arch/arm/mach-omap2/pm24xx.c

   1 /*
   2  * OMAP2 Power Management Routines
   3  *
   4  * Copyright (C) 2005 Texas Instruments, Inc.
   5  * Copyright (C) 2006-2008 Nokia Corporation
   6  *
   7  * Written by:
   8  * Richard Woodruff <r-woodruff2@ti.com>
   9  * Tony Lindgren
  10  * Juha Yrjola
  11  * Amit Kucheria <amit.kucheria@nokia.com>
  12  * Igor Stoppa <igor.stoppa@nokia.com>
  13  *
  14  * Based on pm.c for omap1
  15  *
  16  * This program is free software; you can redistribute it and/or modify
  17  * it under the terms of the GNU General Public License version 2 as
  18  * published by the Free Software Foundation.
  19  */
  20
  21 #include <linux/suspend.h>
  22 #include <linux/sched.h>
  23 #include <linux/proc_fs.h>
  24 #include <linux/interrupt.h>
  25 #include <linux/sysfs.h>
  26 #include <linux/module.h>
  27 #include <linux/delay.h>
  28 #include <linux/clk.h>
  29 #include <linux/io.h>
  30 #include <linux/irq.h>
  31 #include <linux/time.h>
  32 #include <linux/gpio.h>
  33
  34 #include <asm/mach/time.h>
  35 #include <asm/mach/irq.h>
  36 #include <asm/mach-types.h>
  37
  38 #include <mach/irqs.h>
  39 #include <plat/clock.h>
  40 #include <plat/sram.h>
  41 #include <plat/control.h>
  42 #include <plat/mux.h>
  43 #include <plat/dma.h>
  44 #include <plat/board.h>
  45
  46 #include "prm.h"
  47 #include "prm-regbits-24xx.h"
  48 #include "cm.h"
  49 #include "cm-regbits-24xx.h"
  50 #include "sdrc.h"
  51 #include "pm.h"
  52
  53 #include <plat/powerdomain.h>
  54 #include <plat/clockdomain.h>
  55
  56 static void (*omap2_sram_idle)(void);
  57 static void (*omap2_sram_suspend)(u32 dllctrl, void __iomem *sdrc_dlla_ctrl,
  58                                   void __iomem *sdrc_power);
  59
  60 static struct powerdomain *mpu_pwrdm, *core_pwrdm;
  61 static struct clockdomain *dsp_clkdm, *mpu_clkdm, *wkup_clkdm, *gfx_clkdm;
  62
  63 static struct clk *osc_ck, *emul_ck;
  64
  65 static int omap2_fclks_active(void)
  66 {
  67         u32 f1, f2;
  68
  69         f1 = cm_read_mod_reg(CORE_MOD, CM_FCLKEN1);
  70         f2 = cm_read_mod_reg(CORE_MOD, OMAP24XX_CM_FCLKEN2);
  71
  72         /* Ignore UART clocks.  These are handled by UART core (serial.c) */
  73         f1 &= ~(OMAP24XX_EN_UART1_MASK | OMAP24XX_EN_UART2_MASK);
  74         f2 &= ~OMAP24XX_EN_UART3_MASK;
  75
  76         if (f1 | f2)
  77                 return 1;
  78         return 0;
  79 }
  80
  81 static void omap2_enter_full_retention(void)
  82 {
  83         u32 l;
  84         struct timespec ts_preidle, ts_postidle, ts_idle;
  85
  86         /* There is 1 reference hold for all children of the oscillator
  87          * clock, the following will remove it. If no one else uses the
  88          * oscillator itself it will be disabled if/when we enter retention
  89          * mode.
