H. Nikolaus Schaller [Wed, 27 Jan 2016 14:12:44 +0000 (15:12 +0100)]
Pyra: disable b2429x watchdog timer or the board will shut down ~30 seconds after U-Boot did start
Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
H. Nikolaus Schaller [Wed, 27 Jan 2016 10:15:40 +0000 (11:15 +0100)]
enable mtest command for OMAP5432EVM
Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
H. Nikolaus Schaller [Mon, 25 Jan 2016 15:13:57 +0000 (16:13 +0100)]
add tca642x commands and enable mtest command
Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
H. Nikolaus Schaller [Mon, 25 Jan 2016 15:13:30 +0000 (16:13 +0100)]
fix config_cmd_tca642x
Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
H. Nikolaus Schaller [Mon, 25 Jan 2016 15:13:03 +0000 (16:13 +0100)]
add paramters for mtest command and run mtest before booting
Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
H. Nikolaus Schaller [Mon, 25 Jan 2016 15:10:47 +0000 (16:10 +0100)]
fix boot directory
Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
H. Nikolaus Schaller [Wed, 20 Jan 2016 14:05:31 +0000 (15:05 +0100)]
LC15: fix for #ifndef structure
Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
H. Nikolaus Schaller [Wed, 20 Jan 2016 11:06:13 +0000 (12:06 +0100)]
Boot Scripts: all boot scripts replaced by uEnv.txt setup
Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
H. Nikolaus Schaller [Wed, 20 Jan 2016 11:05:34 +0000 (12:05 +0100)]
Pyra: take IINLIM code from Linux driver
Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
H. Nikolaus Schaller [Wed, 20 Jan 2016 11:01:57 +0000 (12:01 +0100)]
Fix bootcmd and some initialization in ti_omap5_common so that we don't need a boot.scr any more
Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
H. Nikolaus Schaller [Sun, 10 Jan 2016 17:54:59 +0000 (18:54 +0100)]
Pyra+LC15: remove some debugging printf()
Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
H. Nikolaus Schaller [Sat, 9 Jan 2016 19:42:49 +0000 (20:42 +0100)]
LC15: fix pinmux address for gpio1_wk7
Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
H. Nikolaus Schaller [Sat, 9 Jan 2016 19:42:24 +0000 (20:42 +0100)]
Pyra+LC15: fix writing bq24297 registers
Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
H. Nikolaus Schaller [Sat, 9 Jan 2016 19:08:57 +0000 (20:08 +0100)]
Pyra+LC15: move bq24297 initialization to U-Boot where all I2C busses are working
Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
H. Nikolaus Schaller [Sat, 9 Jan 2016 18:58:05 +0000 (19:58 +0100)]
Pyra+LC15: tried to hack bq24297 driver into SPL (hangs: I2C2 does not initialize)
Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
H. Nikolaus Schaller [Sat, 9 Jan 2016 18:56:59 +0000 (19:56 +0100)]
LC15: preliminary code for boot switch (not tested)
Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
H. Nikolaus Schaller [Sat, 9 Jan 2016 15:01:21 +0000 (16:01 +0100)]
Pyra+LC15: add hook where we can increase the bq24297 current limit beyond 500mA
Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
H. Nikolaus Schaller [Sat, 9 Jan 2016 15:00:29 +0000 (16:00 +0100)]
Letux Cortex 15: define third MMC and prepare for uSD/eMMC switch control
Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
H. Nikolaus Schaller [Sat, 9 Jan 2016 14:58:22 +0000 (15:58 +0100)]
Pyra: code cleanup for the Pyra specific pinmux settings
Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
H. Nikolaus Schaller [Sat, 9 Jan 2016 14:57:01 +0000 (15:57 +0100)]
Pyra/LC15: unset CONFIG_SYS_MALLOC_CLEAR_ON_INIT because the memset(..., 16M) call in malloc init increases power consumption of OMAP5+DDR3 beyond what the bq24297 wants to supply and makes the Palmas shut down
Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
H. Nikolaus Schaller [Tue, 5 Jan 2016 12:08:21 +0000 (13:08 +0100)]
LC15 and Pyra+LC15: show different Board: message by u-boot
Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
H. Nikolaus Schaller [Wed, 23 Dec 2015 12:43:38 +0000 (13:43 +0100)]
Letux: bootscr: fixed boot scripts for OMAP5EVM and Pyra
Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
