arch/arm/mach-omap2/pm34xx.c

   1 /*
   2  * OMAP3 Power Management Routines
   3  *
   4  * Copyright (C) 2006-2008 Nokia Corporation
   5  * Tony Lindgren <tony@atomide.com>
   6  * Jouni Hogander
   7  *
   8  * Copyright (C) 2007 Texas Instruments, Inc.
   9  * Rajendra Nayak <rnayak@ti.com>
  10  *
  11  * Copyright (C) 2005 Texas Instruments, Inc.
  12  * Richard Woodruff <r-woodruff2@ti.com>
  13  *
  14  * Based on pm.c for omap1
  15  *
  16  * This program is free software; you can redistribute it and/or modify
  17  * it under the terms of the GNU General Public License version 2 as
  18  * published by the Free Software Foundation.
  19  */
  20
  21 #include <linux/pm.h>
  22 #include <linux/suspend.h>
  23 #include <linux/interrupt.h>
  24 #include <linux/module.h>
  25 #include <linux/list.h>
  26 #include <linux/err.h>
  27 #include <linux/gpio.h>
  28 #include <linux/clk.h>
  29 #include <linux/delay.h>
  30 #include <linux/slab.h>
  31
  32 #include <plat/sram.h>
  33 #include <plat/clockdomain.h>
  34 #include <plat/powerdomain.h>
  35 #include <plat/control.h>
  36 #include <plat/serial.h>
  37 #include <plat/sdrc.h>
  38 #include <plat/prcm.h>
  39 #include <plat/gpmc.h>
  40 #include <plat/dma.h>
  41 #include <plat/dmtimer.h>
  42
  43 #include <asm/tlbflush.h>
  44
  45 #include "cm.h"
  46 #include "cm-regbits-34xx.h"
  47 #include "prm-regbits-34xx.h"
  48
  49 #include "prm.h"
  50 #include "pm.h"
  51 #include "sdrc.h"
  52
  53 /* Scratchpad offsets */
  54 #define OMAP343X_TABLE_ADDRESS_OFFSET      0x31
  55 #define OMAP343X_TABLE_VALUE_OFFSET        0x30
  56 #define OMAP343X_CONTROL_REG_VALUE_OFFSET  0x32
  57
  58 u32 enable_off_mode;
  59 u32 sleep_while_idle;
  60 u32 wakeup_timer_seconds;
  61 u32 wakeup_timer_milliseconds;
  62
  63 struct power_state {
  64         struct powerdomain *pwrdm;
  65         u32 next_state;
  66 #ifdef CONFIG_SUSPEND
  67         u32 saved_state;
  68 #endif
  69         struct list_head node;
  70 };
  71
  72 static LIST_HEAD(pwrst_list);
  73
  74 static void (*_omap_sram_idle)(u32 *addr, int save_state);
  75
  76 static int (*_omap_save_secure_sram)(u32 *addr);
  77
  78 static struct powerdomain *mpu_pwrdm, *neon_pwrdm;
  79 static struct powerdomain *core_pwrdm, *per_pwrdm;
  80 static struct powerdomain *cam_pwrdm;
  81
  82 static inline void omap3_per_save_context(void)
  83 {
  84         omap_gpio_save_context();
  85 }
  86
  87 static inline void omap3_per_restore_context(void)
  88 {
  89         omap_gpio_restore_context();
  90 }
  91
  92 static void omap3_enable_io_chain(void)
  93 {
  94         int timeout = 0;
  95
  96         if (omap_rev() >= OMAP3430_REV_ES3_1) {
  97                 prm_set_mod_reg_bits(OMAP3430_EN_IO_CHAIN_MASK, WKUP_MOD,
  98                                      PM_WKEN);
  99                 /* Do a readback to assure write has been done */
 100                 prm_read_mod_reg(WKUP_MOD, PM_WKEN);
 101
 102                 while (!(prm_read_mod_reg(WKUP_MOD, PM_WKEN) &
 103                          OMAP3430_ST_IO_CHAIN_MASK)) {
 104                         timeout++;
 105                         if (timeout > 1000) {
 106                                 printk(KERN_ERR "Wake up daisy chain "
 107                                        "activation failed.\n");
 108                                 return;
 109                         }
 110                         prm_set_mod_reg_bits(OMAP3430_ST_IO_CHAIN_MASK,
 111                                              WKUP_MOD, PM_WKEN);
 112                 }
 113         }
 114 }
 115
 116 static void omap3_disable_io_chain(void)
 117 {
 118         if (omap_rev() >= OMAP3430_REV_ES3_1)
 119                 prm_clear_mod_reg_bits(OMAP3430_EN_IO_CHAIN_MASK, WKUP_MOD,
 120                                        PM_WKEN);
 121 }
 122
 123 static void omap3_core_save_context(void)
 124 {
 125         u32 control_padconf_off;
 126
 127         /* Save the padconf registers */
 128         control_padconf_off = omap_ctrl_readl(OMAP343X_CONTROL_PADCONF_OFF);
 129         control_padconf_off |= START_PADCONF_SAVE;
 130         omap_ctrl_writel(control_padconf_off, OMAP343X_CONTROL_PADCONF_OFF);
 131         /* wait for the save to complete */
 132         while (!(omap_ctrl_readl(OMAP343X_CONTROL_GENERAL_PURPOSE_STATUS)
 133                         & PADCONF_SAVE_DONE))
 134                 udelay(1);
 135
 136         /*
 137          * Force write last pad into memory, as this can fail in some
 138          * cases according to erratas 1.157, 1.185
 139          */
 140         omap_ctrl_writel(omap_ctrl_readl(OMAP343X_PADCONF_ETK_D14),
 141                 OMAP343X_CONTROL_MEM_WKUP + 0x2a0);
 142
 143         /* Save the Interrupt controller context */
 144         omap_intc_save_context();
 145         /* Save the GPMC context */
 146         omap3_gpmc_save_context();
 147         /* Save the system control module context, padconf already save above*/
 148         omap3_control_save_context();
 149         omap_dma_global_context_save();
 150 }
 151
 152 static void omap3_core_restore_context(void)
 153 {
 154         /* Restore the control module context, padconf restored by h/w */
 155         omap3_control_restore_context();
 156         /* Restore the GPMC context */
 157         omap3_gpmc_restore_context();
 158         /* Restore the interrupt controller context */
 159         omap_intc_restore_context();
 160         omap_dma_global_context_restore();
 161 }
 162
 163 /*
 164  * FIXME: This function should be called before entering off-mode after
 165  * OMAP3 secure services have been accessed. Currently it is only called
 166  * once during boot sequence, but this works as we are not using secure
 167  * services.
