#ifndef _ZD_CHIP_H
#define _ZD_CHIP_H
-#include "zd_types.h"
#include "zd_rf.h"
#include "zd_usb.h"
* adds a processor for handling the USB protocol.
*/
+/* Address space */
+enum {
+ /* CONTROL REGISTERS */
+ CR_START = 0x9000,
+
+
+ /* FIRMWARE */
+ FW_START = 0xee00,
+
+
+ /* EEPROM */
+ E2P_START = 0xf800,
+ E2P_LEN = 0x800,
+
+ /* EEPROM layout */
+ E2P_LOAD_CODE_LEN = 0xe, /* base 0xf800 */
+ E2P_LOAD_VECT_LEN = 0x9, /* base 0xf80e */
+ /* E2P_DATA indexes into this */
+ E2P_DATA_LEN = 0x7e, /* base 0xf817 */
+ E2P_BOOT_CODE_LEN = 0x760, /* base 0xf895 */
+ E2P_INTR_VECT_LEN = 0xb, /* base 0xfff5 */
+
+ /* Some precomputed offsets into the EEPROM */
+ E2P_DATA_OFFSET = E2P_LOAD_CODE_LEN + E2P_LOAD_VECT_LEN,
+ E2P_BOOT_CODE_OFFSET = E2P_DATA_OFFSET + E2P_DATA_LEN,
+};
+
+#define CTL_REG(offset) ((zd_addr_t)(CR_START + (offset)))
+#define E2P_DATA(offset) ((zd_addr_t)(E2P_START + E2P_DATA_OFFSET + (offset)))
+#define FWRAW_DATA(offset) ((zd_addr_t)(FW_START + (offset)))
+
/* 8-bit hardware registers */
#define CR0 CTL_REG(0x0000)
#define CR1 CTL_REG(0x0004)
#define CR_MAX_PHY_REG 255
-/* Taken from the ZYDAS driver, not all of them are relevant for the ZSD1211
+/* Taken from the ZYDAS driver, not all of them are relevant for the ZD1211
* driver.
*/
#define CR_MAC_PS_STATE CTL_REG(0x050C)
#define CR_INTERRUPT CTL_REG(0x0510)
-#define INT_TX_COMPLETE 0x00000001
-#define INT_RX_COMPLETE 0x00000002
-#define INT_RETRY_FAIL 0x00000004
-#define INT_WAKEUP 0x00000008
-#define INT_DTIM_NOTIFY 0x00000020
-#define INT_CFG_NEXT_BCN 0x00000040
-#define INT_BUS_ABORT 0x00000080
-#define INT_TX_FIFO_READY 0x00000100
-#define INT_UART 0x00000200
-#define INT_TX_COMPLETE_EN 0x00010000
-#define INT_RX_COMPLETE_EN 0x00020000
-#define INT_RETRY_FAIL_EN 0x00040000
-#define INT_WAKEUP_EN 0x00080000
-#define INT_DTIM_NOTIFY_EN 0x00200000
-#define INT_CFG_NEXT_BCN_EN 0x00400000
-#define INT_BUS_ABORT_EN 0x00800000
-#define INT_TX_FIFO_READY_EN 0x01000000
-#define INT_UART_EN 0x02000000
+#define INT_TX_COMPLETE (1 << 0)
+#define INT_RX_COMPLETE (1 << 1)
+#define INT_RETRY_FAIL (1 << 2)
+#define INT_WAKEUP (1 << 3)
+#define INT_DTIM_NOTIFY (1 << 5)
+#define INT_CFG_NEXT_BCN (1 << 6)
+#define INT_BUS_ABORT (1 << 7)
+#define INT_TX_FIFO_READY (1 << 8)
+#define INT_UART (1 << 9)
+#define INT_TX_COMPLETE_EN (1 << 16)
+#define INT_RX_COMPLETE_EN (1 << 17)
+#define INT_RETRY_FAIL_EN (1 << 18)
+#define INT_WAKEUP_EN (1 << 19)
+#define INT_DTIM_NOTIFY_EN (1 << 21)
+#define INT_CFG_NEXT_BCN_EN (1 << 22)
+#define INT_BUS_ABORT_EN (1 << 23)
+#define INT_TX_FIFO_READY_EN (1 << 24)
+#define INT_UART_EN (1 << 25)
#define CR_TSF_LOW_PART CTL_REG(0x0514)
#define CR_TSF_HIGH_PART CTL_REG(0x0518)
#define CR_BSSID_P1 CTL_REG(0x0618)
#define CR_BSSID_P2 CTL_REG(0x061C)
#define CR_BCN_PLCP_CFG CTL_REG(0x0620)
+
+/* Group hash table for filtering incoming packets.
