--- /dev/null
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * Copyright (C) 2025 Amarula Solutions, Dario Binacchi <dario.binacchi@amarulasolutions.com>
+ *
+ * Inspired from the Linux kernel driver panel-novatek-nt35510.c
+ */
+
+#include <backlight.h>
+#include <dm.h>
+#include <mipi_dsi.h>
+#include <panel.h>
+#include <asm/gpio.h>
+#include <dm/device_compat.h>
+#include <linux/delay.h>
+#include <power/regulator.h>
+
+#define NT35510_CMD_CORRECT_GAMMA BIT(0)
+#define NT35510_CMD_CONTROL_DISPLAY BIT(1)
+#define NT35510_CMD_SETVCMOFF BIT(2)
+
+#define MCS_CMD_MAUCCTR 0xF0 /* Manufacturer command enable */
+#define MCS_CMD_READ_ID1 0xDA
+#define MCS_CMD_READ_ID2 0xDB
+#define MCS_CMD_READ_ID3 0xDC
+#define MCS_CMD_MTP_READ_SETTING 0xF8 /* Uncertain about name */
+#define MCS_CMD_MTP_READ_PARAM 0xFF /* Uncertain about name */
+
+/*
+ * These manufacturer commands are available after we enable manufacturer
+ * command set (MCS) for page 0.
+ */
+#define NT35510_P0_DOPCTR 0xB1
+#define NT35510_P0_SDHDTCTR 0xB6
+#define NT35510_P0_GSEQCTR 0xB7
+#define NT35510_P0_SDEQCTR 0xB8
+#define NT35510_P0_SDVPCTR 0xBA
+#define NT35510_P0_DPFRCTR1 0xBD
+#define NT35510_P0_DPFRCTR2 0xBE
+#define NT35510_P0_DPFRCTR3 0xBF
+#define NT35510_P0_DPMCTR12 0xCC
+
+#define NT35510_P0_DOPCTR_LEN 2
+#define NT35510_P0_GSEQCTR_LEN 2
+#define NT35510_P0_SDEQCTR_LEN 4
+#define NT35510_P0_SDVPCTR_LEN 1
+#define NT35510_P0_DPFRCTR1_LEN 5
+#define NT35510_P0_DPFRCTR2_LEN 5
+#define NT35510_P0_DPFRCTR3_LEN 5
+#define NT35510_P0_DPMCTR12_LEN 3
+
+#define NT35510_DOPCTR_0_RAMKP BIT(7) /* Contents kept in sleep */
+#define NT35510_DOPCTR_0_DSITE BIT(6) /* Enable TE signal */
+#define NT35510_DOPCTR_0_DSIG BIT(5) /* Enable generic read/write */
+#define NT35510_DOPCTR_0_DSIM BIT(4) /* Enable video mode on DSI */
+#define NT35510_DOPCTR_0_EOTP BIT(3) /* Support EoTP */
+#define NT35510_DOPCTR_0_N565 BIT(2) /* RGB or BGR pixel format */
+#define NT35510_DOPCTR_1_TW_PWR_SEL BIT(4) /* TE power selector */
+#define NT35510_DOPCTR_1_CRGB BIT(3) /* RGB or BGR byte order */
+#define NT35510_DOPCTR_1_CTB BIT(2) /* Vertical scanning direction */
+#define NT35510_DOPCTR_1_CRL BIT(1) /* Source driver data shift */
+#define NT35510_P0_SDVPCTR_PRG BIT(2) /* 0 = normal operation, 1 = VGLO */
+#define NT35510_P0_SDVPCTR_AVDD 0 /* source driver output = AVDD */
+#define NT35510_P0_SDVPCTR_OFFCOL 1 /* source driver output = off color */
+#define NT35510_P0_SDVPCTR_AVSS 2 /* source driver output = AVSS */
+#define NT35510_P0_SDVPCTR_HI_Z 3 /* source driver output = High impedance */
+
+/*
+ * These manufacturer commands are available after we enable manufacturer
+ * command set (MCS) for page 1.
+ */
+#define NT35510_P1_SETAVDD 0xB0
+#define NT35510_P1_SETAVEE 0xB1
+#define NT35510_P1_SETVCL 0xB2
+#define NT35510_P1_SETVGH 0xB3
+#define NT35510_P1_SETVRGH 0xB4
+#define NT35510_P1_SETVGL 0xB5
+#define NT35510_P1_BT1CTR 0xB6
+#define NT35510_P1_BT2CTR 0xB7
+#define NT35510_P1_BT3CTR 0xB8
+#define NT35510_P1_BT4CTR 0xB9 /* VGH boosting times/freq */
+#define NT35510_P1_BT5CTR 0xBA
+#define NT35510_P1_PFMCTR 0xBB
+#define NT35510_P1_SETVGP 0xBC
+#define NT35510_P1_SETVGN 0xBD
+#define NT35510_P1_SETVCMOFF 0xBE
+#define NT35510_P1_VGHCTR 0xBF /* VGH output ctrl */
+#define NT35510_P1_SET_GAMMA_RED_POS 0xD1
+#define NT35510_P1_SET_GAMMA_GREEN_POS 0xD2
+#define NT35510_P1_SET_GAMMA_BLUE_POS 0xD3
+#define NT35510_P1_SET_GAMMA_RED_NEG 0xD4
+#define NT35510_P1_SET_GAMMA_GREEN_NEG 0xD5
+#define NT35510_P1_SET_GAMMA_BLUE_NEG 0xD6
+
+/* AVDD and AVEE setting 3 bytes */
+#define NT35510_P1_AVDD_LEN 3
+#define NT35510_P1_AVEE_LEN 3
+#define NT35510_P1_VCL_LEN 3
+#define NT35510_P1_VGH_LEN 3
+#define NT35510_P1_VGL_LEN 3
+#define NT35510_P1_VGP_LEN 3
+#define NT35510_P1_VGN_LEN 3
+#define NT35510_P1_VCMOFF_LEN 2
+/* BT1CTR thru BT5CTR setting 3 bytes */
+#define NT35510_P1_BT1CTR_LEN 3
+#define NT35510_P1_BT2CTR_LEN 3
+#define NT35510_P1_BT3CTR_LEN 3
+#define NT35510_P1_BT4CTR_LEN 3
+#define NT35510_P1_BT5CTR_LEN 3
+/* 52 gamma parameters times two per color: positive and negative */
+#define NT35510_P1_GAMMA_LEN 52
+
+#define NT35510_WRCTRLD_BCTRL BIT(5)
+#define NT35510_WRCTRLD_A BIT(4)
+#define NT35510_WRCTRLD_DD BIT(3)
+#define NT35510_WRCTRLD_BL BIT(2)
+#define NT35510_WRCTRLD_DB BIT(1)
+#define NT35510_WRCTRLD_G BIT(0)
+
+#define NT35510_WRCABC_OFF 0
+#define NT35510_WRCABC_UI_MODE 1
+#define NT35510_WRCABC_STILL_MODE 2
+#define NT35510_WRCABC_MOVING_MODE 3
+
+/**
+ * struct nt35510_config - the display-specific NT35510 configuration
+ *
+ * Some of the settings provide an array of bytes, A, B C which mean:
+ * A = normal / idle off mode
+ * B = idle on mode
+ * C = partial / idle off mode
+ *
+ * Gamma correction arrays are 10bit numbers, two consecutive bytes
+ * makes out one point on the gamma correction curve. The points are
+ * not linearly placed along the X axis, we get points 0, 1, 3, 5
+ * 7, 11, 15, 23, 31, 47, 63, 95, 127, 128, 160, 192, 208, 224, 232,
+ * 240, 244, 248, 250, 252, 254, 255. The voltages tuples form
+ * V0, V1, V3 ... V255, with 0x0000 being the lowest voltage and
+ * 0x03FF being the highest voltage.
