4 The following is a consolidated list of the kernel parameters as implemented
5 (mostly) by the __setup() macro and sorted into English Dictionary order
6 (defined as ignoring all punctuation and sorting digits before letters in a
7 case insensitive manner), and with descriptions where known.
9 Module parameters for loadable modules are specified only as the
10 parameter name with optional '=' and value as appropriate, such as:
12 modprobe usbcore blinkenlights=1
14 Module parameters for modules that are built into the kernel image
15 are specified on the kernel command line with the module name plus
16 '.' plus parameter name, with '=' and value if appropriate, such as:
18 usbcore.blinkenlights=1
20 Hyphens (dashes) and underscores are equivalent in parameter names, so
21 log_buf_len=1M print-fatal-signals=1
22 can also be entered as
23 log-buf-len=1M print_fatal_signals=1
26 This document may not be entirely up to date and comprehensive. The command
27 "modinfo -p ${modulename}" shows a current list of all parameters of a loadable
28 module. Loadable modules, after being loaded into the running kernel, also
29 reveal their parameters in /sys/module/${modulename}/parameters/. Some of these
30 parameters may be changed at runtime by the command
31 "echo -n ${value} > /sys/module/${modulename}/parameters/${parm}".
33 The parameters listed below are only valid if certain kernel build options were
34 enabled and if respective hardware is present. The text in square brackets at
35 the beginning of each description states the restrictions within which a
36 parameter is applicable:
38 ACPI ACPI support is enabled.
39 AGP AGP (Accelerated Graphics Port) is enabled.
40 ALSA ALSA sound support is enabled.
41 APIC APIC support is enabled.
42 APM Advanced Power Management support is enabled.
43 AVR32 AVR32 architecture is enabled.
44 AX25 Appropriate AX.25 support is enabled.
45 BLACKFIN Blackfin architecture is enabled.
46 EDD BIOS Enhanced Disk Drive Services (EDD) is enabled
47 EFI EFI Partitioning (GPT) is enabled
48 EIDE EIDE/ATAPI support is enabled.
49 DRM Direct Rendering Management support is enabled.
50 DYNAMIC_DEBUG Build in debug messages and enable them at runtime
51 FB The frame buffer device is enabled.
52 GCOV GCOV profiling is enabled.
53 HW Appropriate hardware is enabled.
54 IA-64 IA-64 architecture is enabled.
55 IMA Integrity measurement architecture is enabled.
56 IOSCHED More than one I/O scheduler is enabled.
57 IP_PNP IP DHCP, BOOTP, or RARP is enabled.
58 IPV6 IPv6 support is enabled.
59 ISAPNP ISA PnP code is enabled.
60 ISDN Appropriate ISDN support is enabled.
61 JOY Appropriate joystick support is enabled.
62 KGDB Kernel debugger support is enabled.
63 KVM Kernel Virtual Machine support is enabled.
64 LIBATA Libata driver is enabled
65 LP Printer support is enabled.
66 LOOP Loopback device support is enabled.
67 M68k M68k architecture is enabled.
68 These options have more detailed description inside of
69 Documentation/m68k/kernel-options.txt.
70 MCA MCA bus support is enabled.
71 MDA MDA console support is enabled.
72 MOUSE Appropriate mouse support is enabled.
73 MSI Message Signaled Interrupts (PCI).
74 MTD MTD (Memory Technology Device) support is enabled.
75 NET Appropriate network support is enabled.
76 NUMA NUMA support is enabled.
77 NFS Appropriate NFS support is enabled.
78 OSS OSS sound support is enabled.
79 PV_OPS A paravirtualized kernel is enabled.
80 PARIDE The ParIDE (parallel port IDE) subsystem is enabled.
81 PARISC The PA-RISC architecture is enabled.
82 PCI PCI bus support is enabled.
83 PCIE PCI Express support is enabled.
84 PCMCIA The PCMCIA subsystem is enabled.
85 PNP Plug & Play support is enabled.
86 PPC PowerPC architecture is enabled.
87 PPT Parallel port support is enabled.
88 PS2 Appropriate PS/2 support is enabled.
89 RAM RAM disk support is enabled.
90 S390 S390 architecture is enabled.
91 SCSI Appropriate SCSI support is enabled.
92 A lot of drivers have their options described inside
93 the Documentation/scsi/ sub-directory.
94 SECURITY Different security models are enabled.
95 SELINUX SELinux support is enabled.
96 APPARMOR AppArmor support is enabled.
97 SERIAL Serial support is enabled.
98 SH SuperH architecture is enabled.
99 SMP The kernel is an SMP kernel.
100 SPARC Sparc architecture is enabled.
101 SWSUSP Software suspend (hibernation) is enabled.
102 SUSPEND System suspend states are enabled.
103 FTRACE Function tracing enabled.
104 TPM TPM drivers are enabled.
105 TS Appropriate touchscreen support is enabled.
106 UMS USB Mass Storage support is enabled.
107 USB USB support is enabled.
108 USBHID USB Human Interface Device support is enabled.
109 V4L Video For Linux support is enabled.
110 VGA The VGA console has been enabled.
111 VT Virtual terminal support is enabled.
112 WDT Watchdog support is enabled.
113 XT IBM PC/XT MFM hard disk support is enabled.
114 X86-32 X86-32, aka i386 architecture is enabled.
115 X86-64 X86-64 architecture is enabled.
116 More X86-64 boot options can be found in
117 Documentation/x86/x86_64/boot-options.txt .
118 X86 Either 32bit or 64bit x86 (same as X86-32+X86-64)
119 XEN Xen support is enabled
121 In addition, the following text indicates that the option:
123 BUGS= Relates to possible processor bugs on the said processor.
124 KNL Is a kernel start-up parameter.
125 BOOT Is a boot loader parameter.
127 Parameters denoted with BOOT are actually interpreted by the boot
128 loader, and have no meaning to the kernel directly.
129 Do not modify the syntax of boot loader parameters without extreme
130 need or coordination with <Documentation/x86/boot.txt>.
132 There are also arch-specific kernel-parameters not documented here.
133 See for example <Documentation/x86/x86_64/boot-options.txt>.
135 Note that ALL kernel parameters listed below are CASE SENSITIVE, and that
136 a trailing = on the name of any parameter states that that parameter will
137 be entered as an environment variable, whereas its absence indicates that
138 it will appear as a kernel argument readable via /proc/cmdline by programs
139 running once the system is up.
141 The number of kernel parameters is not limited, but the length of the
142 complete command line (parameters including spaces etc.) is limited to
143 a fixed number of characters. This limit depends on the architecture
144 and is between 256 and 4096 characters. It is defined in the file
145 ./include/asm/setup.h as COMMAND_LINE_SIZE.
149 Advanced Configuration and Power Interface
150 Format: { force | off | strict | noirq | rsdt }
151 force -- enable ACPI if default was off
152 off -- disable ACPI if default was on
153 noirq -- do not use ACPI for IRQ routing
154 strict -- Be less tolerant of platforms that are not
155 strictly ACPI specification compliant.
156 rsdt -- prefer RSDT over (default) XSDT
157 copy_dsdt -- copy DSDT to memory
159 See also Documentation/power/pm.txt, pci=noacpi
161 acpi_apic_instance= [ACPI, IOAPIC]
163 2: use 2nd APIC table, if available
164 1,0: use 1st APIC table
167 acpi_backlight= [HW,ACPI]
168 acpi_backlight=vendor
170 If set to vendor, prefer vendor specific driver
171 (e.g. thinkpad_acpi, sony_acpi, etc.) instead
172 of the ACPI video.ko driver.
174 acpi.debug_layer= [HW,ACPI,ACPI_DEBUG]
175 acpi.debug_level= [HW,ACPI,ACPI_DEBUG]
177 CONFIG_ACPI_DEBUG must be enabled to produce any ACPI
178 debug output. Bits in debug_layer correspond to a
179 _COMPONENT in an ACPI source file, e.g.,
180 #define _COMPONENT ACPI_PCI_COMPONENT
181 Bits in debug_level correspond to a level in
182 ACPI_DEBUG_PRINT statements, e.g.,
183 ACPI_DEBUG_PRINT((ACPI_DB_INFO, ...
184 The debug_level mask defaults to "info". See
185 Documentation/acpi/debug.txt for more information about
186 debug layers and levels.
188 Enable processor driver info messages:
189 acpi.debug_layer=0x20000000
190 Enable PCI/PCI interrupt routing info messages:
191 acpi.debug_layer=0x400000
192 Enable AML "Debug" output, i.e., stores to the Debug
193 object while interpreting AML:
194 acpi.debug_layer=0xffffffff acpi.debug_level=0x2
195 Enable all messages related to ACPI hardware:
196 acpi.debug_layer=0x2 acpi.debug_level=0xffffffff
198 Some values produce so much output that the system is
199 unusable. The "log_buf_len" parameter may be useful
200 if you need to capture more output.
202 acpi_display_output= [HW,ACPI]
203 acpi_display_output=vendor
204 acpi_display_output=video
207 acpi_irq_balance [HW,ACPI]
208 ACPI will balance active IRQs
211 acpi_irq_nobalance [HW,ACPI]
212 ACPI will not move active IRQs (default)
215 acpi_irq_isa= [HW,ACPI] If irq_balance, mark listed IRQs used by ISA
216 Format: <irq>,<irq>...
218 acpi_irq_pci= [HW,ACPI] If irq_balance, clear listed IRQs for
220 Format: <irq>,<irq>...
222 acpi_no_auto_ssdt [HW,ACPI] Disable automatic loading of SSDT
224 acpi_os_name= [HW,ACPI] Tell ACPI BIOS the name of the OS
225 Format: To spoof as Windows 98: ="Microsoft Windows"
227 acpi_osi= [HW,ACPI] Modify list of supported OS interface strings
228 acpi_osi="string1" # add string1 -- only one string
229 acpi_osi="!string2" # remove built-in string2
230 acpi_osi= # disable all strings
233 Override the pmtimer bug detection: force the kernel
234 to assume that this machine's pmtimer latches its value
235 and always returns good values.
237 acpi_sci= [HW,ACPI] ACPI System Control Interrupt trigger mode
238 Format: { level | edge | high | low }
240 acpi_serialize [HW,ACPI] force serialization of AML methods
242 acpi_skip_timer_override [HW,ACPI]
243 Recognize and ignore IRQ0/pin2 Interrupt Override.
244 For broken nForce2 BIOS resulting in XT-PIC timer.
246 acpi_sleep= [HW,ACPI] Sleep options
247 Format: { s3_bios, s3_mode, s3_beep, s4_nohwsig,
248 old_ordering, s4_nonvs, sci_force_enable }
249 See Documentation/power/video.txt for information on
251 s3_beep is for debugging; it makes the PC's speaker beep
252 as soon as the kernel's real-mode entry point is called.
253 s4_nohwsig prevents ACPI hardware signature from being
254 used during resume from hibernation.
255 old_ordering causes the ACPI 1.0 ordering of the _PTS
256 control method, with respect to putting devices into
257 low power states, to be enforced (the ACPI 2.0 ordering
258 of _PTS is used by default).
259 nonvs prevents the kernel from saving/restoring the
260 ACPI NVS memory during suspend/hibernation and resume.
261 sci_force_enable causes the kernel to set SCI_EN directly
262 on resume from S1/S3 (which is against the ACPI spec,
263 but some broken systems don't work without it).
265 acpi_use_timer_override [HW,ACPI]
266 Use timer override. For some broken Nvidia NF5 boards
267 that require a timer override, but don't have HPET
269 acpi_enforce_resources= [ACPI]
270 { strict | lax | no }
271 Check for resource conflicts between native drivers
272 and ACPI OperationRegions (SystemIO and SystemMemory
273 only). IO ports and memory declared in ACPI might be
274 used by the ACPI subsystem in arbitrary AML code and
275 can interfere with legacy drivers.
