arch/blackfin/mach-bf527/boards/ezkit.c

   1 /*
   2  * Copyright 2004-2009 Analog Devices Inc.
   3  *                2005 National ICT Australia (NICTA)
   4  *                      Aidan Williams <aidan@nicta.com.au>
   5  *
   6  * Licensed under the GPL-2 or later.
   7  */
   8
   9 #include <linux/device.h>
  10 #include <linux/platform_device.h>
  11 #include <linux/mtd/mtd.h>
  12 #include <linux/mtd/partitions.h>
  13 #include <linux/mtd/physmap.h>
  14 #include <linux/spi/spi.h>
  15 #include <linux/spi/flash.h>
  16 #include <linux/i2c.h>
  17 #include <linux/irq.h>
  18 #include <linux/interrupt.h>
  19 #include <linux/usb/musb.h>
  20 #include <linux/leds.h>
  21 #include <linux/input.h>
  22 #include <asm/dma.h>
  23 #include <asm/bfin5xx_spi.h>
  24 #include <asm/reboot.h>
  25 #include <asm/nand.h>
  26 #include <asm/portmux.h>
  27 #include <asm/dpmc.h>
  28 #include <linux/spi/ad7877.h>
  29
  30 /*
  31  * Name the Board for the /proc/cpuinfo
  32  */
  33 #ifdef CONFIG_BFIN527_EZKIT_V2
  34 const char bfin_board_name[] = "ADI BF527-EZKIT V2";
  35 #else
  36 const char bfin_board_name[] = "ADI BF527-EZKIT";
  37 #endif
  38
  39 /*
  40  *  Driver needs to know address, irq and flag pin.
  41  */
  42
  43 #if defined(CONFIG_USB_ISP1760_HCD) || defined(CONFIG_USB_ISP1760_HCD_MODULE)
  44 #include <linux/usb/isp1760.h>
  45 static struct resource bfin_isp1760_resources[] = {
  46         [0] = {
  47                 .start  = 0x203C0000,
  48                 .end    = 0x203C0000 + 0x000fffff,
  49                 .flags  = IORESOURCE_MEM,
  50         },
  51         [1] = {
  52                 .start  = IRQ_PF7,
  53                 .end    = IRQ_PF7,
  54                 .flags  = IORESOURCE_IRQ,
  55         },
  56 };
  57
  58 static struct isp1760_platform_data isp1760_priv = {
  59         .is_isp1761 = 0,
  60         .bus_width_16 = 1,
  61         .port1_otg = 0,
  62         .analog_oc = 0,
  63         .dack_polarity_high = 0,
  64         .dreq_polarity_high = 0,
  65 };
  66
  67 static struct platform_device bfin_isp1760_device = {
  68         .name           = "isp1760",
  69         .id             = 0,
  70         .dev = {
  71                 .platform_data = &isp1760_priv,
  72         },
  73         .num_resources  = ARRAY_SIZE(bfin_isp1760_resources),
  74         .resource       = bfin_isp1760_resources,
  75 };
  76 #endif
  77
  78 #if defined(CONFIG_USB_MUSB_HDRC) || defined(CONFIG_USB_MUSB_HDRC_MODULE)
  79 static struct resource musb_resources[] = {
  80         [0] = {
  81                 .start  = 0xffc03800,
  82                 .end    = 0xffc03cff,
  83                 .flags  = IORESOURCE_MEM,
  84         },
  85         [1] = { /* general IRQ */
  86                 .start  = IRQ_USB_INT0,
  87                 .end    = IRQ_USB_INT0,
  88                 .flags  = IORESOURCE_IRQ | IORESOURCE_IRQ_HIGHLEVEL,
  89         },
  90         [2] = { /* DMA IRQ */
  91                 .start  = IRQ_USB_DMA,
  92                 .end    = IRQ_USB_DMA,
  93                 .flags  = IORESOURCE_IRQ | IORESOURCE_IRQ_HIGHLEVEL,
  94         },
  95 };
  96
  97 static struct musb_hdrc_config musb_config = {
  98         .multipoint     = 0,
  99         .dyn_fifo       = 0,
 100         .soft_con       = 1,
 101         .dma            = 1,
 102         .num_eps        = 8,
 103         .dma_channels   = 8,
 104         .gpio_vrsel     = GPIO_PG13,
 105 };
 106
 107 static struct musb_hdrc_platform_data musb_plat = {
 108 #if defined(CONFIG_USB_MUSB_OTG)
 109         .mode           = MUSB_OTG,
 110 #elif defined(CONFIG_USB_MUSB_HDRC_HCD)
 111         .mode           = MUSB_HOST,
 112 #elif defined(CONFIG_USB_GADGET_MUSB_HDRC)
 113         .mode           = MUSB_PERIPHERAL,
 114 #endif
 115         .config         = &musb_config,
 116 };
 117
 118 static u64 musb_dmamask = ~(u32)0;
 119
 120 static struct platform_device musb_device = {
 121         .name           = "musb_hdrc",
 122         .id             = 0,
 123         .dev = {
 124                 .dma_mask               = &musb_dmamask,
 125                 .coherent_dma_mask      = 0xffffffff,
 126                 .platform_data          = &musb_plat,
 127         },
 128         .num_resources  = ARRAY_SIZE(musb_resources),
 129         .resource       = musb_resources,
 130 };
 131 #endif
 132
 133 #if defined(CONFIG_FB_BFIN_T350MCQB) || defined(CONFIG_FB_BFIN_T350MCQB_MODULE)
 134
 135 static struct resource bf52x_t350mcqb_resources[] = {
 136         {
 137                 .start = IRQ_PPI_ERROR,
 138                 .end = IRQ_PPI_ERROR,
 139                 .flags = IORESOURCE_IRQ,
 140         },
 141 };
 142
 143 static struct platform_device bf52x_t350mcqb_device = {
 144         .name           = "bfin-t350mcqb",
 145         .id             = -1,
 146         .num_resources  = ARRAY_SIZE(bf52x_t350mcqb_resources),
 147         .resource       = bf52x_t350mcqb_resources,
 148 };
 149 #endif
 150
 151 #if defined(CONFIG_FB_BFIN_LQ035Q1) || defined(CONFIG_FB_BFIN_LQ035Q1_MODULE)
 152 #include <asm/bfin-lq035q1.h>
 153
 154 static struct bfin_lq035q1fb_disp_info bfin_lq035q1_data = {
 155         .mode = LQ035_NORM | LQ035_RGB | LQ035_RL | LQ035_TB,
 156         .ppi_mode = USE_RGB565_8_BIT_PPI,
 157 };
 158
 159 static struct resource bfin_lq035q1_resources[] = {
 160         {
 161                 .start = IRQ_PPI_ERROR,