 168  */
 169 static void omap3_save_secure_ram_context(u32 target_mpu_state)
 170 {
 171         u32 ret;
 172
 173         if (omap_type() != OMAP2_DEVICE_TYPE_GP) {
 174                 /*
 175                  * MPU next state must be set to POWER_ON temporarily,
 176                  * otherwise the WFI executed inside the ROM code
 177                  * will hang the system.
 178                  */
 179                 pwrdm_set_next_pwrst(mpu_pwrdm, PWRDM_POWER_ON);
 180                 ret = _omap_save_secure_sram((u32 *)
 181                                 __pa(omap3_secure_ram_storage));
 182                 pwrdm_set_next_pwrst(mpu_pwrdm, target_mpu_state);
 183                 /* Following is for error tracking, it should not happen */
 184                 if (ret) {
 185                         printk(KERN_ERR "save_secure_sram() returns %08x\n",
 186                                 ret);
 187                         while (1)
 188                                 ;
 189                 }
 190         }
 191 }
 192
 193 /*
 194  * PRCM Interrupt Handler Helper Function
 195  *
 196  * The purpose of this function is to clear any wake-up events latched
 197  * in the PRCM PM_WKST_x registers. It is possible that a wake-up event
 198  * may occur whilst attempting to clear a PM_WKST_x register and thus
 199  * set another bit in this register. A while loop is used to ensure
 200  * that any peripheral wake-up events occurring while attempting to
 201  * clear the PM_WKST_x are detected and cleared.
 202  */
 203 static int prcm_clear_mod_irqs(s16 module, u8 regs)
 204 {
 205         u32 wkst, fclk, iclk, clken;
 206         u16 wkst_off = (regs == 3) ? OMAP3430ES2_PM_WKST3 : PM_WKST1;
 207         u16 fclk_off = (regs == 3) ? OMAP3430ES2_CM_FCLKEN3 : CM_FCLKEN1;
 208         u16 iclk_off = (regs == 3) ? CM_ICLKEN3 : CM_ICLKEN1;
 209         u16 grpsel_off = (regs == 3) ?
 210                 OMAP3430ES2_PM_MPUGRPSEL3 : OMAP3430_PM_MPUGRPSEL;
 211         int c = 0;
 212
 213         wkst = prm_read_mod_reg(module, wkst_off);
 214         wkst &= prm_read_mod_reg(module, grpsel_off);
 215         if (wkst) {
 216                 iclk = cm_read_mod_reg(module, iclk_off);
 217                 fclk = cm_read_mod_reg(module, fclk_off);
 218                 while (wkst) {
 219                         clken = wkst;
 220                         cm_set_mod_reg_bits(clken, module, iclk_off);
 221                         /*
 222                          * For USBHOST, we don't know whether HOST1 or
 223                          * HOST2 woke us up, so enable both f-clocks
 224                          */
 225                         if (module == OMAP3430ES2_USBHOST_MOD)
 226                                 clken |= 1 << OMAP3430ES2_EN_USBHOST2_SHIFT;
 227                         cm_set_mod_reg_bits(clken, module, fclk_off);
 228                         prm_write_mod_reg(wkst, module, wkst_off);
 229                         wkst = prm_read_mod_reg(module, wkst_off);
 230                         c++;
 231                 }
 232                 cm_write_mod_reg(iclk, module, iclk_off);
 233                 cm_write_mod_reg(fclk, module, fclk_off);
 234         }
 235
 236         return c;
 237 }
 238
 239 static int _prcm_int_handle_wakeup(void)
 240 {
 241         int c;
 242
 243         c = prcm_clear_mod_irqs(WKUP_MOD, 1);
 244         c += prcm_clear_mod_irqs(CORE_MOD, 1);
 245         c += prcm_clear_mod_irqs(OMAP3430_PER_MOD, 1);
 246         if (omap_rev() > OMAP3430_REV_ES1_0) {
 247                 c += prcm_clear_mod_irqs(CORE_MOD, 3);
 248                 c += prcm_clear_mod_irqs(OMAP3430ES2_USBHOST_MOD, 1);
 249         }
 250
 251         return c;
 252 }
 253
 254 /*
 255  * PRCM Interrupt Handler
 256  *
 257  * The PRM_IRQSTATUS_MPU register indicates if there are any pending
 258  * interrupts from the PRCM for the MPU. These bits must be cleared in
 259  * order to clear the PRCM interrupt. The PRCM interrupt handler is
 260  * implemented to simply clear the PRM_IRQSTATUS_MPU in order to clear
 261  * the PRCM interrupt. Please note that bit 0 of the PRM_IRQSTATUS_MPU
 262  * register indicates that a wake-up event is pending for the MPU and
 263  * this bit can only be cleared if the all the wake-up events latched
 264  * in the various PM_WKST_x registers have been cleared. The interrupt
 265  * handler is implemented using a do-while loop so that if a wake-up
 266  * event occurred during the processing of the prcm interrupt handler
 267  * (setting a bit in the corresponding PM_WKST_x register and thus
 268  * preventing us from clearing bit 0 of the PRM_IRQSTATUS_MPU register)
 269  * this would be handled.
 270  */
 271 static irqreturn_t prcm_interrupt_handler (int irq, void *dev_id)
 272 {
 273         u32 irqenable_mpu, irqstatus_mpu;
 274         int c = 0;
 275
 276         irqenable_mpu = prm_read_mod_reg(OCP_MOD,
 277                                          OMAP3_PRM_IRQENABLE_MPU_OFFSET);
 278         irqstatus_mpu = prm_read_mod_reg(OCP_MOD,
 279                                          OMAP3_PRM_IRQSTATUS_MPU_OFFSET);
 280         irqstatus_mpu &= irqenable_mpu;
 281
 282         do {
 283                 if (irqstatus_mpu & (OMAP3430_WKUP_ST_MASK |
 284                                      OMAP3430_IO_ST_MASK)) {
 285                         c = _prcm_int_handle_wakeup();
 286
 287                         /*
 288                          * Is the MPU PRCM interrupt handler racing with the
 289                          * IVA2 PRCM interrupt handler ?