+ *
+ * Each value must be strictly higher than the previous value forming
+ * a rising curve like this:
+ *
+ * ^
+ * | V255
+ * | V254
+ * | ....
+ * | V5
+ * | V3
+ * | V1
+ * | V0
+ * +------------------------------------------->
+ *
+ * The details about all settings can be found in the NT35510 Application
+ * Note.
+ */
+struct nt35510_config {
+ /**
+ * @width_mm: physical panel width [mm]
+ */
+ u32 width_mm;
+ /**
+ * @height_mm: physical panel height [mm]
+ */
+ u32 height_mm;
+ /**
+ * @timings: display timings
+ */
+ struct display_timing timings;
+ /**
+ * @mode_flags: DSI operation mode related flags
+ */
+ unsigned long mode_flags;
+ /**
+ * @cmds: enable DSI commands
+ */
+ u32 cmds;
+ /**
+ * @avdd: setting for AVDD ranging from 0x00 = 6.5V to 0x14 = 4.5V
+ * in 0.1V steps the default is 0x05 which means 6.0V
+ */
+ u8 avdd[NT35510_P1_AVDD_LEN];
+ /**
+ * @bt1ctr: setting for boost power control for the AVDD step-up
+ * circuit (1)
+ * bits 0..2 in the lower nibble controls PCK, the booster clock
+ * frequency for the step-up circuit:
+ * 0 = Hsync/32
+ * 1 = Hsync/16
+ * 2 = Hsync/8
+ * 3 = Hsync/4
+ * 4 = Hsync/2
+ * 5 = Hsync
+ * 6 = Hsync x 2
+ * 7 = Hsync x 4
+ * bits 4..6 in the upper nibble controls BTP, the boosting
+ * amplification for the step-up circuit:
+ * 0 = Disable
+ * 1 = 1.5 x VDDB
+ * 2 = 1.66 x VDDB
+ * 3 = 2 x VDDB
+ * 4 = 2.5 x VDDB
+ * 5 = 3 x VDDB
+ * The defaults are 4 and 4 yielding 0x44
+ */
+ u8 bt1ctr[NT35510_P1_BT1CTR_LEN];
+ /**
+ * @avee: setting for AVEE ranging from 0x00 = -6.5V to 0x14 = -4.5V
+ * in 0.1V steps the default is 0x05 which means -6.0V
+ */
+ u8 avee[NT35510_P1_AVEE_LEN];
+ /**
+ * @bt2ctr: setting for boost power control for the AVEE step-up
+ * circuit (2)
+ * bits 0..2 in the lower nibble controls NCK, the booster clock
+ * frequency, the values are the same as for PCK in @bt1ctr.
+ * bits 4..5 in the upper nibble controls BTN, the boosting
+ * amplification for the step-up circuit.
+ * 0 = Disable
+ * 1 = -1.5 x VDDB
+ * 2 = -2 x VDDB
+ * 3 = -2.5 x VDDB
+ * 4 = -3 x VDDB
+ * The defaults are 4 and 3 yielding 0x34
+ */
+ u8 bt2ctr[NT35510_P1_BT2CTR_LEN];
+ /**
+ * @vcl: setting for VCL ranging from 0x00 = -2.5V to 0x11 = -4.0V
+ * in 1V steps, the default is 0x00 which means -2.5V
+ */
+ u8 vcl[NT35510_P1_VCL_LEN];
+ /**
+ * @bt3ctr: setting for boost power control for the VCL step-up
+ * circuit (3)
+ * bits 0..2 in the lower nibble controls CLCK, the booster clock
+ * frequency, the values are the same as for PCK in @bt1ctr.
+ * bits 4..5 in the upper nibble controls BTCL, the boosting
+ * amplification for the step-up circuit.
+ * 0 = Disable
+ * 1 = -0.5 x VDDB
+ * 2 = -1 x VDDB
+ * 3 = -2 x VDDB
+ * The defaults are 4 and 2 yielding 0x24
+ */
+ u8 bt3ctr[NT35510_P1_BT3CTR_LEN];
+ /**
+ * @vgh: setting for VGH ranging from 0x00 = 7.0V to 0x0B = 18.0V
+ * in 1V steps, the default is 0x08 which means 15V
+ */
+ u8 vgh[NT35510_P1_VGH_LEN];
+ /**
+ * @bt4ctr: setting for boost power control for the VGH step-up
+ * circuit (4)
+ * bits 0..2 in the lower nibble controls HCK, the booster clock
+ * frequency, the values are the same as for PCK in @bt1ctr.
+ * bits 4..5 in the upper nibble controls BTH, the boosting
+ * amplification for the step-up circuit.
+ * 0 = AVDD + VDDB
+ * 1 = AVDD - AVEE
+ * 2 = AVDD - AVEE + VDDB
+ * 3 = AVDD x 2 - AVEE
+ * The defaults are 4 and 3 yielding 0x34
+ */
+ u8 bt4ctr[NT35510_P1_BT4CTR_LEN];
+ /**
+ * @vgl: setting for VGL ranging from 0x00 = -2V to 0x0f = -15V in
+ * 1V steps, the default is 0x08 which means -10V
+ */
+ u8 vgl[NT35510_P1_VGL_LEN];
+ /**
+ * @bt5ctr: setting for boost power control for the VGL step-up
+ * circuit (5)
+ * bits 0..2 in the lower nibble controls LCK, the booster clock
+ * frequency, the values are the same as for PCK in @bt1ctr.
+ * bits 4..5 in the upper nibble controls BTL, the boosting
+ * amplification for the step-up circuit.
+ * 0 = AVEE + VCL
+ * 1 = AVEE - AVDD
+ * 2 = AVEE + VCL - AVDD
+ * 3 = AVEE x 2 - AVDD
+ * The defaults are 3 and 2 yielding 0x32
+ */
+ u8 bt5ctr[NT35510_P1_BT5CTR_LEN];
+ /**
+ * @vgp: setting for VGP, the positive gamma divider voltages
+ * VGMP the high voltage and VGSP the low voltage.
+ * The first byte contains bit 8 of VGMP and VGSP in bits 4 and 0
+ * The second byte contains bit 0..7 of VGMP
+ * The third byte contains bit 0..7 of VGSP
+ * VGMP 0x00 = 3.0V .. 0x108 = 6.3V in steps of 12.5mV
+ * VGSP 0x00 = 0V .. 0x111 = 3.7V in steps of 12.5mV
+ */
+ u8 vgp[NT35510_P1_VGP_LEN];
+ /**
+ * @vgn: setting for VGN, the negative gamma divider voltages,
+ * same layout of bytes as @vgp.
