Bluetooth: Fix SSP acceptor just-works confirmation without MITM commit ba15a58b179ed76a7e887177f2b06de12c58ec8f upstream. From the Bluetooth Core Specification 4.1 page 1958: "if both devices have set the Authentication_Requirements parameter to one of the MITM Protection Not Required options, authentication stage 1 shall function as if both devices set their IO capabilities to DisplayOnly (e.g., Numeric comparison with automatic confirmation on both devices)" So far our implementation has done user confirmation for all just-works cases regardless of the MITM requirements, however following the specification to the word means that we should not be doing confirmation when neither side has the MITM flag set. Signed-off-by: Johan Hedberg <johan.hedberg@intel.com> Tested-by: Szymon Janc <szymon.janc@tieto.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org> [bwh: Backported to 3.2: s/conn->flags/conn->pend/] Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Bluetooth: Fix sending HCI commands after reset commit dbccd791a3fbbdac12c33834b73beff3984988e9 upstream. After sending reset command wait for its command complete event before sending next command. Some chips sends CC event for command received before reset if reset was send before chip replied with CC. This is also required by specification that host shall not send additional HCI commands before receiving CC for reset. < HCI Command: Reset (0x03|0x0003) plen 0 [hci0] 18.404612 > HCI Event: Command Complete (0x0e) plen 4 [hci0] 18.405850 Write Extended Inquiry Response (0x03|0x0052) ncmd 1 Status: Success (0x00) < HCI Command: Read Local Supported Features (0x04|0x0003) plen 0 [hci0] 18.406079 > HCI Event: Command Complete (0x0e) plen 4 [hci0] 18.407864 Reset (0x03|0x0003) ncmd 1 Status: Success (0x00) < HCI Command: Read Local Supported Features (0x04|0x0003) plen 0 [hci0] 18.408062 > HCI Event: Command Complete (0x0e) plen 12 [hci0] 18.408835 Signed-off-by: Szymon Janc <szymon.janc@tieto.com> Acked-by: Johan Hedberg <johan.hedberg@intel.com> Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk> Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Bluetooth: Fix legacy pairing with some devices commit a9ea3ed9b71cc3271dd59e76f65748adcaa76422 upstream. Some devices e.g. some Android based phones don't do SDP search before pairing and cancel legacy pairing when ACL is disconnected. PIN Code Request event which changes ACL timeout to HCI_PAIRING_TIMEOUT is only received after remote user entered PIN. In that case no L2CAP is connected so default HCI_DISCONN_TIMEOUT (2 seconds) is being used to timeout ACL connection. This results in problems with legacy pairing as remote user has only few seconds to enter PIN before ACL is disconnected. Increase disconnect timeout for incomming connection to HCI_PAIRING_TIMEOUT if SSP is disabled and no linkey exists. To avoid keeping ACL alive for too long after SDP search set ACL timeout back to HCI_DISCONN_TIMEOUT when L2CAP is connected. 2012-07-19 13:24:43.413521 < HCI Command: Create Connection (0x01|0x0005) plen 13 bdaddr 00:02:72:D6:6A:3F ptype 0xcc18 rswitch 0x01 clkoffset 0x0000 Packet type: DM1 DM3 DM5 DH1 DH3 DH5 2012-07-19 13:24:43.425224 > HCI Event: Command Status (0x0f) plen 4 Create Connection (0x01|0x0005) status 0x00 ncmd 1 2012-07-19 13:24:43.885222 > HCI Event: Role Change (0x12) plen 8 status 0x00 bdaddr 00:02:72:D6:6A:3F role 0x01 Role: Slave 2012-07-19 13:24:44.054221 > HCI Event: Connect Complete (0x03) plen 11 status 0x00 handle 42 bdaddr 00:02:72:D6:6A:3F type ACL encrypt 0x00 2012-07-19 13:24:44.054313 < HCI Command: Read Remote Supported Features (0x01|0x001b) plen 2 handle 42 2012-07-19 13:24:44.055176 > HCI Event: Page Scan Repetition Mode Change (0x20) plen 7 bdaddr 00:02:72:D6:6A:3F mode 0 2012-07-19 13:24:44.056217 > HCI Event: Max Slots Change (0x1b) plen 3 handle 42 slots 5 2012-07-19 13:24:44.059218 > HCI Event: Command Status (0x0f) plen 4 Read Remote Supported Features (0x01|0x001b) status 0x00 ncmd 0 2012-07-19 13:24:44.062192 > HCI Event: Command Status (0x0f) plen 4 Unknown (0x00|0x0000) status 0x00 ncmd 