 290                          */
 291                         WARN(c == 0, "prcm: WARNING: PRCM indicated MPU wakeup "
 292                              "but no wakeup sources are marked\n");
 293                 } else {
 294                         /* XXX we need to expand our PRCM interrupt handler */
 295                         WARN(1, "prcm: WARNING: PRCM interrupt received, but "
 296                              "no code to handle it (%08x)\n", irqstatus_mpu);
 297                 }
 298
 299                 prm_write_mod_reg(irqstatus_mpu, OCP_MOD,
 300                                         OMAP3_PRM_IRQSTATUS_MPU_OFFSET);
 301
 302                 irqstatus_mpu = prm_read_mod_reg(OCP_MOD,
 303                                         OMAP3_PRM_IRQSTATUS_MPU_OFFSET);
 304                 irqstatus_mpu &= irqenable_mpu;
 305
 306         } while (irqstatus_mpu);
 307
 308         return IRQ_HANDLED;
 309 }
 310
 311 static void restore_control_register(u32 val)
 312 {
 313         __asm__ __volatile__ ("mcr p15, 0, %0, c1, c0, 0" : : "r" (val));
 314 }
 315
 316 /* Function to restore the table entry that was modified for enabling MMU */
 317 static void restore_table_entry(void)
 318 {
 319         u32 *scratchpad_address;
 320         u32 previous_value, control_reg_value;
 321         u32 *address;
 322
 323         scratchpad_address = OMAP2_L4_IO_ADDRESS(OMAP343X_SCRATCHPAD);
 324
 325         /* Get address of entry that was modified */
 326         address = (u32 *)__raw_readl(scratchpad_address +
 327                                      OMAP343X_TABLE_ADDRESS_OFFSET);
 328         /* Get the previous value which needs to be restored */
 329         previous_value = __raw_readl(scratchpad_address +
 330                                      OMAP343X_TABLE_VALUE_OFFSET);
 331         address = __va(address);
 332         *address = previous_value;
 333         flush_tlb_all();
 334         control_reg_value = __raw_readl(scratchpad_address
 335                                         + OMAP343X_CONTROL_REG_VALUE_OFFSET);
 336         /* This will enable caches and prediction */
 337         restore_control_register(control_reg_value);
 338 }
 339
 340 void omap_sram_idle(void)
 341 {
 342         /* Variable to tell what needs to be saved and restored
 343          * in omap_sram_idle*/
 344         /* save_state = 0 => Nothing to save and restored */
 345         /* save_state = 1 => Only L1 and logic lost */
 346         /* save_state = 2 => Only L2 lost */
 347         /* save_state = 3 => L1, L2 and logic lost */
 348         int save_state = 0;
 349         int mpu_next_state = PWRDM_POWER_ON;
 350         int per_next_state = PWRDM_POWER_ON;
 351         int core_next_state = PWRDM_POWER_ON;
 352         int core_prev_state, per_prev_state;
 353         u32 sdrc_pwr = 0;
 354         int per_state_modified = 0;
 355
 356         if (!_omap_sram_idle)
 357                 return;
 358
 359         pwrdm_clear_all_prev_pwrst(mpu_pwrdm);
 360         pwrdm_clear_all_prev_pwrst(neon_pwrdm);
 361         pwrdm_clear_all_prev_pwrst(core_pwrdm);
 362         pwrdm_clear_all_prev_pwrst(per_pwrdm);
 363
 364         mpu_next_state = pwrdm_read_next_pwrst(mpu_pwrdm);
 365         switch (mpu_next_state) {
 366         case PWRDM_POWER_ON:
 367         case PWRDM_POWER_RET:
 368                 /* No need to save context */
 369                 save_state = 0;
 370                 break;
 371         case PWRDM_POWER_OFF:
 372                 save_state = 3;
 373                 break;
 374         default:
 375                 /* Invalid state */
 376                 printk(KERN_ERR "Invalid mpu state in sram_idle\n");
 377                 return;
 378         }
 379         pwrdm_pre_transition();
 380
 381         /* NEON control */
 382         if (pwrdm_read_pwrst(neon_pwrdm) == PWRDM_POWER_ON)
 383                 pwrdm_set_next_pwrst(neon_pwrdm, mpu_next_state);
 384
 385         /* Enable IO-PAD and IO-CHAIN wakeups */
 386         per_next_state = pwrdm_read_next_pwrst(per_pwrdm);
 387         core_next_state = pwrdm_read_next_pwrst(core_pwrdm);
 388         if (omap3_has_io_wakeup() && \
 389                         (per_next_state < PWRDM_POWER_ON ||
 390                         core_next_state < PWRDM_POWER_ON)) {
 391                 prm_set_mod_reg_bits(OMAP3430_EN_IO_MASK, WKUP_MOD, PM_WKEN);
 392                 omap3_enable_io_chain();
 393         }
 394
 395         /* PER */
 396         if (per_next_state < PWRDM_POWER_ON) {
 397                 omap_uart_prepare_idle(2);
 398                 omap2_gpio_prepare_for_idle(per_next_state);
 399                 if (per_next_state == PWRDM_POWER_OFF) {
 400                         if (core_next_state == PWRDM_POWER_ON) {
 401                                 per_next_state = PWRDM_POWER_RET;
 402                                 pwrdm_set_next_pwrst(per_pwrdm, per_next_state);
 403                                 per_state_modified = 1;
 404                         } else
 405                                 omap3_per_save_context();
 406                 }
 407         }
 408
 409         if (pwrdm_read_pwrst(cam_pwrdm) == PWRDM_POWER_ON)
 410                 omap2_clkdm_deny_idle(mpu_pwrdm->pwrdm_clkdms[0]);
 411
 412         /* CORE */
 413         if (core_next_state < PWRDM_POWER_ON) {
 414                 omap_uart_prepare_idle(0);
 415                 omap_uart_prepare_idle(1);
 416                 if (core_next_state == PWRDM_POWER_OFF) {
 417                         omap3_core_save_context();
 418                         omap3_prcm_save_context();
 419                 }
 420         }
 421
 422         omap3_intc_prepare_idle();
 423
 424         /*
 425         * On EMU/HS devices ROM code restores a SRDC value
 426         * from scratchpad which has automatic self refresh on timeout
 427         * of AUTO_CNT = 1 enabled. This takes care of errata 1.142.
 428         * Hence store/restore the SDRC_POWER register here.
 429         */
 430         if (omap_rev() >= OMAP3430_REV_ES3_0 &&
 431             omap_type() != OMAP2_DEVICE_TYPE_GP &&
 432             core_next_state == PWRDM_POWER_OFF)
 433                 sdrc_pwr = sdrc_read_reg(SDRC_POWER);
 434
 435         /*
 436          * omap3_arm_context is the location where ARM registers
 437          * get saved. The restore path then reads from this
 438          * location and restores them back.