 162                 .end = IRQ_PPI_ERROR,
 163                 .flags = IORESOURCE_IRQ,
 164         },
 165 };
 166
 167 static struct platform_device bfin_lq035q1_device = {
 168         .name           = "bfin-lq035q1",
 169         .id             = -1,
 170         .num_resources  = ARRAY_SIZE(bfin_lq035q1_resources),
 171         .resource       = bfin_lq035q1_resources,
 172         .dev            = {
 173                 .platform_data = &bfin_lq035q1_data,
 174         },
 175 };
 176 #endif
 177
 178 #if defined(CONFIG_MTD_PHYSMAP) || defined(CONFIG_MTD_PHYSMAP_MODULE)
 179 static struct mtd_partition ezkit_partitions[] = {
 180         {
 181                 .name       = "bootloader(nor)",
 182                 .size       = 0x40000,
 183                 .offset     = 0,
 184         }, {
 185                 .name       = "linux kernel(nor)",
 186                 .size       = 0x1C0000,
 187                 .offset     = MTDPART_OFS_APPEND,
 188         }, {
 189                 .name       = "file system(nor)",
 190                 .size       = MTDPART_SIZ_FULL,
 191                 .offset     = MTDPART_OFS_APPEND,
 192         }
 193 };
 194
 195 static struct physmap_flash_data ezkit_flash_data = {
 196         .width      = 2,
 197         .parts      = ezkit_partitions,
 198         .nr_parts   = ARRAY_SIZE(ezkit_partitions),
 199 };
 200
 201 static struct resource ezkit_flash_resource = {
 202         .start = 0x20000000,
 203         .end   = 0x203fffff,
 204         .flags = IORESOURCE_MEM,
 205 };
 206
 207 static struct platform_device ezkit_flash_device = {
 208         .name          = "physmap-flash",
 209         .id            = 0,
 210         .dev = {
 211                 .platform_data = &ezkit_flash_data,
 212         },
 213         .num_resources = 1,
 214         .resource      = &ezkit_flash_resource,
 215 };
 216 #endif
 217
 218 #if defined(CONFIG_MTD_NAND_BF5XX) || defined(CONFIG_MTD_NAND_BF5XX_MODULE)
 219 static struct mtd_partition partition_info[] = {
 220         {
 221                 .name = "linux kernel(nand)",
 222                 .offset = 0,
 223                 .size = 4 * 1024 * 1024,
 224         },
 225         {
 226                 .name = "file system(nand)",
 227                 .offset = MTDPART_OFS_APPEND,
 228                 .size = MTDPART_SIZ_FULL,
 229         },
 230 };
 231
 232 static struct bf5xx_nand_platform bf5xx_nand_platform = {
 233         .page_size = NFC_PG_SIZE_256,
 234         .data_width = NFC_NWIDTH_8,
 235         .partitions = partition_info,
 236         .nr_partitions = ARRAY_SIZE(partition_info),
 237         .rd_dly = 3,
 238         .wr_dly = 3,
 239 };
 240
 241 static struct resource bf5xx_nand_resources[] = {
 242         {
 243                 .start = NFC_CTL,
 244                 .end = NFC_DATA_RD + 2,
 245                 .flags = IORESOURCE_MEM,
 246         },
 247         {
 248                 .start = CH_NFC,
 249                 .end = CH_NFC,
 250                 .flags = IORESOURCE_IRQ,
 251         },
 252 };
 253
 254 static struct platform_device bf5xx_nand_device = {
 255         .name = "bf5xx-nand",
 256         .id = 0,
 257         .num_resources = ARRAY_SIZE(bf5xx_nand_resources),
 258         .resource = bf5xx_nand_resources,
 259         .dev = {
 260                 .platform_data = &bf5xx_nand_platform,
 261         },
 262 };
 263 #endif
 264
 265 #if defined(CONFIG_BFIN_CFPCMCIA) || defined(CONFIG_BFIN_CFPCMCIA_MODULE)
 266 static struct resource bfin_pcmcia_cf_resources[] = {
 267         {
 268                 .start = 0x20310000, /* IO PORT */
 269                 .end = 0x20312000,
 270                 .flags = IORESOURCE_MEM,
 271         }, {
 272                 .start = 0x20311000, /* Attribute Memory */
 273                 .end = 0x20311FFF,
 274                 .flags = IORESOURCE_MEM,
 275         }, {
 276                 .start = IRQ_PF4,
 277                 .end = IRQ_PF4,
 278                 .flags = IORESOURCE_IRQ | IORESOURCE_IRQ_LOWLEVEL,
 279         }, {
 280                 .start = 6, /* Card Detect PF6 */
 281                 .end = 6,
 282                 .flags = IORESOURCE_IRQ,
 283         },
 284 };
 285
 286 static struct platform_device bfin_pcmcia_cf_device = {
 287         .name = "bfin_cf_pcmcia",
 288         .id = -1,
 289         .num_resources = ARRAY_SIZE(bfin_pcmcia_cf_resources),
 290         .resource = bfin_pcmcia_cf_resources,
 291 };
 292 #endif
 293
 294 #if defined(CONFIG_RTC_DRV_BFIN) || defined(CONFIG_RTC_DRV_BFIN_MODULE)
 295 static struct platform_device rtc_device = {
 296         .name = "rtc-bfin",
 297         .id   = -1,
 298 };
 299 #endif
 300
 301 #if defined(CONFIG_SMC91X) || defined(CONFIG_SMC91X_MODULE)
 302 #include <linux/smc91x.h>
 303
 304 static struct smc91x_platdata smc91x_info = {
 305         .flags = SMC91X_USE_16BIT | SMC91X_NOWAIT,
 306         .leda = RPC_LED_100_10,
 307         .ledb = RPC_LED_TX_RX,
 308 };
 309
 310 static struct resource smc91x_resources[] = {
 311         {
 312                 .name = "smc91x-regs",
 313                 .start = 0x20300300,
 314                 .end = 0x20300300 + 16,
 315                 .flags = IORESOURCE_MEM,
 316         }, {
 317
 318                 .start = IRQ_PF7,
 319                 .end = IRQ_PF7,
 320                 .flags = IORESOURCE_IRQ | IORESOURCE_IRQ_HIGHLEVEL,
 321         },
 322 };
