sunxi: Switch to PMIC USB power supply VBUS detection

Update boards to use the USB power supply driver, as referenced in the
device tree, instead of a virtual GPIO. This removes the need for some
DM-incompatible special cases in the GPIO driver.

The following five boards used AXP0-VBUS-DETECT in their config, but are
missing the "usb0_vbus_power-supply" property in their device tree:
 - Ainol_AW1_defconfig / sun7i-a20-ainol-aw1
 - Cubieboard4_defconfig / sun9i-a80-cubieboard4
 - Merrii_A80_Optimus_defconfig / sun9i-a80-optimus
 - Yones_Toptech_BD1078_defconfig / sun7i-a20-yones-toptech-bd1078
 - Yones_Toptech_BS1078_V2_defconfig /
   sun6i-a31s-yones-toptech-bs1078-v2

None of those five boards have the MUSB controller (USB OTG) enabled in
their device trees, so this change should not break anything for them.

Additionally, the following board intentionally omits the property
because VBUS is always enabled:
 - Nintendo_NES_Classic_Edition_defconfig /
   sun8i-r16-nintendo-nes-classic

The PHY driver already assumes VBUS is enabled when no detection method
is available, so again this will not cause any problems.

Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>

diff --git a/configs/A33-OLinuXino_defconfig b/configs/A33-OLinuXino_defconfig
index fc32a86..df4acaf 100644 (file)
--- a/configs/A33-OLinuXino_defconfig
+++ b/configs/A33-OLinuXino_defconfig
@@ -7,7 +7,6 @@ CONFIG_DRAM_CLK=432
 CONFIG_DRAM_ZQ=15291
 CONFIG_DRAM_ODT_EN=y
 CONFIG_USB0_VBUS_PIN="AXP0-VBUS-ENABLE"
-CONFIG_USB0_VBUS_DET="AXP0-VBUS-DETECT"
 CONFIG_USB0_ID_DET="PB3"
 CONFIG_AXP_GPIO=y
 CONFIG_VIDEO_LCD_MODE="x:800,y:480,depth:18,pclk_khz:33000,le:16,ri:209,up:22,lo:22,hs:30,vs:1,sync:3,vmode:0"
@@ -15,5 +14,6 @@ CONFIG_VIDEO_LCD_DCLK_PHASE=0
 CONFIG_VIDEO_LCD_BL_EN="PB2"
 CONFIG_VIDEO_LCD_BL_PWM="PH0"
 # CONFIG_SYS_MALLOC_CLEAR_ON_INIT is not set
+CONFIG_REGULATOR_AXP_USB_POWER=y
 CONFIG_AXP_DCDC1_VOLT=3300
 CONFIG_USB_MUSB_HOST=y

diff --git a/configs/Ainol_AW1_defconfig b/configs/Ainol_AW1_defconfig
index 9ae3893..51f26f4 100644 (file)
--- a/configs/Ainol_AW1_defconfig
+++ b/configs/Ainol_AW1_defconfig
@@ -6,7 +6,6 @@ CONFIG_MACH_SUN7I=y
 CONFIG_DRAM_CLK=432
 CONFIG_DRAM_ZQ=123
 CONFIG_USB0_VBUS_PIN="PB9"
-CONFIG_USB0_VBUS_DET="AXP0-VBUS-DETECT"
 CONFIG_AXP_GPIO=y
 CONFIG_VIDEO_LCD_MODE="x:800,y:480,depth:18,pclk_khz:40000,le:87,ri:112,up:38,lo:141,hs:1,vs:1,sync:3,vmode:0"
 CONFIG_VIDEO_LCD_POWER="PH8"
@@ -17,4 +16,5 @@ CONFIG_SPL_I2C=y
 CONFIG_SYS_I2C_MVTWSI=y
 CONFIG_SYS_I2C_SLAVE=0x7f
 CONFIG_SYS_I2C_SPEED=400000
+CONFIG_REGULATOR_AXP_USB_POWER=y
 CONFIG_USB_MUSB_HOST=y