 439          */
 440         _omap_sram_idle(omap3_arm_context, save_state);
 441         cpu_init();
 442
 443         /* Restore normal SDRC POWER settings */
 444         if (omap_rev() >= OMAP3430_REV_ES3_0 &&
 445             omap_type() != OMAP2_DEVICE_TYPE_GP &&
 446             core_next_state == PWRDM_POWER_OFF)
 447                 sdrc_write_reg(sdrc_pwr, SDRC_POWER);
 448
 449         /* Restore table entry modified during MMU restoration */
 450         if (pwrdm_read_prev_pwrst(mpu_pwrdm) == PWRDM_POWER_OFF)
 451                 restore_table_entry();
 452
 453         /* CORE */
 454         if (core_next_state < PWRDM_POWER_ON) {
 455                 core_prev_state = pwrdm_read_prev_pwrst(core_pwrdm);
 456                 if (core_prev_state == PWRDM_POWER_OFF) {
 457                         omap3_core_restore_context();
 458                         omap3_prcm_restore_context();
 459                         omap3_sram_restore_context();
 460                         omap2_sms_restore_context();
 461                 }
 462                 omap_uart_resume_idle(0);
 463                 omap_uart_resume_idle(1);
 464                 if (core_next_state == PWRDM_POWER_OFF)
 465                         prm_clear_mod_reg_bits(OMAP3430_AUTO_OFF_MASK,
 466                                                OMAP3430_GR_MOD,
 467                                                OMAP3_PRM_VOLTCTRL_OFFSET);
 468         }
 469         omap3_intc_resume_idle();
 470
 471         /* PER */
 472         if (per_next_state < PWRDM_POWER_ON) {
 473                 per_prev_state = pwrdm_read_prev_pwrst(per_pwrdm);
 474                 omap2_gpio_resume_after_idle();
 475                 if (per_prev_state == PWRDM_POWER_OFF)
 476                         omap3_per_restore_context();
 477                 omap_uart_resume_idle(2);
 478                 if (per_state_modified)
 479                         pwrdm_set_next_pwrst(per_pwrdm, PWRDM_POWER_OFF);
 480         }
 481
 482         /* Disable IO-PAD and IO-CHAIN wakeup */
 483         if (omap3_has_io_wakeup() && core_next_state < PWRDM_POWER_ON) {
 484                 prm_clear_mod_reg_bits(OMAP3430_EN_IO_MASK, WKUP_MOD, PM_WKEN);
 485                 omap3_disable_io_chain();
 486         }
 487
 488         pwrdm_post_transition();
 489
 490         omap2_clkdm_allow_idle(mpu_pwrdm->pwrdm_clkdms[0]);
 491 }
 492
 493 int omap3_can_sleep(void)
 494 {
 495         if (!sleep_while_idle)
 496                 return 0;
 497         if (!omap_uart_can_sleep())
 498                 return 0;
 499         return 1;
 500 }
 501
 502 /* This sets pwrdm state (other than mpu & core. Currently only ON &
 503  * RET are supported. Function is assuming that clkdm doesn't have
 504  * hw_sup mode enabled. */
 505 int set_pwrdm_state(struct powerdomain *pwrdm, u32 state)
 506 {
 507         u32 cur_state;
 508         int sleep_switch = 0;
 509         int ret = 0;
 510
 511         if (pwrdm == NULL || IS_ERR(pwrdm))
 512                 return -EINVAL;
 513
 514         while (!(pwrdm->pwrsts & (1 << state))) {
 515                 if (state == PWRDM_POWER_OFF)
 516                         return ret;
 517                 state--;
 518         }
 519
 520         cur_state = pwrdm_read_next_pwrst(pwrdm);
 521         if (cur_state == state)
 522                 return ret;
 523
 524         if (pwrdm_read_pwrst(pwrdm) < PWRDM_POWER_ON) {
 525                 omap2_clkdm_wakeup(pwrdm->pwrdm_clkdms[0]);
 526                 sleep_switch = 1;
 527                 pwrdm_wait_transition(pwrdm);
 528         }
 529
 530         ret = pwrdm_set_next_pwrst(pwrdm, state);
 531         if (ret) {
 532                 printk(KERN_ERR "Unable to set state of powerdomain: %s\n",
 533                        pwrdm->name);
 534                 goto err;
 535         }
 536
 537         if (sleep_switch) {
 538                 omap2_clkdm_allow_idle(pwrdm->pwrdm_clkdms[0]);
 539                 pwrdm_wait_transition(pwrdm);
 540                 pwrdm_state_switch(pwrdm);
 541         }
 542
 543 err:
 544         return ret;
 545 }
 546
 547 static void omap3_pm_idle(void)
 548 {
 549         local_irq_disable();
 550         local_fiq_disable();
 551
 552         if (!omap3_can_sleep())
 553                 goto out;
 554
 555         if (omap_irq_pending() || need_resched())
 556                 goto out;
 557
 558         omap_sram_idle();
 559
 560 out:
 561         local_fiq_enable();
 562         local_irq_enable();
 563 }
 564
 565 #ifdef CONFIG_SUSPEND
 566 static suspend_state_t suspend_state;
 567
 568 static void omap2_pm_wakeup_on_timer(u32 seconds, u32 milliseconds)
 569 {
 570         u32 tick_rate, cycles;
 571
 572         if (!seconds && !milliseconds)
 573                 return;
 574
 575         tick_rate = clk_get_rate(omap_dm_timer_get_fclk(gptimer_wakeup));
 576         cycles = tick_rate * seconds + tick_rate * milliseconds / 1000;
 577         omap_dm_timer_stop(gptimer_wakeup);
 578         omap_dm_timer_set_load_start(gptimer_wakeup, 0, 0xffffffff - cycles);
 579
 580         pr_info("PM: Resume timer in %u.%03u secs"
 581                 " (%d ticks at %d ticks/sec.)\n",
 582                 seconds, milliseconds, cycles, tick_rate);
 583 }
 584
 585 static int omap3_pm_prepare(void)
 586 {
 587         disable_hlt();
 588         return 0;
 589 }
 590
 591 static int omap3_pm_suspend(void)
 592 {
 593         struct power_state *pwrst;
 594         int state, ret = 0;
 595
 596         if (wakeup_timer_seconds || wakeup_timer_milliseconds)
 597                 omap2_pm_wakeup_on_timer(wakeup_timer_seconds,
 598                                          wakeup_timer_milliseconds);
 599
 600         /* Read current next_pwrsts */
 601         list_for_each_entry(pwrst, &pwrst_list, node)
 602                 pwrst->saved_state = pwrdm_read_next_pwrst(pwrst->pwrdm);
 603         /* Set ones wanted by suspend */
 604         list_for_each_entry(pwrst, &pwrst_list, node) {
 605                 if (set_pwrdm_state(pwrst->pwrdm, pwrst->next_state))
 606                         goto restore;
 607                 if (pwrdm_clear_all_prev_pwrst(pwrst->pwrdm))
 608                         goto restore;
