arch/arm/mach-pxa/spitz.c

   1 /*
   2  * Support for Sharp SL-Cxx00 Series of PDAs
   3  * Models: SL-C3000 (Spitz), SL-C1000 (Akita) and SL-C3100 (Borzoi)
   4  *
   5  * Copyright (c) 2005 Richard Purdie
   6  *
   7  * Based on Sharp's 2.4 kernel patches/lubbock.c
   8  *
   9  * This program is free software; you can redistribute it and/or modify
  10  * it under the terms of the GNU General Public License version 2 as
  11  * published by the Free Software Foundation.
  12  *
  13  */
  14
  15 #include <linux/kernel.h>
  16 #include <linux/platform_device.h>
  17 #include <linux/delay.h>
  18 #include <linux/gpio_keys.h>
  19 #include <linux/gpio.h>
  20 #include <linux/leds.h>
  21 #include <linux/i2c.h>
  22 #include <linux/i2c/pca953x.h>
  23 #include <linux/spi/spi.h>
  24 #include <linux/spi/ads7846.h>
  25 #include <linux/spi/corgi_lcd.h>
  26 #include <linux/mtd/physmap.h>
  27 #include <linux/mtd/sharpsl.h>
  28 #include <linux/input/matrix_keypad.h>
  29 #include <linux/regulator/machine.h>
  30
  31 #include <asm/setup.h>
  32 #include <asm/mach-types.h>
  33 #include <asm/mach/arch.h>
  34 #include <asm/mach/sharpsl_param.h>
  35 #include <asm/hardware/scoop.h>
  36
  37 #include <mach/pxa27x.h>
  38 #include <mach/pxa27x-udc.h>
  39 #include <mach/reset.h>
  40 #include <mach/irda.h>
  41 #include <mach/mmc.h>
  42 #include <mach/ohci.h>
  43 #include <mach/pxafb.h>
  44 #include <mach/pxa2xx_spi.h>
  45 #include <mach/spitz.h>
  46 #include <mach/sharpsl_pm.h>
  47
  48 #include <plat/i2c.h>
  49
  50 #include "generic.h"
  51 #include "devices.h"
  52
  53 /******************************************************************************
  54  * Pin configuration
  55  ******************************************************************************/
  56 static unsigned long spitz_pin_config[] __initdata = {
  57         /* Chip Selects */
  58         GPIO78_nCS_2,   /* SCOOP #2 */
  59         GPIO79_nCS_3,   /* NAND */
  60         GPIO80_nCS_4,   /* SCOOP #1 */
  61
  62         /* LCD - 16bpp Active TFT */
  63         GPIOxx_LCD_TFT_16BPP,
  64
  65         /* PC Card */
  66         GPIO48_nPOE,
  67         GPIO49_nPWE,
  68         GPIO50_nPIOR,
  69         GPIO51_nPIOW,
  70         GPIO85_nPCE_1,
  71         GPIO54_nPCE_2,
  72         GPIO55_nPREG,
  73         GPIO56_nPWAIT,
  74         GPIO57_nIOIS16,
  75         GPIO104_PSKTSEL,
  76
  77         /* I2S */
  78         GPIO28_I2S_BITCLK_OUT,
  79         GPIO29_I2S_SDATA_IN,
  80         GPIO30_I2S_SDATA_OUT,
  81         GPIO31_I2S_SYNC,
  82
  83         /* MMC */
  84         GPIO32_MMC_CLK,
  85         GPIO112_MMC_CMD,
  86         GPIO92_MMC_DAT_0,
  87         GPIO109_MMC_DAT_1,
  88         GPIO110_MMC_DAT_2,
  89         GPIO111_MMC_DAT_3,
  90
  91         /* GPIOs */
  92         GPIO9_GPIO,     /* SPITZ_GPIO_nSD_DETECT */
  93         GPIO16_GPIO,    /* SPITZ_GPIO_SYNC */
  94         GPIO81_GPIO,    /* SPITZ_GPIO_nSD_WP */
  95         GPIO41_GPIO,    /* SPITZ_GPIO_USB_CONNECT */
  96         GPIO37_GPIO,    /* SPITZ_GPIO_USB_HOST */
  97         GPIO35_GPIO,    /* SPITZ_GPIO_USB_DEVICE */
  98         GPIO22_GPIO,    /* SPITZ_GPIO_HSYNC */
  99         GPIO94_GPIO,    /* SPITZ_GPIO_CF_CD */
 100         GPIO105_GPIO,   /* SPITZ_GPIO_CF_IRQ */
 101         GPIO106_GPIO,   /* SPITZ_GPIO_CF2_IRQ */
 102
 103         /* GPIO matrix keypad */
 104         GPIO88_GPIO,    /* column 0 */
 105         GPIO23_GPIO,    /* column 1 */
 106         GPIO24_GPIO,    /* column 2 */
 107         GPIO25_GPIO,    /* column 3 */
 108         GPIO26_GPIO,    /* column 4 */
 109         GPIO27_GPIO,    /* column 5 */
 110         GPIO52_GPIO,    /* column 6 */
 111         GPIO103_GPIO,   /* column 7 */
 112         GPIO107_GPIO,   /* column 8 */
 113         GPIO108_GPIO,   /* column 9 */
 114         GPIO114_GPIO,   /* column 10 */
 115         GPIO12_GPIO,    /* row 0 */
 116         GPIO17_GPIO,    /* row 1 */
 117         GPIO91_GPIO,    /* row 2 */
 118         GPIO34_GPIO,    /* row 3 */
 119         GPIO36_GPIO,    /* row 4 */
 120         GPIO38_GPIO,    /* row 5 */
 121         GPIO39_GPIO,    /* row 6 */
 122
 123         /* I2C */
 124         GPIO117_I2C_SCL,
 125         GPIO118_I2C_SDA,
 126
 127         GPIO0_GPIO | WAKEUP_ON_EDGE_RISE,       /* SPITZ_GPIO_KEY_INT */
 128         GPIO1_GPIO | WAKEUP_ON_EDGE_FALL,       /* SPITZ_GPIO_RESET */
