODULE)
 517 static struct bfin5xx_spi_chip spi_ad7879_chip_info = {
 518         .enable_dma = 0,
 519         .bits_per_word = 16,
 520 };
 521 #endif
 522
 523 #if defined(CONFIG_SPI_SPIDEV) || defined(CONFIG_SPI_SPIDEV_MODULE)
 524 static struct bfin5xx_spi_chip spidev_chip_info = {
 525         .enable_dma = 0,
 526         .bits_per_word = 8,
 527 };
 528 #endif
 529
 530 #if defined(CONFIG_SND_BF5XX_I2S) || defined(CONFIG_SND_BF5XX_I2S_MODULE) || \
 531         defined(CONFIG_SND_BF5XX_TDM) || defined(CONFIG_SND_BF5XX_TDM_MODULE)
 532
 533 static const u16 bfin_snd_pin[][7] = {
 534         {P_SPORT0_DTPRI, P_SPORT0_TSCLK, P_SPORT0_RFS,
 535                 P_SPORT0_DRPRI, P_SPORT0_RSCLK, 0, 0},
 536         {P_SPORT1_DTPRI, P_SPORT1_TSCLK, P_SPORT1_RFS,
 537                 P_SPORT1_DRPRI, P_SPORT1_RSCLK, P_SPORT1_TFS, 0},
 538 };
 539
 540 static struct bfin_snd_platform_data bfin_snd_data[] = {
 541         {
 542                 .pin_req = &bfin_snd_pin[0][0],
 543         },
 544         {
 545                 .pin_req = &bfin_snd_pin[1][0],
 546         },
 547 };
 548
 549 #define BFIN_SND_RES(x) \
 550         [x] = { \
 551                 { \
 552                         .start = SPORT##x##_TCR1, \
 553                         .end = SPORT##x##_TCR1, \
 554                         .flags = IORESOURCE_MEM \
 555                 }, \
 556                 { \
 557                         .start = CH_SPORT##x##_RX, \
 558                         .end = CH_SPORT##x##_RX, \
 559                         .flags = IORESOURCE_DMA, \
 560                 }, \
 561                 { \
 562                         .start = CH_SPORT##x##_TX, \
 563                         .end = CH_SPORT##x##_TX, \
 564                         .flags = IORESOURCE_DMA, \
 565                 }, \
 566                 { \
 567                         .start = IRQ_SPORT##x##_ERROR, \
 568                         .end = IRQ_SPORT##x##_ERROR, \
 569                         .flags = IORESOURCE_IRQ, \
 570                 } \
 571         }
 572
 573 static struct resource bfin_snd_resources[][4] = {
 574         BFIN_SND_RES(0),
 575         BFIN_SND_RES(1),
 576 };
 577
 578 static struct platform_device bfin_pcm = {
 579         .name = "bfin-pcm-audio",
 580         .id = -1,
 581 };
 582 #endif
 583
 584 #if defined(CONFIG_SND_BF5XX_I2S) || defined(CONFIG_SND_BF5XX_I2S_MODULE)
 585 static struct platform_device bfin_i2s = {
 586         .name = "bfin-i2s",
 587         .id = CONFIG_SND_BF5XX_SPORT_NUM,
 588         .num_resources = ARRAY_SIZE(bfin_snd_resources[CONFIG_SND_BF5XX_SPORT_NUM]),
 589         .resource = bfin_snd_resources[CONFIG_SND_BF5XX_SPORT_NUM],
 590         .dev = {
 591                 .platform_data = &bfin_snd_data[CONFIG_SND_BF5XX_SPORT_NUM],
 592         },
 593 };
 594 #endif
 595
 596 #if defined(CONFIG_SND_BF5XX_TDM) || defined(CONFIG_SND_BF5XX_TDM_MODULE)
 597 static struct platform_device bfin_tdm = {
 598         .name = "bfin-tdm",
 599         .id = CONFIG_SND_BF5XX_SPORT_NUM,
 600         .num_resources = ARRAY_SIZE(bfin_snd_resources[CONFIG_SND_BF5XX_SPORT_NUM]),
 601         .resource = bfin_snd_resources[CONFIG_SND_BF5XX_SPORT_NUM],
 602         .dev = {
 603                 .platform_data = &bfin_snd_data[CONFIG_SND_BF5XX_SPORT_NUM],
 604         },
 605 };
 606 #endif
 607
 608 #if defined(CONFIG_FB_BFIN_LQ035Q1) || defined(CONFIG_FB_BFIN_LQ035Q1_MODULE)
 609 static struct bfin5xx_spi_chip lq035q1_spi_chip_info = {
 610         .enable_dma     = 0,
 611         .bits_per_word  = 8,
 612 };
 613 #endif
 614
 615 static struct spi_board_info bfin_spi_board_info[] __initdata = {
 616 #if defined(CONFIG_MTD_M25P80) \