276 strict (default): access to resources claimed by ACPI
277 is denied; legacy drivers trying to access reserved
278 resources will fail to bind to device using them.
279 lax: access to resources claimed by ACPI is allowed;
280 legacy drivers trying to access reserved resources
281 will bind successfully but a warning message is logged.
282 no: ACPI OperationRegions are not marked as reserved,
283 no further checks are performed.
285 add_efi_memmap [EFI; X86] Include EFI memory map in
286 kernel's map of available physical RAM.
289 { off | try_unsupported }
290 off: disable AGP support
291 try_unsupported: try to drive unsupported chipsets
292 (may crash computer or cause data corruption)
295 See Documentation/sound/alsa/alsa-parameters.txt
298 Allow the default userspace alignment fault handler
299 behaviour to be specified. Bit 0 enables warnings,
300 bit 1 enables fixups, and bit 2 sends a segfault.
302 amd_iommu= [HW,X86-84]
303 Pass parameters to the AMD IOMMU driver in the system.
305 fullflush - enable flushing of IO/TLB entries when
306 they are unmapped. Otherwise they are
307 flushed before they will be reused, which
309 off - do not initialize any AMD IOMMU found in
312 amijoy.map= [HW,JOY] Amiga joystick support
313 Map of devices attached to JOY0DAT and JOY1DAT
315 See also Documentation/kernel/input/joystick.txt
317 analog.map= [HW,JOY] Analog joystick and gamepad support
318 Specifies type or capabilities of an analog joystick
319 connected to one of 16 gameports
320 Format: <type1>,<type2>,..<type16>
323 Power management functions (SPARCstation-4/5 + deriv.)
325 Disable APC CPU standby support. SPARCstation-Fox does
326 not play well with APC CPU idle - disable it if you have
327 APC and your system crashes randomly.
329 apic= [APIC,X86-32] Advanced Programmable Interrupt Controller
330 Change the output verbosity whilst booting
331 Format: { quiet (default) | verbose | debug }
332 Change the amount of debugging information output
333 when initialising the APIC and IO-APIC components.
336 See Documentation/networking/ipv6.txt.
338 show_lapic= [APIC,X86] Advanced Programmable Interrupt Controller
339 Limit apic dumping. The parameter defines the maximal
340 number of local apics being dumped. Also it is possible
341 to set it to "all" by meaning -- no limit here.
342 Format: { 1 (default) | 2 | ... | all }.
343 The parameter valid if only apic=debug or
344 apic=verbose is specified.
345 Example: apic=debug show_lapic=all
347 apm= [APM] Advanced Power Management
348 See header of arch/x86/kernel/apm_32.c.
350 arcrimi= [HW,NET] ARCnet - "RIM I" (entirely mem-mapped) cards
351 Format: <io>,<irq>,<nodeID>
355 atarimouse= [HW,MOUSE] Atari Mouse
357 atkbd.extra= [HW] Enable extra LEDs and keys on IBM RapidAccess,
358 EzKey and similar keyboards
360 atkbd.reset= [HW] Reset keyboard during initialization
362 atkbd.set= [HW] Select keyboard code set
363 Format: <int> (2 = AT (default), 3 = PS/2)
365 atkbd.scroll= [HW] Enable scroll wheel on MS Office and similar
368 atkbd.softraw= [HW] Choose between synthetic and real raw mode
369 Format: <bool> (0 = real, 1 = synthetic (default))
371 atkbd.softrepeat= [HW]
372 Use software keyboard repeat
376 baycom_epp= [HW,AX25]
379 baycom_par= [HW,AX25] BayCom Parallel Port AX.25 Modem
381 See header of drivers/net/hamradio/baycom_par.c.
383 baycom_ser_fdx= [HW,AX25]
384 BayCom Serial Port AX.25 Modem (Full Duplex Mode)
385 Format: <io>,<irq>,<mode>[,<baud>]
386 See header of drivers/net/hamradio/baycom_ser_fdx.c.
388 baycom_ser_hdx= [HW,AX25]
389 BayCom Serial Port AX.25 Modem (Half Duplex Mode)
390 Format: <io>,<irq>,<mode>
391 See header of drivers/net/hamradio/baycom_ser_hdx.c.
393 boot_delay= Milliseconds to delay each printk during boot.
394 Values larger than 10 seconds (10000) are changed to
398 bootmem_debug [KNL] Enable bootmem allocator debug messages.
400 bttv.card= [HW,V4L] bttv (bt848 + bt878 based grabber cards)
401 bttv.radio= Most important insmod options are available as
403 bttv.pll= See Documentation/video4linux/bttv/Insmod-options
404 bttv.tuner= and Documentation/video4linux/bttv/CARDLIST
406 c101= [NET] Moxa C101 synchronous serial card
408 cachesize= [BUGS=X86-32] Override level 2 CPU cache size detection.
409 Sometimes CPU hardware bugs make them report the cache
410 size incorrectly. The kernel will attempt work arounds
411 to fix known problems, but for some CPUs it is not
412 possible to determine what the correct size should be.
413 This option provides an override for these situations.
416 [SECURITY] Disable capabilities. This would normally
417 be used only if an alternative security model is to be
418 configured. Potentially dangerous and should only be
419 used if you are entirely sure of the consequences.
421 ccw_timeout_log [S390]
422 See Documentation/s390/CommonIO for details.
424 cgroup_disable= [KNL] Disable a particular controller
425 Format: {name of the controller(s) to disable}
426 {Currently supported controllers - "memory"}
428 checkreqprot [SELINUX] Set initial checkreqprot flag value.
429 Format: { "0" | "1" }
430 See security/selinux/Kconfig help text.
431 0 -- check protection applied by kernel (includes
432 any implied execute protection).
433 1 -- check protection requested by application.
434 Default value is set via a kernel config option.
435 Value can be changed at runtime via
436 /selinux/checkreqprot.
439 See Documentation/s390/CommonIO for details.
441 clock= [BUGS=X86-32, HW] gettimeofday clocksource override.
443 Forces specified clocksource (if available) to be used
444 when calculating gettimeofday(). If specified
445 clocksource is not available, it defaults to PIT.
446 Format: { pit | tsc | cyclone | pmtmr }
448 clocksource= Override the default clocksource
450 Override the default clocksource and use the clocksource
451 with the name specified.
452 Some clocksource names to choose from, depending on
454 [all] jiffies (this is the base, fallback clocksource)
456 [ARM] imx_timer1,OSTS,netx_timer,mpu_timer2,
457 pxa_timer,timer3,32k_counter,timer0_1
459 [X86-32] pit,hpet,tsc,vmi-timer;
460 scx200_hrt on Geode; cyclone on IBM x440
468 clearcpuid=BITNUM [X86]
469 Disable CPUID feature X for the kernel. See
470 arch/x86/include/asm/cpufeature.h for the valid bit
471 numbers. Note the Linux specific bits are not necessarily
472 stable over kernel options, but the vendor specific
474 Also note that user programs calling CPUID directly
475 or using the feature without checking anything
476 will still see it. This just prevents it from
477 being used by the kernel or shown in /proc/cpuinfo.
478 Also note the kernel might malfunction if you disable
481 cmo_free_hint= [PPC] Format: { yes | no }
482 Specify whether pages are marked as being inactive
483 when they are freed. This is used in CMO environments
484 to determine OS memory pressure for page stealing by
488 code_bytes [X86] How many bytes of object code to print
493 com20020= [HW,NET] ARCnet - COM20020 chipset
495 <io>[,<irq>[,<nodeID>[,<backplane>[,<ckp>[,<timeout>]]]]]
497 com90io= [HW,NET] ARCnet - COM90xx chipset (IO-mapped buffers)
501 ARCnet - COM90xx chipset (memory-mapped buffers)
502 Format: <io>[,<irq>[,<memstart>]]
504 condev= [HW,S390] console device
507 console= [KNL] Output console device and options.
509 tty<n> Use the virtual console device <n>.
513 Use the specified serial port. The options are of
514 the form "bbbbpnf", where "bbbb" is the baud rate,
515 "p" is parity ("n", "o", or "e"), "n" is number of
516 bits, and "f" is flow control ("r" for RTS or
517 omit it). Default is "9600n8".
519 See Documentation/serial-console.txt for more
521 Documentation/networking/netconsole.txt for an
524 uart[8250],io,<addr>[,options]
525 uart[8250],mmio,<addr>[,options]
526 Start an early, polled-mode console on the 8250/16550
527 UART at the specified I/O port or MMIO address,
528 switching to the matching ttyS device later. The
529 options are the same as for ttyS, above.
531 If the device connected to the port is not a TTY but a braille
532 device, prepend "brl," before the device type, for instance
534 For now, only VisioBraille is supported.
536 consoleblank= [KNL] The console blank (screen saver) timeout in
537 seconds. Defaults to 10*60 = 10mins. A value of 0
538 disables the blank timer.
541 [KNL] Change the default value for
542 /proc/<pid>/coredump_filter.
543 See also Documentation/filesystems/proc.txt.
545 cpcihp_generic= [HW,PCI] Generic port I/O CompactPCI driver
547 <first_slot>,<last_slot>,<port>,<enum_bit>[,<debug>]
549 crashkernel=nn[KMG]@ss[KMG]
550 [KNL] Reserve a chunk of physical memory to
551 hold a kernel to switch to with kexec on panic.
553 crashkernel=range1:size1[,range2:size2,...][@offset]
554 [KNL] Same as above, but depends on the memory
555 in the running system. The syntax of range is
556 start-[end] where start and end are both
557 a memory unit (amount[KMG]). See also
558 Documentation/kdump/kdump.txt for a example.
563 cs89x0_media= [HW,NET]
564 Format: { rj45 | aui | bnc }
567 See header of drivers/s390/block/dasd_devmap.c.
569 db9.dev[2|3]= [HW,JOY] Multisystem joystick support via parallel port
570 (one device per port)
571 Format: <port#>,<type>
572 See also Documentation/input/joystick-parport.txt
574 ddebug_query= [KNL,DYNAMIC_DEBUG] Enable debug messages at early boot
575 time. See Documentation/dynamic-debug-howto.txt for
578 debug [KNL] Enable kernel debugging (events log level).
581 [KNL] verbose self-tests
583 Print debugging info while doing the locking API
585 We default to 0 (no extra messages), setting it to
586 1 will print _a lot_ more information - normally
587 only useful to kernel developers.
589 debug_objects [KNL] Enable object debugging
592 [KNL] Disable object debugging
594 debugpat [X86] Enable PAT debugging
596 decnet.addr= [HW,NET]
597 Format: <area>[,<node>]
598 See also Documentation/networking/decnet.txt.
601 [same as hugepagesz=] The size of the default
602 HugeTLB page size. This is the size represented by
603 the legacy /proc/ hugepages APIs, used for SHM, and
604 default size when mounting hugetlbfs filesystems.
605 Defaults to the default architecture's huge page size
609 Set number of hash buckets for dentry cache.
612 IO parameters + enable/disable command.
614 digiepca= [HW,SERIAL]
615 See drivers/char/README.epca and
616 Documentation/serial/digiepca.txt.
619 See Documentation/networking/ipv6.txt.
622 See Documentation/networking/ipv6.txt.
624 disable_mtrr_cleanup [X86]
625 The kernel tries to adjust MTRR layout from continuous
626 to discrete, to make X server driver able to add WB
627 entry later. This parameter disables that.
629 disable_mtrr_trim [X86, Intel and AMD only]
630 By default the kernel will trim any uncacheable
631 memory out of your available memory pool based on
632 MTRR settings. This parameter disables that behavior,
633 possibly causing your machine to run very slowly.
635 disable_timer_pin_1 [X86]
636 Disable PIN 1 of APIC timer
637 Can be useful to work around chipset bugs.
639 dma_debug=off If the kernel is compiled with DMA_API_DEBUG support,
640 this option disables the debugging code at boot.