 129 };
 130
 131
 132 /******************************************************************************
 133  * Scoop GPIO expander
 134  ******************************************************************************/
 135 #if defined(CONFIG_SHARP_SCOOP) || defined(CONFIG_SHARP_SCOOP_MODULE)
 136 /* SCOOP Device #1 */
 137 static struct resource spitz_scoop_1_resources[] = {
 138         [0] = {
 139                 .start          = 0x10800000,
 140                 .end            = 0x10800fff,
 141                 .flags          = IORESOURCE_MEM,
 142         },
 143 };
 144
 145 static struct scoop_config spitz_scoop_1_setup = {
 146         .io_dir         = SPITZ_SCP_IO_DIR,
 147         .io_out         = SPITZ_SCP_IO_OUT,
 148         .suspend_clr    = SPITZ_SCP_SUS_CLR,
 149         .suspend_set    = SPITZ_SCP_SUS_SET,
 150         .gpio_base      = SPITZ_SCP_GPIO_BASE,
 151 };
 152
 153 struct platform_device spitz_scoop_1_device = {
 154         .name           = "sharp-scoop",
 155         .id             = 0,
 156         .dev            = {
 157                 .platform_data  = &spitz_scoop_1_setup,
 158         },
 159         .num_resources  = ARRAY_SIZE(spitz_scoop_1_resources),
 160         .resource       = spitz_scoop_1_resources,
 161 };
 162
 163 /* SCOOP Device #2 */
 164 static struct resource spitz_scoop_2_resources[] = {
 165         [0] = {
 166                 .start          = 0x08800040,
 167                 .end            = 0x08800fff,
 168                 .flags          = IORESOURCE_MEM,
 169         },
 170 };
 171
 172 static struct scoop_config spitz_scoop_2_setup = {
 173         .io_dir         = SPITZ_SCP2_IO_DIR,
 174         .io_out         = SPITZ_SCP2_IO_OUT,
 175         .suspend_clr    = SPITZ_SCP2_SUS_CLR,
 176         .suspend_set    = SPITZ_SCP2_SUS_SET,
 177         .gpio_base      = SPITZ_SCP2_GPIO_BASE,
 178 };
 179
 180 struct platform_device spitz_scoop_2_device = {
 181         .name           = "sharp-scoop",
 182         .id             = 1,
 183         .dev            = {
 184                 .platform_data  = &spitz_scoop_2_setup,
 185         },
 186         .num_resources  = ARRAY_SIZE(spitz_scoop_2_resources),
 187         .resource       = spitz_scoop_2_resources,
 188 };
 189
 190 static void __init spitz_scoop_init(void)
 191 {
 192         platform_device_register(&spitz_scoop_1_device);
 193
 194         /* Akita doesn't have the second SCOOP chip */
 195         if (!machine_is_akita())
 196                 platform_device_register(&spitz_scoop_2_device);
 197 }
 198
 199 /* Power control is shared with between one of the CF slots and SD */
 200 static void spitz_card_pwr_ctrl(uint8_t enable, uint8_t new_cpr)
 201 {
 202         unsigned short cpr;
 203         unsigned long flags;
 204
 205         if (new_cpr & 0x7) {
 206                 gpio_set_value(SPITZ_GPIO_CF_POWER, 1);
 207                 mdelay(5);
 208         }
 209
 210         local_irq_save(flags);
 211
 212         cpr = read_scoop_reg(&spitz_scoop_1_device.dev, SCOOP_CPR);
 213
 214         if (enable & new_cpr)
 215                 cpr |= new_cpr;
 216         else
 217                 cpr &= ~enable;
 218
 219         write_scoop_reg(&spitz_scoop_1_device.dev, SCOOP_CPR, cpr);
 220
 221         local_irq_restore(flags);
 222
 223         if (!(cpr & 0x7)) {
 224                 mdelay(1);
 225                 gpio_set_value(SPITZ_GPIO_CF_POWER, 0);
 226         }
 227 }
 228
 229 #else
 230 static inline void spitz_scoop_init(void) {}
 231 static inline void spitz_card_pwr_ctrl(uint8_t enable, uint8_t new_cpr) {}
 232 #endif
 233
 234 /******************************************************************************
 235  * PCMCIA
 236  ******************************************************************************/
 237 #if defined(CONFIG_PCMCIA_PXA2XX) || defined(CONFIG_PCMCIA_PXA2XX_MODULE)
 238 static void spitz_pcmcia_pwr(struct device *scoop, uint16_t cpr, int nr)
 239 {
 240         /* Only need to override behaviour for slot 0 */
 241         if (nr == 0)
 242                 spitz_card_pwr_ctrl(
 243                         cpr & (SCOOP_CPR_CF_3V | SCOOP_CPR_CF_XV), cpr);
 244         else
 245                 write_scoop_reg(scoop, SCOOP_CPR, cpr);
 246 }
 247
 248 static struct scoop_pcmcia_dev spitz_pcmcia_scoop[] = {
 249         {