+ */
+ u8 vgn[NT35510_P1_VGN_LEN];
+ /**
+ * @vcmoff: setting the DC VCOM offset voltage
+ * The first byte contains bit 8 of VCM in bit 0 and VCMOFFSEL in bit 4.
+ * The second byte contains bits 0..7 of VCM.
+ * VCMOFFSEL the common voltage offset mode.
+ * VCMOFFSEL 0x00 = VCOM .. 0x01 Gamma.
+ * The default is 0x00.
+ * VCM the VCOM output voltage (VCMOFFSEL = 0) or the internal register
+ * offset for gamma voltage (VCMOFFSEL = 1).
+ * VCM 0x00 = 0V/0 .. 0x118 = 3.5V/280 in steps of 12.5mV/1step
+ * The default is 0x00 = 0V/0.
+ */
+ u8 vcmoff[NT35510_P1_VCMOFF_LEN];
+ /**
+ * @dopctr: setting optional control for display
+ * ERR bits 0..1 in the first byte is the ERR pin output signal setting.
+ * 0 = Disable, ERR pin output low
+ * 1 = ERR pin output CRC error only
+ * 2 = ERR pin output ECC error only
+ * 3 = ERR pin output CRC and ECC error
+ * The default is 0.
+ * N565 bit 2 in the first byte is the 16-bit/pixel format selection.
+ * 0 = R[4:0] + G[5:3] & G[2:0] + B[4:0]
+ * 1 = G[2:0] + R[4:0] & B[4:0] + G[5:3]
+ * The default is 0.
+ * DIS_EoTP_HS bit 3 in the first byte is "DSI protocol violation" error
+ * reporting.
+ * 0 = reporting when error
+ * 1 = not reporting when error
+ * DSIM bit 4 in the first byte is the video mode data type enable
+ * 0 = Video mode data type disable
+ * 1 = Video mode data type enable
+ * The default is 0.
+ * DSIG bit 5 int the first byte is the generic r/w data type enable
+ * 0 = Generic r/w disable
+ * 1 = Generic r/w enable
+ * The default is 0.
+ * DSITE bit 6 in the first byte is TE line enable
+ * 0 = TE line is disabled
+ * 1 = TE line is enabled
+ * The default is 0.
+ * RAMKP bit 7 in the first byte is the frame memory keep/loss in
+ * sleep-in mode
+ * 0 = contents loss in sleep-in
+ * 1 = contents keep in sleep-in
+ * The default is 0.
+ * CRL bit 1 in the second byte is the source driver data shift
+ * direction selection. This bit is XOR operation with bit RSMX
+ * of 3600h command.
+ * 0 (RMSX = 0) = S1 -> S1440
+ * 0 (RMSX = 1) = S1440 -> S1
+ * 1 (RMSX = 0) = S1440 -> S1
+ * 1 (RMSX = 1) = S1 -> S1440
+ * The default is 0.
+ * CTB bit 2 in the second byte is the vertical scanning direction
+ * selection for gate control signals. This bit is XOR operation
+ * with bit ML of 3600h command.
+ * 0 (ML = 0) = Forward (top -> bottom)
+ * 0 (ML = 1) = Reverse (bottom -> top)
+ * 1 (ML = 0) = Reverse (bottom -> top)
+ * 1 (ML = 1) = Forward (top -> bottom)
+ * The default is 0.
+ * CRGB bit 3 in the second byte is RGB-BGR order selection. This
+ * bit is XOR operation with bit RGB of 3600h command.
+ * 0 (RGB = 0) = RGB/Normal
+ * 0 (RGB = 1) = BGR/RB swap
+ * 1 (RGB = 0) = BGR/RB swap
+ * 1 (RGB = 1) = RGB/Normal
+ * The default is 0.
+ * TE_PWR_SEL bit 4 in the second byte is the TE output voltage
+ * level selection (only valid when DSTB_SEL = 0 or DSTB_SEL = 1,
+ * VSEL = High and VDDI = 1.665~3.3V).
+ * 0 = TE output voltage level is VDDI
+ * 1 = TE output voltage level is VDDA
+ * The default is 0.
+ */
+ u8 dopctr[NT35510_P0_DOPCTR_LEN];
+ /**
+ * @madctl: Memory data access control
+ * RSMY bit 0 is flip vertical. Flips the display image top to down.
+ * RSMX bit 1 is flip horizontal. Flips the display image left to right.
+ * MH bit 2 is the horizontal refresh order.
+ * RGB bit 3 is the RGB-BGR order.
+ * 0 = RGB color sequence
+ * 1 = BGR color sequence
+ * ML bit 4 is the vertical refresh order.
+ * MV bit 5 is the row/column exchange.
+ * MX bit 6 is the column address order.
+ * MY bit 7 is the row address order.
+ */
+ u8 madctl;
+ /**
+ * @sdhdtctr: source output data hold time
+ * 0x00..0x3F = 0..31.5us in steps of 0.5us
+ * The default is 0x05 = 2.5us.
+ */
+ u8 sdhdtctr;
+ /**
+ * @gseqctr: EQ control for gate signals
+ * GFEQ_XX[3:0]: time setting of EQ step for falling edge in steps
+ * of 0.5us.
+ * The default is 0x07 = 3.5us
+ * GREQ_XX[7:4]: time setting of EQ step for rising edge in steps
+ * of 0.5us.
+ * The default is 0x07 = 3.5us
+ */
+ u8 gseqctr[NT35510_P0_GSEQCTR_LEN];
+ /**
+ * @sdeqctr: Source driver control settings, first byte is
+ * 0 for mode 1 and 1 for mode 2. Mode 1 uses two steps and
+ * mode 2 uses three steps meaning EQS3 is not used in mode
+ * 1. Mode 2 is default. The last three parameters are EQS1, EQS2
+ * and EQS3, setting the rise time for each equalizer step:
+ * 0x00 = 0.0 us to 0x0f = 7.5 us in steps of 0.5us. The default
+ * is 0x07 = 3.5 us.
+ */
+ u8 sdeqctr[NT35510_P0_SDEQCTR_LEN];
+ /**
+ * @sdvpctr: power/voltage behaviour during vertical porch time
+ */
+ u8 sdvpctr;
+ /**
+ * @t1: the number of pixel clocks on one scanline, range
+ * 0x100 (258 ticks) .. 0x3FF (1024 ticks) so the value + 1
+ * clock ticks.
+ */
+ u16 t1;
+ /**
+ * @vbp: vertical back porch toward the PANEL note: not toward
+ * the DSI host; these are separate interfaces, in from DSI host
+ * and out to the panel.
+ */
+ u8 vbp;
+ /**
+ * @vfp: vertical front porch toward the PANEL.
+ */
+ u8 vfp;
+ /**
+ * @psel: pixel clock divisor: 0 = 1, 1 = 2, 2 = 4, 3 = 8.