642 dma_debug_entries=<number>
643 This option allows to tune the number of preallocated
644 entries for DMA-API debugging code. One entry is
645 required per DMA-API allocation. Use this if the
646 DMA-API debugging code disables itself because the
647 architectural default is too low.
649 dma_debug_driver=<driver_name>
650 With this option the DMA-API debugging driver
651 filter feature can be enabled at boot time. Just
652 pass the driver to filter for as the parameter.
653 The filter can be disabled or changed to another
654 driver later using sysfs.
658 dynamic_printk Enables pr_debug()/dev_dbg() calls if
659 CONFIG_DYNAMIC_PRINTK_DEBUG has been enabled.
660 These can also be switched on/off via
661 <debugfs>/dynamic_printk/modules
663 earlycon= [KNL] Output early console device and options.
664 uart[8250],io,<addr>[,options]
665 uart[8250],mmio,<addr>[,options]
666 uart[8250],mmio32,<addr>[,options]
667 Start an early, polled-mode console on the 8250/16550
668 UART at the specified I/O port or MMIO address.
669 MMIO inter-register address stride is either 8bit (mmio)
671 The options are the same as for ttyS, above.
673 earlyprintk= [X86,SH,BLACKFIN]
675 earlyprintk=serial[,ttySn[,baudrate]]
676 earlyprintk=ttySn[,baudrate]
677 earlyprintk=dbgp[debugController#]
679 Append ",keep" to not disable it when the real console
682 Only vga or serial or usb debug port at a time.
684 Currently only ttyS0 and ttyS1 are supported.
686 Interaction with the standard serial driver is not
689 The VGA output is eventually overwritten by the real
692 ekgdboc= [X86,KGDB] Allow early kernel console debugging
695 This is desgined to be used in conjunction with
696 the boot argument: earlyprintk=vga
699 Format: {"off" | "on" | "skip[mbr]"}
701 eisa_irq_edge= [PARISC,HW]
702 See header of drivers/parisc/eisa.c.
705 See comment before function elanfreq_setup() in
706 arch/x86/kernel/cpu/cpufreq/elanfreq.c.
709 Format: {"anticipatory" | "cfq" | "deadline" | "noop"}
710 See Documentation/block/as-iosched.txt and
711 Documentation/block/deadline-iosched.txt for details.
713 elfcorehdr= [IA64,PPC,SH,X86]
714 Specifies physical address of start of kernel core
715 image elf header. Generally kexec loader will
716 pass this option to capture kernel.
717 See Documentation/kdump/kdump.txt for details.
719 enable_mtrr_cleanup [X86]
720 The kernel tries to adjust MTRR layout from continuous
721 to discrete, to make X server driver able to add WB
722 entry later. This parameter enables that.
724 enable_timer_pin_1 [X86]
725 Enable PIN 1 of APIC timer
726 Can be useful to work around chipset bugs
727 (in particular on some ATI chipsets).
728 The kernel tries to set a reasonable default.
730 enforcing [SELINUX] Set initial enforcing status.
732 See security/selinux/Kconfig help text.
733 0 -- permissive (log only, no denials).
734 1 -- enforcing (deny and log).
736 Value can be changed at runtime via /selinux/enforce.
739 Disable Error Record Serialization Table (ERST)
742 ether= [HW,NET] Ethernet cards parameters
743 This option is obsoleted by the "netdev=" option, which
744 has equivalent usage. See its documentation for details.
748 fail_make_request=[KNL]
749 General fault injection mechanism.
750 Format: <interval>,<probability>,<space>,<times>
751 See also /Documentation/fault-injection/.
754 See Documentation/blockdev/floppy.txt.
756 force_pal_cache_flush
757 [IA-64] Avoid check_sal_cache_flush which may hang on
758 buggy SAL_CACHE_FLUSH implementations. Using this
759 parameter will force ia64_sal_cache_flush to call
760 ia64_pal_cache_flush instead of SAL_CACHE_FLUSH.
763 [FTRACE] will set and start the specified tracer
764 as early as possible in order to facilitate early
767 ftrace_dump_on_oops[=orig_cpu]
768 [FTRACE] will dump the trace buffers on oops.
769 If no parameter is passed, ftrace will dump
770 buffers of all CPUs, but if you pass orig_cpu, it will
771 dump only the buffer of the CPU that triggered the
774 ftrace_filter=[function-list]
775 [FTRACE] Limit the functions traced by the function
776 tracer at boot up. function-list is a comma separated
777 list of functions. This list can be changed at run
778 time by the set_ftrace_filter file in the debugfs
781 ftrace_notrace=[function-list]
782 [FTRACE] Do not trace the functions specified in
783 function-list. This list can be changed at run time
784 by the set_ftrace_notrace file in the debugfs
787 ftrace_graph_filter=[function-list]
788 [FTRACE] Limit the top level callers functions traced
789 by the function graph tracer at boot up.
790 function-list is a comma separated list of functions
791 that can be changed at run time by the
792 set_graph_function file in the debugfs tracing directory.
795 [HW,JOY] Multisystem joystick and NES/SNES/PSX pad
796 support via parallel port (up to 5 devices per port)
797 Format: <port#>,<pad1>,<pad2>,<pad3>,<pad4>,<pad5>
798 See also Documentation/input/joystick-parport.txt
802 gart_fix_e820= [X86_64] disable the fix e820 for K8 GART
806 gcov_persist= [GCOV] When non-zero (default), profiling data for
807 kernel modules is saved and remains accessible via
808 debugfs, even when the module is unloaded/reloaded.
809 When zero, profiling data is discarded and associated
810 debugfs files are removed at module unload time.
812 gpt [EFI] Forces disk with valid GPT signature but
813 invalid Protective MBR to be treated as GPT.
815 hashdist= [KNL,NUMA] Large hashes allocated during boot
816 are distributed across NUMA nodes. Defaults on
817 for 64bit NUMA, off otherwise.
818 Format: 0 | 1 (for off | on)
820 hcl= [IA-64] SGI's Hardware Graph compatibility layer
822 hd= [EIDE] (E)IDE hard drive subsystem geometry
823 Format: <cyl>,<head>,<sect>
826 Disable Hardware Error Source Table (HEST) support;
827 corresponding firmware-first mode error processing
828 logic will be disabled.
830 highmem=nn[KMG] [KNL,BOOT] forces the highmem zone to have an exact
831 size of <nn>. This works even on boxes that have no
832 highmem otherwise. This also works to reduce highmem
833 size on bigger boxes.
835 highres= [KNL] Enable/disable high resolution timer mode.
836 Valid parameters: "on", "off"
840 See Documentation/isdn/README.HiSax.
844 hpet= [X86-32,HPET] option to control HPET usage
845 Format: { enable (default) | disable | force |
847 disable: disable HPET and use PIT instead
848 force: allow force enabled of undocumented chips (ICH4,
850 verbose: show contents of HPET registers during setup
852 hugepages= [HW,X86-32,IA-64] HugeTLB pages to allocate at boot.
853 hugepagesz= [HW,IA-64,PPC,X86-64] The size of the HugeTLB pages.
854 On x86-64 and powerpc, this option can be specified
855 multiple times interleaved with hugepages= to reserve
856 huge pages of different sizes. Valid pages sizes on
857 x86-64 are 2M (when the CPU supports "pse") and 1G
858 (when the CPU supports the "pdpe1gb" cpuinfo flag)
859 Note that 1GB pages can only be allocated at boot time
860 using hugepages= and not freed afterwards.
862 hvc_iucv= [S390] Number of z/VM IUCV hypervisor console (HVC)
863 terminal devices. Valid values: 0..8
864 hvc_iucv_allow= [S390] Comma-separated list of z/VM user IDs.
865 If specified, z/VM IUCV HVC accepts connections
866 from listed z/VM user IDs only.
868 i2c_bus= [HW] Override the default board specific I2C bus speed
869 or register an additional I2C bus that is not
870 registered from board initialization code.
874 i8042.debug [HW] Toggle i8042 debug mode
875 i8042.direct [HW] Put keyboard port into non-translated mode
876 i8042.dumbkbd [HW] Pretend that controller can only read data from
877 keyboard and cannot control its state
878 (Don't attempt to blink the leds)
879 i8042.noaux [HW] Don't check for auxiliary (== mouse) port
880 i8042.nokbd [HW] Don't check/create keyboard port
881 i8042.noloop [HW] Disable the AUX Loopback command while probing
883 i8042.nomux [HW] Don't check presence of an active multiplexing
885 i8042.nopnp [HW] Don't use ACPIPnP / PnPBIOS to discover KBD/AUX
887 i8042.reset [HW] Reset the controller during init and cleanup
888 i8042.unlock [HW] Unlock (ignore) the keylock
892 i8k.ignore_dmi [HW] Continue probing hardware even if DMI data
893 indicates that the driver is running on unsupported
895 i8k.force [HW] Activate i8k driver even if SMM BIOS signature
896 does not match list of supported models.
898 [HW] Report power status in /proc/i8k
899 (disabled by default)
900 i8k.restricted [HW] Allow controlling fans only if SYS_ADMIN
904 Format: <io>[,<membase>[,<icn_id>[,<icn_id2>]]]
906 ide-core.nodma= [HW] (E)IDE subsystem
907 Format: =0.0 to prevent dma on hda, =0.1 hdb =1.0 hdc
908 .vlb_clock .pci_clock .noflush .nohpa .noprobe .nowerr
909 .cdrom .chs .ignore_cable are additional options
910 See Documentation/ide/ide.txt.
912 ide-pci-generic.all-generic-ide [HW] (E)IDE subsystem
913 Claim all unknown PCI IDE storage controllers.
916 Format: idle=poll, idle=mwait, idle=halt, idle=nomwait
917 Poll forces a polling idle loop that can slightly
918 improve the performance of waking up a idle CPU, but
919 will use a lot of power and make the system run hot.
921 idle=mwait: On systems which support MONITOR/MWAIT but
922 the kernel chose to not use it because it doesn't save
923 as much power as a normal idle loop, use the
924 MONITOR/MWAIT idle loop anyways. Performance should be
925 the same as idle=poll.
926 idle=halt: Halt is forced to be used for CPU idle.
927 In such case C2/C3 won't be used again.
928 idle=nomwait: Disable mwait for CPU C-states
930 ignore_loglevel [KNL]
931 Ignore loglevel setting - this will print /all/
932 kernel messages to the console. Useful for debugging.
935 Set number of hash buckets for inode cache.
938 Format: { "0" | "1" }
939 0 -- integrity auditing messages. (Default)
940 1 -- enable informational integrity auditing messages.
943 Format: { "sha1" | "md5" }
947 Load a policy which meets the needs of the Trusted
948 Computing Base. This means IMA will measure all
949 programs exec'd, files mmap'd for exec, and all files
950 opened for read by uid=0.
954 Run specified binary instead of /sbin/init as init
957 initcall_debug [KNL] Trace initcalls as they are executed. Useful
958 for working out where the kernel is dying during
961 initrd= [BOOT] Specify the location of the initial ramdisk
963 inport.irq= [HW] Inport (ATI XL and Microsoft) busmouse driver
966 intel_iommu= [DMAR] Intel IOMMU driver (DMAR) option
968 Enable intel iommu driver.
970 Disable intel iommu driver.
971 igfx_off [Default Off]
972 By default, gfx is mapped as normal device. If a gfx
973 device has a dedicated DMAR unit, the DMAR unit is
974 bypassed by not enabling DMAR with this option. In
975 this case, gfx device will use physical address for
978 With this option iommu will not optimize to look
979 for io virtual address below 32 bit forcing dual
980 address cycle on pci bus for cards supporting greater
981 than 32 bit addressing. The default is to look
982 for translation below 32 bit and if not available
983 then look in the higher range.
985 With this option on every unmap_single operation will
986 result in a hardware IOTLB flush operation as opposed
987 to batching them for performance.
989 intremap= [X86-64, Intel-IOMMU]
990 Format: { on (default) | off | nosid }
991 on enable Interrupt Remapping (default)
992 off disable Interrupt Remapping
993 nosid disable Source ID checking
997 iomem= Disable strict checking of access to MMIO memory
998 strict regions from userspace.