 617         || defined(CONFIG_MTD_M25P80_MODULE)
 618         {
 619                 /* the modalias must be the same as spi device driver name */
 620                 .modalias = "m25p80", /* Name of spi_driver for this device */
 621                 .max_speed_hz = 25000000,     /* max spi clock (SCK) speed in HZ */
 622                 .bus_num = 0, /* Framework bus number */
 623                 .chip_select = 1, /* Framework chip select. On STAMP537 it is SPISSEL1*/
 624                 .platform_data = &bfin_spi_flash_data,
 625                 .controller_data = &spi_flash_chip_info,
 626                 .mode = SPI_MODE_3,
 627         },
 628 #endif
 629
 630 #if defined(CONFIG_BFIN_SPI_ADC) \
 631         || defined(CONFIG_BFIN_SPI_ADC_MODULE)
 632         {
 633                 .modalias = "bfin_spi_adc", /* Name of spi_driver for this device */
 634                 .max_speed_hz = 6250000,     /* max spi clock (SCK) speed in HZ */
 635                 .bus_num = 0, /* Framework bus number */
 636                 .chip_select = 1, /* Framework chip select. */
 637                 .platform_data = NULL, /* No spi_driver specific config */
 638                 .controller_data = &spi_adc_chip_info,
 639         },
 640 #endif
 641
 642 #if defined(CONFIG_SND_BF5XX_SOC_AD183X) \
 643         || defined(CONFIG_SND_BF5XX_SOC_AD183X_MODULE)
 644         {
 645                 .modalias = "ad183x",
 646                 .max_speed_hz = 3125000,     /* max spi clock (SCK) speed in HZ */
 647                 .bus_num = 0,
 648                 .chip_select = 4,
 649                 .platform_data = "ad1836",
 650                 .controller_data = &ad1836_spi_chip_info,
 651                 .mode = SPI_MODE_3,
 652         },
 653 #endif
 654 #if defined(CONFIG_MMC_SPI) || defined(CONFIG_MMC_SPI_MODULE)
 655         {
 656                 .modalias = "mmc_spi",
 657                 .max_speed_hz = 20000000,     /* max spi clock (SCK) speed in HZ */
 658                 .bus_num = 0,
 659                 .chip_select = 3,
 660                 .controller_data = &mmc_spi_chip_info,
 661                 .mode = SPI_MODE_0,
 662         },
 663 #endif
 664
 665 #if defined(CONFIG_TOUCHSCREEN_AD7877) || defined(CONFIG_TOUCHSCREEN_AD7877_MODULE)
 666         {
 667                 .modalias               = "ad7877",
 668                 .platform_data          = &bfin_ad7877_ts_info,
 669                 .irq                    = IRQ_PF8,
 670                 .max_speed_hz   = 12500000,     /* max spi clock (SCK) speed in HZ */
 671                 .bus_num        = 0,
 672                 .chip_select  = 2,
 673                 .controller_data = &spi_ad7877_chip_info,
 674         },
 675 #endif
 676 #if defined(CONFIG_TOUCHSCREEN_AD7879_SPI) || defined(CONFIG_TOUCHSCREEN_AD7879_SPI_MODULE)
 677         {
 678                 .modalias = "ad7879",
 679                 .platform_data = &bfin_ad7879_ts_info,
 680                 .irq = IRQ_PF8,
 681                 .max_speed_hz = 5000000,     /* max spi clock (SCK) speed in HZ */
 682                 .bus_num = 0,
 683                 .chip_select = 3,
 684                 .controller_data = &spi_ad7879_chip_info,
 685                 .mode = SPI_CPHA | SPI_CPOL,
 686         },
 687 #endif
 688 #if defined(CONFIG_SPI_SPIDEV) || defined(CONFIG_SPI_SPIDEV_MODULE)
 689         {
 690                 .modalias = "spidev",
 691                 .max_speed_hz = 3125000,     /* max spi clock (SCK) speed in HZ */
 692                 .bus_num = 0,
 693                 .chip_select = 1,
 694                 .controller_data = &spidev_chip_info,
 695         },
 696 #endif
 697 #if defined(CONFIG_FB_BFIN_LQ035Q1) || defined(CONFIG_FB_BFIN_LQ035Q1_MODULE)