 250                 .dev            = &spitz_scoop_1_device.dev,
 251                 .irq            = SPITZ_IRQ_GPIO_CF_IRQ,
 252                 .cd_irq         = SPITZ_IRQ_GPIO_CF_CD,
 253                 .cd_irq_str     = "PCMCIA0 CD",
 254         }, {
 255                 .dev            = &spitz_scoop_2_device.dev,
 256                 .irq            = SPITZ_IRQ_GPIO_CF2_IRQ,
 257                 .cd_irq         = -1,
 258         },
 259 };
 260
 261 static struct scoop_pcmcia_config spitz_pcmcia_config = {
 262         .devs           = &spitz_pcmcia_scoop[0],
 263         .num_devs       = 2,
 264         .power_ctrl     = spitz_pcmcia_pwr,
 265 };
 266
 267 static void __init spitz_pcmcia_init(void)
 268 {
 269         /* Akita has only one PCMCIA slot used */
 270         if (machine_is_akita())
 271                 spitz_pcmcia_config.num_devs = 1;
 272
 273         platform_scoop_config = &spitz_pcmcia_config;
 274 }
 275 #else
 276 static inline void spitz_pcmcia_init(void) {}
 277 #endif
 278
 279 /******************************************************************************
 280  * GPIO keyboard
 281  ******************************************************************************/
 282 #if defined(CONFIG_KEYBOARD_MATRIX) || defined(CONFIG_KEYBOARD_MATRIX_MODULE)
 283
 284 #define SPITZ_KEY_CALENDAR      KEY_F1
 285 #define SPITZ_KEY_ADDRESS       KEY_F2
 286 #define SPITZ_KEY_FN            KEY_F3
 287 #define SPITZ_KEY_CANCEL        KEY_F4
 288 #define SPITZ_KEY_EXOK          KEY_F5
 289 #define SPITZ_KEY_EXCANCEL      KEY_F6
 290 #define SPITZ_KEY_EXJOGDOWN     KEY_F7
 291 #define SPITZ_KEY_EXJOGUP       KEY_F8
 292 #define SPITZ_KEY_JAP1          KEY_LEFTALT
 293 #define SPITZ_KEY_JAP2          KEY_RIGHTCTRL
 294 #define SPITZ_KEY_SYNC          KEY_F9
 295 #define SPITZ_KEY_MAIL          KEY_F10
 296 #define SPITZ_KEY_OK            KEY_F11
 297 #define SPITZ_KEY_MENU          KEY_F12
 298
 299 static const uint32_t spitz_keymap[] = {
 300         KEY(0, 0, KEY_LEFTCTRL),
 301         KEY(0, 1, KEY_1),
 302         KEY(0, 2, KEY_3),
 303         KEY(0, 3, KEY_5),
 304         KEY(0, 4, KEY_6),
 305         KEY(0, 5, KEY_7),
 306         KEY(0, 6, KEY_9),
 307         KEY(0, 7, KEY_0),
 308         KEY(0, 8, KEY_BACKSPACE),
 309         KEY(0, 9, SPITZ_KEY_EXOK),      /* EXOK */
 310         KEY(0, 10, SPITZ_KEY_EXCANCEL), /* EXCANCEL */
 311         KEY(1, 1, KEY_2),
 312         KEY(1, 2, KEY_4),
 313         KEY(1, 3, KEY_R),
 314         KEY(1, 4, KEY_Y),
 315         KEY(1, 5, KEY_8),
 316         KEY(1, 6, KEY_I),
 317         KEY(1, 7, KEY_O),
 318         KEY(1, 8, KEY_P),
 319         KEY(1, 9, SPITZ_KEY_EXJOGDOWN), /* EXJOGDOWN */
 320         KEY(1, 10, SPITZ_KEY_EXJOGUP),  /* EXJOGUP */
 321         KEY(2, 0, KEY_TAB),
 322         KEY(2, 1, KEY_Q),
 323         KEY(2, 2, KEY_E),
 324         KEY(2, 3, KEY_T),
 325         KEY(2, 4, KEY_G),
 326         KEY(2, 5, KEY_U),
 327         KEY(2, 6, KEY_J),
 328         KEY(2, 7, KEY_K),
 329         KEY(3, 0, SPITZ_KEY_ADDRESS),   /* ADDRESS */
 330         KEY(3, 1, KEY_W),
 331         KEY(3, 2, KEY_S),
 332         KEY(3, 3, KEY_F),
 333         KEY(3, 4, KEY_V),
 334         KEY(3, 5, KEY_H),
 335         KEY(3, 6, KEY_M),
 336         KEY(3, 7, KEY_L),
 337         KEY(3, 9, KEY_RIGHTSHIFT),
 338         KEY(4, 0, SPITZ_KEY_CALENDAR),  /* CALENDAR */
 339         KEY(4, 1, KEY_A),
 340         KEY(4, 2, KEY_D),
 341         KEY(4, 3, KEY_C),
 342         KEY(4, 4, KEY_B),
 343         KEY(4, 5, KEY_N),
 344         KEY(4, 6, KEY_DOT),
 345         KEY(4, 8, KEY_ENTER),
 346         KEY(4, 9, KEY_LEFTSHIFT),
 347         KEY(5, 0, SPITZ_KEY_MAIL),      /* MAIL */
 348         KEY(5, 1, KEY_Z),
 349         KEY(5, 2, KEY_X),
 350         KEY(5, 3, KEY_MINUS),
 351         KEY(5, 4, KEY_SPACE),
 352         KEY(5, 5, KEY_COMMA),
 353         KEY(5, 7, KEY_UP),
 354         KEY(5, 10, SPITZ_KEY_FN),       /* FN */
 355         KEY(6, 0, KEY_SYSRQ),
 356         KEY(6, 1, SPITZ_KEY_JAP1),      /* JAP1 */
 357         KEY(6, 2, SPITZ_KEY_JAP2),      /* JAP2 */
 358         KEY(6, 3, SPITZ_KEY_CANCEL),    /* CANCEL */
 359         KEY(6, 4, SPITZ_KEY_OK),        /* OK */
 360         KEY(6, 5, SPITZ_KEY_MENU),      /* MENU */
 361         KEY(6, 6, KEY_LEFT),
 362         KEY(6, 7, KEY_DOWN),
 363         KEY(6, 8, KEY_RIGHT),
 364 };
 365