1014 io7= [HW] IO7 for Marvel based alpha systems
1015 See comment before marvel_specify_io7 in
1016 arch/alpha/kernel/core_marvel.c.
1018 io_delay= [X86] I/O delay method
1020 Standard port 0x80 based delay
1022 Alternate port 0xed based delay (needed on some systems)
1024 Simple two microseconds delay
1029 See Documentation/filesystems/nfs/nfsroot.txt.
1031 ip2= [HW] Set IO/IRQ pairs for up to 4 IntelliPort boards
1032 See comment before ip2_setup() in
1033 drivers/char/ip2/ip2base.c.
1036 When an interrupt is not handled search all handlers
1037 for it. Intended to get systems with badly broken
1041 When an interrupt is not handled search all handlers
1042 for it. Also check all handlers each timer
1043 interrupt. Intended to get systems with badly broken
1047 Format: <RDP>,<reset>,<pci_scan>,<verbosity>
1049 isolcpus= [KNL,SMP] Isolate CPUs from the general scheduler.
1051 <cpu number>,...,<cpu number>
1053 <cpu number>-<cpu number>
1054 (must be a positive range in ascending order)
1056 <cpu number>,...,<cpu number>-<cpu number>
1058 This option can be used to specify one or more CPUs
1059 to isolate from the general SMP balancing and scheduling
1060 algorithms. You can move a process onto or off an
1061 "isolated" CPU via the CPU affinity syscalls or cpuset.
1062 <cpu number> begins at 0 and the maximum value is
1063 "number of CPUs in system - 1".
1065 This option is the preferred way to isolate CPUs. The
1066 alternative -- manually setting the CPU mask of all
1067 tasks in the system -- can cause problems and
1068 suboptimal load balancer performance.
1072 js= [HW,JOY] Analog joystick
1073 See Documentation/input/joystick.txt.
1077 kernelcore=nn[KMG] [KNL,X86,IA-64,PPC] This parameter
1078 specifies the amount of memory usable by the kernel
1079 for non-movable allocations. The requested amount is
1080 spread evenly throughout all nodes in the system. The
1081 remaining memory in each node is used for Movable
1082 pages. In the event, a node is too small to have both
1083 kernelcore and Movable pages, kernelcore pages will
1084 take priority and other nodes will have a larger number
1085 of kernelcore pages. The Movable zone is used for the
1086 allocation of pages that may be reclaimed or moved
1087 by the page migration subsystem. This means that
1088 HugeTLB pages may not be allocated from this zone.
1089 Note that allocations like PTEs-from-HighMem still
1090 use the HighMem zone if it exists, and the Normal
1091 zone if it does not.
1093 kgdbdbgp= [KGDB,HW] kgdb over EHCI usb debug port.
1094 Format: <Controller#>[,poll interval]
1095 The controller # is the number of the ehci usb debug
1096 port as it is probed via PCI. The poll interval is
1097 optional and is the number seconds in between
1098 each poll cycle to the debug port in case you need
1099 the functionality for interrupting the kernel with
1100 gdb or control-c on the dbgp connection. When
1101 not using this parameter you use sysrq-g to break into
1102 the kernel debugger.
1104 kgdboc= [KGDB,HW] kgdb over consoles.
1105 Requires a tty driver that supports console polling,
1106 or a supported polling keyboard driver (non-usb).
1107 Serial only format: <serial_device>[,baud]
1108 keyboard only format: kbd
1109 keyboard and serial format: kbd,<serial_device>[,baud]
1110 Optional Kernel mode setting:
1111 kms, kbd format: kms,kbd
1112 kms, kbd and serial format: kms,kbd,<ser_dev>[,baud]
1114 kgdbwait [KGDB] Stop kernel execution and enter the
1115 kernel debugger at the earliest opportunity.
1117 kmac= [MIPS] korina ethernet MAC address.
1118 Configure the RouterBoard 532 series on-chip
1119 Ethernet adapter MAC address.
1121 kmemleak= [KNL] Boot-time kmemleak enable/disable
1122 Valid arguments: on, off
1125 kstack=N [X86] Print N words from the kernel stack
1128 kvm.ignore_msrs=[KVM] Ignore guest accesses to unhandled MSRs.
1129 Default is 0 (don't ignore, but inject #GP)
1131 kvm.oos_shadow= [KVM] Disable out-of-sync shadow paging.
1132 Default is 1 (enabled)
1134 kvm-amd.nested= [KVM,AMD] Allow nested virtualization in KVM/SVM.
1137 kvm-amd.npt= [KVM,AMD] Disable nested paging (virtualized MMU)
1139 Default is 1 (enabled) if in 64bit or 32bit-PAE mode
1141 kvm-intel.bypass_guest_pf=
1142 [KVM,Intel] Disables bypassing of guest page faults
1143 on Intel chips. Default is 1 (enabled)
1145 kvm-intel.ept= [KVM,Intel] Disable extended page tables
1146 (virtualized MMU) support on capable Intel chips.
1147 Default is 1 (enabled)
1149 kvm-intel.emulate_invalid_guest_state=
1150 [KVM,Intel] Enable emulation of invalid guest states
1151 Default is 0 (disabled)
1153 kvm-intel.flexpriority=
1154 [KVM,Intel] Disable FlexPriority feature (TPR shadow).
1155 Default is 1 (enabled)
1157 kvm-intel.unrestricted_guest=
1158 [KVM,Intel] Disable unrestricted guest feature
1159 (virtualized real and unpaged mode) on capable
1160 Intel chips. Default is 1 (enabled)
1162 kvm-intel.vpid= [KVM,Intel] Disable Virtual Processor Identification
1163 feature (tagged TLBs) on capable Intel chips.
1164 Default is 1 (enabled)
1170 lapic [X86-32,APIC] Enable the local APIC even if BIOS
1173 lapic_timer_c2_ok [X86,APIC] trust the local apic timer
1176 libata.dma= [LIBATA] DMA control
1177 libata.dma=0 Disable all PATA and SATA DMA
1178 libata.dma=1 PATA and SATA Disk DMA only
1179 libata.dma=2 ATAPI (CDROM) DMA only
1180 libata.dma=4 Compact Flash DMA only
1181 Combinations also work, so libata.dma=3 enables DMA
1182 for disks and CDROMs, but not CFs.
1184 libata.ignore_hpa= [LIBATA] Ignore HPA limit
1185 libata.ignore_hpa=0 keep BIOS limits (default)
1186 libata.ignore_hpa=1 ignore limits, using full disk
1188 libata.noacpi [LIBATA] Disables use of ACPI in libata suspend/resume
1192 libata.force= [LIBATA] Force configurations. The format is comma
1193 separated list of "[ID:]VAL" where ID is
1194 PORT[.DEVICE]. PORT and DEVICE are decimal numbers
1195 matching port, link or device. Basically, it matches
1196 the ATA ID string printed on console by libata. If
1197 the whole ID part is omitted, the last PORT and DEVICE
1198 values are used. If ID hasn't been specified yet, the
1199 configuration applies to all ports, links and devices.
1201 If only DEVICE is omitted, the parameter applies to
1202 the port and all links and devices behind it. DEVICE
1203 number of 0 either selects the first device or the
1204 first fan-out link behind PMP device. It does not
1205 select the host link. DEVICE number of 15 selects the
1206 host link and device attached to it.
1208 The VAL specifies the configuration to force. As long
1209 as there's no ambiguity shortcut notation is allowed.
1210 For example, both 1.5 and 1.5G would work for 1.5Gbps.
1211 The following configurations can be forced.
1213 * Cable type: 40c, 80c, short40c, unk, ign or sata.
1214 Any ID with matching PORT is used.
1216 * SATA link speed limit: 1.5Gbps or 3.0Gbps.
1218 * Transfer mode: pio[0-7], mwdma[0-4] and udma[0-7].
1219 udma[/][16,25,33,44,66,100,133] notation is also
1222 * [no]ncq: Turn on or off NCQ.
1224 * nohrst, nosrst, norst: suppress hard, soft
1227 * dump_id: dump IDENTIFY data.
1229 If there are multiple matching configurations changing
1230 the same attribute, the last one is used.
1232 memblock=debug [KNL] Enable memblock debug messages.
1234 load_ramdisk= [RAM] List of ramdisks to load from floppy
1235 See Documentation/blockdev/ramdisk.txt.
1237 lockd.nlm_grace_period=P [NFS] Assign grace period.
1240 lockd.nlm_tcpport=N [NFS] Assign TCP port.
1243 lockd.nlm_timeout=T [NFS] Assign timeout value.
1246 lockd.nlm_udpport=M [NFS] Assign UDP port.
1249 logibm.irq= [HW,MOUSE] Logitech Bus Mouse Driver
1252 loglevel= All Kernel Messages with a loglevel smaller than the
1253 console loglevel will be printed to the console. It can
1254 also be changed with klogd or other programs. The
1255 loglevels are defined as follows:
1257 0 (KERN_EMERG) system is unusable
1258 1 (KERN_ALERT) action must be taken immediately
1259 2 (KERN_CRIT) critical conditions
1260 3 (KERN_ERR) error conditions
1261 4 (KERN_WARNING) warning conditions
1262 5 (KERN_NOTICE) normal but significant condition
1263 6 (KERN_INFO) informational
1264 7 (KERN_DEBUG) debug-level messages
1266 log_buf_len=n Sets the size of the printk ring buffer, in bytes.
1267 Format: { n | nk | nM }
1268 n must be a power of two. The default size
1269 is set in the kernel config file.
1271 logo.nologo [FB] Disables display of the built-in Linux logo.
1272 This may be used to provide more screen space for
1273 kernel log messages and is useful when debugging
1274 kernel boot problems.
1276 lp=0 [LP] Specify parallel ports to use, e.g,
1277 lp=port[,port...] lp=none,parport0 (lp0 not configured, lp1 uses
1278 lp=reset first parallel port). 'lp=0' disables the
1279 lp=auto printer driver. 'lp=reset' (which can be
1280 specified in addition to the ports) causes
1281 attached printers to be reset. Using
1282 lp=port1,port2,... specifies the parallel ports
1283 to associate lp devices with, starting with
1284 lp0. A port specification may be 'none' to skip
1285 that lp device, or a parport name such as
1286 'parport0'. Specifying 'lp=auto' instead of a
1287 port specification list means that device IDs
1288 from each port should be examined, to see if
1289 an IEEE 1284-compliant printer is attached; if
1290 so, the driver will manage that printer.
1291 See also header of drivers/char/lp.c.
1294 Sets loops_per_jiffy to given constant, thus avoiding
1295 time-consuming boot-time autodetection (up to 250 ms per
1296 CPU). 0 enables autodetection (default). To determine
1297 the correct value for your kernel, boot with normal
1298 autodetection and see what value is printed. Note that
1299 on SMP systems the preset will be applied to all CPUs,
1300 which is likely to cause problems if your CPUs need
1301 significantly divergent settings. An incorrect value
1302 will cause delays in the kernel to be wrong, leading to
1303 unpredictable I/O errors and other breakage. Although
1304 unlikely, in the extreme case this might damage your
1308 Format: <io>,<irq>,<dma>
1310 machvec= [IA64] Force the use of a particular machine-vector
1311 (machvec) in a generic kernel.
1312 Example: machvec=hpzx1_swiotlb
1314 machtype= [Loongson] Share the same kernel image file between different
1316 Example: machtype=lemote-yeeloong-2f-7inch
1318 max_addr=nn[KMG] [KNL,BOOT,ia64] All physical memory greater
1319 than or equal to this physical address is ignored.