 698         {
 699                 .modalias = "bfin-lq035q1-spi",
 700                 .max_speed_hz = 20000000,     /* max spi clock (SCK) speed in HZ */
 701                 .bus_num = 0,
 702                 .chip_select = 7,
 703                 .controller_data = &lq035q1_spi_chip_info,
 704                 .mode = SPI_CPHA | SPI_CPOL,
 705         },
 706 #endif
 707 };
 708
 709 #if defined(CONFIG_SPI_BFIN) || defined(CONFIG_SPI_BFIN_MODULE)
 710 /* SPI controller data */
 711 static struct bfin5xx_spi_master bfin_spi0_info = {
 712         .num_chipselect = 8,
 713         .enable_dma = 1,  /* master has the ability to do dma transfer */
 714         .pin_req = {P_SPI0_SCK, P_SPI0_MISO, P_SPI0_MOSI, 0},
 715 };
 716
 717 /* SPI (0) */
 718 static struct resource bfin_spi0_resource[] = {
 719         [0] = {
 720                 .start = SPI0_REGBASE,
 721                 .end   = SPI0_REGBASE + 0xFF,
 722                 .flags = IORESOURCE_MEM,
 723                 },
 724         [1] = {
 725                 .start = CH_SPI,
 726                 .end   = CH_SPI,
 727                 .flags = IORESOURCE_DMA,
 728         },
 729         [2] = {
 730                 .start = IRQ_SPI,
 731                 .end   = IRQ_SPI,
 732                 .flags = IORESOURCE_IRQ,
 733         },
 734 };
 735
 736 static struct platform_device bfin_spi0_device = {
 737         .name = "bfin-spi",
 738         .id = 0, /* Bus number */
 739         .num_resources = ARRAY_SIZE(bfin_spi0_resource),
 740         .resource = bfin_spi0_resource,
 741         .dev = {
 742                 .platform_data = &bfin_spi0_info, /* Passed to driver */
 743         },
 744 };
 745 #endif  /* spi master and devices */
 746
 747 #if defined(CONFIG_SERIAL_BFIN) || defined(CONFIG_SERIAL_BFIN_MODULE)
 748 #ifdef CONFIG_SERIAL_BFIN_UART0
 749 static struct resource bfin_uart0_resources[] = {
 750         {
 751                 .start = UART0_THR,
 752                 .end = UART0_GCTL+2,
 753                 .flags = IORESOURCE_MEM,
 754         },
 755         {
 756                 .start = IRQ_UART0_RX,
 757                 .end = IRQ_UART0_RX+1,
 758                 .flags = IORESOURCE_IRQ,
 759         },
 760         {
 761                 .start = IRQ_UART0_ERROR,
 762                 .end = IRQ_UART0_ERROR,
 763                 .flags = IORESOURCE_IRQ,
 764         },
 765         {
 766                 .start = CH_UART0_TX,
 767                 .end = CH_UART0_TX,
 768                 .flags = IORESOURCE_DMA,
 769         },
 770         {
 771                 .start = CH_UART0_RX,
 772                 .end = CH_UART0_RX,
 773                 .flags = IORESOURCE_DMA,
 774         },
 775 };
 776
 777 static unsigned short bfin_uart0_peripherals[] = {
 778         P_UART0_TX, P_UART0_RX, 0
 779 };
 780
 781 static struct platform_device bfin_uart0_device = {
 782         .name = "bfin-uart",
 783         .id = 0,
 784         .num_resources = ARRAY_SIZE(bfin_uart0_resources),
 785         .resource = bfin_uart0_resources,
 786         .dev = {
 787                 .platform_data = &bfin_uart0_peripherals, /* Passed to driver */
 788         },
 789 };
 790 #endif
 791 #ifdef CONFIG_SERIAL_BFIN_UART1
 792 static struct resource bfin_uart1_resources[] = {
 793         {
 794                 .start = UART1_THR,
 795                 .end = UART1_GCTL+2,
 796                 .flags = IORESOURCE_MEM,
 797         },
 798         {
 799                 .start = IRQ_UART1_RX,
 800                 .end = IRQ_UART1_RX+1,
 801                 .flags = IORESOURCE_IRQ,
 802         },
 803         {
 804                 .start = IRQ_UART1_ERROR,
