arch/arm/mach-mx3/pcm037.c

   1 /*
   2  *  Copyright (C) 2008 Sascha Hauer, Pengutronix
   3  *
   4  * This program is free software; you can redistribute it and/or modify
   5  * it under the terms of the GNU General Public License as published by
   6  * the Free Software Foundation; either version 2 of the License, or
   7  * (at your option) any later version.
   8  *
   9  * This program is distributed in the hope that it will be useful,
  10  * but WITHOUT ANY WARRANTY; without even the implied warranty of
  11  * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
  12  * GNU General Public License for more details.
  13  *
  14  * You should have received a copy of the GNU General Public License
  15  * along with this program; if not, write to the Free Software
  16  * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA  02111-1307  USA
  17  */
  18
  19 #include <linux/types.h>
  20 #include <linux/init.h>
  21
  22 #include <linux/platform_device.h>
  23 #include <linux/mtd/physmap.h>
  24 #include <linux/mtd/plat-ram.h>
  25 #include <linux/memory.h>
  26 #include <linux/gpio.h>
  27 #include <linux/smsc911x.h>
  28 #include <linux/interrupt.h>
  29 #include <linux/i2c.h>
  30 #include <linux/i2c/at24.h>
  31 #include <linux/delay.h>
  32 #include <linux/spi/spi.h>
  33 #include <linux/irq.h>
  34 #include <linux/fsl_devices.h>
  35
  36 #include <mach/hardware.h>
  37 #include <asm/mach-types.h>
  38 #include <asm/mach/arch.h>
  39 #include <asm/mach/time.h>
  40 #include <asm/mach/map.h>
  41 #include <mach/common.h>
  42 #include <mach/imx-uart.h>
  43 #include <mach/iomux-mx3.h>
  44 #include <mach/ipu.h>
  45 #include <mach/board-pcm037.h>
  46 #include <mach/mx3fb.h>
  47 #include <mach/mxc_nand.h>
  48 #include <mach/mmc.h>
  49 #ifdef CONFIG_I2C_IMX
  50 #include <mach/i2c.h>
  51 #endif
  52
  53 #include "devices.h"
  54
  55 static unsigned int pcm037_pins[] = {
  56         /* I2C */
  57         MX31_PIN_CSPI2_MOSI__SCL,
  58         MX31_PIN_CSPI2_MISO__SDA,
  59         /* SDHC1 */
  60         MX31_PIN_SD1_DATA3__SD1_DATA3,
  61         MX31_PIN_SD1_DATA2__SD1_DATA2,
  62         MX31_PIN_SD1_DATA1__SD1_DATA1,
  63         MX31_PIN_SD1_DATA0__SD1_DATA0,
  64         MX31_PIN_SD1_CLK__SD1_CLK,
  65         MX31_PIN_SD1_CMD__SD1_CMD,
  66         IOMUX_MODE(MX31_PIN_SCK6, IOMUX_CONFIG_GPIO), /* card detect */
  67         IOMUX_MODE(MX31_PIN_SFS6, IOMUX_CONFIG_GPIO), /* write protect */
  68         /* SPI1 */
  69         MX31_PIN_CSPI1_MOSI__MOSI,
  70         MX31_PIN_CSPI1_MISO__MISO,
  71         MX31_PIN_CSPI1_SCLK__SCLK,
  72         MX31_PIN_CSPI1_SPI_RDY__SPI_RDY,
  73         MX31_PIN_CSPI1_SS0__SS0,
  74         MX31_PIN_CSPI1_SS1__SS1,
  75         MX31_PIN_CSPI1_SS2__SS2,
  76         /* UART1 */
  77         MX31_PIN_CTS1__CTS1,
  78         MX31_PIN_RTS1__RTS1,
  79         MX31_PIN_TXD1__TXD1,
  80         MX31_PIN_RXD1__RXD1,
  81         /* UART2 */
  82         MX31_PIN_TXD2__TXD2,
  83         MX31_PIN_RXD2__RXD2,
  84         MX31_PIN_CTS2__CTS2,
  85         MX31_PIN_RTS2__RTS2,
  86         /* UART3 */
  87         MX31_PIN_CSPI3_MOSI__RXD3,
  88         MX31_PIN_CSPI3_MISO__TXD3,
  89         MX31_PIN_CSPI3_SCLK__RTS3,
  90         MX31_PIN_CSPI3_SPI_RDY__CTS3,
