arch/arm/mach-ixp4xx/ixdp425-setup.c

   1 /*
   2  * arch/arm/mach-ixp4xx/ixdp425-setup.c
   3  *
   4  * IXDP425/IXCDP1100 board-setup
   5  *
   6  * Copyright (C) 2003-2005 MontaVista Software, Inc.
   7  *
   8  * Author: Deepak Saxena <dsaxena@plexity.net>
   9  */
  10
  11 #include <linux/kernel.h>
  12 #include <linux/init.h>
  13 #include <linux/device.h>
  14 #include <linux/serial.h>
  15 #include <linux/tty.h>
  16 #include <linux/serial_8250.h>
  17 #include <linux/i2c-gpio.h>
  18 #include <linux/io.h>
  19 #include <linux/mtd/mtd.h>
  20 #include <linux/mtd/nand.h>
  21 #include <linux/mtd/partitions.h>
  22 #include <linux/delay.h>
  23 #include <asm/types.h>
  24 #include <asm/setup.h>
  25 #include <asm/memory.h>
  26 #include <mach/hardware.h>
  27 #include <asm/mach-types.h>
  28 #include <asm/irq.h>
  29 #include <asm/mach/arch.h>
  30 #include <asm/mach/flash.h>
  31
  32 #define IXDP425_SDA_PIN         7
  33 #define IXDP425_SCL_PIN         6
  34
  35 /* NAND Flash pins */
  36 #define IXDP425_NAND_NCE_PIN    12
  37
  38 #define IXDP425_NAND_CMD_BYTE   0x01
  39 #define IXDP425_NAND_ADDR_BYTE  0x02
  40
  41 static struct flash_platform_data ixdp425_flash_data = {
  42         .map_name       = "cfi_probe",
  43         .width          = 2,
  44 };
  45
  46 static struct resource ixdp425_flash_resource = {
  47         .flags          = IORESOURCE_MEM,
  48 };
  49
  50 static struct platform_device ixdp425_flash = {
  51         .name           = "IXP4XX-Flash",
  52         .id             = 0,
  53         .dev            = {
  54                 .platform_data = &ixdp425_flash_data,
  55         },
  56         .num_resources  = 1,
  57         .resource       = &ixdp425_flash_resource,
  58 };
  59
  60 #if defined(CONFIG_MTD_NAND_PLATFORM) || \
  61     defined(CONFIG_MTD_NAND_PLATFORM_MODULE)
  62
  63 const char *part_probes[] = { "cmdlinepart", NULL };
  64
  65 static struct mtd_partition ixdp425_partitions[] = {
  66         {
  67                 .name   = "ixp400 NAND FS 0",
  68                 .offset = 0,
  69                 .size   = SZ_8M
  70         }, {
  71                 .name   = "ixp400 NAND FS 1",
  72                 .offset = MTDPART_OFS_APPEND,
  73                 .size   = MTDPART_SIZ_FULL
  74         },
  75 };
  76
  77 static void
  78 ixdp425_flash_nand_cmd_ctrl(struct mtd_info *mtd, int cmd, unsigned int ctrl)
  79 {
  80         struct nand_chip *this = mtd->priv;
  81         int offset = (int)this->priv;
  82
  83         if (ctrl & NAND_CTRL_CHANGE) {
  84                 if (ctrl & NAND_NCE) {
  85                         gpio_line_set(IXDP425_NAND_NCE_PIN, IXP4XX_GPIO_LOW);
  86                         udelay(5);
  87                 } else
  88                         gpio_line_set(IXDP425_NAND_NCE_PIN, IXP4XX_GPIO_HIGH);
  89
  90                 offset = (ctrl & NAND_CLE) ? IXDP425_NAND_CMD_BYTE : 0;
  91                 offset |= (ctrl & NAND_ALE) ? IXDP425_NAND_ADDR_BYTE : 0;
  92                 this->priv = (void *)offset;
  93         }
  94
  95         if (cmd != NAND_CMD_NONE)
  96                 writeb(cmd, this->IO_ADDR_W + offset);
  97 }
  98
  99 static struct platform_nand_data ixdp425_flash_nand_data = {
 100         .chip = {
 101                 .nr_chips               = 1,
 102                 .chip_delay             = 30,
 103                 .options                = NAND_NO_AUTOINCR,
 104                 .part_probe_types       = part_probes,
 105                 .partitions             = ixdp425_partitions,
 106                 .nr_partitions          = ARRAY_SIZE(ixdp425_partitions),
 107         },
 108         .ctrl = {
 109                 .cmd_ctrl               = ixdp425_flash_nand_cmd_ctrl