diff --git a/configs/Cubieboard4_defconfig b/configs/Cubieboard4_defconfig
index 5eee23f..2f93a7b 100644 (file)
--- a/configs/Cubieboard4_defconfig
+++ b/configs/Cubieboard4_defconfig
@@ -6,10 +6,11 @@ CONFIG_MACH_SUN9I=y
 CONFIG_DRAM_CLK=672
 CONFIG_MMC_SUNXI_SLOT_EXTRA=2
 CONFIG_USB0_VBUS_PIN="AXP0-VBUS-ENABLE"
-CONFIG_USB0_VBUS_DET="AXP0-VBUS-DETECT"
 CONFIG_USB0_ID_DET="PH16"
 CONFIG_USB1_VBUS_PIN="PH14"
 CONFIG_USB3_VBUS_PIN="PH15"
 CONFIG_AXP_GPIO=y
 CONFIG_SYS_I2C_SUN8I_RSB=y
+CONFIG_DM_REGULATOR=y
+CONFIG_REGULATOR_AXP_USB_POWER=y
 CONFIG_AXP809_POWER=y

diff --git a/configs/Cubietruck_plus_defconfig b/configs/Cubietruck_plus_defconfig
index 13f9589..29f4df2 100644 (file)
--- a/configs/Cubietruck_plus_defconfig
+++ b/configs/Cubietruck_plus_defconfig
@@ -8,7 +8,6 @@ CONFIG_DRAM_ZQ=15355
 CONFIG_DRAM_ODT_EN=y
 CONFIG_MMC_SUNXI_SLOT_EXTRA=2
 CONFIG_USB0_VBUS_PIN="AXP0-VBUS-ENABLE"
-CONFIG_USB0_VBUS_DET="AXP0-VBUS-DETECT"
 CONFIG_USB0_ID_DET="PH11"
 CONFIG_USB1_VBUS_PIN="PD29"
 CONFIG_USB2_VBUS_PIN="PL6"
@@ -22,6 +21,7 @@ CONFIG_SYS_I2C_SLAVE=0x7f
 CONFIG_SYS_I2C_SPEED=400000
 CONFIG_PHY_REALTEK=y
 CONFIG_SUN8I_EMAC=y
+CONFIG_REGULATOR_AXP_USB_POWER=y
 CONFIG_AXP_DLDO3_VOLT=2500
 CONFIG_AXP_DLDO4_VOLT=3300
 CONFIG_AXP_FLDO1_VOLT=1200

diff --git a/configs/MSI_Primo81_defconfig b/configs/MSI_Primo81_defconfig
index e77b007..d60eedb 100644 (file)
--- a/configs/MSI_Primo81_defconfig
+++ b/configs/MSI_Primo81_defconfig
@@ -6,13 +6,13 @@ CONFIG_MACH_SUN6I=y
 CONFIG_DRAM_CLK=360
 CONFIG_DRAM_ZQ=122
 CONFIG_USB0_VBUS_PIN="AXP0-VBUS-ENABLE"
-CONFIG_USB0_VBUS_DET="AXP0-VBUS-DETECT"
 CONFIG_AXP_GPIO=y
 CONFIG_VIDEO_LCD_MODE="x:768,y:1024,depth:18,pclk_khz:66000,le:56,ri:60,up:30,lo:36,hs:64,vs:50,sync:3,vmode:0"
 CONFIG_VIDEO_LCD_BL_EN="PA25"
 CONFIG_VIDEO_LCD_BL_PWM="PH13"
 CONFIG_VIDEO_LCD_PANEL_MIPI_4_LANE_513_MBPS_VIA_SSD2828=y
 # CONFIG_SYS_MALLOC_CLEAR_ON_INIT is not set
+CONFIG_REGULATOR_AXP_USB_POWER=y
 CONFIG_AXP_DLDO1_VOLT=3300
 # CONFIG_REQUIRE_SERIAL_CONSOLE is not set
 CONFIG_USB_MUSB_HOST=y

diff --git a/configs/Merrii_A80_Optimus_defconfig b/configs/Merrii_A80_Optimus_defconfig
index b9ccfcf..f0c54e2 100644 (file)
--- a/configs/Merrii_A80_Optimus_defconfig
+++ b/configs/Merrii_A80_Optimus_defconfig
@@ -6,10 +6,11 @@ CONFIG_MACH_SUN9I=y
 CONFIG_DRAM_CLK=672
 CONFIG_MMC_SUNXI_SLOT_EXTRA=2
 CONFIG_USB0_VBUS_PIN="AXP0-VBUS-ENABLE"
-CONFIG_USB0_VBUS_DET="AXP0-VBUS-DETECT"
 CONFIG_USB0_ID_DET="PH3"
 CONFIG_USB1_VBUS_PIN="PH4"
 CONFIG_USB3_VBUS_PIN="PH5"
 CONFIG_AXP_GPIO=y
 CONFIG_SYS_I2C_SUN8I_RSB=y
+CONFIG_DM_REGULATOR=y
+CONFIG_REGULATOR_AXP_USB_POWER=y
 CONFIG_AXP809_POWER=y