  90          */
  91         clk_disable(osc_ck);
  92
  93         /* Clear old wake-up events */
  94         /* REVISIT: These write to reserved bits? */
  95         prm_write_mod_reg(0xffffffff, CORE_MOD, PM_WKST1);
  96         prm_write_mod_reg(0xffffffff, CORE_MOD, OMAP24XX_PM_WKST2);
  97         prm_write_mod_reg(0xffffffff, WKUP_MOD, PM_WKST);
  98
  99         /*
 100          * Set MPU powerdomain's next power state to RETENTION;
 101          * preserve logic state during retention
 102          */
 103         pwrdm_set_logic_retst(mpu_pwrdm, PWRDM_POWER_RET);
 104         pwrdm_set_next_pwrst(mpu_pwrdm, PWRDM_POWER_RET);
 105
 106         /* Workaround to kill USB */
 107         l = omap_ctrl_readl(OMAP2_CONTROL_DEVCONF0) | OMAP24XX_USBSTANDBYCTRL;
 108         omap_ctrl_writel(l, OMAP2_CONTROL_DEVCONF0);
 109
 110         omap2_gpio_prepare_for_idle(PWRDM_POWER_RET);
 111
 112         if (omap2_pm_debug) {
 113                 omap2_pm_dump(0, 0, 0);
 114                 getnstimeofday(&ts_preidle);
 115         }
 116
 117         /* One last check for pending IRQs to avoid extra latency due
 118          * to sleeping unnecessarily. */
 119         if (omap_irq_pending())
 120                 goto no_sleep;
 121
 122         omap_uart_prepare_idle(0);
 123         omap_uart_prepare_idle(1);
 124         omap_uart_prepare_idle(2);
 125
 126         /* Jump to SRAM suspend code */
 127         omap2_sram_suspend(sdrc_read_reg(SDRC_DLLA_CTRL),
 128                            OMAP_SDRC_REGADDR(SDRC_DLLA_CTRL),
 129                            OMAP_SDRC_REGADDR(SDRC_POWER));
 130
 131         omap_uart_resume_idle(2);
 132         omap_uart_resume_idle(1);
 133         omap_uart_resume_idle(0);
 134
 135 no_sleep:
 136         if (omap2_pm_debug) {
 137                 unsigned long long tmp;
 138
 139                 getnstimeofday(&ts_postidle);
 140                 ts_idle = timespec_sub(ts_postidle, ts_preidle);
 141                 tmp = timespec_to_ns(&ts_idle) * NSEC_PER_USEC;
 142                 omap2_pm_dump(0, 1, tmp);
 143         }
 144         omap2_gpio_resume_after_idle();
 145
 146         clk_enable(osc_ck);
 147
 148         /* clear CORE wake-up events */
 149         prm_write_mod_reg(0xffffffff, CORE_MOD, PM_WKST1);
 150         prm_write_mod_reg(0xffffffff, CORE_MOD, OMAP24XX_PM_WKST2);
 151
 152         /* wakeup domain events - bit 1: GPT1, bit5 GPIO */
 153         prm_clear_mod_reg_bits(0x4 | 0x1, WKUP_MOD, PM_WKST);
 154
 155         /* MPU domain wake events */
 156         l = prm_read_mod_reg(OCP_MOD, OMAP2_PRCM_IRQSTATUS_MPU_OFFSET);
 157         if (l & 0x01)
 158                 prm_write_mod_reg(0x01, OCP_MOD,
 159                                   OMAP2_PRCM_IRQSTATUS_MPU_OFFSET);
 160         if (l & 0x20)
 161                 prm_write_mod_reg(0x20, OCP_MOD,
 162                                   OMAP2_PRCM_IRQSTATUS_MPU_OFFSET);
 163
 164         /* Mask future PRCM-to-MPU interrupts */
 165         prm_write_mod_reg(0x0, OCP_MOD, OMAP2_PRCM_IRQSTATUS_MPU_OFFSET);
 166 }
 167
 168 static int omap2_i2c_active(void)
 169 {
 170         u32 l;
 171
 172         l = cm_read_mod_reg(CORE_MOD, CM_FCLKEN1);
 173         return l & (OMAP2420_EN_I2C2_MASK | OMAP2420_EN_I2C1_MASK);
 174 }
 175
 176 static int sti_console_enabled;
 177
 178 static int omap2_allow_mpu_retention(void)
 179 {
 180         u32 l;
 181
 182         /* Check for MMC, UART2, UART1, McSPI2, McSPI1 and DSS1. */
 183         l = cm_read_mod_reg(CORE_MOD, CM_FCLKEN1);
 184         if (l & (OMAP2420_EN_MMC_MASK | OMAP24XX_EN_UART2_MASK |
 185                  OMAP24XX_EN_UART1_MASK | OMAP24XX_EN_MCSPI2_MASK |