H. Nikolaus Schaller [Sat, 19 Dec 2015 14:41:58 +0000 (15:41 +0100)]
LC15: don't try mmc0/1 if loadbootscript succeeded; don't store environment in eMMC
Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
H. Nikolaus Schaller [Sat, 19 Dec 2015 14:40:43 +0000 (15:40 +0100)]
boot.scr: more fixes for all OMAP5 devices
Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
H. Nikolaus Schaller [Tue, 15 Dec 2015 06:57:43 +0000 (07:57 +0100)]
Letux: added more bootscript variants
Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
H. Nikolaus Schaller [Sat, 12 Dec 2015 21:58:29 +0000 (22:58 +0100)]
Pyra+LC15: use latest LC15 config and adjust where needed
Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
H. Nikolaus Schaller [Sat, 12 Dec 2015 21:57:51 +0000 (22:57 +0100)]
LC15: fix config and default boot script so that we can use a boot.scr
Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
H. Nikolaus Schaller [Sat, 12 Dec 2015 21:57:00 +0000 (22:57 +0100)]
boot-scr: adjust names to what the default boot script for omap5 is using
Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
H. Nikolaus Schaller [Sat, 12 Dec 2015 21:56:15 +0000 (22:56 +0100)]
omap5_uevm: don't call tca642x_set_inital_state() if CONFIG_TCA642X is not configured
Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
H. Nikolaus Schaller [Sat, 12 Dec 2015 14:31:29 +0000 (15:31 +0100)]
add Pyra config and board file and make it include the goldelico/letux-cortex15 code
Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
H. Nikolaus Schaller [Sat, 12 Dec 2015 14:30:08 +0000 (15:30 +0100)]
add Letux Cortex 15 config and board file and make it include the ti/omap5_evm code
Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
H. Nikolaus Schaller [Fri, 11 Dec 2015 13:37:45 +0000 (14:37 +0100)]
add boot script for letux cortex 15 board + pyra mainboard
Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
H. Nikolaus Schaller [Sun, 25 Oct 2015 16:43:20 +0000 (17:43 +0100)]
add bootscript source for omap5-uevm
Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
H. Nikolaus Schaller [Sun, 13 Sep 2015 08:04:49 +0000 (10:04 +0200)]
add boot script for letux cortex 15 board
Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
H. Nikolaus Schaller [Thu, 10 Dec 2015 18:02:09 +0000 (19:02 +0100)]
added pyra and lc15 defconfig
Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
Tom Rini [Mon, 11 Jul 2016 19:01:01 +0000 (15:01 -0400)]
Prepare v2016.07
Signed-off-by: Tom Rini <trini@konsulko.com>
Andre Przywara [Fri, 8 Jul 2016 14:25:23 +0000 (15:25 +0100)]
doc: ARMv8: add README.pine64
Since we lack information about the DRAM initialization for the
Allwinner A64 SoC, booting any A64 based board like the Pine64 is a bit
involved at the moment.
Add a README file to explain the process.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
[trini: Move to board/sunxi/ from doc/]
Signed-off-by: Tom Rini <trini@konsulko.com>
Stefano Babic [Mon, 11 Jul 2016 14:09:48 +0000 (16:09 +0200)]
mkimage -l is broken for images after gpimage
Because a gpimage cannot be detected, a false
GP header is printed instead of checking
for further image types.
Move gpimage as last to be linked, letting check
all other image types and printing a GP header just
in case no image is detected.
Signed-off-by: Stefano Babic <sbabic@denx.de>
jk.kernel@gmail.com [Sat, 9 Jul 2016 13:12:04 +0000 (21:12 +0800)]
git-mailrc: add rockchip alias
It's easier to Cc rockchip maintainers on rockchip-releated patches.
Signed-off-by: jk <jk.kernel@gmail.com>
Mingkai Hu [Thu, 7 Jul 2016 04:22:12 +0000 (12:22 +0800)]
armv8: Enable CPUECTLR.SMPEN for coherency
For A53, data coherency is enabled only when the CPUECTLR.SMPEN bit is
set. The SMPEN bit should be set before enabling the data cache.
If not enabled, the cache is not coherent with other cores and
data corruption could occur.
For A57/A72, SMPEN bit enables the processor to receive instruction
cache and TLB maintenance operations broadcast from other processors
in the cluster. This bit should be set before enabling the caches and
MMU, or performing any cache and TLB maintenance operations.