+ */
+ u8 psel;
+ /**
+ * @dpmctr12: Display timing control 12
+ * Byte 1 bit 4 selects LVGL voltage level: 0 = VGLX, 1 = VGL_REG
+ * Byte 1 bit 1 selects gate signal mode: 0 = non-overlap, 1 = overlap
+ * Byte 1 bit 0 selects output signal control R/L swap, 0 = normal
+ * 1 = swap all O->E, L->R
+ * Byte 2 is CLW delay clock for CK O/E and CKB O/E signals:
+ * 0x00 = 0us .. 0xFF = 12.75us in 0.05us steps
+ * Byte 3 is FTI_H0 delay time for STP O/E signals:
+ * 0x00 = 0us .. 0xFF = 12.75us in 0.05us steps
+ */
+ u8 dpmctr12[NT35510_P0_DPMCTR12_LEN];
+ /**
+ * @gamma_corr_pos_r: Red gamma correction parameters, positive
+ */
+ u8 gamma_corr_pos_r[NT35510_P1_GAMMA_LEN];
+ /**
+ * @gamma_corr_pos_g: Green gamma correction parameters, positive
+ */
+ u8 gamma_corr_pos_g[NT35510_P1_GAMMA_LEN];
+ /**
+ * @gamma_corr_pos_b: Blue gamma correction parameters, positive
+ */
+ u8 gamma_corr_pos_b[NT35510_P1_GAMMA_LEN];
+ /**
+ * @gamma_corr_neg_r: Red gamma correction parameters, negative
+ */
+ u8 gamma_corr_neg_r[NT35510_P1_GAMMA_LEN];
+ /**
+ * @gamma_corr_neg_g: Green gamma correction parameters, negative
+ */
+ u8 gamma_corr_neg_g[NT35510_P1_GAMMA_LEN];
+ /**
+ * @gamma_corr_neg_b: Blue gamma correction parameters, negative
+ */
+ u8 gamma_corr_neg_b[NT35510_P1_GAMMA_LEN];
+ /**
+ * @wrdisbv: write display brightness
+ * 0x00 value means the lowest brightness and 0xff value means
+ * the highest brightness.
+ * The default is 0x00.
+ */
+ u8 wrdisbv;
+ /**
+ * @wrctrld: write control display
+ * G bit 0 selects gamma curve: 0 = Manual, 1 = Automatic
+ * DB bit 1 selects display brightness: 0 = Manual, 1 = Automatic
+ * BL bit 2 controls backlight control: 0 = Off, 1 = On
+ * DD bit 3 controls display dimming: 0 = Off, 1 = On
+ * A bit 4 controls LABC block: 0 = Off, 1 = On
+ * BCTRL bit 5 controls brightness block: 0 = Off, 1 = On
+ */
+ u8 wrctrld;
+ /**
+ * @wrcabc: write content adaptive brightness control
+ * There is possible to use 4 different modes for content adaptive
+ * image functionality:
+ * 0: Off
+ * 1: User Interface Image (UI-Mode)
+ * 2: Still Picture Image (Still-Mode)
+ * 3: Moving Picture Image (Moving-Mode)
+ * The default is 0
+ */
+ u8 wrcabc;
+ /**
+ * @wrcabcmb: write CABC minimum brightness
+ * Set the minimum brightness value of the display for CABC
+ * function.
+ * 0x00 value means the lowest brightness for CABC and 0xff
+ * value means the highest brightness for CABC.
+ * The default is 0x00.
+ */
+ u8 wrcabcmb;
+};
+
+/**
+ * struct nt35510 - state container for the NT35510 panel
+ */
+struct nt35510_panel_priv {
+ const struct nt35510_config *conf;
+ struct udevice *vdd_reg;
+ struct udevice *vddi_reg;
+ struct gpio_desc *reset;
+};
+
+/* Manufacturer command has strictly this byte sequence */
+static const u8 nt35510_mauc_mtp_read_param[] = { 0xAA, 0x55, 0x25, 0x01 };
+static const u8 nt35510_mauc_mtp_read_setting[] = { 0x01, 0x02, 0x00, 0x20,
+ 0x33, 0x13, 0x00, 0x40,
+ 0x00, 0x00, 0x23, 0x02 };
+static const u8 nt35510_mauc_select_page_0[] = { 0x55, 0xAA, 0x52, 0x08, 0x00 };
+static const u8 nt35510_mauc_select_page_1[] = { 0x55, 0xAA, 0x52, 0x08, 0x01 };
+static const u8 nt35510_vgh_on[] = { 0x01 };
+
+#define NT35510_ROTATE_0_SETTING 0x02
+#define NT35510_ROTATE_180_SETTING 0x00
+
+static inline struct mipi_dsi_device *to_mipi_dsi_device(struct udevice *dev)
+{
+ struct mipi_dsi_panel_plat *plat = dev_get_plat(dev);
+
+ return plat->device;
+}
+
+static inline const struct nt35510_config *to_panel_config(struct udevice *dev)
+{
+ struct nt35510_panel_priv *priv = dev_get_priv(dev);
+
+ return priv->conf;
+}
+
+static int nt35510_send_long(struct udevice *dev, u8 cmd, u8 cmdlen,
+ const u8 *seq)
+{
+ struct mipi_dsi_device *dsi = to_mipi_dsi_device(dev);
+ const u8 *seqp = seq;
+ int cmdwritten = 0;
+ int chunk = cmdlen;
+ int ret;
+
+ if (chunk > 15)
+ chunk = 15;
+ ret = mipi_dsi_dcs_write(dsi, cmd, seqp, chunk);
+ if (ret < 0) {
+ dev_err(dev, "error sending DCS command seq cmd %02x\n", cmd);
+ return ret;
+ }
+ cmdwritten += chunk;
+ seqp += chunk;
+
+ while (cmdwritten < cmdlen) {
+ chunk = cmdlen - cmdwritten;
+ if (chunk > 15)
+ chunk = 15;
+ ret = mipi_dsi_generic_write(dsi, seqp, chunk);
+ if (ret < 0) {
+ dev_err(dev, "error sending generic write seq %02x\n", cmd);
+ return ret;
+ }
+ cmdwritten += chunk;
+ seqp += chunk;
+ }
+ dev_dbg(dev, "sent command %02x %02x bytes\n", cmd, cmdlen);
+ return 0;
+}
+
+static int nt35510_setup_power(struct udevice *dev)
+{
+ const struct nt35510_config *conf = to_panel_config(dev);
+ int ret;
+
+ ret = nt35510_send_long(dev, NT35510_P1_SETAVDD,
+ NT35510_P1_AVDD_LEN,
+ conf->avdd);
+ if (ret)
+ return ret;
+
+ ret = nt35510_send_long(dev, NT35510_P1_BT1CTR,
+ NT35510_P1_BT1CTR_LEN,
+ conf->bt1ctr);
+ if (ret)
+ return ret;
+
+ ret = nt35510_send_long(dev, NT35510_P1_SETAVEE,
+ NT35510_P1_AVEE_LEN,