1 2012-07-19 13:24:44.067219 > HCI Event: Read Remote Supported Features (0x0b) plen 11 status 0x00 handle 42 Features: 0xbf 0xfe 0xcf 0xfe 0xdb 0xff 0x7b 0x87 2012-07-19 13:24:44.067248 < HCI Command: Read Remote Extended Features (0x01|0x001c) plen 3 handle 42 page 1 2012-07-19 13:24:44.071217 > HCI Event: Command Status (0x0f) plen 4 Read Remote Extended Features (0x01|0x001c) status 0x00 ncmd 1 2012-07-19 13:24:44.076218 > HCI Event: Read Remote Extended Features (0x23) plen 13 status 0x00 handle 42 page 1 max 1 Features: 0x01 0x00 0x00 0x00 0x00 0x00 0x00 0x00 2012-07-19 13:24:44.076249 < HCI Command: Remote Name Request (0x01|0x0019) plen 10 bdaddr 00:02:72:D6:6A:3F mode 2 clkoffset 0x0000 2012-07-19 13:24:44.081218 > HCI Event: Command Status (0x0f) plen 4 Remote Name Request (0x01|0x0019) status 0x00 ncmd 1 2012-07-19 13:24:44.105214 > HCI Event: Remote Name Req Complete (0x07) plen 255 status 0x00 bdaddr 00:02:72:D6:6A:3F name 'uw000951-0' 2012-07-19 13:24:44.105284 < HCI Command: Authentication Requested (0x01|0x0011) plen 2 handle 42 2012-07-19 13:24:44.111207 > HCI Event: Command Status (0x0f) plen 4 Authentication Requested (0x01|0x0011) status 0x00 ncmd 1 2012-07-19 13:24:44.112220 > HCI Event: Link Key Request (0x17) plen 6 bdaddr 00:02:72:D6:6A:3F 2012-07-19 13:24:44.112249 < HCI Command: Link Key Request Negative Reply (0x01|0x000c) plen 6 bdaddr 00:02:72:D6:6A:3F 2012-07-19 13:24:44.115215 > HCI Event: Command Complete (0x0e) plen 10 Link Key Request Negative Reply (0x01|0x000c) ncmd 1 status 0x00 bdaddr 00:02:72:D6:6A:3F 2012-07-19 13:24:44.116215 > HCI Event: PIN Code Request (0x16) plen 6 bdaddr 00:02:72:D6:6A:3F 2012-07-19 13:24:48.099184 > HCI Event: Auth Complete (0x06) plen 3 status 0x13 handle 42 Error: Remote User Terminated Connection 2012-07-19 13:24:48.179182 > HCI Event: Disconn Complete (0x05) plen 4 status 0x00 handle 42 reason 0x13 Reason: Remote User Terminated Connection Signed-off-by: Szymon Janc <szymon.janc@tieto.com> Acked-by: Johan Hedberg <johan.hedberg@intel.com> Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk> [bwh: Backported to 3.2: - Adjust context - hci_conn_ssp_enabled() is not defined; open-code the condition] Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Bluetooth: Correct version check in hci_setup Check for hci_ver instead of lmp_ver Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com> Acked-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
Bluetooth: hci_le_adv_report_evt code refactoring There is no reason to treat the first advertising entry differently from the potential other ones. Besides, the current implementation can easily leads to typos. Signed-off-by: Andre Guedes <andre.guedes@openbossa.org> Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
Bluetooth: Fix possible NULL pointer dereference Checking conn->pending_sec_level if there is no connection leads to potential null pointer dereference. Don't process pin_code_request_event at all if no connection exists. Signed-off-by: Waldemar Rymarkiewicz <waldemar.rymarkiewicz@gmail.com> Acked-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
Bluetooth: Reduce critical region. This patch reduces the critial region (protected by hdev->lock) in hci_cc_le_set_scan_enable(). This way, only really required code is synchronized. Signed-off-by: Andre Guedes <andre.guedes@openbossa.org> Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
Bluetooth: Require authentication if MITM protection is requested The HIGH security level requires a 16 digit pin code for non-SSP bondings. Sometimes this requirement is not acceptable and we still want protection againts MITM attacks (which is something that the MEDIUM security level doesn't provide), for that we should allow another way to request authentication without using the HIGH security level. Signed-off-by: Vinicius Costa Gomes <vinicius.gomes@openbossa.org> Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