diff --git a/configs/Nintendo_NES_Classic_Edition_defconfig b/configs/Nintendo_NES_Classic_Edition_defconfig
index 18fa377..3046f45 100644 (file)
--- a/configs/Nintendo_NES_Classic_Edition_defconfig
+++ b/configs/Nintendo_NES_Classic_Edition_defconfig
@@ -6,7 +6,6 @@ CONFIG_MACH_SUN8I_A33=y
 CONFIG_DRAM_CLK=600
 CONFIG_DRAM_ZQ=15291
 CONFIG_DRAM_ODT_EN=y
-CONFIG_USB0_VBUS_DET="AXP0-VBUS-DETECT"
 CONFIG_AXP_GPIO=y
 # CONFIG_SYS_MALLOC_CLEAR_ON_INIT is not set
 # CONFIG_CMD_FLASH is not set
@@ -20,6 +19,7 @@ CONFIG_SYS_NAND_ONFI_DETECTION=y
 CONFIG_SYS_NAND_PAGE_SIZE=0x800
 CONFIG_SYS_NAND_OOBSIZE=0x40
 CONFIG_SYS_NAND_MAX_ECCPOS=1664
+CONFIG_REGULATOR_AXP_USB_POWER=y
 CONFIG_AXP_DLDO1_VOLT=3300
 CONFIG_AXP_ELDO2_VOLT=1800
 CONFIG_CONS_INDEX=5

diff --git a/configs/Sinovoip_BPI_M3_defconfig b/configs/Sinovoip_BPI_M3_defconfig
index 5116fab..5642e52 100644 (file)
--- a/configs/Sinovoip_BPI_M3_defconfig
+++ b/configs/Sinovoip_BPI_M3_defconfig
@@ -9,7 +9,6 @@ CONFIG_DRAM_ZQ=15355
 CONFIG_DRAM_ODT_EN=y
 CONFIG_MMC_SUNXI_SLOT_EXTRA=2
 CONFIG_USB0_VBUS_PIN="AXP0-VBUS-ENABLE"
-CONFIG_USB0_VBUS_DET="AXP0-VBUS-DETECT"
 CONFIG_USB0_ID_DET="PH11"
 CONFIG_USB1_VBUS_PIN="PD24"
 CONFIG_AXP_GPIO=y
@@ -19,6 +18,7 @@ CONFIG_CONSOLE_MUX=y
 CONFIG_PHY_REALTEK=y
 CONFIG_SUN8I_EMAC=y
 CONFIG_INITIAL_USB_SCAN_DELAY=500
+CONFIG_REGULATOR_AXP_USB_POWER=y
 CONFIG_AXP_DCDC5_VOLT=1200
 CONFIG_AXP_DLDO3_VOLT=3300
 CONFIG_AXP_SW_ON=y

diff --git a/configs/Wexler_TAB7200_defconfig b/configs/Wexler_TAB7200_defconfig
index 101ce57..40aeb66 100644 (file)
--- a/configs/Wexler_TAB7200_defconfig
+++ b/configs/Wexler_TAB7200_defconfig
@@ -5,7 +5,6 @@ CONFIG_SPL=y
 CONFIG_MACH_SUN7I=y
 CONFIG_DRAM_CLK=384
 CONFIG_USB0_VBUS_PIN="PB9"
-CONFIG_USB0_VBUS_DET="AXP0-VBUS-DETECT"
 CONFIG_USB0_ID_DET="PH4"
 CONFIG_AXP_GPIO=y
 CONFIG_VIDEO_LCD_MODE="x:800,y:480,depth:24,pclk_khz:33000,le:45,ri:210,up:22,lo:22,hs:1,vs:1,sync:3,vmode:0"
@@ -17,6 +16,7 @@ CONFIG_SPL_I2C=y
 CONFIG_SYS_I2C_MVTWSI=y
 CONFIG_SYS_I2C_SLAVE=0x7f
 CONFIG_SYS_I2C_SPEED=400000
+CONFIG_REGULATOR_AXP_USB_POWER=y
 CONFIG_USB_EHCI_HCD=y
 CONFIG_USB_OHCI_HCD=y
 CONFIG_USB_MUSB_HOST=y