 110         }
 111 };
 112
 113 static struct resource ixdp425_flash_nand_resource = {
 114         .flags          = IORESOURCE_MEM,
 115 };
 116
 117 static struct platform_device ixdp425_flash_nand = {
 118         .name           = "gen_nand",
 119         .id             = -1,
 120         .dev            = {
 121                 .platform_data = &ixdp425_flash_nand_data,
 122         },
 123         .num_resources  = 1,
 124         .resource       = &ixdp425_flash_nand_resource,
 125 };
 126 #endif  /* CONFIG_MTD_NAND_PLATFORM */
 127
 128 static struct i2c_gpio_platform_data ixdp425_i2c_gpio_data = {
 129         .sda_pin        = IXDP425_SDA_PIN,
 130         .scl_pin        = IXDP425_SCL_PIN,
 131 };
 132
 133 static struct platform_device ixdp425_i2c_gpio = {
 134         .name           = "i2c-gpio",
 135         .id             = 0,
 136         .dev     = {
 137                 .platform_data  = &ixdp425_i2c_gpio_data,
 138         },
 139 };
 140
 141 static struct resource ixdp425_uart_resources[] = {
 142         {
 143                 .start          = IXP4XX_UART1_BASE_PHYS,
 144                 .end            = IXP4XX_UART1_BASE_PHYS + 0x0fff,
 145                 .flags          = IORESOURCE_MEM
 146         },
 147         {
 148                 .start          = IXP4XX_UART2_BASE_PHYS,
 149                 .end            = IXP4XX_UART2_BASE_PHYS + 0x0fff,
 150                 .flags          = IORESOURCE_MEM
 151         }
 152 };
 153
 154 static struct plat_serial8250_port ixdp425_uart_data[] = {
 155         {
 156                 .mapbase        = IXP4XX_UART1_BASE_PHYS,
 157                 .membase        = (char *)IXP4XX_UART1_BASE_VIRT + REG_OFFSET,
 158                 .irq            = IRQ_IXP4XX_UART1,
 159                 .flags          = UPF_BOOT_AUTOCONF | UPF_SKIP_TEST,
 160                 .iotype         = UPIO_MEM,
 161                 .regshift       = 2,
 162                 .uartclk        = IXP4XX_UART_XTAL,
 163         },
 164         {
 165                 .mapbase        = IXP4XX_UART2_BASE_PHYS,
 166                 .membase        = (char *)IXP4XX_UART2_BASE_VIRT + REG_OFFSET,
 167                 .irq            = IRQ_IXP4XX_UART2,
 168                 .flags          = UPF_BOOT_AUTOCONF | UPF_SKIP_TEST,
 169                 .iotype         = UPIO_MEM,
 170                 .regshift       = 2,
 171                 .uartclk        = IXP4XX_UART_XTAL,
 172         },
 173         { },
 174 };
 175
 176 static struct platform_device ixdp425_uart = {
 177         .name                   = "serial8250",
 178         .id                     = PLAT8250_DEV_PLATFORM,
 179         .dev.platform_data      = ixdp425_uart_data,
 180         .num_resources          = 2,
 181         .resource               = ixdp425_uart_resources
 182 };
 183
 184 /* Built-in 10/100 Ethernet MAC interfaces */
 185 static struct eth_plat_info ixdp425_plat_eth[] = {
 186         {
 187                 .phy            = 0,
 188                 .rxq            = 3,
 189                 .txreadyq       = 20,
 190         }, {
 191                 .phy            = 1,
 192                 .rxq            = 4,
 193                 .txreadyq       = 21,
 194         }
 195 };
 196
 197 static struct platform_device ixdp425_eth[] = {
 198         {
 199                 .name                   = "ixp4xx_eth",
 200                 .id                     = IXP4XX_ETH_NPEB,
 201                 .dev.platform_data      = ixdp425_plat_eth,
 202         }, {
 203                 .name                   = "ixp4xx_eth",
 204                 .id                     = IXP4XX_ETH_NPEC,
 205                 .dev.platform_data      = ixdp425_plat_eth + 1,