 805                 .end = IRQ_UART1_ERROR,
 806                 .flags = IORESOURCE_IRQ,
 807         },
 808         {
 809                 .start = CH_UART1_TX,
 810                 .end = CH_UART1_TX,
 811                 .flags = IORESOURCE_DMA,
 812         },
 813         {
 814                 .start = CH_UART1_RX,
 815                 .end = CH_UART1_RX,
 816                 .flags = IORESOURCE_DMA,
 817         },
 818 #ifdef CONFIG_BFIN_UART1_CTSRTS
 819         {       /* CTS pin */
 820                 .start = GPIO_PF9,
 821                 .end = GPIO_PF9,
 822                 .flags = IORESOURCE_IO,
 823         },
 824         {       /* RTS pin */
 825                 .start = GPIO_PF10,
 826                 .end = GPIO_PF10,
 827                 .flags = IORESOURCE_IO,
 828         },
 829 #endif
 830 };
 831
 832 static unsigned short bfin_uart1_peripherals[] = {
 833         P_UART1_TX, P_UART1_RX, 0
 834 };
 835
 836 static struct platform_device bfin_uart1_device = {
 837         .name = "bfin-uart",
 838         .id = 1,
 839         .num_resources = ARRAY_SIZE(bfin_uart1_resources),
 840         .resource = bfin_uart1_resources,
 841         .dev = {
 842                 .platform_data = &bfin_uart1_peripherals, /* Passed to driver */
 843         },
 844 };
 845 #endif
 846 #endif
 847
 848 #if defined(CONFIG_BFIN_SIR) || defined(CONFIG_BFIN_SIR_MODULE)
 849 #ifdef CONFIG_BFIN_SIR0
 850 static struct resource bfin_sir0_resources[] = {
 851         {
 852                 .start = 0xFFC00400,
 853                 .end = 0xFFC004FF,
 854                 .flags = IORESOURCE_MEM,
 855         },
 856         {
 857                 .start = IRQ_UART0_RX,
 858                 .end = IRQ_UART0_RX+1,
 859                 .flags = IORESOURCE_IRQ,
 860         },
 861         {
 862                 .start = CH_UART0_RX,
 863                 .end = CH_UART0_RX+1,
 864                 .flags = IORESOURCE_DMA,
 865         },
 866 };
 867
 868 static struct platform_device bfin_sir0_device = {
 869         .name = "bfin_sir",
 870         .id = 0,
 871         .num_resources = ARRAY_SIZE(bfin_sir0_resources),
 872         .resource = bfin_sir0_resources,
 873 };
 874 #endif
 875 #ifdef CONFIG_BFIN_SIR1
 876 static struct resource bfin_sir1_resources[] = {
 877         {
 878                 .start = 0xFFC02000,
 879                 .end = 0xFFC020FF,
 880                 .flags = IORESOURCE_MEM,
 881         },
 882         {
 883                 .start = IRQ_UART1_RX,
 884                 .end = IRQ_UART1_RX+1,
 885                 .flags = IORESOURCE_IRQ,
 886         },
 887         {
 888                 .start = CH_UART1_RX,
 889                 .end = CH_UART1_RX+1,
 890                 .flags = IORESOURCE_DMA,
 891         },
 892 };
 893
 894 static struct platform_device bfin_sir1_device = {
 895         .name = "bfin_sir",
 896         .id = 1,
 897         .num_resources = ARRAY_SIZE(bfin_sir1_resources),
 898         .resource = bfin_sir1_resources,
 899 };
 900 #endif
 901 #endif
 902
 903 #if defined(CONFIG_I2C_BLACKFIN_TWI) || defined(CONFIG_I2C_BLACKFIN_TWI_MODULE)
 904 static struct resource bfin_twi0_resource[] = {
 905         [0] = {
 906                 .start = TWI0_REGBASE,
 907                 .end   = TWI0_REGBASE,
 908                 .flags = IORESOURCE_MEM,
 909         },
 910         [1] = {
 911                 .start = IRQ_TWI,
 912                 .end   = IRQ_TWI,
 913                 .flags = IORESOURCE_IRQ,
 914         },
 915 };
 916
 917 static struct platform_device i2c_bfin_twi_device = {
 918         .name = "i2c-bfin-twi",
 919         .id = 0,
 920         .num_resources = ARRAY_SIZE(bfin_twi0_resource),