 609         }
 610
 611         omap_uart_prepare_suspend();
 612         omap3_intc_suspend();
 613
 614         omap_sram_idle();
 615
 616 restore:
 617         /* Restore next_pwrsts */
 618         list_for_each_entry(pwrst, &pwrst_list, node) {
 619                 state = pwrdm_read_prev_pwrst(pwrst->pwrdm);
 620                 if (state > pwrst->next_state) {
 621                         printk(KERN_INFO "Powerdomain (%s) didn't enter "
 622                                "target state %d\n",
 623                                pwrst->pwrdm->name, pwrst->next_state);
 624                         ret = -1;
 625                 }
 626                 set_pwrdm_state(pwrst->pwrdm, pwrst->saved_state);
 627         }
 628         if (ret)
 629                 printk(KERN_ERR "Could not enter target state in pm_suspend\n");
 630         else
 631                 printk(KERN_INFO "Successfully put all powerdomains "
 632                        "to target state\n");
 633
 634         return ret;
 635 }
 636
 637 static int omap3_pm_enter(suspend_state_t unused)
 638 {
 639         int ret = 0;
 640
 641         switch (suspend_state) {
 642         case PM_SUSPEND_STANDBY:
 643         case PM_SUSPEND_MEM:
 644                 ret = omap3_pm_suspend();
 645                 break;
 646         default:
 647                 ret = -EINVAL;
 648         }
 649
 650         return ret;
 651 }
 652
 653 static void omap3_pm_finish(void)
 654 {
 655         enable_hlt();
 656 }
 657
 658 /* Hooks to enable / disable UART interrupts during suspend */
 659 static int omap3_pm_begin(suspend_state_t state)
 660 {
 661         suspend_state = state;
 662         omap_uart_enable_irqs(0);
 663         return 0;
 664 }
 665
 666 static void omap3_pm_end(void)
 667 {
 668         suspend_state = PM_SUSPEND_ON;
 669         omap_uart_enable_irqs(1);
 670         return;
 671 }
 672
 673 static struct platform_suspend_ops omap_pm_ops = {
 674         .begin          = omap3_pm_begin,
 675         .end            = omap3_pm_end,
 676         .prepare        = omap3_pm_prepare,
 677         .enter          = omap3_pm_enter,
 678         .finish         = omap3_pm_finish,
 679         .valid          = suspend_valid_only_mem,
 680 };
 681 #endif /* CONFIG_SUSPEND */
 682
 683
 684 /**
 685  * omap3_iva_idle(): ensure IVA is in idle so it can be put into
 686  *                   retention
 687  *
 688  * In cases where IVA2 is activated by bootcode, it may prevent
 689  * full-chip retention or off-mode because it is not idle.  This
 690  * function forces the IVA2 into idle state so it can go
 691  * into retention/off and thus allow full-chip retention/off.
 692  *
 693  **/
 694 static void __init omap3_iva_idle(void)
 695 {
 696         /* ensure IVA2 clock is disabled */
 697         cm_write_mod_reg(0, OMAP3430_IVA2_MOD, CM_FCLKEN);
 698
 699         /* if no clock activity, nothing else to do */
 700         if (!(cm_read_mod_reg(OMAP3430_IVA2_MOD, OMAP3430_CM_CLKSTST) &
 701               OMAP3430_CLKACTIVITY_IVA2_MASK))
 702                 return;
 703
 704         /* Reset IVA2 */
 705         prm_write_mod_reg(OMAP3430_RST1_IVA2_MASK |
 706                           OMAP3430_RST2_IVA2_MASK |
 707                           OMAP3430_RST3_IVA2_MASK,
 708                           OMAP3430_IVA2_MOD, OMAP2_RM_RSTCTRL);
 709
 710         /* Enable IVA2 clock */
 711         cm_write_mod_reg(OMAP3430_CM_FCLKEN_IVA2_EN_IVA2_MASK,
 712                          OMAP3430_IVA2_MOD, CM_FCLKEN);
 713
 714         /* Set IVA2 boot mode to 'idle' */
 715         omap_ctrl_writel(OMAP3_IVA2_BOOTMOD_IDLE,
 716                          OMAP343X_CONTROL_IVA2_BOOTMOD);
 717
 718         /* Un-reset IVA2 */
 719         prm_write_mod_reg(0, OMAP3430_IVA2_MOD, OMAP2_RM_RSTCTRL);
 720
 721         /* Disable IVA2 clock */
 722         cm_write_mod_reg(0, OMAP3430_IVA2_MOD, CM_FCLKEN);
 723
 724         /* Reset IVA2 */
 725         prm_write_mod_reg(OMAP3430_RST1_IVA2_MASK |
 726                           OMAP3430_RST2_IVA2_MASK |
 727                           OMAP3430_RST3_IVA2_MASK,
 728                           OMAP3430_IVA2_MOD, OMAP2_RM_RSTCTRL);
 729 }
 730
 731 static void __init omap3_d2d_idle(void)
 732 {
 733         u16 mask, padconf;
 734
 735         /* In a stand alone OMAP3430 where there is not a stacked
 736          * modem for the D2D Idle Ack and D2D MStandby must be pulled
 737          * high. S CONTROL_PADCONF_SAD2D_IDLEACK and
 738          * CONTROL_PADCONF_SAD2D_MSTDBY to have a pull up. */
 739         mask = (1 << 4) | (1 << 3); /* pull-up, enabled */
 740         padconf = omap_ctrl_readw(OMAP3_PADCONF_SAD2D_MSTANDBY);
 741         padconf |= mask;
 742         omap_ctrl_writew(padconf, OMAP3_PADCONF_SAD2D_MSTANDBY);
 743
 744         padconf = omap_ctrl_readw(OMAP3_PADCONF_SAD2D_IDLEACK);
 745         padconf |= mask;
 746         omap_ctrl_writew(padconf, OMAP3_PADCONF_SAD2D_IDLEACK);
 747
 748         /* reset modem */
 749         prm_write_mod_reg(OMAP3430_RM_RSTCTRL_CORE_MODEM_SW_RSTPWRON_MASK |
 750                           OMAP3430_RM_RSTCTRL_CORE_MODEM_SW_RST_MASK,
 751                           CORE_MOD, OMAP2_RM_RSTCTRL);
 752         prm_write_mod_reg(0, CORE_MOD, OMAP2_RM_RSTCTRL);
 753 }
 754
 755 static void __init prcm_setup_regs(void)
 756 {
 757         /* XXX Reset all wkdeps. This should be done when initializing
 758          * powerdomains */
 759         prm_write_mod_reg(0, OMAP3430_IVA2_MOD, PM_WKDEP);
 760         prm_write_mod_reg(0, MPU_MOD, PM_WKDEP);
 761         prm_write_mod_reg(0, OMAP3430_DSS_MOD, PM_WKDEP);
 762         prm_write_mod_reg(0, OMAP3430_NEON_MOD, PM_WKDEP);
 763         prm_write_mod_reg(0, OMAP3430_CAM_MOD, PM_WKDEP);
 764         prm_write_mod_reg(0, OMAP3430_PER_MOD, PM_WKDEP);
 765         if (omap_rev() > OMAP3430_REV_ES1_0) {
 766                 prm_write_mod_reg(0, OMAP3430ES2_SGX_MOD, PM_WKDEP);
 767                 prm_write_mod_reg(0, OMAP3430ES2_USBHOST_MOD, PM_WKDEP);
 768         } else
 769                 prm_write_mod_reg(0, GFX_MOD, PM_WKDEP);
 770
 771         /*
 772          * Enable interface clock autoidle for all modules.