 323 static struct platform_device smc91x_device = {
 324         .name = "smc91x",
 325         .id = 0,
 326         .num_resources = ARRAY_SIZE(smc91x_resources),
 327         .resource = smc91x_resources,
 328         .dev    = {
 329                 .platform_data  = &smc91x_info,
 330         },
 331 };
 332 #endif
 333
 334 #if defined(CONFIG_DM9000) || defined(CONFIG_DM9000_MODULE)
 335 static struct resource dm9000_resources[] = {
 336         [0] = {
 337                 .start  = 0x203FB800,
 338                 .end    = 0x203FB800 + 1,
 339                 .flags  = IORESOURCE_MEM,
 340         },
 341         [1] = {
 342                 .start  = 0x203FB800 + 4,
 343                 .end    = 0x203FB800 + 5,
 344                 .flags  = IORESOURCE_MEM,
 345         },
 346         [2] = {
 347                 .start  = IRQ_PF9,
 348                 .end    = IRQ_PF9,
 349                 .flags  = (IORESOURCE_IRQ | IORESOURCE_IRQ_HIGHEDGE),
 350         },
 351 };
 352
 353 static struct platform_device dm9000_device = {
 354         .name           = "dm9000",
 355         .id             = -1,
 356         .num_resources  = ARRAY_SIZE(dm9000_resources),
 357         .resource       = dm9000_resources,
 358 };
 359 #endif
 360
 361 #if defined(CONFIG_BFIN_MAC) || defined(CONFIG_BFIN_MAC_MODULE)
 362 static struct platform_device bfin_mii_bus = {
 363         .name = "bfin_mii_bus",
 364 };
 365
 366 static struct platform_device bfin_mac_device = {
 367         .name = "bfin_mac",
 368         .dev.platform_data = &bfin_mii_bus,
 369 };
 370 #endif
 371
 372 #if defined(CONFIG_USB_NET2272) || defined(CONFIG_USB_NET2272_MODULE)
 373 static struct resource net2272_bfin_resources[] = {
 374         {
 375                 .start = 0x20300000,
 376                 .end = 0x20300000 + 0x100,
 377                 .flags = IORESOURCE_MEM,
 378         }, {
 379                 .start = IRQ_PF7,
 380                 .end = IRQ_PF7,
 381                 .flags = IORESOURCE_IRQ | IORESOURCE_IRQ_HIGHLEVEL,
 382         },
 383 };
 384
 385 static struct platform_device net2272_bfin_device = {
 386         .name = "net2272",
 387         .id = -1,
 388         .num_resources = ARRAY_SIZE(net2272_bfin_resources),
 389         .resource = net2272_bfin_resources,
 390 };
 391 #endif
 392
 393 #if defined(CONFIG_MTD_M25P80) \
 394         || defined(CONFIG_MTD_M25P80_MODULE)
 395 static struct mtd_partition bfin_spi_flash_partitions[] = {
 396         {
 397                 .name = "bootloader(spi)",
 398                 .size = 0x00040000,
 399                 .offset = 0,
 400                 .mask_flags = MTD_CAP_ROM
 401         }, {
 402                 .name = "linux kernel(spi)",
 403                 .size = MTDPART_SIZ_FULL,
 404                 .offset = MTDPART_OFS_APPEND,
 405         }
 406 };
 407
 408 static struct flash_platform_data bfin_spi_flash_data = {
 409         .name = "m25p80",
 410         .parts = bfin_spi_flash_partitions,
 411         .nr_parts = ARRAY_SIZE(bfin_spi_flash_partitions),
 412         .type = "m25p16",
 413 };
 414
 415 /* SPI flash chip (m25p64) */
 416 static struct bfin5xx_spi_chip spi_flash_chip_info = {
 417         .enable_dma = 0,         /* use dma transfer with this chip*/
 418         .bits_per_word = 8,
 419 };
 420 #endif
 421
 422 #if defined(CONFIG_BFIN_SPI_ADC) \
 423         || defined(CONFIG_BFIN_SPI_ADC_MODULE)
 424 /* SPI ADC chip */
 425 static struct bfin5xx_spi_chip spi_adc_chip_info = {
 426         .enable_dma = 1,         /* use dma transfer with this chip*/
 427         .bits_per_word = 16,
 428 };
 429 #endif
 430
 431 #if defined(CONFIG_SND_BLACKFIN_AD183X) \
 432         || defined(CONFIG_SND_BLACKFIN_AD183X_MODULE)
 433 static struct bfin5xx_spi_chip ad1836_spi_chip_info = {
 434         .enable_dma = 0,
 435         .bits_per_word = 16,
 436 };
 437 #endif
 438
 439 #if defined(CONFIG_MMC_SPI) || defined(CONFIG_MMC_SPI_MODULE)
 440 static struct bfin5xx_spi_chip  mmc_spi_chip_info = {
 441         .enable_dma = 0,
 442         .bits_per_word = 8,
 443 };
 444 #endif
 445
 446 #if defined(CONFIG_TOUCHSCREEN_AD7877) || defined(CONFIG_TOUCHSCREEN_AD7877_MODULE)
 447 static struct bfin5xx_spi_chip spi_ad7877_chip_info = {
 448         .enable_dma = 0,
 449         .bits_per_word = 16,
 450 };
 451
 452 static const struct ad7877_platform_data bfin_ad7877_ts_info = {
 453         .model                  = 7877,
 454         .vref_delay_usecs       = 50,   /* internal, no capacitor */
 455         .x_plate_ohms           = 419,
 456         .y_plate_ohms           = 486,
 457         .pressure_max           = 1000,
 458         .pressure_min           = 0,
 459         .stopacq_polarity       = 1,
 460         .first_conversion_delay = 3,
 461         .acquisition_time       = 1,
 462         .averaging              = 1,
 463         .pen_down_acc_interval  = 1,
 464 };
 465 #endif
 466
 467 #if defined(CONFIG_TOUCHSCREEN_AD7879) || defined(CONFIG_TOUCHSCREEN_AD7879_MODULE)
 468 #include <linux/spi/ad7879.h>
 469 static const struct ad7879_platform_data bfin_ad7879_ts_info = {
 470         .model                  = 7879, /* Model = AD7879 */
 471         .x_plate_ohms           = 620,  /* 620 Ohm from the touch datasheet */
 472         .pressure_max           = 10000,
 473         .pressure_min           = 0,
 474         .first_conversion_delay = 3,    /* wait 512us before do a first conversion */