Signed-off-by: Mingkai Hu <mingkai.hu@nxp.com>
Signed-off-by: Gong Qianyu <Qianyu.Gong@nxp.com>
Reviewed-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Daniel Schwierzeck [Wed, 6 Jul 2016 10:44:22 +0000 (12:44 +0200)]
test/py: support 'memstart =' in u_boot_utils.find_ram_base()
Some archs like MIPS or PPC have a different 'bdinfo' output
than ARM regarding the memory configuration. Also support
'memstart = 0x*' in u_boot_utils.find_ram_base() to make
all tests requiring the RAM base working on those archs.
Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Stephen Warren [Wed, 6 Jul 2016 16:34:30 +0000 (10:34 -0600)]
test/py: strip VT100 codes from match buffer
Prior to this patch, any VT100 codes emitted by U-Boot are considered part
of a command's output, which often causes tests to fail. For example,
test_env_echo_exists executes printenv, and then considers any text on a
line before an = sign as a valid U-Boot environment variable name. This
includes any VT100 codes emitted. When the test later attempts to use that
variable, the name would be invalid since it includes the VT100 codes.
Solve this by stripping VT100 codes from the match buffer, so they are
never seen by higher level test code.
The codes are still logged unmodified, so that users can expect U-Boot's
exact output without interference. This does clutter the log file a bit.
However, it allows users to see exactly what U-Boot emitted rather than a
modified version, which hopefully is better for debugging. It's also much
simpler to implement, since logging happens as soon as text is received,
and so stripping the VT100 codes from the log would require handling
reception and stripping of partial VT100 codes.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Alexander Graf [Tue, 5 Jul 2016 18:37:17 +0000 (20:37 +0200)]
arm: Fix setjmp (again)
Commit e677724 (arm: Fix setjmp) added code to fix compilation of the setjmp
code path with thumv1. Unfortunately it missed a constraint that the adr
instruction can only refer to 4 byte aligned offsets.
So this patch adds the required alignment hooks to make compilation
work again even when setjmp doesn't happen to be 4 byte aligned.
Signed-off-by: Alexander Graf <agraf@suse.de>
Tested-by: Tom Rini <trini@konsulko.com>
Andre Przywara [Fri, 8 Jul 2016 14:18:35 +0000 (15:18 +0100)]
SPL: tiny-printf: avoid any BSS usage
As printf calls may be executed quite early, we should avoid using any
BSS stored variables, since some boards put BSS in DRAM, which may not
have been initialised yet.
Explicitly mark those "static global" variables as belonging to the
.data section, to keep tiny-printf clear of any BSS usage.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Stephen Warren [Wed, 6 Jul 2016 15:04:08 +0000 (09:04 -0600)]
test/py: fix CONFIG_ tests
Some CONFIG_ variables were recently renamed, but test/py wasn't updated
to match. This causes some tests to be skipped. Fix test/py so the tests
are run.
Fixes:
11636258981a ("Rename reset to sysreset")
Fixes:
f1f9d4fac527 ("hush: complete renaming CONFIG_SYS_HUSH_PARSER to CONFIG_HUSH_PARSER")
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Mateusz Kulikowski [Sun, 26 Jun 2016 20:43:55 +0000 (22:43 +0200)]
mmc: msm_sdhci: Set mmc->dev pointer in msm_sdc_probe()
MMC core expects (now) valid mmc->dev pointer.
During conversion in commit
cffe5d86 not every driver was updated.
This patch fixes crash while accessing MMC on
boards using Qualcomm SDHCI controller.
Signed-off-by: Mateusz Kulikowski <mateusz.kulikowski@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
Tom Rini [Thu, 7 Jul 2016 13:58:41 +0000 (09:58 -0400)]
Merge branch 'master' of git://git.denx.de/u-boot-usb
York Sun [Wed, 6 Jul 2016 23:39:51 +0000 (16:39 -0700)]
powerpc: mpc85xx: kmp204x: Fix compiling error for usb errata
Commit 9262367 moves USB errata workaround into a C file. This
causes compiling error for kmcoge4 and kmlion1. To enable the
errata workaround, define CONFIG_USB_EHCI_FSL in common header.