 773          * Note that in the long run this should be done by clockfw
 774          */
 775         cm_write_mod_reg(
 776                 OMAP3430_AUTO_MODEM_MASK |
 777                 OMAP3430ES2_AUTO_MMC3_MASK |
 778                 OMAP3430ES2_AUTO_ICR_MASK |
 779                 OMAP3430_AUTO_AES2_MASK |
 780                 OMAP3430_AUTO_SHA12_MASK |
 781                 OMAP3430_AUTO_DES2_MASK |
 782                 OMAP3430_AUTO_MMC2_MASK |
 783                 OMAP3430_AUTO_MMC1_MASK |
 784                 OMAP3430_AUTO_MSPRO_MASK |
 785                 OMAP3430_AUTO_HDQ_MASK |
 786                 OMAP3430_AUTO_MCSPI4_MASK |
 787                 OMAP3430_AUTO_MCSPI3_MASK |
 788                 OMAP3430_AUTO_MCSPI2_MASK |
 789                 OMAP3430_AUTO_MCSPI1_MASK |
 790                 OMAP3430_AUTO_I2C3_MASK |
 791                 OMAP3430_AUTO_I2C2_MASK |
 792                 OMAP3430_AUTO_I2C1_MASK |
 793                 OMAP3430_AUTO_UART2_MASK |
 794                 OMAP3430_AUTO_UART1_MASK |
 795                 OMAP3430_AUTO_GPT11_MASK |
 796                 OMAP3430_AUTO_GPT10_MASK |
 797                 OMAP3430_AUTO_MCBSP5_MASK |
 798                 OMAP3430_AUTO_MCBSP1_MASK |
 799                 OMAP3430ES1_AUTO_FAC_MASK | /* This is es1 only */
 800                 OMAP3430_AUTO_MAILBOXES_MASK |
 801                 OMAP3430_AUTO_OMAPCTRL_MASK |
 802                 OMAP3430ES1_AUTO_FSHOSTUSB_MASK |
 803                 OMAP3430_AUTO_HSOTGUSB_MASK |
 804                 OMAP3430_AUTO_SAD2D_MASK |
 805                 OMAP3430_AUTO_SSI_MASK,
 806                 CORE_MOD, CM_AUTOIDLE1);
 807
 808         cm_write_mod_reg(
 809                 OMAP3430_AUTO_PKA_MASK |
 810                 OMAP3430_AUTO_AES1_MASK |
 811                 OMAP3430_AUTO_RNG_MASK |
 812                 OMAP3430_AUTO_SHA11_MASK |
 813                 OMAP3430_AUTO_DES1_MASK,
 814                 CORE_MOD, CM_AUTOIDLE2);
 815
 816         if (omap_rev() > OMAP3430_REV_ES1_0) {
 817                 cm_write_mod_reg(
 818                         OMAP3430_AUTO_MAD2D_MASK |
 819                         OMAP3430ES2_AUTO_USBTLL_MASK,
 820                         CORE_MOD, CM_AUTOIDLE3);
 821         }
 822
 823         cm_write_mod_reg(
 824                 OMAP3430_AUTO_WDT2_MASK |
 825                 OMAP3430_AUTO_WDT1_MASK |
 826                 OMAP3430_AUTO_GPIO1_MASK |
 827                 OMAP3430_AUTO_32KSYNC_MASK |
 828                 OMAP3430_AUTO_GPT12_MASK |
 829                 OMAP3430_AUTO_GPT1_MASK,
 830                 WKUP_MOD, CM_AUTOIDLE);
 831
 832         cm_write_mod_reg(
 833                 OMAP3430_AUTO_DSS_MASK,
 834                 OMAP3430_DSS_MOD,
 835                 CM_AUTOIDLE);
 836
 837         cm_write_mod_reg(
 838                 OMAP3430_AUTO_CAM_MASK,
 839                 OMAP3430_CAM_MOD,
 840                 CM_AUTOIDLE);
 841
 842         cm_write_mod_reg(
 843                 OMAP3430_AUTO_GPIO6_MASK |
 844                 OMAP3430_AUTO_GPIO5_MASK |
 845                 OMAP3430_AUTO_GPIO4_MASK |
 846                 OMAP3430_AUTO_GPIO3_MASK |
 847                 OMAP3430_AUTO_GPIO2_MASK |
 848                 OMAP3430_AUTO_WDT3_MASK |
 849                 OMAP3430_AUTO_UART3_MASK |
 850                 OMAP3430_AUTO_GPT9_MASK |
 851                 OMAP3430_AUTO_GPT8_MASK |
 852                 OMAP3430_AUTO_GPT7_MASK |
 853                 OMAP3430_AUTO_GPT6_MASK |
 854                 OMAP3430_AUTO_GPT5_MASK |
 855                 OMAP3430_AUTO_GPT4_MASK |
 856                 OMAP3430_AUTO_GPT3_MASK |
 857                 OMAP3430_AUTO_GPT2_MASK |
 858                 OMAP3430_AUTO_MCBSP4_MASK |
 859                 OMAP3430_AUTO_MCBSP3_MASK |
 860                 OMAP3430_AUTO_MCBSP2_MASK,
 861                 OMAP3430_PER_MOD,
 862                 CM_AUTOIDLE);
 863
 864         if (omap_rev() > OMAP3430_REV_ES1_0) {
 865                 cm_write_mod_reg(
 866                         OMAP3430ES2_AUTO_USBHOST_MASK,
 867                         OMAP3430ES2_USBHOST_MOD,
 868                         CM_AUTOIDLE);
 869         }
 870
 871         omap_ctrl_writel(OMAP3430_AUTOIDLE_MASK, OMAP2_CONTROL_SYSCONFIG);
 872
 873         /*
 874          * Set all plls to autoidle. This is needed until autoidle is
 875          * enabled by clockfw
 876          */
 877         cm_write_mod_reg(1 << OMAP3430_AUTO_IVA2_DPLL_SHIFT,
 878                          OMAP3430_IVA2_MOD, CM_AUTOIDLE2);
 879         cm_write_mod_reg(1 << OMAP3430_AUTO_MPU_DPLL_SHIFT,
 880                          MPU_MOD,
 881                          CM_AUTOIDLE2);
 882         cm_write_mod_reg((1 << OMAP3430_AUTO_PERIPH_DPLL_SHIFT) |
 883                          (1 << OMAP3430_AUTO_CORE_DPLL_SHIFT),
 884                          PLL_MOD,
 885                          CM_AUTOIDLE);
 886         cm_write_mod_reg(1 << OMAP3430ES2_AUTO_PERIPH2_DPLL_SHIFT,
 887                          PLL_MOD,
 888                          CM_AUTOIDLE2);
 889
 890         /*
 891          * Enable control of expternal oscillator through
 892          * sys_clkreq. In the long run clock framework should
 893          * take care of this.