  91         /* LAN9217 irq pin */
  92         IOMUX_MODE(MX31_PIN_GPIO3_1, IOMUX_CONFIG_GPIO),
  93         /* Onewire */
  94         MX31_PIN_BATT_LINE__OWIRE,
  95         /* Framebuffer */
  96         MX31_PIN_LD0__LD0,
  97         MX31_PIN_LD1__LD1,
  98         MX31_PIN_LD2__LD2,
  99         MX31_PIN_LD3__LD3,
 100         MX31_PIN_LD4__LD4,
 101         MX31_PIN_LD5__LD5,
 102         MX31_PIN_LD6__LD6,
 103         MX31_PIN_LD7__LD7,
 104         MX31_PIN_LD8__LD8,
 105         MX31_PIN_LD9__LD9,
 106         MX31_PIN_LD10__LD10,
 107         MX31_PIN_LD11__LD11,
 108         MX31_PIN_LD12__LD12,
 109         MX31_PIN_LD13__LD13,
 110         MX31_PIN_LD14__LD14,
 111         MX31_PIN_LD15__LD15,
 112         MX31_PIN_LD16__LD16,
 113         MX31_PIN_LD17__LD17,
 114         MX31_PIN_VSYNC3__VSYNC3,
 115         MX31_PIN_HSYNC__HSYNC,
 116         MX31_PIN_FPSHIFT__FPSHIFT,
 117         MX31_PIN_DRDY0__DRDY0,
 118         MX31_PIN_D3_REV__D3_REV,
 119         MX31_PIN_CONTRAST__CONTRAST,
 120         MX31_PIN_D3_SPL__D3_SPL,
 121         MX31_PIN_D3_CLS__D3_CLS,
 122         MX31_PIN_LCS0__GPI03_23,
 123 };
 124
 125 static struct physmap_flash_data pcm037_flash_data = {
 126         .width  = 2,
 127 };
 128
 129 static struct resource pcm037_flash_resource = {
 130         .start  = 0xa0000000,
 131         .end    = 0xa1ffffff,
 132         .flags  = IORESOURCE_MEM,
 133 };
 134
 135 static int usbotg_pins[] = {
 136         MX31_PIN_USBOTG_DATA0__USBOTG_DATA0,
 137         MX31_PIN_USBOTG_DATA1__USBOTG_DATA1,
 138         MX31_PIN_USBOTG_DATA2__USBOTG_DATA2,
 139         MX31_PIN_USBOTG_DATA3__USBOTG_DATA3,
 140         MX31_PIN_USBOTG_DATA4__USBOTG_DATA4,
 141         MX31_PIN_USBOTG_DATA5__USBOTG_DATA5,
 142         MX31_PIN_USBOTG_DATA6__USBOTG_DATA6,
 143         MX31_PIN_USBOTG_DATA7__USBOTG_DATA7,
 144         MX31_PIN_USBOTG_CLK__USBOTG_CLK,
 145         MX31_PIN_USBOTG_DIR__USBOTG_DIR,
 146         MX31_PIN_USBOTG_NXT__USBOTG_NXT,
 147         MX31_PIN_USBOTG_STP__USBOTG_STP,
 148 };
 149
 150 /* USB OTG HS port */
 151 static int __init gpio_usbotg_hs_activate(void)
 152 {
 153         int ret = mxc_iomux_setup_multiple_pins(usbotg_pins,
 154                                         ARRAY_SIZE(usbotg_pins), "usbotg");
 155
 156         if (ret < 0) {
 157                 printk(KERN_ERR "Cannot set up OTG pins\n");
 158                 return ret;
 159         }
 160
 161         mxc_iomux_set_pad(MX31_PIN_USBOTG_DATA0, PAD_CTL_DRV_MAX | PAD_CTL_SRE_FAST);
 162         mxc_iomux_set_pad(MX31_PIN_USBOTG_DATA1, PAD_CTL_DRV_MAX | PAD_CTL_SRE_FAST);
 163         mxc_iomux_set_pad(MX31_PIN_USBOTG_DATA2, PAD_CTL_DRV_MAX | PAD_CTL_SRE_FAST);
 164         mxc_iomux_set_pad(MX31_PIN_USBOTG_DATA3, PAD_CTL_DRV_MAX | PAD_CTL_SRE_FAST);
 165         mxc_iomux_set_pad(MX31_PIN_USBOTG_DATA4, PAD_CTL_DRV_MAX | PAD_CTL_SRE_FAST);
 166         mxc_iomux_set_pad(MX31_PIN_USBOTG_DATA5, PAD_CTL_DRV_MAX | PAD_CTL_SRE_FAST);
 167         mxc_iomux_set_pad(MX31_PIN_USBOTG_DATA6, PAD_CTL_DRV_MAX | PAD_CTL_SRE_FAST);
 168         mxc_iomux_set_pad(MX31_PIN_USBOTG_DATA7, PAD_CTL_DRV_MAX | PAD_CTL_SRE_FAST);
 169         mxc_iomux_set_pad(MX31_PIN_USBOTG_CLK,   PAD_CTL_DRV_MAX | PAD_CTL_SRE_FAST);
 170         mxc_iomux_set_pad(MX31_PIN_USBOTG_DIR,   PAD_CTL_DRV_MAX | PAD_CTL_SRE_FAST);