diff --git a/configs/Yones_Toptech_BD1078_defconfig b/configs/Yones_Toptech_BD1078_defconfig
index 4f2290c..9b13659 100644 (file)
--- a/configs/Yones_Toptech_BD1078_defconfig
+++ b/configs/Yones_Toptech_BD1078_defconfig
@@ -7,7 +7,6 @@ CONFIG_DRAM_CLK=408
 CONFIG_MMC1_PINS_PH=y
 CONFIG_MMC_SUNXI_SLOT_EXTRA=1
 CONFIG_USB0_VBUS_PIN="PB9"
-CONFIG_USB0_VBUS_DET="AXP0-VBUS-DETECT"
 CONFIG_AXP_GPIO=y
 CONFIG_VIDEO_LCD_MODE="x:1024,y:600,depth:24,pclk_khz:63000,le:32,ri:287,up:22,lo:12,hs:1,vs:1,sync:3,vmode:0"
 CONFIG_VIDEO_LCD_DCLK_PHASE=0
@@ -21,4 +20,5 @@ CONFIG_SPL_I2C=y
 CONFIG_SYS_I2C_MVTWSI=y
 CONFIG_SYS_I2C_SLAVE=0x7f
 CONFIG_SYS_I2C_SPEED=400000
+CONFIG_REGULATOR_AXP_USB_POWER=y
 CONFIG_USB_MUSB_HOST=y

diff --git a/configs/Yones_Toptech_BS1078_V2_defconfig b/configs/Yones_Toptech_BS1078_V2_defconfig
index b33c825..de69ebe 100644 (file)
--- a/configs/Yones_Toptech_BS1078_V2_defconfig
+++ b/configs/Yones_Toptech_BS1078_V2_defconfig
@@ -6,7 +6,6 @@ CONFIG_MACH_SUN6I=y
 CONFIG_DRAM_CLK=420
 CONFIG_DRAM_ZQ=251
 CONFIG_USB0_VBUS_PIN="AXP0-VBUS-ENABLE"
-CONFIG_USB0_VBUS_DET="AXP0-VBUS-DETECT"
 CONFIG_USB0_ID_DET="PA15"
 CONFIG_AXP_GPIO=y
 CONFIG_VIDEO_LCD_MODE="x:1024,y:600,depth:24,pclk_khz:70000,le:120,ri:180,up:17,lo:15,hs:20,vs:3,sync:3,vmode:0"
@@ -15,5 +14,6 @@ CONFIG_VIDEO_LCD_BL_EN="PA25"
 CONFIG_VIDEO_LCD_BL_PWM="PH13"
 CONFIG_VIDEO_LCD_PANEL_LVDS=y
 # CONFIG_SYS_MALLOC_CLEAR_ON_INIT is not set
+CONFIG_REGULATOR_AXP_USB_POWER=y
 CONFIG_AXP_DLDO1_VOLT=3300
 CONFIG_USB_MUSB_HOST=y

diff --git a/configs/colorfly_e708_q1_defconfig b/configs/colorfly_e708_q1_defconfig
index 89f063b..07bda04 100644 (file)
--- a/configs/colorfly_e708_q1_defconfig
+++ b/configs/colorfly_e708_q1_defconfig
@@ -6,7 +6,6 @@ CONFIG_MACH_SUN6I=y
 CONFIG_DRAM_CLK=432
 CONFIG_DRAM_ZQ=251
 CONFIG_USB0_VBUS_PIN="AXP0-VBUS-ENABLE"
-CONFIG_USB0_VBUS_DET="AXP0-VBUS-DETECT"
 CONFIG_USB0_ID_DET="PA15"
 CONFIG_AXP_GPIO=y
 CONFIG_VIDEO_LCD_MODE="x:800,y:1280,depth:24,pclk_khz:64000,le:20,ri:34,up:1,lo:16,hs:10,vs:1,sync:3,vmode:0"
@@ -15,6 +14,7 @@ CONFIG_VIDEO_LCD_BL_EN="PA25"
 CONFIG_VIDEO_LCD_BL_PWM="PH13"
 CONFIG_VIDEO_LCD_PANEL_LVDS=y
 # CONFIG_SYS_MALLOC_CLEAR_ON_INIT is not set
+CONFIG_REGULATOR_AXP_USB_POWER=y
 CONFIG_AXP_DLDO1_VOLT=3300
 CONFIG_AXP_DLDO2_VOLT=1800
 CONFIG_USB_MUSB_HOST=y

