i2c: omap24xx_i2c: support CONFIG for repeated start in DM_I2C xfer

Repeated Start Condition (Sr) can be used to transfer multiple i2c msgs
without sending a Stop condition (P). So far, the driver default was to
always send a Stop condition after every i2c msg.

Add support for a config option (CONFIG_SYS_I2C_OMAP24XX_REPEATED_START)
to disable sending the Stop condition by default. If this config is
enabled, Stop condition will be sent only if explicitly requested in the
msg flags OR if it is the last msg in the transfer.

Consequently, handle the Repeated Start condition (Sr) in the next msg
by not calling the wait_for_bb() check since it will simply timeout in
the absence of a stop condition (BB will be 1 until Stop is programmed)

Signed-off-by: Aniket Limaye <a-limaye@ti.com>
Reviewed-by: Heiko Schocher <hs@denx.de>

diff --git a/drivers/i2c/omap24xx_i2c.c b/drivers/i2c/omap24xx_i2c.c
index 4afdba0..a6361d3 100644 (file)
--- a/drivers/i2c/omap24xx_i2c.c
+++ b/drivers/i2c/omap24xx_i2c.c
@@ -1066,18 +1066,28 @@ static int omap_i2c_xfer(struct udevice *bus, struct i2c_msg *msg, int nmsgs)
        u16 i2c_con_reg = 0;
 
        debug("%s: %d messages\n", __func__, nmsgs);
-       for (; nmsgs > 0; nmsgs--, msg++) {
-               /* Wait until bus not busy */
-               if (wait_for_bb(priv->regs, priv->ip_rev, priv->waitdelay))
-                       return -EREMOTEIO;
+       for (int i = 0; i < nmsgs; i++, msg++) {
+               /*
+                * If previous msg sent a Stop or if this is the first msg
+                * Wait until bus not busy
+                */
+               if ((i2c_con_reg & I2C_CON_STP) || (i == 0))
+                       if (wait_for_bb(priv->regs, priv->ip_rev, priv->waitdelay))
+                               return -EREMOTEIO;
 
-               /* Set Controller mode with Start and Stop bit */
-               i2c_con_reg = I2C_CON_EN | I2C_CON_MST | I2C_CON_STT | I2C_CON_STP;
+               /* Set Controller mode with Start bit */
+               i2c_con_reg = I2C_CON_EN | I2C_CON_MST | I2C_CON_STT;
                /* Set Transmitter/Receiver mode if it is a write/read msg */
                if (msg->flags & I2C_M_RD)
                        i2c_con_reg &= ~I2C_CON_TRX;
                else
                        i2c_con_reg |= I2C_CON_TRX;
+               /* Send Stop condition (P) by default */
+               if (!IS_ENABLED(CONFIG_SYS_I2C_OMAP24XX_REPEATED_START))
+                       i2c_con_reg |= I2C_CON_STP;
+               /* Send Stop if explicitly requested or if this is the last msg */
+               if ((msg->flags & I2C_M_STOP) || (i == nmsgs - 1))
+                       i2c_con_reg |= I2C_CON_STP;
 
                debug("%s: chip=0x%x, len=0x%x, i2c_con_reg=0x%x\n",
                      __func__, msg->addr, msg->len, i2c_con_reg);