 921         .resource = bfin_twi0_resource,
 922 };
 923 #endif
 924
 925 #if defined(CONFIG_PMIC_ADP5520) || defined(CONFIG_PMIC_ADP5520_MODULE)
 926 #include <linux/mfd/adp5520.h>
 927
 928         /*
 929          *  ADP5520/5501 LEDs Data
 930          */
 931
 932 static struct led_info adp5520_leds[] = {
 933         {
 934                 .name = "adp5520-led1",
 935                 .default_trigger = "none",
 936                 .flags = FLAG_ID_ADP5520_LED1_ADP5501_LED0 | ADP5520_LED_OFFT_600ms,
 937         },
 938 };
 939
 940 static struct adp5520_leds_platform_data adp5520_leds_data = {
 941         .num_leds = ARRAY_SIZE(adp5520_leds),
 942         .leds = adp5520_leds,
 943         .fade_in = ADP5520_FADE_T_600ms,
 944         .fade_out = ADP5520_FADE_T_600ms,
 945         .led_on_time = ADP5520_LED_ONT_600ms,
 946 };
 947
 948         /*
 949          *  ADP5520 Keypad Data
 950          */
 951
 952 static const unsigned short adp5520_keymap[ADP5520_KEYMAPSIZE] = {
 953         [ADP5520_KEY(3, 3)]     = KEY_1,
 954         [ADP5520_KEY(2, 3)]     = KEY_2,
 955         [ADP5520_KEY(1, 3)]     = KEY_3,
 956         [ADP5520_KEY(0, 3)]     = KEY_UP,
 957         [ADP5520_KEY(3, 2)]     = KEY_4,
 958         [ADP5520_KEY(2, 2)]     = KEY_5,
 959         [ADP5520_KEY(1, 2)]     = KEY_6,
 960         [ADP5520_KEY(0, 2)]     = KEY_DOWN,
 961         [ADP5520_KEY(3, 1)]     = KEY_7,
 962         [ADP5520_KEY(2, 1)]     = KEY_8,
 963         [ADP5520_KEY(1, 1)]     = KEY_9,
 964         [ADP5520_KEY(0, 1)]     = KEY_DOT,
 965         [ADP5520_KEY(3, 0)]     = KEY_BACKSPACE,
 966         [ADP5520_KEY(2, 0)]     = KEY_0,
 967         [ADP5520_KEY(1, 0)]     = KEY_HELP,
 968         [ADP5520_KEY(0, 0)]     = KEY_ENTER,
 969 };
 970
 971 static struct adp5520_keys_platform_data adp5520_keys_data = {
 972         .rows_en_mask   = ADP5520_ROW_R3 | ADP5520_ROW_R2 | ADP5520_ROW_R1 | ADP5520_ROW_R0,
 973         .cols_en_mask   = ADP5520_COL_C3 | ADP5520_COL_C2 | ADP5520_COL_C1 | ADP5520_COL_C0,
 974         .keymap         = adp5520_keymap,
 975         .keymapsize     = ARRAY_SIZE(adp5520_keymap),
 976         .repeat         = 0,
 977 };
 978
 979         /*
 980          *  ADP5520/5501 Multifunction Device Init Data
 981          */
 982
 983 static struct adp5520_platform_data adp5520_pdev_data = {
 984         .leds = &adp5520_leds_data,
 985         .keys = &adp5520_keys_data,
 986 };
 987
 988 #endif
 989
 990 static struct i2c_board_info __initdata bfin_i2c_board_info[] = {
 991 #if defined(CONFIG_BFIN_TWI_LCD) || defined(CONFIG_BFIN_TWI_LCD_MODULE)
 992         {
 993                 I2C_BOARD_INFO("pcf8574_lcd", 0x22),
 994         },
 995 #endif
 996 #if defined(CONFIG_INPUT_PCF8574) || defined(CONFIG_INPUT_PCF8574_MODULE)
 997         {
 998                 I2C_BOARD_INFO("pcf8574_keypad", 0x27),
 999                 .irq = IRQ_PF8,
1000         },
1001 #endif
1002 #if defined(CONFIG_FB_BFIN_7393) || defined(CONFIG_FB_BFIN_7393_MODULE)
1003         {
1004                 I2C_BOARD_INFO("bfin-adv7393", 0x2B),
1005         },
1006 #endif
1007 #if defined(CONFIG_TOUCHSCREEN_AD7879_I2C) || defined(CONFIG_TOUCHSCREEN_AD7879_I2C_MODULE)
1008         {
1009                 I2C_BOARD_INFO("ad7879", 0x2C),
1010                 .irq = IRQ_PF8,
1011                 .platform_data = (void *)&bfin_ad7879_ts_info,
1012         },
1013 #endif
1014 #if defined(CONFIG_PMIC_ADP5520) || defined(CONFIG_PMIC_ADP5520_MODULE)
1015         {
1016                 I2C_BOARD_INFO("pmic-adp5520", 0x32),
1017                 .irq = IRQ_PF9,
1018                 .platform_data = (void *)&adp5520_pdev_data,
1019         },
1020 #endif