diff --git a/configs/ga10h_v1_1_defconfig b/configs/ga10h_v1_1_defconfig
index 599eeb9..935071d 100644 (file)
--- a/configs/ga10h_v1_1_defconfig
+++ b/configs/ga10h_v1_1_defconfig
@@ -7,7 +7,6 @@ CONFIG_DRAM_CLK=432
 CONFIG_DRAM_ZQ=15291
 CONFIG_DRAM_ODT_EN=y
 CONFIG_USB0_VBUS_PIN="AXP0-VBUS-ENABLE"
-CONFIG_USB0_VBUS_DET="AXP0-VBUS-DETECT"
 CONFIG_USB0_ID_DET="PH8"
 CONFIG_AXP_GPIO=y
 CONFIG_VIDEO_LCD_MODE="x:1024,y:600,depth:18,pclk_khz:52000,le:138,ri:162,up:22,lo:10,hs:20,vs:3,sync:3,vmode:0"
@@ -17,6 +16,7 @@ CONFIG_VIDEO_LCD_BL_EN="PH6"
 CONFIG_VIDEO_LCD_BL_PWM="PH0"
 CONFIG_VIDEO_LCD_PANEL_LVDS=y
 # CONFIG_SYS_MALLOC_CLEAR_ON_INIT is not set
+CONFIG_REGULATOR_AXP_USB_POWER=y
 CONFIG_AXP_DLDO1_VOLT=3300
 CONFIG_CONS_INDEX=5
 CONFIG_USB_EHCI_HCD=y

diff --git a/configs/gt90h_v4_defconfig b/configs/gt90h_v4_defconfig
index f5e3a72..205eab2 100644 (file)
--- a/configs/gt90h_v4_defconfig
+++ b/configs/gt90h_v4_defconfig
@@ -6,7 +6,6 @@ CONFIG_MACH_SUN8I_A23=y
 CONFIG_DRAM_CLK=480
 CONFIG_DRAM_ZQ=32767
 CONFIG_USB0_VBUS_PIN="AXP0-VBUS-ENABLE"
-CONFIG_USB0_VBUS_DET="AXP0-VBUS-DETECT"
 CONFIG_USB0_ID_DET="PH8"
 CONFIG_AXP_GPIO=y
 CONFIG_VIDEO_LCD_MODE="x:1024,y:600,depth:18,pclk_khz:55000,le:159,ri:160,up:22,lo:12,hs:1,vs:1,sync:3,vmode:0"
@@ -15,6 +14,7 @@ CONFIG_VIDEO_LCD_POWER="PH7"
 CONFIG_VIDEO_LCD_BL_EN="PH6"
 CONFIG_VIDEO_LCD_BL_PWM="PH0"
 # CONFIG_SYS_MALLOC_CLEAR_ON_INIT is not set
+CONFIG_REGULATOR_AXP_USB_POWER=y
 CONFIG_AXP_DLDO1_VOLT=3300
 CONFIG_CONS_INDEX=5
 CONFIG_USB_MUSB_HOST=y