 171         mxc_iomux_set_pad(MX31_PIN_USBOTG_NXT,   PAD_CTL_DRV_MAX | PAD_CTL_SRE_FAST);
 172         mxc_iomux_set_pad(MX31_PIN_USBOTG_STP,   PAD_CTL_DRV_MAX | PAD_CTL_SRE_FAST);
 173
 174         return 0;
 175 }
 176
 177 /* OTG config */
 178 static struct fsl_usb2_platform_data usb_pdata = {
 179         .operating_mode = FSL_USB2_DR_DEVICE,
 180         .phy_mode       = FSL_USB2_PHY_ULPI,
 181 };
 182
 183 static struct platform_device pcm037_flash = {
 184         .name   = "physmap-flash",
 185         .id     = 0,
 186         .dev    = {
 187                 .platform_data  = &pcm037_flash_data,
 188         },
 189         .resource = &pcm037_flash_resource,
 190         .num_resources = 1,
 191 };
 192
 193 static struct imxuart_platform_data uart_pdata = {
 194         .flags = IMXUART_HAVE_RTSCTS,
 195 };
 196
 197 static struct resource smsc911x_resources[] = {
 198         [0] = {
 199                 .start          = CS1_BASE_ADDR + 0x300,
 200                 .end            = CS1_BASE_ADDR + 0x300 + SZ_64K - 1,
 201                 .flags          = IORESOURCE_MEM,
 202         },
 203         [1] = {
 204                 .start          = IOMUX_TO_IRQ(MX31_PIN_GPIO3_1),
 205                 .end            = IOMUX_TO_IRQ(MX31_PIN_GPIO3_1),
 206                 .flags          = IORESOURCE_IRQ | IORESOURCE_IRQ_LOWLEVEL,
 207         },
 208 };
 209
 210 static struct smsc911x_platform_config smsc911x_info = {
 211         .flags          = SMSC911X_USE_32BIT | SMSC911X_FORCE_INTERNAL_PHY |
 212                           SMSC911X_SAVE_MAC_ADDRESS,
 213         .irq_polarity   = SMSC911X_IRQ_POLARITY_ACTIVE_LOW,
 214         .irq_type       = SMSC911X_IRQ_TYPE_OPEN_DRAIN,
 215         .phy_interface  = PHY_INTERFACE_MODE_MII,
 216 };
 217
 218 static struct platform_device pcm037_eth = {
 219         .name           = "smsc911x",
 220         .id             = -1,
 221         .num_resources  = ARRAY_SIZE(smsc911x_resources),
 222         .resource       = smsc911x_resources,
 223         .dev            = {
 224                 .platform_data = &smsc911x_info,
 225         },
 226 };
 227
 228 static struct platdata_mtd_ram pcm038_sram_data = {
 229         .bankwidth = 2,
 230 };
 231
 232 static struct resource pcm038_sram_resource = {
 233         .start = CS4_BASE_ADDR,
 234         .end   = CS4_BASE_ADDR + 512 * 1024 - 1,
 235         .flags = IORESOURCE_MEM,
 236 };
 237
 238 static struct platform_device pcm037_sram_device = {
 239         .name = "mtd-ram",
 240         .id = 0,
 241         .dev = {
 242                 .platform_data = &pcm038_sram_data,
 243         },
 244         .num_resources = 1,
 245         .resource = &pcm038_sram_resource,
 246 };
 247
 248 static struct mxc_nand_platform_data pcm037_nand_board_info = {
 249         .width = 1,
 250         .hw_ecc = 1,
 251 };
 252
 253 #ifdef CONFIG_I2C_IMX
 254 static struct imxi2c_platform_data pcm037_i2c_1_data = {
 255         .bitrate = 100000,
 256 };
 257
 258 static struct at24_platform_data board_eeprom = {
 259         .byte_len = 4096,
 260         .page_size = 32,
 261         .flags = AT24_FLAG_ADDR16,
 262 };
 263
 264 static struct i2c_board_info pcm037_i2c_devices[] = {
 265        {