 366 static const struct matrix_keymap_data spitz_keymap_data = {
 367         .keymap         = spitz_keymap,
 368         .keymap_size    = ARRAY_SIZE(spitz_keymap),
 369 };
 370
 371 static const uint32_t spitz_row_gpios[] =
 372                 { 12, 17, 91, 34, 36, 38, 39 };
 373 static const uint32_t spitz_col_gpios[] =
 374                 { 88, 23, 24, 25, 26, 27, 52, 103, 107, 108, 114 };
 375
 376 static struct matrix_keypad_platform_data spitz_mkp_pdata = {
 377         .keymap_data            = &spitz_keymap_data,
 378         .row_gpios              = spitz_row_gpios,
 379         .col_gpios              = spitz_col_gpios,
 380         .num_row_gpios          = ARRAY_SIZE(spitz_row_gpios),
 381         .num_col_gpios          = ARRAY_SIZE(spitz_col_gpios),
 382         .col_scan_delay_us      = 10,
 383         .debounce_ms            = 10,
 384         .wakeup                 = 1,
 385 };
 386
 387 static struct platform_device spitz_mkp_device = {
 388         .name           = "matrix-keypad",
 389         .id             = -1,
 390         .dev            = {
 391                 .platform_data  = &spitz_mkp_pdata,
 392         },
 393 };
 394
 395 static void __init spitz_mkp_init(void)
 396 {
 397         platform_device_register(&spitz_mkp_device);
 398 }
 399 #else
 400 static inline void spitz_mkp_init(void) {}
 401 #endif
 402
 403 /******************************************************************************
 404  * GPIO keys
 405  ******************************************************************************/
 406 #if defined(CONFIG_KEYBOARD_GPIO) || defined(CONFIG_KEYBOARD_GPIO_MODULE)
 407 static struct gpio_keys_button spitz_gpio_keys[] = {
 408         {
 409                 .type   = EV_PWR,
 410                 .code   = KEY_SUSPEND,
 411                 .gpio   = SPITZ_GPIO_ON_KEY,
 412                 .desc   = "On Off",
 413                 .wakeup = 1,
 414         },
 415         /* Two buttons detecting the lid state */
 416         {
 417                 .type   = EV_SW,
 418                 .code   = 0,
 419                 .gpio   = SPITZ_GPIO_SWA,
 420                 .desc   = "Display Down",
 421         },
 422         {
 423                 .type   = EV_SW,
 424                 .code   = 1,
 425                 .gpio   = SPITZ_GPIO_SWB,
 426                 .desc   = "Lid Closed",
 427         },
 428 };
 429
 430 static struct gpio_keys_platform_data spitz_gpio_keys_platform_data = {
 431         .buttons        = spitz_gpio_keys,
 432         .nbuttons       = ARRAY_SIZE(spitz_gpio_keys),
 433 };
 434
 435 static struct platform_device spitz_gpio_keys_device = {
 436         .name   = "gpio-keys",
 437         .id     = -1,
 438         .dev    = {
 439                 .platform_data  = &spitz_gpio_keys_platform_data,
 440         },
 441 };
 442
 443 static void __init spitz_keys_init(void)
 444 {
 445         platform_device_register(&spitz_gpio_keys_device);
 446 }
 447 #else
 448 static inline void spitz_keys_init(void) {}
 449 #endif
 450
 451 /******************************************************************************
 452  * LEDs
 453  ******************************************************************************/
 454 #if defined(CONFIG_LEDS_GPIO) || defined(CONFIG_LEDS_GPIO_MODULE)
 455 static struct gpio_led spitz_gpio_leds[] = {
 456         {
 457                 .name                   = "spitz:amber:charge",
 458                 .default_trigger        = "sharpsl-charge",
 459                 .gpio                   = SPITZ_GPIO_LED_ORANGE,
 460         },
 461         {
 462                 .name                   = "spitz:green:hddactivity",
 463                 .default_trigger        = "ide-disk",
 464                 .gpio                   = SPITZ_GPIO_LED_GREEN,
 465         },
 466 };
 467
 468 static struct gpio_led_platform_data spitz_gpio_leds_info = {
 469         .leds           = spitz_gpio_leds,
 470         .num_leds       = ARRAY_SIZE(spitz_gpio_leds),
 471 };
 472
 473 static struct platform_device spitz_led_device = {
 474         .name           = "leds-gpio",
 475         .id             = -1,
 476         .dev            = {
 477                 .platform_data  = &spitz_gpio_leds_info,
 478         },
 479 };
 480
 481 static void __init spitz_leds_init(void)
 482 {
 483         platform_device_register(&spitz_led_device);
 484 }
 485 #else