 186                  OMAP24XX_EN_MCSPI1_MASK | OMAP24XX_EN_DSS1_MASK))
 187                 return 0;
 188         /* Check for UART3. */
 189         l = cm_read_mod_reg(CORE_MOD, OMAP24XX_CM_FCLKEN2);
 190         if (l & OMAP24XX_EN_UART3_MASK)
 191                 return 0;
 192         if (sti_console_enabled)
 193                 return 0;
 194
 195         return 1;
 196 }
 197
 198 static void omap2_enter_mpu_retention(void)
 199 {
 200         int only_idle = 0;
 201         struct timespec ts_preidle, ts_postidle, ts_idle;
 202
 203         /* Putting MPU into the WFI state while a transfer is active
 204          * seems to cause the I2C block to timeout. Why? Good question. */
 205         if (omap2_i2c_active())
 206                 return;
 207
 208         /* The peripherals seem not to be able to wake up the MPU when
 209          * it is in retention mode. */
 210         if (omap2_allow_mpu_retention()) {
 211                 /* REVISIT: These write to reserved bits? */
 212                 prm_write_mod_reg(0xffffffff, CORE_MOD, PM_WKST1);
 213                 prm_write_mod_reg(0xffffffff, CORE_MOD, OMAP24XX_PM_WKST2);
 214                 prm_write_mod_reg(0xffffffff, WKUP_MOD, PM_WKST);
 215
 216                 /* Try to enter MPU retention */
 217                 prm_write_mod_reg((0x01 << OMAP_POWERSTATE_SHIFT) |
 218                                   OMAP_LOGICRETSTATE_MASK,
 219                                   MPU_MOD, OMAP2_PM_PWSTCTRL);
 220         } else {
 221                 /* Block MPU retention */
 222
 223                 prm_write_mod_reg(OMAP_LOGICRETSTATE_MASK, MPU_MOD,
 224                                                  OMAP2_PM_PWSTCTRL);
 225                 only_idle = 1;
 226         }
 227
 228         if (omap2_pm_debug) {
 229                 omap2_pm_dump(only_idle ? 2 : 1, 0, 0);
 230                 getnstimeofday(&ts_preidle);
 231         }
 232
 233         omap2_sram_idle();
 234
 235         if (omap2_pm_debug) {
 236                 unsigned long long tmp;
 237
 238                 getnstimeofday(&ts_postidle);
 239                 ts_idle = timespec_sub(ts_postidle, ts_preidle);
 240                 tmp = timespec_to_ns(&ts_idle) * NSEC_PER_USEC;
 241                 omap2_pm_dump(only_idle ? 2 : 1, 1, tmp);
 242         }
 243 }
 244
 245 static int omap2_can_sleep(void)
 246 {
 247         if (omap2_fclks_active())
 248                 return 0;
 249         if (osc_ck->usecount > 1)
 250                 return 0;
 251         if (omap_dma_running())
 252                 return 0;
 253
 254         return 1;
 255 }
 256
 257 static void omap2_pm_idle(void)
 258 {
 259         local_irq_disable();
 260         local_fiq_disable();
 261
 262         if (!omap2_can_sleep()) {
 263                 if (omap_irq_pending())
 264                         goto out;
 265                 omap2_enter_mpu_retention();
 266                 goto out;
 267         }
 268
 269         if (omap_irq_pending())
 270                 goto out;
 271
 272         omap2_enter_full_retention();
 273
 274 out:
 275         local_fiq_enable();
 276         local_irq_enable();
 277 }
 278
 279 static int omap2_pm_prepare(void)
 280 {
 281         /* We cannot sleep in idle until we have resumed */
 282         disable_hlt();
 283         return 0;
 284 }
 285
 286 static int omap2_pm_suspend(void)
 287 {
 288         u32 wken_wkup, mir1;
 289
 290         wken_wkup = prm_read_mod_reg(WKUP_MOD, PM_WKEN);
 291         wken_wkup &= ~OMAP24XX_EN_GPT1_MASK;
 292         prm_write_mod_reg(wken_wkup, WKUP_MOD, PM_WKEN);
 293
 294         /* Mask GPT1 */