 475         .acquisition_time       = 1,    /* 4us acquisition time per sample */
 476         .median                 = 2,    /* do 8 measurements */
 477         .averaging              = 1,    /* take the average of 4 middle samples */
 478         .pen_down_acc_interval  = 255,  /* 9.4 ms */
 479         .gpio_export            = 0,    /* Export GPIO to gpiolib */
 480 };
 481 #endif
 482
 483 #if defined(CONFIG_TOUCHSCREEN_AD7879_SPI) || defined(CONFIG_TOUCHSCREEN_AD7879_SPI_MODULE)
 484 static struct bfin5xx_spi_chip spi_ad7879_chip_info = {
 485         .enable_dma = 0,
 486         .bits_per_word = 16,
 487 };
 488 #endif
 489
 490 #if defined(CONFIG_SPI_SPIDEV) || defined(CONFIG_SPI_SPIDEV_MODULE)
 491 static struct bfin5xx_spi_chip spidev_chip_info = {
 492         .enable_dma = 0,
 493         .bits_per_word = 8,
 494 };
 495 #endif
 496
 497 #if defined(CONFIG_SND_BF5XX_I2S) || defined(CONFIG_SND_BF5XX_I2S_MODULE)
 498 static struct platform_device bfin_i2s = {
 499         .name = "bfin-i2s",
 500         .id = CONFIG_SND_BF5XX_SPORT_NUM,
 501         /* TODO: add platform data here */
 502 };
 503 #endif
 504
 505 #if defined(CONFIG_SND_BF5XX_TDM) || defined(CONFIG_SND_BF5XX_TDM_MODULE)
 506 static struct platform_device bfin_tdm = {
 507         .name = "bfin-tdm",
 508         .id = CONFIG_SND_BF5XX_SPORT_NUM,
 509         /* TODO: add platform data here */
 510 };
 511 #endif
 512
 513 #if defined(CONFIG_FB_BFIN_LQ035Q1) || defined(CONFIG_FB_BFIN_LQ035Q1_MODULE)
 514 static struct bfin5xx_spi_chip lq035q1_spi_chip_info = {
 515         .enable_dma     = 0,
 516         .bits_per_word  = 8,
 517 };
 518 #endif
 519
 520 static struct spi_board_info bfin_spi_board_info[] __initdata = {
 521 #if defined(CONFIG_MTD_M25P80) \
 522         || defined(CONFIG_MTD_M25P80_MODULE)
 523         {
 524                 /* the modalias must be the same as spi device driver name */
 525                 .modalias = "m25p80", /* Name of spi_driver for this device */
 526                 .max_speed_hz = 25000000,     /* max spi clock (SCK) speed in HZ */
 527                 .bus_num = 0, /* Framework bus number */
 528                 .chip_select = 1, /* Framework chip select. On STAMP537 it is SPISSEL1*/
 529                 .platform_data = &bfin_spi_flash_data,
 530                 .controller_data = &spi_flash_chip_info,
 531                 .mode = SPI_MODE_3,
 532         },
 533 #endif
 534
 535 #if defined(CONFIG_BFIN_SPI_ADC) \
 536         || defined(CONFIG_BFIN_SPI_ADC_MODULE)
 537         {
 538                 .modalias = "bfin_spi_adc", /* Name of spi_driver for this device */
 539                 .max_speed_hz = 6250000,     /* max spi clock (SCK) speed in HZ */
 540                 .bus_num = 0, /* Framework bus number */
 541                 .chip_select = 1, /* Framework chip select. */
 542                 .platform_data = NULL, /* No spi_driver specific config */
 543                 .controller_data = &spi_adc_chip_info,
 544         },
 545 #endif
 546
 547 #if defined(CONFIG_SND_BLACKFIN_AD183X) \
 548         || defined(CONFIG_SND_BLACKFIN_AD183X_MODULE)
 549         {
 550                 .modalias = "ad1836",
 551                 .max_speed_hz = 3125000,     /* max spi clock (SCK) speed in HZ */
 552                 .bus_num = 0,
 553                 .chip_select = CONFIG_SND_BLACKFIN_SPI_PFBIT,
 554                 .controller_data = &ad1836_spi_chip_info,
 555         },
 556 #endif
 557 #if defined(CONFIG_MMC_SPI) || defined(CONFIG_MMC_SPI_MODULE)
 558         {
 559                 .modalias = "mmc_spi",
 560                 .max_speed_hz = 20000000,     /* max spi clock (SCK) speed in HZ */
 561                 .bus_num = 0,
 562                 .chip_select = 3,
 563                 .controller_data = &mmc_spi_chip_info,
 564                 .mode = SPI_MODE_0,
 565         },
 566 #endif
 567
 568 #if defined(CONFIG_TOUCHSCREEN_AD7877) || defined(CONFIG_TOUCHSCREEN_AD7877_MODULE)
 569         {
 570                 .modalias               = "ad7877",
 571                 .platform_data          = &bfin_ad7877_ts_info,
 572                 .irq                    = IRQ_PF8,
 573                 .max_speed_hz   = 12500000,     /* max spi clock (SCK) speed in HZ */
 574                 .bus_num        = 0,
 575                 .chip_select  = 2,
 576                 .controller_data = &spi_ad7877_chip_info,
 577         },
 578 #endif
 579 #if defined(CONFIG_TOUCHSCREEN_AD7879_SPI) || defined(CONFIG_TOUCHSCREEN_AD7879_SPI_MODULE)
 580         {
 581                 .modalias = "ad7879",
 582                 .platform_data = &bfin_ad7879_ts_info,
 583                 .irq = IRQ_PF8,
 584                 .max_speed_hz = 5000000,     /* max spi clock (SCK) speed in HZ */
 585                 .bus_num = 0,
 586                 .chip_select = 3,
 587                 .controller_data = &spi_ad7879_chip_info,
 588                 .mode = SPI_CPHA | SPI_CPOL,
 589         },
 590 #endif
 591 #if defined(CONFIG_SPI_SPIDEV) || defined(CONFIG_SPI_SPIDEV_MODULE)
 592         {
 593                 .modalias = "spidev",
 594                 .max_speed_hz = 3125000,     /* max spi clock (SCK) speed in HZ */
 595                 .bus_num = 0,
 596                 .chip_select = 1,
 597                 .controller_data = &spidev_chip_info,
 598         },
 599 #endif
 600 #if defined(CONFIG_FB_BFIN_LQ035Q1) || defined(CONFIG_FB_BFIN_LQ035Q1_MODULE)