 486 static inline void spitz_leds_init(void) {}
 487 #endif
 488
 489 /******************************************************************************
 490  * SSP Devices
 491  ******************************************************************************/
 492 #if defined(CONFIG_SPI_PXA2XX) || defined(CONFIG_SPI_PXA2XX_MODULE)
 493 static void spitz_ads7846_wait_for_hsync(void)
 494 {
 495         while (gpio_get_value(SPITZ_GPIO_HSYNC))
 496                 cpu_relax();
 497
 498         while (!gpio_get_value(SPITZ_GPIO_HSYNC))
 499                 cpu_relax();
 500 }
 501
 502 static struct ads7846_platform_data spitz_ads7846_info = {
 503         .model                  = 7846,
 504         .vref_delay_usecs       = 100,
 505         .x_plate_ohms           = 419,
 506         .y_plate_ohms           = 486,
 507         .pressure_max           = 1024,
 508         .gpio_pendown           = SPITZ_GPIO_TP_INT,
 509         .wait_for_sync          = spitz_ads7846_wait_for_hsync,
 510 };
 511
 512 static struct pxa2xx_spi_chip spitz_ads7846_chip = {
 513         .gpio_cs                = SPITZ_GPIO_ADS7846_CS,
 514 };
 515
 516 static void spitz_bl_kick_battery(void)
 517 {
 518         void (*kick_batt)(void);
 519
 520         kick_batt = symbol_get(sharpsl_battery_kick);
 521         if (kick_batt) {
 522                 kick_batt();
 523                 symbol_put(sharpsl_battery_kick);
 524         }
 525 }
 526
 527 static struct corgi_lcd_platform_data spitz_lcdcon_info = {
 528         .init_mode              = CORGI_LCD_MODE_VGA,
 529         .max_intensity          = 0x2f,
 530         .default_intensity      = 0x1f,
 531         .limit_mask             = 0x0b,
 532         .gpio_backlight_cont    = SPITZ_GPIO_BACKLIGHT_CONT,
 533         .gpio_backlight_on      = SPITZ_GPIO_BACKLIGHT_ON,
 534         .kick_battery           = spitz_bl_kick_battery,
 535 };
 536
 537 static struct pxa2xx_spi_chip spitz_lcdcon_chip = {
 538         .gpio_cs        = SPITZ_GPIO_LCDCON_CS,
 539 };
 540
 541 static struct pxa2xx_spi_chip spitz_max1111_chip = {
 542         .gpio_cs        = SPITZ_GPIO_MAX1111_CS,
 543 };
 544
 545 static struct spi_board_info spitz_spi_devices[] = {
 546         {
 547                 .modalias               = "ads7846",
 548                 .max_speed_hz           = 1200000,
 549                 .bus_num                = 2,
 550                 .chip_select            = 0,
 551                 .platform_data          = &spitz_ads7846_info,
 552                 .controller_data        = &spitz_ads7846_chip,
 553                 .irq                    = gpio_to_irq(SPITZ_GPIO_TP_INT),
 554         }, {
 555                 .modalias               = "corgi-lcd",
 556                 .max_speed_hz           = 50000,
 557                 .bus_num                = 2,
 558                 .chip_select            = 1,
 559                 .platform_data          = &spitz_lcdcon_info,
 560                 .controller_data        = &spitz_lcdcon_chip,
 561         }, {
 562                 .modalias               = "max1111",
 563                 .max_speed_hz           = 450000,
 564                 .bus_num                = 2,
 565                 .chip_select            = 2,
 566                 .controller_data        = &spitz_max1111_chip,
 567         },
 568 };
 569
 570 static struct pxa2xx_spi_master spitz_spi_info = {
 571         .num_chipselect = 3,
 572 };
 573
 574 static void __init spitz_spi_init(void)
 575 {
 576         struct corgi_lcd_platform_data *lcd_data = &spitz_lcdcon_info;
 577
 578         if (machine_is_akita()) {
 579                 lcd_data->gpio_backlight_cont = AKITA_GPIO_BACKLIGHT_CONT;
 580                 lcd_data->gpio_backlight_on = AKITA_GPIO_BACKLIGHT_ON;
 581         }
 582
 583         pxa2xx_set_spi_info(2, &spitz_spi_info);
 584         spi_register_board_info(ARRAY_AND_SIZE(spitz_spi_devices));
 585 }
 586 #else
 587 static inline void spitz_spi_init(void) {}
 588 #endif
 589
 590 /******************************************************************************
 591  * SD/MMC card controller
 592  ******************************************************************************/
 593 #if defined(CONFIG_MMC_PXA) || defined(CONFIG_MMC_PXA_MODULE)
 594 /*
 595  * NOTE: The card detect interrupt isn't debounced so we delay it by 250ms to
 596  * give the card a chance to fully insert/eject.
