arch/arm/mach-at91/board-pcontrol-g20.c

   1 /*
   2  *  Copyright (C) 2010 Christian Glindkamp <christian.glindkamp@taskit.de>
   3  *                     taskit GmbH
   4  *
   5  * This program is free software; you can redistribute it and/or modify
   6  * it under the terms of the GNU General Public License as published by
   7  * the Free Software Foundation; either version 2 of the License, or
   8  * (at your option) any later version.
   9  *
  10  * This program is distributed in the hope that it will be useful,
  11  * but WITHOUT ANY WARRANTY; without even the implied warranty of
  12  * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
  13  * GNU General Public License for more details.
  14  *
  15  * You should have received a copy of the GNU General Public License
  16  * along with this program; if not, write to the Free Software
  17  * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA  02111-1307  USA
  18  */
  19 /*
  20  * copied and adjusted from board-stamp9g20.c
  21  * by Peter Gsellmann <pgsellmann@portner-elektronik.at>
  22  */
  23
  24 #include <linux/mm.h>
  25 #include <linux/platform_device.h>
  26 #include <linux/gpio.h>
  27 #include <linux/w1-gpio.h>
  28
  29 #include <asm/mach-types.h>
  30 #include <asm/mach/arch.h>
  31
  32 #include <mach/board.h>
  33 #include <mach/at91sam9_smc.h>
  34
  35 #include "sam9_smc.h"
  36 #include "generic.h"
  37
  38
  39 static void __init pcontrol_g20_map_io(void)
  40 {
  41         /* Initialize processor: 18.432 MHz crystal */
  42         at91sam9260_initialize(18432000);
  43
  44         /* DGBU on ttyS0. (Rx, Tx) only TTL -> JTAG connector X7 17,19 ) */
  45         at91_register_uart(0, 0, 0);
  46
  47         /* USART0 on ttyS1. (Rx, Tx, CTS, RTS) piggyback  A2 */
  48         at91_register_uart(AT91SAM9260_ID_US0, 1, ATMEL_UART_CTS
  49                                                 | ATMEL_UART_RTS);
  50
  51         /* USART1 on ttyS2. (Rx, Tx, CTS, RTS) isolated RS485  X5 */
  52         at91_register_uart(AT91SAM9260_ID_US1, 2, ATMEL_UART_CTS
  53                                                 | ATMEL_UART_RTS);
  54
  55         /* USART2 on ttyS3. (Rx, Tx)  9bit-Bus  Multidrop-mode  X4 */
  56         at91_register_uart(AT91SAM9260_ID_US4, 3, 0);
  57
  58         /* set serial console to ttyS0 (ie, DBGU) */
  59         at91_set_serial_console(0);
  60 }
  61
  62
  63 static void __init init_irq(void)
  64 {
  65         at91sam9260_init_interrupts(NULL);
  66 }
  67
  68
  69 /*
  70  * NAND flash 512MiB 1,8V 8-bit, sector size 128 KiB
  71  */
  72 static struct atmel_nand_data __initdata nand_data = {
  73         .ale            = 21,
  74         .cle            = 22,
  75         .rdy_pin        = AT91_PIN_PC13,
  76         .enable_pin     = AT91_PIN_PC14,
  77 };
  78
  79 /*
  80  * Bus timings; unit = 7.57ns
  81  */
  82 static struct sam9_smc_config __initdata nand_smc_config = {
  83         .ncs_read_setup         = 0,
  84         .nrd_setup              = 2,
  85         .ncs_write_setup        = 0,
  86         .nwe_setup              = 2,
  87
  88         .ncs_read_pulse         = 4,
  89         .nrd_pulse              = 4,
  90         .ncs_write_pulse        = 4,
  91         .nwe_pulse              = 4,
  92
  93         .read_cycle             = 7,
  94         .write_cycle            = 7,
  95
  96         .mode                   = AT91_SMC_READMODE | AT91_SMC_WRITEMODE
  97                         | AT91_SMC_EXNWMODE_DISABLE | AT91_SMC_DBW_8,
  98         .tdf_cycles             = 3,
  99 };
 100
 101 static struct sam9_smc_config __initdata pcontrol_smc_config[2] = { {
 102         .ncs_read_setup         = 16,
 103         .nrd_setup              = 18,
 104         .ncs_write_setup        = 16,
 105         .nwe_setup              = 18,
 106
 107         .ncs_read_pulse         = 63,