 601         {
 602                 .modalias = "bfin-lq035q1-spi",
 603                 .max_speed_hz = 20000000,     /* max spi clock (SCK) speed in HZ */
 604                 .bus_num = 0,
 605                 .chip_select = 7,
 606                 .controller_data = &lq035q1_spi_chip_info,
 607                 .mode = SPI_CPHA | SPI_CPOL,
 608         },
 609 #endif
 610 };
 611
 612 #if defined(CONFIG_SPI_BFIN) || defined(CONFIG_SPI_BFIN_MODULE)
 613 /* SPI controller data */
 614 static struct bfin5xx_spi_master bfin_spi0_info = {
 615         .num_chipselect = 8,
 616         .enable_dma = 1,  /* master has the ability to do dma transfer */
 617         .pin_req = {P_SPI0_SCK, P_SPI0_MISO, P_SPI0_MOSI, 0},
 618 };
 619
 620 /* SPI (0) */
 621 static struct resource bfin_spi0_resource[] = {
 622         [0] = {
 623                 .start = SPI0_REGBASE,
 624                 .end   = SPI0_REGBASE + 0xFF,
 625                 .flags = IORESOURCE_MEM,
 626                 },
 627         [1] = {
 628                 .start = CH_SPI,
 629                 .end   = CH_SPI,
 630                 .flags = IORESOURCE_DMA,
 631         },
 632         [2] = {
 633                 .start = IRQ_SPI,
 634                 .end   = IRQ_SPI,
 635                 .flags = IORESOURCE_IRQ,
 636         },
 637 };
 638
 639 static struct platform_device bfin_spi0_device = {
 640         .name = "bfin-spi",
 641         .id = 0, /* Bus number */
 642         .num_resources = ARRAY_SIZE(bfin_spi0_resource),
 643         .resource = bfin_spi0_resource,
 644         .dev = {
 645                 .platform_data = &bfin_spi0_info, /* Passed to driver */
 646         },
 647 };
 648 #endif  /* spi master and devices */
 649
 650 #if defined(CONFIG_SERIAL_BFIN) || defined(CONFIG_SERIAL_BFIN_MODULE)
 651 #ifdef CONFIG_SERIAL_BFIN_UART0
 652 static struct resource bfin_uart0_resources[] = {
 653         {
 654                 .start = UART0_THR,
 655                 .end = UART0_GCTL+2,
 656                 .flags = IORESOURCE_MEM,
 657         },
 658         {
 659                 .start = IRQ_UART0_RX,
 660                 .end = IRQ_UART0_RX+1,
 661                 .flags = IORESOURCE_IRQ,
 662         },
 663         {
 664                 .start = IRQ_UART0_ERROR,
 665                 .end = IRQ_UART0_ERROR,
 666                 .flags = IORESOURCE_IRQ,
 667         },
 668         {
 669                 .start = CH_UART0_TX,
 670                 .end = CH_UART0_TX,
 671                 .flags = IORESOURCE_DMA,
 672         },
 673         {
 674                 .start = CH_UART0_RX,
 675                 .end = CH_UART0_RX,
 676                 .flags = IORESOURCE_DMA,
 677         },
 678 };
 679
 680 unsigned short bfin_uart0_peripherals[] = {
 681         P_UART0_TX, P_UART0_RX, 0
 682 };
 683
 684 static struct platform_device bfin_uart0_device = {
 685         .name = "bfin-uart",
 686         .id = 0,
 687         .num_resources = ARRAY_SIZE(bfin_uart0_resources),
 688         .resource = bfin_uart0_resources,
 689         .dev = {
 690                 .platform_data = &bfin_uart0_peripherals, /* Passed to driver */
 691         },
 692 };
 693 #endif
 694 #ifdef CONFIG_SERIAL_BFIN_UART1
 695 static struct resource bfin_uart1_resources[] = {
 696         {
 697                 .start = UART1_THR,
 698                 .end = UART1_GCTL+2,
 699                 .flags = IORESOURCE_MEM,
 700         },
 701         {
 702                 .start = IRQ_UART1_RX,
 703                 .end = IRQ_UART1_RX+1,
 704                 .flags = IORESOURCE_IRQ,
 705         },
 706         {
 707                 .start = IRQ_UART1_ERROR,
 708                 .end = IRQ_UART1_ERROR,
 709                 .flags = IORESOURCE_IRQ,
 710         },
 711         {
 712                 .start = CH_UART1_TX,
 713                 .end = CH_UART1_TX,
 714                 .flags = IORESOURCE_DMA,
 715         },
 716         {
 717                 .start = CH_UART1_RX,
 718                 .end = CH_UART1_RX,
 719                 .flags = IORESOURCE_DMA,
 720         },
 721 #ifdef CONFIG_BFIN_UART1_CTSRTS
 722         {       /* CTS pin */
 723                 .start = GPIO_PF9,
 724                 .end = GPIO_PF9,
 725                 .flags = IORESOURCE_IO,
 726         },
 727         {       /* RTS pin */
 728                 .start = GPIO_PF10,
 729                 .end = GPIO_PF10,
 730                 .flags = IORESOURCE_IO,
 731         },
 732 #endif
 733 };
 734
 735 unsigned short bfin_uart1_peripherals[] = {
 736         P_UART1_TX, P_UART1_RX, 0
 737 };
 738
 739 static struct platform_device bfin_uart1_device = {
 740         .name = "bfin-uart",
 741         .id = 1,
 742         .num_resources = ARRAY_SIZE(bfin_uart1_resources),
 743         .resource = bfin_uart1_resources,
 744         .dev = {
 745                 .platform_data = &bfin_uart1_peripherals, /* Passed to driver */
 746         },
 747 };
 748 #endif
 749 #endif
 750
 751 #if defined(CONFIG_BFIN_SIR) || defined(CONFIG_BFIN_SIR_MODULE)
 752 #ifdef CONFIG_BFIN_SIR0
 753 static struct resource bfin_sir0_resources[] = {
 754         {
 755                 .start = 0xFFC00400,
 756                 .end = 0xFFC004FF,
 757                 .flags = IORESOURCE_MEM,
 758         },
 759         {
 760                 .start = IRQ_UART0_RX,
 761                 .end = IRQ_UART0_RX+1,