+ *
+ * The group hash table is 64 bit large and split over two parts. The first
+ * part is the lower part. The upper 6 bits of the last byte of the target
+ * address are used as index. Packets are received if the hash table bit is
+ * set. This is used for multicast handling, but for broadcasts (address
+ * ff:ff:ff:ff:ff:ff) the highest bit in the second table must also be set.
+ */
#define CR_GROUP_HASH_P1 CTL_REG(0x0624)
#define CR_GROUP_HASH_P2 CTL_REG(0x0628)
-#define CR_RX_TIMEOUT CTL_REG(0x062C)
+#define CR_RX_TIMEOUT CTL_REG(0x062C)
/* Basic rates supported by the BSS. When producing ACK or CTS messages, the
* device will use a rate in this table that is less than or equal to the rate
* of the incoming frame which prompted the response */
#define CR_BASIC_RATE_TBL CTL_REG(0x0630)
-#define CR_RATE_1M 0x0001 /* 802.11b */
-#define CR_RATE_2M 0x0002 /* 802.11b */
-#define CR_RATE_5_5M 0x0004 /* 802.11b */
-#define CR_RATE_11M 0x0008 /* 802.11b */
-#define CR_RATE_6M 0x0100 /* 802.11g */
-#define CR_RATE_9M 0x0200 /* 802.11g */
-#define CR_RATE_12M 0x0400 /* 802.11g */
-#define CR_RATE_18M 0x0800 /* 802.11g */
-#define CR_RATE_24M 0x1000 /* 802.11g */
-#define CR_RATE_36M 0x2000 /* 802.11g */
-#define CR_RATE_48M 0x4000 /* 802.11g */
-#define CR_RATE_54M 0x8000 /* 802.11g */
+#define CR_RATE_1M (1 << 0) /* 802.11b */
+#define CR_RATE_2M (1 << 1) /* 802.11b */
+#define CR_RATE_5_5M (1 << 2) /* 802.11b */
+#define CR_RATE_11M (1 << 3) /* 802.11b */
+#define CR_RATE_6M (1 << 8) /* 802.11g */
+#define CR_RATE_9M (1 << 9) /* 802.11g */
+#define CR_RATE_12M (1 << 10) /* 802.11g */
+#define CR_RATE_18M (1 << 11) /* 802.11g */
+#define CR_RATE_24M (1 << 12) /* 802.11g */
+#define CR_RATE_36M (1 << 13) /* 802.11g */
+#define CR_RATE_48M (1 << 14) /* 802.11g */
+#define CR_RATE_54M (1 << 15) /* 802.11g */
#define CR_RATES_80211G 0xff00
#define CR_RATES_80211B 0x000f
#define CR_MANDATORY_RATE_TBL CTL_REG(0x0634)
#define CR_RTS_CTS_RATE CTL_REG(0x0638)
+/* These are all bit indexes in CR_RTS_CTS_RATE, so remember to shift. */
+#define RTSCTS_SH_RTS_RATE 0
+#define RTSCTS_SH_EXP_CTS_RATE 4
+#define RTSCTS_SH_RTS_MOD_TYPE 8
+#define RTSCTS_SH_RTS_PMB_TYPE 9
+#define RTSCTS_SH_CTS_RATE 16
+#define RTSCTS_SH_CTS_MOD_TYPE 24
+#define RTSCTS_SH_CTS_PMB_TYPE 25
+
#define CR_WEP_PROTECT CTL_REG(0x063C)
#define CR_RX_THRESHOLD CTL_REG(0x0640)
/* register for controlling the LEDS */
#define CR_LED CTL_REG(0x0644)
/* masks for controlling LEDs */
-#define LED1 0x0100
-#define LED2 0x0200
+#define LED1 (1 << 8)
+#define LED2 (1 << 9)
+#define LED_SW (1 << 10)
/* Seems to indicate that the configuration is over.
*/
* registers, so one could argue it is a LOCK bit. But calling it
* LOCK_PHY_REGS makes it confusing.