+ conf->avee);
+ if (ret)
+ return ret;
+
+ ret = nt35510_send_long(dev, NT35510_P1_BT2CTR,
+ NT35510_P1_BT2CTR_LEN,
+ conf->bt2ctr);
+ if (ret)
+ return ret;
+
+ ret = nt35510_send_long(dev, NT35510_P1_SETVCL,
+ NT35510_P1_VCL_LEN,
+ conf->vcl);
+ if (ret)
+ return ret;
+
+ ret = nt35510_send_long(dev, NT35510_P1_BT3CTR,
+ NT35510_P1_BT3CTR_LEN,
+ conf->bt3ctr);
+ if (ret)
+ return ret;
+
+ ret = nt35510_send_long(dev, NT35510_P1_SETVGH,
+ NT35510_P1_VGH_LEN,
+ conf->vgh);
+ if (ret)
+ return ret;
+
+ ret = nt35510_send_long(dev, NT35510_P1_BT4CTR,
+ NT35510_P1_BT4CTR_LEN,
+ conf->bt4ctr);
+ if (ret)
+ return ret;
+
+ ret = nt35510_send_long(dev, NT35510_P1_VGHCTR,
+ ARRAY_SIZE(nt35510_vgh_on),
+ nt35510_vgh_on);
+ if (ret)
+ return ret;
+
+ ret = nt35510_send_long(dev, NT35510_P1_SETVGL,
+ NT35510_P1_VGL_LEN,
+ conf->vgl);
+ if (ret)
+ return ret;
+
+ ret = nt35510_send_long(dev, NT35510_P1_BT5CTR,
+ NT35510_P1_BT5CTR_LEN,
+ conf->bt5ctr);
+ if (ret)
+ return ret;
+
+ ret = nt35510_send_long(dev, NT35510_P1_SETVGP,
+ NT35510_P1_VGP_LEN,
+ conf->vgp);
+ if (ret)
+ return ret;
+
+ ret = nt35510_send_long(dev, NT35510_P1_SETVGN,
+ NT35510_P1_VGN_LEN,
+ conf->vgn);
+ if (ret)
+ return ret;
+
+ if (conf->cmds & NT35510_CMD_SETVCMOFF) {
+ ret = nt35510_send_long(dev, NT35510_P1_SETVCMOFF,
+ NT35510_P1_VCMOFF_LEN,
+ conf->vcmoff);
+ if (ret)
+ return ret;
+ }
+
+ /* Typically 10 ms */
+ mdelay(10);
+
+ return 0;
+}
+
+static int nt35510_setup_display(struct udevice *dev)
+{
+ struct mipi_dsi_device *dsi = to_mipi_dsi_device(dev);
+ const struct nt35510_config *conf = to_panel_config(dev);
+ u8 dpfrctr[NT35510_P0_DPFRCTR1_LEN];
+ int ret;
+
+ ret = nt35510_send_long(dev, NT35510_P0_DOPCTR,
+ NT35510_P0_DOPCTR_LEN,
+ conf->dopctr);
+ if (ret)
+ return ret;
+
+ ret = mipi_dsi_dcs_write(dsi, MIPI_DCS_SET_ADDRESS_MODE, &conf->madctl,
+ sizeof(conf->madctl));
+ if (ret < 0)
+ return ret;
+
+ ret = mipi_dsi_dcs_write(dsi, NT35510_P0_SDHDTCTR, &conf->sdhdtctr,
+ sizeof(conf->sdhdtctr));
+ if (ret < 0)
+ return ret;
+
+ ret = nt35510_send_long(dev, NT35510_P0_GSEQCTR,
+ NT35510_P0_GSEQCTR_LEN,
+ conf->gseqctr);
+ if (ret)
+ return ret;
+
+ ret = nt35510_send_long(dev, NT35510_P0_SDEQCTR,
+ NT35510_P0_SDEQCTR_LEN,
+ conf->sdeqctr);
+ if (ret)
+ return ret;
+
+ ret = mipi_dsi_dcs_write(dsi, NT35510_P0_SDVPCTR,
+ &conf->sdvpctr, 1);
+ if (ret < 0)
+ return ret;
+
+ /*
+ * Display timing control for active and idle off mode:
+ * the first byte contains
+ * the two high bits of T1A and second byte the low 8 bits, and
+ * the valid range is 0x100 (257) to 0x3ff (1023) representing
+ * 258..1024 (+1) pixel clock ticks for one scanline. At 20MHz pixel
+ * clock this covers the range of 12.90us .. 51.20us in steps of
+ * 0.05us, the default is 0x184 (388) representing 389 ticks.
+ * The third byte is VBPDA, vertical back porch display active
+ * and the fourth VFPDA, vertical front porch display active,
+ * both given in number of scanlines in the range 0x02..0xff
+ * for 2..255 scanlines. The fifth byte is 2 bits selecting
+ * PSEL for active and idle off mode, how much the 20MHz clock
+ * is divided by 0..3. This needs to be adjusted to get the right
+ * frame rate.
+ */
+ dpfrctr[0] = (conf->t1 >> 8) & 0xFF;
+ dpfrctr[1] = conf->t1 & 0xFF;
+ /* Vertical back porch */
+ dpfrctr[2] = conf->vbp;
+ /* Vertical front porch */
+ dpfrctr[3] = conf->vfp;
+ dpfrctr[4] = conf->psel;
+ ret = nt35510_send_long(dev, NT35510_P0_DPFRCTR1,
+ NT35510_P0_DPFRCTR1_LEN,
+ dpfrctr);
+ if (ret)
+ return ret;
+ /* For idle and partial idle off mode we decrease front porch by one */
+ dpfrctr[3]--;
+ ret = nt35510_send_long(dev, NT35510_P0_DPFRCTR2,
+ NT35510_P0_DPFRCTR2_LEN,
+ dpfrctr);
+ if (ret)
+ return ret;
+ ret = nt35510_send_long(dev, NT35510_P0_DPFRCTR3,
+ NT35510_P0_DPFRCTR3_LEN,
+ dpfrctr);
+ if (ret)
+ return ret;
+
+ /* Enable TE on vblank */
+ ret = mipi_dsi_dcs_set_tear_on(dsi, MIPI_DSI_DCS_TEAR_MODE_VBLANK);
+ if (ret)
+ return ret;
+
+ /* Turn on the pads? */
+ ret = nt35510_send_long(dev, NT35510_P0_DPMCTR12,
+ NT35510_P0_DPMCTR12_LEN,
+ conf->dpmctr12);
+ if (ret)
+ return ret;
+
+ return 0;
+}
+
+static int nt35510_read_id(struct udevice *dev)
+{
+ struct mipi_dsi_device *dsi = to_mipi_dsi_device(dev);
+ u8 id1, id2, id3;
+ int ret;
+
+ ret = mipi_dsi_dcs_read(dsi, MCS_CMD_READ_ID1, &id1, 1);
+ if (ret < 0) {
+ dev_err(dev, "could not read MTP ID1\n");
+ return ret;
+ }
+
+ ret = mipi_dsi_dcs_read(dsi, MCS_CMD_READ_ID2, &id2, 1);
+ if (ret < 0) {
+ dev_err(dev, "could not read MTP ID2\n");
+ return ret;
+ }
+
+ ret = mipi_dsi_dcs_read(dsi, MCS_CMD_READ_ID3, &id3, 1);
+ if (ret < 0) {
+ dev_err(dev, "could not read MTP ID3\n");
+ return ret;
+ }
+
+ /*
+ * Multi-Time Programmable (?) memory contains manufacturer
+ * ID (e.g. Hydis 0x55), driver ID (e.g. NT35510 0xc0) and
+ * version.