 762                 .flags = IORESOURCE_IRQ,
 763         },
 764         {
 765                 .start = CH_UART0_RX,
 766                 .end = CH_UART0_RX+1,
 767                 .flags = IORESOURCE_DMA,
 768         },
 769 };
 770
 771 static struct platform_device bfin_sir0_device = {
 772         .name = "bfin_sir",
 773         .id = 0,
 774         .num_resources = ARRAY_SIZE(bfin_sir0_resources),
 775         .resource = bfin_sir0_resources,
 776 };
 777 #endif
 778 #ifdef CONFIG_BFIN_SIR1
 779 static struct resource bfin_sir1_resources[] = {
 780         {
 781                 .start = 0xFFC02000,
 782                 .end = 0xFFC020FF,
 783                 .flags = IORESOURCE_MEM,
 784         },
 785         {
 786                 .start = IRQ_UART1_RX,
 787                 .end = IRQ_UART1_RX+1,
 788                 .flags = IORESOURCE_IRQ,
 789         },
 790         {
 791                 .start = CH_UART1_RX,
 792                 .end = CH_UART1_RX+1,
 793                 .flags = IORESOURCE_DMA,
 794         },
 795 };
 796
 797 static struct platform_device bfin_sir1_device = {
 798         .name = "bfin_sir",
 799         .id = 1,
 800         .num_resources = ARRAY_SIZE(bfin_sir1_resources),
 801         .resource = bfin_sir1_resources,
 802 };
 803 #endif
 804 #endif
 805
 806 #if defined(CONFIG_I2C_BLACKFIN_TWI) || defined(CONFIG_I2C_BLACKFIN_TWI_MODULE)
 807 static struct resource bfin_twi0_resource[] = {
 808         [0] = {
 809                 .start = TWI0_REGBASE,
 810                 .end   = TWI0_REGBASE,
 811                 .flags = IORESOURCE_MEM,
 812         },
 813         [1] = {
 814                 .start = IRQ_TWI,
 815                 .end   = IRQ_TWI,
 816                 .flags = IORESOURCE_IRQ,
 817         },
 818 };
 819
 820 static struct platform_device i2c_bfin_twi_device = {
 821         .name = "i2c-bfin-twi",
 822         .id = 0,
 823         .num_resources = ARRAY_SIZE(bfin_twi0_resource),
 824         .resource = bfin_twi0_resource,
 825 };
 826 #endif
 827
 828 #if defined(CONFIG_PMIC_ADP5520) || defined(CONFIG_PMIC_ADP5520_MODULE)
 829 #include <linux/mfd/adp5520.h>
 830
 831         /*
 832          *  ADP5520/5501 LEDs Data
 833          */
 834
 835 static struct led_info adp5520_leds[] = {
 836         {
 837                 .name = "adp5520-led1",
 838                 .default_trigger = "none",
 839                 .flags = FLAG_ID_ADP5520_LED1_ADP5501_LED0 | ADP5520_LED_OFFT_600ms,
 840         },
 841 };
 842
 843 static struct adp5520_leds_platform_data adp5520_leds_data = {
 844         .num_leds = ARRAY_SIZE(adp5520_leds),
 845         .leds = adp5520_leds,
 846         .fade_in = ADP5520_FADE_T_600ms,
 847         .fade_out = ADP5520_FADE_T_600ms,
 848         .led_on_time = ADP5520_LED_ONT_600ms,
 849 };
 850
 851         /*
 852          *  ADP5520 Keypad Data
 853          */
 854
 855 static const unsigned short adp5520_keymap[ADP5520_KEYMAPSIZE] = {
 856         [ADP5520_KEY(3, 3)]     = KEY_1,
 857         [ADP5520_KEY(2, 3)]     = KEY_2,
 858         [ADP5520_KEY(1, 3)]     = KEY_3,
 859         [ADP5520_KEY(0, 3)]     = KEY_UP,
 860         [ADP5520_KEY(3, 2)]     = KEY_4,
 861         [ADP5520_KEY(2, 2)]     = KEY_5,
 862         [ADP5520_KEY(1, 2)]     = KEY_6,
 863         [ADP5520_KEY(0, 2)]     = KEY_DOWN,
 864         [ADP5520_KEY(3, 1)]     = KEY_7,
 865         [ADP5520_KEY(2, 1)]     = KEY_8,
 866         [ADP5520_KEY(1, 1)]     = KEY_9,
 867         [ADP5520_KEY(0, 1)]     = KEY_DOT,
 868         [ADP5520_KEY(3, 0)]     = KEY_BACKSPACE,
 869         [ADP5520_KEY(2, 0)]     = KEY_0,
 870         [ADP5520_KEY(1, 0)]     = KEY_HELP,
 871         [ADP5520_KEY(0, 0)]     = KEY_ENTER,
 872 };
 873
 874 static struct adp5520_keys_platform_data adp5520_keys_data = {
 875         .rows_en_mask   = ADP5520_ROW_R3 | ADP5520_ROW_R2 | ADP5520_ROW_R1 | ADP5520_ROW_R0,
 876         .cols_en_mask   = ADP5520_COL_C3 | ADP5520_COL_C2 | ADP5520_COL_C1 | ADP5520_COL_C0,
 877         .keymap         = adp5520_keymap,
 878         .keymapsize     = ARRAY_SIZE(adp5520_keymap),
 879         .repeat         = 0,
 880 };
 881
 882         /*
 883          *  ADP5520/5501 Multifuction Device Init Data
 884          */
 885
 886 static struct adp5520_platform_data adp5520_pdev_data = {
 887         .leds = &adp5520_leds_data,
 888         .keys = &adp5520_keys_data,
 889 };
 890
 891 #endif
 892
 893 static struct i2c_board_info __initdata bfin_i2c_board_info[] = {
 894 #if defined(CONFIG_BFIN_TWI_LCD) || defined(CONFIG_BFIN_TWI_LCD_MODULE)
 895         {
 896                 I2C_BOARD_INFO("pcf8574_lcd", 0x22),
 897         },
 898 #endif
 899 #if defined(CONFIG_INPUT_PCF8574) || defined(CONFIG_INPUT_PCF8574_MODULE)
 900         {
 901                 I2C_BOARD_INFO("pcf8574_keypad", 0x27),
 902                 .irq = IRQ_PF8,
 903         },
 904 #endif
 905 #if defined(CONFIG_FB_BFIN_7393) || defined(CONFIG_FB_BFIN_7393_MODULE)
 906         {
 907                 I2C_BOARD_INFO("bfin-adv7393", 0x2B),
 908         },
 909 #endif
 910 #if defined(CONFIG_TOUCHSCREEN_AD7879_I2C) || defined(CONFIG_TOUCHSCREEN_AD7879_I2C_MODULE)
 911         {
 912                 I2C_BOARD_INFO("ad7879", 0x2C),
 913                 .irq = IRQ_PF8,
 914                 .platform_data = (void *)&bfin_ad7879_ts_info,
 915         },
 916 #endif
 917 #if defined(CONFIG_PMIC_ADP5520) || defined(CONFIG_PMIC_ADP5520_MODULE)
