X-Git-Url: https://git.openpandora.org/cgi-bin/gitweb.cgi?a=blobdiff_plain;f=Documentation%2Fhwmon%2Fabituguru-datasheet;h=8d2be8a0b1e38c146a80130d8d96d94ce6025516;hb=26cf445721763d61b08ce394f8bdbd4c5610b563;hp=4d184f2db0ea668e0ce6440693a61b28c202f98d;hpb=7c7758f99d39d529a64d4f60d22129bbf2f16d74;p=pandora-kernel.git diff --git a/Documentation/hwmon/abituguru-datasheet b/Documentation/hwmon/abituguru-datasheet index 4d184f2db0ea..8d2be8a0b1e3 100644 --- a/Documentation/hwmon/abituguru-datasheet +++ b/Documentation/hwmon/abituguru-datasheet @@ -5,9 +5,9 @@ First of all, what I know about uGuru is no fact based on any help, hints or datasheet from Abit. The data I have got on uGuru have I assembled through my weak knowledge in "backwards engineering". And just for the record, you may have noticed uGuru isn't a chip developed by -Abit, as they claim it to be. It's realy just an microprocessor (uC) created by +Abit, as they claim it to be. It's really just an microprocessor (uC) created by Winbond (W83L950D). And no, reading the manual for this specific uC or -mailing Windbond for help won't give any usefull data about uGuru, as it is +mailing Windbond for help won't give any useful data about uGuru, as it is the program inside the uC that is responding to calls. Olle Sandberg , 2005-05-25 @@ -41,7 +41,7 @@ later on attached again data-port will hold 0x08, more about this later. After wider testing of the Linux kernel driver some variants of the uGuru have turned up which will hold 0x00 instead of 0xAC at the CMD port, thus we also -have to test CMD for two different values. On these uGuru's DATA will initally +have to test CMD for two different values. On these uGuru's DATA will initially hold 0x09 and will only hold 0x08 after reading CMD first, so CMD must be read first! @@ -121,7 +121,7 @@ Once all bytes have been read data will hold 0x09, but there is no reason to test for this. Notice that the number of bytes is bank address dependent see above and below. -After completing a successfull read it is advised to put the uGuru back in +After completing a successful read it is advised to put the uGuru back in ready mode, so that it is ready for the next read / write cycle. This way if your program / driver is unloaded and later loaded again the detection algorithm described above will still work. @@ -141,7 +141,7 @@ don't ask why this is the way it is. Once DATA holds 0x01 read CMD it should hold 0xAC now. -After completing a successfull write it is advised to put the uGuru back in +After completing a successful write it is advised to put the uGuru back in ready mode, so that it is ready for the next read / write cycle. This way if your program / driver is unloaded and later loaded again the detection algorithm described above will still work. @@ -308,5 +308,5 @@ the voltage / clock programming out, I tried reading and only reading banks resulted in a _permanent_ reprogramming of the voltages, luckily I had the sensors part configured so that it would shutdown my system on any out of spec voltages which proprably safed my computer (after a reboot I managed to -immediatly enter the bios and reload the defaults). This probably means that +immediately enter the bios and reload the defaults). This probably means that the read/write cycle for the non sensor part is different from the sensor part.