 266                 I2C_BOARD_INFO("at24", 0x52), /* E0=0, E1=1, E2=0 */
 267                 .platform_data = &board_eeprom,
 268         }, {
 269                 I2C_BOARD_INFO("rtc-pcf8563", 0x51),
 270                 .type = "pcf8563",
 271         }
 272 };
 273 #endif
 274
 275 /* Not connected by default */
 276 #ifdef PCM970_SDHC_RW_SWITCH
 277 static int pcm970_sdhc1_get_ro(struct device *dev)
 278 {
 279         return gpio_get_value(IOMUX_TO_GPIO(MX31_PIN_SFS6));
 280 }
 281 #endif
 282
 283 #define SDHC1_GPIO_WP   IOMUX_TO_GPIO(MX31_PIN_SFS6)
 284 #define SDHC1_GPIO_DET  IOMUX_TO_GPIO(MX31_PIN_SCK6)
 285
 286 static int pcm970_sdhc1_init(struct device *dev, irq_handler_t detect_irq,
 287                 void *data)
 288 {
 289         int ret;
 290
 291         ret = gpio_request(SDHC1_GPIO_DET, "sdhc-detect");
 292         if (ret)
 293                 return ret;
 294
 295         gpio_direction_input(SDHC1_GPIO_DET);
 296
 297 #ifdef PCM970_SDHC_RW_SWITCH
 298         ret = gpio_request(SDHC1_GPIO_WP, "sdhc-wp");
 299         if (ret)
 300                 goto err_gpio_free;
 301         gpio_direction_input(SDHC1_GPIO_WP);
 302 #endif
 303
 304         ret = request_irq(IOMUX_TO_IRQ(MX31_PIN_SCK6), detect_irq,
 305                         IRQF_DISABLED | IRQF_TRIGGER_FALLING,
 306                                 "sdhc-detect", data);
 307         if (ret)
 308                 goto err_gpio_free_2;
 309
 310         return 0;
 311
 312 err_gpio_free_2:
 313 #ifdef PCM970_SDHC_RW_SWITCH
 314         gpio_free(SDHC1_GPIO_WP);
 315 err_gpio_free:
 316 #endif
 317         gpio_free(SDHC1_GPIO_DET);
 318
 319         return ret;
 320 }
 321
 322 static void pcm970_sdhc1_exit(struct device *dev, void *data)
 323 {
 324         free_irq(IOMUX_TO_IRQ(MX31_PIN_SCK6), data);
 325         gpio_free(SDHC1_GPIO_DET);
 326         gpio_free(SDHC1_GPIO_WP);
 327 }
 328
 329 static struct imxmmc_platform_data sdhc_pdata = {
 330 #ifdef PCM970_SDHC_RW_SWITCH
 331         .get_ro = pcm970_sdhc1_get_ro,
 332 #endif
 333         .init = pcm970_sdhc1_init,
 334         .exit = pcm970_sdhc1_exit,
 335 };
 336
 337 static struct platform_device *devices[] __initdata = {
 338         &pcm037_flash,
 339         &pcm037_sram_device,
 340 };
 341
 342 static struct ipu_platform_data mx3_ipu_data = {
 343         .irq_base = MXC_IPU_IRQ_START,
 344 };
 345
 346 static const struct fb_videomode fb_modedb[] = {
 347         {
 348                 /* 240x320 @ 60 Hz Sharp */
 349                 .name           = "Sharp-LQ035Q7DH06-QVGA",
 350                 .refresh        = 60,
 351                 .xres           = 240,
 352                 .yres           = 320,
 353                 .pixclock       = 185925,
 354                 .left_margin    = 9,
 355                 .right_margin   = 16,
 356                 .upper_margin   = 7,
 357                 .lower_margin   = 9,
 358                 .hsync_len      = 1,
 359                 .vsync_len      = 1,
 360                 .sync           = FB_SYNC_HOR_HIGH_ACT | FB_SYNC_SHARP_MODE |
 361                                   FB_SYNC_CLK_INVERT | FB_SYNC_CLK_IDLE_EN,
 362                 .vmode          = FB_VMODE_NONINTERLACED,
 363                 .flag           = 0,
 364         }, {