Bluetooth: Add link_type information to the mgmt Connected event One piece of information that was lost when using the mgmt interface, was the type of the connection. Using HCI events we used to know the type of the connection based on the type of the event, e.g. HCI_LE_Connection_Complete for LE links. Signed-off-by: Vinicius Costa Gomes <vinicius.gomes@openbossa.org> Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
Bluetooth: Fix timeout on scanning for the second time The checks for HCI_INQUIRY and HCI_MGMT were in the wrong order, so that second scans always failed. Signed-off-by: Oliver Neukum <oneukum@suse.de> Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
Bluetooth: Add support for storing the key size In some cases it will be useful having the key size used for encrypting the link. For example, some profiles may restrict some operations depending on the key length. The key size is stored in the key that is passed to userspace using the pin_length field in the key structure. For now this field is only valid for LE controllers. 3.0+HS controllers define the Read Encryption Key Size command, this field is intended for storing the value returned by that command. Signed-off-by: Vinicius Costa Gomes <vinicius.gomes@openbossa.org> Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
Bluetooth: Reject an encryption request when the key isn't found Now that we have methods to finding keys by its parameters we can reject an encryption request if the key isn't found. Signed-off-by: Vinicius Costa Gomes <vinicius.gomes@openbossa.org> Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
Bluetooth: Add enable_le module parameter This patch adds a new module parameter to enable/disable host LE support. By default host LE support is disabled. Signed-off-by: Andre Guedes <andre.guedes@openbossa.org> Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
Bluetooth: Write LE Host Supported command This patch adds a handler to Write LE Host Supported command complete events. Once this commands has completed successfully, we should read the extended LMP features and update the extfeatures field in hci_dev. Signed-off-by: Andre Guedes <andre.guedes@openbossa.org> Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
Bluetooth: Add extfeatures to struct hci_dev This new field holds the extended LMP features value. Some LE mechanism such as discovery procedure needs to read the extended LMP features to work properly. Signed-off-by: Andre Guedes <andre.guedes@openbossa.org> Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
Bluetooth: Add support for Pairing features exchange This patch implements a simple version of the SMP Pairing Features exchange procedure (Vol. 3 Part H, Section 2.3.5.1). For now, everything that would cause a Pairing Method different of Just Works to be chosen is rejected. Signed-off-by: Vinicius Costa Gomes <vinicius.gomes@openbossa.org> Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
Bluetooth: Fix initial security level of LE links As the default security level (BT_SECURITY_SDP) doesn't make sense for LE links, initialize LE links with something that makes sense. Signed-off-by: Vinicius Costa Gomes <vinicius.gomes@openbossa.org> Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
Bluetooth: Add support for LE Start Encryption This adds support for starting SMP Phase 2 Encryption, when the initial SMP negotiation is successful. This adds the LE Start Encryption and LE Long Term Key Request commands and related events. Signed-off-by: Vinicius Costa Gomes <vinicius.gomes@openbossa.org> Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
Merge /linux/kernel/git/padovan/bluetooth-2.6 Conflicts: net/bluetooth/rfcomm/sock.c
Bluetooth: Do not send SET_EVENT_MASK for 1.1 and earlier devices Some old hci controllers do not accept any mask so leave the default mask on for these devices. < HCI Command: Set Event Mask (0x03|0x0001) plen 8 Mask: 0xfffffbff00000000 > HCI Event: Command Complete (0x0e) plen 4 Set Event Mask (0x03|0x0001) ncmd 1 status 0x12 Error: Invalid HCI Command Parameters Signed-off-by: Ville Tervo <ville.tervo@nokia.com> Tested-by: Corey Boyle <corey@kansanian.com> Tested-by: Ed Tomlinson <edt@aei.ca> Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>