+ */
+ dev_info(dev, "MTP ID manufacturer: %02x version: %02x driver: %02x\n",
+ id1, id2, id3);
+
+ return 0;
+}
+
+static int nt35510_init_sequence(struct udevice *dev)
+{
+ const struct nt35510_config *conf = to_panel_config(dev);
+ int ret;
+
+ ret = nt35510_send_long(dev, MCS_CMD_MTP_READ_PARAM,
+ ARRAY_SIZE(nt35510_mauc_mtp_read_param),
+ nt35510_mauc_mtp_read_param);
+ if (ret)
+ return ret;
+
+ ret = nt35510_send_long(dev, MCS_CMD_MTP_READ_SETTING,
+ ARRAY_SIZE(nt35510_mauc_mtp_read_setting),
+ nt35510_mauc_mtp_read_setting);
+ if (ret)
+ return ret;
+
+ nt35510_read_id(dev);
+
+ /* Set up stuff in manufacturer control, page 1 */
+ ret = nt35510_send_long(dev, MCS_CMD_MAUCCTR,
+ ARRAY_SIZE(nt35510_mauc_select_page_1),
+ nt35510_mauc_select_page_1);
+ if (ret)
+ return ret;
+
+ ret = nt35510_setup_power(dev);
+ if (ret)
+ return ret;
+
+ if (conf->cmds & NT35510_CMD_CORRECT_GAMMA) {
+ ret = nt35510_send_long(dev, NT35510_P1_SET_GAMMA_RED_POS,
+ NT35510_P1_GAMMA_LEN,
+ conf->gamma_corr_pos_r);
+ if (ret)
+ return ret;
+
+ ret = nt35510_send_long(dev, NT35510_P1_SET_GAMMA_GREEN_POS,
+ NT35510_P1_GAMMA_LEN,
+ conf->gamma_corr_pos_g);
+ if (ret)
+ return ret;
+
+ ret = nt35510_send_long(dev, NT35510_P1_SET_GAMMA_BLUE_POS,
+ NT35510_P1_GAMMA_LEN,
+ conf->gamma_corr_pos_b);
+ if (ret)
+ return ret;
+
+ ret = nt35510_send_long(dev, NT35510_P1_SET_GAMMA_RED_NEG,
+ NT35510_P1_GAMMA_LEN,
+ conf->gamma_corr_neg_r);
+ if (ret)
+ return ret;
+
+ ret = nt35510_send_long(dev, NT35510_P1_SET_GAMMA_GREEN_NEG,
+ NT35510_P1_GAMMA_LEN,
+ conf->gamma_corr_neg_g);
+ if (ret)
+ return ret;
+
+ ret = nt35510_send_long(dev, NT35510_P1_SET_GAMMA_BLUE_NEG,
+ NT35510_P1_GAMMA_LEN,
+ conf->gamma_corr_neg_b);
+ if (ret)
+ return ret;
+ }
+
+ /* Set up stuff in manufacturer control, page 0 */
+ ret = nt35510_send_long(dev, MCS_CMD_MAUCCTR,
+ ARRAY_SIZE(nt35510_mauc_select_page_0),
+ nt35510_mauc_select_page_0);
+ if (ret)
+ return ret;
+
+ ret = nt35510_setup_display(dev);
+ if (ret)
+ return ret;
+
+ return 0;
+}
+
+static int nt35510_panel_enable_backlight(struct udevice *dev)
+{
+ struct mipi_dsi_device *dsi = to_mipi_dsi_device(dev);
+ const struct nt35510_config *conf = to_panel_config(dev);
+ int ret;
+
+ ret = mipi_dsi_attach(dsi);
+ if (ret < 0)
+ return ret;
+
+ ret = nt35510_init_sequence(dev);
+ if (ret)
+ return ret;
+
+ /* Exit sleep mode */
+ ret = mipi_dsi_dcs_exit_sleep_mode(dsi);
+ if (ret) {
+ dev_err(dev, "failed to exit sleep mode (%d)\n", ret);
+ return ret;
+ }
+
+ /* Up to 120 ms */
+ mdelay(120);
+
+ if (conf->cmds & NT35510_CMD_CONTROL_DISPLAY) {
+ ret = mipi_dsi_dcs_write(dsi, MIPI_DCS_WRITE_CONTROL_DISPLAY,
+ &conf->wrctrld,
+ sizeof(conf->wrctrld));
+ if (ret < 0)
+ return ret;
+
+ ret = mipi_dsi_dcs_write(dsi, MIPI_DCS_WRITE_POWER_SAVE,
+ &conf->wrcabc,
+ sizeof(conf->wrcabc));
+ if (ret < 0)
+ return ret;
+
+ ret = mipi_dsi_dcs_write(dsi, MIPI_DCS_SET_CABC_MIN_BRIGHTNESS,
+ &conf->wrcabcmb,
+ sizeof(conf->wrcabcmb));
+ if (ret < 0)
+ return ret;
+ }
+
+ ret = mipi_dsi_dcs_set_display_on(dsi);
+ if (ret) {
+ dev_err(dev, "failed to turn display on (%d)\n", ret);
+ return ret;
+ }
+
+ /* Some 10 ms */
+ mdelay(10);
+
+ ret = mipi_dsi_dcs_set_display_brightness(dsi, 0x7f);
+ if (ret < 0)
+ return ret;
+
+ /* Need to wait a few time before sending the first image */
+ mdelay(10);
+
+ return 0;
+}
+
+static int nt35510_panel_get_display_timing(struct udevice *dev,
+ struct display_timing *timings)
+{
+ struct nt35510_panel_priv *priv = dev_get_priv(dev);
+
+ memcpy(timings, &priv->conf->timings, sizeof(*timings));
+ return 0;
+}
+
+static int nt35510_panel_of_to_plat(struct udevice *dev)
+{
+ struct nt35510_panel_priv *priv = dev_get_priv(dev);
+ int ret;
+
+ if (CONFIG_IS_ENABLED(DM_REGULATOR)) {
+ ret = device_get_supply_regulator(dev, "vdd-supply",
+ &priv->vdd_reg);
+ if (ret) {
+ dev_err(dev, "Warning: cannot get vdd supply\n");
+ return ret;
+ }
+
+ ret = device_get_supply_regulator(dev, "vddi-supply",
+ &priv->vddi_reg);
+ if (ret) {
+ dev_err(dev, "Warning: cannot get vddi supply\n");
+ return ret;
+ }
+ }
+
+ priv->reset =
+ devm_gpiod_get_optional(dev, "reset",
+ GPIOD_IS_OUT | GPIOD_IS_OUT_ACTIVE);
+ if (IS_ERR(priv->reset)) {
+ dev_err(dev, "error getting RESET GPIO\n");
+ return PTR_ERR(priv->reset);
+ }
+
+ return 0;
+}
+
+static int nt35510_panel_probe(struct udevice *dev)
+{
+ struct nt35510_panel_priv *priv = dev_get_priv(dev);
+ struct mipi_dsi_panel_plat *plat = dev_get_plat(dev);
+ int ret;
+
+ priv->conf = (struct nt35510_config *)dev_get_driver_data(dev);
+ if (!priv->conf) {
+ dev_err(dev, "missing device configuration\n");
+ return -ENODEV;
+ }
+
+ if (CONFIG_IS_ENABLED(DM_REGULATOR)) {
+ dev_dbg(dev, "enable regulator '%s'\n", priv->vdd_reg->name);
+ ret = regulator_set_enable(priv->vdd_reg, true);
+ if (ret)
+ return ret;
+
+ dev_dbg(dev, "enable regulator '%s'\n", priv->vddi_reg->name);
+ ret = regulator_set_enable(priv->vddi_reg, true);
+ if (ret)
+ return ret;
+ }
+
+ /* Toggle RESET in accordance with datasheet page 370 */
+ if (priv->reset) {
+ dm_gpio_set_value(priv->reset, 1);
+ /* Active min 10 us according to datasheet, let's say 20 */
+ mdelay(1);
+ dm_gpio_set_value(priv->reset, 0);
+ /*
+ * 5 ms during sleep mode, 120 ms during sleep out mode
+ * according to datasheet, let's use 15 ms.