1021 #if defined(CONFIG_SND_SOC_SSM2602) || defined(CONFIG_SND_SOC_SSM2602_MODULE)
1022         {
1023                 I2C_BOARD_INFO("ssm2602", 0x1b),
1024         },
1025 #endif
1026 #if defined(CONFIG_BFIN_TWI_LCD) || defined(CONFIG_BFIN_TWI_LCD_MODULE)
1027         {
1028                 I2C_BOARD_INFO("ad5252", 0x2f),
1029         },
1030 #endif
1031 #if defined(CONFIG_SND_SOC_ADAU1373) || defined(CONFIG_SND_SOC_ADAU1373_MODULE)
1032         {
1033                 I2C_BOARD_INFO("adau1373", 0x1A),
1034         },
1035 #endif
1036 };
1037
1038 #if defined(CONFIG_SERIAL_BFIN_SPORT) || defined(CONFIG_SERIAL_BFIN_SPORT_MODULE)
1039 #ifdef CONFIG_SERIAL_BFIN_SPORT0_UART
1040 static struct resource bfin_sport0_uart_resources[] = {
1041         {
1042                 .start = SPORT0_TCR1,
1043                 .end = SPORT0_MRCS3+4,
1044                 .flags = IORESOURCE_MEM,
1045         },
1046         {
1047                 .start = IRQ_SPORT0_RX,
1048                 .end = IRQ_SPORT0_RX+1,
1049                 .flags = IORESOURCE_IRQ,
1050         },
1051         {
1052                 .start = IRQ_SPORT0_ERROR,
1053                 .end = IRQ_SPORT0_ERROR,
1054                 .flags = IORESOURCE_IRQ,
1055         },
1056 };
1057
1058 static unsigned short bfin_sport0_peripherals[] = {
1059         P_SPORT0_TFS, P_SPORT0_DTPRI, P_SPORT0_TSCLK, P_SPORT0_RFS,
1060         P_SPORT0_DRPRI, P_SPORT0_RSCLK, 0
1061 };
1062
1063 static struct platform_device bfin_sport0_uart_device = {
1064         .name = "bfin-sport-uart",
1065         .id = 0,
1066         .num_resources = ARRAY_SIZE(bfin_sport0_uart_resources),
1067         .resource = bfin_sport0_uart_resources,
1068         .dev = {
1069                 .platform_data = &bfin_sport0_peripherals, /* Passed to driver */
1070         },
1071 };
1072 #endif
1073 #ifdef CONFIG_SERIAL_BFIN_SPORT1_UART
1074 static struct resource bfin_sport1_uart_resources[] = {
1075         {
1076                 .start = SPORT1_TCR1,
1077                 .end = SPORT1_MRCS3+4,
1078                 .flags = IORESOURCE_MEM,
1079         },
1080         {
1081                 .start = IRQ_SPORT1_RX,
1082                 .end = IRQ_SPORT1_RX+1,
1083                 .flags = IORESOURCE_IRQ,
1084         },
1085         {
1086                 .start = IRQ_SPORT1_ERROR,
1087                 .end = IRQ_SPORT1_ERROR,
1088                 .flags = IORESOURCE_IRQ,
1089         },
1090 };
1091
1092 static unsigned short bfin_sport1_peripherals[] = {
1093         P_SPORT1_TFS, P_SPORT1_DTPRI, P_SPORT1_TSCLK, P_SPORT1_RFS,
1094         P_SPORT1_DRPRI, P_SPORT1_RSCLK, 0
1095 };
1096
1097 static struct platform_device bfin_sport1_uart_device = {
1098         .name = "bfin-sport-uart",
1099         .id = 1,
1100         .num_resources = ARRAY_SIZE(bfin_sport1_uart_resources),
1101         .resource = bfin_sport1_uart_resources,
1102         .dev = {
1103                 .platform_data = &bfin_sport1_peripherals, /* Passed to driver */
1104         },
1105 };
1106 #endif
1107 #endif
1108
1109 #if defined(CONFIG_KEYBOARD_GPIO) || defined(CONFIG_KEYBOARD_GPIO_MODULE)
1110 #include <linux/gpio_keys.h>
1111
1112 static struct gpio_keys_button bfin_gpio_keys_table[] = {
1113         {BTN_0, GPIO_PG0, 1, "gpio-keys: BTN0"},
1114         {BTN_1, GPIO_PG13, 1, "gpio-keys: BTN1"},
1115 };
1116
1117 static struct gpio_keys_platform_data bfin_gpio_keys_data = {
1118         .buttons        = bfin_gpio_keys_table,
1119         .nbuttons       = ARRAY_SIZE(bfin_gpio_keys_table),
1120 };
1121
1122 static struct platform_device bfin_device_gpiokeys = {
1123         .name      = "gpio-keys",
1124         .dev = {
1125                 .platform_data = &bfin_gpio_keys_data,
1126         },