*/
-#define UNLOCK_PHY_REGS 0x0080
+#define UNLOCK_PHY_REGS (1 << 7)
#define CR_DEVICE_STATE CTL_REG(0x0684)
#define CR_UNDERRUN_CNT CTL_REG(0x0688)
#define CR_RX_FILTER CTL_REG(0x068c)
-#define RX_FILTER_ASSOC_RESPONSE 0x0002
-#define RX_FILTER_REASSOC_RESPONSE 0x0008
-#define RX_FILTER_PROBE_RESPONSE 0x0020
-#define RX_FILTER_BEACON 0x0100
-#define RX_FILTER_DISASSOC 0x0400
-#define RX_FILTER_AUTH 0x0800
+#define RX_FILTER_ASSOC_RESPONSE (1 << 1)
+#define RX_FILTER_REASSOC_RESPONSE (1 << 3)
+#define RX_FILTER_PROBE_RESPONSE (1 << 5)
+#define RX_FILTER_BEACON (1 << 8)
+#define RX_FILTER_DISASSOC (1 << 10)
+#define RX_FILTER_AUTH (1 << 11)
#define AP_RX_FILTER 0x0400feff
#define STA_RX_FILTER 0x0000ffff
/*
* Upper 16 bit contains the regulatory domain.
*/
-#define E2P_SUBID E2P_REG(0x00)
-#define E2P_POD E2P_REG(0x02)
-#define E2P_MAC_ADDR_P1 E2P_REG(0x04)
-#define E2P_MAC_ADDR_P2 E2P_REG(0x06)
-#define E2P_PWR_CAL_VALUE1 E2P_REG(0x08)
-#define E2P_PWR_CAL_VALUE2 E2P_REG(0x0a)
-#define E2P_PWR_CAL_VALUE3 E2P_REG(0x0c)
-#define E2P_PWR_CAL_VALUE4 E2P_REG(0x0e)
-#define E2P_PWR_INT_VALUE1 E2P_REG(0x10)
-#define E2P_PWR_INT_VALUE2 E2P_REG(0x12)
-#define E2P_PWR_INT_VALUE3 E2P_REG(0x14)
-#define E2P_PWR_INT_VALUE4 E2P_REG(0x16)
+#define E2P_SUBID E2P_DATA(0x00)
+#define E2P_POD E2P_DATA(0x02)
+#define E2P_MAC_ADDR_P1 E2P_DATA(0x04)
+#define E2P_MAC_ADDR_P2 E2P_DATA(0x06)
+#define E2P_PWR_CAL_VALUE1 E2P_DATA(0x08)
+#define E2P_PWR_CAL_VALUE2 E2P_DATA(0x0a)
+#define E2P_PWR_CAL_VALUE3 E2P_DATA(0x0c)
+#define E2P_PWR_CAL_VALUE4 E2P_DATA(0x0e)
+#define E2P_PWR_INT_VALUE1 E2P_DATA(0x10)
+#define E2P_PWR_INT_VALUE2 E2P_DATA(0x12)
+#define E2P_PWR_INT_VALUE3 E2P_DATA(0x14)
+#define E2P_PWR_INT_VALUE4 E2P_DATA(0x16)
/* Contains a bit for each allowed channel. It gives for Europe (ETSI 0x30)
* also only 11 channels. */
-#define E2P_ALLOWED_CHANNEL E2P_REG(0x18)
-
-#define E2P_PHY_REG E2P_REG(0x1a)
-#define E2P_DEVICE_VER E2P_REG(0x20)
-#define E2P_36M_CAL_VALUE1 E2P_REG(0x28)
-#define E2P_36M_CAL_VALUE2 E2P_REG(0x2a)
-#define E2P_36M_CAL_VALUE3 E2P_REG(0x2c)
-#define E2P_36M_CAL_VALUE4 E2P_REG(0x2e)
-#define E2P_11A_INT_VALUE1 E2P_REG(0x30)
-#define E2P_11A_INT_VALUE2 E2P_REG(0x32)
-#define E2P_11A_INT_VALUE3 E2P_REG(0x34)
-#define E2P_11A_INT_VALUE4 E2P_REG(0x36)
-#define E2P_48M_CAL_VALUE1 E2P_REG(0x38)
-#define E2P_48M_CAL_VALUE2 E2P_REG(0x3a)
-#define E2P_48M_CAL_VALUE3 E2P_REG(0x3c)
-#define E2P_48M_CAL_VALUE4 E2P_REG(0x3e)
-#define E2P_48M_INT_VALUE1 E2P_REG(0x40)
-#define E2P_48M_INT_VALUE2 E2P_REG(0x42)
-#define E2P_48M_INT_VALUE3 E2P_REG(0x44)
-#define E2P_48M_INT_VALUE4 E2P_REG(0x46)
-#define E2P_54M_CAL_VALUE1 E2P_REG(0x48) /* ??? */
-#define E2P_54M_CAL_VALUE2 E2P_REG(0x4a)
-#define E2P_54M_CAL_VALUE3 E2P_REG(0x4c)