+ */
+ mdelay(150);
+ }
+
+ plat->lanes = 2;
+ plat->format = MIPI_DSI_FMT_RGB888;
+ plat->mode_flags = priv->conf->mode_flags;
+
+ return 0;
+}
+
+static const struct panel_ops nt35510_panel_ops = {
+ .enable_backlight = nt35510_panel_enable_backlight,
+ .get_display_timing = nt35510_panel_get_display_timing,
+};
+
+/*
+ * These gamma correction values are 10bit tuples, so only bits 0 and 1 is
+ * ever used in the first byte. They form a positive and negative gamma
+ * correction curve for each color, values must be strictly higher for each
+ * step on the curve. As can be seen these default curves goes from 0x0001
+ * to 0x03FE.
+ */
+#define NT35510_GAMMA_POS_DEFAULT 0x00, 0x01, 0x00, 0x43, 0x00, \
+ 0x6B, 0x00, 0x87, 0x00, 0xA3, 0x00, 0xCE, 0x00, 0xF1, 0x01, \
+ 0x27, 0x01, 0x53, 0x01, 0x98, 0x01, 0xCE, 0x02, 0x22, 0x02, \
+ 0x83, 0x02, 0x78, 0x02, 0x9E, 0x02, 0xDD, 0x03, 0x00, 0x03, \
+ 0x2E, 0x03, 0x54, 0x03, 0x7F, 0x03, 0x95, 0x03, 0xB3, 0x03, \
+ 0xC2, 0x03, 0xE1, 0x03, 0xF1, 0x03, 0xFE
+
+#define NT35510_GAMMA_NEG_DEFAULT 0x00, 0x01, 0x00, 0x43, 0x00, \
+ 0x6B, 0x00, 0x87, 0x00, 0xA3, 0x00, 0xCE, 0x00, 0xF1, 0x01, \
+ 0x27, 0x01, 0x53, 0x01, 0x98, 0x01, 0xCE, 0x02, 0x22, 0x02, \
+ 0x43, 0x02, 0x50, 0x02, 0x9E, 0x02, 0xDD, 0x03, 0x00, 0x03, \
+ 0x2E, 0x03, 0x54, 0x03, 0x7F, 0x03, 0x95, 0x03, 0xB3, 0x03, \
+ 0xC2, 0x03, 0xE1, 0x03, 0xF1, 0x03, 0xFE
+
+/*
+ * The Hydis HVA40WV1 panel
+ */
+static const struct nt35510_config nt35510_hydis_hva40wv1 = {
+ .width_mm = 52,
+ .height_mm = 86,
+ /**
+ * As the Hydis panel is used in command mode, the porches etc
+ * are settings programmed internally into the NT35510 controller
+ * and generated toward the physical display. As the panel is not
+ * used in video mode, these are not really exposed to the DSI
+ * host.
+ *
+ * Display frame rate control:
+ * Frame rate = (20 MHz / 1) / (389 * (7 + 50 + 800)) ~= 60 Hz
+ */
+ .timings = {
+ /* The internal pixel clock of the NT35510 is 20 MHz */
+ .pixelclock.typ = 20000,
+ .hactive.typ = 480,
+ .hfront_porch.typ = 2,
+ .hsync_len.typ = 0,
+ .hback_porch.typ = 5,
+ .vactive.typ = 800,
+ .vfront_porch.typ = 2,
+ .vsync_len.typ = 0,
+ .vback_porch.typ = 5,
+ },
+ .mode_flags = MIPI_DSI_CLOCK_NON_CONTINUOUS,
+ .cmds = NT35510_CMD_CORRECT_GAMMA,
+ /* 0x09: AVDD = 5.6V */
+ .avdd = { 0x09, 0x09, 0x09 },
+ /* 0x34: PCK = Hsync/2, BTP = 2 x VDDB */
+ .bt1ctr = { 0x34, 0x34, 0x34 },
+ /* 0x09: AVEE = -5.6V */
+ .avee = { 0x09, 0x09, 0x09 },
+ /* 0x24: NCK = Hsync/2, BTN = -2 x VDDB */
+ .bt2ctr = { 0x24, 0x24, 0x24 },
+ /* VBCLA: -2.5V, VBCLB: -2.5V, VBCLC: -2.5V */
+ .vcl = { 0x00, 0x00, 0x00 },
+ /* 0x24: CLCK = Hsync/2, BTN = -1 x VDDB */
+ .bt3ctr = { 0x24, 0x24, 0x24 },
+ /* 0x05 = 12V */
+ .vgh = { 0x05, 0x05, 0x05 },
+ /* 0x24: NCKA = Hsync/2, VGH = 2 x AVDD - AVEE */
+ .bt4ctr = { 0x24, 0x24, 0x24 },
+ /* 0x0B = -13V */
+ .vgl = { 0x0B, 0x0B, 0x0B },
+ /* 0x24: LCKA = Hsync, VGL = AVDD + VCL - AVDD */
+ .bt5ctr = { 0x24, 0x24, 0x24 },
+ /* VGMP: 0x0A3 = 5.0375V, VGSP = 0V */
+ .vgp = { 0x00, 0xA3, 0x00 },
+ /* VGMP: 0x0A3 = 5.0375V, VGSP = 0V */
+ .vgn = { 0x00, 0xA3, 0x00 },
+ /* VCMOFFSEL = VCOM voltage offset mode, VCM = 0V */
+ .vcmoff = { 0x00, 0x00 },
+ /* Enable TE, EoTP and RGB pixel format */
+ .dopctr = { NT35510_DOPCTR_0_DSITE | NT35510_DOPCTR_0_EOTP |
+ NT35510_DOPCTR_0_N565, NT35510_DOPCTR_1_CTB },
+ .madctl = NT35510_ROTATE_0_SETTING,
+ /* 0x0A: SDT = 5 us */
+ .sdhdtctr = 0x0A,
+ /* EQ control for gate signals, 0x00 = 0 us */
+ .gseqctr = { 0x00, 0x00 },
+ /* SDEQCTR: source driver EQ mode 2, 2.5 us rise time on each step */
+ .sdeqctr = { 0x01, 0x05, 0x05, 0x05 },
+ /* SDVPCTR: Normal operation off color during v porch */
+ .sdvpctr = 0x01,
+ /* T1: number of pixel clocks on one scanline: 0x184 = 389 clocks */
+ .t1 = 0x0184,
+ /* VBP: vertical back porch toward the panel */
+ .vbp = 7,