 918         {
 919                 I2C_BOARD_INFO("pmic-adp5520", 0x32),
 920                 .irq = IRQ_PF9,
 921                 .platform_data = (void *)&adp5520_pdev_data,
 922         },
 923 #endif
 924 #if defined(CONFIG_SND_SOC_SSM2602) || defined(CONFIG_SND_SOC_SSM2602_MODULE)
 925         {
 926                 I2C_BOARD_INFO("ssm2602", 0x1b),
 927         },
 928 #endif
 929 };
 930
 931 #if defined(CONFIG_SERIAL_BFIN_SPORT) || defined(CONFIG_SERIAL_BFIN_SPORT_MODULE)
 932 #ifdef CONFIG_SERIAL_BFIN_SPORT0_UART
 933 static struct resource bfin_sport0_uart_resources[] = {
 934         {
 935                 .start = SPORT0_TCR1,
 936                 .end = SPORT0_MRCS3+4,
 937                 .flags = IORESOURCE_MEM,
 938         },
 939         {
 940                 .start = IRQ_SPORT0_RX,
 941                 .end = IRQ_SPORT0_RX+1,
 942                 .flags = IORESOURCE_IRQ,
 943         },
 944         {
 945                 .start = IRQ_SPORT0_ERROR,
 946                 .end = IRQ_SPORT0_ERROR,
 947                 .flags = IORESOURCE_IRQ,
 948         },
 949 };
 950
 951 unsigned short bfin_sport0_peripherals[] = {
 952         P_SPORT0_TFS, P_SPORT0_DTPRI, P_SPORT0_TSCLK, P_SPORT0_RFS,
 953         P_SPORT0_DRPRI, P_SPORT0_RSCLK, P_SPORT0_DRSEC, P_SPORT0_DTSEC, 0
 954 };
 955
 956 static struct platform_device bfin_sport0_uart_device = {
 957         .name = "bfin-sport-uart",
 958         .id = 0,
 959         .num_resources = ARRAY_SIZE(bfin_sport0_uart_resources),
 960         .resource = bfin_sport0_uart_resources,
 961         .dev = {
 962                 .platform_data = &bfin_sport0_peripherals, /* Passed to driver */
 963         },
 964 };
 965 #endif
 966 #ifdef CONFIG_SERIAL_BFIN_SPORT1_UART
 967 static struct resource bfin_sport1_uart_resources[] = {
 968         {
 969                 .start = SPORT1_TCR1,
 970                 .end = SPORT1_MRCS3+4,
 971                 .flags = IORESOURCE_MEM,
 972         },
 973         {
 974                 .start = IRQ_SPORT1_RX,
 975                 .end = IRQ_SPORT1_RX+1,
 976                 .flags = IORESOURCE_IRQ,
 977         },
 978         {
 979                 .start = IRQ_SPORT1_ERROR,
 980                 .end = IRQ_SPORT1_ERROR,
 981                 .flags = IORESOURCE_IRQ,
 982         },
 983 };
 984
 985 unsigned short bfin_sport1_peripherals[] = {
 986         P_SPORT1_TFS, P_SPORT1_DTPRI, P_SPORT1_TSCLK, P_SPORT1_RFS,
 987         P_SPORT1_DRPRI, P_SPORT1_RSCLK, P_SPORT1_DRSEC, P_SPORT1_DTSEC, 0
 988 };
 989
 990 static struct platform_device bfin_sport1_uart_device = {
 991         .name = "bfin-sport-uart",
 992         .id = 1,
 993         .num_resources = ARRAY_SIZE(bfin_sport1_uart_resources),
 994         .resource = bfin_sport1_uart_resources,
 995         .dev = {
 996                 .platform_data = &bfin_sport1_peripherals, /* Passed to driver */
 997         },
 998 };
 999 #endif
1000 #endif
1001
1002 #if defined(CONFIG_KEYBOARD_GPIO) || defined(CONFIG_KEYBOARD_GPIO_MODULE)
1003 #include <linux/gpio_keys.h>
1004
1005 static struct gpio_keys_button bfin_gpio_keys_table[] = {
1006         {BTN_0, GPIO_PG0, 1, "gpio-keys: BTN0"},
1007         {BTN_1, GPIO_PG13, 1, "gpio-keys: BTN1"},
1008 };
1009
1010 static struct gpio_keys_platform_data bfin_gpio_keys_data = {
1011         .buttons        = bfin_gpio_keys_table,
1012         .nbuttons       = ARRAY_SIZE(bfin_gpio_keys_table),
1013 };
1014
1015 static struct platform_device bfin_device_gpiokeys = {
1016         .name      = "gpio-keys",
1017         .dev = {
1018                 .platform_data = &bfin_gpio_keys_data,
1019         },
1020 };
1021 #endif
1022
1023 #if defined(CONFIG_INPUT_BFIN_ROTARY) || defined(CONFIG_INPUT_BFIN_ROTARY_MODULE)
1024 #include <asm/bfin_rotary.h>
1025
1026 static struct bfin_rotary_platform_data bfin_rotary_data = {
1027         /*.rotary_up_key     = KEY_UP,*/
1028         /*.rotary_down_key   = KEY_DOWN,*/
1029         .rotary_rel_code   = REL_WHEEL,
1030         .rotary_button_key = KEY_ENTER,
1031         .debounce          = 10,        /* 0..17 */
1032         .mode              = ROT_QUAD_ENC | ROT_DEBE,
1033 };
1034
1035 static struct resource bfin_rotary_resources[] = {
1036         {
1037                 .start = IRQ_CNT,
1038                 .end = IRQ_CNT,
1039                 .flags = IORESOURCE_IRQ,
1040         },
1041 };
1042
1043 static struct platform_device bfin_rotary_device = {
1044         .name           = "bfin-rotary",
1045         .id             = -1,
1046         .num_resources  = ARRAY_SIZE(bfin_rotary_resources),
1047         .resource       = bfin_rotary_resources,
1048         .dev            = {
1049                 .platform_data = &bfin_rotary_data,
1050         },
1051 };
1052 #endif
1053
1054 static const unsigned int cclk_vlev_datasheet[] =
1055 {
1056         VRPAIR(VLEV_100, 400000000),
1057         VRPAIR(VLEV_105, 426000000),
1058         VRPAIR(VLEV_110, 500000000),
1059         VRPAIR(VLEV_115, 533000000),
1060         VRPAIR(VLEV_120, 600000000),
1061 };
1062
1063 static struct bfin_dpmc_platform_data bfin_dmpc_vreg_data = {
1064         .tuple_tab = cclk_vlev_datasheet,
1065         .tabsize = ARRAY_SIZE(cclk_vlev_datasheet),
1066         .vr_settling_time = 25 /* us */,
1067 };
1068
1069 static struct platform_device bfin_dpmc = {
1070         .name = "bfin dpmc",
1071         .dev = {