 597  */
 598 static void spitz_mci_setpower(struct device *dev, unsigned int vdd)
 599 {
 600         struct pxamci_platform_data* p_d = dev->platform_data;
 601
 602         if ((1 << vdd) & p_d->ocr_mask)
 603                 spitz_card_pwr_ctrl(SCOOP_CPR_SD_3V, SCOOP_CPR_SD_3V);
 604         else
 605                 spitz_card_pwr_ctrl(SCOOP_CPR_SD_3V, 0x0);
 606 }
 607
 608 static struct pxamci_platform_data spitz_mci_platform_data = {
 609         .detect_delay_ms        = 250,
 610         .ocr_mask               = MMC_VDD_32_33|MMC_VDD_33_34,
 611         .setpower               = spitz_mci_setpower,
 612         .gpio_card_detect       = SPITZ_GPIO_nSD_DETECT,
 613         .gpio_card_ro           = SPITZ_GPIO_nSD_WP,
 614         .gpio_power             = -1,
 615 };
 616
 617 static void __init spitz_mmc_init(void)
 618 {
 619         pxa_set_mci_info(&spitz_mci_platform_data);
 620 }
 621 #else
 622 static inline void spitz_mmc_init(void) {}
 623 #endif
 624
 625 /******************************************************************************
 626  * USB Host
 627  ******************************************************************************/
 628 #if defined(CONFIG_USB_OHCI_HCD) || defined(CONFIG_USB_OHCI_HCD_MODULE)
 629 static int spitz_ohci_init(struct device *dev)
 630 {
 631         int err;
 632
 633         err = gpio_request(SPITZ_GPIO_USB_HOST, "USB_HOST");
 634         if (err)
 635                 return err;
 636
 637         /* Only Port 2 is connected, setup USB Port 2 Output Control Register */
 638         UP2OCR = UP2OCR_HXS | UP2OCR_HXOE | UP2OCR_DPPDE | UP2OCR_DMPDE;
 639
 640         return gpio_direction_output(SPITZ_GPIO_USB_HOST, 1);
 641 }
 642
 643 static void spitz_ohci_exit(struct device *dev)
 644 {
 645         gpio_free(SPITZ_GPIO_USB_HOST);
 646 }
 647
 648 static struct pxaohci_platform_data spitz_ohci_platform_data = {
 649         .port_mode      = PMM_NPS_MODE,
 650         .init           = spitz_ohci_init,
 651         .exit           = spitz_ohci_exit,
 652         .flags          = ENABLE_PORT_ALL | NO_OC_PROTECTION,
 653         .power_budget   = 150,
 654 };
 655
 656 static void __init spitz_uhc_init(void)
 657 {
 658         pxa_set_ohci_info(&spitz_ohci_platform_data);
 659 }
 660 #else
 661 static inline void spitz_uhc_init(void) {}
 662 #endif
 663
 664 /******************************************************************************
 665  * IrDA
 666  ******************************************************************************/
 667 #if defined(CONFIG_PXA_FICP) || defined(CONFIG_PXA_FICP_MODULE)
 668 static struct pxaficp_platform_data spitz_ficp_platform_data = {
 669         .transceiver_cap        = IR_SIRMODE | IR_OFF,
 670 };
 671
 672 static void __init spitz_irda_init(void)
 673 {
 674         if (machine_is_akita())
 675                 spitz_ficp_platform_data.gpio_pwdown = AKITA_GPIO_IR_ON;
 676         else
 677                 spitz_ficp_platform_data.gpio_pwdown = SPITZ_GPIO_IR_ON;
 678
 679         pxa_set_ficp_info(&spitz_ficp_platform_data);
 680 }
 681 #else
 682 static inline void spitz_irda_init(void) {}
 683 #endif
 684
 685 /******************************************************************************
 686  * Framebuffer
 687  ******************************************************************************/
 688 #if defined(CONFIG_FB_PXA) || defined(CONFIG_FB_PXA_MODULE)
 689 static struct pxafb_mode_info spitz_pxafb_modes[] = {
 690         {
 691                 .pixclock       = 19231,
 692                 .xres           = 480,
 693                 .yres           = 640,
 694                 .bpp            = 16,
 695                 .hsync_len      = 40,
 696                 .left_margin    = 46,
 697                 .right_margin   = 125,
 698                 .vsync_len      = 3,
 699                 .upper_margin   = 1,
 700                 .lower_margin   = 0,
 701                 .sync           = 0,
 702         }, {
 703                 .pixclock       = 134617,
 704                 .xres           = 240,
 705                 .yres           = 320,
 706                 .bpp            = 16,
 707                 .hsync_len      = 20,
 708                 .left_margin    = 20,
 709                 .right_margin   = 46,
 710                 .vsync_len      = 2,
 711                 .upper_margin   = 1,
 712                 .lower_margin   = 0,
 713                 .sync           = 0,
 714         },
 715 };
 716
 717 static struct pxafb_mach_info spitz_pxafb_info = {
 718         .modes          = spitz_pxafb_modes,
 719         .num_modes      = ARRAY_SIZE(spitz_pxafb_modes),
 720         .fixed_modes    = 1,
 721         .lcd_conn       = LCD_COLOR_TFT_16BPP | LCD_ALTERNATE_MAPPING,
 722 };
 723
 724 static void __init spitz_lcd_init(void)
 725 {
 726         set_pxa_fb_info(&spitz_pxafb_info);
 727 }
 728 #else
 729 static inline void spitz_lcd_init(void) {}
 730 #endif
 731
 732 /******************************************************************************