1127 };
1128 #endif
1129
1130 #if defined(CONFIG_INPUT_BFIN_ROTARY) || defined(CONFIG_INPUT_BFIN_ROTARY_MODULE)
1131 #include <asm/bfin_rotary.h>
1132
1133 static struct bfin_rotary_platform_data bfin_rotary_data = {
1134         /*.rotary_up_key     = KEY_UP,*/
1135         /*.rotary_down_key   = KEY_DOWN,*/
1136         .rotary_rel_code   = REL_WHEEL,
1137         .rotary_button_key = KEY_ENTER,
1138         .debounce          = 10,        /* 0..17 */
1139         .mode              = ROT_QUAD_ENC | ROT_DEBE,
1140 };
1141
1142 static struct resource bfin_rotary_resources[] = {
1143         {
1144                 .start = IRQ_CNT,
1145                 .end = IRQ_CNT,
1146                 .flags = IORESOURCE_IRQ,
1147         },
1148 };
1149
1150 static struct platform_device bfin_rotary_device = {
1151         .name           = "bfin-rotary",
1152         .id             = -1,
1153         .num_resources  = ARRAY_SIZE(bfin_rotary_resources),
1154         .resource       = bfin_rotary_resources,
1155         .dev            = {
1156                 .platform_data = &bfin_rotary_data,
1157         },
1158 };
1159 #endif
1160
1161 static const unsigned int cclk_vlev_datasheet[] =
1162 {
1163         VRPAIR(VLEV_100, 400000000),
1164         VRPAIR(VLEV_105, 426000000),
1165         VRPAIR(VLEV_110, 500000000),
1166         VRPAIR(VLEV_115, 533000000),
1167         VRPAIR(VLEV_120, 600000000),
1168 };
1169
1170 static struct bfin_dpmc_platform_data bfin_dmpc_vreg_data = {
1171         .tuple_tab = cclk_vlev_datasheet,
1172         .tabsize = ARRAY_SIZE(cclk_vlev_datasheet),
1173         .vr_settling_time = 25 /* us */,
1174 };
1175
1176 static struct platform_device bfin_dpmc = {
1177         .name = "bfin dpmc",
1178         .dev = {
1179                 .platform_data = &bfin_dmpc_vreg_data,
1180         },
1181 };
1182
1183 static struct platform_device *stamp_devices[] __initdata = {
1184
1185         &bfin_dpmc,
1186
1187 #if defined(CONFIG_MTD_NAND_BF5XX) || defined(CONFIG_MTD_NAND_BF5XX_MODULE)
1188         &bf5xx_nand_device,
1189 #endif
1190
1191 #if defined(CONFIG_BFIN_CFPCMCIA) || defined(CONFIG_BFIN_CFPCMCIA_MODULE)
1192         &bfin_pcmcia_cf_device,
1193 #endif
1194
1195 #if defined(CONFIG_RTC_DRV_BFIN) || defined(CONFIG_RTC_DRV_BFIN_MODULE)
1196         &rtc_device,
1197 #endif
1198
1199 #if defined(CONFIG_USB_ISP1760_HCD) || defined(CONFIG_USB_ISP1760_HCD_MODULE)
1200         &bfin_isp1760_device,
1201 #endif
1202
1203 #if defined(CONFIG_USB_MUSB_HDRC) || defined(CONFIG_USB_MUSB_HDRC_MODULE)
1204         &musb_device,
1205 #endif
1206
1207 #if defined(CONFIG_SMC91X) || defined(CONFIG_SMC91X_MODULE)
1208         &smc91x_device,
1209 #endif
1210
1211 #if defined(CONFIG_DM9000) || defined(CONFIG_DM9000_MODULE)
1212         &dm9000_device,
1213 #endif
1214
1215 #if defined(CONFIG_BFIN_MAC) || defined(CONFIG_BFIN_MAC_MODULE)
1216         &bfin_mii_bus,
1217         &bfin_mac_device,
1218 #endif
1219
1220 #if defined(CONFIG_USB_NET2272) || defined(CONFIG_USB_NET2272_MODULE)
1221         &net2272_bfin_device,
1222 #endif
1223
1224 #if defined(CONFIG_SPI_BFIN) || defined(CONFIG_SPI_BFIN_MODULE)
1225         &bfin_spi0_device,
1226 #endif
1227
1228 #if defined(CONFIG_FB_BFIN_T350MCQB) || defined(CONFIG_FB_BFIN_T350MCQB_MODULE)
1229         &bf52x_t350mcqb_device,
1230 #endif
1231
1232 #if defined(CONFIG_FB_BFIN_LQ035Q1) || defined(CONFIG_FB_BFIN_LQ035Q1_MODULE)
1233         &bfin_lq035q1_device,
1234 #endif
1235
1236 #if defined(CONFIG_SERIAL_BFIN) || defined(CONFIG_SERIAL_BFIN_MODULE)
1237 #ifdef CONFIG_SERIAL_BFIN_UART0
1238         &bfin_uart0_device,
1239 #endif
1240 #ifdef CONFIG_SERIAL_BFIN_UART1
1241         &bfin_uart1_device,