Signed-off-by: York Sun <york.sun@nxp.com>
Cc: Marek Vasut <marex@denx.de>
Cc: Ed Swarthout <Ed.Swarthout@nxp.com>
Cc: Sriram Dash <sriram.dash@nxp.com>
Fixes:
92623672f9d3 ("fsl: usb: make errata function common for PPC and ARM")
Tom Rini [Wed, 6 Jul 2016 19:55:36 +0000 (15:55 -0400)]
Merge branch 'master' of git://git.denx.de/u-boot-tegra
Tom Rini [Wed, 6 Jul 2016 19:55:21 +0000 (15:55 -0400)]
Merge branch 'master' of git://git.denx.de/u-boot-net
Oleksandr Tymoshenko [Fri, 1 Jul 2016 20:22:00 +0000 (13:22 -0700)]
net: rtl8169: Fix return value for rtl_send_common
Return value of rtl_send_common propogates unmodified all the way
up to eth_send and further to API consumer if CONFIG_API is enabled.
Previously rtl_send_common returned number of bytes sent on success
which was erroneouly detected as error condition by API consumers
that checked for operation success by comparing return value with 0.
Switch rtl_send_common to use common convention: return 0 on success
and negative value for failure.
Cc: Stephen Warren <swarren@nvidia.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Signed-off-by: Oleksandr Tymoshenko <gonzo@bluezbox.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Ralf Hubert [Fri, 1 Jul 2016 11:19:51 +0000 (13:19 +0200)]
net: Fix incorrect RPC packets on 64-bit systems
This patch fixes incorrect RPC packet layout caused by
'long' type size difference on 64 and 32-bit architectures.
Signed-off-by: Ralf Hubert <r.hubert@technisat.de>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Mingkai Hu [Fri, 1 Jul 2016 11:03:23 +0000 (19:03 +0800)]
driver: net: phylib: add support for aquantia AQR106/107 PHY
This patch adds support for aquantia AQR106/107 PHY.
Signed-off-by: Mingkai Hu <mingkai.hu@nxp.com>
Signed-off-by: Gong Qianyu <Qianyu.Gong@nxp.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Alexey Brodkin [Mon, 27 Jun 2016 10:17:51 +0000 (13:17 +0300)]
net: designware: Make driver independent from DM_GPIO again
Commit
90b7fc924adf "net: designware: support phy reset device-tree
bindings" made DW GMAC driver dependent on DM_GPIO by unconditional
usage of purely DM_GPIO stuff like:
* dm_gpio_XXX()
* gpio_request_by_name()
But since that driver as of today might be easily used without
DM_GPIO (that's the case for Synopsys AXS10x boards) we're
shielding all DM_GPIO things by ifdefs.
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Beniamino Galvani <b.galvani@gmail.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Sjoerd Simons <sjoerd.simons@collabora.co.uk>
Cc: Sonic Zhang <sonic.zhang@analog.com>
Cc: Bin Meng <bmeng.cn@gmail.com>
Cc: Marek Vasut <marex@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Joe Hershberger [Mon, 4 Apr 2016 09:07:33 +0000 (04:07 -0500)]
common: Always include errno.h in common.h
We want people using errnos for errors instead of -1, so make it easy
by always including the definition of all the errnos.
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Simon Glass [Sun, 8 May 2016 22:55:22 +0000 (16:55 -0600)]
fdt: Drop some unused compatible strings
We have driver-model drivers for some of these now, so drop them.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Simon Glass [Sun, 8 May 2016 22:55:21 +0000 (16:55 -0600)]
tegra: video: Always use write-through cache on LCD
This seems to give the best performance, so let's use it always.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Simon Glass [Sun, 8 May 2016 22:55:20 +0000 (16:55 -0600)]
video: tegra: Move to using simple-panel and pwm-backlight
We have standard drivers for panels and backlights which can do most of the
work for us. Move the tegra20 LCD driver over to use those instead of custom
code.
This patch includes device tree changes for the nvidia boards. I have only
been able to test seaboard. If this patch is applied, these boards will
also need to be synced with the kernel, and updated to use display-timings:
- colibri
- medcom-wide
- paz00
- tec
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Simon Glass [Sun, 8 May 2016 22:55:19 +0000 (16:55 -0600)]
tegra: dts: Sync tegra20 device tree files with Linux
Sync everything except the display panel, which will come in a future patch.