 206         }
 207 };
 208
 209 static struct platform_device *ixdp425_devices[] __initdata = {
 210         &ixdp425_i2c_gpio,
 211         &ixdp425_flash,
 212 #if defined(CONFIG_MTD_NAND_PLATFORM) || \
 213     defined(CONFIG_MTD_NAND_PLATFORM_MODULE)
 214         &ixdp425_flash_nand,
 215 #endif
 216         &ixdp425_uart,
 217         &ixdp425_eth[0],
 218         &ixdp425_eth[1],
 219 };
 220
 221 static void __init ixdp425_init(void)
 222 {
 223         ixp4xx_sys_init();
 224
 225         ixdp425_flash_resource.start = IXP4XX_EXP_BUS_BASE(0);
 226         ixdp425_flash_resource.end =
 227                 IXP4XX_EXP_BUS_BASE(0) + ixp4xx_exp_bus_size - 1;
 228
 229 #if defined(CONFIG_MTD_NAND_PLATFORM) || \
 230     defined(CONFIG_MTD_NAND_PLATFORM_MODULE)
 231         ixdp425_flash_nand_resource.start = IXP4XX_EXP_BUS_BASE(3),
 232         ixdp425_flash_nand_resource.end   = IXP4XX_EXP_BUS_BASE(3) + 0x10 - 1;
 233
 234         gpio_line_config(IXDP425_NAND_NCE_PIN, IXP4XX_GPIO_OUT);
 235
 236         /* Configure expansion bus for NAND Flash */
 237         *IXP4XX_EXP_CS3 = IXP4XX_EXP_BUS_CS_EN |
 238                           IXP4XX_EXP_BUS_STROBE_T(1) |  /* extend by 1 clock */
 239                           IXP4XX_EXP_BUS_CYCLES(0) |    /* Intel cycles */
 240                           IXP4XX_EXP_BUS_SIZE(0) |      /* 512bytes addr space*/
 241                           IXP4XX_EXP_BUS_WR_EN |
 242                           IXP4XX_EXP_BUS_BYTE_EN;       /* 8 bit data bus */
 243 #endif
 244
 245         if (cpu_is_ixp43x()) {
 246                 ixdp425_uart.num_resources = 1;
 247                 ixdp425_uart_data[1].flags = 0;
 248         }
 249
 250         platform_add_devices(ixdp425_devices, ARRAY_SIZE(ixdp425_devices));
 251 }
 252
 253 #ifdef CONFIG_ARCH_IXDP425
 254 MACHINE_START(IXDP425, "Intel IXDP425 Development Platform")
 255         /* Maintainer: MontaVista Software, Inc. */
 256         .map_io         = ixp4xx_map_io,
 257         .init_irq       = ixp4xx_init_irq,
 258         .timer          = &ixp4xx_timer,
 259         .boot_params    = 0x0100,
 260         .init_machine   = ixdp425_init,
 261 #if defined(CONFIG_PCI)
 262         .dma_zone_size  = SZ_64M,
 263 #endif
 264 MACHINE_END
 265 #endif
 266
 267 #ifdef CONFIG_MACH_IXDP465
 268 MACHINE_START(IXDP465, "Intel IXDP465 Development Platform")
 269         /* Maintainer: MontaVista Software, Inc. */
 270         .map_io         = ixp4xx_map_io,
 271         .init_irq       = ixp4xx_init_irq,
 272         .timer          = &ixp4xx_timer,
 273         .boot_params    = 0x0100,
 274         .init_machine   = ixdp425_init,
 275 #if defined(CONFIG_PCI)
 276         .dma_zone_size  = SZ_64M,
 277 #endif
 278 MACHINE_END
 279 #endif
 280
 281 #ifdef CONFIG_ARCH_PRPMC1100
 282 MACHINE_START(IXCDP1100, "Intel IXCDP1100 Development Platform")
 283         /* Maintainer: MontaVista Software, Inc. */
 284         .map_io         = ixp4xx_map_io,
 285         .init_irq       = ixp4xx_init_irq,
 286         .timer          = &ixp4xx_timer,
 287         .boot_params    = 0x0100,
 288         .init_machine   = ixdp425_init,
 289 #if defined(CONFIG_PCI)
 290         .dma_zone_size  = SZ_64M,
 291 #endif
 292 MACHINE_END
 293 #endif
 294
 295 #ifdef CONFIG_MACH_KIXRP435
 296 MACHINE_START(KIXRP435, "Intel KIXRP435 Reference Platform")
 297         /* Maintainer: MontaVista Software, Inc. */
 298         .map_io         = ixp4xx_map_io,
 299         .init_irq       = ixp4xx_init_irq,
 300         .timer          = &ixp4xx_timer,
 301         .boot_params    = 0x0100,
 302         .init_machine   = ixdp425_init,
 303 #if defined(CONFIG_PCI)
 304         .dma_zone_size  = SZ_64M,
 305 #endif
 306 MACHINE_END
 307 #endif