 108         .nrd_pulse              = 55,
 109         .ncs_write_pulse        = 63,
 110         .nwe_pulse              = 55,
 111
 112         .read_cycle             = 127,
 113         .write_cycle            = 127,
 114
 115         .mode                   = AT91_SMC_READMODE | AT91_SMC_WRITEMODE
 116                         | AT91_SMC_EXNWMODE_DISABLE | AT91_SMC_BAT_SELECT
 117                         | AT91_SMC_DBW_8 | AT91_SMC_PS_4
 118                         | AT91_SMC_TDFMODE,
 119         .tdf_cycles             = 3,
 120 }, {
 121         .ncs_read_setup         = 0,
 122         .nrd_setup              = 0,
 123         .ncs_write_setup        = 0,
 124         .nwe_setup              = 1,
 125
 126         .ncs_read_pulse         = 8,
 127         .nrd_pulse              = 8,
 128         .ncs_write_pulse        = 5,
 129         .nwe_pulse              = 4,
 130
 131         .read_cycle             = 8,
 132         .write_cycle            = 7,
 133
 134         .mode                   = AT91_SMC_READMODE | AT91_SMC_WRITEMODE
 135                         | AT91_SMC_EXNWMODE_DISABLE | AT91_SMC_BAT_SELECT
 136                         | AT91_SMC_DBW_16 | AT91_SMC_PS_8
 137                         | AT91_SMC_TDFMODE,
 138         .tdf_cycles             = 1,
 139 } };
 140
 141 static void __init add_device_nand(void)
 142 {
 143         /* configure chip-select 3 (NAND) */
 144         sam9_smc_configure(3, &nand_smc_config);
 145         at91_add_device_nand(&nand_data);
 146 }
 147
 148
 149 static void __init add_device_pcontrol(void)
 150 {
 151         /* configure chip-select 4 (IO compatible to 8051  X4 ) */
 152         sam9_smc_configure(4, &pcontrol_smc_config[0]);
 153         /* configure chip-select 7 (FerroRAM 256KiBx16bit MR2A16A  D4 ) */
 154         sam9_smc_configure(7, &pcontrol_smc_config[1]);
 155 }
 156
 157
 158 /*
 159  * MCI (SD/MMC)
 160  * det_pin, wp_pin and vcc_pin are not connected
 161  */
 162 #if defined(CONFIG_MMC_ATMELMCI) || defined(CONFIG_MMC_ATMELMCI_MODULE)
 163 static struct mci_platform_data __initdata mmc_data = {
 164         .slot[0] = {
 165                 .bus_width      = 4,
 166         },
 167 };
 168 #else
 169 static struct at91_mmc_data __initdata mmc_data = {
 170         .wire4          = 1,
 171 };
 172 #endif
 173
 174
 175 /*
 176  * USB Host port
 177  */
 178 static struct at91_usbh_data __initdata usbh_data = {
 179         .ports          = 2,
 180 };
 181
 182
 183 /*
 184  * USB Device port
 185  */
 186 static struct at91_udc_data __initdata pcontrol_g20_udc_data = {
 187         .vbus_pin       = AT91_PIN_PA22,        /* Detect +5V bus voltage */
 188         .pullup_pin     = AT91_PIN_PA4,         /* K-state, active low */
 189 };
 190
 191
 192 /*
 193  * MACB Ethernet device
 194  */
 195 static struct at91_eth_data __initdata macb_data = {
 196         .phy_irq_pin    = AT91_PIN_PA28,
 197         .is_rmii        = 1,
 198 };
 199
 200
 201 /*
 202  * I2C devices: eeprom and phy/switch
 203  */
 204 static struct i2c_board_info __initdata pcontrol_g20_i2c_devices[] = {
 205 {               /* D7  address width=2, 8KiB */
 206         I2C_BOARD_INFO("24c64", 0x50)
 207 }, {            /* D8  address width=1, 1 byte has 32 bits! */
 208         I2C_BOARD_INFO("lan9303", 0x0a)
 209 }, };
 210
 211
 212 /*
 213  * LEDs
 214  */
 215 static struct gpio_led pcontrol_g20_leds[] = {
 216         {
 217                 .name                   = "LED1",       /* red  H5 */
 218                 .gpio                   = AT91_PIN_PB18,
 219                 .active_low             = 1,
 220                 .default_trigger        = "none",       /* supervisor */
 221         }, {
 222                 .name                   = "LED2",       /* yellow  H7 */
 223                 .gpio                   = AT91_PIN_PB19,