 295         mir1 = omap_readl(0x480fe0a4);
 296         omap_writel(1 << 5, 0x480fe0ac);
 297
 298         omap_uart_prepare_suspend();
 299         omap2_enter_full_retention();
 300
 301         omap_writel(mir1, 0x480fe0a4);
 302         prm_write_mod_reg(wken_wkup, WKUP_MOD, PM_WKEN);
 303
 304         return 0;
 305 }
 306
 307 static int omap2_pm_enter(suspend_state_t state)
 308 {
 309         int ret = 0;
 310
 311         switch (state) {
 312         case PM_SUSPEND_STANDBY:
 313         case PM_SUSPEND_MEM:
 314                 ret = omap2_pm_suspend();
 315                 break;
 316         default:
 317                 ret = -EINVAL;
 318         }
 319
 320         return ret;
 321 }
 322
 323 static void omap2_pm_finish(void)
 324 {
 325         enable_hlt();
 326 }
 327
 328 static struct platform_suspend_ops omap_pm_ops = {
 329         .prepare        = omap2_pm_prepare,
 330         .enter          = omap2_pm_enter,
 331         .finish         = omap2_pm_finish,
 332         .valid          = suspend_valid_only_mem,
 333 };
 334
 335 /* XXX This function should be shareable between OMAP2xxx and OMAP3 */
 336 static int __init clkdms_setup(struct clockdomain *clkdm, void *unused)
 337 {
 338         clkdm_clear_all_wkdeps(clkdm);
 339         clkdm_clear_all_sleepdeps(clkdm);
 340
 341         if (clkdm->flags & CLKDM_CAN_ENABLE_AUTO)
 342                 omap2_clkdm_allow_idle(clkdm);
 343         else if (clkdm->flags & CLKDM_CAN_FORCE_SLEEP &&
 344                  atomic_read(&clkdm->usecount) == 0)
 345                 omap2_clkdm_sleep(clkdm);
 346         return 0;
 347 }
 348
 349 static void __init prcm_setup_regs(void)
 350 {
 351         int i, num_mem_banks;
 352         struct powerdomain *pwrdm;
 353
 354         /* Enable autoidle */
 355         prm_write_mod_reg(OMAP24XX_AUTOIDLE_MASK, OCP_MOD,
 356                           OMAP2_PRCM_SYSCONFIG_OFFSET);
 357
 358         /*
 359          * Set CORE powerdomain memory banks to retain their contents
 360          * during RETENTION
 361          */
 362         num_mem_banks = pwrdm_get_mem_bank_count(core_pwrdm);
 363         for (i = 0; i < num_mem_banks; i++)
 364                 pwrdm_set_mem_retst(core_pwrdm, i, PWRDM_POWER_RET);
 365
 366         /* Set CORE powerdomain's next power state to RETENTION */
 367         pwrdm_set_next_pwrst(core_pwrdm, PWRDM_POWER_RET);
 368
 369         /*
 370          * Set MPU powerdomain's next power state to RETENTION;
 371          * preserve logic state during retention
 372          */
 373         pwrdm_set_logic_retst(mpu_pwrdm, PWRDM_POWER_RET);
 374         pwrdm_set_next_pwrst(mpu_pwrdm, PWRDM_POWER_RET);
 375
 376         /* Force-power down DSP, GFX powerdomains */
 377
 378         pwrdm = clkdm_get_pwrdm(dsp_clkdm);
 379         pwrdm_set_next_pwrst(pwrdm, PWRDM_POWER_OFF);
 380         omap2_clkdm_sleep(dsp_clkdm);
 381
 382         pwrdm = clkdm_get_pwrdm(gfx_clkdm);
 383         pwrdm_set_next_pwrst(pwrdm, PWRDM_POWER_OFF);
 384         omap2_clkdm_sleep(gfx_clkdm);
 385
 386         /*
 387          * Clear clockdomain wakeup dependencies and enable
 388          * hardware-supervised idle for all clkdms
 389          */
 390         clkdm_for_each(clkdms_setup, NULL);
 391         clkdm_add_wkdep(mpu_clkdm, wkup_clkdm);
 392
 393         /* Enable clock autoidle for all domains */
 394         cm_write_mod_reg(OMAP24XX_AUTO_CAM_MASK |
 395                          OMAP24XX_AUTO_MAILBOXES_MASK |
 396                          OMAP24XX_AUTO_WDT4_MASK |
 397                          OMAP2420_AUTO_WDT3_MASK |
 398                          OMAP24XX_AUTO_MSPRO_MASK |