diff --git a/configs/iNet_D978_rev2_defconfig b/configs/iNet_D978_rev2_defconfig
index e01e184..ed6a603 100644 (file)
--- a/configs/iNet_D978_rev2_defconfig
+++ b/configs/iNet_D978_rev2_defconfig
@@ -6,7 +6,6 @@ CONFIG_MACH_SUN8I_A33=y
 CONFIG_DRAM_CLK=456
 CONFIG_DRAM_ZQ=15291
 CONFIG_USB0_VBUS_PIN="AXP0-VBUS-ENABLE"
-CONFIG_USB0_VBUS_DET="AXP0-VBUS-DETECT"
 CONFIG_USB0_ID_DET="PH8"
 CONFIG_AXP_GPIO=y
 CONFIG_VIDEO_LCD_MODE="x:1024,y:768,depth:18,pclk_khz:65000,le:120,ri:180,up:22,lo:13,hs:20,vs:3,sync:3,vmode:0"
@@ -16,6 +15,7 @@ CONFIG_VIDEO_LCD_BL_EN="PH6"
 CONFIG_VIDEO_LCD_BL_PWM="PH0"
 CONFIG_VIDEO_LCD_PANEL_LVDS=y
 # CONFIG_SYS_MALLOC_CLEAR_ON_INIT is not set
+CONFIG_REGULATOR_AXP_USB_POWER=y
 CONFIG_AXP_DLDO1_VOLT=3300
 # CONFIG_REQUIRE_SERIAL_CONSOLE is not set
 CONFIG_CONS_INDEX=5

diff --git a/configs/inet86dz_defconfig b/configs/inet86dz_defconfig
index 2035a34..d215a83 100644 (file)
--- a/configs/inet86dz_defconfig
+++ b/configs/inet86dz_defconfig
@@ -6,7 +6,6 @@ CONFIG_MACH_SUN8I_A23=y
 CONFIG_DRAM_CLK=552
 CONFIG_DRAM_ZQ=63351
 CONFIG_USB0_VBUS_PIN="AXP0-VBUS-ENABLE"
-CONFIG_USB0_VBUS_DET="AXP0-VBUS-DETECT"
 CONFIG_USB0_ID_DET="PH8"
 CONFIG_AXP_GPIO=y
 CONFIG_VIDEO_LCD_MODE="x:1024,y:600,depth:18,pclk_khz:51000,le:138,ri:162,up:22,lo:10,hs:20,vs:3,sync:3,vmode:0"
@@ -15,6 +14,7 @@ CONFIG_VIDEO_LCD_POWER="PH7"
 CONFIG_VIDEO_LCD_BL_EN="PH6"
 CONFIG_VIDEO_LCD_BL_PWM="PH0"
 # CONFIG_SYS_MALLOC_CLEAR_ON_INIT is not set
+CONFIG_REGULATOR_AXP_USB_POWER=y
 CONFIG_AXP_DLDO1_VOLT=3300
 CONFIG_CONS_INDEX=5
 CONFIG_USB_MUSB_HOST=y

diff --git a/configs/inet_q972_defconfig b/configs/inet_q972_defconfig
index 85a3b4e..24ff6c0 100644 (file)
--- a/configs/inet_q972_defconfig
+++ b/configs/inet_q972_defconfig
@@ -6,7 +6,6 @@ CONFIG_MACH_SUN6I=y
 CONFIG_DRAM_CLK=384
 CONFIG_DRAM_ZQ=251
 CONFIG_USB0_VBUS_PIN="AXP0-VBUS-ENABLE"
-CONFIG_USB0_VBUS_DET="AXP0-VBUS-DETECT"
 CONFIG_USB0_ID_DET="PA15"
 CONFIG_AXP_GPIO=y
 CONFIG_VIDEO_LCD_MODE="x:1024,y:768,depth:18,pclk_khz:65000,le:280,ri:20,up:22,lo:8,hs:20,vs:8,sync:3,vmode:0"
@@ -14,6 +13,7 @@ CONFIG_VIDEO_LCD_DCLK_PHASE=0
 CONFIG_VIDEO_LCD_BL_EN="PA25"
 CONFIG_VIDEO_LCD_BL_PWM="PH13"
 # CONFIG_SYS_MALLOC_CLEAR_ON_INIT is not set
+CONFIG_REGULATOR_AXP_USB_POWER=y
 CONFIG_AXP_DLDO1_VOLT=3300
 CONFIG_USB_EHCI_HCD=y
 CONFIG_USB_OHCI_HCD=y