+ /* VFP: vertical front porch toward the panel */
+ .vfp = 50,
+ /* PSEL: divide pixel clock 20MHz with 1 (no clock downscaling) */
+ .psel = 0,
+ /* DPTMCTR12: 0x03: LVGL = VGLX, overlap mode, swap R->L O->E */
+ .dpmctr12 = { 0x03, 0x00, 0x00, },
+ /* Default gamma correction values */
+ .gamma_corr_pos_r = { NT35510_GAMMA_POS_DEFAULT },
+ .gamma_corr_pos_g = { NT35510_GAMMA_POS_DEFAULT },
+ .gamma_corr_pos_b = { NT35510_GAMMA_POS_DEFAULT },
+ .gamma_corr_neg_r = { NT35510_GAMMA_NEG_DEFAULT },
+ .gamma_corr_neg_g = { NT35510_GAMMA_NEG_DEFAULT },
+ .gamma_corr_neg_b = { NT35510_GAMMA_NEG_DEFAULT },
+};
+
+static const struct nt35510_config nt35510_frida_frd400b25025 = {
+ .width_mm = 52,
+ .height_mm = 86,
+ .timings = {
+ .pixelclock.typ = 23000000,
+ .hactive.typ = 480,
+ .hfront_porch.typ = 34,
+ .hback_porch.typ = 34,
+ .hsync_len.typ = 2,
+ .vactive.typ = 800,
+ .vfront_porch.typ = 15,
+ .vback_porch.typ = 15,
+ .vsync_len.typ = 12,
+ },
+ .mode_flags = MIPI_DSI_MODE_VIDEO | MIPI_DSI_MODE_VIDEO_BURST |
+ MIPI_DSI_MODE_LPM,
+ .cmds = NT35510_CMD_CONTROL_DISPLAY | NT35510_CMD_SETVCMOFF,
+ /* 0x03: AVDD = 6.2V */
+ .avdd = { 0x03, 0x03, 0x03 },
+ /* 0x46: PCK = 2 x Hsync, BTP = 2.5 x VDDB */
+ .bt1ctr = { 0x46, 0x46, 0x46 },
+ /* 0x03: AVEE = -6.2V */
+ .avee = { 0x03, 0x03, 0x03 },
+ /* 0x36: PCK = 2 x Hsync, BTP = 2 x VDDB */
+ .bt2ctr = { 0x36, 0x36, 0x36 },
+ /* VBCLA: -2.5V, VBCLB: -2.5V, VBCLC: -3.5V */
+ .vcl = { 0x00, 0x00, 0x02 },
+ /* 0x26: CLCK = 2 x Hsync, BTN = -1 x VDDB */
+ .bt3ctr = { 0x26, 0x26, 0x26 },
+ /* 0x09 = 16V */
+ .vgh = { 0x09, 0x09, 0x09 },
+ /* 0x36: HCK = 2 x Hsync, VGH = 2 x AVDD - AVEE */
+ .bt4ctr = { 0x36, 0x36, 0x36 },
+ /* 0x08 = -10V */
+ .vgl = { 0x08, 0x08, 0x08 },
+ /* 0x26: LCK = 2 x Hsync, VGL = AVDD + VCL - AVDD */
+ .bt5ctr = { 0x26, 0x26, 0x26 },
+ /* VGMP: 0x080 = 4.6V, VGSP = 0V */
+ .vgp = { 0x00, 0x80, 0x00 },
+ /* VGMP: 0x080 = 4.6V, VGSP = 0V */
+ .vgn = { 0x00, 0x80, 0x00 },
+ /* VCMOFFSEL = VCOM voltage offset mode, VCM = -1V */
+ .vcmoff = { 0x00, 0x50 },
+ .dopctr = { NT35510_DOPCTR_0_RAMKP | NT35510_DOPCTR_0_DSITE |
+ NT35510_DOPCTR_0_DSIG | NT35510_DOPCTR_0_DSIM |
+ NT35510_DOPCTR_0_EOTP | NT35510_DOPCTR_0_N565, 0 },
+ .madctl = NT35510_ROTATE_180_SETTING,
+ /* 0x03: SDT = 1.5 us */
+ .sdhdtctr = 0x03,
+ /* EQ control for gate signals, 0x00 = 0 us */
+ .gseqctr = { 0x00, 0x00 },
+ /* SDEQCTR: source driver EQ mode 2, 1 us rise time on each step */
+ .sdeqctr = { 0x01, 0x02, 0x02, 0x02 },
+ /* SDVPCTR: Normal operation off color during v porch */
+ .sdvpctr = 0x01,
+ /* T1: number of pixel clocks on one scanline: 0x184 = 389 clocks */
+ .t1 = 0x0184,
+ /* VBP: vertical back porch toward the panel */
+ .vbp = 0x1C,
+ /* VFP: vertical front porch toward the panel */
+ .vfp = 0x1C,
+ /* PSEL: divide pixel clock 23MHz with 1 (no clock downscaling) */
+ .psel = 0,
+ /* DPTMCTR12: 0x03: LVGL = VGLX, overlap mode, swap R->L O->E */
+ .dpmctr12 = { 0x03, 0x00, 0x00, },
+ /* write display brightness */
+ .wrdisbv = 0x7f,
+ /* write control display */
+ .wrctrld = NT35510_WRCTRLD_BCTRL | NT35510_WRCTRLD_DD |
+ NT35510_WRCTRLD_BL,
+ /* write content adaptive brightness control */
+ .wrcabc = NT35510_WRCABC_STILL_MODE,
+ /* write CABC minimum brightness */
+ .wrcabcmb = 0xff,
+};
+
+static const struct udevice_id nt35510_panel_ids[] = {
+ {
+ .compatible = "frida,frd400b25025",
+ .data = (ulong)&nt35510_frida_frd400b25025,
+ },
+ {
+ .compatible = "hydis,hva40wv1",
+ .data = (ulong)&nt35510_hydis_hva40wv1,
+ },
+ { }
+};
+
+U_BOOT_DRIVER(nt35510_panel) = {
+ .name = "nt35510_panel",
+ .id = UCLASS_PANEL,
+ .of_match = nt35510_panel_ids,
+ .ops = &nt35510_panel_ops,
+ .of_to_plat = nt35510_panel_of_to_plat,
+ .probe = nt35510_panel_probe,
+ .plat_auto = sizeof(struct mipi_dsi_panel_plat),
+ .priv_auto = sizeof(struct nt35510_panel_priv),
+};
git.openpandora.org / pandora-u-boot.git / commitdiff