 399                          OMAP2420_AUTO_MMC_MASK |
 400                          OMAP24XX_AUTO_FAC_MASK |
 401                          OMAP2420_AUTO_EAC_MASK |
 402                          OMAP24XX_AUTO_HDQ_MASK |
 403                          OMAP24XX_AUTO_UART2_MASK |
 404                          OMAP24XX_AUTO_UART1_MASK |
 405                          OMAP24XX_AUTO_I2C2_MASK |
 406                          OMAP24XX_AUTO_I2C1_MASK |
 407                          OMAP24XX_AUTO_MCSPI2_MASK |
 408                          OMAP24XX_AUTO_MCSPI1_MASK |
 409                          OMAP24XX_AUTO_MCBSP2_MASK |
 410                          OMAP24XX_AUTO_MCBSP1_MASK |
 411                          OMAP24XX_AUTO_GPT12_MASK |
 412                          OMAP24XX_AUTO_GPT11_MASK |
 413                          OMAP24XX_AUTO_GPT10_MASK |
 414                          OMAP24XX_AUTO_GPT9_MASK |
 415                          OMAP24XX_AUTO_GPT8_MASK |
 416                          OMAP24XX_AUTO_GPT7_MASK |
 417                          OMAP24XX_AUTO_GPT6_MASK |
 418                          OMAP24XX_AUTO_GPT5_MASK |
 419                          OMAP24XX_AUTO_GPT4_MASK |
 420                          OMAP24XX_AUTO_GPT3_MASK |
 421                          OMAP24XX_AUTO_GPT2_MASK |
 422                          OMAP2420_AUTO_VLYNQ_MASK |
 423                          OMAP24XX_AUTO_DSS_MASK,
 424                          CORE_MOD, CM_AUTOIDLE1);
 425         cm_write_mod_reg(OMAP24XX_AUTO_UART3_MASK |
 426                          OMAP24XX_AUTO_SSI_MASK |
 427                          OMAP24XX_AUTO_USB_MASK,
 428                          CORE_MOD, CM_AUTOIDLE2);
 429         cm_write_mod_reg(OMAP24XX_AUTO_SDRC_MASK |
 430                          OMAP24XX_AUTO_GPMC_MASK |
 431                          OMAP24XX_AUTO_SDMA_MASK,
 432                          CORE_MOD, CM_AUTOIDLE3);
 433         cm_write_mod_reg(OMAP24XX_AUTO_PKA_MASK |
 434                          OMAP24XX_AUTO_AES_MASK |
 435                          OMAP24XX_AUTO_RNG_MASK |
 436                          OMAP24XX_AUTO_SHA_MASK |
 437                          OMAP24XX_AUTO_DES_MASK,
 438                          CORE_MOD, OMAP24XX_CM_AUTOIDLE4);
 439
 440         cm_write_mod_reg(OMAP2420_AUTO_DSP_IPI_MASK, OMAP24XX_DSP_MOD,
 441                          CM_AUTOIDLE);
 442
 443         /* Put DPLL and both APLLs into autoidle mode */
 444         cm_write_mod_reg((0x03 << OMAP24XX_AUTO_DPLL_SHIFT) |
 445                          (0x03 << OMAP24XX_AUTO_96M_SHIFT) |
 446                          (0x03 << OMAP24XX_AUTO_54M_SHIFT),
 447                          PLL_MOD, CM_AUTOIDLE);
 448
 449         cm_write_mod_reg(OMAP24XX_AUTO_OMAPCTRL_MASK |
 450                          OMAP24XX_AUTO_WDT1_MASK |
 451                          OMAP24XX_AUTO_MPU_WDT_MASK |
 452                          OMAP24XX_AUTO_GPIOS_MASK |
 453                          OMAP24XX_AUTO_32KSYNC_MASK |
 454                          OMAP24XX_AUTO_GPT1_MASK,
 455                          WKUP_MOD, CM_AUTOIDLE);
 456
 457         /* REVISIT: Configure number of 32 kHz clock cycles for sys_clk
 458          * stabilisation */
 459         prm_write_mod_reg(15 << OMAP_SETUP_TIME_SHIFT, OMAP24XX_GR_MOD,
 460                           OMAP2_PRCM_CLKSSETUP_OFFSET);
 461
 462         /* Configure automatic voltage transition */
 463         prm_write_mod_reg(2 << OMAP_SETUP_TIME_SHIFT, OMAP24XX_GR_MOD,
 464                           OMAP2_PRCM_VOLTSETUP_OFFSET);
 465         prm_write_mod_reg(OMAP24XX_AUTO_EXTVOLT_MASK |
 466                           (0x1 << OMAP24XX_SETOFF_LEVEL_SHIFT) |