One USB port is left disabled since we don't want to support it in U-Boot.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Simon Glass [Sun, 8 May 2016 22:55:18 +0000 (16:55 -0600)]
errno: Allow errno_str() to be used without CONFIG_ERRNO_STR
The pmic framework uses errno_str() and this requires board that use it to
enable CONFIG_ERRNO_STR to avoid a build error. Update the header to provide
a NULL error message when CONFIG_ERRNO_STR is not defined, and fix the build
error.
This will show as "(null)" when U-Boot prints it.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Simon Glass [Sun, 8 May 2016 22:55:17 +0000 (16:55 -0600)]
errno: Add copyright header and header guard
Bring in a copyright for this file from cmd/pmic.c since this file was
submitted by the same author at around the same time. Also fix the missing
header guard.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Stephen Warren [Fri, 24 Jun 2016 14:36:04 +0000 (08:36 -0600)]
pci: tegra: actually program REFCLK_CFG* on recent SoCs
On recent SoCs, tegra_pcie_phy_enable() isn't called; but instead
tegra_pcie_enable_controller() calls tegra_xusb_phy_enable(). However,
part of tegra_pcie_phy_enable() needs to happen in all cases. Move that
code to tegra_pcie_port_enable() instead.
For reference, NVIDIA's downstream Linux kernel performs this operation
in tegra_pcie_enable_rp_features(), which is called immediately after
tegra_pcie_port_enable(). Since that function doesn't exist in the U-Boot
driver, we'll just add it to the tail of tegra_pcie_port_enable() instead.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Stephen Warren [Tue, 21 Jun 2016 18:47:51 +0000 (12:47 -0600)]
pci: tegra: correctly program PADS_REFCLK registers
The value that should be programmed into the PADS_REFCLK register varies
per SoC. Fix the Tegra PCIe driver to program the correct values. Future
SoCs will require different values in cfg0/1, so the two values are stored
separately in the per-SoC data structures.
For reference, the values are all documented in NV bug 1771116 comment 20.
The Tegra210 value doesn't match the current TRM, but I've filed a bug to
get the TRM fixed. Earlier TRMs don't document the value this register
should contain, but the ASIC team has validated all these values, except
for the Tegra20 value which is simply left unchanged in this patch.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Sjoerd Simons [Sun, 28 Feb 2016 21:40:02 +0000 (22:40 +0100)]
rockchip: video: Lower hpd wait time
Waiting 30 seconds for the hpd to go high seems a bit much, especially
on headless boots. Lowering the timeout to 300ms.
Sending as RFC because frankly i don't know what a sensible timeout is
here, but 30 seconds is clearly not it :)
Signed-off-by: Sjoerd Simons <sjoerd.simons@collabora.co.uk>
Reviewed-by: Simon Glass <sjg@chromium.org>
Dropped RFC tag:
Signed-off-by: Simon Glass <sjg@chromium.org>
Marek Vasut [Tue, 5 Jul 2016 15:40:27 +0000 (17:40 +0200)]
powerpc: mpc85xx: Do not build errata command in SPL
The errata command is useless in SPL, so don't build it. This fixes
multiple build failures on PowerPC.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: York Sun <york.sun@nxp.com>
Fixes:
92623672f9d3 ("fsl: usb: make errata function common for PPC and ARM")
Hans de Goede [Sun, 3 Jul 2016 18:22:05 +0000 (20:22 +0200)]
usb: dm: Make "usb info" use usb_for_each_root_dev()
The old dm "usb info" implementation has several issues:
1) NULL pointer deref when a bus has no children
2) Not showing usb devices on busses without an emulated root-hub (otg host)
3) Attempting to show devices on inactive busses
4) "usb info" Would cause some hosts to get re-probed something which only
"usb reset" should do
TL;DR: proper iterating over usb bus root devs is hard, use the helper
for it.
Reported-by: Bernhard Nortmann <bernhard.nortmann@web.de>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Hans de Goede [Sun, 3 Jul 2016 18:22:04 +0000 (20:22 +0200)]
usb: dm: Add a usb_for_each_root_dev() helper function
Iterating over usb-root devs and doing something for all of them is
a bit tricky with dm, factor out the proven usb_show_tree() for this
into a helper function.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Tom Rini [Mon, 4 Jul 2016 15:46:21 +0000 (11:46 -0400)]
Merge git://git.denx.de/u-boot-arc
Alexey Brodkin [Mon, 4 Jul 2016 08:37:55 +0000 (11:37 +0300)]
arc: make global_data.h usable in assembly files
Currently on attempt to use global_data.h in an assembly file following
will happen:
-------------------->8-----------------
./arch/arc/include/asm/global_data.h: Assembler messages:
./arch/arc/include/asm/global_data.h:11: Error: bad instruction 'struct arch_global_data{'
./arch/arc/include/asm/global_data.h:12: Error: junk at end of line, first unrecognized character is `}'
scripts/Makefile.build:316: recipe for target 'arch/arc/lib/start.o' failed
-------------------->8-----------------
In this change we disable struct arch_global_data in ASM which fixes
the issue above.