 224                 .active_low             = 1,
 225                 .default_trigger        = "mmc0",       /* SD-card activity */
 226         }, {
 227                 .name                   = "LED3",       /* green  H2 */
 228                 .gpio                   = AT91_PIN_PB20,
 229                 .active_low             = 1,
 230                 .default_trigger        = "heartbeat",  /* blinky */
 231         }, {
 232                 .name                   = "LED4",       /* red  H3 */
 233                 .gpio                   = AT91_PIN_PC6,
 234                 .active_low             = 1,
 235                 .default_trigger        = "none",       /* connection lost */
 236         }, {
 237                 .name                   = "LED5",       /* yellow  H6 */
 238                 .gpio                   = AT91_PIN_PC7,
 239                 .active_low             = 1,
 240                 .default_trigger        = "none",       /* unsent data */
 241         }, {
 242                 .name                   = "LED6",       /* green  H1 */
 243                 .gpio                   = AT91_PIN_PC9,
 244                 .active_low             = 1,
 245                 .default_trigger        = "none",       /* snafu */
 246         }
 247 };
 248
 249
 250 /*
 251  * SPI devices
 252  */
 253 static struct spi_board_info pcontrol_g20_spi_devices[] = {
 254         {
 255                 .modalias       = "spidev",     /* HMI port  X4 */
 256                 .chip_select    = 1,
 257                 .max_speed_hz   = 50 * 1000 * 1000,
 258                 .bus_num        = 0,
 259         }, {
 260                 .modalias       = "spidev",     /* piggyback  A2 */
 261                 .chip_select    = 0,
 262                 .max_speed_hz   = 50 * 1000 * 1000,
 263                 .bus_num        = 1,
 264         },
 265 };
 266
 267
 268 /*
 269  * Dallas 1-Wire  DS2431
 270  */
 271 static struct w1_gpio_platform_data w1_gpio_pdata = {
 272         .pin            = AT91_PIN_PA29,
 273         .is_open_drain  = 1,
 274 };
 275
 276 static struct platform_device w1_device = {
 277         .name                   = "w1-gpio",
 278         .id                     = -1,
 279         .dev.platform_data      = &w1_gpio_pdata,
 280 };
 281
 282 static void add_wire1(void)
 283 {
 284         at91_set_GPIO_periph(w1_gpio_pdata.pin, 1);
 285         at91_set_multi_drive(w1_gpio_pdata.pin, 1);
 286         platform_device_register(&w1_device);
 287 }
 288
 289
 290 static void __init pcontrol_g20_board_init(void)
 291 {
 292         at91_add_device_serial();
 293         add_device_nand();
 294 #if defined(CONFIG_MMC_ATMELMCI) || defined(CONFIG_MMC_ATMELMCI_MODULE)
 295         at91_add_device_mci(0, &mmc_data);
 296 #else
 297         at91_add_device_mmc(0, &mmc_data);
 298 #endif
 299         at91_add_device_usbh(&usbh_data);
 300         at91_add_device_eth(&macb_data);
 301         at91_add_device_i2c(pcontrol_g20_i2c_devices,
 302                 ARRAY_SIZE(pcontrol_g20_i2c_devices));
 303         add_wire1();
 304         add_device_pcontrol();
 305         at91_add_device_spi(pcontrol_g20_spi_devices,
 306                 ARRAY_SIZE(pcontrol_g20_spi_devices));
 307         at91_add_device_udc(&pcontrol_g20_udc_data);
 308         at91_gpio_leds(pcontrol_g20_leds,
 309                 ARRAY_SIZE(pcontrol_g20_leds));
 310         /* piggyback  A2 */
 311         at91_set_gpio_output(AT91_PIN_PB31, 1);
 312 }
 313
 314
 315 MACHINE_START(PCONTROL_G20, "PControl G20")
 316         /* Maintainer: pgsellmann@portner-elektronik.at */
 317         .boot_params    = AT91_SDRAM_BASE + 0x100,
 318         .timer          = &at91sam926x_timer,
 319         .map_io         = pcontrol_g20_map_io,
 320         .init_irq       = init_irq,
 321         .init_machine   = pcontrol_g20_board_init,
 322 MACHINE_END