 733  * Framebuffer
 734  ******************************************************************************/
 735 #if defined(CONFIG_MTD_NAND_SHARPSL) || defined(CONFIG_MTD_NAND_SHARPSL_MODULE)
 736 static struct mtd_partition spitz_nand_partitions[] = {
 737         {
 738                 .name = "System Area",
 739                 .offset = 0,
 740                 .size = 7 * 1024 * 1024,
 741         }, {
 742                 .name = "Root Filesystem",
 743                 .offset = 7 * 1024 * 1024,
 744         }, {
 745                 .name = "Home Filesystem",
 746                 .offset = MTDPART_OFS_APPEND,
 747                 .size = MTDPART_SIZ_FULL,
 748         },
 749 };
 750
 751 static uint8_t scan_ff_pattern[] = { 0xff, 0xff };
 752
 753 static struct nand_bbt_descr spitz_nand_bbt = {
 754         .options        = 0,
 755         .offs           = 4,
 756         .len            = 2,
 757         .pattern        = scan_ff_pattern
 758 };
 759
 760 static struct nand_ecclayout akita_oobinfo = {
 761         .oobfree        = { {0x08, 0x09} },
 762         .eccbytes       = 24,
 763         .eccpos         = {
 764                         0x05, 0x01, 0x02, 0x03, 0x06, 0x07, 0x15, 0x11,
 765                         0x12, 0x13, 0x16, 0x17, 0x25, 0x21, 0x22, 0x23,
 766                         0x26, 0x27, 0x35, 0x31, 0x32, 0x33, 0x36, 0x37,
 767         },
 768 };
 769
 770 static struct sharpsl_nand_platform_data spitz_nand_pdata = {
 771         .badblock_pattern       = &spitz_nand_bbt,
 772         .partitions             = spitz_nand_partitions,
 773         .nr_partitions          = ARRAY_SIZE(spitz_nand_partitions),
 774 };
 775
 776 static struct resource spitz_nand_resources[] = {
 777         {
 778                 .start  = PXA_CS3_PHYS,
 779                 .end    = PXA_CS3_PHYS + SZ_4K - 1,
 780                 .flags  = IORESOURCE_MEM,
 781         },
 782 };
 783
 784 static struct platform_device spitz_nand_device = {
 785         .name           = "sharpsl-nand",
 786         .id             = -1,
 787         .resource       = spitz_nand_resources,
 788         .num_resources  = ARRAY_SIZE(spitz_nand_resources),
 789         .dev            = {
 790                 .platform_data  = &spitz_nand_pdata,
 791         }
 792 };
 793
 794 static void __init spitz_nand_init(void)
 795 {
 796         if (machine_is_spitz()) {
 797                 spitz_nand_partitions[1].size = 5 * 1024 * 1024;
 798         } else if (machine_is_akita()) {
 799                 spitz_nand_partitions[1].size = 58 * 1024 * 1024;
 800                 spitz_nand_bbt.len = 1;
 801                 spitz_nand_pdata.ecc_layout = &akita_oobinfo;
 802         } else if (machine_is_borzoi()) {
 803                 spitz_nand_partitions[1].size = 32 * 1024 * 1024;
 804                 spitz_nand_bbt.len = 1;
 805                 spitz_nand_pdata.ecc_layout = &akita_oobinfo;
 806         }
 807
 808         platform_device_register(&spitz_nand_device);
 809 }
 810 #else
 811 static inline void spitz_nand_init(void) {}
 812 #endif
 813
 814 /******************************************************************************
 815  * NOR Flash
 816  ******************************************************************************/
 817 #if defined(CONFIG_MTD_PHYSMAP) || defined(CONFIG_MTD_PHYSMAP_MODULE)
 818 static struct mtd_partition spitz_rom_parts[] = {
 819         {
 820                 .name   ="Boot PROM Filesystem",
 821                 .offset = 0x00140000,
 822                 .size   = MTDPART_SIZ_FULL,
 823         },
 824 };
 825
 826 static struct physmap_flash_data spitz_rom_data = {
 827         .width          = 2,
 828         .nr_parts       = ARRAY_SIZE(spitz_rom_parts),
 829         .parts          = spitz_rom_parts,
 830 };
 831
 832 static struct resource spitz_rom_resources[] = {
 833         {
 834                 .start  = PXA_CS0_PHYS,
 835                 .end    = PXA_CS0_PHYS + SZ_8M - 1,
 836                 .flags  = IORESOURCE_MEM,
 837         },
 838 };
 839
 840 static struct platform_device spitz_rom_device = {
 841         .name           = "physmap-flash",
 842         .id             = -1,
 843         .resource       = spitz_rom_resources,
 844         .num_resources  = ARRAY_SIZE(spitz_rom_resources),
 845         .dev            = {
 846                 .platform_data  = &spitz_rom_data,
 847         },
 848 };
 849
 850 static void __init spitz_nor_init(void)
 851 {
 852         platform_device_register(&spitz_rom_device);
 853 }
 854 #else
 855 static inline void spitz_nor_init(void) {}
 856 #endif
 857
 858 /******************************************************************************
 859  * GPIO expander
 860  ******************************************************************************/
 861 #if defined(CONFIG_I2C_PXA) || defined(CONFIG_I2C_PXA_MODULE)
 862 static struct pca953x_platform_data akita_pca953x_pdata = {
 863         .gpio_base              = AKITA_IOEXP_GPIO_BASE,
 864 };
 865