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Alexey Brodkin [Thu, 16 Jun 2016 08:55:00 +0000 (10:55 +0200)]
arc: Use "-mcpu=archs" instead of deprecated "-marchs" for ARC HS
Newer ARC toolchains don't support "-marchs" option any longer.
Instead "-mcpu=archs" should be used. What's also important older
toiolchains that support ARC HS cores will also happily accept
"-mcpu=archs" so that's a very safe move.
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Tom Rini [Sat, 2 Jul 2016 20:32:15 +0000 (16:32 -0400)]
Merge branch 'master' of git.denx.de/u-boot-sunxi
Quentin Schulz [Fri, 24 Jun 2016 12:33:35 +0000 (14:33 +0200)]
sunxi: Add defconfig and DTS file for Allwinner R16 EVB (Parrot)
The Parrot Board is an evaluation board with an Allwinner R16 (assumed
to be close to an Allwinner A33), 4GB of eMMC, 512MB of RAM, USB host
and OTG, a WiFi/Bluetooth combo chip, a micro SD Card reader, 2
controllable buttons, an LVDS port with separated backlight and
capacitive touch panel ports, an audio/microphone jack, a camera CSI
port, 2 sets of 22 GPIOs and an accelerometer.
The DTS file is identical to the one submitted to the upstream kernel.
Signed-off-by: Quentin Schulz <quentin.schulz@free-electrons.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Olliver Schinagl [Mon, 13 Jun 2016 16:13:07 +0000 (18:13 +0200)]
sunxi: Add missing boot_media fields in the SPL header
Commit
b19236fd1 ("sunxi: Increase SPL header size to 64 bytes to avoid
code corruption") Added defines for MMC0 and SPI as boot identification.
After verifying on an OLinuXino Lime2 with NAND and eMMC, the expected
values have been confirmed and added to spl.h
Signed-off-by: Olliver Schinagl <oliver@schinagl.nl>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Hans de Goede [Sun, 26 Jun 2016 11:56:01 +0000 (13:56 +0200)]
sunxi: spl: Fix DRAM info printing
The switch to simple_printf was causing the SPL dram info to show as:
DRAM: u MiB
This fixes this by switching from %lu to %d for printing the DRAM size.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Tom Rini [Sat, 2 Jul 2016 02:35:20 +0000 (22:35 -0400)]
Merge branch 'master' of git://git.denx.de/u-boot-usb
Tom Rini [Sat, 2 Jul 2016 02:35:12 +0000 (22:35 -0400)]
Merge branch 'master' of git://git.denx.de/u-boot-socfpga
Tom Rini [Fri, 1 Jul 2016 21:37:17 +0000 (17:37 -0400)]
Prepare v2016.07-rc3
Signed-off-by: Tom Rini <trini@konsulko.com>
Tom Rini [Fri, 1 Jul 2016 21:43:06 +0000 (17:43 -0400)]
Merge branch 'master' of git://git.denx.de/u-boot-uniphier
Steve Rae [Wed, 29 Jun 2016 20:42:01 +0000 (13:42 -0700)]
mmc: increase MMC SDHCI read status timeout
Otherwise, ocassionally see errors like this:
Flashing sparse image at offset 2078720
Flashing Sparse Image
sdhci_send_command: Timeout for status update!
mmc fail to send stop cmd
write_sparse_image: Write failed, block #2181088 [0]
This does not affect the actual writing speed, which is controlled by
the default value:
CONFIG_SDHCI_CMD_DEFAULT_TIMEOUT
It only increases the retries when reading:
SDHCI_INT_STATUS
to avoid the timeout error.