-#define E2P_54M_CAL_VALUE4 E2P_REG(0x4e)
-#define E2P_54M_INT_VALUE1 E2P_REG(0x50)
-#define E2P_54M_INT_VALUE2 E2P_REG(0x52)
-#define E2P_54M_INT_VALUE3 E2P_REG(0x54)
-#define E2P_54M_INT_VALUE4 E2P_REG(0x56)
-
-/* All 16 bit values */
-#define FW_FIRMWARE_VER FW_REG(0)
-/* non-zero if USB high speed connection */
-#define FW_USB_SPEED FW_REG(1)
-#define FW_FIX_TX_RATE FW_REG(2)
-/* Seems to be able to control LEDs over the firmware */
-#define FW_LINK_STATUS FW_REG(3)
-#define FW_SOFT_RESET FW_REG(4)
-#define FW_FLASH_CHK FW_REG(5)
-
+#define E2P_ALLOWED_CHANNEL E2P_DATA(0x18)
+
+#define E2P_PHY_REG E2P_DATA(0x1a)
+#define E2P_DEVICE_VER E2P_DATA(0x20)
+#define E2P_36M_CAL_VALUE1 E2P_DATA(0x28)
+#define E2P_36M_CAL_VALUE2 E2P_DATA(0x2a)
+#define E2P_36M_CAL_VALUE3 E2P_DATA(0x2c)
+#define E2P_36M_CAL_VALUE4 E2P_DATA(0x2e)
+#define E2P_11A_INT_VALUE1 E2P_DATA(0x30)
+#define E2P_11A_INT_VALUE2 E2P_DATA(0x32)
+#define E2P_11A_INT_VALUE3 E2P_DATA(0x34)
+#define E2P_11A_INT_VALUE4 E2P_DATA(0x36)
+#define E2P_48M_CAL_VALUE1 E2P_DATA(0x38)
+#define E2P_48M_CAL_VALUE2 E2P_DATA(0x3a)
+#define E2P_48M_CAL_VALUE3 E2P_DATA(0x3c)
+#define E2P_48M_CAL_VALUE4 E2P_DATA(0x3e)
+#define E2P_48M_INT_VALUE1 E2P_DATA(0x40)
+#define E2P_48M_INT_VALUE2 E2P_DATA(0x42)
+#define E2P_48M_INT_VALUE3 E2P_DATA(0x44)
+#define E2P_48M_INT_VALUE4 E2P_DATA(0x46)
+#define E2P_54M_CAL_VALUE1 E2P_DATA(0x48) /* ??? */
+#define E2P_54M_CAL_VALUE2 E2P_DATA(0x4a)
+#define E2P_54M_CAL_VALUE3 E2P_DATA(0x4c)
+#define E2P_54M_CAL_VALUE4 E2P_DATA(0x4e)
+#define E2P_54M_INT_VALUE1 E2P_DATA(0x50)
+#define E2P_54M_INT_VALUE2 E2P_DATA(0x52)
+#define E2P_54M_INT_VALUE3 E2P_DATA(0x54)
+#define E2P_54M_INT_VALUE4 E2P_DATA(0x56)
+
+/* This word contains the base address of the FW_REG_ registers below */
+#define FWRAW_REGS_ADDR FWRAW_DATA(0x1d)
+
+/* All 16 bit values, offset from the address in FWRAW_REGS_ADDR */
enum {
- CR_BASE_OFFSET = 0x9000,
- FW_START_OFFSET = 0xee00,
- FW_BASE_ADDR_OFFSET = FW_START_OFFSET + 0x1d,
- EEPROM_START_OFFSET = 0xf800,
- EEPROM_SIZE = 0x800, /* words */
- LOAD_CODE_SIZE = 0xe, /* words */
- LOAD_VECT_SIZE = 0x10000 - 0xfff7, /* words */
- EEPROM_REGS_OFFSET = LOAD_CODE_SIZE + LOAD_VECT_SIZE,
- EEPROM_REGS_SIZE = 0x7e, /* words */
- E2P_BASE_OFFSET = EEPROM_START_OFFSET +
- EEPROM_REGS_OFFSET,
+ FW_REG_FIRMWARE_VER = 0,
+ /* non-zero if USB high speed connection */
+ FW_REG_USB_SPEED = 1,
+ FW_REG_FIX_TX_RATE = 2,
+ /* Seems to be able to control LEDs over the firmware */
+ FW_REG_LED_LINK_STATUS = 3,
+ FW_REG_SOFT_RESET = 4,
+ FW_REG_FLASH_CHK = 5,
};
-#define FW_REG_TABLE_ADDR USB_ADDR(FW_START_OFFSET + 0x1d)
+/* Values for FW_LINK_STATUS */
+#define FW_LINK_OFF 0x0
+#define FW_LINK_TX 0x1
+/* 0x2 - link led on? */
enum {
/* indices for ofdm_cal_values */