1321 maxcpus= [SMP] Maximum number of processors that an SMP kernel
1322 should make use of. maxcpus=n : n >= 0 limits the
1323 kernel to using 'n' processors. n=0 is a special case,
1324 it is equivalent to "nosmp", which also disables
1327 max_loop= [LOOP] Maximum number of loopback devices that can
1333 mce [X86-32] Machine Check Exception
1335 mce=option [X86-64] See Documentation/x86/x86_64/boot-options.txt
1337 md= [HW] RAID subsystems devices and level
1338 See Documentation/md.txt.
1341 Format: <first>,<last>
1342 Specifies range of consoles to be captured by the MDA.
1344 mem=nn[KMG] [KNL,BOOT] Force usage of a specific amount of memory
1345 Amount of memory to be used when the kernel is not able
1346 to see the whole system memory or for test.
1347 [X86-32] Use together with memmap= to avoid physical
1348 address space collisions. Without memmap= PCI devices
1349 could be placed at addresses belonging to unused RAM.
1351 mem=nopentium [BUGS=X86-32] Disable usage of 4MB pages for kernel
1355 [KNL,SH] Allow user to override the default size for
1356 per-device physically contiguous DMA buffers.
1358 memmap=exactmap [KNL,X86] Enable setting of an exact
1359 E820 memory map, as specified by the user.
1360 Such memmap=exactmap lines can be constructed based on
1361 BIOS output or other requirements. See the memmap=nn@ss
1364 memmap=nn[KMG]@ss[KMG]
1365 [KNL] Force usage of a specific region of memory
1366 Region of memory to be used, from ss to ss+nn.
1368 memmap=nn[KMG]#ss[KMG]
1369 [KNL,ACPI] Mark specific memory as ACPI data.
1370 Region of memory to be used, from ss to ss+nn.
1372 memmap=nn[KMG]$ss[KMG]
1373 [KNL,ACPI] Mark specific memory as reserved.
1374 Region of memory to be used, from ss to ss+nn.
1375 Example: Exclude memory from 0x18690000-0x1869ffff
1376 memmap=64K$0x18690000
1378 memmap=0x10000$0x18690000
1380 memory_corruption_check=0/1 [X86]
1381 Some BIOSes seem to corrupt the first 64k of
1382 memory when doing things like suspend/resume.
1383 Setting this option will scan the memory
1384 looking for corruption. Enabling this will
1385 both detect corruption and prevent the kernel
1386 from using the memory being corrupted.
1387 However, its intended as a diagnostic tool; if
1388 repeatable BIOS-originated corruption always
1389 affects the same memory, you can use memmap=
1390 to prevent the kernel from using that memory.
1392 memory_corruption_check_size=size [X86]
1393 By default it checks for corruption in the low
1394 64k, making this memory unavailable for normal
1395 use. Use this parameter to scan for
1396 corruption in more or less memory.
1398 memory_corruption_check_period=seconds [X86]
1399 By default it checks for corruption every 60
1400 seconds. Use this parameter to check at some
1401 other rate. 0 disables periodic checking.
1403 memtest= [KNL,X86] Enable memtest
1405 default : 0 <disable>
1406 Specifies the number of memtest passes to be
1407 performed. Each pass selects another test
1408 pattern from a given set of patterns. Memtest
1409 fills the memory with this pattern, validates
1410 memory contents and reserves bad memory
1411 regions that are detected.
1413 meye.*= [HW] Set MotionEye Camera parameters
1414 See Documentation/video4linux/meye.txt.
1416 mfgpt_irq= [IA-32] Specify the IRQ to use for the
1417 Multi-Function General Purpose Timers on AMD Geode
1420 mfgptfix [X86-32] Fix MFGPT timers on AMD Geode platforms when
1421 the BIOS has incorrectly applied a workaround. TinyBIOS
1422 version 0.98 is known to be affected, 0.99 fixes the
1423 problem by letting the user disable the workaround.
1427 min_addr=nn[KMG] [KNL,BOOT,ia64] All physical memory below this
1428 physical address is ignored.
1430 mini2440= [ARM,HW,KNL]
1431 Format:[0..2][b][c][t]
1433 MINI2440 configuration specification:
1434 0 - The attached screen is the 3.5" TFT
1435 1 - The attached screen is the 7" TFT
1436 2 - The VGA Shield is attached (1024x768)
1437 Leaving out the screen size parameter will not load
1438 the TFT driver, and the framebuffer will be left
1440 b - Enable backlight. The TFT backlight pin will be
1441 linked to the kernel VESA blanking code and a GPIO
1442 LED. This parameter is not necessary when using the
1444 c - Enable the s3c camera interface.
1445 t - Reserved for enabling touchscreen support. The
1446 touchscreen support is not enabled in the mainstream
1447 kernel as of 2.6.30, a preliminary port can be found
1448 in the "bleeding edge" mini2440 support kernel at
1449 http://repo.or.cz/w/linux-2.6/mini2440.git
1452 [KNL] When CONFIG_DEBUG_MEMORY_INIT is set, this
1453 parameter allows control of the logging verbosity for
1454 the additional memory initialisation checks. A value
1455 of 0 disables mminit logging and a level of 4 will
1456 log everything. Information is printed at KERN_DEBUG
1457 so loglevel=8 may also need to be specified.
1460 [MOUSE] Maximum time between finger touching and
1461 leaving touchpad surface for touch to be considered
1462 a tap and be reported as a left button click (for
1463 touchpads working in absolute mode only).
1465 mousedev.xres= [MOUSE] Horizontal screen resolution, used for devices
1466 reporting absolute coordinates, such as tablets
1467 mousedev.yres= [MOUSE] Vertical screen resolution, used for devices
1468 reporting absolute coordinates, such as tablets
1470 movablecore=nn[KMG] [KNL,X86,IA-64,PPC] This parameter
1471 is similar to kernelcore except it specifies the
1472 amount of memory used for migratable allocations.
1473 If both kernelcore and movablecore is specified,
1474 then kernelcore will be at *least* the specified
1475 value but may be more. If movablecore on its own
1476 is specified, the administrator must be careful
1477 that the amount of memory usable for all allocations
1480 MTD_Partition= [MTD]
1481 Format: <name>,<region-number>,<size>,<offset>
1483 MTD_Region= [MTD] Format:
1484 <name>,<region-number>[,<base>,<size>,<buswidth>,<altbuswidth>]
1487 See drivers/mtd/cmdlinepart.c.
1489 onenand.bdry= [HW,MTD] Flex-OneNAND Boundary Configuration
1491 Format: [die0_boundary][,die0_lock][,die1_boundary][,die1_lock]
1493 boundary - index of last SLC block on Flex-OneNAND.
1494 The remaining blocks are configured as MLC blocks.
1495 lock - Configure if Flex-OneNAND boundary should be locked.
1496 Once locked, the boundary cannot be changed.
1497 1 indicates lock status, 0 indicates unlock status.
1500 ARM/S3C2412 JIVE boot control
1502 See arch/arm/mach-s3c2412/mach-jive.c
1504 mtouchusb.raw_coordinates=
1505 [HW] Make the MicroTouch USB driver use raw coordinates
1506 ('y', default) or cooked coordinates ('n')
1508 mtrr_chunk_size=nn[KMG] [X86]
1509 used for mtrr cleanup. It is largest continuous chunk
1510 that could hold holes aka. UC entries.
1512 mtrr_gran_size=nn[KMG] [X86]
1513 Used for mtrr cleanup. It is granularity of mtrr block.
1515 Large value could prevent small alignment from
1518 mtrr_spare_reg_nr=n [X86]
1520 Range: 0,7 : spare reg number
1522 Used for mtrr cleanup. It is spare mtrr entries number.
1523 Set to 2 or more if your graphical card needs more.
1525 n2= [NET] SDL Inc. RISCom/N2 synchronous serial card
1527 netdev= [NET] Network devices parameters
1528 Format: <irq>,<io>,<mem_start>,<mem_end>,<name>
1529 Note that mem_start is often overloaded to mean
1530 something different and driver-specific.
1531 This usage is only documented in each driver source
1535 [NETFILTER] Enable connection tracking flow accounting
1536 0 to disable accounting
1537 1 to enable accounting
1541 See Documentation/filesystems/nfs/nfsroot.txt.
1543 nfsroot= [NFS] nfs root filesystem for disk-less boxes.
1544 See Documentation/filesystems/nfs/nfsroot.txt.
1546 nfs.callback_tcpport=
1547 [NFS] set the TCP port on which the NFSv4 callback
1548 channel should listen.
1551 [NFS] sets the pathname to the program which is used
1552 to update the NFS client cache entries.
1554 nfs.cache_getent_timeout=
1555 [NFS] sets the timeout after which an attempt to
1556 update a cache entry is deemed to have failed.
1558 nfs.idmap_cache_timeout=
1559 [NFS] set the maximum lifetime for idmapper cache
1563 [NFS] enable 64-bit inode numbers.
1564 If zero, the NFS client will fake up a 32-bit inode
1565 number for the readdir() and stat() syscalls instead
1566 of returning the full 64-bit number.
1567 The default is to return 64-bit inode numbers.
1569 nmi_debug= [KNL,AVR32,SH] Specify one or more actions to take
1570 when a NMI is triggered.
1571 Format: [state][,regs][,debounce][,die]
1573 nmi_watchdog= [KNL,BUGS=X86] Debugging features for SMP kernels
1574 Format: [panic,][num]
1576 0 - turn nmi_watchdog off
1577 1 - use the IO-APIC timer for the NMI watchdog
1578 2 - use the local APIC for the NMI watchdog using
1579 a performance counter. Note: This will use one
1580 performance counter and the local APIC's performance
1582 When panic is specified, panic when an NMI watchdog
1584 This is useful when you use a panic=... timeout and
1585 need the box quickly up again.
1586 Instead of 1 and 2 it is possible to use the following
1587 symbolic names: lapic and ioapic
1588 Example: nmi_watchdog=2 or nmi_watchdog=panic,lapic
1590 netpoll.carrier_timeout=
1591 [NET] Specifies amount of time (in seconds) that
1592 netpoll should wait for a carrier. By default netpoll
1595 no387 [BUGS=X86-32] Tells the kernel to use the 387 maths
1596 emulation library even if a 387 maths coprocessor
1600 [HW] Never suspend the console
1601 Disable suspending of consoles during suspend and
1602 hibernate operations. Once disabled, debugging
1603 messages can reach various consoles while the rest
1604 of the system is being put to sleep (ie, while
1605 debugging driver suspend/resume hooks). This may
1606 not work reliably with all consoles, but is known
1607 to work with serial and VGA consoles.
1609 noaliencache [MM, NUMA, SLAB] Disables the allocation of alien
1610 caches in the slab allocator. Saves per-node memory,
1611 but will impact performance.
1615 noapic [SMP,APIC] Tells the kernel to not make use of any
1616 IOAPICs that may be present in the system.
1618 nobats [PPC] Do not use BATs for mapping kernel lowmem
1619 on "Classic" PPC cores.
1623 noclflush [BUGS=X86] Don't use the CLFLUSH instruction
1625 nodelayacct [KNL] Disable per-task delay accounting
1627 nodisconnect [HW,SCSI,M68K] Disables SCSI disconnects.
1629 nodsp [SH] Disable hardware DSP at boot time.
1631 noefi [X86] Disable EFI runtime services support.
1636 On X86-32 available only on PAE configured kernels.
1637 noexec=on: enable non-executable mappings (default)
1638 noexec=off: disable non-executable mappings
1641 This affects only 32-bit executables.
1642 noexec32=on: enable non-executable mappings (default)
1643 read doesn't imply executable mappings
1644 noexec32=off: disable non-executable mappings
1645 read implies executable mappings
1647 nofpu [SH] Disable hardware FPU at boot time.
1649 nofxsr [BUGS=X86-32] Disables x86 floating point extended
1650 register save and restore. The kernel will only save
1651 legacy floating-point registers on task switch.
1653 noxsave [BUGS=X86] Disables x86 extended register state save
1654 and restore using xsave. The kernel will fallback to
1655 enabling legacy floating-point and sse state.