diff --git a/configs/polaroid_mid2407pxe03_defconfig b/configs/polaroid_mid2407pxe03_defconfig
index 023f880..6ec7c83 100644 (file)
--- a/configs/polaroid_mid2407pxe03_defconfig
+++ b/configs/polaroid_mid2407pxe03_defconfig
@@ -6,7 +6,6 @@ CONFIG_MACH_SUN8I_A23=y
 CONFIG_DRAM_CLK=432
 CONFIG_DRAM_ZQ=63351
 CONFIG_USB0_VBUS_PIN="AXP0-VBUS-ENABLE"
-CONFIG_USB0_VBUS_DET="AXP0-VBUS-DETECT"
 CONFIG_USB0_ID_DET="PH8"
 CONFIG_AXP_GPIO=y
 CONFIG_VIDEO_LCD_MODE="x:800,y:480,depth:18,pclk_khz:33000,le:87,ri:40,up:31,lo:13,hs:1,vs:1,sync:3,vmode:0"
@@ -15,6 +14,7 @@ CONFIG_VIDEO_LCD_POWER="PH7"
 CONFIG_VIDEO_LCD_BL_EN="PH6"
 CONFIG_VIDEO_LCD_BL_PWM="PH0"
 # CONFIG_SYS_MALLOC_CLEAR_ON_INIT is not set
+CONFIG_REGULATOR_AXP_USB_POWER=y
 CONFIG_AXP_DLDO1_VOLT=3300
 CONFIG_CONS_INDEX=5
 CONFIG_USB_MUSB_HOST=y

diff --git a/configs/polaroid_mid2809pxe04_defconfig b/configs/polaroid_mid2809pxe04_defconfig
index 2e9efd0..1aefc50 100644 (file)
--- a/configs/polaroid_mid2809pxe04_defconfig
+++ b/configs/polaroid_mid2809pxe04_defconfig
@@ -6,7 +6,6 @@ CONFIG_MACH_SUN8I_A23=y
 CONFIG_DRAM_CLK=432
 CONFIG_DRAM_ZQ=63351
 CONFIG_USB0_VBUS_PIN="AXP0-VBUS-ENABLE"
-CONFIG_USB0_VBUS_DET="AXP0-VBUS-DETECT"
 CONFIG_USB0_ID_DET="PH8"
 CONFIG_AXP_GPIO=y
 CONFIG_VIDEO_LCD_MODE="x:800,y:480,depth:18,pclk_khz:33000,le:36,ri:210,up:18,lo:22,hs:10,vs:5,sync:3,vmode:0"
@@ -15,6 +14,7 @@ CONFIG_VIDEO_LCD_POWER="PH7"
 CONFIG_VIDEO_LCD_BL_EN="PH6"
 CONFIG_VIDEO_LCD_BL_PWM="PH0"
 # CONFIG_SYS_MALLOC_CLEAR_ON_INIT is not set
+CONFIG_REGULATOR_AXP_USB_POWER=y
 CONFIG_AXP_DLDO1_VOLT=3300
 CONFIG_CONS_INDEX=5
 CONFIG_USB_MUSB_HOST=y

diff --git a/configs/q8_a23_tablet_800x480_defconfig b/configs/q8_a23_tablet_800x480_defconfig
index 3bfc5c5..0f8c30e 100644 (file)
--- a/configs/q8_a23_tablet_800x480_defconfig
+++ b/configs/q8_a23_tablet_800x480_defconfig
@@ -6,7 +6,6 @@ CONFIG_MACH_SUN8I_A23=y
 CONFIG_DRAM_CLK=432
 CONFIG_DRAM_ZQ=63306
 CONFIG_USB0_VBUS_PIN="AXP0-VBUS-ENABLE"
-CONFIG_USB0_VBUS_DET="AXP0-VBUS-DETECT"
 CONFIG_USB0_ID_DET="PH8"
 CONFIG_AXP_GPIO=y
 CONFIG_VIDEO_LCD_MODE="x:800,y:480,depth:18,pclk_khz:33000,le:36,ri:210,up:18,lo:22,hs:10,vs:5,sync:3,vmode:0"
@@ -15,6 +14,7 @@ CONFIG_VIDEO_LCD_POWER="PH7"
 CONFIG_VIDEO_LCD_BL_EN="PH6"
 CONFIG_VIDEO_LCD_BL_PWM="PH0"
 # CONFIG_SYS_MALLOC_CLEAR_ON_INIT is not set
+CONFIG_REGULATOR_AXP_USB_POWER=y
 CONFIG_AXP_DLDO1_VOLT=3300
 CONFIG_CONS_INDEX=5
 CONFIG_USB_MUSB_HOST=y