 467                           OMAP24XX_MEMRETCTRL_MASK |
 468                           (0x1 << OMAP24XX_SETRET_LEVEL_SHIFT) |
 469                           (0x0 << OMAP24XX_VOLT_LEVEL_SHIFT),
 470                           OMAP24XX_GR_MOD, OMAP2_PRCM_VOLTCTRL_OFFSET);
 471
 472         /* Enable wake-up events */
 473         prm_write_mod_reg(OMAP24XX_EN_GPIOS_MASK | OMAP24XX_EN_GPT1_MASK,
 474                           WKUP_MOD, PM_WKEN);
 475 }
 476
 477 static int __init omap2_pm_init(void)
 478 {
 479         u32 l;
 480
 481         if (!cpu_is_omap24xx())
 482                 return -ENODEV;
 483
 484         printk(KERN_INFO "Power Management for OMAP2 initializing\n");
 485         l = prm_read_mod_reg(OCP_MOD, OMAP2_PRCM_REVISION_OFFSET);
 486         printk(KERN_INFO "PRCM revision %d.%d\n", (l >> 4) & 0x0f, l & 0x0f);
 487
 488         /* Look up important powerdomains */
 489
 490         mpu_pwrdm = pwrdm_lookup("mpu_pwrdm");
 491         if (!mpu_pwrdm)
 492                 pr_err("PM: mpu_pwrdm not found\n");
 493
 494         core_pwrdm = pwrdm_lookup("core_pwrdm");
 495         if (!core_pwrdm)
 496                 pr_err("PM: core_pwrdm not found\n");
 497
 498         /* Look up important clockdomains */
 499
 500         mpu_clkdm = clkdm_lookup("mpu_clkdm");
 501         if (!mpu_clkdm)
 502                 pr_err("PM: mpu_clkdm not found\n");
 503
 504         wkup_clkdm = clkdm_lookup("wkup_clkdm");
 505         if (!wkup_clkdm)
 506                 pr_err("PM: wkup_clkdm not found\n");
 507
 508         dsp_clkdm = clkdm_lookup("dsp_clkdm");
 509         if (!dsp_clkdm)
 510                 pr_err("PM: dsp_clkdm not found\n");
 511
 512         gfx_clkdm = clkdm_lookup("gfx_clkdm");
 513         if (!gfx_clkdm)
 514                 pr_err("PM: gfx_clkdm not found\n");
 515
 516
 517         osc_ck = clk_get(NULL, "osc_ck");
 518         if (IS_ERR(osc_ck)) {
 519                 printk(KERN_ERR "could not get osc_ck\n");
 520                 return -ENODEV;
 521         }
 522
 523         if (cpu_is_omap242x()) {
 524                 emul_ck = clk_get(NULL, "emul_ck");
 525                 if (IS_ERR(emul_ck)) {
 526                         printk(KERN_ERR "could not get emul_ck\n");
 527                         clk_put(osc_ck);
 528                         return -ENODEV;
 529                 }
 530         }
 531
 532         prcm_setup_regs();
 533
 534         /* Hack to prevent MPU retention when STI console is enabled. */
 535         {
 536                 const struct omap_sti_console_config *sti;
 537
 538                 sti = omap_get_config(OMAP_TAG_STI_CONSOLE,
 539                                       struct omap_sti_console_config);
 540                 if (sti != NULL && sti->enable)
 541                         sti_console_enabled = 1;
 542         }
 543
 544         /*
 545          * We copy the assembler sleep/wakeup routines to SRAM.
 546          * These routines need to be in SRAM as that's the only
 547          * memory the MPU can see when it wakes up.
 548          */
 549         if (cpu_is_omap24xx()) {
 550                 omap2_sram_idle = omap_sram_push(omap24xx_idle_loop_suspend,
 551                                                  omap24xx_idle_loop_suspend_sz);
 552
 553                 omap2_sram_suspend = omap_sram_push(omap24xx_cpu_suspend,
 554                                                     omap24xx_cpu_suspend_sz);
 555         }
 556
 557         suspend_set_ops(&omap_pm_ops);
 558         pm_idle = omap2_pm_idle;
 559
 560         return 0;
 561 }
 562
 563 late_initcall(omap2_pm_init);