Signed-off-by: Steve Rae <steve.rae@raedomain.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Tested-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Tested-by: Jaehoon Chung <jh80.chung@samsung.com>
Lokesh Vutla [Wed, 29 Jun 2016 09:20:41 +0000 (14:50 +0530)]
ti_omap5_common: Find right dtb file for DRA72-RevC Evm
DRA72-Evm revC uses dra72-evm-revc.dtb. Update the same in env vatiables.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Masahiro Yamada [Mon, 27 Jun 2016 07:23:04 +0000 (16:23 +0900)]
autoboot: move bootdelay >= 0 check to abortboot()
Move the bootdelay >= 0 check to the caller, which simplifies
the callees.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Heiko Schocher <hs@denx.de>
Masahiro Yamada [Mon, 27 Jun 2016 07:23:03 +0000 (16:23 +0900)]
autoboot: move CONFIG_SILENT_CONSOLE handling
Factor out the same code from the callees to the caller.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Heiko Schocher <hs@denx.de>
Masahiro Yamada [Mon, 27 Jun 2016 07:23:02 +0000 (16:23 +0900)]
autoboot: rename abortboot_{keyed, normal} to __abortboot
Because abortboot_keyed() and abortboot_normal() are not compiled
at the same time, we can rename both of them to __abortboot().
This allows to drop #ifdef from the caller.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Heiko Schocher <hs@denx.de>
Masahiro Yamada [Mon, 27 Jun 2016 07:23:01 +0000 (16:23 +0900)]
autoboot: remove CONFIG_ZERO_BOOTDELAY_CHECK
As the help message of CONFIG_BOOTDELAY says, CONFIG_BOOTDELAY=-2
means the autoboot with no delay, with no abort check even if
CONFIG_ZERO_BOOTDELAY_CHECK is defined.
To sum up, the autoboot behaves as follows:
[1] CONFIG_BOOTDELAY=0 && CONFIG_ZERO_BOOTDELAY_CHECK=y
autoboot with no delay, but you can abort it by key input
[2] CONFIG_BOOTDELAY=0 && CONFIG_ZERO_BOOTDELAY_CHECK=n
autoboot with no delay, with no check for abort
[3] CONFIG_BOOTDELAY=-1
disable autoboot
[4] CONFIG_BOOTDELAY=-2
autoboot with no delay, with no check for abort
As you notice, [2] and [4] come to the same result, which means we
do not need CONFIG_ZERO_BOOTDELAY_CHECK. We can control all the
cases only by CONFIG_BOOTDELAY, like this:
[1] CONFIG_BOOTDELAY=0
autoboot with no delay, but you can abort it by key input
[2] CONFIG_BOOTDELAY=-1
disable autoboot
[3] CONFIG_BOOTDELAY=-2
autoboot with no delay, with no check for abort
This commit converts the logic as follow:
CONFIG_BOOTDELAY=0 && CONFIG_ZERO_BOOTDELAY_CHECK=n
--> CONFIG_BOOTDELAY=-2
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Vladimir Zapolskiy <vz@mleia.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
Acked-by: Christian Riesch <christian.riesch@omicronenergy.com>
Acked-by: Hannes Schmelzer <hannes.schmelzer@br-automation.com>
Masahiro Yamada [Mon, 27 Jun 2016 07:23:00 +0000 (16:23 +0900)]
doc: bootdelay: drop explanation about CONFIG_BOOTDELAY from README
The same information now exists in common/Kconfig. Do not duplicate
documentation from the point of view of maintainability.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Heiko Schocher <hs@denx.de>
Masahiro Yamada [Mon, 27 Jun 2016 07:22:59 +0000 (16:22 +0900)]
ARM: socfpga: move CONFIG_BOOTDELAY to Kconfig for IS1 board
This recently added board missed the tree-wide migration of
CONFIG_BOOTDELAY.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Pavel Machek <pavel@denx.de>
Reviewed-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Stefan Roese <sr@denx.de>
Andreas Dannenberg [Wed, 22 Jun 2016 22:10:26 +0000 (17:10 -0500)]
ARM: AM437x: Align HS device variant defconfig filename
Align the name of the defconfig file for high-security (HS) device variants
from the AM43xx family of SoCs with the corresponding name used for the
general purpose devices. This allows for easier cross-association of those
files and also provides room to grow from an HS device part number
perspective.
Furthermore, update and cleanup associated MAINTAINERS file.