1657 nohlt [BUGS=ARM,SH] Tells the kernel that the sleep(SH) or
1658 wfi(ARM) instruction doesn't work correctly and not to
1659 use it. This is also useful when using JTAG debugger.
1661 no-hlt [BUGS=X86-32] Tells the kernel that the hlt
1662 instruction doesn't work correctly and not to
1665 no_file_caps Tells the kernel not to honor file capabilities. The
1666 only way then for a file to be executed with privilege
1667 is to be setuid root or executed by root.
1669 nohalt [IA-64] Tells the kernel not to use the power saving
1670 function PAL_HALT_LIGHT when idle. This increases
1671 power-consumption. On the positive side, it reduces
1672 interrupt wake-up latency, which may improve performance
1673 in certain environments such as networked servers or
1676 nohz= [KNL] Boottime enable/disable dynamic ticks
1677 Valid arguments: on, off
1680 noiotrap [SH] Disables trapped I/O port accesses.
1682 noirqdebug [X86-32] Disables the code which attempts to detect and
1683 disable unhandled interrupt sources.
1685 no_timer_check [X86,APIC] Disables the code which tests for
1686 broken timer IRQ sources.
1688 noisapnp [ISAPNP] Disables ISA PnP code.
1690 noinitrd [RAM] Tells the kernel not to load any configured
1693 nointremap [X86-64, Intel-IOMMU] Do not enable interrupt
1695 [Deprecated - use intremap=off]
1699 nojitter [IA64] Disables jitter checking for ITC timers.
1701 nolapic [X86-32,APIC] Do not enable or use the local APIC.
1703 nolapic_timer [X86-32,APIC] Do not use the local APIC timer.
1705 noltlbs [PPC] Do not use large page/tlb entries for kernel
1706 lowmem mapping on PPC40x.
1708 nomca [IA-64] Disable machine check abort handling
1710 nomce [X86-32] Machine Check Exception
1712 nomfgpt [X86-32] Disable Multi-Function General Purpose
1713 Timer usage (for AMD Geode machines).
1715 nopat [X86] Disable PAT (page attribute table extension of
1716 pagetables) support.
1718 norandmaps Don't use address space randomization. Equivalent to
1719 echo 0 > /proc/sys/kernel/randomize_va_space
1721 noreplace-paravirt [X86-32,PV_OPS] Don't patch paravirt_ops
1723 noreplace-smp [X86-32,SMP] Don't replace SMP instructions
1724 with UP alternatives
1726 noresidual [PPC] Don't use residual data on PReP machines.
1728 noresume [SWSUSP] Disables resume and restores original swap
1731 no-scroll [VGA] Disables scrollback.
1732 This is required for the Braillex ib80-piezo Braille
1733 reader made by F.H. Papenmeier (Germany).
1737 nosep [BUGS=X86-32] Disables x86 SYSENTER/SYSEXIT support.
1739 nosmp [SMP] Tells an SMP kernel to act as a UP kernel,
1740 and disable the IO APIC. legacy for "maxcpus=0".
1742 nosoftlockup [KNL] Disable the soft-lockup detector.
1744 noswapaccount [KNL] Disable accounting of swap in memory resource
1745 controller. (See Documentation/cgroups/memory.txt)
1747 nosync [HW,M68K] Disables sync negotiation for all devices.
1749 notsc [BUGS=X86-32] Disable Time Stamp Counter
1751 nousb [USB] Disable the USB subsystem
1753 nowatchdog [KNL] Disable the lockup detector.
1757 nox2apic [X86-64,APIC] Do not enable x2APIC mode.
1759 nptcg= [IA64] Override max number of concurrent global TLB
1760 purges which is reported from either PAL_VM_SUMMARY or
1763 nr_cpus= [SMP] Maximum number of processors that an SMP kernel
1764 could support. nr_cpus=n : n >= 1 limits the kernel to
1765 supporting 'n' processors. Later in runtime you can not
1766 use hotplug cpu feature to put more cpu back to online.
1767 just like you compile the kernel NR_CPUS=n
1769 nr_uarts= [SERIAL] maximum number of UARTs to be registered.
1771 numa_zonelist_order= [KNL, BOOT] Select zonelist order for NUMA.
1772 one of ['zone', 'node', 'default'] can be specified
1773 This can be set from sysctl after boot.
1774 See Documentation/sysctl/vm.txt for details.
1776 ohci1394_dma=early [HW] enable debugging via the ohci1394 driver.
1777 See Documentation/debugging-via-ohci1394.txt for more
1780 olpc_ec_timeout= [OLPC] ms delay when issuing EC commands
1781 Rather than timing out after 20 ms if an EC
1782 command is not properly ACKed, override the length
1783 of the timeout. We have interrupts disabled while
1784 waiting for the ACK, so if this is set too high
1785 interrupts *may* be lost!
1787 omap_mux= [OMAP] Override bootloader pin multiplexing.
1788 Format: <mux_mode0.mode_name=value>...
1789 For example, to override I2C bus2:
1790 omap_mux=i2c2_scl.i2c2_scl=0x100,i2c2_sda.i2c2_sda=0x100
1792 oprofile.timer= [HW]
1793 Use timer interrupt instead of performance counters
1795 oprofile.cpu_type= Force an oprofile cpu type
1796 This might be useful if you have an older oprofile
1797 userland or if you want common events.
1798 Format: { arch_perfmon }
1799 arch_perfmon: [X86] Force use of architectural
1800 perfmon on Intel CPUs instead of the
1801 CPU specific event set.
1804 See Documentation/sound/oss/oss-parameters.txt
1806 panic= [KNL] Kernel behaviour on panic
1809 parkbd.port= [HW] Parallel port number the keyboard adapter is
1810 connected to, default is 0.
1812 parkbd.mode= [HW] Parallel port keyboard adapter mode of operation,
1813 0 for XT, 1 for AT (default is AT).
1816 parport= [HW,PPT] Specify parallel ports. 0 disables.
1817 Format: { 0 | auto | 0xBBB[,IRQ[,DMA]] }
1818 Use 'auto' to force the driver to use any
1819 IRQ/DMA settings detected (the default is to
1820 ignore detected IRQ/DMA settings because of
1821 possible conflicts). You can specify the base
1822 address, IRQ, and DMA settings; IRQ and DMA
1823 should be numbers, or 'auto' (for using detected
1824 settings on that particular port), or 'nofifo'
1825 (to avoid using a FIFO even if it is detected).
1826 Parallel ports are assigned in the order they
1827 are specified on the command line, starting
1830 parport_init_mode= [HW,PPT]
1831 Configure VIA parallel port to operate in
1832 a specific mode. This is necessary on Pegasos
1833 computer where firmware has no options for setting
1834 up parallel port mode and sets it to spp.
1835 Currently this function knows 686a and 8231 chips.
1836 Format: [spp|ps2|epp|ecp|ecpepp]
1839 Halt all CPUs after the first oops has been printed for
1840 the specified number of seconds. This is to be used if
1841 your oopses keep scrolling off the screen.
1846 See header of drivers/block/paride/pcd.c.
1847 See also Documentation/blockdev/paride.txt.
1849 pci=option[,option...] [PCI] various PCI subsystem options:
1850 earlydump [X86] dump PCI config space before the kernel
1852 off [X86] don't probe for the PCI bus
1853 bios [X86-32] force use of PCI BIOS, don't access
1854 the hardware directly. Use this if your machine
1855 has a non-standard PCI host bridge.
1856 nobios [X86-32] disallow use of PCI BIOS, only direct
1857 hardware access methods are allowed. Use this
1858 if you experience crashes upon bootup and you
1859 suspect they are caused by the BIOS.
1860 conf1 [X86] Force use of PCI Configuration
1862 conf2 [X86] Force use of PCI Configuration
1864 noaer [PCIE] If the PCIEAER kernel config parameter is
1865 enabled, this kernel boot option can be used to
1866 disable the use of PCIE advanced error reporting.
1867 nodomains [PCI] Disable support for multiple PCI
1868 root domains (aka PCI segments, in ACPI-speak).
1869 nommconf [X86] Disable use of MMCONFIG for PCI
1871 check_enable_amd_mmconf [X86] check for and enable
1872 properly configured MMIO access to PCI
1873 config space on AMD family 10h CPU
1874 nomsi [MSI] If the PCI_MSI kernel config parameter is
1875 enabled, this kernel boot option can be used to
1876 disable the use of MSI interrupts system-wide.
1877 noioapicquirk [APIC] Disable all boot interrupt quirks.
1878 Safety option to keep boot IRQs enabled. This
1879 should never be necessary.
1880 ioapicreroute [APIC] Enable rerouting of boot IRQs to the
1881 primary IO-APIC for bridges that cannot disable
1882 boot IRQs. This fixes a source of spurious IRQs
1883 when the system masks IRQs.
1884 noioapicreroute [APIC] Disable workaround that uses the
1885 boot IRQ equivalent of an IRQ that connects to
1886 a chipset where boot IRQs cannot be disabled.
1887 The opposite of ioapicreroute.
1888 biosirq [X86-32] Use PCI BIOS calls to get the interrupt
1889 routing table. These calls are known to be buggy
1890 on several machines and they hang the machine
1891 when used, but on other computers it's the only
1892 way to get the interrupt routing table. Try
1893 this option if the kernel is unable to allocate
1894 IRQs or discover secondary PCI buses on your
1896 rom [X86] Assign address space to expansion ROMs.
1897 Use with caution as certain devices share
1898 address decoders between ROMs and other
1900 norom [X86] Do not assign address space to
1901 expansion ROMs that do not already have
1902 BIOS assigned address ranges.
1903 nobar [X86] Do not assign address space to the
1904 BARs that weren't assigned by the BIOS.
1905 irqmask=0xMMMM [X86] Set a bit mask of IRQs allowed to be
1906 assigned automatically to PCI devices. You can
1907 make the kernel exclude IRQs of your ISA cards
1909 pirqaddr=0xAAAAA [X86] Specify the physical address
1910 of the PIRQ table (normally generated
1911 by the BIOS) if it is outside the
1912 F0000h-100000h range.
1913 lastbus=N [X86] Scan all buses thru bus #N. Can be
1914 useful if the kernel is unable to find your
1915 secondary buses and you want to tell it
1916 explicitly which ones they are.
1917 assign-busses [X86] Always assign all PCI bus
1918 numbers ourselves, overriding
1919 whatever the firmware may have done.
1920 usepirqmask [X86] Honor the possible IRQ mask stored
1921 in the BIOS $PIR table. This is needed on
1922 some systems with broken BIOSes, notably
1923 some HP Pavilion N5400 and Omnibook XE3
1924 notebooks. This will have no effect if ACPI
1925 IRQ routing is enabled.
1926 noacpi [X86] Do not use ACPI for IRQ routing
1927 or for PCI scanning.
1928 use_crs [X86] Use PCI host bridge window information
1929 from ACPI. On BIOSes from 2008 or later, this
1930 is enabled by default. If you need to use this,
1931 please report a bug.
1932 nocrs [X86] Ignore PCI host bridge windows from ACPI.
1933 If you need to use this, please report a bug.
1934 routeirq Do IRQ routing for all PCI devices.
1935 This is normally done in pci_enable_device(),
1936 so this option is a temporary workaround
1937 for broken drivers that don't call it.
1938 skip_isa_align [X86] do not align io start addr, so can
1939 handle more pci cards
1940 firmware [ARM] Do not re-enumerate the bus but instead
1941 just use the configuration from the
1942 bootloader. This is currently used on
1943 IXP2000 systems where the bus has to be
1944 configured a certain way for adjunct CPUs.
1945 noearly [X86] Don't do any early type 1 scanning.
1946 This might help on some broken boards which
1947 machine check when some devices' config space
1948 is read. But various workarounds are disabled
1949 and some IOMMU drivers will not work.
1950 bfsort Sort PCI devices into breadth-first order.
1951 This sorting is done to get a device
1952 order compatible with older (<= 2.4) kernels.