diff --git a/configs/q8_a33_tablet_1024x600_defconfig b/configs/q8_a33_tablet_1024x600_defconfig
index 9166ec0..b3b5cc7 100644 (file)
--- a/configs/q8_a33_tablet_1024x600_defconfig
+++ b/configs/q8_a33_tablet_1024x600_defconfig
@@ -6,7 +6,6 @@ CONFIG_MACH_SUN8I_A33=y
 CONFIG_DRAM_CLK=456
 CONFIG_DRAM_ZQ=15291
 CONFIG_USB0_VBUS_PIN="AXP0-VBUS-ENABLE"
-CONFIG_USB0_VBUS_DET="AXP0-VBUS-DETECT"
 CONFIG_USB0_ID_DET="PH8"
 CONFIG_AXP_GPIO=y
 CONFIG_VIDEO_LCD_MODE="x:1024,y:600,depth:18,pclk_khz:51000,le:159,ri:160,up:22,lo:12,hs:1,vs:1,sync:3,vmode:0"
@@ -15,6 +14,7 @@ CONFIG_VIDEO_LCD_POWER="PH7"
 CONFIG_VIDEO_LCD_BL_EN="PH6"
 CONFIG_VIDEO_LCD_BL_PWM="PH0"
 # CONFIG_SYS_MALLOC_CLEAR_ON_INIT is not set
+CONFIG_REGULATOR_AXP_USB_POWER=y
 CONFIG_AXP_DLDO1_VOLT=3300
 CONFIG_CONS_INDEX=5
 CONFIG_USB_MUSB_HOST=y

diff --git a/configs/q8_a33_tablet_800x480_defconfig b/configs/q8_a33_tablet_800x480_defconfig
index 6114fcb..37ee08f 100644 (file)
--- a/configs/q8_a33_tablet_800x480_defconfig
+++ b/configs/q8_a33_tablet_800x480_defconfig
@@ -6,7 +6,6 @@ CONFIG_MACH_SUN8I_A33=y
 CONFIG_DRAM_CLK=456
 CONFIG_DRAM_ZQ=15291
 CONFIG_USB0_VBUS_PIN="AXP0-VBUS-ENABLE"
-CONFIG_USB0_VBUS_DET="AXP0-VBUS-DETECT"
 CONFIG_USB0_ID_DET="PH8"
 CONFIG_AXP_GPIO=y
 CONFIG_VIDEO_LCD_MODE="x:800,y:480,depth:18,pclk_khz:33000,le:87,ri:167,up:31,lo:13,hs:1,vs:1,sync:3,vmode:0"
@@ -15,6 +14,7 @@ CONFIG_VIDEO_LCD_POWER="PH7"
 CONFIG_VIDEO_LCD_BL_EN="PH6"
 CONFIG_VIDEO_LCD_BL_PWM="PH0"
 # CONFIG_SYS_MALLOC_CLEAR_ON_INIT is not set
+CONFIG_REGULATOR_AXP_USB_POWER=y
 CONFIG_AXP_DLDO1_VOLT=3300
 CONFIG_CONS_INDEX=5
 CONFIG_USB_MUSB_HOST=y

diff --git a/configs/tbs_a711_defconfig b/configs/tbs_a711_defconfig
index b3c2e69..9a70b6b 100644 (file)
--- a/configs/tbs_a711_defconfig
+++ b/configs/tbs_a711_defconfig
@@ -9,11 +9,11 @@ CONFIG_DRAM_ZQ=15355
 CONFIG_DRAM_ODT_EN=y
 CONFIG_MMC_SUNXI_SLOT_EXTRA=2
 CONFIG_USB0_VBUS_PIN="AXP0-VBUS-ENABLE"
-CONFIG_USB0_VBUS_DET="AXP0-VBUS-DETECT"
 CONFIG_USB0_ID_DET="PH11"
 CONFIG_AXP_GPIO=y
 # CONFIG_SYS_MALLOC_CLEAR_ON_INIT is not set
 CONFIG_FASTBOOT_CMD_OEM_FORMAT=y
+CONFIG_REGULATOR_AXP_USB_POWER=y
 CONFIG_AXP_DCDC5_VOLT=1200
 CONFIG_USB_EHCI_HCD=y
 CONFIG_USB_OHCI_HCD=y