 866 static struct i2c_board_info spitz_i2c_devs[] = {
 867         {
 868                 .type           = "wm8750",
 869                 .addr           = 0x1b,
 870         }, {
 871                 .type           = "max7310",
 872                 .addr           = 0x18,
 873                 .platform_data  = &akita_pca953x_pdata,
 874         },
 875 };
 876
 877 static struct regulator_consumer_supply isl6271a_consumers[] = {
 878         {
 879                 .supply = "vcc_core",
 880         }
 881 };
 882
 883 static struct regulator_init_data isl6271a_info[] = {
 884         {
 885                 .constraints = {
 886                         .name           = "vcc_core range",
 887                         .min_uV         = 850000,
 888                         .max_uV         = 1600000,
 889                         .always_on      = 1,
 890                         .valid_ops_mask = REGULATOR_CHANGE_VOLTAGE,
 891                 },
 892         .consumer_supplies      = isl6271a_consumers,
 893         .num_consumer_supplies  = ARRAY_SIZE(isl6271a_consumers),
 894         }
 895 };
 896
 897 static struct i2c_board_info spitz_pi2c_devs[] = {
 898         {
 899                 .type           = "isl6271a",
 900                 .addr           = 0x0c,
 901                 .platform_data  = &isl6271a_info,
 902         },
 903 };
 904
 905 static void __init spitz_i2c_init(void)
 906 {
 907         int size = ARRAY_SIZE(spitz_i2c_devs);
 908
 909         /* Only Akita has the max7310 chip */
 910         if (!machine_is_akita())
 911                 size--;
 912
 913         pxa_set_i2c_info(NULL);
 914         pxa27x_set_i2c_power_info(NULL);
 915         i2c_register_board_info(0, spitz_i2c_devs, size);
 916         i2c_register_board_info(1, ARRAY_AND_SIZE(spitz_pi2c_devs));
 917 }
 918 #else
 919 static inline void spitz_i2c_init(void) {}
 920 #endif
 921
 922 /******************************************************************************
 923  * Machine init
 924  ******************************************************************************/
 925 static void spitz_poweroff(void)
 926 {
 927         arm_machine_restart('g', NULL);
 928 }
 929
 930 static void spitz_restart(char mode, const char *cmd)
 931 {
 932         /* Bootloader magic for a reboot */
 933         if ((MSC0 & 0xffff0000) == 0x7ff00000)
 934                 MSC0 = (MSC0 & 0xffff) | 0x7ee00000;
 935
 936         spitz_poweroff();
 937 }
 938
 939 static void __init spitz_init(void)
 940 {
 941         init_gpio_reset(SPITZ_GPIO_ON_RESET, 1, 0);
 942         pm_power_off = spitz_poweroff;
 943         arm_pm_restart = spitz_restart;
 944
 945         PMCR = 0x00;
 946
 947         /* Stop 3.6MHz and drive HIGH to PCMCIA and CS */
 948         PCFR |= PCFR_OPDE;
 949
 950         pxa2xx_mfp_config(ARRAY_AND_SIZE(spitz_pin_config));
 951
 952         pxa_set_ffuart_info(NULL);
 953         pxa_set_btuart_info(NULL);
 954         pxa_set_stuart_info(NULL);
 955
 956         spitz_spi_init();
 957         spitz_scoop_init();
 958         spitz_mkp_init();
 959         spitz_keys_init();
 960         spitz_leds_init();
 961         spitz_mmc_init();
 962         spitz_pcmcia_init();
 963         spitz_irda_init();
 964         spitz_uhc_init();
 965         spitz_lcd_init();
 966         spitz_nor_init();
 967         spitz_nand_init();
 968         spitz_i2c_init();
 969 }
 970
 971 static void __init spitz_fixup(struct machine_desc *desc,
 972                 struct tag *tags, char **cmdline, struct meminfo *mi)
 973 {
 974         sharpsl_save_param();
 975         mi->nr_banks = 1;
 976         mi->bank[0].start = 0xa0000000;
 977         mi->bank[0].size = (64*1024*1024);
 978 }
 979
 980 #ifdef CONFIG_MACH_SPITZ
 981 MACHINE_START(SPITZ, "SHARP Spitz")
 982         .phys_io        = 0x40000000,
 983         .io_pg_offst    = (io_p2v(0x40000000) >> 18) & 0xfffc,
 984         .fixup          = spitz_fixup,
 985         .map_io         = pxa_map_io,
 986         .init_irq       = pxa27x_init_irq,
 987         .init_machine   = spitz_init,
 988         .timer          = &pxa_timer,
 989 MACHINE_END
 990 #endif
 991
 992 #ifdef CONFIG_MACH_BORZOI
 993 MACHINE_START(BORZOI, "SHARP Borzoi")
 994         .phys_io        = 0x40000000,
 995         .io_pg_offst    = (io_p2v(0x40000000) >> 18) & 0xfffc,
 996         .fixup          = spitz_fixup,
 997         .map_io         = pxa_map_io,
 998         .init_irq       = pxa27x_init_irq,
 999         .init_machine   = spitz_init,
1000         .timer          = &pxa_timer,
1001 MACHINE_END
1002 #endif
1003
1004 #ifdef CONFIG_MACH_AKITA
1005 MACHINE_START(AKITA, "SHARP Akita")
1006         .phys_io        = 0x40000000,
1007         .io_pg_offst    = (io_p2v(0x40000000) >> 18) & 0xfffc,
1008         .fixup          = spitz_fixup,
1009         .map_io         = pxa_map_io,
1010         .init_irq       = pxa27x_init_irq,
1011         .init_machine   = spitz_init,
1012         .timer          = &pxa_timer,
1013 MACHINE_END
1014 #endif