1953 nobfsort Don't sort PCI devices into breadth-first order.
1954 cbiosize=nn[KMG] The fixed amount of bus space which is
1955 reserved for the CardBus bridge's IO window.
1956 The default value is 256 bytes.
1957 cbmemsize=nn[KMG] The fixed amount of bus space which is
1958 reserved for the CardBus bridge's memory
1959 window. The default value is 64 megabytes.
1962 [<order of align>@][<domain>:]<bus>:<slot>.<func>[; ...]
1963 Specifies alignment and device to reassign
1964 aligned memory resources.
1965 If <order of align> is not specified,
1966 PAGE_SIZE is used as alignment.
1967 PCI-PCI bridge can be specified, if resource
1968 windows need to be expanded.
1969 ecrc= Enable/disable PCIe ECRC (transaction layer
1970 end-to-end CRC checking).
1971 bios: Use BIOS/firmware settings. This is the
1976 pcie_aspm= [PCIE] Forcibly enable or disable PCIe Active State Power
1979 force Enable ASPM even on devices that claim not to support it.
1980 WARNING: Forcing ASPM on may cause system lockups.
1982 pcie_ports= [PCIE] PCIe ports handling:
1983 auto Ask the BIOS whether or not to use native PCIe services
1984 associated with PCIe ports (PME, hot-plug, AER). Use
1985 them only if that is allowed by the BIOS.
1986 native Use native PCIe services associated with PCIe ports
1988 compat Treat PCIe ports as PCI-to-PCI bridges, disable the PCIe
1991 pcie_pme= [PCIE,PM] Native PCIe PME signaling options:
1992 nomsi Do not use MSI for native PCIe PME signaling (this makes
1993 all PCIe root ports use INTx for all services).
1995 pcmv= [HW,PCMCIA] BadgePAD 4
1998 See Documentation/blockdev/paride.txt.
2000 pdcchassis= [PARISC,HW] Disable/Enable PDC Chassis Status codes at
2003 See arch/parisc/kernel/pdc_chassis.c
2005 percpu_alloc= Select which percpu first chunk allocator to use.
2006 Currently supported values are "embed" and "page".
2007 Archs may support subset or none of the selections.
2008 See comments in mm/percpu.c for details on each
2009 allocator. This parameter is primarily for debugging
2010 and performance comparison.
2013 See Documentation/blockdev/paride.txt.
2016 See Documentation/blockdev/paride.txt.
2018 pirq= [SMP,APIC] Manual mp-table setup
2019 See Documentation/x86/i386/IO-APIC.txt.
2021 plip= [PPT,NET] Parallel port network link
2022 Format: { parport<nr> | timid | 0 }
2023 See also Documentation/parport.txt.
2025 pmtmr= [X86] Manual setup of pmtmr I/O Port.
2026 Override pmtimer IOPort with a hex value.
2030 Enable PNP debug messages. This depends on the
2031 CONFIG_PNP_DEBUG_MESSAGES option.
2037 { on | off | curr | res | no-curr | no-res }
2040 [ISAPNP] Exclude IRQs for the autoconfiguration
2043 [ISAPNP] Exclude DMAs for the autoconfiguration
2045 pnp_reserve_io= [ISAPNP] Exclude I/O ports for the autoconfiguration
2046 Ranges are in pairs (I/O port base and size).
2049 [ISAPNP] Exclude memory regions for the
2051 Ranges are in pairs (memory base and size).
2053 ports= [IP_VS_FTP] IPVS ftp helper module
2055 Up to 8 (IP_VS_APP_MAX_PORTS) ports
2057 Format: <port>,<port>....
2059 print-fatal-signals=
2060 [KNL] debug: print fatal signals
2062 If enabled, warn about various signal handling
2063 related application anomalies: too many signals,
2064 too many POSIX.1 timers, fatal signals causing a
2067 If you hit the warning due to signal overflow,
2068 you might want to try "ulimit -i unlimited".
2072 printk.time= Show timing data prefixed to each printk message line
2073 Format: <bool> (1/Y/y=enable, 0/N/n=disable)
2075 processor.max_cstate= [HW,ACPI]
2076 Limit processor to maximum C-state
2077 max_cstate=9 overrides any DMI blacklist limit.
2079 processor.nocst [HW,ACPI]
2080 Ignore the _CST method to determine C-states,
2081 instead using the legacy FADT method
2083 profile= [KNL] Enable kernel profiling via /proc/profile
2084 Format: [schedule,]<number>
2085 Param: "schedule" - profile schedule points.
2086 Param: <number> - step/bucket size as a power of 2 for
2087 statistical time based profiling.
2088 Param: "sleep" - profile D-state sleeping (millisecs).
2089 Requires CONFIG_SCHEDSTATS
2090 Param: "kvm" - profile VM exits.
2092 prompt_ramdisk= [RAM] List of RAM disks to prompt for floppy disk
2094 See Documentation/blockdev/ramdisk.txt.
2096 psmouse.proto= [HW,MOUSE] Highest PS2 mouse protocol extension to
2097 probe for; one of (bare|imps|exps|lifebook|any).
2098 psmouse.rate= [HW,MOUSE] Set desired mouse report rate, in reports
2100 psmouse.resetafter= [HW,MOUSE]
2101 Try to reset the device after so many bad packets
2104 [HW,MOUSE] Set desired mouse resolution, in dpi.
2105 psmouse.smartscroll=
2106 [HW,MOUSE] Controls Logitech smartscroll autorepeat.
2107 0 = disabled, 1 = enabled (default).
2110 See Documentation/blockdev/paride.txt.
2113 [KNL] Number of legacy pty's. Overwrites compiled-in
2116 quiet [KNL] Disable most log messages
2121 See Documentation/md.txt.
2123 ramdisk_blocksize= [RAM]
2124 See Documentation/blockdev/ramdisk.txt.
2126 ramdisk_size= [RAM] Sizes of RAM disks in kilobytes
2127 See Documentation/blockdev/ramdisk.txt.
2129 rcupdate.blimit= [KNL,BOOT]
2130 Set maximum number of finished RCU callbacks to process
2133 rcupdate.qhimark= [KNL,BOOT]
2134 Set threshold of queued
2135 RCU callbacks over which batch limiting is disabled.
2137 rcupdate.qlowmark= [KNL,BOOT]
2138 Set threshold of queued RCU callbacks below which
2139 batch limiting is re-enabled.
2143 Run specified binary instead of /init from the ramdisk,
2144 used for early userspace startup. See initrd.
2146 reboot= [BUGS=X86-32,BUGS=ARM,BUGS=IA-64] Rebooting mode
2147 Format: <reboot_mode>[,<reboot_mode2>[,...]]
2148 See arch/*/kernel/reboot.c or arch/*/kernel/process.c
2151 [KNL, SMP] Set scheduler's default relax_domain_level.
2152 See Documentation/cgroups/cpusets.txt.
2154 reserve= [KNL,BUGS] Force the kernel to ignore some iomem area
2156 reservetop= [X86-32]
2158 Reserves a hole at the top of the kernel virtual
2161 reset_devices [KNL] Force drivers to reset the underlying device
2162 during initialization.
2165 Specify the partition device for software suspend
2167 resume_offset= [SWSUSP]
2168 Specify the offset from the beginning of the partition
2169 given by "resume=" at which the swap header is located,
2170 in <PAGE_SIZE> units (needed only for swap files).
2171 See Documentation/power/swsusp-and-swap-files.txt
2173 retain_initrd [RAM] Keep initrd memory after extraction
2175 rhash_entries= [KNL,NET]
2176 Set number of hash buckets for route cache
2178 riscom8= [HW,SERIAL]
2179 Format: <io_board1>[,<io_board2>[,...<io_boardN>]]
2181 ro [KNL] Mount root device read-only on boot
2183 root= [KNL] Root filesystem
2185 rootdelay= [KNL] Delay (in seconds) to pause before attempting to
2186 mount the root filesystem
2188 rootflags= [KNL] Set root filesystem mount option string
2190 rootfstype= [KNL] Set root filesystem type
2192 rootwait [KNL] Wait (indefinitely) for root device to show up.
2193 Useful for devices that are detected asynchronously
2194 (e.g. USB and MMC devices).
2196 rw [KNL] Mount root device read-write on boot
2198 S [KNL] Run init in single mode
2201 See drivers/net/irda/sa1100_ir.c.
2203 sbni= [NET] Granch SBNI12 leased line adapter
2205 sched_debug [KNL] Enables verbose scheduler debug messages.
2207 security= [SECURITY] Choose a security module to enable at boot.
2208 If this boot parameter is not specified, only the first
2209 security module asking for security registration will be
2210 loaded. An invalid security module name will be treated
2211 as if no module has been chosen.
2213 selinux= [SELINUX] Disable or enable SELinux at boot time.
2214 Format: { "0" | "1" }
2215 See security/selinux/Kconfig help text.
2218 Default value is set via kernel config option.
2219 If enabled at boot time, /selinux/disable can be used
2220 later to disable prior to initial policy load.
2222 apparmor= [APPARMOR] Disable or enable AppArmor at boot time
2223 Format: { "0" | "1" }
2224 See security/apparmor/Kconfig help text
2227 Default value is set via kernel config option.
2229 serialnumber [BUGS=X86-32]
2232 Maximal number of shapers.
2234 show_msr= [x86] show boot-time MSR settings
2235 Format: { <integer> }
2236 Show boot-time (BIOS-initialized) MSR settings.
2237 The parameter means the number of CPUs to show,
2238 for example 1 means boot CPU only.
2245 slub_debug[=options[,slabs]] [MM, SLUB]
2246 Enabling slub_debug allows one to determine the
2247 culprit if slab objects become corrupted. Enabling
2248 slub_debug can create guard zones around objects and
2249 may poison objects when not in use. Also tracks the
2250 last alloc / free. For more information see
2251 Documentation/vm/slub.txt.
2253 slub_max_order= [MM, SLUB]
2254 Determines the maximum allowed order for slabs.
2255 A high setting may cause OOMs due to memory
2256 fragmentation. For more information see
2257 Documentation/vm/slub.txt.
2259 slub_min_objects= [MM, SLUB]
2260 The minimum number of objects per slab. SLUB will
2261 increase the slab order up to slub_max_order to
2262 generate a sufficiently large slab able to contain
2263 the number of objects indicated. The higher the number
2264 of objects the smaller the overhead of tracking slabs
2265 and the less frequently locks need to be acquired.
2266 For more information see Documentation/vm/slub.txt.
2268 slub_min_order= [MM, SLUB]
2269 Determines the mininum page order for slabs. Must be
2270 lower than slub_max_order.
2271 For more information see Documentation/vm/slub.txt.
2273 slub_nomerge [MM, SLUB]
2274 Disable merging of slabs with similar size. May be
2275 necessary if there is some reason to distinguish
2276 allocs to different slabs. Debug options disable
2277 merging on their own.
2278 For more information see Documentation/vm/slub.txt.
2281 Format: <io1>[,<io2>[,...,<io8>]]
2283 smp-alt-once [X86-32,SMP] On a hotplug CPU system, only
2284 attempt to substitute SMP alternatives once at boot.
2286 smsc-ircc2.nopnp [HW] Don't use PNP to discover SMC devices
2287 smsc-ircc2.ircc_cfg= [HW] Device configuration I/O port
2288 smsc-ircc2.ircc_sir= [HW] SIR base I/O port
2289 smsc-ircc2.ircc_fir= [HW] FIR base I/O port
2290 smsc-ircc2.ircc_irq= [HW] IRQ line
2291 smsc-ircc2.ircc_dma= [HW] DMA channel
2292 smsc-ircc2.ircc_transceiver= [HW] Transceiver type:
2293 0: Toshiba Satellite 1800 (GP data pin select)
2294 1: Fast pin select (default)
2298 [KNL] Should the soft-lockup detector generate panics.