Signed-off-by: Andreas Dannenberg <dannenberg@ti.com>
Cc: Lokesh Vutla <lokeshvutla@ti.com>
Cc: Madan Srinivas <madans@ti.com>
Praneeth Bajjuri [Tue, 21 Jun 2016 08:35:36 +0000 (14:05 +0530)]
driver: qspi: correct QSPI disable CS reset value
Correcting QSPI disable/unselect CS reset value.
CTRL_CORE_CONTROL_IO_2: QSPI_MEMMAPPED_CS[10:8]
This is not causing any issue, but its better
to untouch the reserved bits.
Praneeth Bajjuri <praneeth@ti.com>
Signed-off-by: Ravi Babu <ravibabu@ti.com>
Masahiro Yamada [Wed, 29 Jun 2016 10:39:03 +0000 (19:39 +0900)]
ARM: uniphier: add external IRQ setup code
I will carry this work-around until it is cared in the kernel.
This looks up the AIDET node and sets up a register to handle
active low interrupt signals.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Masahiro Yamada [Wed, 29 Jun 2016 10:39:02 +0000 (19:39 +0900)]
ARM: dts: uniphier: add AIDET nodes
The AIDET (ARM Interrupt Detector Add-on Circuit) is a kind of
syscon block related with the interrupt controller.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Masahiro Yamada [Wed, 29 Jun 2016 10:39:01 +0000 (19:39 +0900)]
pinctrl: uniphier: add Ethernet pin-mux settings
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Masahiro Yamada [Wed, 29 Jun 2016 10:39:00 +0000 (19:39 +0900)]
pinctrl: uniphier: avoid building unneeded pin-mux tables for SPL
SPL does not use all of the devices, so we can save some memory
footprint.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Masahiro Yamada [Wed, 29 Jun 2016 10:38:59 +0000 (19:38 +0900)]
pinctrl: uniphier: support pin configuration for dedicated pins
PH1-LD4 and PH1-sLD8 SoCs have pins that support pin configuration
(pin biasing, drive strength control), but not pin-muxing.
Allow to fill the mux value table with -1 for those pins; pins with
mux value -1 will be skipped in the pin-mux set function. The mux
value type should be changed from "unsigned" to "int" in order to
accommodate -1 as a special case.
[ Linux commit:
363c90e743b50a432a91a211dd8b078d9df446e9 ]
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Masahiro Yamada [Wed, 29 Jun 2016 10:38:58 +0000 (19:38 +0900)]
pinctrl: uniphier: split pinctrl driver for PH1-LD11 and PH1-LD20
PH1-LD11 and PH1-LD20 have much pin controlling in common, so I
added a single driver shared between them in the initial commit.
However, the Ethernet pin-mux settings I am going to add are
different with each other, and they may diverge more as the
progress of development. Split it into two dedicated drivers.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Masahiro Yamada [Wed, 29 Jun 2016 10:38:57 +0000 (19:38 +0900)]
pinctrl: uniphier: allow to have pinctrl node under syscon node
Currently, the UniPhier pinctrl driver itself is a syscon, but it
turned out much more reasonable to make it a child node of a syscon
because our syscon node consists of a bunch of system configuration
registers, not only pinctrl, but also phy, and misc registers.
It is difficult to split the node. This commit allows to migrate to
the new DT structure.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Masahiro Yamada [Wed, 29 Jun 2016 10:38:56 +0000 (19:38 +0900)]
ARM: dts: uniphier: sync Device Trees with upstream Linux
I periodically sync Device Trees for better maintainability.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Masahiro Yamada [Wed, 29 Jun 2016 10:38:55 +0000 (19:38 +0900)]
pinctrl: uniphier: remove unneeded pin group nand_cs1
This SoC does not support NAND CS1. This place-holder is no longer
necessary.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Masahiro Yamada [Wed, 29 Jun 2016 10:38:54 +0000 (19:38 +0900)]
pinctrl: uniphier: fix NAND pin-mux setting for PH1-LD11/LD20
My mistake in the initial support patch.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Masahiro Yamada [Wed, 29 Jun 2016 10:38:53 +0000 (19:38 +0900)]
pinctrl: uniphier: remove wrong pin-mux functions for ProXstream2
These are pin group names, not function names.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Masahiro Yamada [Fri, 24 Jun 2016 02:51:38 +0000 (11:51 +0900)]
ARM: uniphier: fix typo "talbe"
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>