 365                 /* 240x320 @ 60 Hz */
 366                 .name           = "TX090",
 367                 .refresh        = 60,
 368                 .xres           = 240,
 369                 .yres           = 320,
 370                 .pixclock       = 38255,
 371                 .left_margin    = 144,
 372                 .right_margin   = 0,
 373                 .upper_margin   = 7,
 374                 .lower_margin   = 40,
 375                 .hsync_len      = 96,
 376                 .vsync_len      = 1,
 377                 .sync           = FB_SYNC_VERT_HIGH_ACT | FB_SYNC_OE_ACT_HIGH,
 378                 .vmode          = FB_VMODE_NONINTERLACED,
 379                 .flag           = 0,
 380         },
 381 };
 382
 383 static struct mx3fb_platform_data mx3fb_pdata = {
 384         .dma_dev        = &mx3_ipu.dev,
 385         .name           = "Sharp-LQ035Q7DH06-QVGA",
 386         .mode           = fb_modedb,
 387         .num_modes      = ARRAY_SIZE(fb_modedb),
 388 };
 389
 390 /*
 391  * Board specific initialization.
 392  */
 393 static void __init mxc_board_init(void)
 394 {
 395         int ret;
 396
 397         mxc_iomux_setup_multiple_pins(pcm037_pins, ARRAY_SIZE(pcm037_pins),
 398                         "pcm037");
 399
 400         platform_add_devices(devices, ARRAY_SIZE(devices));
 401
 402         mxc_register_device(&mxc_uart_device0, &uart_pdata);
 403         mxc_register_device(&mxc_uart_device1, &uart_pdata);
 404         mxc_register_device(&mxc_uart_device2, &uart_pdata);
 405
 406         mxc_register_device(&mxc_w1_master_device, NULL);
 407
 408         /* LAN9217 IRQ pin */
 409         ret = gpio_request(IOMUX_TO_GPIO(MX31_PIN_GPIO3_1), "lan9217-irq");
 410         if (ret)
 411                 pr_warning("could not get LAN irq gpio\n");
 412         else {
 413                 gpio_direction_input(IOMUX_TO_GPIO(MX31_PIN_GPIO3_1));
 414                 platform_device_register(&pcm037_eth);
 415         }
 416
 417
 418 #ifdef CONFIG_I2C_IMX
 419         i2c_register_board_info(1, pcm037_i2c_devices,
 420                         ARRAY_SIZE(pcm037_i2c_devices));
 421
 422         mxc_register_device(&mxc_i2c_device1, &pcm037_i2c_1_data);
 423 #endif
 424         mxc_register_device(&mxc_nand_device, &pcm037_nand_board_info);
 425         mxc_register_device(&mxcsdhc_device0, &sdhc_pdata);
 426         mxc_register_device(&mx3_ipu, &mx3_ipu_data);
 427         mxc_register_device(&mx3_fb, &mx3fb_pdata);
 428         if (!gpio_usbotg_hs_activate())
 429                 mxc_register_device(&mxc_otg_udc_device, &usb_pdata);
 430 }
 431
 432 static void __init pcm037_timer_init(void)
 433 {
 434         mx31_clocks_init(26000000);
 435 }
 436
 437 struct sys_timer pcm037_timer = {
 438         .init   = pcm037_timer_init,
 439 };
 440
 441 MACHINE_START(PCM037, "Phytec Phycore pcm037")
 442         /* Maintainer: Pengutronix */
 443         .phys_io        = AIPS1_BASE_ADDR,
 444         .io_pg_offst    = ((AIPS1_BASE_ADDR_VIRT) >> 18) & 0xfffc,
 445         .boot_params    = PHYS_OFFSET + 0x100,
 446         .map_io         = mx31_map_io,
 447         .init_irq       = mxc_init_irq,
 448         .init_machine   = mxc_board_init,
 449         .timer          = &pcm037_timer,
 450 MACHINE_END
 451