 894          */
 895         prm_rmw_mod_reg_bits(OMAP_AUTOEXTCLKMODE_MASK,
 896                              1 << OMAP_AUTOEXTCLKMODE_SHIFT,
 897                              OMAP3430_GR_MOD,
 898                              OMAP3_PRM_CLKSRC_CTRL_OFFSET);
 899
 900         /* setup wakup source */
 901         prm_write_mod_reg(OMAP3430_EN_IO_MASK | OMAP3430_EN_GPIO1_MASK |
 902                           OMAP3430_EN_GPT1_MASK | OMAP3430_EN_GPT12_MASK,
 903                           WKUP_MOD, PM_WKEN);
 904         /* No need to write EN_IO, that is always enabled */
 905         prm_write_mod_reg(OMAP3430_GRPSEL_GPIO1_MASK |
 906                           OMAP3430_GRPSEL_GPT1_MASK |
 907                           OMAP3430_GRPSEL_GPT12_MASK,
 908                           WKUP_MOD, OMAP3430_PM_MPUGRPSEL);
 909         /* For some reason IO doesn't generate wakeup event even if
 910          * it is selected to mpu wakeup goup */
 911         prm_write_mod_reg(OMAP3430_IO_EN_MASK | OMAP3430_WKUP_EN_MASK,
 912                           OCP_MOD, OMAP3_PRM_IRQENABLE_MPU_OFFSET);
 913
 914         /* Enable PM_WKEN to support DSS LPR */
 915         prm_write_mod_reg(OMAP3430_PM_WKEN_DSS_EN_DSS_MASK,
 916                                 OMAP3430_DSS_MOD, PM_WKEN);
 917
 918         /* Enable wakeups in PER */
 919         prm_write_mod_reg(OMAP3430_EN_GPIO2_MASK | OMAP3430_EN_GPIO3_MASK |
 920                           OMAP3430_EN_GPIO4_MASK | OMAP3430_EN_GPIO5_MASK |
 921                           OMAP3430_EN_GPIO6_MASK | OMAP3430_EN_UART3_MASK |
 922                           OMAP3430_EN_MCBSP2_MASK | OMAP3430_EN_MCBSP3_MASK |
 923                           OMAP3430_EN_MCBSP4_MASK,
 924                           OMAP3430_PER_MOD, PM_WKEN);
 925         /* and allow them to wake up MPU */
 926         prm_write_mod_reg(OMAP3430_GRPSEL_GPIO2_MASK |
 927                           OMAP3430_GRPSEL_GPIO3_MASK |
 928                           OMAP3430_GRPSEL_GPIO4_MASK |
 929                           OMAP3430_GRPSEL_GPIO5_MASK |
 930                           OMAP3430_GRPSEL_GPIO6_MASK |
 931                           OMAP3430_GRPSEL_UART3_MASK |
 932                           OMAP3430_GRPSEL_MCBSP2_MASK |
 933                           OMAP3430_GRPSEL_MCBSP3_MASK |
 934                           OMAP3430_GRPSEL_MCBSP4_MASK,
 935                           OMAP3430_PER_MOD, OMAP3430_PM_MPUGRPSEL);
 936
 937         /* Don't attach IVA interrupts */
 938         prm_write_mod_reg(0, WKUP_MOD, OMAP3430_PM_IVAGRPSEL);
 939         prm_write_mod_reg(0, CORE_MOD, OMAP3430_PM_IVAGRPSEL1);
 940         prm_write_mod_reg(0, CORE_MOD, OMAP3430ES2_PM_IVAGRPSEL3);
 941         prm_write_mod_reg(0, OMAP3430_PER_MOD, OMAP3430_PM_IVAGRPSEL);
 942
 943         /* Clear any pending 'reset' flags */
 944         prm_write_mod_reg(0xffffffff, MPU_MOD, OMAP2_RM_RSTST);
 945         prm_write_mod_reg(0xffffffff, CORE_MOD, OMAP2_RM_RSTST);
 946         prm_write_mod_reg(0xffffffff, OMAP3430_PER_MOD, OMAP2_RM_RSTST);
 947         prm_write_mod_reg(0xffffffff, OMAP3430_EMU_MOD, OMAP2_RM_RSTST);
 948         prm_write_mod_reg(0xffffffff, OMAP3430_NEON_MOD, OMAP2_RM_RSTST);
 949         prm_write_mod_reg(0xffffffff, OMAP3430_DSS_MOD, OMAP2_RM_RSTST);
 950         prm_write_mod_reg(0xffffffff, OMAP3430ES2_USBHOST_MOD, OMAP2_RM_RSTST);
 951
 952         /* Clear any pending PRCM interrupts */
 953         prm_write_mod_reg(0, OCP_MOD, OMAP3_PRM_IRQSTATUS_MPU_OFFSET);
 954
 955         omap3_iva_idle();
 956         omap3_d2d_idle();
 957 }
 958
 959 void omap3_pm_off_mode_enable(int enable)
 960 {
 961         struct power_state *pwrst;
 962         u32 state;
 963
 964         if (enable)
 965                 state = PWRDM_POWER_OFF;
 966         else
 967                 state = PWRDM_POWER_RET;
 968
 969 #ifdef CONFIG_CPU_IDLE
 970         omap3_cpuidle_update_states();
 971 #endif
 972
 973         list_for_each_entry(pwrst, &pwrst_list, node) {
 974                 pwrst->next_state = state;
 975                 set_pwrdm_state(pwrst->pwrdm, state);
 976         }
 977 }
 978
 979 int omap3_pm_get_suspend_state(struct powerdomain *pwrdm)
 980 {
 981         struct power_state *pwrst;
 982
 983         list_for_each_entry(pwrst, &pwrst_list, node) {
 984                 if (pwrst->pwrdm == pwrdm)
 985                         return pwrst->next_state;
 986         }
 987         return -EINVAL;
 988 }
 989
 990 int omap3_pm_set_suspend_state(struct powerdomain *pwrdm, int state)
 991 {
 992         struct power_state *pwrst;
 993
 994         list_for_each_entry(pwrst, &pwrst_list, node) {
 995                 if (pwrst->pwrdm == pwrdm) {
 996                         pwrst->next_state = state;
 997                         return 0;
 998                 }
 999         }
1000         return -EINVAL;
1001 }
1002