2300 sonypi.*= [HW] Sony Programmable I/O Control Device driver
2301 See Documentation/sonypi.txt
2303 specialix= [HW,SERIAL] Specialix multi-serial port adapter
2304 See Documentation/serial/specialix.txt.
2306 spia_io_base= [HW,MTD]
2312 Enabled the stack tracer on boot up.
2316 Set the STI (builtin display/keyboard on the HP-PARISC
2317 machines) console (graphic card) which should be used
2318 as the initial boot-console.
2319 See also comment in drivers/video/console/sticore.c.
2322 See comment in drivers/video/console/sticore.c.
2325 Format: bpp:<bpp1>[:<bpp2>[:<bpp3>...]]
2327 sunrpc.min_resvport=
2328 sunrpc.max_resvport=
2330 SunRPC servers often require that client requests
2331 originate from a privileged port (i.e. a port in the
2332 range 0 < portnr < 1024).
2333 An administrator who wishes to reserve some of these
2334 ports for other uses may adjust the range that the
2335 kernel's sunrpc client considers to be privileged
2336 using these two parameters to set the minimum and
2337 maximum port values.
2341 Control how the NFS server code allocates CPUs to
2342 service thread pools. Depending on how many NICs
2343 you have and where their interrupts are bound, this
2344 option will affect which CPUs will do NFS serving.
2345 Note: this parameter cannot be changed while the
2346 NFS server is running.
2348 auto the server chooses an appropriate mode
2349 automatically using heuristics
2350 global a single global pool contains all CPUs
2351 percpu one pool for each CPU
2352 pernode one pool for each NUMA node (equivalent
2353 to global on non-NUMA machines)
2355 sunrpc.tcp_slot_table_entries=
2356 sunrpc.udp_slot_table_entries=
2358 Sets the upper limit on the number of simultaneous
2359 RPC calls that can be sent from the client to a
2360 server. Increasing these values may allow you to
2361 improve throughput, but will also increase the
2362 amount of memory reserved for use by the client.
2364 swiotlb= [IA-64] Number of I/O TLB slabs
2368 sysrq_always_enabled
2370 Ignore sysrq setting - this boot parameter will
2371 neutralize any effect of /proc/sys/kernel/sysrq.
2372 Useful for debugging.
2376 test_suspend= [SUSPEND]
2377 Specify "mem" (for Suspend-to-RAM) or "standby" (for
2378 standby suspend) as the system sleep state to briefly
2379 enter during system startup. The system is woken from
2380 this state using a wakeup-capable RTC alarm.
2382 thash_entries= [KNL,NET]
2383 Set number of hash buckets for TCP connection
2385 thermal.act= [HW,ACPI]
2386 -1: disable all active trip points in all thermal zones
2387 <degrees C>: override all lowest active trip points
2389 thermal.crt= [HW,ACPI]
2390 -1: disable all critical trip points in all thermal zones
2391 <degrees C>: override all critical trip points
2393 thermal.nocrt= [HW,ACPI]
2394 Set to disable actions on ACPI thermal zone
2395 critical and hot trip points.
2397 thermal.off= [HW,ACPI]
2398 1: disable ACPI thermal control
2400 thermal.psv= [HW,ACPI]
2401 -1: disable all passive trip points
2402 <degrees C>: override all passive trip points to this
2405 thermal.tzp= [HW,ACPI]
2406 Specify global default ACPI thermal zone polling rate
2407 <deci-seconds>: poll all this frequency
2408 0: no polling (default)
2412 Specify if the kernel should make use of the cpu
2413 topology informations if the hardware supports these.
2414 The scheduler will make use of these informations and
2415 e.g. base its process migration decisions on it.
2420 tpm_suspend_pcr=[HW,TPM]
2421 Format: integer pcr id
2422 Specify that at suspend time, the tpm driver
2423 should extend the specified pcr with zeros,
2424 as a workaround for some chips which fail to
2425 flush the last written pcr on TPM_SaveState.
2426 This will guarantee that all the other pcrs
2429 trace_buf_size=nn[KMG]
2430 [FTRACE] will set tracing buffer size.
2432 trace_event=[event-list]
2433 [FTRACE] Set and start specified trace events in order
2434 to facilitate early boot debugging.
2435 See also Documentation/trace/events.txt
2437 tsc= Disable clocksource-must-verify flag for TSC.
2439 [x86] reliable: mark tsc clocksource as reliable, this
2440 disables clocksource verification at runtime.
2441 Used to enable high-resolution timer mode on older
2442 hardware, and in virtualized environment.
2444 turbografx.map[2|3]= [HW,JOY]
2445 TurboGraFX parallel port interface
2447 <port#>,<js1>,<js2>,<js3>,<js4>,<js5>,<js6>,<js7>
2448 See also Documentation/input/joystick-parport.txt
2450 uhash_entries= [KNL,NET]
2451 Set number of hash buckets for UDP/UDP-Lite connections
2454 [USB] Ignore overcurrent events (default N).
2455 Some badly-designed motherboards generate lots of
2456 bogus events, for ports that aren't wired to
2457 anything. Set this parameter to avoid log spamming.
2458 Note that genuine overcurrent events won't be
2463 Set unknown_nmi_panic=1 early on boot.
2465 usbcore.autosuspend=
2466 [USB] The autosuspend time delay (in seconds) used
2467 for newly-detected USB devices (default 2). This
2468 is the time required before an idle device will be
2469 autosuspended. Devices for which the delay is set
2470 to a negative value won't be autosuspended at all.
2472 usbcore.usbfs_snoop=
2473 [USB] Set to log all usbfs traffic (default 0 = off).
2475 usbcore.blinkenlights=
2476 [USB] Set to cycle leds on hubs (default 0 = off).
2478 usbcore.old_scheme_first=
2479 [USB] Start with the old device initialization
2480 scheme (default 0 = off).
2482 usbcore.use_both_schemes=
2483 [USB] Try the other device initialization scheme
2484 if the first one fails (default 1 = enabled).
2486 usbcore.initial_descriptor_timeout=
2487 [USB] Specifies timeout for the initial 64-byte
2488 USB_REQ_GET_DESCRIPTOR request in milliseconds
2489 (default 5000 = 5.0 seconds).
2492 [USBHID] The interval which mice are to be polled at.
2494 usb-storage.delay_use=
2495 [UMS] The delay in seconds before a new device is
2496 scanned for Logical Units (default 5).
2499 [UMS] A list of quirks entries to supplement or
2500 override the built-in unusual_devs list. List
2501 entries are separated by commas. Each entry has
2502 the form VID:PID:Flags where VID and PID are Vendor
2503 and Product ID values (4-digit hex numbers) and
2504 Flags is a set of characters, each corresponding
2505 to a common usb-storage quirk flag as follows:
2506 a = SANE_SENSE (collect more than 18 bytes
2508 b = BAD_SENSE (don't collect more than 18
2509 bytes of sense data);
2510 c = FIX_CAPACITY (decrease the reported
2511 device capacity by one sector);
2512 h = CAPACITY_HEURISTICS (decrease the
2513 reported device capacity by one
2514 sector if the number is odd);
2515 i = IGNORE_DEVICE (don't bind to this
2517 l = NOT_LOCKABLE (don't try to lock and
2518 unlock ejectable media);
2519 m = MAX_SECTORS_64 (don't transfer more
2520 than 64 sectors = 32 KB at a time);
2521 o = CAPACITY_OK (accept the capacity
2522 reported by the device);
2523 r = IGNORE_RESIDUE (the device reports
2524 bogus residue values);
2525 s = SINGLE_LUN (the device has only one
2527 w = NO_WP_DETECT (don't test whether the
2528 medium is write-protected).
2529 Example: quirks=0419:aaf5:rl,0421:0433:rc
2532 [X86] Flags controlling user PTE allocations.
2534 nohigh = do not allocate PTE pages in
2535 HIGHMEM regardless of setting
2539 vdso=2: enable compat VDSO (default with COMPAT_VDSO)
2540 vdso=1: enable VDSO (default)
2541 vdso=0: disable VDSO mapping
2544 vdso32=2: enable compat VDSO (default with COMPAT_VDSO)
2545 vdso32=1: enable 32-bit VDSO (default)
2546 vdso32=0: disable 32-bit VDSO mapping
2549 vector=percpu: enable percpu vector domain
2551 video= [FB] Frame buffer configuration
2552 See Documentation/fb/modedb.txt.
2554 vga= [BOOT,X86-32] Select a particular video mode
2555 See Documentation/x86/boot.txt and
2556 Documentation/svga.txt.
2557 Use vga=ask for menu.
2558 This is actually a boot loader parameter; the value is
2559 passed to the kernel using a special protocol.
2561 vmalloc=nn[KMG] [KNL,BOOT] Forces the vmalloc area to have an exact
2562 size of <nn>. This can be used to increase the
2563 minimum size (128MB on x86). It can also be used to
2564 decrease the size and leave more room for directly
2567 vmhalt= [KNL,S390] Perform z/VM CP command after system halt.
2570 vmpanic= [KNL,S390] Perform z/VM CP command after kernel panic.
2573 vmpoff= [KNL,S390] Perform z/VM CP command after power off.
2576 vt.cur_default= [VT] Default cursor shape.
2577 Format: 0xCCBBAA, where AA, BB, and CC are the same as
2578 the parameters of the <Esc>[?A;B;Cc escape sequence;
2579 see VGA-softcursor.txt. Default: 2 = underline.
2581 vt.default_blu= [VT]
2582 Format: <blue0>,<blue1>,<blue2>,...,<blue15>
2583 Change the default blue palette of the console.
2584 This is a 16-member array composed of values
2587 vt.default_grn= [VT]
2588 Format: <green0>,<green1>,<green2>,...,<green15>
2589 Change the default green palette of the console.
2590 This is a 16-member array composed of values
2593 vt.default_red= [VT]
2594 Format: <red0>,<red1>,<red2>,...,<red15>
2595 Change the default red palette of the console.
2596 This is a 16-member array composed of values
2602 Set system-wide default UTF-8 mode for all tty's.
2603 Default is 1, i.e. UTF-8 mode is enabled for all
2604 newly opened terminals.
2606 vt.global_cursor_default=
2609 Set system-wide default for whether a cursor
2610 is shown on new VTs. Default is -1,
2611 i.e. cursors will be created by default unless
2612 overridden by individual drivers. 0 will hide
2613 cursors, 1 will display them.
2615 watchdog timers [HW,WDT] For information on watchdog timers,
2616 see Documentation/watchdog/watchdog-parameters.txt
2617 or other driver-specific files in the
2618 Documentation/watchdog/ directory.
2620 x2apic_phys [X86-64,APIC] Use x2apic physical mode instead of
2621 default x2apic cluster mode on platforms
2624 x86_mrst_timer= [X86-32,APBT]
2625 Choose timer option for x86 Moorestown MID platform.
2626 Two valid options are apbt timer only and lapic timer
2627 plus one apbt timer for broadcast timer.
2628 x86_mrst_timer=apbt_only | lapic_and_apbt
2630 xd= [HW,XT] Original XT pre-IDE (RLL encoded) disks.
2631 xd_geo= See header of drivers/block/xd.c.
2633 xen_emul_unplug= [HW,X86,XEN]
2634 Unplug Xen emulated devices
2635 Format: [unplug0,][unplug1]
2636 ide-disks -- unplug primary master IDE devices
2637 aux-ide-disks -- unplug non-primary-master IDE devices
2638 nics -- unplug network devices
2639 all -- unplug all emulated devices (NICs and IDE disks)
2640 unnecessary -- unplugging emulated devices is
2641 unnecessary even if the host did not respond to
2643 never -- do not unplug even if version check succeeds
2645 xirc2ps_cs= [NET,PCMCIA]
2647 <irq>,<irq_mask>,<io>,<full_duplex>,<do_sound>,<lockup_hack>[,<irq2>[,<irq3>[,<irq4>]]]
2649 ______________________________________________________________________
2653 Add more DRM drivers.
git.openpandora.org / pandora-kernel.git / blob