1242 #endif
1243 #endif
1244
1245 #if defined(CONFIG_BFIN_SIR) || defined(CONFIG_BFIN_SIR_MODULE)
1246 #ifdef CONFIG_BFIN_SIR0
1247         &bfin_sir0_device,
1248 #endif
1249 #ifdef CONFIG_BFIN_SIR1
1250         &bfin_sir1_device,
1251 #endif
1252 #endif
1253
1254 #if defined(CONFIG_I2C_BLACKFIN_TWI) || defined(CONFIG_I2C_BLACKFIN_TWI_MODULE)
1255         &i2c_bfin_twi_device,
1256 #endif
1257
1258 #if defined(CONFIG_SERIAL_BFIN_SPORT) || defined(CONFIG_SERIAL_BFIN_SPORT_MODULE)
1259 #ifdef CONFIG_SERIAL_BFIN_SPORT0_UART
1260         &bfin_sport0_uart_device,
1261 #endif
1262 #ifdef CONFIG_SERIAL_BFIN_SPORT1_UART
1263         &bfin_sport1_uart_device,
1264 #endif
1265 #endif
1266
1267 #if defined(CONFIG_KEYBOARD_GPIO) || defined(CONFIG_KEYBOARD_GPIO_MODULE)
1268         &bfin_device_gpiokeys,
1269 #endif
1270
1271 #if defined(CONFIG_INPUT_BFIN_ROTARY) || defined(CONFIG_INPUT_BFIN_ROTARY_MODULE)
1272         &bfin_rotary_device,
1273 #endif
1274
1275 #if defined(CONFIG_MTD_PHYSMAP) || defined(CONFIG_MTD_PHYSMAP_MODULE)
1276         &ezkit_flash_device,
1277 #endif
1278
1279 #if defined(CONFIG_SND_BF5XX_I2S) || defined(CONFIG_SND_BF5XX_I2S_MODULE) || \
1280         defined(CONFIG_SND_BF5XX_TDM) || defined(CONFIG_SND_BF5XX_TDM_MODULE)
1281         &bfin_pcm,
1282 #endif
1283
1284 #if defined(CONFIG_SND_BF5XX_I2S) || defined(CONFIG_SND_BF5XX_I2S_MODULE)
1285         &bfin_i2s,
1286 #endif
1287
1288 #if defined(CONFIG_SND_BF5XX_TDM) || defined(CONFIG_SND_BF5XX_TDM_MODULE)
1289         &bfin_tdm,
1290 #endif
1291 };
1292
1293 static int __init ezkit_init(void)
1294 {
1295         printk(KERN_INFO "%s(): registering device resources\n", __func__);
1296         i2c_register_board_info(0, bfin_i2c_board_info,
1297                                 ARRAY_SIZE(bfin_i2c_board_info));
1298         platform_add_devices(stamp_devices, ARRAY_SIZE(stamp_devices));
1299         spi_register_board_info(bfin_spi_board_info, ARRAY_SIZE(bfin_spi_board_info));
1300         return 0;
1301 }
1302
1303 arch_initcall(ezkit_init);
1304
1305 static struct platform_device *ezkit_early_devices[] __initdata = {
1306 #if defined(CONFIG_SERIAL_BFIN_CONSOLE) || defined(CONFIG_EARLY_PRINTK)
1307 #ifdef CONFIG_SERIAL_BFIN_UART0
1308         &bfin_uart0_device,
1309 #endif
1310 #ifdef CONFIG_SERIAL_BFIN_UART1
1311         &bfin_uart1_device,
1312 #endif
1313 #endif
1314
1315 #if defined(CONFIG_SERIAL_BFIN_SPORT_CONSOLE)
1316 #ifdef CONFIG_SERIAL_BFIN_SPORT0_UART
1317         &bfin_sport0_uart_device,
1318 #endif
1319 #ifdef CONFIG_SERIAL_BFIN_SPORT1_UART
1320         &bfin_sport1_uart_device,
1321 #endif
1322 #endif
1323 };
1324
1325 void __init native_machine_early_platform_add_devices(void)
1326 {
1327         printk(KERN_INFO "register early platform devices\n");
1328         early_platform_add_devices(ezkit_early_devices,
1329                 ARRAY_SIZE(ezkit_early_devices));
1330 }
1331
1332 void native_machine_restart(char *cmd)
1333 {
1334         /* workaround reboot hang when booting from SPI */
1335         if ((bfin_read_SYSCR() & 0x7) == 0x3)
1336                 bfin_reset_boot_spi_cs(P_DEFAULT_BOOT_SPI_CS);
1337 }
1338
1339 void bfin_get_ether_addr(char *addr)
1340 {
1341         /* the MAC is stored in OTP memory page 0xDF */
1342         u32 ret;
1343         u64 otp_mac;
1344         u32 (*otp_read)(u32 page, u32 flags, u64 *page_content) = (void *)0xEF00001A;
1345
1346         ret = otp_read(0xDF, 0x00, &otp_mac);
1347         if (!(ret & 0x1)) {
1348                 char *otp_mac_p = (char *)&otp_mac;
1349                 for (ret = 0; ret < 6; ++ret)
1350                         addr[ret] = otp_mac_p[5 - ret];
1351         }
1352 }
1353 EXPORT_SYMBOL(bfin_get_ether_addr);