1072                 .platform_data = &bfin_dmpc_vreg_data,
1073         },
1074 };
1075
1076 static struct platform_device *stamp_devices[] __initdata = {
1077
1078         &bfin_dpmc,
1079
1080 #if defined(CONFIG_MTD_NAND_BF5XX) || defined(CONFIG_MTD_NAND_BF5XX_MODULE)
1081         &bf5xx_nand_device,
1082 #endif
1083
1084 #if defined(CONFIG_BFIN_CFPCMCIA) || defined(CONFIG_BFIN_CFPCMCIA_MODULE)
1085         &bfin_pcmcia_cf_device,
1086 #endif
1087
1088 #if defined(CONFIG_RTC_DRV_BFIN) || defined(CONFIG_RTC_DRV_BFIN_MODULE)
1089         &rtc_device,
1090 #endif
1091
1092 #if defined(CONFIG_USB_ISP1760_HCD) || defined(CONFIG_USB_ISP1760_HCD_MODULE)
1093         &bfin_isp1760_device,
1094 #endif
1095
1096 #if defined(CONFIG_USB_MUSB_HDRC) || defined(CONFIG_USB_MUSB_HDRC_MODULE)
1097         &musb_device,
1098 #endif
1099
1100 #if defined(CONFIG_SMC91X) || defined(CONFIG_SMC91X_MODULE)
1101         &smc91x_device,
1102 #endif
1103
1104 #if defined(CONFIG_DM9000) || defined(CONFIG_DM9000_MODULE)
1105         &dm9000_device,
1106 #endif
1107
1108 #if defined(CONFIG_BFIN_MAC) || defined(CONFIG_BFIN_MAC_MODULE)
1109         &bfin_mii_bus,
1110         &bfin_mac_device,
1111 #endif
1112
1113 #if defined(CONFIG_USB_NET2272) || defined(CONFIG_USB_NET2272_MODULE)
1114         &net2272_bfin_device,
1115 #endif
1116
1117 #if defined(CONFIG_SPI_BFIN) || defined(CONFIG_SPI_BFIN_MODULE)
1118         &bfin_spi0_device,
1119 #endif
1120
1121 #if defined(CONFIG_FB_BFIN_T350MCQB) || defined(CONFIG_FB_BFIN_T350MCQB_MODULE)
1122         &bf52x_t350mcqb_device,
1123 #endif
1124
1125 #if defined(CONFIG_FB_BFIN_LQ035Q1) || defined(CONFIG_FB_BFIN_LQ035Q1_MODULE)
1126         &bfin_lq035q1_device,
1127 #endif
1128
1129 #if defined(CONFIG_SERIAL_BFIN) || defined(CONFIG_SERIAL_BFIN_MODULE)
1130 #ifdef CONFIG_SERIAL_BFIN_UART0
1131         &bfin_uart0_device,
1132 #endif
1133 #ifdef CONFIG_SERIAL_BFIN_UART1
1134         &bfin_uart1_device,
1135 #endif
1136 #endif
1137
1138 #if defined(CONFIG_BFIN_SIR) || defined(CONFIG_BFIN_SIR_MODULE)
1139 #ifdef CONFIG_BFIN_SIR0
1140         &bfin_sir0_device,
1141 #endif
1142 #ifdef CONFIG_BFIN_SIR1
1143         &bfin_sir1_device,
1144 #endif
1145 #endif
1146
1147 #if defined(CONFIG_I2C_BLACKFIN_TWI) || defined(CONFIG_I2C_BLACKFIN_TWI_MODULE)
1148         &i2c_bfin_twi_device,
1149 #endif
1150
1151 #if defined(CONFIG_SERIAL_BFIN_SPORT) || defined(CONFIG_SERIAL_BFIN_SPORT_MODULE)
1152 #ifdef CONFIG_SERIAL_BFIN_SPORT0_UART
1153         &bfin_sport0_uart_device,
1154 #endif
1155 #ifdef CONFIG_SERIAL_BFIN_SPORT1_UART
1156         &bfin_sport1_uart_device,
1157 #endif
1158 #endif
1159
1160 #if defined(CONFIG_KEYBOARD_GPIO) || defined(CONFIG_KEYBOARD_GPIO_MODULE)
1161         &bfin_device_gpiokeys,
1162 #endif
1163
1164 #if defined(CONFIG_INPUT_BFIN_ROTARY) || defined(CONFIG_INPUT_BFIN_ROTARY_MODULE)
1165         &bfin_rotary_device,
1166 #endif
1167
1168 #if defined(CONFIG_MTD_PHYSMAP) || defined(CONFIG_MTD_PHYSMAP_MODULE)
1169         &ezkit_flash_device,
1170 #endif
1171
1172 #if defined(CONFIG_SND_BF5XX_I2S) || defined(CONFIG_SND_BF5XX_I2S_MODULE)
1173         &bfin_i2s,
1174 #endif
1175
1176 #if defined(CONFIG_SND_BF5XX_TDM) || defined(CONFIG_SND_BF5XX_TDM_MODULE)
1177         &bfin_tdm,
1178 #endif
1179 };
1180
1181 static int __init ezkit_init(void)
1182 {
1183         printk(KERN_INFO "%s(): registering device resources\n", __func__);
1184         i2c_register_board_info(0, bfin_i2c_board_info,
1185                                 ARRAY_SIZE(bfin_i2c_board_info));
1186         platform_add_devices(stamp_devices, ARRAY_SIZE(stamp_devices));
1187         spi_register_board_info(bfin_spi_board_info, ARRAY_SIZE(bfin_spi_board_info));
1188         return 0;
1189 }
1190
1191 arch_initcall(ezkit_init);
1192
1193 static struct platform_device *ezkit_early_devices[] __initdata = {
1194 #if defined(CONFIG_SERIAL_BFIN_CONSOLE) || defined(CONFIG_EARLY_PRINTK)
1195 #ifdef CONFIG_SERIAL_BFIN_UART0
1196         &bfin_uart0_device,
1197 #endif
1198 #ifdef CONFIG_SERIAL_BFIN_UART1
1199         &bfin_uart1_device,
1200 #endif
1201 #endif
1202
1203 #if defined(CONFIG_SERIAL_BFIN_SPORT_CONSOLE)
1204 #ifdef CONFIG_SERIAL_BFIN_SPORT0_UART
1205         &bfin_sport0_uart_device,
1206 #endif
1207 #ifdef CONFIG_SERIAL_BFIN_SPORT1_UART
1208         &bfin_sport1_uart_device,
1209 #endif
1210 #endif
1211 };
1212
1213 void __init native_machine_early_platform_add_devices(void)
1214 {
1215         printk(KERN_INFO "register early platform devices\n");
1216         early_platform_add_devices(ezkit_early_devices,
1217                 ARRAY_SIZE(ezkit_early_devices));
1218 }
1219
1220 void native_machine_restart(char *cmd)
1221 {
1222         /* workaround reboot hang when booting from SPI */
1223         if ((bfin_read_SYSCR() & 0x7) == 0x3)
1224                 bfin_reset_boot_spi_cs(P_DEFAULT_BOOT_SPI_CS);
1225 }
1226
1227 void bfin_get_ether_addr(char *addr)
1228 {
1229         /* the MAC is stored in OTP memory page 0xDF */
1230         u32 ret;
1231         u64 otp_mac;
1232         u32 (*otp_read)(u32 page, u32 flags, u64 *page_content) = (void *)0xEF00001A;
1233
1234         ret = otp_read(0xDF, 0x00, &otp_mac);
1235         if (!(ret & 0x1)) {
1236                 char *otp_mac_p = (char *)&otp_mac;
1237                 for (ret = 0; ret < 6; ++ret)
1238                         addr[ret] = otp_mac_p[5 - ret];
1239         }
1240 }
1241 EXPORT_SYMBOL(bfin_get_ether_addr);