struct zd_usb usb;
struct zd_rf rf;
struct mutex mutex;
+ /* Base address of FW_REG_ registers */
+ zd_addr_t fw_regs_base;
u8 e2p_mac[ETH_ALEN];
/* EepSetPoint in the vendor driver */
u8 pwr_cal_values[E2P_CHANNEL_COUNT];
u8 pwr_int_values[E2P_CHANNEL_COUNT];
/* SetPointOFDM in the vendor driver */
u8 ofdm_cal_values[3][E2P_CHANNEL_COUNT];
- u8 pa_type:4, patch_cck_gain:1, patch_cr157:1, patch_6m_band_edge:1,
- new_phy_layout:1, is_zd1211b:1;
+ u16 link_led;
+ unsigned int pa_type:4,
+ patch_cck_gain:1, patch_cr157:1, patch_6m_band_edge:1,
+ new_phy_layout:1, al2230s_bit:1,
+ is_zd1211b:1, supports_tx_led:1;
};
static inline struct zd_chip *zd_usb_to_chip(struct zd_usb *usb)
int zd_chip_enable_hwint(struct zd_chip *chip);
int zd_chip_disable_hwint(struct zd_chip *chip);
+int zd_chip_set_rts_cts_rate_locked(struct zd_chip *chip,
+ u8 rts_rate, int preamble);
+
static inline int zd_get_encryption_type(struct zd_chip *chip, u32 *type)
{
return zd_ioread32(chip, CR_ENCRYPTION_TYPE, type);
return zd_ioread16(chip, CR_BASIC_RATE_TBL, cr_rates);
}
-int zd_chip_set_basic_rates(struct zd_chip *chip, u16 cr_rates);
+int zd_chip_set_basic_rates_locked(struct zd_chip *chip, u16 cr_rates);
+
+static inline int zd_chip_set_basic_rates(struct zd_chip *chip, u16 cr_rates)
+{
+ int r;
+
+ mutex_lock(&chip->mutex);
+ r = zd_chip_set_basic_rates_locked(chip, cr_rates);
+ mutex_unlock(&chip->mutex);
+ return r;
+}
static inline int zd_chip_set_rx_filter(struct zd_chip *chip, u32 filter)
{
int zd_chip_unlock_phy_regs(struct zd_chip *chip);
enum led_status {
- LED_OFF = 0,
- LED_ON = 1,
- LED_FLIP = 2,
- LED_STATUS = 3,
+ LED_OFF = 0,
+ LED_SCANNING = 1,
+ LED_ASSOCIATED = 2,
};
-int zd_chip_led_status(struct zd_chip *chip, int led, enum led_status status);
-int zd_chip_led_flip(struct zd_chip *chip, int led,
- const unsigned int *phases_msecs, unsigned int count);
+int zd_chip_control_leds(struct zd_chip *chip, enum led_status status);
int zd_set_beacon_interval(struct zd_chip *chip, u32 interval);
u16 zd_rx_rate(const void *rx_frame, const struct rx_status *status);
+struct zd_mc_hash {
+ u32 low;
+ u32 high;
+};
+
+static inline void zd_mc_clear(struct zd_mc_hash *hash)
+{
+ hash->low = 0;
+ /* The interfaces must always received broadcasts.
+ * The hash of the broadcast address ff:ff:ff:ff:ff:ff is 63.
+ */
+ hash->high = 0x80000000;
+}
+
+static inline void zd_mc_add_all(struct zd_mc_hash *hash)
+{
+ hash->low = hash->high = 0xffffffff;
+}
+
+static inline void zd_mc_add_addr(struct zd_mc_hash *hash, u8 *addr)
+{
+ unsigned int i = addr[5] >> 2;
+ if (i < 32) {
+ hash->low |= 1 << i;
+ } else {
+ hash->high |= 1 << (i-32);
+ }
+}
+
+int zd_chip_set_multicast_hash(struct zd_chip *chip,
+ struct zd_mc_hash *hash);
+
#endif /* _ZD_CHIP_H */