1003 static int __init pwrdms_setup(struct powerdomain *pwrdm, void *unused)
1004 {
1005         struct power_state *pwrst;
1006
1007         if (!pwrdm->pwrsts)
1008                 return 0;
1009
1010         pwrst = kmalloc(sizeof(struct power_state), GFP_ATOMIC);
1011         if (!pwrst)
1012                 return -ENOMEM;
1013         pwrst->pwrdm = pwrdm;
1014         pwrst->next_state = PWRDM_POWER_RET;
1015         list_add(&pwrst->node, &pwrst_list);
1016
1017         if (pwrdm_has_hdwr_sar(pwrdm))
1018                 pwrdm_enable_hdwr_sar(pwrdm);
1019
1020         return set_pwrdm_state(pwrst->pwrdm, pwrst->next_state);
1021 }
1022
1023 /*
1024  * Enable hw supervised mode for all clockdomains if it's
1025  * supported. Initiate sleep transition for other clockdomains, if
1026  * they are not used
1027  */
1028 static int __init clkdms_setup(struct clockdomain *clkdm, void *unused)
1029 {
1030         clkdm_clear_all_wkdeps(clkdm);
1031         clkdm_clear_all_sleepdeps(clkdm);
1032
1033         if (clkdm->flags & CLKDM_CAN_ENABLE_AUTO)
1034                 omap2_clkdm_allow_idle(clkdm);
1035         else if (clkdm->flags & CLKDM_CAN_FORCE_SLEEP &&
1036                  atomic_read(&clkdm->usecount) == 0)
1037                 omap2_clkdm_sleep(clkdm);
1038         return 0;
1039 }
1040
1041 void omap_push_sram_idle(void)
1042 {
1043         _omap_sram_idle = omap_sram_push(omap34xx_cpu_suspend,
1044                                         omap34xx_cpu_suspend_sz);
1045         if (omap_type() != OMAP2_DEVICE_TYPE_GP)
1046                 _omap_save_secure_sram = omap_sram_push(save_secure_ram_context,
1047                                 save_secure_ram_context_sz);
1048 }
1049
1050 static int __init omap3_pm_init(void)
1051 {
1052         struct power_state *pwrst, *tmp;
1053         struct clockdomain *neon_clkdm, *per_clkdm, *mpu_clkdm, *core_clkdm;
1054         int ret;
1055
1056         if (!cpu_is_omap34xx())
1057                 return -ENODEV;
1058
1059         printk(KERN_ERR "Power Management for TI OMAP3.\n");
1060
1061         /* XXX prcm_setup_regs needs to be before enabling hw
1062          * supervised mode for powerdomains */
1063         prcm_setup_regs();
1064
1065         ret = request_irq(INT_34XX_PRCM_MPU_IRQ,
1066                           (irq_handler_t)prcm_interrupt_handler,
1067                           IRQF_DISABLED, "prcm", NULL);
1068         if (ret) {
1069                 printk(KERN_ERR "request_irq failed to register for 0x%x\n",
1070                        INT_34XX_PRCM_MPU_IRQ);
1071                 goto err1;
1072         }
1073
1074         ret = pwrdm_for_each(pwrdms_setup, NULL);
1075         if (ret) {
1076                 printk(KERN_ERR "Failed to setup powerdomains\n");
1077                 goto err2;
1078         }
1079
1080         (void) clkdm_for_each(clkdms_setup, NULL);
1081
1082         mpu_pwrdm = pwrdm_lookup("mpu_pwrdm");
1083         if (mpu_pwrdm == NULL) {
1084                 printk(KERN_ERR "Failed to get mpu_pwrdm\n");
1085                 goto err2;
1086         }
1087
1088         neon_pwrdm = pwrdm_lookup("neon_pwrdm");
1089         per_pwrdm = pwrdm_lookup("per_pwrdm");
1090         core_pwrdm = pwrdm_lookup("core_pwrdm");
1091         cam_pwrdm = pwrdm_lookup("cam_pwrdm");
1092
1093         neon_clkdm = clkdm_lookup("neon_clkdm");
1094         mpu_clkdm = clkdm_lookup("mpu_clkdm");
1095         per_clkdm = clkdm_lookup("per_clkdm");
1096         core_clkdm = clkdm_lookup("core_clkdm");
1097
1098         omap_push_sram_idle();
1099 #ifdef CONFIG_SUSPEND
1100         suspend_set_ops(&omap_pm_ops);
1101 #endif /* CONFIG_SUSPEND */
1102
1103         pm_idle = omap3_pm_idle;
1104         omap3_idle_init();
1105
1106         clkdm_add_wkdep(neon_clkdm, mpu_clkdm);
1107         if (omap_type() != OMAP2_DEVICE_TYPE_GP) {
1108                 omap3_secure_ram_storage =
1109                         kmalloc(0x803F, GFP_KERNEL);
1110                 if (!omap3_secure_ram_storage)
1111                         printk(KERN_ERR "Memory allocation failed when"
1112                                         "allocating for secure sram context\n");
1113
1114                 local_irq_disable();
1115                 local_fiq_disable();
1116
1117                 omap_dma_global_context_save();
1118                 omap3_save_secure_ram_context(PWRDM_POWER_ON);
1119                 omap_dma_global_context_restore();
1120
1121                 local_irq_enable();
1122                 local_fiq_enable();
1123         }
1124
1125         omap3_save_scratchpad_contents();
1126 err1:
1127         return ret;
1128 err2:
1129         free_irq(INT_34XX_PRCM_MPU_IRQ, NULL);
1130         list_for_each_entry_safe(pwrst, tmp, &pwrst_list, node) {
1131                 list_del(&pwrst->node);
1132                 kfree(pwrst);
1133         }
1134         return ret;
1135 }
1136
1137 late_initcall(omap3_pm_init);